Software core centre problem

i have purchased a kt6 delta lsr , my problem is i cant use the software core centre dont ejecute ,not appear in nobody place

Try downloading the latest version from this website AFTER you uninstall the one you have on there now. BD51 !.5.8 I believe is the version you need.

Similar Messages

Bios 1.6 and Core Centre Problems!

Hi MSI Buddies!
I have an 875p Neo mobo,
I had problems before where my mobo wouldn't cold boot. I got a replacement board (with bios 1.20) which works perfectly.
I sucessfully upgraded to bios 1.60 last night and the version of corecentre kept stopping my CPU fan !!!! Arrrrggggghhhhh! Can't MSI get anything right (even 6th time round !!!)
I upgraded to 1.0.5.3 version of CoreCentre which fixed the CPU Fan stopping but, the FSB defaults to 203 instead of 200. Everytime i tried to put it back to 200 the PC completely froze !!!! I then ran live update and got the very latest Core Centre which still sets FSB to 203 but i can adjust it without it freezing. But it resets to 203 after a reboot! ANY IDEAS????
The CPU temp stays between 41c and 59c. Is this going to affect my CPU or cause any problems????
Also in the bios, Performance is set to FAST (this was by default).
Is there anyway i can re-flash back to 1.20 bios????
PLEASE PLEASE HELP
T Hatley.

Quote
Originally posted by thatley
Hi MSI Buddies!
I have an 875p Neo mobo,
I had problems before where my mobo wouldn\'t cold boot. I got a replacement board (with bios 1.20) which works perfectly.
I sucessfully upgraded to bios 1.60 last night and the version of corecentre kept stopping my CPU fan !!!! Arrrrggggghhhhh! Can\'t MSI get anything right (even 6th time round !!!)
I upgraded to 1.0.5.3 version of CoreCentre which fixed the CPU Fan stopping but, the FSB defaults to 203 instead of 200. Everytime i tried to put it back to 200 the PC completely froze !!!! I then ran live update and got the very latest Core Centre which still sets FSB to 203 but i can adjust it without it freezing. But it resets to 203 after a reboot! ANY IDEAS????
The CPU temp stays between 41c and 59c. Is this going to affect my CPU or cause any problems????
Also in the bios, Performance is set to FAST (this was by default).
Is there anyway i can re-flash back to 1.20 bios????
PLEASE PLEASE HELP
T Hatley.
Use Corecenter solely for checking speeds/temps.
There were lots of problems with this program so it might still behave weird sometimes. Also take into account you're directly over/under/clocking the system while it's running, you can never predict it's stability.
The 203 FSB is directly caused by the setting FAST in the bios. Those settings regulate different levels of overclocking. Try setting it to slow and tell me what corecenter says the FSB is then?
Regards

K8N Neo4 BIOS Flash Core centre problem

Hi All,
New here and with a question so here we go,
recently updated my bios with MSI live monitor and it updated the bios and everything is fine and works well except for core centre, evertime the computer starts it says core centre isn't compatible with your motherboard, have i done something wron and go back to previous bios version or is there a fix?? any help would be good.
thanks

Quote from: sixth on 03-September-05, 08:26:28
I just flashed my bios to version 1.8....i cant it to post past the windows xp boot screen.....anyone know why and what i can do??!!?!
Everything was fine before running 1.5....
I read a thread somewhere in this forum saying 1.8 is good if you have Sempron (E6?). If by some reason you have to flash 1.8, search for User syar2003's post. I followed his procedures and I flashed 1.6 successfully. Bios 1.5 gave me a lot of troubles.

KT6 Delta - Core Centre seems to have broken it!

My spec is as follows
KT6 Delta motherboard
AMD Athlon XP2600+
Crucial DDR400 3200 512MB Ram
160GB SATA hard drive
Radeon 9700PRO
Windows XP Home
The machine has been running absolutely fine for months until I foolishly decided to press the auto button in core centre for optimising clocks etc.
This resulted in the machine crashing followed by booting failure just after the Windows splash screen comes up.
The machine will boot with another IDE disk - but after installation of XP the mouse fails to operate???
As soon as the SATA disk is reconnected and configured as a non boot device, the same boot failure happens again.
I have also tried resetting the CMOS to no effect.
Any suggestions would be gratefully received.

I had that problem due to my 9800PRO.Dont know why,but a fresh format needs to be done all underclocked and with a old cheap video card installed.After you load winxp and get everything working,load VIA drivers then put the ATI card in,load its drivers and you should be good to go.I did this on 2 machines so far with no problems.Don't know what it is about ATI and a fresh install,but it makes windows xp do weird stuff.I also found that setting the FSB and uping the ram to the correct MHZ also causes winxp problems when doing the install.That is why I leave it "ALL" underclocked until I get it loaded(win xp)then the VIA drivers next before installing the ATI card and it's drivers.
You also said the mouse fails to operate.When I do a fresh install,I have to use the ps2 mouse adapter instead of the USB or the mouse will fail.
I dont know if anything I said will help you or not,but I had spent hours and hours trying to figure out how to load up everything with my combo the correct way.FWIW,I had always had a problem with getting my ram to 400mhz setting with my combo.Tried BIOS flash,reformat,fresh install's of all drivers ect......After using the following procedure above,I could change the ram to the 400mhz where it needed to be and it was all because of an improper loading procedure that I could not find posted anywheres.
Good Luck

MSI 975x Power Up Edition, W-64bit, Dual Core Centre won't install

I have the following setup
Motherboard   MSI S775 Intel 975X ATx Audio Lan power Up Edition
Chip      Intel Core 2 Duo E6400 Socket 775 2.13GHz
Chip Fan     QuietPC SCYTHE Ninja-Plus Heatpipe
Grapics Card   XFX GeForce 8800GTX 768MB DDR3 PCIE Dual DVI TVo
Case      Thermaltake VA7000SWA Shark Aluminium Full Tower - Silver
Power Supply   Tagan 800W PSU - Dual Engine
Ram      Corsair Memory 2X1GB XMS2-6400 240 DIMM UNBUFFERED PRO DDR2 LED
Network Card   Buffalo Airstation 125* High-Speed Wireless Desktop PCI Adapter + AOSS
Hard Drive   2x Western Digital Caviar 250GB S300 16mb 7200rpm
DVD Writer   NEC 18X DVD+/+RW/12X RAM IDE LabelFlash Silver OEM
Windows      Microsoft Win XP Pro 64B OEM & Vista Upgrade Coupon
The problem I have is that when I try and install the Duo Core centre I get the following VBIOS error
Flash_MMIO_MAP DeviceIoControl error
twice before starting the Install wizard. The wizard works and asks me to reboot. After reboot the App won't work at all. I have uninstalled and installed a few times but to no avail. Is there anything else I can do.
Many Thanks

Quote from: DryHeat on 08-February-07, 04:45:21
Support OS: Windows XP/2000/Vista
Does not support x64 and you are better off without it.
Quote from: manitou153 on 02-June-07, 22:40:10
I have the same problem with this following error trying to install the Dual Core Center 2.0.0.6 : "runtime error. Could not call proc".
How can I fix the problem ? I use Windows Vista Ultimate Edition 64.
In other words, MSI Dual Core Center does not support Windows Vista 64. You can try CoreTemp, but again since you have x64 you need to read this: http://www.alcpu.com/forums/viewtopic.php?t=211

MSI Core Centre ANNOYING!!!!!

Ok i recently upgraded the cooling on my amd 64 3700 sandiego be cause i found that the stock heatsink and fan sucked. so i purchased a Gigabyte G-Power pro. This is a great cooler and cools the cpu much better however i have found that since i have imstalled it MSI Core Centre keeps popping up from the system tray and making teh alarm noise, now i don't know why it does this because all the temps voltages and speeds are fine, and no overclocking has been done, it isn't even highlighting the bit thats supposed to be causing the problem, and the alarm will stop after a few seconds. but it's really annoying when playing a game and your whole game mnimizes and core centre pops up i have installed the latest version too. pls help

I don't use corecenter while gaming,but maybe you can edit the HW.ini file in "C:\Program Files\MSI\Core Center"
It lists all the settings for fan speed limits etc. , maybe your new fan drops below the minimum setting which is at 1000 by default.
Or some other setting that influences this.
Have you btw speedfan running at the same time?Because when in that program the wrong fan divider is set corecenter also sounds alarm.
I found this when setting a different value for my northbridge fan,my cpu fan dropped to 150 rpm in corecenter,still it maintained the same temperature and ofcourse the fan ran at full speed (3300rpm).

Core Centre 1.5.80

Installed the latest version of MSI's Core Centre, v1.5.80, think it's only been out a few days, but already I'm having the same error message over & over again about a "Hardware Monitor" failing to load or something. It pops up twice and then reboots itself whenever I turn on my PC. Once it's rebooted it work's fine but it clearly isn't working properly. I've e-mailed MSI UK & MSI.com but so far the only response I got back was from the UK and all they said was to download the latest version, the very version I was e-mailing them about. Used MSCONFIG to disable at startup but it's a pain in the butt starting it manually everytime I use my PC. Any help/constructive suggestions would really be appreciated.

I got the same problem after defragmenting my harddrive. The defragmenter optimize winxp startup/boot which causes I think core center to load before the hardware monitor driver.
The only solution at the moment is to remove core center from the startup folder and start it manually.
OR you could try to add the following line 'start /belownormal \corecenter.exe' in the shortcut for core center which is in the startup folder.
This will force core center to start after all normal prio apps have started and by that time the hardware monitor driver should have been loaded.

Core Centre Question

I have just updated both of my PC's to the latest 3.9 BIOS and also the latest edition of core centre (2.0.1.2), now in the PC that my other half uses, which is the same spec as mine (only way to build mine without getting major grief ) except that she has Crucial XMS PC3200 memory, 2GB 4x512MB in matched pairs, I've now noticed that it runs at DDR400, as before I could only get it to run at DDR333. Thats running at stock settings in the BIOS, so a nice Improvment there.
On my own PC, I've noticed that I'm able to get my own memory to run higher than before, and also the CPU runs a lot higher, (changing FSB only) another nice improvment!
At the moment, mine is running at 2,53 GHz rock stable for the last few days 24/7 with the temp never exceeding 36c. The only thing that I've noticed is with core centre, which now says that it does not support my M/Board! (wind the CPU back down to say 222 Bus speed then it works fine, which is the 11% overclock in core centre - and no before you ask, my settings were done in BIOS, not via core centre utility)
I'm not really complaining, dont get me wrong I think the improvment to the BIOS is a positive move. I just wonder if anyone else has noticed the problem with Core Centre and CPU overclock speeds.

I agree, i've done mine the manual way also, I just used Core Centre as an easy way to monitor my temps and to adjust my cpu fan speed. my question was why overclocking the CPU caused Core Centre to report that it did not support my motherboard, and fail to load, but would load at moderate overclocks supported by Core Centre itself. Its not the end of the world type of thing, just me being curious thats all

Core Centre... Is it safe?

Hello,
As the title is core centre safe?
Had a go at auto settings and got a windows stability problem and had to reboot.
(at around 220 mhz).
Rebooted and it levelled at 218 mhz.
I then put it back to defaults as I did'nt want to cause any damage.
If you use cc in auto mode will it make sure that your settings are safe all the time?
How does this effect your warranty with msi/ amd?
Thanks.

Core center does not keep adjusting it self. It will keep pushing your system to the limit untill you take over and do something. As for burning and neglecting hardware I found that companies generally don't even ask what happened they just send out a replacement. I've fried a harddrive and even snapped a transistor off my video card and had no problem getting them replaced. The parts cost next to nothing to produce, it's what goes into their development that pushes up prices. The companies tend to be more concerned with your return business rather than crying over why you cranked on your processor.

MSI DUO CORE CENTRE APPLICATION

Hi all, i would like to try out OC and would like to test with the software first.
However, I cannot click on the D.O.T (Dynamic OC) button in the DUO CORE CENTRE program. Nor was there any UP and DOWN buttons beside the DOT that I can adjust the settings.
I am using AMD 5200, wif latest BIOS installed. VGA is XpertVision 8800GT. My MOBO is MSI K9NGM3.
Explored the application but only settings for the VGA can be tweaked. Understand that Multiplier cannot be OC but FSB should be able to. Nothing can be adjusted under the Mainboard settings.
Could anyone provide some guidelines?
[P.S. Would also like to know how much to OC with my 5200]
Thanks!

Quote from: AaronYuri on 29-January-08, 12:32:40
125w CPUs are NOT supported by your board. Understand the risk you are taking overclocking such a budget board... You could end up melting the MOSFETs.
5000+/5200+ get to around 3GHz on a guess of 1.375v-1.425v. Beyond usually takes some voltage. You can clear CMOS via CMOS jumper: Clear CMOS Guide
*** But I highly recommend you do not overclock with this board. ***
Thanks for the advice. As i only recently began building my own PC, I didnt chose high end stuff yet.
But a bit of OC also not adviseable? Maybe on stock fan.
I am interested in the X47 board but all things must start from basics first :D

Core centre correct temp

after having problems with core centre reading various temps from 38c to 66c on start up !
think ive found a way to get it stable and sorted
just remove from windows start up ( using tweak-xp) and it has now booted at least ten times with a regular temp reading mid 40`s rising to 49 c
if it stays like that ill be happy !
just need to click on desktop icon then open from task bar instead of having it open whith start up.

Quote
Originally posted by cra_arc
after having problems with core centre reading various temps from 38c to 66c on start up !
think ive found a way to get it stable and sorted
just remove from windows start up ( using tweak-xp) and it has now booted at least ten times with a regular temp reading mid 40`s rising to 49 c
if it stays like that ill be happy !
just need to click on desktop icon then open from task bar instead of having it open whith start up.
u dont have to use tweak xp to remove core center from start up.
go to start
run
type 'msconfig' (without the ')
click on start up tab
untick core center
apply
close
I think ill be trying this trick when i get home tonight :D

Core Centre 5.8

hie , i am using the latest version of core centre
face this problem
1) NB Temp doesnt show
2) when i increase FSB, and click OK , the computer hang

Quote
Originally posted by Martel
Hi, All,
I face the same problem using 5.8, so i uninstall it and reinstall back the 1.5.5.0, problem seem solved...
Hi Martel,
do you think you could upload ver 1.5.5.0 somewhere so that I can pick it up?! I'm asking cause I hit the same problem with 1.5.8.0 but hadn't kept a copy of 1.5.5.0 to reinstall it.
Many Thanks

Core Centre Alerts - No Fans Installed

Ok, i've had a look around the forums and could see anything regarding this subject. It's doing my head in!
I run an over clocked system, spec is un-important however I am running a full water cooling system through the CPU and GPU. Consequently I don't need a lot in the way of fans, so I have a small fan controlled from the front panel to brush some cold air over the northbridge.
My problem is that when I boot my PC and Core Centre starts up, it immediately maximizes and starts beeping. Eveything is fine as far as settings I promise you, so the only thing it can be doing is warning about fan speeds - because there isn't any!
Has any one worked out how to stop it from doing this?

Just checked BIOS - couldn't see any option to stop monitoring any fans. Any thoughts, 865G Neo2 ?
Thanks for the suggestion on moving the fan. I didn't go into much detail regarding my system, but it was designed for power, but just as important; noise. I only really need the fan over the northbridge when i'm gaming, so I want to leave it on my external control so I can knock it right back when I don't need it.
Something else that i've just noticed is that on my normal partition which I use for most things, I've got a little app running at startup called startup guru. It allows you to alter the timing of the start up group of apps. I have core centre set to start up 5 minutes after bootup and it doesn't give any alerts.
However, in my games partition which has nothing running at all in the way of background apps other than core centre it starts immediately and starts to alert immediately. But even if I kill it off and restart it, it still starts to alert immediately.
I'm going to try startup guru on my games partition and see if it sorts it.

MSI K8 Neo - V2 with MSI Core Centre

My PC suddenly restarted when I run MSI Core Centre, I have re-install my Windows but it always happen ...
Does anybody here knows or had a problem like this ?
Notes :
My computer specification is MSI K8Neo V2, AMD Sempron (Palermo) 2800+, Corsair 512 MB DDR CL 2.5, Pixelview GeForce FX 5200 and Maxtor 80 GB SATA.

Quote from: agoezz on 30-November-06, 16:16:31
I have tried Nextsensor and it cool enough ... thanks.
yep it is, you are welcome

MSI Dual Core Centre 2.0.1.0 (Fan Speed ALARM)

Spec:
MSI P965 Neo F v2.0
Intel E6600 Core 2 Duo
XFX-Nvidia 7800gt 256
4 GB 800Mhz Ram
Hi guys,
Anyone here know why the following would happen:
I use the MSI Dual Core Centre 2.0.1.0 for Windows XP... every so once in a while, the fan speed would drop to 0-RPM, and
a very irratating alarm would go off. This started to worry me, and I opened my side panel to look at the CPU Fan when the alarm goes off.
the Fan is turning at high velocity, but the alarm still goes off. Is there something wrong with this software ? or am I doing something wrong.
One minute it reports 2005-RPM, then it just shows 0-RPM, and the alarm goes off. My machine is about 2 months old.
Should I be making changes in the BIOS on the Mobo, to enable support for Dual Core Centre???
Please help...very worried...
By the way "Speed Fan" reports no such alarms or CPU fan speed issues...
What is going on ?

Not sure if this may work bc you reported fanspeed reaching zero.
On my system with 975XPUE, Arctic Cooling Freezer 7 always runs below 1K rpm. So I have to use a user profile with Fan Min set about 833 rpm to avoid the annoying alarm.
If you don't find any solution to the reported fanspeed reaching zero, you might be able to at least disable the alarm by setting Fan Min in DCC to 0 rpm. That or uninstall DCC as suggested by most forum users.

Software core centre problem

Similar Messages

Maybe you are looking for