Software to install Airport Extreme Base Station

Hi all,
Any idea how I'd re-install the Airport Extreme Base Station? I lost the disk that came with it.
Thanks for your help,
Chelsea

chelsea_marti, Welcome to the discussion area!
There is no need to re-install anything. The "AirPort Admin Utility" and "AirPort Setup Assistant" are in the /Applications/Utilities folder on your Mac.

Similar Messages

  • HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
    Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
    As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
    Is there a way to resolve this issue?

  • I have an Apple AirPort Extreme Base Station (Simultanious Dual_Band) (MC340LL/A), and updated the software.  After updating no devices can connect via wifi.  Any suggestions.

    I have an Appl,e AirPort Extreme Base Station (Simultaneous Dual_Band( MC340LL/A.  After updating the software, no devices can connect via wifi.

    As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.

  • What is Error 2813 while trying to install  my Airport Extreme Base Station? and How can I fix it? Thanks

    What is Error 2813 while trying to install  my Airport Extreme Base Station(A1143/MA073LL/A)? and How can I fix it? Thanks

    Did you remember to completely power cycle the entire network?
    You would want to do this after any update or change to the network.
    If you did not do this yet......things are out of sequence.
    Power off everything on the network.....all devices.....power down order is not important
    Wait a few minutes
    Start the modem first and let it run a minute or two by itself
    Start the next device connected to the modem the same way
    Work your way out on the network starting each device about a minute apart
    Check the network

  • I have just purchased and installed a new Airport extreme base station but now the Airport Utility cannot see my old Airport Express. Are their compatibility issues and do I need to purchase a new Express?

    I have just purchased and installed a new Airport extreme base station but now the Airport Utility cannot see my old Airport Express. Are their compatibility issues and do I need to purchase a new Express?

    When you can, take a look at the old AirPort Express and locate the model number in the faint print on the side of the device.
    If you see A1084 or A1088, this is an older Express version that is no longer supported by the current version of AirPort Utility that you are using with the new AirPort Extreme.
    If that is the case, your Express is at least 6 years old...probably older...so it is about time to treat yourself to a new version with much faster speeds and more features.

  • New 10.3.9 install on Pismo G3, Airport Extreme Base Station Error Network

    My 10.3.9 Pismo laptop G3 with built in firewire ports worked perfect on my Airport Extreme Base Station — I just Erased and reinstalled 10.3.9 (it was working before I Erased this morning) and now my Original Airport card can't join my wireless network:
    *"There was an error Joining the Selected Network"*
    I zapped Pram, reset power manager successfully (date reverted).
    I accessed the AEBS by a 10.6.3 Mac Pro and checked the Equivalent Password "WPA Password: ####PW###"
    Radio Mode selected: 80211n (80211b/g compatible).
    APBS version current: 7.4.2
    G3 sees my network as expected.
    The APEBS hasn't changed (except for the recent update).
    I restarted the AEBS.
    Still get the error...HELP!
    I saw the exact problem on several archived threads, but no one gave a solution or explained the problem (and I'm going blind here).
    Again, for the past two years it was working fine with 10.3.9, it broke this morning after I erased and reinstalled 10.3.9.
    10.3.9 is the only software loaded on this laptop.

    If you just bought it I would recommend calling Apple, they can help you set it up.
    Also you should consider getting a high speed Internet connection. They are very inexpensive these days and would make your Internet experience much more enjoyable. Where you live I would think you have a choice of DSL (available from most telephone companies) or Cable, which would be the quickest but also more money too.
    Regards,
    Roger

  • Connect to Linksys Cable Gateway via AirPort Extreme Base Station?

    Thank you in advance for any replies.
    I have the following new setup:
    A G3 Blue tower running OS X 10.4.10 is successfully connected to the internet via a Linksys WCG200 Cable Gateway connected to RCN's cable internet service. The WCG200 unit has wireless capacity though it's connected to the G3 tower via ethernet cable.
    A second Mac (G3 iMac DV running OS X 10.4.10) is in another room in the office. I'd like to set it up with internet by wirelessly connecting with the existing WCG200 unit using an Airport Extreme Base Station (AEBS) I've recently acquired. To ensure a smooth process, I reset the AEBS to factory settings and installed the AEBS software (version 4.2) onto the iMac DV. Finally I plugged in the AEBS into the iMac DV using an ethernet cable plugged into the AEBS's WAN port (AirPort Admin Utility advised me to do so).
    That's the hardware configuration. Working out the software and configuration details is proving 'niggly'.
    First, I used the AirPort Setup Assistant to configure the AEBS. I told it to Set up a new Base Station, then to set it up as connecting to the internet using a Cable modem (the top option of two—the second was to set it up with internet through a LAN). I set up the name and passwords for the Base Station and had the utility configure the AEBS accordingly.
    No internet connection occurred. I tried using the Internet Connect utility in the Applications folder, but no button or visible option for connecting via AirPort appeared, as the Setup Guide indicated it should, only a button for a VPN appeared.
    I called Apple and asked whether it was even possible to connect to the internet using the AEBS talking wirelessly to the WCG200 unit. A tech told me it could be done by going into the AirPort Administration Utility, going into Configuration, clicking on the WDS tab and inputting the MAC address for the WCG200 unit, then going into the Airport tab and typing in the channel that the WCG200 is using. Note that the WCG200 unit has 3 MAC addresses listed; one each for “modem MAC address,” “WAN-MAN MAC address,” and “WAN-DATA MAC address”. I used the “modem MAC address.
    The Apple tech added that it might need further tweaking, but that Apple couldn’t provide this tweaking and that I might check various forums if need be.
    I followed the Tech’s advice, at which point the utility informed me that it couldn't use DHCP or NAT with this setup’ and to make sure that the "Distribute IP Addresses" checkbox was deselected under the Internet tab. This I did, but it was already deselected. I told the utility to update the AEBS accordingly, and restarted everything, including the 2 Macs and the WCG200.
    Result:
    No connection.
    Tried it again with the Ethernet plugged into the AEBSs LAN port, still no connection.
    Help! Can’t I get the AEBS to even see the WCG200? I know wireless is properly functioning in the WCG200 because another user with a Windows laptop connects to it wirelessly. The Mac Tech also mentioned that this could be relatively easy with an AirPort Express piece of hardware (Card? Base station?) but that it would be difficult with the Airport Extreme Base Station.
    At this point we’re willing to spend $100 on getting this up. What would be our best option in terms of equipment, or can connectivity be accomplished with what we have?
    Thanks again,
    skyheart

    skyheart, Welcome to the discussion area!
    In theory using WDS would provide what you need.
    In reality the Linksys device is not compatible with Apple's WDS and therefore this will not work.

  • Windoze Ad-hoc networks killing Airport Extreme Base Station

    After having a horrible experience with an Orinoco base station sometime ago at his coffee shop, a client of mine asked me to install a new Wi-Fi access point to replace it. Since I'd never had a problem with my graphite Airport Base Station, I selected recommended that he try the Airport Extreme. Everything was been fine for over a year and half, with only the occasional interference problem, and even that easily fixed by a restart on the base station. Lately that has changed. We're in Baton Rouge, and since Hurricane Katrina, our population in our city has doubled (that's not an exaggeration), and the number of customers using the network in his coffee shop has increased as well - although it's still well below the maximum. The problem is that there are is large number of students from Loyola, UNO and Tulane who are now attending LSU, right across the street. And a significant fraction of those have ad-hoc networks set up on their Windoze notebooks, apparently unintentionally. When they come into the coffee shop their ad-hoc networks seems to cause the Airport Extreme to die, and not recover, until it is reset. This happens many times per day, sometimes more than once in an hour.
    It had been configured to automatically select a channel, but I re-configured to use a specific channel (and have been experimenting with the particular channel). It seems to reduce the problem for a time, but then we'll have the problem back in force within a few days.
    I have verified (using iStumbler) that there are no other "managed" networks near-by, and I have noticed that the problem ALWAYS happens when there is are ad-hoc networks, and after politely asking customers if I can check their settings, (it's scary how many people will let you poke around on their computer, if you seem like you know what you're doing) I've also seen compelling evidence that it is Windoze users, not Mac users, who tend to cause the problem. Incidentally at this particular coffee shop the Windoze:Mac ration is something like 60:40. What can I say, it attracts discerning customers. Since some of them have "lsuwireless" set up as an ad-hoc network (and as I said, LSU is across the street), my guess is that somehow these get set up, not on purpose, but accidentally, while trying to connect to the university's wireless network. Apparently the process is not so straight forward for Windoze users as for Mac users.
    I have upgraded the Airport Base Station software to the latest available as of last week. Though I don't have that version number available at the moment.
    So I have several questions:
    1) Is this really the same radio interference problem that I've read about elsewhere on this discussion board?
    2) Would an external antenna on the base station help? How about a powered one?
    3) Aside from "Use Interference Robustness" and trying different channels, is there some configuration setting that I might be missing that could enhance the base station's reliability?
    4) Does anyone have a suggestion for a permanent fix - preferably without switching to a different access point, although at this point, that's a viable alternative. After a year and a half of stable operation though, we're loathe to switch again unless it can't be avoided, because the Orinoco access point we used before had behaved exactly like this, but even worse, and without necessarily having ad-hoc networks being present to cause the problem.
    5) Failing any other good solution, can anyone suggest a way to determine which computers are causing the problem without having to interrupt each customer to poke around on his computer?

    I have an Intel based iMac and a MacBook Pro. Both
    are (well until tonight) connected to the internet
    wirelessly through the Airport Extreme Base station.
    I've had no trouble up until now. Tonight for some
    odd reason the MacBook Pro Airport card fails to
    detect the Airport Extreme Base Station. It detects
    OTHER wireless networks around the building, just
    not the one it's supposed to connect to. Opening up
    Airport Utility doesn't even show the Airport
    Extreme Base Station being present. I know the Base
    Station is not at fault - it works fine with the
    iMac. Tried setting the Sharing mode on but that
    didn't help either (not that I changed any of the
    settings to begin with).
    Can anyone help? I'm really at a loss here.
    Any one? Any suggestions?

  • Airport Extreme Base Station as bridge for Westell DSL router

    I have searched the forums & internet and for the life of me cannot get my network to work properly! I hope you can help.
    Here is the situation (I rent so chances are we will not be moving hardware anywhere):
    - Westell (Verizon) DSL wireless router downstairs connected to the internet, 1 iMac via ethernet, and 2 ibooks via Airport cards
    - One lonely Powermac G4 upstairs that does not have a wireless card
    - One extra Airport Extreme Base Station with firmware version 5.7 installed & connected via ethernet/LAN to the G4
    I figured the "easy" thing to do would be to use the AEBS as a wireless bridge to get the G4 online. The network utility has occasionally thought that the G4 was connected to the internet, but the internet didn't work at all when it said that!
    I have been configuring the AEBS using my wireless ibook (G3). I "unchecked" distribute IP addresses, and "checked" connect to network via WDS. I used the Westell's MAC address as the main WDS source. Under the "WDS" tab, I said to configure the AEBS as a remote station and the Westell router as the main station, and to allow wireless users to connect.
    I have tried using the same Network name for each. WEP/WAP is NOT set up on either modem, so passwords aren't a problem. They are both set to channel 6. I am configuring the TCP/IP settings manually.
    When the network names are the same, the internet either stops working, or the computers can't find the AEBS.
    I don't understand why the AEBS seems unable to see the DSL network.

    Hi,
    Well, what I have been able to do is this:
    I have a Westell Wireless DSL router, just like the one mentioned here, and just like the one mentioned in the article I made reference to, the one started by Mr. Müller.
    As was mentioned in the Mr. Müller article, there are some possibilities that will work. They were submitted by a guy named Duane, from Texas. He gives three alternate possibilities, which he entitled "Solution #1, Solution #2, and Solution #3. He says all three of these alternatives will work, and in reading them over I came to the following conclusions: First, he really knows his stuff, and second, his proposed solutions would probably work.
    Based on his comments I decided to take a risk yesterday - I put my older Mac Base Station in a drawer and invested in a new Airport Extreme.
    Anyway, I digress...
    What I've done is follow Solution #3. And it works! I now have a connection from my laptop to the Airport Extreme base station and the internet. I am typing this message using that connection. All I had to do was disable the wireless connection of the DSL router (using their software, of course), and connect the Airport Extreme, via the LAN Ethernet connector, to the Westel DSL router.
    Now, all that remains for me is to extend the range of the base station, using an Airport Express. I haven't had any success with that yet, but I see no reason why I shouldn't get it to work eventually. If you can help me out with that, though, I'd sure appreciate it.
    Best regards,
    Patrick
    Macintosh G5, Powerbook G4   Mac OS X (10.4.7)  

  • Recovering Old Datas on New Drive + Setting Airport Extreme Base Station old and new ones

    Hello All,
    Situation:
    -iMac 24" Alu/2008/2.8 Ghz Intel Core 2 Duo/ 2Go DDR2 SDRAM
    -2 Airport Extreme Base Stations mushroom type,
    -1 Airport Extreme Capsule Model: A1143
    The original 320 Go Hard Drive of my iMac crashed few months ago. A "technician" installed a new Hard Drive 235 Go while trying to recover all datas from old one. Failed.
    No back up. The old disc needs to be unlocked in a dustless atmosphere. Quite expensive at the moment.
    I decided to install OS X from sratch with the original Install Disc delivered with my iMac.
    OS X is 10.5
    Once on line I updated all pre-installed softwares. Among which Aiport Utility 5.6.1 today.
    Problem:
    I would like to get bigger hard drive disc, 1To for example. Does this still exist for this iMac 2008 Alu ?
    How can I do to get my iMac again to OS X 10.9 ?. Does this mean I need to buy all intermediate levels again ?
    How do I get my softwares (the ones on the original Disc: Pack office, Pages, Numbers, etc ...) back on track again, since my iMac is now more like down to factory level ?
    Extending my internet provider from the WiFi router via my 3 Airport Extreme Base Stations: 2 mushroom type that need OS X + Airport Utility softwares at a certain level, while the Capsule might need another level. Right now I tried to set up the 3 of them with this Aiport Utility and though they all recognize the provider network, I can never conclude to extend it with the Base Stations: it drops the case. (WDS trouble which I don't even know what it is, or the Base Station simply desapears from Airport Utility scan, ...)
    Thank you all for you attention.
    Your comments are welcome especially if you have any knowledge on these various subject.
    Can't wait to read your piece of advice.
    Lionnel From Paris (France).

    me too... i connected my hard drive with all my music but i cannot see any of the music that used to be in my itunes... i checked and its there (when I connect the HD directly to my computer) but not when is plugged into the Airport Extreme... Please help!

  • Cannot see Airport Extreme Base Station--Watch for 2.4Ghz traffic!

    (Issue is addressed in the body of this post)
    Great when working on 802.11n at 5Ghz, BUT...
    If you have to be compatible with 802b/g you are forced to transmit at 2.4Ghz. Traffic at this frequency can be so bad that it made my station invisible (even with "Interface Robustness" activated). The "automatic channel selector" is supposed to choose a clutter free channel for clear communications, but it does not work well. I had to reprogram the station (through ethernet) to manually change the channel to a more stable one. In my case, channel 8 did the job.
    After this, the Airport base worked perfectly!
    I live in a condo area where I get 8 strong wireless networks, all at the same time. Add microwave ovens, TV's and cordless phones and you get a jammed 2.4Ghz highway. Make sure to select a channel that provides seagway to the "carpooling lane".

    Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
    Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
    Any help would be greatly appreciated.

  • Airport Utility does not see Airport Extreme Base Station

    Purchased Airport Extreme yesterday at Apple Store to replace old Netgear Router. Wanted wireless network to work with 2 identical HP Laptops running XP with SP3 and 2 iPod touches, and possible future purchases of iPad 2 and Apple TV. Installed Airport Utility software from CD on Dell Studio running Windows 7. Connected Airport Extreme to cable modem and Dell Studio. Ran Airport Utility software to configure Base Station but it did not recognize the Base Station. Base Station had blinking amber light. Did have internet connectivity on Dell Studio, and wireless internet connectivity on 2 iPod touches, and on one HP Laptop. No wireless internet on other HP Laptop. But wireless internet connection was unsecured and Airport Utility did not see Airport Extreme so could not configure it to make it secure. Contacted Apple Customer support. After 30-40 minutes of attempting several different possible fixes only able to use Airport Utility to configure Airport Extreme remotely, wirelessly, from one HP Laptop, not the Dell Studio that is directly connected to the base station. Now that the base station is configured the network is secure. However, second HP Laptop cannot connect to primary wireless network. I created password protected "Guest" network using Airport Utility, and laptop is able to connect to this Guest network. From reviewing forums am now able to configure Airport Extreme with Airport Utility by using "Configure other" on Dell computer. But utility cannot find device by scanning. Would like to find way to (1) have Airport Utility on Windows 7 Dell see Airport Extreme by scanning and not using "configure other," and (2) have 2nd HP Laptop connect to primary network and not "guest' network. Any assistance would be greatly appreciated. Thanks.

    Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
    Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
    Any help would be greatly appreciated.

  • Macbook does not see airport extreme base station

    Hi
    I set up my airport extreme several years ago.  I recently noticed that, under "security," the guest network says "WPA2 secured," but the main network says "none."  Is this a problem; i.e., does the main network lack security?  Further, when I open the airport utility, it cannot find a base station.
    What am I doing wrong?
    Thank you!
    ron

    Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
    Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
    Any help would be greatly appreciated.

  • IMac does not see Airport Extreme Base Station wirelessly

    Trying to use my existing PC hooked up to Airport Extreme BS via ethernet cable, which works fine. I then open Airport Utility on my iMac and it scans for wireless devices but it can't see the AEBS (located beside it). Opening Base Station tab and there are no solid headers to click on, just the soft grey headers. I am fairly new to Apple product so if I've left any info out to further troubleshoot please let me know.
    Eventually I would like to connect my Apple TV, located downstairs, wirelessly as well as use an Airport Express (wirelessly) to boost the signal if need be due to concrete walls and floors in construction of house.
    I have OS X Version 10.5.8 (up to date), Intel, Airport Extreme Wireless Card.
    Thanks for any help out there.

    Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
    Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
    Any help would be greatly appreciated.

  • Airport Extreme Base Station and Win 2000

    I have a new Airport Extreme Base Station. All is well with my Mac but my company laptop uses Windows 2000 Pro. The software that came with my AEBS will not install I get an error that I can not install as Win XP SP2 is required. Anyone got a work around or know where I can find compatable software?

    All,
    I recently posted what I believe to be a similar/identical issue. See my post here: http://discussions.apple.com/thread.jspa?threadID=1378849
    I have not changed my AEBS to "Off (Bridge Mode)" yet, because everything currently 'works' but I continue to get the occasional "Double NAT" warning suggesting I switch the AEBS to bridge mode. When this happens, I lose connection to the internet and need to unplugged both the AEBS and my modem to re-establish a connection to the internet and the external HD I have connected to the AEBS.
    My question for Jmiller1138, do you continue to get the "Double NAT" warning even when you changed your AEBS to "Off (Bridge Mode)"? I am hesitant to change my AEBS to bridge mode since I'm assuming I'll need to totally reconfigure my entire network (meaning both the AirPort Extremes, my wireless HP printer, and my firewalls on my PCs).
    The ignoring of the warning (i.e. closing the AirPort Utility without updating the AEBS) is what triggers the need to reset my AEBS and modem. Not fun.
    I guess I'll just need to bite the bullet and set the AEBS to bridge mode . . . yes?

Maybe you are looking for