Solar_project_admin dynamic authorization??

Hi friends,
I have 4 projects.I dont want to authorize one by one for my projects. I want to process single role .
I use S_PROJECT role. This role have project name field . Do I use as dynamic this field.
Thanks for your answers.

Using S_PROJECT you can identify a specific project name, or you can use the (*) to denote ALL projects.
Does this answer you question?

Similar Messages

ISE 1.2 - Dynamic Authorization Failed

Hello!
In my design network I use the ISE for CWA with a WLC, but when a client entrer his credentials, the CoA failed with this error : "11213 No response received from Network Access Device after sending a Dynamic Authorization request"
This error is really strange because I can contact the ISE from the WLC. My ISE, and my broadcasted network are in the same VLAN, is it possible that this error come from this network architecture?
My is is patched with the cumulative patch 7 and for information, I can do a "manual CoA" by disconnect/reconnect the client manually and after that the client has a network access.
Used configuration for ISE and WLC : http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/116087-configure-cwa-wlc-ise-00.html
Thanks in advance if you have the least clue to resolve this issue.
Kévin

I will perform some additional testing and let you know my results. I have this setup in the lab now with ISE 1.2 Patch 7 as well.... Since I only have a couple of PC's in the lab, I've noticed that I am unable to terminate the users session manually. So I usually end up stopping and restarting the services. This is how i clear my live sessions.
Is your setup in a Lab or Production? If its in a lab can you restart ISE and your WLC. I know when I first did my "debug client <mac>" My airespace ACL was showing the incorrect ACL ID. After a reboot of ISE and recreating my WLC ACL it went away. I haven't noticed my service IP ever showing up in ISE. I usually see the users MAC address then a [email protected] "User Authentication" with his IP. Next its the WLC MNGT Interface and finally the User Authorization again show Authz Internet-Only.
My lab does not always function 100% so I am hoping after we go Live this weekend, these flaky issues go away. One of my problems is I don't have internet access. Just a web server hosting a web page. I'll keep notes on anything I find that hopefully assist you.

ISE Alarm (WARNING): Dynamic Authorization Failed for Device

Hi all,
I am posting this discussion as previous posts that I have found in this forum have never been resolved or the resolution is not applicable to me.
I am using ISE 1.1.1.268 and WLC 7.2.111.3 and NAC agent version 4.9.1.6 on Windows 7 Client machines.
About once a day i get the error "ISE Alarm (WARNING): Dynamic Authorization Failed for Device".
The device it is reffering to is my NAD, a WLC 5508 running 7.2.111.3
I have looked at the logs and I cannot see anything in the logs which correcponds to this message so that I can troubleshoot further. Maybe I can if I am enabling the correct logging level on the correct ISE component.
Can someone suggest the components and the logging level that I should set to get some more detail about this error?
At the moment, I have only set debug logging on Active Directory. I have TRACE logging set on Posture, Runtime AAA & prrt-JNI.
I do not want to enable too much debug logs, so I was wondering whether anyone can help with a specific element that I should be debugging.
I thought debugging the posture element would be enough but when I look at the logs there is nothing there that relates to this message.
Can anyone help?
thanks
Mario

Firstly, I wouldn't run a production deployment of ISE on 1.1.1.... 1.1.3 Patch 1 or 1.1.4 is the way to go.
Secondly, this error happen a lot, especially with Wireless, and it's not worth worrying about. I've had a couple of TAC cases opened for this and some similar errors, generally they're caused by a Client going to sleep, leaving the coverage area or otherwise leaving the WLC while ISE is trying to do something with it.
Only worry if you actually have a Client-impacting problem, which by the sounds of it, you don't.

ISE: Dynamic Authorization Failed

Hi,
I am gettning warning messages in ISE saying
Cause:
Dynamic Authorization Failed for Device: 0002SWC003 (switch)
Details:
Dynamic Authorization Failed
It is not only on that switch but on all switches I have configured. I am using 3560 IPBase 12.2(55)SE6. I have configured them according to Trustsec 2.1.
My end devices are none-802.1x.
I can't figure out what is causing this error.
The thing is that I have not experienced any problem. In Live Authentications there are some 'Unknown' and 'Profiled' devices hitting the DenyAccess rule, but other then that everying is beeing Authorized fine.
Anyone got an idea what could be causing this error?
Regards,
Philip

This is what I have found out.. Using ISE Version 1.1.1.268. If you go the logs page
Jan 10,13 7:39:12.147 AM
Dynamic Authorization failed
and then go to the details...
Failure Reason > Authentication Failure Code Lookup
Failure Reason :
11213 No response received from Network Access Device
Generated on:January 10, 2013 8:08:17 AM PST
Description
No response received from Network Access Device.
Resolution Steps
Check the connectivity between ISE and Network Access Device. Ensure that ISE is defined as Dynamic Authorization Client on Network Access Device and that CoA is supported on device.
...next check into Resolution Steps...

5417 Dynamic Authorization failed

Hi guys,
Does anyone meet this Radius Error in Cisco ISE 1.2 and the switch 2960 12.2(55)SE7 ?
When i reauthentication the guest profile to the other profile using Radius CoA on the Self-Service Guest Workflow.
The error is :
Event
5417 Dynamic Authorization failed
Failure Reason
11103 RADIUS-Client encountered error during processing flow
Resolution
Do the following: 1) Verify shared secret matches on the ISE Server and corresponding AAA Client, External AAA Server or External RADIUS Token Server. 2) Check the AAA Client or External Server for hardware problems. 3) Check the network devices that connect the AAA peer to ISE for hardware problems. 4) Check whether the network device or AAA Client has any known RADIUS compatibility issues.
Root cause
RADIUS-Client encountered an error during processing flow
I checked all the resolution steps but the error sitll exsit.
I would greatly appreciate any help you can give me in working this problem

An internal error has been detected during the processing of an incoming RADIUS packet. Make sure that the client device is compatible with AD Agent, has been configured properly, and is functioning properly. Make sure that the same RADIUS shared secret has been properly configured, both in the client device and in AD Agent.
http://www.cisco.com/c/en/us/td/docs/security/ibf/setup_guide/ad_agent_setup_guide/ibf10_log_msgs.html

Dynamic Authorization Failed

hi
I keep getting error meesages on the ISE in regards to RADIUS
the error is
Dynamic Authorization failed : 1213 No response received from Network Access Device
i am using ISE version 1.1.1 and the NAD is a WLC running version 7.0.98.0
i use ISE to authenticate users via PEAP. I deleted the NAD and re-added it twice but i still keep getting this issue. this set up was working fine for the last few weeks.
i dont think location and device type would cause an issue to authentication under the NAD list
anyone have any ideas?

the option i.e drop down box wasnt there. lookin at the compatibility chart of ISE 1.1.1 and WLC, minimum version for WLC is 7.2.103.0
Do you need to have RADIUS NAC enabled if the ISE is only used to authenticate corporate wireless users against AD. there is no CoA,
the other function is to use RADIUS as network management logon. to WLC using the AD. depending on the AD group , one could get priv 15 or priv 5 access. i am also using device attribute by location so that remote offices network enigineer cannot log onto the WLC. i.e i created a NAD , put it in a location and use that location AND the AD group to qualify for priv 15 access.
Coudl this policy interrupt the wireless RADIUS policy? Wireless policy is at the top of the list under authorization tab.

Dynamic Authorization Failed: DiconnectNAK

I have WLC 7.6 and ISE 1.2 Patch 6.
My use case is WLAN Guest Access with CWA. I have ISE Appliance 3395 (2 Admin/Mon, 2 PSN). Everything work fine so far.
But from time to time I get these strange message (it does not matter if I do a manual Session termination in the Operations Tab) Everything is configured in the right way, since normal CWA works (CoA is working fine, but not always...).
Here the corresponding Log-Entry:
0000001241 2 0 2014-02-28 11:11:37.241 +01:00 0000106595 5417 NOTICE Dynamic-Authorization: Dynamic Authorization failed, ConfigVersionId=53, Device IP Address=a.b.c.d, Device Port=42121, DestinationIPAddress=a.b.c.d, DestinationPort=1700, RadiusPacketType=DisconnectRequest, Protocol=Radius, RequestLatency=3, NetworkDeviceName=xx-WLC01, NAS-IP-Address=172.16.226.26, Calling-Station-ID=1C:AB:A7:96:7B:99, Acct-Session-Id=53105c2a/1c:ab:a7:96:7b:99/336136, Acct-Terminate-Cause=Admin Reset, Event-Timestamp=1393582297, cisco-av-pair=audit-session-id=ac10e21a00052f6953105f07, AcsSessionID=ise-04/182359788/9392, Step=11044, Step=11017, Step=11100, Step=11101, Step=11048, NetworkDeviceGroups=Location#All Locations#xx_VPN, NetworkDeviceGroups=Device Type#All Device Types#Wireless Devices#WLC Foreign, CPMSessionID=ac10e21a00052f6953105f07, EndPointMACAddress=1C-AB-A7-96-7B-99, Location=Location#All Locations#xx_VPN,
Has anybody ever had the same expirence, or is this a know issue?
Thanks for feedback!

Please go through the link below for best practice.
http://www.redelijkheid.com/blog/2013/4/2/cisco-ise-change-of-authorization-coa-not-working

Dynamic Authorization Failed - Posture with Guest Portal - ISE - WLC

Hello everybody,
I'm implementing a NAC solution based on Cisco ISE. Unfortunately, I'm facing a problem related to the CoA (Change of Authorization).
The guest can authenticate successfully via portal and then he is redirected to the page of client provisioning.
When he is compliant with the policy he gets access without any problem and this means that CoA works perfectly. The issue occurs when he has to remediate (download the file from ISE and install it). In this case, we need a change of authorization profile.
The authentication logs show that the posture status changed from non-compliant to compliant but the users doesn't obtain access .
Here are details :
Authentication Details
Source Timestamp
2015-04-30 18:43:13.179
Received Timestamp
2015-04-30 18:43:13.18
Policy Server
ISE-CISCO
Event
5417 Dynamic Authorization failed
Failure Reason
11213 No response received from Network Access Device after sending a Dynamic Authorization request
Resolution
Check the connectivity between ISE and Network Access Device. Ensure that ISE is defined as Dynamic Authorization Client on Network Access Device and that CoA is supported on device.
Root cause
No response received from Network Access Device after sending a Dynamic Authorization request
Username
User Type
Endpoint Id
E0:9D:31:07:**:**
Endpoint Profile
IP Address
Identity Store
Identity Group
Audit Session Id
ca0019ac00000003ae674255
Authentication Method
Authentication Protocol
Service Type
Network Device
WLC-1
Device Type
Location
NAS IP Address
172.25.0.202
NAS Port Id
NAS Port Type
Authorization Profile
Posture Status
Compliant
Security Group
Response Time
15002
Other Attributes
ConfigVersionId
4
RadiusPacketType
CoARequest
Event-Timestamp
1430415778
AcsSessionID
50149c2f-08fb-4f9d-b1b5-f655e71d039f
StepLatency
3=15001
Device IP Address
172.25.0.202
CiscoAVPair
subscriber:command=reauthenticate
audit-session-id
ca0019ac00000003ae674255
Session Events
2015-04-30 18:43:13.18
Dynamic Authorization failed
2015-04-30 18:41:44.159
Dynamic Authorization failed
2015-04-30 18:35:42.64
Guest Authentication Passed
2015-04-30 18:34:39.214
RADIUS Accounting start request

You can use LWA for this . he WLC redirects the HTTP traffic to an internal or external server where the user is prompted to authenticate. The WLC then fetches the credentials (sent back via an HTTP GET request in the case of external server) and makes a RADIUS authentication. In the case of a guest user, an external server (such as Identity Service Engine (ISE) or NAC Guest Server (NGS)) is required as the portal provides features such as device registering and self-provisioning.
Refer to the following link for configuration example
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml

Dynamic authorization in Integration Gateway with SMP 3.0.3

Hi All,
we have SAP ECC as backend system, we created service in ECC and added service in gateway cockpit. Now i can get the data from backend ECC using gateway cockpit URL.
My doubt is
While creating destination for ECC in SMP Gateway Cockpit, we have to give credentials for basic authentication. While calling service of SMP Gateway Cockpit , It is going to ECC with the user name given in Gateway Cockpit and giving the data authorized by same,
How to make the dynamic authorization.
Thanks
Suresh
Tags edited by: Jitendra Kansal (Moderator)

suresh babu
I followed the steps mentioned by you.
1. Added a HTTP/HTTPS authentication provider to "SAP" security provider.
https://sapes1.sapdevcenter.com:443/sap/iwbep?sap-client=520
2. In the gateway cockpit. modified the destination details:
3. When i open service document, there is no pop-up. Did i miss something i between?
Regards,
JK

Dynamic Authorization in Analysis Authorization

Hi All,
We are planning to migrate 3.x Authorization Migration to Analsysis Authorization. We have implemeneted Dynamic Authorization
concept which is using Customer Exit Variable. Now Kindly Guide me how I can retain the the same Dynamic Authorization Concept in New Analysis Authorization.
Regards,
Amit

Hi Amit,
Below article will helpful:
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/f0f9f33c-0f17-2d10-d3a2-ae52ccd00780?QuickLink=index&overridelayout=true
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/90f762d1-538b-2d10-1695-899a8bb165df?QuickLink=index&overridelayout=true
Hope this helps!
Amandeep Sharma

Dynamic Authorization VDSK1 Values?

Hello,
I was wondering if there is a way i can get some of the authorization values (e.g. org unit in HR) dynamically without specifically giving these values in the authorization Object P_ORIGIN, vield VDSK1?
there is a lot of users with different access depending on their org key, and it is not reasonable to create 30 or 50 roles just for them to be able to access system ?
I hope there is a solution for this. thank you all in advance.
regards,
Mo A

Thanks,
but could you tell me how ? This is first time i read bout structural authorization and i read a document on how to use it but it seems there is something missing which is giving that "Failed HR Structure Authorization".
what i did is as follows and if there is something missing or done wrong please comment on that:
1. Maintain structural authorization profile in view T77PR
2. Assign structure authorization profile to user in view T77UA.
thats all i did ? is there more steps or configuration to be done beside the above 2 steps, please advise ?
Regards,
Mo A

Not able to decide on : Mission Configurable Authorization

Hello,
I post here after begging people to
please understand my problem first.this is what I need to achieve:
It is about dynamic authorization.
My application will have an admin page where the admin will be able to give access rights to users for certain actions on certain pages. these could be any permutation and combination.
I need to be able to authorize them based on this condition.
For example :
If it were a mechanic application.
The admin will be able to authorize MechA to be able to perform "Add, Delete" actions on garage A, but only VIEW rights on garage B.
similarly MechB to be able to only "ADD" in garage A, but ADD,DELETE in garageB.Again, the number of garages can be many. the admin will be able to add a garage and delete a garage.
(ofcourse, based on the current access rights they have, the JSP will display those current access rights)
I have poured over google search and forums and security frameworks to decide on an approach for this.
I initially had thought that I will have a table which will have two cols USER and PERMISSIONS.
where users would be the suers and permissions would be URLs. Ex. :
mechA | garageA/add.jsp
mechA | garageA/delete.jsp
mechA | garageb/view.jsp
However, this premature understanding will not work because of obvious reasons (if I need to update or delete the URL for the user.. I am screwing up everything).
Then, now I am thinking of an XML based authorization now. where the parent node will be the user name and his child nodes will be the URLs he has access to. Though i have not worked on this, I know this will be of no use, because my application will have the capability to switch between a db and LDAP. I have very little knowledge of LDAP though.
No secuirty framework is going to be of help ( i have looked extensively through JAAS and Acegi).
because they function majorly on ROLES. In my case I have no ROLES at all :-(
I have been pulling my hair out trying for a solution for this kind of a configurable scenario, where the user base could be on a DB and on LDAP.
Any ideas/help/pointers towards an approach would be highly appreciated.
thanks in advance for your time.

If you don't have roles now, rethink your design.
What if another mechanic comes in as a replacement
for an existing mechanic who left or goes on holiday?
Do you really want to have to assign all permissions
to the new mechanic again? No, you want to be able to
say: this new mechanic has the same role(s) as the
original mechanic and be done with it. Or what if a
mechanic gets promoted? Instead of having to add and
remove all the accompanying permissions, just set or
add the new roles.Well, there will also be Groups, to which the mechanics can be assigned, but it is not a necessity for them to be under a group.
A mechanic can be an individual with individual rights, or can be a part of a group which has certain permissions. In my case, everything needs to be highly configurable. Creating a single user(with specific permissions) or creating the group(with specific permissions) and then assigning mechanics to the group, will really be the admins choice, who will set the users up.
If you realy, really, really can't think of any roles
that make sense, you can pretend each mechanic
defines his own special role (the role is the same as
the mechanic) and still use those frameworks.hmmm... I have typically assigned URLS with wildcard chars. like /admin/*.* with ROLE_ADMIN thing.
In this case,I will probably have to have many relative URLS mapped with a singular ROLE. However, how I can change/update these URLs based on the admins input, still remains a mystery to me.
Any other suggestions ?

WLC, FlexConnect, ISE: Dynamic VLAN not working

Hi,
Not sure if this is a WLC or ISE problem, but since I am unsure of the WLC config I will try here first.
Equipment:
WiSM2 7.2.111.3
ISE 1.1.1.268
AP 3502 in FlexConnect
What I want to achive:
One SSID, multiple VLAN
Devices gets profiled in ISE and based on type of device it gets asigned to a VLAN
Problem:
When the device connects the first time it ends up in native VLAN and not switched to the right VLAN, but when I reconnect then it is added to the right VLAN.
WLC config (I know you like images so here you go ):
I must be missing something but I can't figure out what. I will be attaching a debug aaa event enable for when the client connect the first time.
In ISE I have an Authorization Profile that just say VLAN ID/Tag 158 (the VLAN that the device should go to) an it is added to the Authorization rule of the profiled device. CoA is set to Reauth.
When the client connects I get three events in ISE:
1.
Authentication failed :
22056 Subject not found in the applicable identity store(s)
2. Authentication Success. With the results:
UserName=00:18:DE:A2:BC:3A
User-Name=00-18-DE-A2-BC-3A
State=ReauthSession:c20e8b2f0000027e50ed27f8
Class=CACS:c20e8b2f0000027e50ed27f8:ISE01/144259326/671335
Termination-Action=RADIUS-Request
Tunnel-Type=(tag=1) VLAN
Tunnel-Medium-Type=(tag=1) 802
Tunnel-Private-Group-ID=(tag=1) 158
cisco-av-pair=profile-name=AX-Intel-Device
3.
Dynamic Authorization failed :
11213 No response received from Network Access Device
Has anyone got this to work? Do I need to add FlexConnect groups? If so then why?
Regards,
Philip

I think you're hitting CSCua58554
The bugtoolkit description is horrible.... From what I recall when I ran into it, I believe that Flex connect is having a problem with Mac filtering based AAA override on open wlans (and/or CWA based). In general, AAA override works fine when it is from like an eap authentication.
We had to use a 7.3 ES to resolve it.....
Looks like it is implemented in 7.4 though..... If you dont want to join the 7.4 bandwagon quite yet, you might could ask TAC for an ES of 7.3, don't think they have a 7.2 build.

Authorization by Sales Employee

Hi All,
I have one report called Sales by Sales man. this report has to view by specific sales employee by his/her actual sales and target sales.
He/She should not able to see others data. only he/she able to see his/her data only.
How do i achieve this. i know this is something to deal with Authorization.
Can somebody help me on this.
Thanks
Prerana

Hi,
Please examine these articles. You may be need to create dynamic authorization which I gave second link.
1.
http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/101fb4f5-eb7c-2c10-5daa-b479c47f0a14
2.
http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/b0b3fb3f-a21c-2e10-3a9c-efc3e59996a8

Can't set authorizations

Hi folks,
We're facing serious problems when trying to set authorizations to users.
We can't set any authorization. Everytime we open the General Authorizations form, we change all the authorizations we want.
When we press Update, nothing happens. Then, we press update again, and the message: Operation completed sucessfully appears.
We click on OK, expecting the authorization worked. But if we open the form again, no changes were made.
We've tried stopping all add-ons and there's nothing in SBO_Transaction_Notification.
Any ideas?
Thanks in advance!

I run this query that solved the problem:
--Select Query with description:
--to detect report objects are used in dynamic authorization but doesn't exist in report object master data
select * from CDPM where ObjectType = 232 and ObjectKey not in (select doccode from rdoc) order by permid
-- to detect permission are used in user preference but doesn' exist in dynamic authorization or user defined authorization
Select * from USR3 where PermId
not in (Select distinct Absid from OUPT union Select distinct cast(PermId as nvarchar(50) )from CDPM)
----Update Query with description:
----to delete report objects are used in dynamic authorization but doesn't exist in report object master data
--delete from CDPM where ObjectType = 232 and ObjectKey not in
--(select doccode from rdoc)
-- -- to delete permission are used in user preference but doesn' exist in dynamic authorization or user defined authorization
--Delete from USR3 where PermId
--not in (Select distinct Absid from OUPT union Select distinct
--cast(PermId as nvarchar(50) )from CDPM)

Solar_project_admin dynamic authorization??

Similar Messages

Maybe you are looking for