Solaris 10 AMD Installer

Hi,
This may have been asked already but i searched the forums and couldnt see if it was or not.
Anyway i was looking to deploy Weblogic on a Solaris 10 box but it is not Sparc it is an AMD processor.
Can anyone tell me if there is such an installer? Or if there is a workaround for the Sparc installer.
Regards,
Diarmaid

A similar question was asked in the below post,
Re: Weblogc 10.3 64 bit
But you can find what you are looking for at the following support page, there's what looks to be a basic/general installer:
http://e-docs.bea.com/platform/suppconfigs/configs/solaris/solaris10_103.html#102349
I'm trying to install 10.3 on Solaris 10 with an AMD64 now and I hit a Fatal Error when it tried to create the domain.
Hope that helps.
Edited by: user10882084 on Feb 18, 2009 8:19 AM

Similar Messages

  • [Solaris 10] Installation problem on nForce4 Ultra - SATA II - raid 0

    hi,
    Like I was read on HW web page, Solaris 10 should work fine with 'nForce4' (without 'Ultra'),
    but on mine mainboard (nForce4 Ultra) instalator was unable to found my array.
    I have ASUS A8N-E (nForce4 Ultra) with 2x 250GB Seagate on SATA II RAID 0.
    Is it posible to install this OS on 'nForce4 Ultra' or maybe I am doing sth wrong ?

    Hi, I have the similiar problems on Solaris 10 installation.
    I have a Compaq SR1710 AMD Sempron™ + 1GB RAM. I am trying make it a mini workstation.
    However, the installation was never able to throught.
    It always stop or freeze on the "dos" screen after I select "interactive" installation.
    The last error message I got was something "Skipped rtls01" something.
    I am trying to install Solaris 9 now, so far on disc 2.
    Very smooth. No problem..
    hope someone can give me advise on how to install version 10 on the machine.
    BTW, I checked teh HCL. It seems ok, given my machine is very basic.

  • Solaris 8 installation problem on an Intel base PC

    I'm quite new with Solaris. I got stuck in Solaris 8 installation just at almost the very beginning. After booting up the system from floppy and conituing pressing F2 and selecting booting from CD, I got an error message like:
    cannot mount on pci@0; 0/pci-ide@7; 1/ide01/sd@0; 0:a
    panic[cpu0]thread=FEC17440 vfs:mountroot
    then, the system reboots itself again and again every time it reaches this point. I guess it's a problem with my CD-ROM. But the problem persists even if I change CD-ROM or move CD-ROM from secondary master to primary slave, etc. I also tried to change harddisk, but did no good to the problem. Is there any experienced users who could provide me with some solutions?
    I'm using a system with: Pentium 133, 32 MB Ram, 4GB HDD, 3C905TX, ATI Rage II PCI, Matshita CR-587 CD-ROM, Serial mouse and so on. I also tried another system with: P III 450, Asus P3BF, 192MB Ram, Pioneer DVD-ROM, same HDD, and so on. The problem was still there with the latter system. However, I successfully installed Solaris 7 with the latter system before. Why can't it work with Solaris 8?
    Thanks a lot for the help.

    I've been having the exact same problems on a PowerEdge 500SC. I have managed to get Solaris up and running on the machine, however. I booted the DCA from the floppy disk and installed from the CD-ROM. When the DCA is ready to scan for devices I use the "Specific Scan" option to tell it to look for specific devices. I tell it to scan for all devices in the listing and in doing so the DCA finds ISA-based IDE controllers. After it provides a listing of the devices it found I use the "Device Tasks" option and the "View/Edit Devices" menu item then delete the Bus Mastering IDE controller device. Once the screen comes up to ask for a boot device, the drives will show up as on the ISA controllers.
    I have to go through this process every time I boot the machine but I am able to make the system run at least.
    I haven't figured out the ACPI problem, yet.
    Regards,
    Doug

  • Not able to add driver update during Solaris 10 installation on IBM x3550

    I am facing a problem with installation of Solaris 10 on IBM x3550.
    My question is not specific to IBM server.
    I am trying to add SAS driver during Solaris 10 installation. I selected option "Apply device driver update" (option # 4). It is asking to insert driver disk. But only showing floppy (f) and cdrom (c).
    IBM server 3550 doesnt have floppy drive and I have the driver image only in a USB stick. Unfortunately, Solaris 10 installation is not showing usb device during driver installation.
    Is there any way we can add usb device to the driver update disk list??
    Thanks in advance.

    Does no one have an idea?

  • Solaris 8 installation in Dell 8100 met "Resource Confilict"

    Hello There,
    During I installated Solaris 8 in Dell Dimension 8100, I received the warning message:
    "Resource Conflict: both devices are added.
    NON-ACPI device:PNP0c01
    Port 800-8DF, C00-C7F; Memory FFB00000-FFFFFFFF
    ACPI device:PNP0C01
    Memory: 9FC00-9FFFF, 3f87000-7F86FFF, FFFB0000-FFBFFFFF, FFC00000-FFFFFFFF."
    How can I recovery this "CONFLICT".
    Thanks very much !!!
    Jack

    AFAIK, this is a warning and can be ignored. But on dell
    systems there a lot of other problems that can prevent
    a successful solaris 8 installation (dell keyboard problems,
    problems with a panic when the system include a 3com
    3c905c NIC, ACPI problems, ...).
    See also:
    http://groups.yahoo.com/group/solarisonintel/message/26542
    Does it crash/reboot when you continue?
    Try to boot from the "Software 1 of 2" CDROM and at the
    "1 interactive or 2 custom jumpstart" prompt type "b kadb -v"
    instead of "1" or "2". In case it crashes while booting the
    solaris kernel from cdrom, this should give some usable
    error message...

  • Solaris 9/Installation in UltraSparc

    Hi,
    Im trying to install a Solaris 9 OS in a Sun Fire v240 machine.
    First I introduced a clear SCSI HDD and the Installation DVD in the DVD PCI device. Whe I did 'boot' in the OPROM prompt it seemed 'Bad magic nuber in disk label. Cant open disk label package. Evaluating: . Cant open boot device'. When I did 'boot cdrom' it answered 'Boot device: /pci@1e600000/ide@d/cdrom 0,0 f File and args: . Boot: cannot open kernel/sparcv9/unix Enter filename [kernel/sparcv9/unix]:'
    Then I formatted the HDD into a ufs format. And now when I do again 'boot cdrom' it answered me 'Boot device: /pci@1e600000/ide@d/cdrom 0,0 f File and args: . Boot: cannot open kernel/sparcv9/unix Enter filename [kernel/sparcv9/unix]:
    SCSI HDD and IDE DVD are correctly connected. Installation CD Solaris 9 is original.
    I even proved with a original Solaris 8 and Solaris 10 installation CD with the same results...
    How can I do a correct installation of Solaris??
    Thanks you!!

    Q1: Am I doing the right steps?Yes, assuming you made no error writing the iso images to blank CDs. Make sure to use the "write cd from
    iso image file" function in you cd writing software.
    You can also try to boot from the "Software 1 of 2" CD. It's bootable, too.
    Q2: Can I boot the Solaris 9 installation from the A drive, is there any way to create the boot floppy diskette(s) for it?Yes, the CD "Software 2 of 2" contains a 1.44MB boot floppy image, in file /Solaris_9/Tools/d1_image
    Write the image to a formatted floppy, using the msdos "rawrite.exe" or "dd.exe" utility.

  • Hardware Requirement for Solaris 8 Installation

    Hi,
    Can anyone give me the hardware requirements for Solaris 8 Installation. I need to install the following patches too..
    C++Runtime 108434-12
    Linker 109147-21
    J2SE Solaris8 (patch cluster)
    SUNWxwfnt (X Window System platform fonts)
    SUNWilof (ISO-8859-1 (Latin-1) fonts)
    Please help.
    Regards
    Aparna

    Check out http://docs.sun.com/app/docs/doc/806-1054 for the HCL for the intel version of Solaris 8.
    or http://docs.sun.com/app/docs/doc/806-2221-10 for Sparc hardware.

  • Sun Fire V490-Internal FC Drives missing in Solaris 10 installation program

    Hi,
    We have a V490 server that we are attempting to configure, but the internal FC drives are not available to the Solaris 10 installation program.
    The OpenBoot SCSI test fails:
    {3} ok test-scsi
    Testing /pci@9,600000/SUNW,qlc@2
    ERROR : ISP2200 RISC engine did not generate expected interrupt.
    DEVICE : /pci@9,600000/SUNW,qlc@2
    SUBTEST : selftest:loop-tests:inquiry-test:disk-test
    CALLERS : (f010f69c)
    MACHINE : Sun Fire V490
    SERIAL# : 66233440
    DATE : 03/27/2012 14:27:32 GMT
    CONTR0LS: diag-level=max test-args=
    /pci@9,600000/SUNW,qlc@2 selftest failed, return code = 1
    but the probe of the SCSI bus does not and displays the drives:
    {3} ok probe-scsi
    This command may hang the system if a Stop-A or halt command
    has been executed. Please type reset-all to reset the system
    before executing this command.
    Do you wish to continue? (y/n) y
    LiD HA LUN --- Port WWN --- ----- Disk description -----
    0 0 0 500000e010192d11 FUJITSU MAP3147FC 0110
    1 1 0 21000014c320ff73 SEAGATE ST314670FSUN146G055A
    How can we fix this problem?
    Thanks.
    S Kayal
    Edited by: 923748 on Mar 27, 2012 10:59 AM
    Edited by: 923748 on Mar 27, 2012 11:00 AM

    I don't think the test-scsi command is viable for that platform.
    The FC disks are "viewed" by the system as external to the SCSI controller, almost as if they were in a multi-pack.
    They are FC drives addressed by the chipset as SCSI disks.
    Try:
    <pre>probe-scsi-all</pre>
    Edit:
    Which release of Solaris 10 are you trying to install?
    Older releases that might be fine for V480's won't work on V490's.
    Edited by: rukbat on Mar 27, 2012 2:35 PM

  • Solaris 10 installation failure from cd's

    Hi All,
    I am attempting to install Solaris 10 on my x86 laptop. I run the installation from cd #1 and go through the steps and installation will begin. I am choosing to install the entire distribution and when cd #1 finishes (about 500 mb of the 4000mb) the machine is not prompting for the other cd's. The machine will simply reboot and give "Solaris 10 installation partially failed."
    Upon reboot the grub screen appears and it will load and then fail.
    Any ideas? Am I missing a step somewhere? Thanks.

    Hi All,
    I am attempting to install Solaris 10 on my x86 laptop. I run the installation from cd #1 and go through the steps and installation will begin. I am choosing to install the entire distribution and when cd #1 finishes (about 500 mb of the 4000mb) the machine is not prompting for the other cd's. The machine will simply reboot and give "Solaris 10 installation partially failed."
    Upon reboot the grub screen appears and it will load and then fail.
    Any ideas? Am I missing a step somewhere? Thanks.

  • Solaris 10 installation package

    Hi,
    I wonder if there is an installation version other than DVD or CD?
    I went to http://www.sun.com/download/sdl.jsp?5005588c-36f3-11d6-9cec-fc96f718e113=1
    and only see DVD or CD ISO version.
    I plan to connect an external hard drive to reinstall Solaris 10 to my sun fire X2100. So I guess I need a just software version of Solaris 10 installation.
    thanks,
    Feng

    Thanks the hints.
    I successfully unpack the sol-10-u4-ga-sparc-dvd-iso-a file to an external USB drive.
    I have a sun fire 2100 box, which is pre-insalled Solaris 10. Since its' OS can't go to root mode, Sun technician suggested me to over write the OS by a fresh Solaris 10 installation.
    I am using Hyper terminal software as a terminal console to connect to that Sun box.
    In Bios setting, the First Boot Device is "removable". Is it right?
    I am trying to use F2 when system is rebooted and that supposes to lead me to install Solaris 10 from my USB external drive.
    But my system always go back the preinstalled OS. What is the correct steps to install a new Solaris OS to over write the existing Solaris OS?
    thanks,
    Feng
    Attached is the screen when I try to boot install.
    GNU GRUB version 0.95 (608K lower / 1046400K upper memory)
    +-------------------------------------------------------------------------+
    | Solaris 10 1/06 s10x_u1wos_19a X86 |
    | Solaris failsafe |
    | |
    | |
    | |
    | |
    | |
    | |
    | |
    | |
    | |
    | |
    +-------------------------------------------------------------------------+
    Use the ^ and v keys to select which entry is highlighted.
    Press enter to boot the selected OS, 'e' to edit the
    commands before booting, or 'c' for a command-line.
    "

  • Solaris 10 Installation CDs

    Hi,
    I have downloaded solaris 10 installation CDs from site, verified them with checksums and burnt then into 700MB CDs. When I put the first one into CD-Rom and issue "boot cdrom" it prompt smthing like:
    there is no executable file ...
    What is the problem?

    ... In MS Windows ...
    I double-click an ISO file.
    It launches whatever program might be installed on my computer
    that is associated with burning-to-disk (Nero, Roxio, Isobuster, whatever).
    I pick a speed that I might want this time, such as 8x, and simply proceed.
    It just works.
    The program figures it all out for me.
    That's how I've burned ISO files from all sorts of sources for the last eight years.
    I double-click, and it just works.
    Are you sure you downloaded the images for CD's
    and not the five pieces of DVD that need to be joined before burning ?

  • Instant client for Solaris AMD x64

    Hi,
    I am desperately looking for OCI instant client for solaris AMD x64. I tried instant client download page (http://www.oracle.com/technology/software/tech/oci/instantclient/index.html) but it is not listed there. I have no idea who to contact within Oracle or Oracle tech support.
    Any help is greatly appreciated.
    Thank you,
    Boris

    I've just downloaded the basic and sqlplus zip files and sqlplus works fine. sqlplus is linked to libclntsh.so.10.1, so I doubt that file is corrupt.
    instantclient_10_2> ls -l
    total 225992
    -r--r--r--   1 oracle   dba      1594191 May 19  2006 classes12.jar
    -r--r--r--   1 oracle   dba         1525 May 19  2006 glogin.sql
    -rwxr-xr-x   1 oracle   dba      29618728 May 19  2006 libclntsh.so.10.1
    -rwxr-xr-x   1 oracle   dba      7860792 May 19  2006 libnnz10.so
    -rwxr-xr-x   1 oracle   dba      1404480 May 19  2006 libocci.so.10.1
    -rwxr-xr-x   1 oracle   dba      70141168 May 19  2006 libociei.so
    -rwxr-xr-x   1 oracle   dba       146640 May 19  2006 libocijdbc10.so
    -rwxr-xr-x   1 oracle   dba      1913800 May 19  2006 libsqlplus.so
    -rwxr-xr-x   1 oracle   dba      1437952 May 19  2006 libsqlplusic.so
    -r--r--r--   1 oracle   dba      1540457 May 19  2006 ojdbc14.jar
    -rw-rw-r--   1 oracle   dba         6690 Apr 28 14:43 sqlnet.log
    -rwxr-xr-x   1 oracle   dba        11536 May 19  2006 sqlplus
    instantclient_10_2> ldd sqlplus
            libsqlplus.so =>         /tmp/ic/instantclient_10_2/libsqlplus.so
            libclntsh.so.10.1 =>     /tmp/ic/instantclient_10_2/libclntsh.so.10.1
            libnnz10.so =>   /tmp/ic/instantclient_10_2/libnnz10.so
            libkstat.so.1 =>         /lib/64/libkstat.so.1
            libnsl.so.1 =>   /lib/64/libnsl.so.1
            libsocket.so.1 =>        /lib/64/libsocket.so.1
            libgen.so.1 =>   /lib/64/libgen.so.1
            libdl.so.1 =>    /lib/64/libdl.so.1
            libsched.so.1 =>         /usr/lib/64/libsched.so.1
            libc.so.1 =>     /lib/64/libc.so.1
            librt.so.1 =>    /lib/64/librt.so.1
            libaio.so.1 =>   /lib/64/libaio.so.1
            libm.so.2 =>     /lib/64/libm.so.2
            libthread.so.1 =>        /lib/64/libthread.so.1
            libmp.so.2 =>    /lib/64/libmp.so.2
            libmd.so.1 =>    /lib/64/libmd.so.1
            libscf.so.1 =>   /lib/64/libscf.so.1
            libdoor.so.1 =>  /lib/64/libdoor.so.1
            libuutil.so.1 =>         /lib/64/libuutil.so.1
    instantclient_10_2> ./sqlplus /nolog
    SQL*Plus: Release 10.2.0.2.0 - Production on Tue Apr 28 14:47:04 2009
    Copyright (c) 1982, 2005, Oracle.  All Rights Reserved.
    SQL> exit
    instantclient_10_2> uname -a
    SunOS xxxx 5.10 Generic_120012-14 i86pc i386 i86pc

  • Solaris 9 Installer Tarantella 3.42.947

    My company is still installing and using Tarantella 3.42.947 and we are migrating from Solaris 8 to Solaris 9. The installer for Solaris 8 will not work on Solaris 9. Is there someone who can send me or direct me to a place where I can get a copy of the Solaris 9 installer for this oldver version of Tarantella?
    Thanks,
    Scott

    We are unable to help with your question as this forum is only for Sun Update Connection issues.
    You may be able to find what you're looking for at http://www.tarantella.com/, but if not please try one of the other forums.

  • Solaris 10 Installation Problems

    I recently tried (several times) to install Solaris 10 on an x86_64 AMD machine with a SATA hard drive, but I kept running into problems. When using the boot DVD, it booted a temporary desktop, and asked me several questions. At the end it asked if I wanted to install from a CD/DVD or somewhere else. I clicked CD/DVD and clicked continue, and it said "Unable to read from disk, please ensure your disk drives are powered up" or something similar. From there, I am unable to eject the CDROM, and if I click Cancel it brings up the terminal - but I can't figure out how to reinitiate the installation from there.
    Any ideas why it keeps doing this? I really want to use Solaris but I can't even get it installed!
    Thanks.

    Another error message:
    Auto-layout was not successful because of disk space problems.
    to resolve this problem, you can reduce the number of file
    systems for auto-layout, or you can manually layout file systems.

  • Sol 9 x86 AMD installation

    Hey all. I'm in a rut career wise and decided to get certified w/Solaris. I ordered the x86 version, and I'm running into problems already.
    When using CD1 or the installation CD, I get the same following error:
    config error - missing controller?
    filesystem not mounted
    configuration assistant exited prematurely
    then it continues and asks me to choose which installation method i would like to use. when choosing the interactive, i get the following error message:
    could not load drivers for
    root filesystem could not be loaded
    the root filesystem error is something along those lines, i didn't write it down. after that, it just tells me to press a key, and my system reboots. My system config is as follows:
    AMD 1600 processor
    ECS K7S5A mobo
    512 PC2100 DDR RAM
    3 IDE drives - 2 40gigs, 1 60gig (60gig is blank, trying to install Solaris here, it's the primary master)
    Currently running a few operating systems (does that matter?)
    i cannot figure out what to do from here. i've checked the docs on Suns site, and i can't find a fix. i find lots of stuff about patches, etc...but i can't patch a cd now can i. i hope someone can help, i've been at it all day and starting to get a little frustrated. =] thanks for your time.

    This is probably the "pci function #5" problem for SIS chipsets.
    Apparently you can work around the problem by creating a custom
    DCA floppy diskette and installing/replacing a fixed ata.bef file on
    that floppy:
    http://groups.yahoo.com/group/solarisonintel/message/45595
    http://groups.yahoo.com/group/solarisonintel/message/45366

Maybe you are looking for