Solaris 10 can not boot; disks drive offline

hi, solaris 10 can not boot the operating system has 10 luns and this enabled the multipathing, he settled patches and reboot the computer does not start showing me the following errors:
WARNING: /pci@0/pci@0/pci@8/pci@0/pci@1/SUNW,qlc@0/fp@0,0/ssd@w203400a0b875837d,1f (ssd0): drive offline
WARNING: /pci@0/pci@0/pci@8/pci@0/pci@1/SUNW,qlc@0/fp@0,0/ssd@w203400a0b875837d,1e (ssd3): drive offline
WARNING: /pci@0/pci@0/pci@8/pci@0/pci@1/SUNW,qlc@0/fp@0,0/ssd@w203400a0b875837d,1d (ssd5): drive offline
into failsafe mode and slow 2 days in, I try to see the running operating system disk format and takes the response format and shows me the following errors:
# format
Searching for disks...WARNING: /pci@0/pci@0/pci@8/pci@0/pci@1/SUNW,qlc@0/fp@0,0/ssd@w203400a0b875837d,1f (ssd0): drive offline
WARNING: /pci@0/pci@0/pci@8/pci@0/pci@1/SUNW,qlc@0/fp@0,0/ssd@w203400a0b875837d,1e (ssd3): drive offline
WARNING: /pci@0/pci@0/pci@8/pci@0/pci@1/SUNW,qlc@0/fp@0,0/ssd@w203400a0b875837d,1d (ssd5): drive offline
hba ports have been connected
# luxadm -e port
/devices/pci@0/pci@0/pci@8/pci@0/pci@1/SUNW,qlc@0/fp@0,0:devctl    CONNECTED
/devices/pci@0/pci@0/pci@8/pci@0/pci@9/SUNW,qlc@0/fp@0,0:devctl    CONNECTED
# cfgadm -al
Ap_Id                          Type           Receptacle   Occupant     Condition
c2                                fc-fabric      connected    configured   unknown
c2::203400a0b875837d  disk            connected    configured   unknown
c3                                fc-fabric      connected    configured   unknown
c3::202400a0b875837d  disk            connected    configured   unknown
cfgadm -al command output c2 and c3 appears has been connected and configured, because luns in the format output informs me that disks have state drive offline?
any idea.

Hi--
Can you list the steps that lead this problem, please?
The drive offline message is a symptom of some kind of connection or underlying hardware problem.
If there were no system changes that lead to this problem, then I would look for connection or hardware issues.
Thanks, Cindy

Similar Messages

  • Can not Access disk drive attached to WRT350N via an FTP client

    Background
     I have a WRT350N v1 running the most current firmware. I have a static IP address for the WRT350N and I can ping it over the internet.  I have a disk drive attached to the 350N with a FAT32 partition that has been set up for shared access for a selected group and user. I have worked with cicso/linksys support to verify the linksys350N is set up correctly (?).
    Problem
    I can not access the disk drive attached to the WRT350N via an FTP client. I have tried the following FTP Clients: Transmit and Filezilla.  I get a "Connection established, waiting for welcome message...' message on the FTP client. Then it says Connect timeout, Can not connect to server. I CAN connect to other FTP sites so its not the FTP client software.
    What I have done so far
    1. deleted the old  and added a new FTP group and user
    2.  unplugged and reconnected my WRT350N and my cable modem
    3. Contacted Cisco/linksys support on-line and they verified my setup and can ping my 350N but thats as far as they are willing to help
    I haven' a clue as to what to do next. Any and all help is greatly appreciated. 

    Access your router set-up and make sure you have :
    1. Enabled FTP Server and Internet Access under the FTP Server subtab under Storage...
    2. Reduced the MTU size to 1300 under SetUp...
    3. Unchecked Filter Anonymous Internet Requests...
    If you have done all this and nothing works, then, you need to upgrade your router's firmware and re-configure your router and then enter the settings...
    Download Firmware 3.23 MB...
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...
    In the address bar type - 192.168.1.1...Leave the username blank & in password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    1. Enable FTP Server and Internet Access under the FTP Server subtab under Storage...
    2. Reduce the MTU size to 1300 under SetUp...3. Uncheck Filter Anonymous Internet Requests...See if this works for you...

  • Recovery media creator: "Can not get Disk driver information. No HDD Recovery area!...

    The Toshiba Recovery Media Creator can not be launched."
    That´s the final part of the message I receive when I try to make the system image.
    As you can see (image below), this recovery partition exists, I haven´t deleted nor modified it in any way, and besides it´s in good state. I don´t understand why I get this error message. What can I do to get this recovery partition recognized by the application. I really need to make a system image.
    Please, if somebody has any idea of how to fix this thing, I´d really appreciate your help.
    Thanks in advanced.
    Will
    Solved!
    Go to Solution.

    Will, I'm afraid you'll need to order recovery discs and restore the hard disk to its original out-of-the-box contents using them.
       Order Toshiba Recovery Media
    BTW, the 1.46 GB partition you're looking at is not the recovery partition. It contains the Windows Recovery Environment.
    -Jerry

  • Install can not find disk drive

    I'm trying to load Solaris 8 on a brand new Compaq Proliant 800 with 64Mb RAM and 2.1Gb SCSI Ultra Wide 3 hard drive. The system has all Compaq components and the server is listed in the Sun Hardware Compatibility List.
    I'm getting the no compatible hard drive found when the install is searching for a hard drive to write the OS. How do I go about fixing this problem? I purposely bought the Proliant 800 and avoided adding any additional drives/memory because I want to avoid compatibility issues. Do I need to download a driver to support the controler that came with the Compaq Proliant 800?
    Any hints will be greatly appreciated. Thanks,

    jkcwong, is that the message:
    <pre>
    SunOS Secondary Boot version 3.00
    prom_panic: Could not mount filesystem
    Entering boot debugger:
    [12ff05]:
    </pre>
    you get when you boot from the DCA floppy? According to some sun
    engineer that's a
    solaris bug (bug
    4344312), and the upcomming patches
    108822-02 / 110930-01 are expected to fix this problem.
    Since the problem is ACPI related, perhaps your bios has an option to
    disable ACPI support?

  • Hard drive issue, can not boot past disk utility

    I got off work this morning and was wanting to do a clean install of osx10.10, unfortunately I did something bad, with my lack of sleep. I think I canceled the operation when I clicked cancel during the reinstall of OS X. Now I can not boot past the disk utility screen. There is also no sub menu under my listed hard drive "Macintosh HD." Is there a way I can fix this?
    It's a brand new MBP, 15inch retina. I had it for only a week and I am at work right now. So if there is anything I can do from here that would be great!!
    I also tried to reinstall OS X from the disk utility and when it asked to select disk to install OS X my only option was the recovery HD

    Ok, I will try that. I still have my old MBP that I am supposed to be trading in. Good thing i haven't mailed it off yet.
    I just reset the SMC and Pram and tried to boot in recovery. Once it downloaded everything online and i went to install OS X, it asked me to select and disk where i want to install. Well, there wasnt a disk listed at all...
    So, now I will try to create a USB installer when i get home from work and try that out. I will keep you posted
    Thanks,
    Keith

  • I have a dvd stuck in the drive and as I can not boot is there a way of removing the dvd ?

    Hi
    I have a dvd stuck in the drive and as I can not boot is there a way of removing the dvd ?

    Boot with the option key down.  You will see a window showing all the bootable systems.  Select the OSX boot and hit return.  Once you are booted into OSX, use the Startup Disk system preferences to change your default boot volume.
    Startup Manager: How to select a startup volume

  • In the get info screen the HD drive is lock, can not boot the computer

    I can not boot my imac.  In the Get Info window the Hard Drive has no access marked for everyone and a  minus sign on the hard drive.  How can I get around this??

    Boot into Recovery (command-R at startup), launch Disk Utility, select the startup volume ("Macintosh HD," unless you gave it a different name), and run Repair Permissions (not Repair Disk.) Then reboot as usual. That will undo the worst of the damage. You may need to reinstall some of your third-party software.

  • Can not boot to external drive

    Hey there
    I have a MacBook2,1 running 10.7.4
    I am trying to create an external boot drive but I can not boot to an external drive.
    If I mount an install disk to any drive I have it will not boot to it. If I select it in startup drive or option boot it will not work.
    Please help. need this fixed ASAP

    Drive Preparation for Lion
    1.  Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button. Select Disk Utility from the main menu and click on the Continue button.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area.  If it does not say "Verified" then the drive is failing or has failed and will need replacing.  SMART info will not be reported  on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
    After formatting is complete quit DU and return to the main menu. Select Reinstall Lion and click on the Continue button. When the installer begins it will default to installing on the Macintosh HD volume. Click on the link below to Show All Disks. Locate your external drive and select it as the target.

  • Hello, can someone help me: my eMac G4 700 MHz. I can not boot it. If he starts appears on the screen, only a small "folder with a question mark." The Mac was not used 1 year. Question 1: Problem = hard drive? Question 2: Problem = PRAM battery? the What

    Hello, can someone help me: my eMac G4 700 MHz. I can not boot it. If he starts appears on the screen, only a small "folder with a question mark." The Mac was not used 1 year.
    Question 1: Problem = hard drive?
    Question 2: Problem = PRAM battery?
    the
    What can I do to boot?

    Restart with the Option key held down.
    If the internal drive shows up, it's the PRAM battery.
    If it doesn't, insert a compatible Mac OS 9 or X install disk, click the button with the circular arrow, and either repair the internal drive or install a new OS on it. If it doesn't show up in Disk First Aid(9) or the Disk Utility(X), it's either not plugged in or needs to be replaced.
    (97530)

  • Disk Utility - Restore can not unmount target drive

    Just got a brand new MacBook Pro with Lion. As usual there are "issues"..
    I wanted to move my old TimeMachine backup (250 GB) to a larger Firewire drive (500 GB) and found a lot of instructions on that.. Problem is they don't work on Lion. (Both are Iomega drives with Firewire)
    The instructions suggest that using Disk Utility to "restore" the new drive from the old will work but I always get the Error "Can not unmount target drive..." and I can see that the source drive is unmounted but not the target.  I did all of the "First Aid" stuff to both drives.. (and the target drive was turned into a MacOS partition and verified..)
    I then tried the exact same process on my old MacBook Pro (Leopard) and everything worked as expected..
    Was there another way to do this in Lion.. or is this broken..???
    Thanks for any feedback..
    John..

    Is the new drive prepped?
    Drive Preparation
    1. If you are preparing an external or a non-startup drive, then open Disk Utility in your Utilities folder.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area.  If it does not say "Verified" then the drive is failing or has failed and will need replacing.  SMART info will not be reported  on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
    In Disk Utility you clone as follows:
    Clone using Restore Option of Disk Utility
    Open Disk Utility from the Utilities folder.
    Select the destination volume from the left side list.
    Click on the Restore tab in the DU main window.
    Check the box labeled Erase destination.
    Select the destination volume from the left side list and drag it to the Destination entry field.
    Select the source volume from the left side list and drag it to the Source entry field.
    Double-check you got it right, then click on the Restore button.
    Destination means the new backup drive. Source means the old backup drive.
    If you still have a problem then boot into the Recovery HD:
    Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Choose Disk Utility from the main menu then click on the Continue button.

  • I have an iMac model 4,1 running OSX 10.6.8.   The CD/DVD drive went bad and I have replaced it.  However I can not get disks to eject.   I have asked about this before and tried all all the suggestions I have received but I can not eject.

    I have an iMac model 4,1 running OSX 10.6.8.   The CD/DVD drive went bad and I have replaced it.  However I can not get disks to eject.   I have asked about this before and tried all all the suggestions I have received but I can not eject.  
    Yesterday I opened up the iMac and reinstalled the drive to make sure that it was not an alignment problem.   I still can not eject.   When I try to eject the drive makes noises like it is ejecting but the disk does not come out.
    How do I solve this problem?

    Hi again Hal
    Link to your other thread > The slot loading CD/DVD drive in my...: Apple Support Communities
    You have also tried resetting the PRAM as I suggestion in your other thread...?
    See resetting the PRAM > About NVRAM and PRAM
    1. Shut down the computer.
    2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    3. Turn on the computer.
    4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    6. Release the keys.

  • I have lost my cd's and screen became gray i can not boot what should i do?

    Hi all
    i have lost my cd's and screen became gray i can not boot what should i do?
    i have tried to reset Vram
    tried to run safe boot
    but nothing happends
    i have a macbook pro core 2 duo 2GB ram 160 gb hard disk

    Use the computer your on now to download and burn a ISO of PartedMagic to a cd.
    In Windows 7 you can right click on the downloaded ISO and click burn to disk, other Windows versions use the free ImgBurn software.
    In OS X you can burn the ISO using Disk Utility.
    Hook up a external drive to the target Mac.
    Stick the PartedMagic disk into the Mac and reboot holding option and c keys (I forget which one works)
    Use the first option (default) to load PartedMagic into memory (watch out the disk will eject!)
    Once in PartedMagic there is a Mount Drive icon on the right, doubleclick it twice to open two windows (three total) you can now transfer your files after mounting the disks/partitions using the two open file windows.
    Unmount the drives before using the "Start" like menu in the lower left corner to quit PartedMagic.
    If your Mac works with all this then your in good shape, you just have a hosed operating system and a $29 Snow Leopard install disk (c boot off of it) and a Disk Utility Erase (with Zero Erase preferred) and a reinstall of OSX Snow leopard will do the trick.
    If your computer boots off the PartedMagic cd, but you can't find/access the internal drive, then your boot drive is dead and you need to replace it or have someone replace it for you.
    If your computer doesn't boot off the PartedMagic cd, then it's likely a serious hardware issue.

  • Imac 21" mid 2011 can not boot from USB device?

    Hi,
    hope someone can help me.
    Bought the new imac 21" and replaced the superdrive with a ssd drive.
    Works great but it seems that the imac is not able to boot from any usb device.
    I put my osx install disk in my external dvd drive and powered my mac.
    While booting up (pressing cmd) the mac does not recognize my external dvd drive. This works great with my MBP late 2008. But the imac can not boot from the dvd drive. Also pressing "c" while booting does not work. Doing that a grey screen appears and after some time mac boots from hdd.
    So i installed mac os via target mode over firewire withbmy old imac. This works.
    But now i want to install windows on a bootcamp partition.
    I can't boot from the windows 7 professional dvd, too. So i tried to create a bootable win 7 thumbdrive. Mac can't boot from this too. Reading many threads in some forum i tried with rEEfit. Reefit shows the usb thumbdrive whike booting, but using this will end in a black screen error from bios: "no bootable device....". Tried a knoppix on the usb thukbdrive, too.... No bootable device....
    It seems that there is no way to boot from ANY external usb device like dvd drives or thumbdrives......
    What more can i do? I tried for 2 evenings now, but nothing worked out for me......
    Currently i don't see any any to install win 7 without an internal superdrive, but can this be??
    Thanks for any comments.
    Kwicks

    Internal is definitely the easiest but you can boot from external HD or external optical drive, the mac is just very picky on what works and what doesn't.
    For an external drive or usb stick it has to be GUID partition table and have 10.4.5 or better installed on it, for more info check this link out ( http://support.apple.com/kb/ht1948 )
    Hope this helps,
    Joe

  • I can not boot my MacBook Pro. How do I get and save the data that is not backed up??

    I can not boot my MacBook Pro running on Lion 10.7.4. I pressed control, comment P and R keys and O got to the disk utility, then I tried to repair disk and it can not be repaired. I get a message that tells me to back up as much data as possible ?. But if I can not open the computer how can I save my data??
    I have a back up until 2 weeks ago on time machine. but the work of the last 2 weeks is extremely important how can I get it??
    If I use m time machine backup do I loose the additional data of the last two weeks!,
    Please help.. It's a huge amount of work that I have done and can not loose it

    If it were me, I'd get a new hard drive or SSD and put it in an external enclosure. Boot into the recovery partition, format the new drive (not the old one) and install the OS to it. Shut down the Mac, open it up, and swap the drives. You may be able to read your data from the old one externally if you're lucky. If you're very lucky you may be able to use Migration Assistant to move all your stuff to the new drive.
    Look at ifixit.com for the exact procedure to get to the drive on your model. If it's a unibody it's pretty simple.
    http://www.amazon.com/Sabrent-2-5-Inch-Aluminum-Enclosure-EC-TB4P/dp/B005EIGUD4/ ref=sr_1_3?ie=UTF8&qid=1392154588&sr=8-3&keywords=2.5+enclosure

  • Can not boot from OSX disc

    I recently partitioned my internal drive with an 80 gig partition to run Ubuntu , removed Ubuntu and now can not resize hd to recover the 80 gig that I used , there was a program with this Ubuntu install called rEFIt that was installed for the dual boot , My problem is that Itunes keeps crashing and I have spent somewhere around 8 hours trying to fix this issue and in the process I discovered that I now can not boot from the osx disc but I can boot from the Ubuntu disc , what can I do to correct this issue or is there anything that I can do to correct this and recover the 80 gig that I used ?

    The only solution was to erase hd and restore from time machine backup......
    According to everything that I have seen , read and tried when you partition the mac hd the way that mac is designed it will lock the hd thus preventing any access even using the startup disc to repair. As far as restoring everything after the erase and reinstall of the OSX that was easy and painless. FOR ANYONE WHO DOES NOT BACKUP THEIR DATA THIS IS WHY YOU SHOULD!!!!
    Once OSX is reinstalled the migration assistant will ask if you want to restore from a backup , if you have time machine or any other sort of backup simply choose the one you wish to restore from and continue , must admit I was a bit hesitant at first , I must say that everything restored with the exception of some settings that I have had to restore but they were not major settings  , after the backup is restored simply run update check and reinstall all updates , may need to do this a couple of times.
    Depending on the amount of data you have will determine the length of time for restore (500 gigs about 6 hrs.) but it will restore user account settings , connection settings  and network settings.
    Hope this will help if anyone has experienced the same problem.

Maybe you are looking for