Solaris 10 dual boot hangs on

I have a hp pavillion 6000 which I am trying to dual boot with solaris 10 x86. I partitioned my hard drive using systemresourcecd and formated with linux swap. when I try to boot off of my solaris 10 dvd, it hangs. It comes up wiht the copyright information, and doesnt change. help!

Hi
It is very easy to install Solaris with Windows XP dual boot if you have correct concepts of Operating System.Whch verison of Solaris are u trying to install. if you are installing Solaris 10 1/06 then there is a grub boot loader which comes with Soalris 10 .also u will first get the selection screen during first boot. if u r directly booting into windows then go to command prompt of windows adn type fdisk. then make the partition of solaris as active and then boot , now u will be able to boot with soalris/windows.
Best Regards
[email protected]

Similar Messages

New to Solaris - dual boot question

I have been using OpenSolaris on my ThinkPad T400s, dual booting with Windows 7. I want to give Solaris 10 a try. I've had it running in Virtual Box under OS X for a while, and I think I'm comfortable enough to try it out on my ThinkPad. Here is my question: will the Solaris Interactive installer let me install Solaris 10 in my existing OpenSolaris partition? And if it does, will it modify the bootloader so that I can still dual boot with Windows 7? I dont want to have to destroy partitions and re-install Windows. Once its on my hard drive, I can add myself as a user, install the Intel 5300 wireless driver, etc... Anyone have any other issues with Solaris 10 on a T400s?

Okay, well as usually happens, when I resort to help I end up solving my own problem.
In this case however, I still don't have a good grasp of what is going on.
I deleted the partition table with sgdisk --zap-all /dev/sda and then used gdisk to recreate it, specifically setting the code for /dev/sda1 to ef00.
I then reformatted the FAT partition, leaving the other one alone. After mounting /dev/sda1 to /boot and reinstalling linux and grub, I ran:
grub-install --target=x86_64-efi --efi-directory=$esp --bootloader-id=arch_grub --recheck
as described in the wiki, and
grub-mkconfig -o /boot/grub/grub.cfg
And it worked, including automatically detecting Windows on the other drive. Not sure what went wrong the first time but I'm glad to get it working.
Last edited by egan (2014-12-09 19:46:58)

Solaris 10 Boot Hangs on T1

Solaris 10 is hanging during boot from the OpenBoot firmware on my T1. Below is the output from doing an interactive boot from OpenBoot using the "boot -a" command. I use the default values for all options and the boot hangs after the root device is specified.
I'm rather new to Solaris so this problem has me stuck. Any ideas?
Thanks!
-JohnC
Sun Fire(TM) T1000, No Keyboard
Copyright 2005 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.20.0, 8184 MB memory available, Serial #<removed from post>.
Ethernet address <removed from post>, Host ID: <removed from post>.
Rebooting with command: boot -a
Boot device: /pci@7c0/pci@0/pci@8/scsi@2/disk@0,0 File and args: -a
Loading ufs-file-system package 1.4 04 Aug 1995 13:02:54.
FCode UFS Reader 1.12 00/07/17 15:48:16.
Loading: /platform/SUNW,Sun-Fire-T1000/ufsboot
Enter filename [kernel/sparcv9/unix]:
Enter default directory for modules [/platform/SUNW,Sun-Fire-T1000/kernel /platform/sun4v/kernel /kernel /usr/kernel]:
Name of system file [etc/system]:
SunOS Release 5.10 Version Generic_118833-24 64-bit
Copyright 1983-2006 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
root filesystem type [ufs]:
Enter physical name of root device
[/pci@7c0/pci@0/pci@8/scsi@2/disk@0,0:a]:

More information:
"boot -v" gives:
Rebooting with command: boot -v
Boot device: /pci@7c0/pci@0/pci@8/scsi@2/disk@0,0 File and args: -v
Loading ufs-file-system package 1.4 04 Aug 1995 13:02:54.
FCode UFS Reader 1.12 00/07/17 15:48:16.
Loading: /platform/SUNW,Sun-Fire-T1000/ufsboot
The boot filesystem is logging.
The ufs log is empty and will not be used.
Size: 0x79038+0x1cf01+0x31a0b Bytes
module /platform/SUNW,Sun-Fire-T1000/kernel/sparcv9/unix: text at [0x1000000, 0x1079037] data at 0x1800000
module misc/sparcv9/krtld: text at [0x1079038, 0x1091c7f] data at 0x184e910
module /platform/SUNW,Sun-Fire-T1000/kernel/sparcv9/genunix: text at [0x1091c80, 0x11e7d6f] data at 0x1854100
module /platform/SUNW,Sun-Fire-T1000/kernel/misc/sparcv9/platmod: text at [0x11e7d70, 0x11e7d77] data at 0x18a5d50
module /platform/SUNW,Sun-Fire-T1000/kernel/cpu/sparcv9/SUNW,UltraSPARC-T1: text at [0x11e7d80, 0x11eb05f] data at 0x18a6480
SunOS Release 5.10 Version Generic_118833-24 64-bit
Copyright 1983-2006 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Ethernet address = 0:14:4f:21:ac:68
mem = 8380416K (0x1ff800000)
avail mem = 8379793408
root nexus = Sun Fire(TM) T1000
pseudo0 at root
pseudo0 is /pseudo
scsi_vhci0 at root
scsi_vhci0 is /scsi_vhci
px1 at root: 0x7c0 0x0
px1 is /pci@7c0
PCI Express-device: pci@0, pxb_bcm0
pxb_bcm0 is /pci@7c0/pci@0
PCI-device: pci@8, pci_pci0
pci_pci0 is /pci@7c0/pci@0/pci@8
/pci@7c0/pci@0/pci@8/scsi@2 (mpt0):
        Rev. 2 LSI, Inc. 1064 found.
/pci@7c0/pci@0/pci@8/scsi@2 (mpt0):
        mpt0 supports power management.
/pci@7c0/pci@0/pci@8/scsi@2 (mpt0):
        mpt0 Firmware version v1.6.0.0 (IR)
/pci@7c0/pci@0/pci@8/scsi@2 (mpt0):
        mpt0: IOC Operational.
PCI-device: scsi@2, mpt0
mpt0 is /pci@7c0/pci@0/pci@8/scsi@2
sd1 at mpt0: target 0 lun 0
sd1 is /pci@7c0/pci@0/pci@8/scsi@2/sd@0,0
root on /pci@7c0/pci@0/pci@8/scsi@2/disk@0,0:a fstype ufs
pseudo-device: dld0
dld0 is /pseudo/dld@0
cpu0: UltraSPARC-T1 (cpuid 0 clock 1000 MHz)
cpu1: UltraSPARC-T1 (cpuid 1 clock 1000 MHz)
cpu2: UltraSPARC-T1 (cpuid 2 clock 1000 MHz)

Xp/solaris dual boot bug

Hello
I have a 80gb hard disk set up with win xp pro along
with a 25gb unformated partition. Recently I installed
solaris 10 x86 to the 25gb partition from sun's
website. the installation setup automatically selected
the 25 gb space. all seemed to be working fine. the
only problem was after installation solaris boot
manager selected solaris automatically if no selection
of win xp was made within 30 seconds. since i needed
xp pro as a default i used the utility OSBS (boot.exe
and osbs135). as instructed i have entered the saved
solaris.bin from mbr to xp root and have entered
corresponding entry in win.ini file. the new boot
manager enables xp selection by default, xp pro boots
all fine but if i select solaris nothing happens
except a blinking cursor.
It seems to me that solaris partition is all fine and
healthy as I added few packages from solaris
installation cd few days back. Only problem is i m
unable to boot from it with the OSBS boot manager.
Is this a known problem?? or is there any better boot
manager?
Any advice/suggestion will be highly appreciated.
Many thanks

Hi, I am not sure if this would work but it might. First of all do you know if you delete the solaris partition then wouldn't it go back to booting to Windows? Just wondering about that. Well anyways here is my proposed solution that enables booting Solaris from Windows XP boot menu. Actually wait do you have a floppy drive on your laptop or a portable one. Because this solution requires that. Reply if you have one.

How do I install dual-boot Solaris 8 and Solaris 9 on one hard disk ?

I tried to install Solaris 8 and Solaris 9 on same disk using CDs, but
the second installation overwrote the first Solaris which was installed
previoudly on the half-disk size partition of same disk.
How do I install two Solarises on one hard disk ?
Thanks
Yakov

There are no tricks to get Solaris to dual boot on the same drive. Just allocate and pick the free slices not used by the first Solaris install when you put in the second install. Technically speaking there is nothing preventing you from running seven separately bootable Solaris instances on the same drive (one of 8 available slices is overlap -- slice 2) provided you use a swap file on a root partition instead of reserving a whole slice for swap.

Dual boot windows 7 and solaris 11

Hi Friends,
Could some one please explain the steps to install dual boot windows 7 and solaris 11?
Thanks
Raja

Install Windows leaving a partition for Solaris. Install Solaris into the empty partition. Reboot. Use a partition manager if you need to shrink your current Windows Partition. GParted works great and is free.
alan

Dual Boot Windows 7 and solaris 10

Can some body guide me how to dual boot windows 7 and solaris 10?
Thanks

First partition your harddisk with at least 2 primary partitions, one for windows and the other for solaris if you only have one harddisk. It would be a good idea to create an additional small boot partition as the first partition as well if you intend on using an independent boot loader but it really depends on what your machine is capable of. For example, if you have multiple harddisk and your BIOS supports it, then you could just install each OS onto its own harddisk and use the BIOS function to disable/boot off specific harddisk. Otherwise, if you only have one harddisk and created multiple partitions, install windows7 first followed by solaris10, obviously installing into different partitions. If you have created a boot partition, then you can install the boot loader into that dedicated partition.

Dual boot Solaris 8 and Windows XP

Hello. I currently have windows xp as my OS. I would like to install Solaris 8 as a secondary OS. I have a separate hard drive I would like to put Solaris on. My question is, will the solaris installation allow me to choose which drive to install solaris to? Also, how can I set up my system to boot windows if I do nothing, but boot solaris if I choose to? Thanks for any help, I'm new to solaris and to dual-booting.

Try this URL:
http://sun.pmbc.com/faq/9.html
Hope it helps.
Senthilkumar
Developer Technical Support
Sun Microsystems, Inc.
http://www.sun.com/developers/support

Dual Booting Windows and Solaris

Hi
how do i dual boot windows and solaris
Do i install windows first and then solaris or do it the other way around..?
how do i make sure that Windows and Solaris appear in my boot options..?
Is their a guide on doing this...?
Thanks
Liam

Hey I did a quick google search for you. So I havent tried this method myself but it sounds reasonable.
The text below is from the following link:
http://www.hccfl.edu/pollock/AUnix1/DualBoot.htm
"Solaris boot loader
Partition the drive to leave at least 2GB of space available for Solaris;
more drive space is desirable.
As with Linux, install Windows first then Solaris.
Do not use the Installation CD but boot and install
from Software CD 1.
If you accept the default partitioning scheme which
the installer provides you will soon run out of space in
your / and /usr partitions since only enough space is
allocated to install the system.
All extra space is allocated to /export/home.
A typical installation on a 4.5GB partition might look
something like this:
Filesystem Size Used Avail Use% Mounted on
/dev/dsk/c0d0s0 900M 536M 310M 64% /
/dev/dsk/c0d0s1 334M 109M 192M 36% /var
swap 671M 8.0k 671M 1% /var/run
swap 671M 8.0k 671M 1% /tmp
/dev/dsk/c0d0s5 845M 222M 565M 29% /opt
# (FAT32 partition):
/dev/dsk/c0d0p0:1 5.0G 3.3G 1.6G 66% /c
/dev/dsk/c0d0s7 1.1G 92M 954M 9% /export/home
/dev/dsk/c0d0s4 752M 225M 474M 33% /usr/local
The Solaris boot selector enables you to choose either
Solaris or Windows with Solaris as the default.
(I prefer grub or lilo!)
To mount FAT under Solaris:
# mount -F pcfs /dev/dsk/c0d0p0:c /dos (or �:1�?)
And the vfstab file:
/dev/dsk/c0d0p0:c - /dos pcfs - yes -
To create a GRUB boot floppy, follow these steps:
$ mkfs -t ext2 /dev/fd0
$ mount /dev/fd0 /mnt/fd0
$ mkdir /mnt/fd0/boot /mnt/fd0/boot/grub
$ cp /boot/grub/stage[12] /boot/grub/grub.conf \
> /mnt/fd0/boot/grub
$ /sbin/grub --batch <
Hope this helps!
/Oscar

Solaris 11.1 boot hangs after motherboard firmware update

I flashed my Supermicro X9SAE motherboard to v2.0a (form v1.0), now my system hangs displaying "SunOS Release 5.11 Version 11.1 64-bit Screen. Copyright,,,,,"
The grub menu appears ok before this, from which I have tried playing around with kmds debug modes and kernel debug (which hangs)(https://blogs.oracle.com/dmick/entry/diagnosing_kernel_hangs_panics_with).
I have attempted booting form the live media, but this hangs in the same place. Supermicro support sent me firmware v2.00 (build date 07/31/2012) earlier today, I re-flashed but same problem. I am hoping they can provide me with v1.0. Could this be the problem - incompatible bios? Most appreciative of any assistance that can be provided.
My system specs;
Supermicro X9SAE Motherboard
Intel Xeon E3-1275v2 Processor
4 x 8GB DDR3-1333 ECC x8 SERVER SDRAM Module (HYNIX ORIGINAL)
1 x IBM ServeRAID M1015 SAS RAID Controller
8 x SATA Hitachi drives 7k4000 3TB
850W Corsair unit
My Card
Adapter SAS9211-8i
PCI Slot 10
PCI Address 01:00
MPT Firmware Revision 14.00.00.00-IT
SAS Address 500605B0:04EF1210
NVDATA Version 0E.03.00.04

Glad to hear!
I am unsure if this is a supermicro bios issue or on Oracle's side.. I'll probably end up opening a ticket in both locations. I love the super-micro boards so and their barebone systems are used for most of my system builds. However I did not notice this behavior with the AMD boards I used in VM Hosts even though they are also supermicro. So maybe its a Solaris VT-D implementation issue.
Are you seeing a message from Solaris at boot that says "Bios miss-represents the presence of IOMMU"? I get that on some of the systems that exhibit this issue, yet there there is no doubt that they DO have IOMMU capabilities.

Solaris 10 06/06 x86 HP DL585 boot hang aftrer reboot HELP!!!

Solaris 10 06/06 x86 HP DL585 boot hang aftrer reboot
when I shutdown server and power on,
solaris usually start.
but after "reboot" (or "init 6"), boot hang on
"SunOS Release 5.10 Version....
Copyright ...
Use is subject to license terms"
HELP!!!

try getting the Solaris x86 drivers frm HP....
http://search.hp.com/redirect.html?type=REG&qt=Solaris+x86&url=http%3A//h18007.www1.hp.com/support/files/server/us/download/22412.html%3Fjumpid%3Dreg_R1002_USEN&pos=1
hope it helps.

Solaris 10 & Windows 2K dual boot

Hello forum,
I installed Solaris 10 on a machine such that it dual boots with Win2K . All seemed well , I logged into Solaris and Win 2K and it worked properly .
I tried logging into JDS 3 and after that it does not boot into WIn 2K .
I get the menu asking which OS to boot into and whe I give the ID for Win 2K , it just returns to the menu .
Any help in solving this issue is highly appreciated .
Thanks and Regards

Thanks for the reply , but do you have any idea as to what might have screwed it the partition.
Also I don't think there is an issue with the partition , I strongly suspect the boot files would have changed though I really doubt it .
Any ideas ???
Thanks in advance .

Dual boot of Solaris 10

Hi,
I am new to Unix world , Can I install Solaris 10 with Dual boot support. I have to keep Windows XP as well as Solaris.
And my second question is that Solaris 10 is the Desktop OS or Server OS ? And what is the difference between SunOS 5.2 and Solaris 10.
Amir Hussain
Thanx in Advance.

Yes, I have Solaris 10 x86 (03/05) running along with
Windows XP on a Dell Optiplex GX280. I loaded XP
first, created a partition for the Solaris install
and then loaded Solaris. The Solaris boot loader
comes up at power up so that you can select Solaris
or XP. I am using Solaris 10 on both servers and
destops. I am not experienced enough to tell you the
difference between SunOS 5.2 and Solaris 10. Sorry.Thanks Daniel,
Its mean First of all I have to install xp, then create a partition for solaris 10. Then install solaris 10.
I have IBM compatible PC.
I

Dual Boot Solaris 2.5.1 and 2.8

Is it possible to dual boot a Sparc Ultra 10 workstation with Solaris 2.5.1 and a more recent version (such as 2.8). If so please point me to some documentation.
This is required as we are running several pieces of software licensed against the hostid, that will soon require different versions of Solaris.
Thanks in anticipation.

You should make an alias for your second OS location, for example disksol28.The easiest way to do this is run the format command. Write down the physical path for each disk you see. Your boot disk is probably c0t0d0 and the second disk, if you have one would be c0t1d0. If you are going to install 2.8 on another slice/partition of the first disk, write down that pathname, you'll need it for the nvalias command. If you are going to install it on the second disk then the alias "disk1" will probably work already, if you did not change the eeprom during install. You'll just have to:
ok
boot disk1
If you install 2.8 on another slice of your single disk then do not forget to include the slice in your alias.
If I asume your 2.5.1 is a flat file system (/ only, no /usr, /var, /opt, /export etc.) on slice 0 and swap is on Slice 1, then I can put another flat file system on Slice 3 - don't touch Slice 2. This OS can use the same swap Slice 1. To create an alias to boot from Slice 3:
ok
nvalias disksol28 <pathname from format goes here> :d
reset <- (locks it in to NVRAM)
example:
nvalias disksol28 /pci@1f,400/pci@1/disk@0,0:d
reset
Note:Slice 0 is asumed in most aliases. For example if your alias ends wih disk@0,0 Slice 0 is assumed. You can also say disk@0,0:a to indicate Slice 0 but ":a" is not really needed.
If you are booting off of any other slice then it must be indicated in your alias.
Slice
0 :a
1 :b
2 :c
3 :d
4 :e
5 :f
6 :g
7 :h
If you want to create an alias for your second disk (c0t1d0) with root on slice 0:
ok
nvalias disksol28 <pathname from format goes here>
reset <- (locks it in to NVRAM)
example:
nvalias disksol28 /pci@1f,400/pci@1/disk@1,0
reset
Please write down any custom aliases because a Stop+n or set-defaults will wipe them out.
If you make a mistake with nvalias then:
ok
nvunalias disksol28
reset
If you want disksol28 to be your primary boot device then:
ok
setenv boot-device disksol28
setenv diag-device disksol28
reset
Good Luck,
John

WinXP dual boot Solaris on 2nd hard drive problem...

Hi there ppl,
run into a bit of a prob with dual booting winxp and solaris. I have WinXP on 1st hard drive and Solaris on 2nd hard drive 2 (Solaris - partition 1 with slice 0 x86 active, DOS - partition 2 for installing linux later, DOS - partition 3 for fat32 file storage later).
I want to boot to Solaris on drive 2 from the WinXP boot loader on drive 1. Could somebody please tell me exactly how to do this as I've copied the bootsect.sun file from Solaris via floppy to the WinXP C:\ drive, and edited the WinXP boot loader to:
[boot loader]
timeout=30
default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /noexecute=optin /fastdetect
multi(0)disk(0)rdisk(1)partition(1)C:\bootsect.sun="Solaris/x86"
and when I select to boot to Solaris I get:
Windows could not start because the following is missing or corrupt:
<Windows root>\system32\hal.dll
Please reinstall a copy of the above file
WinXP still boots ok.
Any help would be much appreciated, thanks already.

I am having a same issue....
1.....1st 80 GB hard disk, I had window XP installed. (NTFS format)
2....add 200 GB, 2nd hard drive, make 3 partitions, on first 50GB partition I have install Solaris 10.....Having some issue with network config, but its resolve, thank this forum.....
Now, everytime when ever I need to go to Solarid, I have to go in BIOS screen and switch HD, I mean if I want to boot to solaris, I have to make a 2nd (200GB) hd primary..Soaris work fine, but from the GRUB menu, if I select window, its get hung up...
now if I want to boot to window, again I have to go to BIOS and need to switch around hdd.... make 1st (80GB) hdd primary, windows work fine....
Questions are, I do not want to go bacK & forth in BIOS.....
1....Can some one help me, provide me the step-by-step information that how can i set up dual boot, so I can use my 2nd drive (200GB) as a primary and from the GRUB, I select windows and its boot to windows... if its otherway around,,,its still ok....I don't want my kids mess up BIOS....
2...What is a chainloader+1...can some one explain?...what is +1 mean.
3....How to install GRUB in MBR?
Lion-O any ideas, how to boot windows bootloader from 2nd HD? Please step-by-step Instuctions....

Solaris 10 dual boot hangs on

Similar Messages

Maybe you are looking for