Solaris 10 install on an HP dl320 - unable to

Attempting to install Solaris 10 u3 x86 on an HP DL320s.
Hp has provided Solaris 10 drivers for the P400 array controller.
I can boot from HP's iLo virtual cdrom but when I attempt to "Apply driver updates" for the array controller (from the same cdrom drive I booted from) the installation it returns:
"CD/DVD not found" .
Tried the virtual floppy: "floppy failed to mount"
Tried a USB floppy with the same results.
PXE booted the machine and tried the virtual and USB drives. Still no love.
Any insight or suggestions would be greatly appreciated.

First of all I don't think this is a Solaris supported server by HP.
Second, you can't use a USB floppy drive to install the drivers. And mounting a floppy (virtual floppy) is again treated as USB.
If the system has a floppy drive, it should work.
else Please try to download the latest CPQary 3 drivers from HP.com, whihc includes a iso image burn the same and you can use it at the time of installation.

Similar Messages

Solaris 3i install - did work, now broken - unable to contact OAD

I did have an install on Solaris (single machine) of Discoverer 3i working, but it has stopped working. in the locator.log I find:
Tue Feb 13 11:14:41 CST 2001 Number of server machine = 1
Tue Feb 13 11:14:41 CST 2001 Locator: Server machine 0 = usicesn2
Tue Feb 13 11:14:41 CST 2001 Locator: IP addresses changed. Flushing cache
Tue Feb 13 11:14:41 CST 2001 Locator: IP addresses changed. Initializing OAD list
Tue Feb 13 11:14:41 CST 2001 Locator: Creating new OAD connections
Tue Feb 13 11:14:41 CST 2001 Unable to contact OAD on usicesn2
Tue Feb 13 11:14:41 CST 2001 Locator: IOR = IOR:000000000000001349444c3a4443494c6f6361746f723a312e30000000000001000000000000006200010000
0000000d3137322e32302e31352e32310000e72e0000004600504d43000000000000001349444c3a4443494c6f6361746f723a312e30000000000022444953434445564f726
1636c65446973636f76657265724c6f6361746f72332e3300
Tue Feb 13 15:47:50 CST 2001 Session manager started at 13-Feb-01 3:47:50 PM 743ms
Tue Feb 13 15:47:50 CST 2001 Prefs object GetData took: <Hour:Min:Sec.Ms> 0:0:0.20
Tue Feb 13 15:47:50 CST 2001 Request for Session name = DATESTOracleDiscovererSession3.3
Tue Feb 13 15:47:50 CST 2001 Locator: Request for for Session Manager number = 1
Tue Feb 13 15:47:50 CST 2001 Locator: Creating new cache for DATESTOracleDiscovererSession3.3
Two obvious problems. 1) Can't contact OAD on usicesn2 (the machine that has the entire 3i suite), and the attempt to access DATEST. DATEST was the NT machine we previously were using before migrating to Solaris. How does it know about DATEST?
I've tried stopping, starting, deregistering, re-registering, putting in the hard ip address, and no joy.
null

How did you have discoverer 3i working on one machine (solaris). I was under the impression that in 3i Solaris can only be used as a HTTP server and for the discoverer server you need to use an NT machine.
I am using the above setup but when I start the start_locator it says it cannot bind to the preference session. I then started the locator on the NT machine and moved the locator.ior file on the solaris box. It seemed to work then. Also using everything on one NT box seems to work.
Can you please give me an idea as how use are using solaris for your locator, preference and session component.

After installing Windows 8, I am unable to download the creative cloud and the program I purchased for school.

After installing Windows 8, I am unable to download the creative cloud and the program I purchased for school.

I purchased photoshop for my computer. I updated my computer's operating system. I logged into adobe. I am unable to download the program again unless I pay again or use the trial.

Photoshop CS6 is not installing properly and i am unable to locate the application

HELP ME!!!! My trial Photoshop CS6 is not installing properly and i am unable to locate and open the application on my mac. I am just going around in circles from file to file and back to the starting "intall" icon

I am on the Adobe Download Assistant. It was stuck at "less than a minute" for an hour and a half, showing that the installation was basically done, since the installation bar was full. But it was stuck. Now it has stopped all together, and is restarting the download from scratch.
Apparently it does not save the download, or only saves a small portion.
c:\adobe/CS6MasterCollection/MasterCollection_CS6_LS16.7z.adadownload
It is at 85.6 MB, even though a short time ago it was close to 99.9% done with the 6,352 MB download.
My internet connection is fine, all is working, and I am able to browse, etc.
I have been careful to keep activity minimal on the computer, so as to avoid conflicts.
The conflicts are with the Adobe Download Assistant.
I amabout ready to just give up, and look for alternatives.
Please help.

I have Adobe reader installed. However, I am unable to open some files because it is asking for Adobe's approval to open the files. How do I do this please?

I have Adobe reader installed. However, I am unable to open some files because it is asking for Adobe's approval to open the files. How do I do this please?

That message is NOT from Adobe, and has nothing to do with Adobe's approval for anything.
Quite the opposite: Adobe Reader is NOT YET RUNNING, Adobe aren't involved. Some other app or program is putting out that message. Have you tried giving that permission?

Problems making Solaris 10 install disk for x86

I have an Ultra 40 M2. I made a boot/install DVD disk with Solaris 10 for x86.
The system just doesn't recognize it at all, like there is nothing in the DVD drive.
What am I doing wrong?
The DVD drive does recognize other DVDs, just not the Solaris 10 install one (I created two install disks to no avail)

How are you burning the DVD. What software/options.
Theres a howto here
http://www.sun.com/software/solaris/self_help.jsp#burning

Solaris 10 instalation in Guest Domain - Timed out waiting for TFTP reply

I have the next trouble
I have a Sun Fire T1000 and i want install two Guest LDOM's with Solaris10 in each one, I Install the LDOM Manager 1.0.3 and the service is "online" also the another services needed
First Setup the 2 Guest LDOM's in the primary Domain sucesfully .... here is a desc of the configuration.
# ldm list-bindings
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
primary active -n-cv SP 4 1G 0.1% 2h 14m
MAC
00:14:4f:a7:85:1e
VCPU
VID PID UTIL STRAND
0 0 0.2% 100%
1 1 0.2% 100%
2 2 0.1% 100%
3 3 0.1% 100%
MAU
ID CPUSET
0 (0, 1, 2, 3)
MEMORY
RA PA SIZE
0x8000000 0x8000000 1G
VARIABLES
diag-switch?=true
security-#badlogins=0
IO
DEVICE PSEUDONYM OPTIONS
pci@780 bus_a
pci@7c0 bus_b
VCC
NAME PORT-RANGE
primary-vcc0 5000-5100
CLIENT PORT
aplica_srss1@primary-vcc0 5001
aplica_prod@primary-vcc0 5000
VSW
NAME MAC NET-DEV DEVICE MODE
primary-vsw0 00:14:4f:a7:85:1e bge0 switch@0
PEER MAC
vnet2@aplica_srss1 00:14:4f:fb:f4:e0
vnet1@aplica_prod 00:14:4f:fb:2c:60
VDS
NAME VOLUME OPTIONS DEVICE
primary-vds0 vol1 /dev/dsk/c0t0d0s3
CLIENT VOLUME
vdisk1@aplica_prod vol1
VCONS
NAME SERVICE PORT
SP
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
aplica_prod active -t--- 5000 4 2G 15% 9m
MAC
00:14:4f:fb:2c:60
VCPU
VID PID UTIL STRAND
0 4 35% 100%
1 5 0.0% 100%
2 6 7.0% 100%
3 7 84% 100%
MEMORY
RA PA SIZE
0x8000000 0x48000000 2G
VARIABLES
auto-boot?=true
boot-device=
use-nvramrc?=true
NETWORK
NAME SERVICE DEVICE MAC
vnet1 primary-vsw0@primary network@0 00:14:4f:fb:2c:60
PEER MAC
primary-vsw0@primary 00:14:4f:a7:85:1e
vnet2@aplica_srss1 00:14:4f:fb:f4:e0
DISK
NAME VOLUME TOUT DEVICE SERVER
vdisk1 vol1@primary-vds0 disk@0 primary
VCONS
NAME SERVICE PORT
aplica_prod primary-vcc0@primary 5000
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
aplica_srss1 bound ----- 5001 24 13184M
MAC
00:14:4f:fb:ad:fb
VCPU
VID PID UTIL STRAND
0 8 100%
1 9 100%
2 10 100%
3 11 100%
4 12 100%
5 13 100%
6 14 100%
7 15 100%
8 16 100%
9 17 100%
10 18 100%
11 19 100%
12 20 100%
13 21 100%
14 22 100%
15 23 100%
16 24 100%
17 25 100%
18 26 100%
19 27 100%
20 28 100%
21 29 100%
22 30 100%
23 31 100%
MEMORY
RA PA SIZE
0x8000000 0xc8000000 13184M
VARIABLES
auto-boot?=true
boot-device=
NETWORK
NAME SERVICE DEVICE MAC
vnet2 primary-vsw0@primary network@0 00:14:4f:fb:f4:e0
PEER MAC
primary-vsw0@primary 00:14:4f:a7:85:1e
vnet1@aplica_prod 00:14:4f:fb:2c:60
VCONS
NAME SERVICE PORT
aplica_srss1 primary-vcc0@primary 5001
Then i mount the ISO images of The solaris OS 5/08, Later install the jumpstart server without troubles.... Here are the Configuration files needed for the properly setup of the service for a better guide

# ./add_install_client -d -e 0:14:4f:fb:2c:60 -s Zolder:/var/jump_start/ sun4v
cleaning up preexisting install client "0:14:4f:fb:2c:60"
To disable 0:14:4f:fb:2c:60 in the DHCP server,
remove the entry with Client ID 0100144FFB2C60
To enable 0100144FFB2C60 in the DHCP server, ensure that
the following Sun vendor-specific options are defined
(SinstNM, SinstIP4, SinstPTH, SrootNM, SrootIP4,
SrootPTH, and optionally SbootURI, SjumpCF and SsysidCF),
and add a macro to the server named 0100144FFB2C60,
containing the following option values:
Install server (SinstNM) : Zolder
Install server IP (SinstIP4) : 172.24.0.10
Install server path (SinstPTH) : /var/jump_start/
Root server name (SrootNM) : Zolder
Root server IP (SrootIP4) : 172.24.0.10
Root server path (SrootPTH) : /mnt/s0/Solaris_10/Tools/Boot
Boot file (BootFile) : 0100144FFB2C60
# cat /etc/inet/hosts // The Content of this file is exactly with ipnodes file
127.0.0.1 localhost
172.24.0.10 Zolder loghost
172.24.0.9 primary-vsw0
172.24.0.8 aplica_prod
172.24.0.7 aplica_srss1
# cat /etc/ethers
00:14:4f:fb:2c:60 aplica_prod
# cat /etc/bootparams
aplica_prod root=Zolder:/mnt/s0/Solaris_10/Tools/Boot install=Zolder:/var/jump_start/ boottype=:in rootopts=:rsize=8192
# cat /etc/dfs/dfstab
share -F nfs -o ro,anon=0 /var/jump_start/
share -F nfs -o ro,anon=0 /mnt/s0/Solaris_10/Tools/Boot
share -F nfs -o ro,anon=0 /mnt/s1
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
vsw0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.24.0.10 netmask fffffe00 broadcast 172.24.1.255
ether 0:14:4f:a7:85:1e
vsw0:1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.24.0.9 netmask fffffe00 broadcast 172.24.1.255
Here i plumb up the networks interfaces and setup the vsw0 device and change the MAC address of the vsw0 for the same of the bge0 device.
Then i Log to a Guest LDOM aplica_prod
----------START CONSOLE 1-------------------------------
# telnet localhost 5000
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
Connecting to console "aplica_prod" in group "aplica_prod" ....
Press ~? for control options ..
----END CONSOLE 1----
At the same time i open another console for startup the Guest LDOM aplica_prod i make a snoop of the vsw0 interface
---START CONSOLE 2---
# ldm start aplica_prod
LDom aplica_prod started
-bash-3.00# snoop -d vsw0 | grep aplica_prod
Using device /dev/vsw0 (promiscuous mode)
---END CONSOLE 2-----
In the other console is produced the next exit
----START CONSOLE 1------
Sun Fire(TM) T1000, No Keyboard
Copyright 2008 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.28.9, 2048 MB memory available, Serial #66792544.
Ethernet address 0:14:4f:fb:2c:60, Host ID: 83fb2c60.
Boot device: File and args:
ERROR: boot-read fail
Evaluating:
Can't locate boot device
{0} ok boot vnet1 install
Boot device: /virtual-devices@100/channel-devices@200/network@0 File and args: install
Requesting Internet Address for 0:14:4f:fa:82:17
Requesting Internet Address for 0:14:4f:fa:82:17
Timed out waiting for TFTP reply
---END CONSOLE 1-----
in the console 2 the snoop generates an exit of the net traffic for the vsw0 device
----START CONSOLE 2--------
primary-vsw0 -> aplica_prod RARP R 0:14:4f:fb:2c:60 is 172.24.0.8, aplica_prod
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
primary-vsw0 -> aplica_prod RARP R 0:14:4f:fb:2c:60 is 172.24.0.8, aplica_prod
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
----END CONSOLE 2----
Once start the snoop to produce messages make a ping to the IP's that should be assigned in the host file and all give a succesful answer BUT without start the Solaris 10 Instalation
# ping 172.24.0.8
172.24.0.8 is alive
# ping 172.24.0.9
172.24.0.9 is alive
# ping 172.24.0.10
172.24.0.10 is alive
I really need help with this trouble ..and any help or advice will be thrully appreciated
Thanks
PD: any other required configuration file will be provided if is needed

Moving disks while maintaining Solaris 10 install from one v240 to another.

Hi,
I want to move a Solaris 10 install from a sunfire v240
with a single cpu to another sunfire v240 with dual cpu's. Here are the
details of the hosts as well as configuration.
I have 2 sunfire v240's. One has a single 1 Ghz cpu and the second has
dual 1.5 Ghz cpu. I want to move the disks of the single cpu host to
the host with dual cpu's. I want to keep the installed version of
Solaris 10 intact. The installation of Solaris is split across 2
mirrored disks, i.e. 4 disks in total. I am using Suns volume manager
for mirroring and also have one files system mirrored with zfs.
The questions I have are the following:
1) Can I simply shut down the servers and swap the disks to the
destination host, in the same disk slots? The controllers the disks are
on line up and are the same between the 2 hosts.
2) Will the kernel pickup the changes moving from a single 1 Ghz cpu to
dual 1.5. Ghz cpu's with out any problems? Will the kernel pickup the
faster cpu's speeds. i.e. will it know it is now running dual 1.5. Ghz
cpu opposed to a single 1 Ghz?
3) Would we have to break the mirroring on the OS before shutting it
down?
4) As another option, instead of swapping disks, could we swap the
cpus? Move the dual 1.5. Ghz cpu's to the other host? Will the
motherboards read the updates of the cpu or are their jumper settings we
would need to update?
Thanks for your help.

Box A
Sparc Solaris 9, Oracle 10g
Box B
Solaris 10 x86, Oracle 11g
I know there are many factors, but I'm pretty new to both unix & oracle, so I >needed some general steps to get me started. You have many options.
Since you're in 10g, Have the Target Database created in Solaris 10 x86, Oracle 11g.
you can use,
RMAN - Cross platform Transportable Tablespaces.
Datapump Export and Datapump import.
Read the following:
How To Use RMAN CONVERT DATABASE for Cross Platform Migration - 413586.1
http://download-uk.oracle.com/docs/cd/B19306_01/backup.102/b14191/dbxptrn.htm
http://www.oracle-base.com/articles/10g/OracleDataPump10g.php
http://www.oracle-base.com/articles/10g/RMANEnhancements10g.php#cross_platform_tablespace_conversion

Solaris 10 Install Hangs at 15% on my HP DL 585?

Solaris 10 Install Hangs at 15% on my HP DL 585
I have taken out all the additional extra cards so I am left with the basic box, it has been configured to run in Raid 1 so my four disks become two.
I can still get it to bring up a shell and do other things, but the installer just appears not to want to go pass 15%
Help?

Which version of Solaris and how much memory do you have in the system.

Minimize and maximize Solaris 10 installed on VM virtual Box.

How can I minimize and maximize Solaris 10 installed on VM virtual Box.
Thanks
Paulo

Solaris is working just fine. Everything is ok. now since I open Solaris via VM Virtual box, the Solaris main page fills only half of the monitor. I can minimize/maximize the Virtual Box. But Solaris dimensions are fix and doesn't change. This leaves me a little room to open applications on Solaris. I had the same problems with my Ubuntu, by installing adds-on it was fixed. For Solaris I installed Guest additions, didnt help.
Thanks
Paulo

I have installed flash player but am unable to run it. Can you help me?

I have installed flash player but am unable to run it. What should I do?

You have not mention information about your operating system but still;
Windows:http://helpx.adobe.com/flash-player/kb/uninstall-flash-player-windows.html
Macintosh:http://helpx.adobe.com/flash-player/kb/uninstall-flash-player-mac-os.html
If issue still persist;provide information Regarding operating system you are using and product version.
Sarika

Adding packages from solaris 8 install disks

I need Solaris Make for Solaris 8. I have installed Solaris 8 off of downloaded Solaris 8 install disks. I apparently forgot to include Solaris Make in the install and now need to add it. When I copy the pkg SUNWxcu4t (the pkg for make and scc) and pkgadd it it claims installation is sucessful but still I have no make. It is supposed to install to /usr but there is no make there.
What am I doing wrong?
Thanks

Ok I have all of my compilling isuse resolved!
Just in case anyone else browsing this forum has the same problems here is what I have learned:
These are the relevent Packages:
for tools (ar, sccs, lex, yacc, make, nm, truss, ld, as)
SUNWbtool, SUNWsprot, SUNWtoo
for libraries & headers:
SUNWhea, SUNWarc, SUNWlibm, SUNWlibms
SUNWdfbh, SUNWcg6h
for ucb compat:
SUNWsra, SUNWsrh
You definatly need to use Solaris make (found in SUNWsprot), Solaris ar (found in SUNWbtool),
gnu tar, and gnu cc both from sunfreeware.com (I love pkg-get ^_^)
either add /opt/sfw/bin/ to your path or put a dynamic link for gcc into /usr/local/bin/ I prefer the latter.
and add /usr/ccs/bin/ to your path permanently.
Thanks for your help every one.

Recent repair has installed 10.9.1, now unable to sync existing email in outlook to iPhone via iTunes as previously.any advice please

Recent repair has installed 10.9.1, now unable to sync existing email in outlook to iPhone via iTunes as previously. any advice please

It is no longer possible, read the posts under the heading More Like This for workarounds.
Also, check this thread, it's a bit long, and a bit stormy but there is at least one alternative method in posted in it.

After installing Ableton 9, I am unable to open Logic 9 now. How to fix?

After installing Ableton 9, I am unable to open Logic 9 now. How to fix?

Well, Ableton was a crack version, which worked fine. I've since uninstalled it and still get this error message: The Application Logic Pro can't be opened-1712

Ever since I installed Mavericks I've been unable to edit Numbers spreadsheets. Any help.

Ever since I installed Mavericks I've been unable to edit Numbers spreadsheets. Any help.

There is not enough information in your question to guess what the problem might be.
Jerry

Solaris 10 install on an HP dl320 - unable to

Similar Messages

Maybe you are looking for