Solaris 10 installation gives error "No disk Found"

During the installation of Solaris 10 on dell XPS400, it gives error that says no Disk found:
I have already partitioned by disk in the following manner:
1st partition: 30 GB: NTFS (WIn XP installed)
2nd Partiion: 20 GB: NTFS (data)
3rd Partition: 25GB: RAW
is there any special setting that I need to do for Solaris to detect the hard disk.
Please help!

I do not think you need a driver for the disk.
... you need to reconfigure your system with respect to the DISK CONTROLLER.
Solaris 10 "doesn't do Serial ATA very well".
Search the forum, keyword sata and then read and read and read.
I believe you need to reconfigure something in the PC's BIOS.
However, that may have an impact on how well your current install of WinXP works.
So, I suggest you just go get an additional disk, a conventional IDE drive (not a SATA disk),
and install to that new drive instead.
Then you choose whichever device you want as the boot drive each time you power it on.
... or just go get an older, used computer and dedicate it to operating systems other than Windows. Leave the Dell system alone.
Install... erase ... install something else ... erase ...
etc, etc, etc

Similar Messages

  • Error No disks Found during Solaris 10 installation

    Hi,
    i am trying to install Solaris 10 x86 on an Ml370 server that we bought. during the installation it gives the error No Disks Found. how can i correct this problem?

    One question:
    Does this server ,ML370 G5, support Solaris in 64 bit mode?
    http://www.sun.com/bigadmin/hcl/data/systems/details/1891.html doesn't indicate if it is certified for 64 bits.
    and http://h71028.www7.hp.com/enterprise/cache/493913-0-0-0-121.html indicates ony 32 bits.

  • Whenever i put my iphone for restoration itunes gives error that disk is full what do i do?

    whenever i put my iphone for restoration itunes gives error that disk is full what do i do?

    Is your PC disk full?

  • Installation encountered errors: Actionlist not found

    What should I do to correct "Installation encountered errors: Actionlist not found", when attempting to load Reader XI?

    You may try downloading the offline Reader installer from
    http://get.adobe.com/reader/enterprise/

  • Since upgrading to ios 8.0.2, airprint will give error (no printer found" After a reboot, it locates and prints, then next time same error code. Any ideas?

    Since upgrading to ios 8.0.2, airprint will give error (no printer found" After a reboot, it locates and prints, then next time same error code. Any ideas?

    Hi bdtcop,
    I understand that you are experiencing an issue with AirPrint. Here is an article for you with some troubleshooting steps that may be helpful for resolving this issue:
    About AirPrint
    http://support.apple.com/kb/ht4356
    If you're unable to print
    Check these things if you are unable to print, or if you see the message "No AirPrint Printers Found."
    Make sure your printer has paper, and enough ink or toner installed.
    Make sure your printer is connected to the same Wi-Fi network as your iOS device.
    Make sure your printer has power and is turned on. Try turning your printer off and then back on again to see if it resolves your issue.
    Check to see if your printer has any error lights or indicators displayed on the printer's control panel. Check the documentation that came with your printer to clear any errors displayed.
    Check with your printer's manufacturer to see if any firmware updates are available for your printer. Check your printer's documentation or contact the printer vendor for more information. A firmware update may be available, even if you just bought your printer.
    Thanks for using the Apple Support Communities. Have a good one!
    -Braden

  • SCOM Reporting Server Installation Give Error The specified SQL Server instance is not valid

    Hi All,
    I am trying to install SCOM 2012 SP1 Reporting Server on a Windows Server 2012 running SQL Server 2012 SP1. The SQL Server also host instance for SCCM 2012 SP1 named SCCM, and not in clustered environment.
    For SCOM 2012 SP1, I choose SQL instance named SCOM. At first, I successfully installed SCCM 2012 SP1 Reporting Services. I have SSRS configured to use port 80 for both SCCM and SCOM instance, and not using SSL, with IP Address settings: All assigned. SQL
    Server Agent services on both instances are configured to started automatically. I could access http://scsqlserver/reports_SCCM and http://scsqlserver/reporserver_SCCM, but could not for http://scsqlserver/reports_SCOM and http://scsqlserver/reporserver_SCOM. 
    On OpsMgrSetupWizard.log give error
    [12:24:53]: Error:
    :CheckHttpAddressResponse failed: Threw Exception.Type: System.Net.WebException, Exception Error Code: 0x80131509, Exception.Message: The remote server returned an error: (500) Internal Server Error.
    [12:24:53]: Error:
    :StackTrace:   at System.Net.HttpWebRequest.GetResponse()
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.ReportingComponent.CheckHttpResponseFromSRSUrl(String httpSite)
    I may continue Reporting Server installation that give no error mentioned above, if I choose SSRS instance named SCCM, but it is not supported for both SCCM and SCOM 2012 using same SSRS instance. Personal certificate for ConfigMgr SQL Server Authentication
    on SQL Server has been exported and deleted. Restarting SQL Server also has been done, but no luck.
    Many thanks for your help.

    Hello,
    I'm afraid you must use a dedicated instance of SQL Server for each site(SCOM/SCCM). Some similar issues were disscussed on this forum:
    SCCM and SCOM - SQL Server 
    http://social.technet.microsoft.com/Forums/en-US/configmanagergeneral/thread/bfa14da9-4692-4c64-a107-e085c967d259
    SCOM, SCCM, SQL on same server?
    http://social.technet.microsoft.com/Forums/en-US/configmgrsetup/thread/b5373aa7-5233-4b1f-9b39-b86e481e04d5
    Thanks,
    Yog Li
    TechNet Community Support

  • Installer gives error. [osx]

    Hi,
    Just trying to install latest flash, using latest installer file.
    But when I run the installer, it gives error: "Unable to load application configuration".
    I have redownloaded installer file, couple days a go, yesterday and today. Didn't help.
    I'm running osx 10.8.3.
    File permissions are fixed.
    Firewall on/off, tested.
    Thanks.

    Looks like that there are lot of problems with installer on OSX.
    I managed to install 11.7 using offline installer, http://fpdownload.macromedia.com/get/flashplayer/current/licensing/mac /install_flash_player_11_osx.dmg .

  • Adobe flash player installer - installation encountered errors - Actionlist not found

    adobe flash player installer - installation encountered errors - Actionlist not found

    Download the "offline" installer, Save it to your downloads folder, and run it after a reboot.

  • FB 4.5 Premium installer gives error 1603

    Downloaded Flash Builder 4.5 premium from the Adobe site, used Application Manager to create a deployable package.  It bombs out with a 1603, no hints at all in the 237 kb log file as to why.  Google isn't helping.

    Trying to install FB 4.5 - comes up with this error on my machine - anyone have any concrete ideas on how to overcome this...
    I've tried rebooting, removing activex plugins etc but of no help....
    WARNING: DW031: Payload:{650C9D09-D5BD-4532-8BEE-01DBC1DF5537} Adobe Flash Builder 4.5 4.5.0.0 has been updated and has been selected for repair. The patch {CEAC4FFA-E7DE-4434-890A-F0AC7792DE5E} Adobe Flash Builder 4.5_4.5.1_AdobeFlashBuilder-mul 4.5.1.0 will be uninstalled now.
    WARNING: DW031: Payload:{650C9D09-D5BD-4532-8BEE-01DBC1DF5537} Adobe Flash Builder 4.5 4.5.0.0 has been updated and has been selected for repair. The patch {CEAC4FFA-E7DE-4434-890A-F0AC7792DE5E} Adobe Flash Builder 4.5_4.5.1_AdobeFlashBuilder-mul 4.5.1.0 will be uninstalled now.
    ----------- Payload: {551D0A52-5E4A-4898-9FFF-FEAA5E89585A} Adobe Flash Player 10 ActiveX 10.0.0.0 -----------
    ERROR: Error 1722.There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor. Action NewCustomAction1, location: C:\DOCUME~1\nanunh\LOCALS~1\Temp\InstallAX.exe, command: -install activex -msi
    ERROR: Install MSI payload failed with error: 1603 - Fatal error during installation.
    MSI Error message: Error 1722.There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor. Action NewCustomAction1, location: C:\DOCUME~1\nanunh\LOCALS~1\Temp\InstallAX.exe, command: -install activex -msi
    ERROR: DW050: The following payload errors were found during install:
    ERROR: DW050:  - Adobe Flash Player 10 ActiveX: Install failed
    Please search the above error/warning string(s) to find when the error occurred.
    These errors resulted in installer Exit Code mentioned below.
    Exit Code: 6 - Silent workflow completed with errors.
    [    1460] Mon Aug 15 17:52:20 2011  INFO
    *=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=

  • During Itunes installation gives error:  Could not write value ManageLL....

    Hi,
    I have 2 PCs at home and on one itunes installed just fine but on another during installation i am getting the following error:
    Could not write value ManageLLRouting to key \System\CurrentControlSet\Services\Bonjour\Service\Parameters
    Anyone has an idea? Google didnt give me anything on such issue.
    Will appreciate your help.

    Hi clinton86,
    Welcome to the Apple Support Communities! I understand that are receiving an alert when trying to import a CD to iTunes and are being asked to reinstall iTunes. iTunes and all of its components must be removed in a specific order when uninstalling from a Windows computer. Please use the following article as a reference.
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    http://support.apple.com/kb/ht1923
    1. Remove iTunes and related components from the Control Panel
    Use the Control Panel to uninstall iTunes and related software components in the following order and then restart your computer:
    iTunes
    Apple Software Update
    Apple Mobile Device Support
    Bonjour
    Apple Application Support (iTunes 9 or later)
    Important: Uninstalling these components in a different order, or only uninstalling some of these components may have unintended affects.
    I hope this helps,  
    -Joe

  • New Relic APM installation gives error

    I can't seem to add the New Relic APM extension anymore. I wanted to add it to two VM's that were already created. Because I didn't New Relic offered it directly through the new portal I tried creating it using the NewRelic Azure packages. When this didn't
    work I found out about the direct way using the new portal, which worked on VM1 and not two. Going to two I saw that NewRelic was still installed on 2 in the old way, removed it, removed the generic New Relic APM, removed it from server 1 and gave both a reboot
    so I'd start with a clean slate and do it perfectly right this time. The two VM's seem perfectly fine, but I can't seem to add it to my subscription anymore.
    I get two failed events besides the Microsoft Resources event that notifies me of the failure of the deployment:
    NewRelic.APM/Accounts/write 2x
    with error message: 
    statusCode:NotFound statusMessage:{"error":{"code":"BadRequest","message":"\n<hash>\n <error>The requested page could not be found</error>\n</hash>\n"}}
    Any thoughts?

    Hi,
    I understand that you are unable to add New Relic APM Extensions through the New Portal and unable to associate with your subscription.
    You might want to refer to the below link which explains about creating New Relic APM Account in the New Preview Portal
    https://docs.newrelic.com/docs/agents/net-agent/azure-installation/azure-preview-portal
    If the issue still persists, Suggest you to raise a Billing Ticket for the same by following the below link
    http://azure.microsoft.com/en-us/support/options/
    Hope this helps !
    Regards,
    Sowmya

  • HT1428 Log into FileVault gives error on disk try again later. This is only account on system how do I log in to do disk repair. MacBook Pro running lion

    Only have 1 account on MacBook Pro. Protected by FileVault. Log in  says your home folder didn't open. It needs repaired. We click ok. Unable to login to account at this time.  Account failed because error occurred.   Everything I have read so far has me doing things from the finder but I can't get into the program. This happened after I did an update last night  and it asked to restart system. I have it backed up on external drive through time machine but I can't get in to use it.

    Hey Sky42,
    Thanks for the question. The following resource may help to resolve your issue:
    Resolve startup issues and perform disk maintenance with Disk Utility and fsck
    http://support.apple.com/kb/ts1417
    Thanks,
    Matt M.

  • Solaris 10 Gives Error (ld: fatal: relocation error: R_386_32) w/ gcc-4.2.3

    I am attempting to run a build of a system known as nauticus under Solaris 10 but I am getting the following error:
    ld: fatal: relocation error: R_386_32: file .rel.debug_info: section: /home/dmclaug/trees/gcctree/trunk/build-solaris-4.2.3/src-nauticus/bin/solaris/libsmftypes.o: offset: 0x23e3d6: relocation requires reference symbol
    collect2: ld returned 1 exit status
    This system has been successfully built using gcc-3.2.3 under Solaris 10, but the error above is generated now that we have installed gcc-4.2.3. Does anyone have any idea what might be causing the problem here? Are there additional flags or switches that are required?
    Some additional background on my system:
    Sun Microsystems Inc. SunOS 5.10 Generic January 2005
    Sun Streaming Server Development Package for Solaris Update 4.
    PackageVersion=2.0
    cat /etc/release
    Solaris 10 8/07 s10x_u4wos_12b X86
    Copyright 2007 Sun Microsystems, Inc. All Rights Reserved.
    Use is subject to license terms.
    Assembled 16 August 2007
    isainfo -x
    amd64: sse3 sse2 sse fxsr amd_3dnowx amd_3dnow amd_mmx mmx cmov amd_sysc cx8 tsc fpu
    i386: sse3 sse2 sse fxsr amd_3dnowx amd_3dnow amd_mmx mmx cmov amd_sysc cx8 tsc fpu
    isalist
    amd64 pentium_pro+mmx pentium_pro pentium+mmx pentium i486 i386 i86

    The bootstrap compiler is GCC 3.4.3.
    I tried Sun's assembler (/usr/ccs/bin/as) too and got another error (below)
    I also tried bootstrapping with Sun's Studio 12 compiler but that too failed.
    *$ pkginfo -x SUNWbinutils SMCbinut*
    SMCbinut binutils
    (x86) 2.17
    SUNWbinutils binutils - GNU binutils
    (i386) 11.10.0,REV=2005.01.08.01.09
    *$ whence gcc*
    /usr/sfw/bin/gcc
    *$ gcc -v*
    Reading specs from /usr/sfw/lib/gcc/i386-pc-solaris2.10/3.4.3/specs
    Configured with: /builds/sfw10-gate/usr/src/cmd/gcc/gcc-3.4.3/configure prefix=/usr/sfw with-as=/usr/sfw/bin/gas with-gnu-as with-ld=/usr/ccs/bin/ld without-gnu-ld enable-languages=c,c++ --enable-shared
    Thread model: posix
    gcc version 3.4.3 (csl-sol210-3_4-branch+sol_rpath)
    The error this time is:
    /big1/usr.local.src/gcc-4.3.1/s10i/./gcc/xgcc -B/big1/usr.local.src/gcc-4.3.1/s10i/./gcc/ -B/usr/local/i386-pc-solaris2.10/bin/ -B/usr/local/i386-pc-solaris2.10/lib/ -isystem /usr/local/i386-pc-solaris2.10/include -isystem /usr/local/i386-pc-solaris2.10/sys-include -g -fkeep-inline-functions -m64 -O2 -O2 -g -g -O2 -DIN_GCC -W -Wall -Wwrite-strings -Wstrict-prototypes -Wmissing-prototypes -Wold-style-definition -isystem ./include -fPIC -g -DHAVE_GTHR_DEFAULT -DIN_LIBGCC2 -D__GCC_FLOAT_NOT_NEEDED -I. -I. -I../../.././gcc -I../../../../gcc-4.3.1/libgcc -I../../../../gcc-4.3.1/libgcc/. -I../../../../gcc-4.3.1/libgcc/../gcc -I../../../../gcc-4.3.1/libgcc/../include -DHAVE_CC_TLS -o gcov.o -MT gcov.o -MD -MP -MF gcov.dep -DLgcov -c ../../../../gcc-4.3.1/libgcc/../gcc/libgcov.c
    Assembler: libgcov.c
    "/var/tmp//ccYcw90K.s", line 1936 : Syntax error
    Near line: " repz cmpsb"

  • Installation gives error against core40.dll

    Hello,
    I'm trying to install dev 6.0. However when I try and install it I get an informational message that I have to close all Oracle applications cause there's an application using the core40.dll.
    When I check for an Oracle application there appears to be none running. Even when I check using Oradim80.exe the only application that appears to be running is the oradim80.exe. Except off course the Oracle installer.
    I'm using the Y2K compliant orainstall.
    Can anybody tell what's causing this problem??
    Thanks

    1. Try removing any references to the OraWin95/OraNT path on autoexec.bat/NT environment
    2. Reboot the machine
    3. Install Dev6
    4. Rewrite the Orawin95/OraNT references on autoexec.bat

  • Firefox will open a 1Mb PDF file. With 30Mb PDF file Firefox gives error "File not found". Both PDFs from Adobe web site. Using PC with XP-sp3. Firefox 3.6.13

    Option in "Tools/Options/Applications/Adobe Acrobat Document" is set to "use Adobe Acrobat in Firefox". If I change the option to "Use Adobe Reader 9.2 (default)" then the large file gets downloaded and then opens in Reader.
    Any help appreciated.

    I originally posted this nearly 2 months ago. Is no-one else having this problem...???
    I upgraded to Firefox V3.6.16; problem still happening.
    Anyone got any ideas please...???

Maybe you are looking for