Solaris 10 network status shows 'disconnected' & cannot ping out

Hi,
In my solaris 10 sparc t4-1 server, the network status shows 'disconnected'
I cannot ping to any servers in the lan.
Please help
thanks

Sounds like it's either infrastructure or faulty hardware. Are you sure the port is turned on that you are plugging into?

Similar Messages

Outlook and OWA shows disconnected intermittently while on corporate wi-fi

Hello All,
We have exchange 2013 Std on-premises with Service pack1. When users connect from LAN and Datacard they able to connect to outlook and access OWA and when from office wi-fi network outlook shows disconnected and not able access OWA as well but internet works
fine. this issue happening intermittently with office wi-fi.
Regards,
Aayan

Hi Aayan,
From your description, when users connect from LAN and Datacard they are able to access Outlook and OWA, then there is nothing wrong with Exchange server side. In your case, this disconnected issue only occurs when you use wifi network, I recommend you check
your network when using wifi.
Hope this can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support

Cisco ASA 5505 Cannot ping local traffic and local hosts cannot get out

I have, what I believe to be, a simple issue - I must be missing something.
Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209).
There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off.
The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue.
Basically, the VPN is up and running but PC 10.51.253.210 cannot get out.
Any ideas? Sanitized Config is below. Thanks !
ASA Version 7.2(4)
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif Inside
security-level 100
ip address 10.51.253.209 255.255.255.248
interface Vlan2
nameif Outside
security-level 0
ip address ***** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
dns server-group DefaultDNS
domain-name *****
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
pager lines 24
mtu Outside 1500
mtu Inside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any Outside
no asdm history enable
arp timeout 14400
global (Outside) 1 interface
nat (Inside) 0 access-list No_NAT
route Outside 0.0.0.0 0.0.0.0 ***** 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa authentication enable console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
http server enable
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set DPS_Set esp-3des esp-md5-hmac
crypto map DPS_Map 10 match address Outside_VPN
crypto map DPS_Map 10 set peer *****
crypto map DPS_Map 10 set transform-set *****
crypto map DPS_Map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Outside
ssh timeout 60
console timeout 0
management-access Inside
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group ***** type ipsec-l2l
tunnel-group ***** ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8d0adca63eab6c6c738cc4ab432f609d
: end
1500

Hi Martin,
Which way you are trying. Sending traffic via site to site is not working or traffic which you generate to outside world is not working?
But you say ASA connected interface to PC itself is not pinging that is strange. But try setting up the specific rules for the outgoing connection and check. Instead of not having any ACL.
If it is outside world the you may need to check on the NAT rules which is not correct.
If it is site to site then you may need to check few other things.
Please do rate for the helpful posts.
By
Karthik

How to show network status in top toolbar?

how to show network status in top toolbar? Network preferences is there, but network status has disappeared on last reset of Airport Express, but may not be connected. Thanks in advance for practical help

Interestingly, in my experience, using the method described above of unchecking the "Show Connected Servers" box in the Finder Preferences makes no difference in what I can put in the sidebar. I was able to move a sub-folder of a shared disk to the Favorites section of the Finder Sidebar, but nothing else. (i.e. I could not add the shard disk itself to the sidebar – either to the devices, favorites, or any other section, and I could only add a subfolder of the shared disk to the favorites section – not to the devices section or any other section). This was the same whether I had "Show Connected Servers" checked or not.
I'm running OS X Mavericks, and the setup I have is with a previous generation Time Capsule (i.e. the short, square kind that you could buy before the most recent taller variety came out last year), with a LaCie 3 TB USB 3.0 external drive plugged into the USB port of the Time Capsule. I'm then accessing this network drive over WiFi. The differences in what I'm seeing may be due to some change they made in the way Mavericks handles these setups.
I could also just be misunderstanding what you're saying, but I thought I'd add this in case anyone else gets similar results so that they'd know they're not alone. Let me know if I'm missing something here.

Cannot ping windows 2008 r2 while it is possible for another machine in the same network

Hi,
Recently I have set up a new server with windows 2008 r2 enterprise OS which is a domain member server.
At network layer I have two networks one with 192.168.1.0/22 and another with 10.0.0.0/24 network IDs.
My problem is that I cannot ping the newly installed server from a specific machine. Server's IP address is 192.168.1.56 and the specific machine's IP address is 10.0.0.12 and it is a windows XP machine. Of course I have to say that this problem belongs
only to this WinXP machine and all the layer 3 issues are tested and correct. This issue happens while at the same time I can ping domain controller which also is a windows 2008 r2 enterprise box and its IP address is 192.168.1.53. It turns more complicated
when I learned I can ping the winxp machine and connect to it from new server through remote desktop. Firewall also is not the obstacle because I turned it off completely.
Can anybody help me fix the problem?
TIA
Bijan

Hi,
Check the path ping from xp machine to server its timing out after reaching 192.168.1.254 , What kind of a device is 192.168.1.254 IP belongs to.
Tracing
route to sp45newfs.ph45.local [192.168.1.56]
over
a maximum of 30 hops:
0 B15-333.PH45.LOCAL [10.0.0.12]
1 192.168.1.254
2 * * *
Computing
statistics for 50 seconds...
Source to Here This Node/Link
Hop
RTT Lost/Sent = Pct Lost/Sent = Pct Address
0 B15-333.PH45.LOCAL [10.0.0.12]
0/ 100 = 0% |
1 0ms 0/ 100 = 0% 0/ 100 = 0% (192.168.1.254)----------(Which device has this IP)
100/ 100 =100% |
2 --- (100/ 100 =100% )---(100% loss) 0/ 100 = 0% B15-333.PH45.LOCAL [0.0.0.0]
Trace
complete.
Regards,
Srivishnu.K

I have an apple iphone 4 that I want to download audio books from my library onto it. I cannot figure out how to do that. The iphone does not show up on my mac laptop as a connected device. Does this kind of download have to run through itunes? Thanks

I have an apple iphone 4 that I want to download audio books from my library onto. I cannot figure out how to do that. The iphone does not show up on my mac laptop as a connected device. Does this kind of download have to run through itunes? Thanks

Yes it is done through iTunes. The iPhone will never show up in Finder as a device. The following is general information on iTunes sync: http://support.apple.com/kb/HT1386 and the following is a previous discussion where the post by Andreas Junge helped others that had a problem syncing audiobooks: https://discussions.apple.com/message/20052732#20052732

I got a new wireless connection for my mac and cannot figure out how to delete the last connection service I had. Everytime I shut the computer, the network goes back to the other one. I cannot find the file ANYWHERE

got a new wireless connection for my mac and cannot figure out how to delete the last connection service I had. Everytime I shut the computer, the network goes back to the other one. I cannot find the file ANYWHERE

Under Network Preferences, select the WiFi
click on "Advanced..." button
Select the network you want to delete from the list and click on "-"
Click "Ok"
Click "Apply"
Well done ;-)
You may also want to delete the wireless key from Keychain.
Open Keychain, seach for the old wifi network name, slect it and click delete

Hi there can anyone help. I am connected to the internet by ethernet but my connection keeps timing out and my network diagnostics shows all green and network connection ok but still no internet connection. the other wireless laptop in my flat works well.

Hi there can anyone help. I am connected to the Internet by Ethernet but my connection keeps timing out and my network diagnostics shows all green and network connection ok but still no Internet connection. the other wireless laptop in my flat works well. Could the other wireless laptops being used in my flat be affecting my connection. what can I do to get connected, keep connected. Thanks for any ideas out there.

My network connected for a few hours then went back to timing out. I have not changed anything. However there four additional laptop users in my family who do not seem to be having any problems using their wireless connection. Could their film and music downloads be causing the timing out of my connection and if so is there a way I could prioritizes my computer or limit their use?

I have just updated my iPad2 with iOS 6.3.1. and now I am unable to access my home network. The Wi-Fi icon in the status bar is not shown. Under settings, Wi-Fi it shows my network name and under the Wi- Fi menu, chose a Network it shows it is searching f

I have just updated my iPad2 with iOS 6.3.1. and now I am unable to access my home network. The Wi-Fi icon in the status bar is not shown.
Under settings, Wi-Fi it shows my network name and under the Wi- Fi menu, chose a Network it shows it is searching for my network by name and continues to run and run without finding the network.
Prior to updating to iOs 6.3.1 my system worked perfectly.
Can anybody help please.

1. Turn off router for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings

Show ip route shows 'route', but ping times out. Please help.

RouterB,EIGRP 100
s0:152.1.1.1/16
Lo:1.1.1.1/24
no auto-summary]- connected to V35---
[s0/0 RouterA,Lo:2.2.2.2/24,EIGRP AS 100, OSPF Area0, s0/1]/
--- connected to---
[s0/0:192.168.15.2/24
RouterC, OSPF 200,
Area 1]
As you can see in the show ip route from RouterC below, I am able to see a route for 1.1.1.0/24. It is an EIGRP AS redistributed into OSPF.
However, I ping '1.1.1.1' from RouterC, but it times out. Why can't I get to 1.1.1.1 from RouterC ?!
RouterC# Show ip route
1.0.0.0/24 is subnetted, 1 subnets
O E2 1.1.1.0 [110/1000] via 192.168.15.1, 00:04:06, Serial0/0
O E2 152.1.0.0/16 [110/1000] via 192.168.15.1, 00:06:12, Serial0/0
2.0.0.0/32 is subnetted, 1 subnets
O IA 2.2.2.2 [110/65] via 192.168.15.1, 00:06:19, Serial0/0
3.0.0.0/24 is subnetted, 1 subnets
C 3.3.3.0 is directly connected, Loopback0
C 192.168.15.0/24 is directly connected, Serial0/0
RouterC#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Success rate is 0 percent (0/5)

I agree with Sundar that since the route appears in the routing table that you probably do have a viable path to get to 1.1.1.0 and that the problem is most likely lack of a return path.
One way to verify this would be to run debug ip icmp on the router that you are attempting to ping and then do the ping again. If the debug output shows that the ping packets are being received then you have verified that the problem is with the return path.
HTH
Rick

Solaris command to show all network interfaces in a server (plumb/unplumb)?

Hi there,
Is there a Solaris command to show all the network interfaces in a server
(plumb/unplumb etc...).
I have a V880 that has an eri0 on board, plumbed up. It also has a couple
of ge0, ge1, and ce0, and a qfe card.
ifconfig -a only shows eri0.
(I am using something like "dladm show-link", but this is really for
the link-aggregation).
How do I show the remaining network interfaces?
Thanks
Tony

You can see all installed interfaces by running 'grep network /etc/path_to_inst'. An example:
grep network path_to_inst
"/node@1/pci@8,600000/network@1" 0 "ge"
"/node@1/pci@9,700000/network@1,1" 0 "eri"
"/node@1/pci@9,700000/pci@2/network@0" 0 "ce"
"/node@1/pci@9,700000/pci@2/network@1" 1 "ce"
"/node@1/pci@9,700000/pci@2/network@2" 2 "ce"
"/node@1/pci@9,700000/pci@2/network@3" 3 "ce"
"/node@1/pci@9,600000/network@2" 4 "ce"
shows, ge0, eri0, ce0 - ce4

Unable to ship confirm, showing stops cannot be set to status closed

hi all,
while i am performing shipconfirm,
it showing "Error:some deliveries selected for ship confirm have errors or warnings"
and details showing "stops cannot be set to status closed"
appreciate u r best suggestions.
thanks
govardhan

Dear ,
Maybe you need to check all delivery line status ..
All line status should be "Staged.." .
If there is any status not staged, System will show the error.
Hope it's useful to you.

My Mac is showing that I am out of disk space. It says I have 175 MB of videos. I cannot find any videos in Itunes, Imovie or IPicture. What gives?

My Mac is showing that I am out of disk space. It says I have 175 MB of videos. I cannot find any videos in Itunes, Imovie or IPicture. What gives?

For information about the Other category in the Storage display, see this support article. If the Storage display seems to be inaccurate, try rebuilding the Spotlight index.
Empty the Trash if you haven't already done so. If you use iPhoto, empty its internal Trash first:
iPhoto ▹ Empty Trash
Do the same in other applications, such as Aperture, that have an internal Trash feature. Then restart the computer. That will temporarily free up some space.
According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation. You also need enough space left over to allow for growth of the data. There is little or no performance advantage to having more available space than the minimum Apple recommends. Available storage space that you'll never use is wasted space.
When Time Machine backs up a portable Mac, some of the free space will be used to make local snapshots, which are backup copies of recently deleted files. The space occupied by local snapshots is reported as available by the Finder, and should be considered as such. In the Storage display of System Information, local snapshots are shown as Backups. The snapshots are automatically deleted when they expire or when free space falls below a certain level. You ordinarily don't need to, and should not, delete local snapshots yourself. If you followed bad advice to disable local snapshots by running a shell command, you may have ended up with a lot of data in the Other category. Ask for instructions in that case.
See this support article for some simple ways to free up storage space.
You can more effectively use a tool such as OmniDiskSweeper (ODS) or GrandPerspective (GP) to explore the volume and find out what's taking up the space. You can also delete files with it, but don't do that unless you're sure that you know what you're deleting and that all data is safely backed up. That means you have multiple backups, not just one. Note that ODS only works with OS X 10.8 or later. If you're running an older OS version, use GP.
Deleting files inside an iPhoto or Aperture library will corrupt the library. Any changes to a photo library must be made from within the application that created it. The same goes for Mail files.
Proceed further only if the problem isn't solved by the above steps.
ODS or GP can't see the whole filesystem when you run it just by double-clicking; it only sees files that you have permission to read. To see everything, you have to run it as root.
Back up all data now.
If you have more than one user account, make sure you're logged in as an administrator. The administrator account is the one that was created automatically when you first set up the computer.
Install the app you downloaded in the Applications folder as usual. Quit it if it's running.
Triple-click anywhere in the corresponding line of text below on this page to select it, then copy the selected text to the Clipboard by pressing the key combination command-C:
sudo /Applications/OmniDiskSweeper.app/Contents/MacOS/OmniDiskSweeper
sudo /Applications/GrandPerspective.app/Contents/MacOS/GrandPerspective
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window by pressing command-V. You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning to be careful. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The application window will open, eventually showing all files in all folders, sorted by size. It may take a few minutes for the app to finish scanning.
I don't recommend that you make a habit of doing this. Don't delete anything as root. If something needs to be deleted, make sure you know what it is and how it got there, and then delete it by other, safer, means. When in doubt, leave it alone or ask for guidance.
When you're done with the app, quit it and also quit Terminal.

HT4623 I purchased an audiobook in I tunes on my computer, but cannot figure out how to download it on my phone....it always lets me download purchases of movies and tv shows but doesnt show an option for audiobooks

I purchased an audiobook in I tunes on my computer, but cannot figure out how to download it on my phone....it always lets me download purchases of movies and tv shows but doesnt show an option for audiobooks

Oh alright -- I manage to resolve my own stupidity quite abruptly, actually.
Shortly after posting this, I annoying took another gander at iTunes Store settings. To my own idiocy, I must have unchecked "Show iTunes purchases in the cloud" at some point. In my defense, though, the availability of songs in iCloud threw me off quite a lot.
Ha ha -- anyways, if anyone else is having the same problem, check there.

Solaris 10 on M4000 sparc bge link down cannot ping to other

Hi all,
I setup solaris 10 on sun M4000 sparc server, every thing is good when install complete I cannot ping to Gateway from Solaris 10 OS, but on XSCF console I can ping to gateway
SPARCM4000# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge1: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet 172.16.3.235 netmask ffffff00 broadcast 172.16.3.255
ether 0:14:4f:3a:7b:5a
sppp0: flags=10010008d1<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST,IPv4,FIXEDMTU> mtu 1500 index 3
inet 192.168.224.2 --> 192.168.224.1 netmask ffffff00
ether 0:0:0:0:0:0
SPARCM4000#
Any body can help me?

Thanks for quick reply
I've checked already all cables are connected and LEDs light ok, but I don't know whats wrong with M4000 box, Or on XSCF have any command to enables Ethernet cards?
for my XSCF LAN config is :
XSCF> shownetwork -a
xscf#0-lan#0
Link encap:Ethernet HWaddr 00:21:28:6E:88:10
inet addr:10.0.19.235 Bcast:10.0.19.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:62549 errors:0 dropped:0 overruns:0 frame:0
TX packets:2201 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5459443 (5.2 MiB) TX bytes:334404 (326.5 KiB)
Base address:0xe000
xscf#0-lan#1
Link encap:Ethernet HWaddr 00:21:28:6E:88:11
inet addr:172.16.3.223 Bcast:172.16.3.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12616 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1092370 (1.0 MiB) TX bytes:492 (492.0 B)
Base address:0xc000
XSCF> showroute -a
Destination Gateway Netmask Flags Interface
172.16.3.0 * 255.255.255.0 U xscf#0-lan#1
10.0.19.0 * 255.255.255.0 U xscf#0-lan#0
default 10.0.19.1 0.0.0.0 UG xscf#0-lan#0
Regards
Edited by: 986418 on Feb 7, 2013 5:18 PM

Solaris 10 network status shows 'disconnected' & cannot ping out

Similar Messages

Maybe you are looking for