Solaris 10 - print services not running

Hi
One of our servers has just been upgraded from Solaris 9 to 10 but we are having problems getting the lp scheduler to start. We have tried starting the service manually by issuing *'svcadm -v enable application/print/server'* which returns '*svc:/application/print/server:default enabled.*' However when you issue the command '*lpstat -r*' it returns '*scheduler is not running*'. The next step I tried was typing '*svcs -a | grep print*' which returned the following:
online               16:34:09 svc:/application/print/ppd-cache-update:default
online               16:35:39 svc:/application/cde-printinfo:default
offline               16:34:45 svc:/application/print/rfc1179:default
offline               16:34:45 svc:/application/print/ipp-listener:default
maintenance    16:34:45 svc:/application/print/server:default
I then issued the command '*svcs -v -x*' which returned the following:
svc:/application/print/server:default (LP print server)
* State: maintenance since Wed Dec 17 16:34:45 2008*
Reason: Restarting too quickly.
* See: http://sun.com/msg/SMF-8000-L5*
* See: man -M /usr/share/man -s 1M lpsched*
* See: /var/svc/log/application-print-server:default.log*
Impact: 2 dependent services are not running:
* svc:/application/print/rfc1179:default*
* svc:/application/print/ipp-listener:default*
I tried enabling the 2 dependent services manually and it says they are enabled after you issue the command but in actual fact it is not doing anything. Our set up is complicated by the fact that we are not using Soalris as our print m,anager but are using Hewlett Packard's.
Any help would be greatly appreciated,
Bruce

This could be caused by print requests that were waiting in the print queue when the upgrade took place. You need to remove these requests as follows:
# svcadm disable print/server
# rm -fr /var/spool/lp/fifos /var/spool/lp/temp /var/spool/lp/tmp /var/spool/lp/requests
# svcadm enable print/server
# svcs -xv
The print scheduler should now be running and you should now be able to print.

Similar Messages

Auto-start services not running :Shell Hardware Detection in my Health Reports

Recently I've setup up Windows Server 2012 Essentials on my Custom-made Box. All is going well so far except that i have a warning in my generated Health Report such as
Auto-start Services Not Running Shell
Hardware Detection.
I had checked My Services and found out that this particular service is scheduled to start Automatically and it is always started...
Any Advice what might be the problem?

Susan, can you still see the Connect bug? What Product/Program is it under in Connect? I can't see it but I might not be a member of the correct group.
From http://technet.microsoft.com/en-us/library/hh831394.aspx:
"After a server has been added to the Server Manager server pool, service alerts about the Shell Hardware Detection service can be displayed if there are no users logged on to the managed server. This occurs because the Shell Hardware Detection service runs
only when users are logged on to the managed server, or connected to a Remote Desktop session on the managed server. To avoid seeing Shell Hardware Detection service alerts for this case, click
Services in the thumbnails for server groups, including the
All Servers group. In the Services Detail View dialog box, on the
Services drop-down list, clear the check box for Shell Hardware Detection, and then click
OK."
That confirms that it's okay for Shell Hardware Detection not to be running. However the suggested fix--removing it from 2012 alerting--does not keep it off my 2012E Health Report.
Mark Berry
MCB Systems

Diagnostics policy service not running on Windows 7 home premium

I'm unable to connect to internet through wireless connectionsr . it says limited access to wi-fi router. When i try to fix this it says diagnostics policy service not running. Checked services.msc While the type is set up to automatic Unable to start the
service. I had similar problem with my LAN connection. After resetting my LAN connection i was able to connect to internet. Tried this on wifi as well but the issue remains.
Error code is 5: access denied

Hi,
Thanks for the post!
Go to your Device Manager and uninstall the network device, including the wireless network card, then restart the computer. Let the system automatically reinstall the driver for you. You can also manually update the network card driver to the latest one.
After that, check if you can connect to the internet.
For the Diagnostics policy service issue. please click Start, input regedit in the search box, press Enter to open your Registry Editor, navigate to the key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\DPS\Parameters.
Right click this key, choose permission, click the user "Trustedinstaller", ensure the permission is set to "Full Control" and "Read". Then click OK to apply the change.
Restart the computer to check if this service is working now.
Regards,
Miya
This posting is provided "AS IS" with no warranties, and confers no rights. | Please remember to click "Mark as Answer" on the post that helps you, and to click "Unmark as Answer" if a marked post does not actually answer
your question. This can be beneficial to other community members reading the thread.

The Data access service not running or not yet initialized.

Hello guys ,
i am getting the following error wen tryin to open the console The Data access service not running or not yet initialized. on scom 2012 R2 before it was working fine but once i closed the console and open got the error
OS : Windows 2012r2 patched and scom 2012 r2
sql : 2012 r2 enuff database size
tried few things as :
1. change the account to domain admin for system center data acess service still no luck
2. created registry keys for servicepipetimeout to 6000 bt still nit working
3. Refresh sql account used for sccom data aceess service still no luck
4. the service disappears as running after 30 seconds and the console is unable to open
kindly help if some perfect resolution as lot of time has been wasted and need to meet deadlines.
thanks guys in advance
Basit Siddiqui
AIG

Check that following:
Verify permission of SCOM Account on sysadmin and OM DB.
Check firewall that is disable
Check antivirus that didn't block scom folders or services.
Check SQL services is running
Check Space of database at 5 GB as you configured. It is best practice to set the db size at a reasonable size and not to set to autogrowth.
Also you can check below link
http://vmajmudar.blogspot.com/2013/07/the-data-access-service-is-either-not.html
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"Mai Ali | My blog:
Technical | Twitter:
Mai Ali

Window search service not running

window search service not running how i can fix it?
This question was solved.
View Solution.

Hi,
From the Desktop, hold down the Windows key and press

[mostly solved] Strigi service not running

Hello,
Since I am constantly fluctuating between a rich and a minimalistic desktop environment, I'm trying out KDE once again. The Soprano/Nepomuk/Strigi stuff seems really interesting but I fail at using it.
When I go to System Settings -> Advanced -> Desktop Search it says "Strigi service not running". While Nepomuk is activated, I can't activate Strigi. When I set the checkbox for Strigi and apply, the message is still there. When I close the widow and go back again, the checkbox is deactivated again.
The searchbar in dolphin never finds anything and there is no interface for tagging or commenting files.
However, I can index files and find stuff when I run strigiclient.
What may the problem be?
Thanks,
Viv
Last edited by V for Vivian (2010-06-30 07:48:54)

Steigi seems to be installed.
viv ~ $ pacman -Q strigi
strigi 0.7.2-2
I'm considering a clean Chakra installation but this seems kind of unaesthetic and stupid.
edit01: I've just renamed my .kde4 folder and restarted KDE. Now Strigi is indexing and I can tag files, everything works. Some kind of configuration seems to have been wrong. I think I can figure this out.
edit02: I had to replace the .kde4/share/apps/nepomuk folder with a clean one, maybe something with the database or how it is accessed. Don't have time to go into this right now, I'm just happy it works now.
Last edited by V for Vivian (2010-06-30 08:16:11)

Windows Modules Installer - Autostart Service Not Running

I'm receiving in my health reports for four separate WSE 2012R2 deployments the below error. I've set the service to restart upon failure, but it seems this occurs upon every server reboot until I manually go in and start the service. However,
from my understanding this service only runs when it is needed, which would leave me to a false negative in the BPA scan.
Just curious if anyone else is getting this.
Autostart Services Not Running:
Windows Modules Installer

Hi MattSla,
On current situation, please type services.msc in RUN to open Services panel. Then navigate to Windows Modules
Installer service and open Properties. In General tab, please check Startup type of this service. Did set as Manual? Meanwhile, in Log On tab, please check which account this service used to log on as? Did log on as Local System account?
I check the Windows Modules Installer service in two Windows Server 2012 R2 Essentials in my Lab environment.
It seems that this service was set as Manual. Then Generate a Health Report in Dashboard, and didn’t find any error which was related to ‘Autostart Service Not Running’.
If this issue still exists, please open Event Viewer and check if find some relevant events. Those may help
us to go further analyze.
If any update, please feel free to let me know.
Hope this helps.
Best regards,
Justin Gu

Service not running logged an alert?

Hello,
There is a service on a Linux machine I don't want it to run.
I am getting an alert from SCOM:
Alert: SUSE Linux Enterprise Server 11 Process Klog Monitor Alert
Resolution state: New
Source: SUSE Linux Enterprise Server 11 (x86_64)
Path: Server
Last modified by: System
Last modified time: 4/21/2014 6:54:58 AM
Alert description: The KLOGD - Kernel Message Logging daemon on server Server is not running.
I could disable the alert for this service on this server Server but anyway to prevent the server Server to send this information. I know in Windows if the startup type is set to "Automatic" SCOM is looking for a service running, if the Startup
type is set to manual no check.
Do we have the same type of check in Linux?
Thanks,
Dom
System Center Operations Manager 2007 / System Center Configuration Manager 2007 R2 / Forefront Client Security / Forefront Identity Manager

Dom,
Doesn't work the same as Windows. Just override the monitor in the MP and disable it from monitoring the klog daemon.
Regards,
-Steve

SCOM 2012 Linux Monitoring - RPCBIND, RPCIDMAP, RPCSTAT services not running

We are running SCOM 2012 SP1 and added a test Linux server running Red Hat Enterprise 6.3. SCOM is reporting that the server is in Critical health because the following three services are not running.
1) Process Rpcbind Service Health - Rpcbind Mapper Not Running
2) Process Rpcidmap Service Health - NFSv4 ID Name Mapper Not Running
3) Process Rpcstat Service Health - NSM Status Monitor Not Running
My question is that are these services required to be running in order for SCOM to monitor the Linux servers properly? If yes, can you please give brief explaination as to why so I can explain that to our Linux Administrator. The Linux Administrator
is saying that we do not run these services on any of the Linux servers because they are not needed. If infact these services are not needed, how can I have SCOM ignore the critical error messages? Thanks

Yup, generally running. I'm assuming you've done a basic install of RHEL 6. All processes listed above are enabled by default on a RHEL 6 install if you take the default settings. If someone is just getting started you can pretty much guarantee
they will do a basic install of RHEL 6 and this will not be an issue.
Could it be done better... sure but at what point do you stop? We could discover all services running on the system and start monitoring them out of the box but what are important and what are not to each customer? The idea is to give you some basic monitoring
on a default install based on what each OS provider starts on a "default" install. If this does not suite your needs SCOM is very configurable and adding a custom service monitor is very easy to configure along with disabling existing ones.
If you'd like to provide feedback on this feel free to open a support ticket with Microsoft and file what we call a 'Design Change Request' [DCR]. We go though these prior to starting each update to SCOM. No guarantee it will get fixed/changed as we do have
priorities but we are listening.
Regards,
-Steve

Mailbox Server Role Services not running: MSExchangeDelivery

Running Exchange 2013 CU7 on Server 2012R2.
Ive been working on this project on and off for the last few months, as I am the only IT guy, and a new office construction at my company has had me running cable, moving offices, workstations, and phones.
This install of Exchange was working fine up until about a week ago. When I came back to finish its setup, I noticed that I was not able to send email internally anymore. Connecting to OWA says the message was sent, but it never arrives. After some more
investigation, it turns out the MSExchageDelivery service will not run.
Checking on this service, it indicates that it is starting/stopping, but never getting to the running stage. I have tried everything that I can think of, including uninstalling and re-installing the software. I have scoured the internet looking for solutions,
but not finding one that will take care of the problem.
Looking in the event viewer under Windows Logs -> Application I do see alot of information about MSExchangeTransportDelivery. Seems to be looping through a set of events....
1. Error MSExchangeTransportDelivery Failed to start listening (Error: 10048). Binding: 0.0.0.0:475
2. Error MSExchangeTransportDelivery This address is already in use. Binding: 0.0.0.0:475.
3. Error MSExchangeTransportDelivery Inbound direct trust authentication failed for certificate %1. The source IP address of the server that tried to authenticate to Microsfot Exchage is [%2]. Make sure EdgeSync is running properly.
4. Information MSExchangeTransportDelivery The service will be stopped. Reason TCP/IP socket error. The service will stop.
5. Information MSExchangeTransportDelivery A configuration update for Microsoft.Exchange.Transport.TransportServerConfiguration has successfully completed.
6. Information MSExchangeTransportDelivery A configuration update for Microsoft.Exchange.Data.Directory.SystemConfiguration.MailboxTransportServer has successfully completed.
7. Information MSExchangeTransportDelivery A configuration update for Microsoft.Exchange.Transport.X400AuthoritativeDomainTable has successfully completed.
8.Information MSExchangeTransportDelivery A configuration update for Microsoft.Exchange.Transport.AcceptedDomainTable has successfully completed.
9.Information MSExchangeTransportDelivery A configuration update for Microsoft.Exchange.Transport.ReceiveConnectorConfiguration has successfully completed.
10. Information MSExchangeTransportDelivery A configuration update for Microsoft.Exchange.Transport.RemoteDomainTable has successfully completed.
11.Information MSExchangeTransportDelivery A configuration update for Microsoft.Exchange.Transport.TransportSettingsConfiguration has successfully completed.
12.Information MSExchangeTransportDelivery We are doing a full mailbox database reload as part of routing tables loading due to: First read.
Not sure where to go from here... any and all help is appreciated.

You're getting a tcp socket error and This address is already in use. Binding: 0.0.0.0:475.
Are you sure port 475 is not being used for some other service? Go to services and check if the
MSExchangeTransportDelivery is
currently stopped. If it is, open cmd and type netstat -ano and see if port 475 is showing up. If the MSExchangeTransportDelivery
is stopped it should not show up, if it is then it's being binded somewhere else and prob causing a conflict.
James Chong MCITP | EA | EMA; MCSE | M+, S+ Security+, Project+, ITIL msexchangetips.blogspot.com
Thank you for your help. MSExchangeTransportDelivery was stopped. When I ran the netstat command, it shows:
TCP    0.0.0.0:475            0.0.0.0:0              LISTENING       1600
TCP    127.0.0.1:475          127.0.0.1:35056        ESTABLISHED     1600
TCP    127.0.0.1:475          127.0.0.1:35231        ESTABLISHED     1600
TCP    127.0.0.1:475          127.0.0.1:35386        ESTABLISHED     1600
TCP    127.0.0.1:475          127.0.0.1:35559        ESTABLISHED     1600
TCP    127.0.0.1:475          127.0.0.1:35657        ESTABLISHED     1600
UDP    0.0.0.0:475            *:*
1600
So we can see that 475 is indeed in use. I followed this up with Process Explorer to find out what process had PID 1600. Turns out that a security dongle we use for network licensing is using that port. I will be moving the dongle to another server, and
will follow up here when I have results.

IPhoto printing service not available in Australia?

Has anyone heard any news as to why the iPhoto printing service is not available in Australia? It's very disappointing as this was a great selling point to me, I just presumed that it may take time to set up, but still nothing...
I can still print calenders, cards & prints off my home printer of course, but it's not the same as professional printing. It seems a shame as the software costs the same for everyone, but we have features that we can't use.
Does anyone know why this is?
Cheers!
emac 1.42GHz PPP G4 Mac OS X (10.4.7)

No comment on why Apple has not made this service available themselves in Australia, but there are a number of other options. For the ultimate in convenience and excellent quality, you can use digitaldavinci.com.au. They have an iPhoto plugin which will let you send books, cards and calendars to them. So this is pretty much the same as the Apple service anyway, although I think - but haven't checked myself - that the price is a bit higher.
Alternatively, I have had very good results sending a PDF of a book to myreflections.com.au. This is obviously not quite as convenient, but the quality is still very good and the price even better.
So there are definitely printing options available from iPhoto, especially for books, not so much for prints, and at least one option I know of for calendars and cards. I haven't used the calendar or card service though, just the book printing service from both DDV and MyReflections.
Hope this helps.

Intel RST Service Not Running

PLEASE HELP
Since updating from Windows 8 to 8.1 I am experiencing performance degradation on my HP HPE-250f desktop PC (one HDD, NO RAID).
In the past (Win 7 & 8), when I would occasionally notice performance degradation, the Intel RST icon in the system tray would have a yellow triangle with an exclamation mark in front of it and if I would hover over it, it would say “Intel RST service is not running”. I would then reboot the PC and performance would return to normal.
Since updating to Win 8.1 everything stated in the previous paragraph is still true, except nothing changes after the reboot.
I’ve tried right clicking on the RST icon and then opening the IAStorUI program, but the message “IASrorUI has stopped working” flashes on the screen then disappears and nothing changes.
Any help solving my problem will be appreciated.

Hi,
Some versions of IRST have delayed startup. This improves the startup time to get the desktop displayed.
Try the lastest version of IRST.
I have never experienced an performance degradation due to a delayed IRST startup. However, your mileage my vary.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Windows Audio service not running

I have just built my new computer, and I loaded up windows on it, and everything is working fine but the audio. I have the X over the audio and the "audio service is not running" error. I tried to start The Windows Audio service in the service
menu, but when I do that, I click the audio button and the red X reappears. I know I have all the dependant services enabled, because I have read through many forum posts. So, just to sum things up, all dependant services are on, I get the X error, and whenever
I start the Windows audio service it seems like its working but when I click the volume bar the X reappears over the icon.

Hello,
I recommend reposting your question in one of the Windows forums, depending on which OS version you are running. For example, either Windows 7 IT Pro or Windows 8.1 IT Pro forums.
- Christopher
Until the Whole World Hears

Platform Service not running - Windows 7 Ultimate 32bit

Network Magic v5.5.9195.0 tells me that the platform service is not running - however the Services snap in says that it is and alows me to stop and start it, but NM still tells me it is not running - it was working fine until a few days ago and has suddenly stopped..
Any ideas?
Regards

Apologies I appear to have hit the wrong key and posted rather than next lined
The event log has the following entry whenever I attempt to start the service either automatically or manually:
Faulting application name: nmsrvc.exe, version: 11.2.9170.0, time stamp: 0x4a3c0a3f
Faulting module name: ntdll.dll, version: 6.1.7600.16559, time stamp: 0x4ba9b29c
Exception code: 0xc0000005
Fault offset: 0x00022262
Faulting process id: 0x10f4
Faulting application start time: 0x01cbae50d400fae5
Faulting application path: C:\Program Files (x86)\Common Files\Pure Networks Shared\Platform\nmsrvc.exe
Faulting module path: C:\Windows\SysWOW64\ntdll.dll
Report Id: 47565619-1a44-11e0-beb3-00241dd23cce
Did you ever get a resolution to this problem?
The problem started when I changed my router and Network Magic had to rebuild my configuration. Since then I have been unable to load a stable version of NM however many timkes I de-install/re-install
PS
I have Gigabyte EP43-UD3L motherboard, 4GB memory, 1GB LAN link, ADSL2+ with ST516V6 router/modem and a number of NAS devices & Netgear Professional gigabyte switches
Derek GC White - Running Network Magic version -5.5..9195.0-Pure0 on Windows 7 x64 Home Premium on Wired Computer with Kasperky Internet Security (latest version)
1GB Realtek PCIe NIC v 7.34.1130.2010 via Netgear GS105 Hub to Netgear GS108 Hub to Netgear SRXN3205 WiFi VPN Router to Draytek Vigor120 ADSL2+ "modem"
GA-Z68XP-UD3, 8GB G.Skill Ripjaw DDR3
RAID0 - 2 x OCZ Vertex 3 SSD
RAID5 - 3 x 1TB Samsung Spinpoint F3 accelerated by 1 x Runcore mSATA SSD
RAID 1 - 2 x 500GB Hitachi
2 x ATi HD5750 Crossfire

SMF and multi-user service not running

Hi,
I have an issue with several services not starting ...
As you can see, the multi-user services is "offline*" And it remains like this...
I've recently patched the system hoping it would resolve this issue, but no luck. Restarting the server does not help.
# svcs | grep multi-user
offline 14:14:21 svc:/milestone/multi-user-server:default
offline* 14:14:53 svc:/milestone/multi-user:default
# svcs -xv
svc:/milestone/multi-user:default (multi-user milestone)
State: offline since Wed Dec 05 14:14:53 2007
Reason: Start method is running.
See: http://sun.com/msg/SMF-8000-C4
See: man -M /usr/share/man -s 1M init
See: /var/svc/log/milestone-multi-user:default.log
Impact: 6 dependent services are not running:
svc:/system/webconsole:console
svc:/milestone/multi-user-server:default
svc:/system/basicreg:default
svc:/system/zones:default
svc:/application/graphical-login/cde-login:default
svc:/application/cde-printinfo:default
I've tried to enable the services above manually, but had no luck.
Thanks.

Darren_Dunham wrote:
>
# svcs | grep multi-user
offline 14:14:21 svc:/milestone/multi-user-server:default
offline* 14:14:53 svc:/milestone/multi-user:default
# svcs -xv
svc:/milestone/multi-user:default (multi-user milestone)
State: offline since Wed Dec 05 14:14:53 2007
Reason: Start method is running.The start method of milestone/multi-user is responsible for (among other things), running all the /etc/rc2.d scripts. If you've placed a startup script in there and it's hanging, you'll see this behavior. From memory, I think there's a 30 minute timeout before it gives up and continues.
During the problem period, you probably want to do a 'ps -ef | grep rc' and look for any rc scripts running. That will probably point to a startup script hanging.
DarrenThanks Darren,
That was the problem. A hung script in rc2.d/
What is odd, is that this script is the same on many of our machines and no problems have been found until now. Thanks for your help. Killing that processes made everything start properly.

Solaris 10 - print services not running

Similar Messages

Maybe you are looking for