Solaris 10 - problem installation VMware

SunOS Release 5.10 Version Generic_141445-09 32 -bit
Copyright 1983-2009 Sun Microsystems, Inc. Allrights reserved.
Use is subject to license terms.
panic[cpu0]/thread=fec20160:page_unlock:page fe386f80 is not locked
is it a report during setting in Vmware 6, that to do?

Perhaps you should go ask the people at VMware . *<- link*
It is their product that is having the problem with Solaris.
VMware has a technical support department and they also have their own online discussion forum.
( Would be asking Microsoft if you saw a similar issue with VMware and Windows? I think not.)

Similar Messages

Solaris 8 installation problem on an Intel base PC

I'm quite new with Solaris. I got stuck in Solaris 8 installation just at almost the very beginning. After booting up the system from floppy and conituing pressing F2 and selecting booting from CD, I got an error message like:
cannot mount on pci@0; 0/pci-ide@7; 1/ide01/sd@0; 0:a
panic[cpu0]thread=FEC17440 vfs:mountroot
then, the system reboots itself again and again every time it reaches this point. I guess it's a problem with my CD-ROM. But the problem persists even if I change CD-ROM or move CD-ROM from secondary master to primary slave, etc. I also tried to change harddisk, but did no good to the problem. Is there any experienced users who could provide me with some solutions?
I'm using a system with: Pentium 133, 32 MB Ram, 4GB HDD, 3C905TX, ATI Rage II PCI, Matshita CR-587 CD-ROM, Serial mouse and so on. I also tried another system with: P III 450, Asus P3BF, 192MB Ram, Pioneer DVD-ROM, same HDD, and so on. The problem was still there with the latter system. However, I successfully installed Solaris 7 with the latter system before. Why can't it work with Solaris 8?
Thanks a lot for the help.

I've been having the exact same problems on a PowerEdge 500SC. I have managed to get Solaris up and running on the machine, however. I booted the DCA from the floppy disk and installed from the CD-ROM. When the DCA is ready to scan for devices I use the "Specific Scan" option to tell it to look for specific devices. I tell it to scan for all devices in the listing and in doing so the DCA finds ISA-based IDE controllers. After it provides a listing of the devices it found I use the "Device Tasks" option and the "View/Edit Devices" menu item then delete the Bus Mastering IDE controller device. Once the screen comes up to ask for a boot device, the drives will show up as on the ISA controllers.
I have to go through this process every time I boot the machine but I am able to make the system run at least.
I haven't figured out the ACPI problem, yet.
Regards,
Doug

[Solaris 10] Installation problem on nForce4 Ultra - SATA II - raid 0

hi,
Like I was read on HW web page, Solaris 10 should work fine with 'nForce4' (without 'Ultra'),
but on mine mainboard (nForce4 Ultra) instalator was unable to found my array.
I have ASUS A8N-E (nForce4 Ultra) with 2x 250GB Seagate on SATA II RAID 0.
Is it posible to install this OS on 'nForce4 Ultra' or maybe I am doing sth wrong ?

Hi, I have the similiar problems on Solaris 10 installation.
I have a Compaq SR1710 AMD Sempron™ + 1GB RAM. I am trying make it a mini workstation.
However, the installation was never able to throught.
It always stop or freeze on the "dos" screen after I select "interactive" installation.
The last error message I got was something "Skipped rtls01" something.
I am trying to install Solaris 9 now, so far on disc 2.
Very smooth. No problem..
hope someone can give me advise on how to install version 10 on the machine.
BTW, I checked teh HCL. It seems ok, given my machine is very basic.

Problem in installing Solaris 10 under VMware

I am installing Solaris 10 under VMware (VMware ESX 2.5.1) but after it skipped configuring the interface pcn0, nothing comes up on my window again.

help me!
I have them same problem!
Thanks!

Installation of Solaris 10 on VMware and on external HDD

Greetings,
I am having laptop , having 512 MB RAM, AMD Turion 64 processor.
I purchased a new external HDD, I want to install VMWARE and then I want to install solaris 10 in VMWARE on my external HDD.
I want your suggestion that whether I can install solaris 10 on this configuration and if I can configure can I configure Oracle 11g software???
As of I am new to this one, your suggetions will be so helpful for me.
Thanks & Regards
Kaushal.

user8856758 wrote:
Greetings,
I am having laptop , having 512 MB RAM, AMD Turion 64 processor.
I purchased a new external HDD, I want to install VMWARE and then I want to install solaris 10 in VMWARE on my external HDD.
I want your suggestion that whether I can install solaris 10 on this configuration and if I can configure can I configure Oracle 11g software???
As of I am new to this one, your suggetions will be so helpful for me.
Thanks & Regards
Kaushal.(1) To be blunt you dont have enough RAM for starters. You might get aware with 2GB, you probably really need 3GB or perhaps 2.5GB might just do.
(2) VMware is a company who produce several products, i assume you are talking about VMware server ... but I may be wrong.
(3) I assume you are retaining a windows OS on your laptop., but again i could be wrong.
Its not really in my nature to have Oracle Databases on external USB drives, but this stack will probably just work. (Simply because VMmare server will use a simply file for its virtual disk(s) on the USB)
I would also not be surprised if you has issues with the Solaris graphics.
In general I suspect your auggested setup may be at the least troublesome.
What I have said above are opinions, it is not fully researched and I accept corrections.

Problem with USB - solaris 10 on VMware

I am running solaris 10 on VMware and I do not know how to setup the USB drive. After refer to few doc from sun still unable to get what i should do.
Can someone help?
On VMware I have added a USB controller.
Oh yes, from prtconf and dmesg, it don't seem to reganize the usb controller. I believe I have to make the system to recognise the USB first.
# prtconf| grep USB
# prtconf| grep usb
# dmesg |grep usb
below are the vfstab config
# more vfstab
#device device mount FS fsck mount mount
#to mount to fsck point type pass at boot options
fd - /dev/fd fd - no -
/proc - /proc proc - no -
/dev/dsk/c0d0s1 - - swap - no -
/dev/dsk/c0d0s0 /dev/rdsk/c0d0s0 / ufs 1 no -
/dev/dsk/c0d0s7 /dev/rdsk/c0d0s7 /export/home ufs 2 yes -
/devices - /devices devfs - no -
ctfs - /system/contract ctfs - no -
objfs - /system/object objfs - no -
swap - /tmp tmpfs - yes -
#

On pre 6.0 vmware you can't use usb because support of solaris 10 by this version is experimental and no support tools available.
On 6.0 and later, its maybe work.
Edited by: [email protected] on Dec 11, 2007 8:43 PM

Solaris 10 installation freezes

Hello
im trying to install solaris 10 on a Sun ultra 10, but everytime i come to the language selection it just freezes and dont respond, if i press stop+a i get a prompt.
any one have any clues?
Cheers
Martin

Have you tried text-mode (non-gui) installation?
I do installation of Solaris 10 on VMWare many times, but I never had the problem you describe although I usually do text-mode installation since I don't have much memory assigned to Solaris 10. hopefull, this works for you.

Not able to add driver update during Solaris 10 installation on IBM x3550

I am facing a problem with installation of Solaris 10 on IBM x3550.
My question is not specific to IBM server.
I am trying to add SAS driver during Solaris 10 installation. I selected option "Apply device driver update" (option # 4). It is asking to insert driver disk. But only showing floppy (f) and cdrom (c).
IBM server 3550 doesnt have floppy drive and I have the driver image only in a USB stick. Unfortunately, Solaris 10 installation is not showing usb device during driver installation.
Is there any way we can add usb device to the driver update disk list??
Thanks in advance.

Does no one have an idea?

Solaris 8 installation in Dell 8100 met "Resource Confilict"

Hello There,
During I installated Solaris 8 in Dell Dimension 8100, I received the warning message:
"Resource Conflict: both devices are added.
NON-ACPI device:PNP0c01
Port 800-8DF, C00-C7F; Memory FFB00000-FFFFFFFF
ACPI device:PNP0C01
Memory: 9FC00-9FFFF, 3f87000-7F86FFF, FFFB0000-FFBFFFFF, FFC00000-FFFFFFFF."
How can I recovery this "CONFLICT".
Thanks very much !!!
Jack

AFAIK, this is a warning and can be ignored. But on dell
systems there a lot of other problems that can prevent
a successful solaris 8 installation (dell keyboard problems,
problems with a panic when the system include a 3com
3c905c NIC, ACPI problems, ...).
See also:
http://groups.yahoo.com/group/solarisonintel/message/26542
Does it crash/reboot when you continue?
Try to boot from the "Software 1 of 2" CDROM and at the
"1 interactive or 2 custom jumpstart" prompt type "b kadb -v"
instead of "1" or "2". In case it crashes while booting the
solaris kernel from cdrom, this should give some usable
error message...

Sun Fire V490-Internal FC Drives missing in Solaris 10 installation program

Hi,
We have a V490 server that we are attempting to configure, but the internal FC drives are not available to the Solaris 10 installation program.
The OpenBoot SCSI test fails:
{3} ok test-scsi
Testing /pci@9,600000/SUNW,qlc@2
ERROR : ISP2200 RISC engine did not generate expected interrupt.
DEVICE : /pci@9,600000/SUNW,qlc@2
SUBTEST : selftest:loop-tests:inquiry-test:disk-test
CALLERS : (f010f69c)
MACHINE : Sun Fire V490
SERIAL# : 66233440
DATE : 03/27/2012 14:27:32 GMT
CONTR0LS: diag-level=max test-args=
/pci@9,600000/SUNW,qlc@2 selftest failed, return code = 1
but the probe of the SCSI bus does not and displays the drives:
{3} ok probe-scsi
This command may hang the system if a Stop-A or halt command
has been executed. Please type reset-all to reset the system
before executing this command.
Do you wish to continue? (y/n) y
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 500000e010192d11 FUJITSU MAP3147FC 0110
1 1 0 21000014c320ff73 SEAGATE ST314670FSUN146G055A
How can we fix this problem?
Thanks.
S Kayal
Edited by: 923748 on Mar 27, 2012 10:59 AM
Edited by: 923748 on Mar 27, 2012 11:00 AM

I don't think the test-scsi command is viable for that platform.
The FC disks are "viewed" by the system as external to the SCSI controller, almost as if they were in a multi-pack.
They are FC drives addressed by the chipset as SCSI disks.
Try:
<pre>probe-scsi-all</pre>
Edit:
Which release of Solaris 10 are you trying to install?
Older releases that might be fine for V480's won't work on V490's.
Edited by: rukbat on Mar 27, 2012 2:35 PM

Solaris 10 Installation CDs

Hi,
I have downloaded solaris 10 installation CDs from site, verified them with checksums and burnt then into 700MB CDs. When I put the first one into CD-Rom and issue "boot cdrom" it prompt smthing like:
there is no executable file ...
What is the problem?

... In MS Windows ...
I double-click an ISO file.
It launches whatever program might be installed on my computer
that is associated with burning-to-disk (Nero, Roxio, Isobuster, whatever).
I pick a speed that I might want this time, such as 8x, and simply proceed.
It just works.
The program figures it all out for me.
That's how I've burned ISO files from all sorts of sources for the last eight years.
I double-click, and it just works.
Are you sure you downloaded the images for CD's
and not the five pieces of DVD that need to be joined before burning ?

Hp 9500 printer configuration on solaris 10 on vmware server

hi,
i installed solaris 10 on vmware server when i am going to configure the network printer 9500 hp (its having print server that also i am giving in the print server properties ) , but still i am unable to give print out from staroffice application,
can you write me steps in details Please as soon as possible,
Thanks,
Zubair.

> Please, can somebody give me the way, step by step to
configure a DNS server on solaris 10. i want to have
the directories and files that it is necessary to
modify and the modification to have a domain name
"deptech.lan" with ip adress of the DNS
server 192.168.100.2.
>
> thankDo this in this way,
1. unconfig your system
# sys-unconfig
2. Then press " Y" after that it wil reboot..
3. Then it will start config.
4. you can see like that,
Network ( y/n)
Network Interfence ( acc. 2 ur NIC , e.g. rstl0 /nge0 etc..)
select it. If you have two NIC in your system. then you choose any one..
5. Enter your " Host name"
6. then system ip
7. Then some stpes wll appear, it shows,, DHCp, Enable Ipv6 etc.. select acc. 2 ur configartion.
8. Then it will appear ' name service"
then select " Dns"
9. Give your DNS server name
10 . enter " server ip "
then search domain ( enter acc. 2 ur config/ may leave blank)
N.B: for going next stages / contiues you have to use " F2" key..
then it will configured..
Let me know if its ok or for any problem..
Thanks
Partha

Problems installation Photoshop Elements 8 on Windows 7

I tried to install Photoshop elements 8 on my Windows 7 computer, but the installation gives a failure after a certain time. A file "...cab" is not working and may be corrupt ( exact failure code I can give, if necesary). Is there any possibility to get this file or the program Photoshop Elements 8 as download file so that I can complete the installation? Thank you in advance for your answers.

Hello,
I just got the same problem already some time ago when I tried to install this programm in my computer. At that time (March 2012) the program crashed my computer, I had to reinstall all the Software completely including system software. The program I purchased in December 2011 from Amazon together with a Reflecta crystal Scan slide scanner as bundle, so I thought it will work.
I will try to install the program from the download link you gave me, in case it does not work, what can I do next without having to buy a newer version?
Regards
Franz-Josef Laven
Date: Tue, 6 Nov 2012 14:57:39 -0700
From: [email protected]
To: [email protected]
Subject: Problems installation Photoshop Elements 8 on Windows 7
Re: Problems installation Photoshop Elements 8 on Windows 7 created by Jeff A Wright in Downloading, Installing, Setting Up - View the full discussion
You can download a fresh copy of the install files by following the directions listed at http://prodesigntools.com/direct-download-links-for-lightroom-3-and-ph otoshop-elements-8.html.
I am curious did you have this installed previously or did you just purchase a copy of Photoshop Elements 8?
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/4828039#4828039
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4828039#4828039
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4828039#4828039. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Downloading, Installing, Setting Up by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

I have a problem, Installation failed

PLease help this is my problem
Installation Failed
Your installation encountered errors.
The error summary file may help you identify the issue
More troubleshooting tps:
1. Restart your computer.
2. Exit all aplications incluiding startup items, virus checking and firewall software.
3. C.ose this window and launch the installer again to reinstall your aplications
If the problems persist, please contact Customer Support for further assitance.
and the error sumary is
Exit Code: 34
-------------------------------------- Summary --------------------------------------
- 1 fatal error(s), 0 error(s), 0 warning(s)
FATAL: Payload '{0A1E2FE2-B2AD-42F4-9C74-641853FB093A} Photoshop Camera Raw 7 6.2.10.0' information not found in Media_db.

Run the Creative Suite Cleaner Tool and try again. If the issues persist, you need to provide more info - we don't even know what product you are trying to install.
Mylenium

Solaris 9/Installation in UltraSparc

Hi,
Im trying to install a Solaris 9 OS in a Sun Fire v240 machine.
First I introduced a clear SCSI HDD and the Installation DVD in the DVD PCI device. Whe I did 'boot' in the OPROM prompt it seemed 'Bad magic nuber in disk label. Cant open disk label package. Evaluating: . Cant open boot device'. When I did 'boot cdrom' it answered 'Boot device: /pci@1e600000/ide@d/cdrom 0,0 f File and args: . Boot: cannot open kernel/sparcv9/unix Enter filename [kernel/sparcv9/unix]:'
Then I formatted the HDD into a ufs format. And now when I do again 'boot cdrom' it answered me 'Boot device: /pci@1e600000/ide@d/cdrom 0,0 f File and args: . Boot: cannot open kernel/sparcv9/unix Enter filename [kernel/sparcv9/unix]:
SCSI HDD and IDE DVD are correctly connected. Installation CD Solaris 9 is original.
I even proved with a original Solaris 8 and Solaris 10 installation CD with the same results...
How can I do a correct installation of Solaris??
Thanks you!!

Q1: Am I doing the right steps?Yes, assuming you made no error writing the iso images to blank CDs. Make sure to use the "write cd from
iso image file" function in you cd writing software.
You can also try to boot from the "Software 1 of 2" CD. It's bootable, too.
Q2: Can I boot the Solaris 9 installation from the A drive, is there any way to create the boot floppy diskette(s) for it?Yes, the CD "Software 2 of 2" contains a 1.44MB boot floppy image, in file /Solaris_9/Tools/d1_image
Write the image to a formatted floppy, using the msdos "rawrite.exe" or "dd.exe" utility.

Solaris 10 - problem installation VMware

Similar Messages

Maybe you are looking for