Solaris 10 problem with network installiation

I have recently gotten about 20 new ultra 20s and all of them were configured in the same way. All of them work except for one. i have tried both adapters on the device and neither one of them can hold a connection. i have tried changing the hostname that i was assigning to it and changing the physical port that it was working on but that did not help. in the below post it looked like someone was having a similar problem.
http://forum.java.sun.com/thread.jspa?forumID=841&threadID=5080187
i checked the routing tables and they were the same as well as almost everything else in that post. is there anything similar to net-watch-all that i can try to see if the adapters are receiving traffic from the router? Also when i try to ping anything the network adapter goes down. this also occurs when i try to ping the machine with problems.

If you didn't get any messages about iprb iline value being out of range, simply run (as root):
ifconfig iprb0 plumb
Otherwise run the BIOS setup and disable plug & play os. Then run the above command.

Similar Messages

Problem with network on Iphone 4

Please tell me if someone has a problem with network on Iphone 4?

Of course other people have had problems. However, just knowing that other people have had some vague, undefined "network problems" most likely isn't going to be very useful. You'll get more and better help if you can give some details about your specific problem. Include who your carrier is, what country you're in. Then describe the exact nature of the problem. Then, maybe someone will be able to give good suggestions.
And, by the way, the free bumper program ended some time ago. It also was only a "solution" for one of many possible problems.
Best of luck.

Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution?

Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution? (No jailbreak)
Most of the time the iphone cannot reach any network and when it can, there is no data transfer, I can only make calls and sms.

Skizofrenias wrote:
Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution? (No jailbreak)
Most of the time the iphone cannot reach any network and when it can, there is no data transfer, I can only make calls and sms.
iOS: Troubleshooting Wi-Fi networks and connections
iOS: Wi-Fi or Bluetooth settings grayed out or dim

Facing problems with network due which the phone goes into hangs status

Facing problems with network due which the phone goes into hangs status. some one help me with switching between 2g and 3G network

Hi Mani Nair,
I apologize, I'm a bit unclear on the exact nature of the issue you are describing. If you are talking about having issues with a 3G cellular data network, you may find the troubleshooting steps outlined in the following article helpful:
iPhone cellular data connection issues
Regards,
- Brenden

SAP Screen Personas error "A problem with network connectivity has been detected"

Hi,
We just installed Personas release 100 SP02 and performed the
configuration steps necessary. But when we acces the url and logon to
personas we get the following erre
A problem with network connectivity has been detected.
Please check you connection and refresh your browser.
Any help to solve this issue would be appreciated.
Best Regards.

Please use this checklist to see if everything is correct:
1. restgui service handler class has CL_HTTP_EXT_ITS_BASIC
2. SPRO -> Sap screen Personas -> Maintain system has
       - 3 letter system id
       - "Server.Url" without typo and value in http(s)://<SERVER>:<PORT>/ format
       - "Service.Uri" without typo and value as /restgui
3, Note 2026487 is installed
4. If target system is different from source system then you are able to access the following
         - http(s)://<TARGETSERVER>:<PORT>/clientaccesspolicy.xml
         - http(s)://<TARGETSERVER>:<PORT>/crossdomain.xml
5. role is assigned to user under /n/persos/admin_ui -> User Maintenance -> Search -> Show user -> Role
If you still get error, then if you are using SSO, please check if you have configured login/create_sso2_ticket parameter correctly.
Thanks
Chinthan

Upgrading to 6.1.1 hasn't solved the problem with network connection on 4S. Still "No Servise"!

Upgrading to 6.1.1 hasn't solved the problem with network connection on 4S. Still "No Servise"!

Same here. Everything was fine running on ios 6.0, I don't know what possessed me to upgrade! I contacted O2 and thet went through the usual settings; reboot; airplane mode etc and it works for a while (like 5 mins) then service is losted with the network. I've even deleted the exchange email account and rebooted as read on the internet that this would fix the problem.... guest what....yep no joy! This is clearly a faulty software update and need fixing pronto! I've read that ios6.1.2 will be out soon to fix the firmware that was suppose to fix the initial network problem. When will this be realeased Apple?! It's hardly fit for purpose when I can't make calls or surf the internet.

Problem with network printer on Windows 7 machine

I'm running Mavericks on a Mac Mini. I have a Windows 7 machine with an attached Brother HL-5340D printer. I'm using the Brother HL-5340D CUPS driver. Whatever configuration I use, I cannot get my Mac to print from the Brother. I have even set up dhcp on the Mac and connected to the Windows machine with a cable. I have tried ipp, ldr/ldp, windows, ip, and most of the relevant options under advanced, and nothing works. I've run out of ideas on what to try and how to test and where to look for hints. All I get is the following:
Unable to connect to ‘192.168.33.2’ due to an error.
Not a lot of help.

James Wilde wrote:
1. I forgot to say that it was the Mac equivalent of dhcpd that I turned on so that the Mac is the server, on 192.168.33.1, and it has assigned the number 192.168.33.2 to the Windows box. And yes, I do prefer in these cases to use fixed addresses, but the Windows box seemed reluctant to accept its ip address thus the decision to start dhcpd on the Mac. After that I could not ping the Windows box from the Mac box. I didn't try to ping the Mac from the Windows box. I'll try that tomorrow. As to the network, there are only these two machines on the cable network. The default router on the Windows box is, if I remember correctly, set by dhcpd to the ip address of the house router. I have now disabled the cable network. See below.
Unusual that you could not ping Windows from the Mac. Would explain why you got a connection error with this setup. But if you have now stopped using the cable connection then this is mute.
James Wilde wrote:
2. The network profile is set to Home on the Windows box. I don't see any references to Homegroup in any of my messages on this topic. If you are referring to another post I made on a different subject, I am aware of the problems with Homegroup, and as far as I know, I have avoided this, since my wife's Windows box is the only Windows box in the house. Everything else is either Mac or Ubuntu, apart from one or two Windows virtual machines on my Mac and Ubuntu boxes.
No, you didn't mention Homegroup but you did mention not being able to see the Windows computer "Incidentally I now find that I can't get any result from selecting Windows in the Add Printer dialog." So I thought I would mention that Homegroup can cause this.
James Wilde wrote:
3. I've tried all three options in the Add printer dialog, IP, Windows, and Advanced. Under Advanced I have tried lpd and spoolss and ipp, under ip I have tried ipp and lpd. The share name is Brother-HL-5340D, and the hyphen between Brother and HL I put there myself to make it one 'word'.
I've just tried your suggestion and get the following when I click on Add.
Unable to verify the printer on your network.
Unable to connect to ‘192.168.1.202’ due to an error. Would you still like to create the printer?
I've seen this occur when the LPD process is not working. Open the Services pane on the PC and check the LPD service has started. If it is running and you still get the error message, what happens if you say yes to creating the printer?
James Wilde wrote:
As i said, I have disabled the cable network and am using the house wifi network (all machines with fixed IPs). I can ping the computer and have just mounted a disk on her computer with smb using Finder/Go. The mount does appear to be read only, but at least I can open all the folders.
Anything else I can try?
That is a good outcome. Proves there is a functional path between both computers.
Since you can connect using SMB, and if you cannot LPD to work, then try adding the printer again using the Windows view in the Add printer pane. You should see the workgroup used by the Win7 PC followed by the Win7 computer name. Selecting it should prompt you to authenticate (unless you have saved the account in Keychain) and then the printer share name should appear. After selecting the share, select the Generic PS driver as a test to see if you can submit a print job - open the print queue on the Win7 PC to see if the print job appears. If this does work, you can remove the printer on the Mac and add again, this time selecting the Brother driver and then see if this works.

Adobe reader XI: doule sided print problem with network printer (windows 8 pro)

Hi, I'm facing a problem with my old printer, the xerox phaser 3160n. It was connected to my notebook through network connection, and everything works well with Adobe X /Win 7 OS (including the double side print, of course) last month, I have upgraded my NB to windows 8 with clean install
clean install my printer driver for windows 8 too, and Adobe reader XI was also downloaded through official website.
However, since I was about to use double sided print in Adobe reader XI (11.00.02) it couldn't obey the order, but just print one side as usual
I have checked the "option" of my printer, and it was correctly set to "double-sided print". I have tried word 2013 to open the same pdf, and choose the same "double-sided print" and it works perfectly.
Is this problem a bug? and would it be corrected in the next update version??
(I remeber I've saw a similar issue too, with network printer, but I couldn't find it)
Thanks!!!

Hi,
Meanwhile, after insatlling the latest driver for printer from the manufacture website, restart the spooler service as a test.
Start > Run > cmd and type "net stop spooler" after that "net start spooler" or start > run > service.msc and restart it over the GUI.
Run Printer Troubleshootor under Action Center\Troubleshooting\Programs\Printer, and check if it helps.
And yes, the manufacture should have more sence about the printer, it's recommended to contact them.
Yolanda Zhu
TechNet Community Support

Windows 8/8.1 Partial Print Problems with Networked Inkjet Printers (Envy, Officejet and Deskjet)

There are a lot of threads being posted about this problems with printing on the following these devices when they are connected in a Network Environment (Wireless or Wired)
HP Officejet Pro 6830
HP Officejet 6800
HP Officejet Pro 6230
HP Officejet 6220
HP Officejet Pro 8610 e-All-in-One Printer series
HP Officejet Pro 8620 e-All-in-One Printer series
HP Officejet Pro 8630 e-All-in-One Printer series
HP Officejet Pro 8640 e-All-in-One
HP Officejet Pro 8650 e-All-in-One
HP Officejet Pro 8660 e-All-in-One
HP Officejet 7610 Wide Format ePrinter
HP Officejet Pro 3610 Black and White e-All-in-One
HP Officejet Pro 3620 Black and White e-All-in-One
HP Officejet Pro 251dw Printer series
HP Officejet Pro 276dw MFP series
HP Officejet 7110 Wide format ePrinter
HP Officejet Pro 501dw Printer
HP Officejet Pro 401dw Printer
HP Officejet Pro X451dw Printer
HP Officejet Pro X576dw MFP
HP Officejet Pro X476dn MFP
HP Officejet Pro 451dn/551dn MFP
HP Officejet Pro 451dw/551dw MFP
HP Officejet 4630 e-All-in-One
HP Deskjet Ink Advantage 4640 e-All-in-One Printer series
HP Deskjet 2540 All-in-One Printer
HP Deskjet Ink Advantage 2540 All-in-One Printer
HP ENVY 5530 e-All-in-One Printer
HP Deskjet Ink Advantage 4510 e-All-in-One Printer
HP ENVY 4500 e-All-in-One Printer
HP Deskjet Ink Advantage 3540 e-All-in-One Printer
HP posted a workaround for this problem while they were working with Microsoft to get the root cause of the problem, many customers commented that the workaround helped them out and they were able to print. This workaround was not easy to use as the customer needed to add another printer manually and changed drivers.
We can now announce that the problem has been fixed, the problem involved a Microsoft Network component that HP was using to talk to and track the printers on the network. This fix is being rolled out by Microsoft via Windows Update and anyone who has Windows Update enabled and set to automatically install updates should have already received this update. For those that do not have Windows Update setup to automatically install fixes the fix is available now and should be installed.
The details of this fix and a manual method of installing it can be found here.
http://support.microsoft.com/kb/3000461
This fix is only designed for users that are using there printer on a Network (Wireless or Wired) and will not fix partial printing problems encountered with USB connections.
There are many threads in HPs forums about this issue (below are links to a few of them)
http://h30434.www3.hp.com/t5/Printing-Issues-Troubleshooting/Missing-partial-prints-amp-Printer-Offl...
http://h30434.www3.hp.com/t5/Printing-Issues-Troubleshooting/HP-Envy-4500-cancels-job-in-the-middle-...
http://h30434.www3.hp.com/t5/Other-Printing-Questions/Only-prints-half-a-page/m-p/4054888
JonW
I work for HP

@tenkeypro
First, I would suggest you uninstall the exsisting driver and reinstall following one of these documents to see if it will clear this error message:
Install HP print and scan software on a Windows 8 computer (32-bit and 64-bit)
Universal Print Driver (no scan)
Driver support included in Windows 8 / Windows 8.1 or in Windows Update
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Having Problem With Network

Hi,
I'm having problem with a carrier network (Maxis),which i always get 'no service',whether i on the phone and after i off the phone.I try to reset the network,but it seems the same.Please help me solve my problems.

did u have this problem before of after the last update.

[Solved] Problem with network

Oi,
I have a problem with setting up my network configuration, when I run /etc/rc.d/network start I get the following SIOCADDRT: Network is unreachable. I have a Realteck RTC 8168/8111 and load the following modules: 8139too, 8139cp and r8169.
/etc/rc.conf
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(lo eth0)
ROUTES=(!gateway)
ifconfig
lo
Link encap: Local Loopback
inet addr: 127.0.0.1 Mask:225.0.0.0
enz..
ifconfig eth0
Link encap:UNSPEC HWaddr 00-DC-10-00-F4-B3-EC-00-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:1500 Metric:1
enz...
When I make an extra divice eth1. ifconfig eth1
eth1: error fetching interface information: Decice not found
I have a Fireware port on my computer. I blocked eth1394, ohci1394 and ieee1394 from loading. Now when i run ifconfig eth0 I get:
eth0: error fetching interface information: Decice not found
It looks like there is something strange with the fireware port and eth0, can someone help me?
<_abe>

It seems to me that this is a driver problem.
Just to get out of doubts do this:
1. type ifconfig eth0 192.168.1.30
2. type route add default gw 192.168.1.1, eth0
3. echo "nameserver xx.xxx.xxx.xxx" > /etc/resolv.conf
IMPORTNAT: The above assumes you are using a LAN with a private address of 192.168.1.x
You should adjust these numbers accordingly based on your LAN settings.
In step 3 the nameserver is the address of one of your nameservers.
This will set up your card with a static address. If this works then dhcp is not working on your network.
Also if this works ifconfig will give you a totally different response than what you currently get.
Finally step 2 is the green address of your router, so you can connect to the internet.
Hope this helps.
R

Windows 10 for phones emulators on Windows 10 10041 - problem with network connection

Hi,
I can't connect to Internet on Windows 10 mobile emulators on Windows 10041. I have tried to resolve problem. First I noticed, there was problem with displaying properties main network connection. I had reinstalled network driver. After that I reinstalled
Hyper-V on Windows and recreated virtual machines for mobile emulators. Nothing helps.
On the same machine Windows Phone 8.1 emulator on Windows 8 has access to Internet.
I don't know if there was issue which is discribed
http://blogs.msdn.com/b/wsdevsol/archive/2013/10/01/why-can-t-the-windows-phone-emulator-go-online.aspx, becuse the same configuration I have on Windiows 8.1 and Windows 10 and on Windows 8.1 I have access and on Windows 10 I haven't.
Martin

I just disabled bluetooth connection in Network Connections panel and I have access to Internet in Windows 10 emulator!

Permissions problems with networked users

Hi,
We use 11 intel imacs with networked users from an xserve and run Logic Pro. I have told all students to run their projects from a temporary folder on the local hard drive and then copy the final work to their desktop to secure it for next time if they use a different machine, this seems to work OKish.
However there are a few features that refuse to work in Logic for a managed user, time stretching is one and various others so what I need to know is anyone have a comprehensive list of ALL the folders that logic would use so I can make them all read/write to everyone and see if the problems go away. A local account with admin privileges seems to work fine but I am keen to solve the problem at the root level and this seems like a good place to start.
Anyone have any tips on networked LDAP users and Logic Pro?

I don't know about the network stuff as such, but there are various utilities that hook into OSX to display all file activity - you can turn on logging, run the application, then look through the log to see what files that Logic was trying to access while it was running.
It might give you some clues, beyond all the obvious stuff (application, preferences files, app support files, garageband libraries, plugin settings, plugins, sampler instruments, audio files, project manager database files and so on)

HT1976 Y have the problem with network 5.1.1 ...no services ??

Hello my name is costel end y have an iphone 4 ios 5.1.1 factory unlock end the last night appear on display "no service" end searching.... But nothing, what is hapening? Y make restore end nothing she dont work...please y want help

It seems that there is an issue with IOS 5.1.1
1) Charlie3012
Re: Updated to ios 5.1.1 and had no service since for least 6 hours now.
I had the same problem, the network provider had an issue with their network but after that was fixed, I still got the message "no service". I have an iPhone 4, no jailbreak, everything standard. What solved the problem for whatever reason was to remove the sim card and put it back in.
2) As suggested on another thread:
FarID0
Re: Updated to ios 5.1.1 and had no service since for least 6 hours now.
hey, he is alive!
i've turned on reseted iphone, waited 10 minutes, pulled out sim card, iphone says "no sim card" and pulled sim in, waited search stage and vuola!
Hope it will help
3) Go to your carriers' shop and change your SIM card.

Problem with Network Install

Hi there,
I am trying to install Solaris 9 from network to a Netra X1 server. I created an intall server on another Sun Sparc server, and added the Netra X1 as an install client. I sucessfully lunched the intallation process by "net boot". But, after I answered all the questions on the screen and started either upgrade or install, the installation process terminated with the error message "cannot read media from cdrom". It seems to me that I have the network connection already, the installation process knows where the image is. But, I cannot figure out why the installation process terminated. I would appreciate very much if anyone could give me a help.

If you did not create an image on your jumpstart server then it assumes you are installing from the CDROM on the other Sun system. See InfoDoc 27794 (Solaris 8 Jumpstart Guide). This procedure is the same for what you want to do. Process 1 is Jumpstarting from remote CDROM and Process 2 is installing from image loaded on your server. See: http://sunsolve.Sun.COM/pub-cgi/retrieve.pl?doc=finfodoc%2F27794&zone_32=27794

Solaris 10 problem with network installiation

Similar Messages

Maybe you are looking for