Solaris 10 v440 install failure.

Hi,
Have a v440 which passes full diag routine. with brand new solaris 10 dvd received from sun, with a freshly formatted 9gb hdd.
When trying to bbot from the dvd, "boot cdrom", i get the following cycling through.
Hardware watchdog enabled
svc.configd: smf(5) database integrity check of:
/etc/svc/repository.db
failed. The database might be damaged or a media error might have
prevented it from being verified. Additional information useful to
your service provider is in:
/etc/svc/volatile/db_errors
The system will not be able to boot until you have restored a working
database. svc.startd(1M) will provide a sulogin(1M) prompt for recovery
purposes. The command:
/lib/svc/bin/restore_repository
can be run to restore a backup version of your repository. See
http://sun.com/msg/SMF-8000-MY for more information.
Requesting System Maintenance Mode
(See /lib/svc/share/README for more information.)
svc.configd exited with status 102 (database initialization failure)
svc.startd: Could not exec() sulogin: No such file or directory.
i have tried other dvd rom drives and other installtion media but am getting nowwhere.
Am newbie to solaris, Can anyone HELP!
Many Thanks.

many thanks those that looked, eventually found an obscure notice about date and time, corrected these and all is well.
Cheers

Similar Messages

Netra t1 105: Solaris 8 & 9 install failures

Hi Everyone,
I have two (2) Sun Netra T1 105 machines, each with a single 360MHz Ultra SPARC IIi and 256MB RAM. Both have 18.2GB drives that have been wiped clean.
I am connecting using Winblows 2000 and Hyperterminal, serial port B, 9600,8,n,1.
I want to install a fresh copy of Solaris 9 on these systems, but I am having absolutely no luck. I boot from the Solaris 9 install CD and the systems just hang. I've also tried to do network installs, and they hang as well.
I thought it might be my Solaris 9 install media, so I tried to install Solaris 8 using several different releases - 4/01, 10/01 & 2/02. Each time, I get the same result - the boxes just hang.
I make it this far (serial, MAC, and hostid x'ed out to keep our security folks happy):
Netra t1 (UltraSPARC-IIi 360MHz), No Keyboard
OpenBoot 3.10.25 ME, 256 MB memory installed, Serial #XXXXXXXX.
Ethernet address 8:0:20:XX:XX:XX, Host ID: XXXXXXXX.
ok boot cdrom
Boot device: /pci@1f,0/pci@1/pci@1/ide@e/cdrom@2:f File and args:
SunOS Release 5.9 Version Generic 64-bit
Copyright 1983-2002 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
And then it hangs forever. In the OBP, I've set the input and output ttys to ttyb to eliminate LOM interference.
Here is a snapshot of the printenv output:
ok printenv
Variable Name Value Default Value
tpe-link-test? true true
scsi-initiator-id 7 7
keyboard-click? false false
keymap
watchdog-timeout 65535 65535
watchdog-enable? false false
ttyb-rts-dtr-off false false
ttyb-ignore-cd false true
ttya-rts-dtr-off false false
ttya-ignore-cd false true
ttyb-mode 9600,8,n,1,- 9600,8,n,1,-
ttya-mode 9600,8,n,1,- 9600,8,n,1,-
cpci-probe-list 0,1,2,3,4,5,6,7,8,9,a,b, ... 0,1,2,3,4,5,6,7,8,9,a,b, ..
pcia-probe-list 1 1
pcib-probe-list 1,2,3 1,2,3
mfg-mode off off
diag-level min max
d7s-flipped? false false
#power-cycles 67
system-board-serial#
system-board-date
last-poweroff-cause 0 0
env-monitor disabled enabled
shutdown-temperature 74 72
warning-temperature 69 67
fcode-debug? false false
output-device ttyb ttya
input-device ttyb ttya
load-base 16384 16384
auto-boot-retry? false false
use-boot-table? false false
boot-command boot boot
auto-boot? false true
watchdog-reboot? false false
diag-file
diag-device net net
boot-file
boot-device disk net disk net
local-mac-address? true false
net-timeout 0 0
ansi-terminal? true true
screen-#columns 80 80
screen-#rows 34 34
silent-mode? false false
use-nvramrc? false false
nvramrc
security-mode none
security-password
security-#badlogins 21
oem-logo
oem-logo? false false
oem-banner
oem-banner? false false
hardware-revision
last-hardware-update
diag-switch? false false
I have the feeling I am missing something very simple, but I am at a loss. Any assistance is greatly appreciated!
Chad E. Carlson
Skandia Technology Center, Inc.
Shelton, CT USA

This could be part of the problem. How exactly did you wipe the disks in the other machine, and what type of machine was it?I installed the disks into a Sun Netra T1125, partioned (using format) and newfs'd them to create basic file systems.
How about a "boot cdrom -s"? If it boots this way, does "format" see the disks ok?Tried this, same result. The systems don't make it past the licensing terms message.
As for the mini tests - I ran them against every device, and everything seems OK. The floppy test threw an error because I didn't have a floppy drive installed.
I have a 4 port QFE card installed in the machine - all of the loopback tests passed, but the transceiver tests failed. None of the ports are connected (no cables). The two built in Ethernet ports also passed loopback, and 1 passed the transceiver test (the other failed) - the transceiver that passed has a network cable installed.
Testing /pci@1f,0/pci@1/pci@1/pci@f/SUNW,qfe@3,1
Internal loopback test -- succeeded.
Transceiver check -- failed
Selftest failed. Return code = -1
Testing /pci@1f,0/pci@1/pci@1/pci@f/SUNW,qfe@2,1
Internal loopback test -- succeeded.
Transceiver check -- failed
Selftest failed. Return code = -1
Testing /pci@1f,0/pci@1/pci@1/pci@f/SUNW,qfe@1,1
Internal loopback test -- succeeded.
Internal loopback test -- succeeded.
Transceiver check -- failed
Selftest failed. Return code = -1
Testing /pci@1f,0/pci@1/pci@1/pci@f/SUNW,qfe@0,1
Internal loopback test -- succeeded.
Transceiver check -- failed
Selftest failed. Return code = -1
Testing /pci@1f,0/pci@1,1/network@3,1
Internal loopback test -- succeeded.
Transceiver check -- failed
Selftest failed. Return code = -1
Testing /pci@1f,0/pci@1,1/scsi@2
Testing /pci@1f,0/pci@1,1/network@1,1
Internal loopback test -- succeeded.
Transceiver check -- passed
Could I be experiencing problems because of the QFE card?? Doesn't seem logical, but.... perhaps I will yank it out and try again....

Remote Install Failure on AIA3.0

Hi,
Remote Install Failure on AIA 3.0:
AIA 3.0 installations on Windows XP-Pro is failing in Step 4 of 11 with the Error
"Node manager is down or the username and password entered is incorrect"
Details on the installation are as follows:
1) Installation is done on a Windows-XP 32 bit SP2, RAM - 4 GB.
2) SOA Suite 11gR1 PS1 and Weblogic 10.3.2 successfully installed.
3) SOA managed server, Admin server and node manager are running successfully on remote server.
4) The status of Node manager is reachable and has been confirmed through the admin console.
5) When installing AIA 3.0 use Remote Install option, the 4th step is failing after providing the node manager credentials of remote server.
Error message is "Node manager is down or the username and password entered is incorrect".
6) We given remote server configuration on 4th step (Host Name, Admin Port, Domain name, user/pass).
7) The Remote WLS Server is reachable.
8) Installer is always looking local node manager is not looking for Remote node manager which one is running on remote machine.
Error Log
Adding C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM for deletion.
Adding to classpath:file:/C:/WINNT/TEMP/OraInstall2010-04-29_04-25-49PM/ext/jlib/soawl.jar
Adding to classpath:file:/C:/WINNT/TEMP/OraInstall2010-04-29_04-25-49PM/ext/jlib/template.jar
null
configFileName:C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\footprint.xml
osName:Windows XP
Inside startPreReqOperation...prereq
osName:Windows XP
diskSpaceRequirements from engine:Home id =SoftwareOnlyOraclehome name=Oracle home variable=%AIA_HOME_PATH% fixedSpace=2048 unit=MB condition=null totalSpaceRequired=0 isConditionSatisfiedfalse
entryPoint: entryPoint = oracle.installType.all condition = null className = null
contextFile:C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\prereq\oui\agent_prereq_context.xml
The entry point is: oracle.installType.all
Check Name:CertifiedVersions
Check Description:This is a prerequisite condition to test whether the Oracle software is certified on the current O/S or not.
Expected result: One of 5.1,5.2,6.0,6.1
Actual Result: 5.1
Check complete. The overall result of this check is: Passed
Check Name:ServicePackChecks
Check Description:This is a prerequisite condition to test whether the Service Pack level recommended for installing the product is available on the system.
Expected result: 2
Actual Result: 2
Check complete. The overall result of this check is: Passed
Check Name:TotalMemory
Check Description:This is a prerequisite condition to test whether the system has sufficient physical memory.
Expected result: 1024MB
Actual Result: 3191MB
Check complete. The overall result of this check is: Passed
Property File location: D:\AIA3.1\New Folder\cd\Disk1\install\win32\aiaoneclick.properties
Item State: javax.swing.JComboBox[,170,52,262x18,invalid,layout=com.jgoodies.looks.plastic.PlasticComboBoxUI$PlasticComboBoxLayoutManager,alignmentX=0.0,alignmentY=0.0,border=,flags=4194632,maximumSize=,minimumSize=,preferredSize=,isEditable=true,lightWeightPopupEnabled=true,maximumRowCount=8,selectedItemReminder=AIA3]
Path: D:\Oracle11GPS\Oracle\Middleware_new\AIA3
Item State: javax.swing.JComboBox[,170,81,262x18,invalid,layout=com.jgoodies.looks.plastic.PlasticComboBoxUI$PlasticComboBoxLayoutManager,alignmentX=0.0,alignmentY=0.0,border=,flags=4194632,maximumSize=,minimumSize=,preferredSize=,isEditable=true,lightWeightPopupEnabled=true,maximumRowCount=8,selectedItemReminder=D:\Oracle11GPS\Oracle\Middleware_new\AIA3]
Home: AIA3
In processFieldStringAIA Home
In processFieldStringJAVA HOME
In processFieldStringAIA Home Path
In processFieldStringAIA Instance Name Contains invalid characters
getting root directory
D:\oracle11GPS\Middleware\user_projects\domains\dev_domain
truevalue for type of install
D:\Oracle11GPS\Oracle\Middleware_new\jdeveloper
D:\Oracle11GPS\Oracle\Middleware_new
*****Web Logic Home: D:\Oracle11GPS\Oracle\Middleware_new\wlserver_10.3
CLASSPATH: D:\Oracle11GPS\Oracle\Middleware_new\wlserver_10.3\server\lib\weblogic.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM;;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\adapters.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\adf-config.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\aqapi.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\bpelImport.log;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\ccrQueries.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\com.bea.cie.comdev_6.1.0.0.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\com.bea.cie.config_6.0.0.0.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\com.bea.core.common.security.api_1.0.0.0_5-1-0-0.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\com.bea.core.nodemanager.plugin_1.3.0.0.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\commonutils.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\connections.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\dms.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\emocmutl.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\encrypt.bat;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\encrypt.sh;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\engine.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\enginehelp.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\footprint.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\glassfish.jaxb.xjc_1.0.0.0_2-1-7.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\glassfish.jaxb_1.0.0.0_2-1-7.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\harvest-tasks.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\harvest.bat;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\harvest.sh;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\harvester-10.3.1.0.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\harvester-ant.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\harvesterSettings.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\install.properties;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\jython-modules.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\log-config.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\log4fl.properties;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\message.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\ojdbc5.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\ojdl-log4j.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\ojdl.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\ojdl2.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\oneclick.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\oneofftool.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\runant.bat;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\runant.sh;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\setenv.bat;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\setenv.sh;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\soainstallhelp.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\soawl.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\SysInfo.dll;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\template.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\tools.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\tools11g.xml;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\types.properties;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\wlcipher.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\wlfullclient.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\wtinstallhelp.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\xml.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\ext\jlib\xmlparserv2.jar;;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\OraInstaller.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\oneclick.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\xmlparserv2.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\share.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\OraInstallerNet.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\emocmutl.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\emCfg.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\OraPrereq.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\jsch.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\ssh.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\remoteinterfaces.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\http_client.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\OPatch\jlib\opatch.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\OPatch\jlib\opatchactions.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\OPatch\jlib\opatchprereq.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\OPatch\jlib\opatchutil.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstImages.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_de.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_es.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_fr.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_it.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_ja.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_ko.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_pt_BR.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_zh_CN.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\InstHelp_zh_TW.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\oracle_ice.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\help4.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\help4-nls.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\ewt3.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\ewt3-swingaccess.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\ewt3-nls.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\swingaccess.jar;\;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\jewt4.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\jewt4-nls.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\orai18n-collation.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\orai18n-mapping.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\ojmisc.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\xml.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\srvm.jar;C:\WINNT\TEMP\OraInstall2010-04-29_04-25-49PM\oui\jlib\classes12.jar
1
localhost
LocalMachine
Connecting to Node Manager ...
<Apr 29, 2010 4:31:11 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
Either the password and username entered are incorrect or the node manager is down
Traceback (innermost last):
File "<string>", line 1, in ?
File "<iostream>", line 123, in nmConnect
File "<iostream>", line 618, in raiseWLSTException
WLSTException: Error occured while performing nmConnect : Cannot connect to Node Manager. : I/O error while reading domain directory
Use dumpStack() to view the full stacktrace
Anyone knows how to install AIA Remote Install on the remote SOA server?

Hi,
may be you enter the wrong username or password? Or there is a problem with certificate? The look file describe a wrong user name or password or nm is not reachable. Is it possible to start managed server via Admin Console? Please check nm log files.
Regards,
Marcel

How to change number of retries and delay before retrying after software install failure

I deploy a software to client, but the installation is fail, so it will retry. but How to change the number of retries and delay before retrying after software install failure?
I find "Retry Settings" in "Software Distribution Component Properties". But I think it work for Distribution, not the installation. am I right?

First, are you referring to packages or applications because the behavior is different.
Also, why do you want it to retry a failure? It failed for a reason so you need to fix the cause of the failure first. If it failed the first, it will likely fail the next time for the same reason. In general, ConfigMgr will only retry on transient type
errors.
Jason | http://blog.configmgrftw.com

Photoshop Elements 10 Mac Ongoing Install Failure - Exit Code 7

Photoshop Elements 10 Mac Ongoing Install Failure - Exit Code 7
I downloaded Photoshop Elements 10 for Mac (not trial, with valid serial #)
Mac OSX 10.7.2, 3.6 GHz Intel Core i5, 16 GB RAM
I know the install package is valid because I installed it on my backup laptop (same Max OSX version) after I was having problems with my primary desktop and it installed fine. I have followed all the instructions on the install package including "restarting my system and installing again," and the install keeps failing with the same message:
Exit Code: 7
-------------------------------------- Summary --------------------------------------
- 0 fatal error(s), 18 error(s), 3 warning(s)
WARNING: DS013: Payload {298CF0B0-8B47-46DF-B726-8E4BFAD5432E} AdobeHelp 1.0.0.0 is already installed and the session payload {EB3A47AA-B4E2-4857-A69C-92A6E097F24C} AdobeHelp 3.5.0.0 has no upgrade/conflict relationship with it.
WARNING: DS013: Payload {75063C76-E858-455B-9C26-89E55D26F276} AdobeHelp 3.2.0.0 is already installed and the session payload {EB3A47AA-B4E2-4857-A69C-92A6E097F24C} AdobeHelp 3.5.0.0 has no upgrade/conflict relationship with it.
ERROR: DS013: Verifying payload integrity : Failed with code 1
----------- Payload: {60CB5C6D-5B99-45D3-BAB5-E7728182101E} Adobe Photoshop Elements 10 10.0.0.0 -----------
ERROR: DF024: Unable to preserve original file at "/Library/Fonts/BickhamScriptPro-Regular.otf" Error 0(Seq 1519)
ERROR: DW063: Command ARKDeleteFileCommand failed.(Seq 1519)
ERROR: DF023: Unable to delete file "/Applications/Adobe Photoshop Elements 10/Support Files/Adobe Photoshop Elements Editor.app/Contents/Info.plist". Error 0(Seq 2)
ERROR: DW063: Error rolling back command ARKCopyFileCommand(Seq 2)
ERROR: DF001: Unable to get permissions of "/Applications/Adobe Photoshop Elements 10/Support Files/Adobe Photoshop Elements Editor.app/Contents"(Seq 2)
ERROR: DW063: Error rolling back command ARKCreateDirectoryCommand(Seq 2)
ERROR: DF001: Unable to get permissions of "/Applications/Adobe Photoshop Elements 10/Support Files/Adobe Photoshop Elements Editor.app"(Seq 2)
ERROR: DW063: Error rolling back command ARKCreateDirectoryCommand(Seq 2)
ERROR: DF001: Unable to get permissions of "/Applications/Adobe Photoshop Elements 10/Support Files"(Seq 2)
ERROR: DW063: Error rolling back command ARKCreateDirectoryCommand(Seq 2)
ERROR: DF015: Unable to delete symlink "/Applications/Adobe Photoshop Elements 10/Adobe Photoshop Elements 10"(Seq 1)
ERROR: DW063: Error rolling back command ARKCopySymlinkCommand(Seq 1)
ERROR: DF001: Unable to get permissions of "/Applications/Adobe Photoshop Elements 10"(Seq 1)
ERROR: DW063: Error rolling back command ARKCreateDirectoryCommand(Seq 1)
WARNING: DW036: Payload cannot be installed due to dependent operation failure
ERROR: DW050: The following payload errors were found during install:
ERROR: DW050: - Adobe Photoshop Elements 10: Failed due to Language Pack installation failure
ERROR: DW050: - Adobe Photoshop Elements 10_AdobePhotoshopElements10_en_US: Install failed
Suggestions? thanks.

Issue resolved with the help of Adobe Support (Mercer). My problem had been seen in another machine, there were empty folders in the Fonts Folder (Hard Drive>Library>Fonts) that the installer could not reconcile or delete, that was hanging up the Installer.
My fix was to delete the following empty folders from the Fonts Folder:
AdobeMingStd-Light.otf
BickhamScriptPro-Regular.otf
KozMinPro-Regular.otf
MyriadPro-BoldCond.otf
TektonPro-BoldCond.otf
And then re-run the installer (be sure to empty the trash).
My advice would be to first read the installer log and look for names of font folders that could not be resolved, then dump those. Another way would be to dump any empty folders in the Fonts Folder, empty the trash, then re-sun the installer.

Problems making Solaris 10 install disk for x86

I have an Ultra 40 M2. I made a boot/install DVD disk with Solaris 10 for x86.
The system just doesn't recognize it at all, like there is nothing in the DVD drive.
What am I doing wrong?
The DVD drive does recognize other DVDs, just not the Solaris 10 install one (I created two install disks to no avail)

How are you burning the DVD. What software/options.
Theres a howto here
http://www.sun.com/software/solaris/self_help.jsp#burning

Solaris 10 instalation in Guest Domain - Timed out waiting for TFTP reply

I have the next trouble
I have a Sun Fire T1000 and i want install two Guest LDOM's with Solaris10 in each one, I Install the LDOM Manager 1.0.3 and the service is "online" also the another services needed
First Setup the 2 Guest LDOM's in the primary Domain sucesfully .... here is a desc of the configuration.
# ldm list-bindings
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
primary active -n-cv SP 4 1G 0.1% 2h 14m
MAC
00:14:4f:a7:85:1e
VCPU
VID PID UTIL STRAND
0 0 0.2% 100%
1 1 0.2% 100%
2 2 0.1% 100%
3 3 0.1% 100%
MAU
ID CPUSET
0 (0, 1, 2, 3)
MEMORY
RA PA SIZE
0x8000000 0x8000000 1G
VARIABLES
diag-switch?=true
security-#badlogins=0
IO
DEVICE PSEUDONYM OPTIONS
pci@780 bus_a
pci@7c0 bus_b
VCC
NAME PORT-RANGE
primary-vcc0 5000-5100
CLIENT PORT
aplica_srss1@primary-vcc0 5001
aplica_prod@primary-vcc0 5000
VSW
NAME MAC NET-DEV DEVICE MODE
primary-vsw0 00:14:4f:a7:85:1e bge0 switch@0
PEER MAC
vnet2@aplica_srss1 00:14:4f:fb:f4:e0
vnet1@aplica_prod 00:14:4f:fb:2c:60
VDS
NAME VOLUME OPTIONS DEVICE
primary-vds0 vol1 /dev/dsk/c0t0d0s3
CLIENT VOLUME
vdisk1@aplica_prod vol1
VCONS
NAME SERVICE PORT
SP
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
aplica_prod active -t--- 5000 4 2G 15% 9m
MAC
00:14:4f:fb:2c:60
VCPU
VID PID UTIL STRAND
0 4 35% 100%
1 5 0.0% 100%
2 6 7.0% 100%
3 7 84% 100%
MEMORY
RA PA SIZE
0x8000000 0x48000000 2G
VARIABLES
auto-boot?=true
boot-device=
use-nvramrc?=true
NETWORK
NAME SERVICE DEVICE MAC
vnet1 primary-vsw0@primary network@0 00:14:4f:fb:2c:60
PEER MAC
primary-vsw0@primary 00:14:4f:a7:85:1e
vnet2@aplica_srss1 00:14:4f:fb:f4:e0
DISK
NAME VOLUME TOUT DEVICE SERVER
vdisk1 vol1@primary-vds0 disk@0 primary
VCONS
NAME SERVICE PORT
aplica_prod primary-vcc0@primary 5000
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
aplica_srss1 bound ----- 5001 24 13184M
MAC
00:14:4f:fb:ad:fb
VCPU
VID PID UTIL STRAND
0 8 100%
1 9 100%
2 10 100%
3 11 100%
4 12 100%
5 13 100%
6 14 100%
7 15 100%
8 16 100%
9 17 100%
10 18 100%
11 19 100%
12 20 100%
13 21 100%
14 22 100%
15 23 100%
16 24 100%
17 25 100%
18 26 100%
19 27 100%
20 28 100%
21 29 100%
22 30 100%
23 31 100%
MEMORY
RA PA SIZE
0x8000000 0xc8000000 13184M
VARIABLES
auto-boot?=true
boot-device=
NETWORK
NAME SERVICE DEVICE MAC
vnet2 primary-vsw0@primary network@0 00:14:4f:fb:f4:e0
PEER MAC
primary-vsw0@primary 00:14:4f:a7:85:1e
vnet1@aplica_prod 00:14:4f:fb:2c:60
VCONS
NAME SERVICE PORT
aplica_srss1 primary-vcc0@primary 5001
Then i mount the ISO images of The solaris OS 5/08, Later install the jumpstart server without troubles.... Here are the Configuration files needed for the properly setup of the service for a better guide

# ./add_install_client -d -e 0:14:4f:fb:2c:60 -s Zolder:/var/jump_start/ sun4v
cleaning up preexisting install client "0:14:4f:fb:2c:60"
To disable 0:14:4f:fb:2c:60 in the DHCP server,
remove the entry with Client ID 0100144FFB2C60
To enable 0100144FFB2C60 in the DHCP server, ensure that
the following Sun vendor-specific options are defined
(SinstNM, SinstIP4, SinstPTH, SrootNM, SrootIP4,
SrootPTH, and optionally SbootURI, SjumpCF and SsysidCF),
and add a macro to the server named 0100144FFB2C60,
containing the following option values:
Install server (SinstNM) : Zolder
Install server IP (SinstIP4) : 172.24.0.10
Install server path (SinstPTH) : /var/jump_start/
Root server name (SrootNM) : Zolder
Root server IP (SrootIP4) : 172.24.0.10
Root server path (SrootPTH) : /mnt/s0/Solaris_10/Tools/Boot
Boot file (BootFile) : 0100144FFB2C60
# cat /etc/inet/hosts // The Content of this file is exactly with ipnodes file
127.0.0.1 localhost
172.24.0.10 Zolder loghost
172.24.0.9 primary-vsw0
172.24.0.8 aplica_prod
172.24.0.7 aplica_srss1
# cat /etc/ethers
00:14:4f:fb:2c:60 aplica_prod
# cat /etc/bootparams
aplica_prod root=Zolder:/mnt/s0/Solaris_10/Tools/Boot install=Zolder:/var/jump_start/ boottype=:in rootopts=:rsize=8192
# cat /etc/dfs/dfstab
share -F nfs -o ro,anon=0 /var/jump_start/
share -F nfs -o ro,anon=0 /mnt/s0/Solaris_10/Tools/Boot
share -F nfs -o ro,anon=0 /mnt/s1
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
vsw0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.24.0.10 netmask fffffe00 broadcast 172.24.1.255
ether 0:14:4f:a7:85:1e
vsw0:1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.24.0.9 netmask fffffe00 broadcast 172.24.1.255
Here i plumb up the networks interfaces and setup the vsw0 device and change the MAC address of the vsw0 for the same of the bge0 device.
Then i Log to a Guest LDOM aplica_prod
----------START CONSOLE 1-------------------------------
# telnet localhost 5000
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
Connecting to console "aplica_prod" in group "aplica_prod" ....
Press ~? for control options ..
----END CONSOLE 1----
At the same time i open another console for startup the Guest LDOM aplica_prod i make a snoop of the vsw0 interface
---START CONSOLE 2---
# ldm start aplica_prod
LDom aplica_prod started
-bash-3.00# snoop -d vsw0 | grep aplica_prod
Using device /dev/vsw0 (promiscuous mode)
---END CONSOLE 2-----
In the other console is produced the next exit
----START CONSOLE 1------
Sun Fire(TM) T1000, No Keyboard
Copyright 2008 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.28.9, 2048 MB memory available, Serial #66792544.
Ethernet address 0:14:4f:fb:2c:60, Host ID: 83fb2c60.
Boot device: File and args:
ERROR: boot-read fail
Evaluating:
Can't locate boot device
{0} ok boot vnet1 install
Boot device: /virtual-devices@100/channel-devices@200/network@0 File and args: install
Requesting Internet Address for 0:14:4f:fa:82:17
Requesting Internet Address for 0:14:4f:fa:82:17
Timed out waiting for TFTP reply
---END CONSOLE 1-----
in the console 2 the snoop generates an exit of the net traffic for the vsw0 device
----START CONSOLE 2--------
primary-vsw0 -> aplica_prod RARP R 0:14:4f:fb:2c:60 is 172.24.0.8, aplica_prod
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
primary-vsw0 -> aplica_prod RARP R 0:14:4f:fb:2c:60 is 172.24.0.8, aplica_prod
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
----END CONSOLE 2----
Once start the snoop to produce messages make a ping to the IP's that should be assigned in the host file and all give a succesful answer BUT without start the Solaris 10 Instalation
# ping 172.24.0.8
172.24.0.8 is alive
# ping 172.24.0.9
172.24.0.9 is alive
# ping 172.24.0.10
172.24.0.10 is alive
I really need help with this trouble ..and any help or advice will be thrully appreciated
Thanks
PD: any other required configuration file will be provided if is needed

Moving disks while maintaining Solaris 10 install from one v240 to another.

Hi,
I want to move a Solaris 10 install from a sunfire v240
with a single cpu to another sunfire v240 with dual cpu's. Here are the
details of the hosts as well as configuration.
I have 2 sunfire v240's. One has a single 1 Ghz cpu and the second has
dual 1.5 Ghz cpu. I want to move the disks of the single cpu host to
the host with dual cpu's. I want to keep the installed version of
Solaris 10 intact. The installation of Solaris is split across 2
mirrored disks, i.e. 4 disks in total. I am using Suns volume manager
for mirroring and also have one files system mirrored with zfs.
The questions I have are the following:
1) Can I simply shut down the servers and swap the disks to the
destination host, in the same disk slots? The controllers the disks are
on line up and are the same between the 2 hosts.
2) Will the kernel pickup the changes moving from a single 1 Ghz cpu to
dual 1.5. Ghz cpu's with out any problems? Will the kernel pickup the
faster cpu's speeds. i.e. will it know it is now running dual 1.5. Ghz
cpu opposed to a single 1 Ghz?
3) Would we have to break the mirroring on the OS before shutting it
down?
4) As another option, instead of swapping disks, could we swap the
cpus? Move the dual 1.5. Ghz cpu's to the other host? Will the
motherboards read the updates of the cpu or are their jumper settings we
would need to update?
Thanks for your help.

Box A
Sparc Solaris 9, Oracle 10g
Box B
Solaris 10 x86, Oracle 11g
I know there are many factors, but I'm pretty new to both unix & oracle, so I >needed some general steps to get me started. You have many options.
Since you're in 10g, Have the Target Database created in Solaris 10 x86, Oracle 11g.
you can use,
RMAN - Cross platform Transportable Tablespaces.
Datapump Export and Datapump import.
Read the following:
How To Use RMAN CONVERT DATABASE for Cross Platform Migration - 413586.1
http://download-uk.oracle.com/docs/cd/B19306_01/backup.102/b14191/dbxptrn.htm
http://www.oracle-base.com/articles/10g/OracleDataPump10g.php
http://www.oracle-base.com/articles/10g/RMANEnhancements10g.php#cross_platform_tablespace_conversion

Solaris 10 Install Hangs at 15% on my HP DL 585?

Solaris 10 Install Hangs at 15% on my HP DL 585
I have taken out all the additional extra cards so I am left with the basic box, it has been configured to run in Raid 1 so my four disks become two.
I can still get it to bring up a shell and do other things, but the installer just appears not to want to go pass 15%
Help?

Which version of Solaris and how much memory do you have in the system.

ZCM Reporting install failure: Wrong OS

Hi, I have downloaded the ZCM_Reporting_10.1.0.iso and would install the server on my ZCM server what is installed on a SLES 10.2 x64 with ZCM 10.1.1 x64. But I got the install message: Not supported OS. Is it true ?

I was also "bitten" by this same problem...ZCM 10.1.1 on a 64-bit SLES 10 SP2 server and when I tried to install the ZCM Reporting Server I got the same message.
It was only when I reviewed the fine print, and I do mean fine print, in the software requirements did I realize that NO 64-bit OS was going to be suitable for the ZCM Reporting Server.
Usually you would not expect to run into trouble installing a 32-bit application on a 64-bit OS but they do crop up occasionally but I was not too concerned in the case of ZCM 10.1 on a 64-bit OS about whether or not the ZCM Reporting Server would install OK. Hey, isn't this stuff supposed to work together? What happened to making IT work as one?
This does need to get "fixed" by Novell and BO because it is a problem that should not exist in the ZCM 10 world to begin with. Shame on them for being so lazy about it.
Novell should have pointed this out IN LARGE TYPE THAT THE ZCM 10.1 REPORTING SERVER CANNOT BE INSTALLED ON ANY 64-BIT OS. Instead they kind of tucked it away in the fine print where it waited to bite us.
Tim Wessels
Originally Posted by Craig Wilson
At this point in time, BOE is only supported on a 32-Bit OS.
Novell is working with Business Objects to get support for 64-Bit Platforms.
Craig Wilson - MCNE, MCSE, CCNA
Novell Support Forums Volunteer Sysop
Novell does not officially monitor these forums.
Suggestions/Opinions/Statements made by me are solely my own.
These thoughts may not be shared by either Novell or any rational human.
"deban0" <[email protected]> wrote in message
news:[email protected]...
>
> Hi, I have downloaded the ZCM_Reporting_10.1.0.iso and would install the
> server on my ZCM server what is installed on a SLES 10.2 x64 with ZCM
> 10.1.1 x64. But I got the install message: Not supported OS. Is it true
> ?
>
>
> --
> deban0
> ------------------------------------------------------------------------
> deban0's Profile: NOVELL FORUMS - View Profile: deban0
> View this thread: ZCM Reporting install failure: Wrong OS - NOVELL FORUMS
>

11g Install Failure, Listener Error.

11g Install Failure, Listener.
ORA-12514: TNS:listener does not currently know of service requested in connect
descriptor.
I am attempting to install 11g, 11.1.0 onto a stand alone box which has Windows XP SP2 as the OS.
The box is at present not networked and as is not on a domain. The computer name is homedb.
I have installed the loopback adapter on 10.10.10.10 and updated my hosts file, the computer can resolve this to the computer name and vice versa.
Upon installing 11g and the starter database, the install continues normally, succeeding with the Oracle Net Configuration Assistant. However when the Oracle Database Configuration Assistant is run, 89% of the way through an error is thrown as follows:
Enterprise manager configuration failed due to the following error -
Listener is not up. Start the listener and run EM configuration again.
Refer to the log file at C:\Oracle\cfgtoollogs\dbca\emConfig. Log for more details.
You can retry configuring this database with Enterprise Manager later by manually running C:\Oracle\product\11.1.0\db_1\bin\emca script.
When I click ok on the error message the install completes as normal.
I can TNSPING orcl which results in the following:
TNS Ping Utility for 32-bit Windows: Version 11.1.0.6.0 - Production on 20-JAN-2
008 12:36:33
Copyright (c) 1997, 2007, Oracle. All rights reserved.
Used parameter files:
C:\oracle\product\11.1.0\db_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = homedb)(
PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orcl)))
OK (20 msec)
I can connect to the database using sqlplus sys/password as sysdba but when I try to connect using
sqlplus sys@orcl and typing in the password I get the following error:
ERROR:
ORA-12514: TNS:listener does not currently know of service requested in connect
descriptor.
This is also the error I get when using sql developer to connect to the db.
The extract from the log file mentioned above is as follows:
20-Jan-2008 12:14:09 oracle.sysman.emcp.util.GeneralUtil initSQLEngine
CONFIG: SQLEngine created successfully and connected
20-Jan-2008 12:14:09 oracle.sysman.emcp.ParamsManager checkListenerStatusForDBControl
CONFIG: ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
oracle.sysman.assistants.util.sqlEngine.SQLFatalErrorException: ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
     at oracle.sysman.assistants.util.sqlEngine.SQLEngine.executeImpl(SQLEngine.java:1530)
     at oracle.sysman.assistants.util.sqlEngine.SQLEngine.executeSql(SQLEngine.java:1771)
     at oracle.sysman.emcp.ParamsManager.checkListenerStatusForDBControl(ParamsManager.java:2708)
     at oracle.sysman.emcp.EMReposConfig.invoke(EMReposConfig.java:368)
     at oracle.sysman.emcp.EMReposConfig.invoke(EMReposConfig.java:147)
     at oracle.sysman.emcp.EMConfig.perform(EMConfig.java:222)
     at oracle.sysman.assistants.util.em.EMConfiguration.run(EMConfiguration.java:460)
     at java.lang.Thread.run(Thread.java:595)
20-Jan-2008 12:14:09 oracle.sysman.emcp.EMConfig perform
SEVERE: Listener is not up. Start the Listener and run EM Configuration Assistant again .
Refer to the log file at C:\oracle\cfgtoollogs\dbca\orcl\emConfig.log for more details.
20-Jan-2008 12:14:09 oracle.sysman.emcp.EMConfig perform
CONFIG: Stack Trace:
oracle.sysman.emcp.exception.EMConfigException: Listener is not up. Start the Listener and run EM Configuration Assistant again .
     at oracle.sysman.emcp.ParamsManager.checkListenerStatusForDBControl(ParamsManager.java:2715)
     at oracle.sysman.emcp.EMReposConfig.invoke(EMReposConfig.java:368)
     at oracle.sysman.emcp.EMReposConfig.invoke(EMReposConfig.java:147)
     at oracle.sysman.emcp.EMConfig.perform(EMConfig.java:222)
     at oracle.sysman.assistants.util.em.EMConfiguration.run(EMConfiguration.java:460)
     at java.lang.Thread.run(Thread.java:595)
20-Jan-2008 12:14:09 oracle.sysman.emcp.EMConfig restoreOuiLoc
CONFIG: Restoring oracle.installer.oui_loc to C:\oracle\product\11.1.0\db_1\oui
My listener, tnsnames and sqlnet are as follows:
listener.ora:
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = homedb)(PORT = 1521))
sqlnet.ora:
SQLNET.AUTHENTICATION_SERVICES= (NTS)
NAMES.DIRECTORY_PATH= (TNSNAMES, EZCONNECT)
tnsnames.ora:
ORCL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = homedb)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = orcl)
When logged into the database a SHOW PARAMETER SERVICE results in a service of orcl
Running the command: lsnrctl service, results in the following:
LSNRCTL for 32-bit Windows: Version 11.1.0.6.0 - Production on 20-JAN-2008 12:46
:52
Copyright (c) 1991, 2007, Oracle. All rights reserved.
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1521)))
The listener supports no services
The command completed successfully.
Running lsnrctl status results in the following:
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1521)))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for 32-bit Windows: Version 11.1.0.6.0 - Produ
ction
Start Date 20-JAN-2008 12:09:10
Uptime 0 days 0 hr. 40 min. 9 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File C:\oracle\product\11.1.0\db_1\network\admin\listener.o
ra
Listener Log File c:\oracle\diag\tnslsnr\homedb\listener\alert\log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1521ipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=homedb)(PORT=1521)))
The listener supports no services
The command completed successfully
I have re run the db configuration again but it would not start because apparently there was no listener, running the Net Configuration Assistant makes no difference.
All firewalls and anti virus software have been disabled for the purposes of this install.
Do I need to manually register the listener with the database, if so how do I go about doing this?
I have installed 10g on a standalone box before with no trouble, what have I missed here?, any help greatly appreciated.

To answer my own question I fixed this by issuing the command
netsh winsocks reset
Winsocks deals with windows networking and can become corrupt through installs of software, virus cleaning, etc.
Hope that helps,
Adam

Minimize and maximize Solaris 10 installed on VM virtual Box.

How can I minimize and maximize Solaris 10 installed on VM virtual Box.
Thanks
Paulo

Solaris is working just fine. Everything is ok. now since I open Solaris via VM Virtual box, the Solaris main page fills only half of the monitor. I can minimize/maximize the Virtual Box. But Solaris dimensions are fix and doesn't change. This leaves me a little room to open applications on Solaris. I had the same problems with my Ubuntu, by installing adds-on it was fixed. For Solaris I installed Guest additions, didnt help.
Thanks
Paulo

Premiere Elements 10 install failure on Mac osx 10

I have a copy of Adobe Premiere Elements 10, the five disk set, and keep having the same failure trying to install it on my Mac. I have gone through all the product requirements and made sure that my computer satisfies them, but I still find an install failure at 51%, Exit code 7, each time.
What can I do?

I had the exact same problem installing Premiere Elements 10 on a Mac from DVD. Exit code 7 when it reached 51% installation. I followed the link to "updated installation instructions" provided in this forum by Adobe Employee Jeff Wright. It works.
The instructions in a nutshell: DON'T USE THE DVD. Instead, download a trial version. When you install use the serial number provided with your DVD.
I find this to be extremely aggravating. I spent a lot of time trying using the Adobe Support Advisor application trying to sort through the error codes. Then I spent time trying to get through to Adobe Support (never did get through). Finally I tried the forum and found the answer here.
I find Adobe to be grossly inadequate in two ways. First, they put out a product that just wasn't tested. The DVD won't install on a Mac. It is as if they did not test their product. Second, their support is awful. This is a known problem with a known solution. When the fault occurs, the Adobe Support Advisor application should point the customer to the "updated installation instructions". Instead it points to faults that are unrelated so the customer is led on a wild goose chase.
I hope the product will be better than my experience so far.

Photoshop CS5 Install failure, but on just one instance of SL (the one I

HI, I know this is a strange place to post this, but Adobe Support suggests talking to Apple, as I have an install failure of Photoshop CS5, the install app won't even initialize, and it's just on one instance of SL. I can install fine on other machines, and other bootable drives, but not on the one inside an imac (late 2008 vintage). Baffling, as the problem must be tied to this one instance...my production one. I tried other users on the machine, but no luck...same problem. I checked permissions, ran Disk Warrior, all of that, still no luck. Anyone have any other suggestions besides using Gimp:) thx,
coocoo

I can see what's going on with the installer... first it's supposed to create a temp application dir in the user account, Adobe/OOBE/blabla... then kick off the activation and then the installer. Before it get's to the activation part, it blows and deletes the dir it started. As I successfully can install on another boot drive, I tried to cobble together the installation that way, by just copying files over, and got there - pretty much. I just can't activate with my serial number as I am supposed to be able to do...probably intentionally made so - but PS is running in trial mode on my production machine, and full mode on a test machine - ha! If I could just reverse the situation I would be golden. Anyway, I have another call in to Adobe...

Adding packages from solaris 8 install disks

I need Solaris Make for Solaris 8. I have installed Solaris 8 off of downloaded Solaris 8 install disks. I apparently forgot to include Solaris Make in the install and now need to add it. When I copy the pkg SUNWxcu4t (the pkg for make and scc) and pkgadd it it claims installation is sucessful but still I have no make. It is supposed to install to /usr but there is no make there.
What am I doing wrong?
Thanks

Ok I have all of my compilling isuse resolved!
Just in case anyone else browsing this forum has the same problems here is what I have learned:
These are the relevent Packages:
for tools (ar, sccs, lex, yacc, make, nm, truss, ld, as)
SUNWbtool, SUNWsprot, SUNWtoo
for libraries & headers:
SUNWhea, SUNWarc, SUNWlibm, SUNWlibms
SUNWdfbh, SUNWcg6h
for ucb compat:
SUNWsra, SUNWsrh
You definatly need to use Solaris make (found in SUNWsprot), Solaris ar (found in SUNWbtool),
gnu tar, and gnu cc both from sunfreeware.com (I love pkg-get ^_^)
either add /opt/sfw/bin/ to your path or put a dynamic link for gcc into /usr/local/bin/ I prefer the latter.
and add /usr/ccs/bin/ to your path permanently.
Thanks for your help every one.

Solaris 10 v440 install failure.

Similar Messages

Maybe you are looking for