Solaris 10 x86 install didnt ask me for network setting?

Just realised that the install didnt ask me for any network settings
during the install...
Checked /etc/hosts and all thats there is the loopback address. How do
I set up networking now?

Dude no probs, if networking wasn't take care of at installation.
its easy to setup networking even after installation.
do the following
enter required in following files
IP in /etc/hosts
netmask in /etc/netmasks
gateway in /etc/defaultrouter-----------if file not present, create it.
& do following
# svcadm restart svc:/network/physical
walla u r done
check with ifconfig -a

Similar Messages

  • HT4145 I'm trying to hook up a desk top and it's asking me for network security code i have a apple router

    I called the help desk from the phone company they sent me to my router owner which is an apple its asking me for network security code where do ii find this

    If you still have the box and instruction manual for your Apple router then pull it out.  Find the part of the manual that tells you how to do a factory reset of the router and follow the instructions to do so.  Once it restarts, then start at the beginning of the manual and follow the instructions carefully.  They will tell you how to install AirPort utility on your computer, and then how to connect to and configure the settings on the router.
    When setting up your router's wireless settings, make sure to choose a network name with no spaces (e.g. "MyRouter"), choose "WPA2 Personal" security, and then type in a strong passphrase (twice).  Make your passphrase at least 10 characters and reasonably complex (e.g. "MyR0uter!sVery5ecure").
    Once you have made the settings, and saved them (per the manual), then you should see your new network name show up as an available network from your computer.  Select the network, type in the wireless passphrase, and it should connect.

  • HT2534 why they didnt ask me for a credit card when i set up my apple id

    Why they didnt ask me for a credit card.when i set up my apple id.

    I am having the same problem. I don't have a credit card and want to set up home sharing. HELP

  • I had a code to get logics pro for free and after it installed its asking me for a serial number does anyone know what to do from here.

    I had a code to get logics pro for free and after it installed its asking me for a serial number but it never gave me one to put in, it just started downloading and then asked me. Does anyone know what to do from here.

    I really don't think that is anywhere near on track.
    Most likely the trial version was installed earlier, is that correct?

  • Forgotten password and install-cd asks me for one, what to do?

    I have for some reason forgotten my password and i can't reset and make a new one.
    The support thingy says that to reset my password i have to use the install-cd, when i do and try to reset it asks me for password.
    What do i do? Please help!

    Have you tried a soft reset? Hold down the home and lock buttons until you see the apple icon appaer then let go. If this doesnt work, open iTunes, conect the handset to the computer and do a full restore.
    Hope this helps.

  • Wifi has suddenly stopped working. There is an exclamation mark which takes me to network diagnostics. This asks me for network name and password. This is different from the startup wizard which only asked for a WEP key and modem name. What to do?

    My wifi has suddenly stopped working on my iMac, after working fine for almost a year. There is an exclamation mark on the wifi bars and when I click it, it takes me to a network diagnostics page. This page asks me for my username and password for the wifi, which I don't have. It is different from the WEP key and modem name, which I originally used to set up my connection. I have not experienced any problems on all my other wifi-enabled devices. Ipod touch, iPad, MacBook all work fine. What should I do?

    The name is the name of the network you created on the router. The password is the WEP password. You shouldn't be using WEP at all, as it's insecure and also seems to cause connection failures. Use WPA 2 Personal. If your router doesn't support it, get a new one.

  • I downloaded the firefox but when i Run it to install , it asks me for a username and a password .. what can i do ??

    <blockquote>Locking duplicate thread.<br>
    Please continue here: [[/questions/929802]]</blockquote>
    i uninstalled the firefox cause youtube doesn't work on it and i download it again so every time i try to run the program .. and then it asks me for a password and a username when i choose Run it with the current user The message window just disappear and it stops running .. don't know what to do

    From this article:
    iTunes: About iOS backups
    Here's the answer:
    Warning: If you encrypt an iPhone backup in iTunes and then forget your password, you will not be able to restore from backup and your data will be unrecoverable. If you forget the password, you can continue to back up and use the device, however you will not be able to restore the encrypted backup to any device without the password. You do not need to enter the password for your backup each time you back up or sync.
    If you cannot remember the password and want to start again, you must perform a full software restore and when iTunes prompts you to select the backup from which to restore, choose set up as a new device.

  • HT4623 After installing IOS 6.1.3 I am now unable to install any app.  I hit the "install" it asks me for my password and then is goes back to install.

    After install iOS 6.1.3 everytime I attempt to install any app, I hit "install", it aks me for my password and then clocks for a couple of secs and then goes back to "install" without installing.

    Have you tried a soft reset? Hold down the home and lock buttons until you see the apple icon appaer then let go. If this doesnt work, open iTunes, conect the handset to the computer and do a full restore.
    Hope this helps.

  • HT4009 Hi I am having trouble buying something that is in the app it keeps asking me for 2 sets of password and it keeps telling me it's wrong

    Hi I am having trouble with purchasing an app that is in the app with the credit I have , it keeps asking me for passwords and I keep getting them wrong my new email is ***@Hotmail.com so I can not see the password  .
    <Email Edited by Host>

    We are fellow users here on these user-to-user forums, you're not talking to iTunes Support nor Apple - I've asked the hosts to remove your email address from your post (it's not a good idea to post personal info on any public forum).
    Do you mean that you are being asked for your answers to your security questions ? If you do then if you have a rescue email address (which is not the same thing as an alternate email address) on your account then the steps half-way down this page will give you a reset link on your account : http://support.apple.com/kb/HT5312
    If you don't have a rescue email address (you won't be able to add one until you can answer your questions) then you will need to contact Support in your country to get the questions reset.
    Contacting Apple about account security : http://support.apple.com/kb/HT5699
    When they've been reset (and if you don't already have a rescue email address) you can then use the steps half-way down the HT5312 link above to add a rescue email address for potential future use

  • Ios 7.1.1 can't install due to searching for network

    this update went live while my phone was out of the country- and ever since the phone is searching for a netwrok and I am unable to install the update?? not sure what to try . I have tried re-booting etc but cannot get connected to the network. HELP!!!

    Hello there digginghane2014,
    It sounds like you have not been able to connect to your cellular network on your phone, as it just keeps saying "Searching". I would use these troubleshooting steps from the following article:
    iPhone: Troubleshooting No Service
    http://support.apple.com/kb/ts4429
    Toggle airplane mode: Tap Settings > Enable Airplane Mode, wait five seconds, then turn off airplane mode.
    Turn iPhone off and then on again.
    Remove the SIM card and verify that it's a valid, carrier-manufactured SIM. Also verify that it isn't damaged, worn, or modified. Then reinsert it.
    Check for a carrier-settings update. Connect to a Wi-Fi network. Then tap Settings > General > About. If an update is available, iOS will ask you if you want to install it. If Wi-Fi isn't available, connect your device to iTunes.
    Update your iPhone to the latest version of iOS.
    Reset network settings by tapping Settings > General > Reset > Reset Network Settings. This will reset all network settings, including Bluetooth pairing records, Wi-Fi passwords, VPN, and APN settings.
    Restore the iPhone.
    If you're outside the United States, please also follow these steps:
    Go to Settings > Carrier > Automatic.
    If the phone registers any carrier network, Settings > Carrier will be present.
    If the Carrier option is missing in Settings and you're outside of the Unites States, please contact Apple for support and service options.
    Set the option for Automatic to off.
    A list of potentially available carriers appears after about two minutes. If the device is locked to a carrier, it may connect only to the carrier network to which it is locked. If the device displays carrier networks, then the device is working as expected.
    Set Settings > Carrier > Automatic back to on.
    If you're still experiencing No Service issues, contact your carrier to check for any network or account issues that could cause these symptoms.
    Thank you for using Apple Support Communities.
    Cheers,
    Sterling

  • Solaris x86 install ok, audio not working

    I have installed V10 on an MSI AMD x86 (32bit) board, coexisting with my Windows,Linux and OS/2 partitions. All works ok, except audio.
    This is an NVIDIA based board, and uses the NForce drivers. I saw one entry in the HCL about the Audio810 driver, but that didn't help.
    I need audio to work to try out the Java Desktop Accessibility features.
    ps, it works in Linux, Fedora Core 3.
    I also installed a Creative PCI Soundcard, so could use this instead. The boot time configurator sees the hardware in the PCI slot, but never does anything with it.
    help help..
    thanks
    Sam

    I ran into this as well. As soon as it detects an audio error, it shuts down the "audio server". Once you get valid drivers (or a valid card, like the Sound Blaster), you have to activate the audio server function in JDS.
    I can't remember exactly where is it located off the top of my head, but I had to do that last week when I ended up installing drivers for the Intel 82810BA audio chipset. Once I activated the audio server (or sound server or something like that), I was able to get full audio with the exception of the CD audio. I have no idea what that's about.
    I remember that I found the audio server check box somewhere in one of the GUI configuration tools. Search around. You should be able to find it after a while.

  • Solaris x86 install, but no ZFS

    Hello,
    I installed Solaris 10 x86 10/09 in a vSphere environment, but didn't get the option to use ufs or zfs during the install procedure. Is this no option? because I want to use zfs.
    # cat /etc/vfstab
    /dev/dsk/c1t0d0s0 /dev/rdsk/c1t0d0s0 / ufs 1 no
    Nevertheless during the boot I've seen the message
    Reading ZFS config: done
    -- Nick

    You have to choose the right installation type.
    You get a choice of about 5 options interactive, etc. There a note that you need to choose type 3 or 4 to do a ZFS install.
    But I can't remember which types that relates to exactly.

  • After downloading photoshop elements 12, the system started the install and asked again for the serial.  install process will NOT accept the serial #

    I purchased a software license for photoshop elements 12.  I started the process to download the software and provided the serial number on the download card.  Since the serial number provided was correct, the download started and completed.  Once installed the system started to install the software.  Again I had to supply the serial number.  This time the system will NOT accept the serial number.  I entered it again.  Not accepted.  I tried it again, this time with dashes.  Again the serial number is not accepted.  What do I do?

    Is there any message provided when serial number is not accepted?  If so, what does it say?

  • Acrobat Pro 9 Upgade won't install. Asking me for prior serial numbers.

    HD creash on Win 7 654 bit Pro. Can't install my Upgrade disk and serial. Gets accepted, but when I open the install,I'm then prompted to enter the version and serial of my previous version. I can't remember thevwersion. I havee 2 additional serialss for previous versions. but don't recall the versions or types. I've been using Adobe for 20 years.
    Tryingg toget back to normal on a jnew C drive andiss it painful.

    Hi jerry forbes,
    Please check the inbox for reply.
    Vikrantt Singh

  • TS2529 After restoring to factory settings my iPhone 4 is asking me for nework settings I only have emergency calls?

    AFter updating my iPhone4 my phone crashed and had to be set to factory settings now I can only use it for emergency calls. It is asking me for network setting? I have tried o2 but this has failed. Please help.

    Sounds like your phone has been re-locked to the carrier it was originally locked to, which is not O2. Where & from whom did you get this phone?

Maybe you are looking for