Solaris 11 VM from template does not boot

Not sure if this is the right forum (or if it should be in the Solaris section).
I just cloned a Solaris 11 client using the Solaris 11 template I imported from Oracle. After going through the setup screens, the VM starts to boot but hangs on the "Oracle Fault Management" (fmd) service. It seems to be hung in the start method as there are no logs, errors, or anything after the entry about running "start".
Anyone else have this problem? If I create a Solaris 11 VM using the installation ISO and an empty disk image am I up in running in no time. Seems like the template is kind of useless.

I am experiencing this too. We are testing Solaris 11 from the template provided by Oracle.

Similar Messages

Usb recovery media made from t430i does not boot

hi i got a problem here
a friend got e new t430i with windows 7 pro 64 bit
so he asked me to install windows 8 he gets from his university on his t430i - therefore i started the rescue and recovery programm via lenovo solution center and did all with a 32 gb flash media.
the flash media is set active but the the recovery system does not start of it but the R&R does not let me do the whole process once again this time on som DVD's
so how can i do the whole process once again - as otherwise i could not install win8 without loosing the ability to set the system back to win7 factory defaults ?

RnR is not available for win8 systems.
I assume you are trying to backup up the Factory recovery partition on the win7 system to use in a far future time, ie like if pc is sold.
You are trying to CREATE PRODUCT Recovery (factory install ) backup. This is only allowed to run 1 time.
(1) Create USB backup wont boot (you have to prep the usb before the backup).
(2) cant run process a second time. You have to change DONE_ini parm inside the recovery partition to allow it to run again.
Both of these issues are discussed in other posts on here.
http://forums.lenovo.com/t5/ThinkVantage-Technologies/Problem-with-usb-recovery-media/m-p/1038829#M2...

Clicking "page from template" does not allow me create new pages

I stared designing a site with the trial version of CS4. Of course it involved a lot of trial and error, creating a page and canceling it again etc. At last I was able to design the index page and a few other pages, but suddenly just about 7 days into the trial period, the template started looking different; not displaying the images and displaying the home page article in an improper way. I also discovered that I could not create new pages by selecting file\new. When the new document dialogue page opens and I select "page from template" and then select a site I am working on, nothing shows in the items list. I only see the message "no items". Moreover, the "create" (new page) button is no more a click-able area.
I even tried it by proceeding as if I wanted to design a new site. I click file\new\page from template\the site, but when it comes to the stage where I should select "2 column liquid, left sidebar, header and footer" after clicking “page from template” I don't see anything in the items column. It only tells me "no item."
I thought this problem was due to the fact that I was using the trial version and that the trial version was limited in the number of new pages I could create. So I bought the full version. Alas! I discovered that changed nothing. Right now am stuck. Do you have any suggestion?

I think you're are confusing DW Templates with CSS Page Designs and Starter Pages.
Templates are a DW proprietary device. They permit you to have sitewide elements such as common menus, headers and footers on all your pages along with Editable Regions for page specific content (i.e. the stuff that changes on every page).
DW Templates looks like this (notice the Template Editable Comments):
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1" />

<title>Untitled Document</title>



</head>
<body>
My Page Specific Content Goes here

</body>
</html>
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
http://alt-web.com/
http://twitter.com/altweb
http://alt-web.blogspot.com

Boot failed: solaris server does not boot

Hi All,
one of my support person who has administrator previlages tried move the contents of root to trash directory, in the middle it got hung,and he had restrted the server.
Now the solaris does not boot. It says
boot failed
Enter Filename [platform/sun4v/kernel/sparcv9/unix]
and what ever we enter there it says boot cannot read.
Please suggest some workaround, nearly 200 users are down, actually it is our licnese server.

Hi,
What you could try is the following :
Boot the system from the solaris cd into single user mode.
Find out what the disk is you need to mount and mount it under /a
After you have done this you can see if you can move back the stuff that was moved from the root directory to the trash.
If that works then you could try and boot again from the disk to see if everything works again.
Nico

Reset Password - System does not boot from DVD

My System: Macbook Pro - 2Ghz Intel Core Duo - OS X - 10.6.8
Hi everyone,
i forgot my password. So i want to boot from install DVD to reset the password. Unfortunately my macbook pro does not boot from DVD (10.6.3).
I press c all the time...but sometimes the macbook pro throws the DVD out...and sometimes nothing happens.
The DVD drive is working fine...
Any other idea?
Thanks in advance.
Fabian

So when you boot holding option it shows a padlock with a password field? Is that correct?
In that case we're talking about the firmware password, which you can't reset via the install disk. There is only one way to do this, I'm not certain if one is allowed to divulge that information publicly - might want to try googling "reset firmware password"

Importing element definition from an EDD into a template - does not work

FM 10.0.1 German on Windows XP SP3.
When importing the element definitions from an existing EDD into an existing template, FrameMaker converts the template into a new EDD.
So the element definitions which are correctly defined do not appear in the template.
The highest level element is than ElementCatalog in the template and not the higherst lvel element defined in the EDD.
In FM9 this was no issue.
Any help is appreciated, I have a deadline and must do some changes in the EDD.
Best Regards
Thomas

Lynne,
EDD is english (Version FM7.0), Interface language is German.
Maybe it´s a localization issue.
I have attached a captivate demo pdf so you can see what happens and the
defective EDD.
Mit freundlichen Grüßen
Best Regards
Thomas Zeisig
From:   Lynne Price <[email protected]>
To:     "Th. Zeisig" <[email protected]>
Date:   13.10.2011 14:12
Subject:        Importing element definition from
an EDD into a template - does not work
Re: Importing element definition from an EDD into a template - does not
work
created by Lynne Price in FrameMaker Structured - View the full discussion
Thomas,
No question the behavior you describe is a bug. However, I am unable to
duplicate it. I created an EDD with two element definitions:
Element (Container): doc
Valid as the highest-level element.
General rule: (
When I imported element definitions from this EDD into a new portrait
document, FM reports that element a is referenced but not defined and that
b is defined but not referenced. However, with all elements listed, the
element catalog shows a, b, and doc. The metatemplate elements are not
available.
I wonder if this is a language-dependent problem. Is your EDD German or
English? What about your user interface?
Can you send me a short EDD that fails as you've described?
Thanks,
      --Lynne
Replies to this message go to everyone subscribed to this thread, not
directly to the person who posted the message. To post a reply, either
reply to this email or visit the message page: [
http://forums.adobe.com/message/3969067#3969067]
To unsubscribe from this thread, please visit the message page at [
http://forums.adobe.com/message/3969067#3969067]. In the Actions box on
the right, click the Stop Email Notifications link.
Start a new discussion in FrameMaker Structured by email or at Adobe
Forums
For more information about maintaining your forum email notifications
please go to http://forums.adobe.com/message/2936746#2936746.

MSI P6N SLI V2 does not boot up from cd/dvd and few other problems

HI
I just bought a computer P6N SLI V2 + E6750. It has following problem. It does not boot from cd.
I have Sata HD. CD/DVD is installed to IDE as a master.
I have done settings in bios so that First boot is cd/dvd and second is sata HD. Anyhow it still goes to the hd and stars windows.
I was only able to boot up from cd when I disabled hd from boot sequency. Meaning I left only cd/dvd there.
Hopefully you pro's can help me.
Then there is another problem. Windows is telling me that it found new pci device. I do not know what device. I have only Graphig card (geforce 8800 gts) installed into pci-E. Drivers and software are also installed, I assume proberly. How to find out what windows thinks it found.
Third problem is onboard soundcard. I cannot get any sound out from the machine. I have downloaded driver from realtek, but still no sound.
Unfortunatelly I do not have original software for motherboard. Only the latest from MSI website.
Hopefully someone can help me.
thanks.

About bootup, i dont know yet.
To find out what windows found, look in devicemanager.
To go there go to controlpanel, system then choose devicemanager.
There you can see what's installed.
Last, your soundcards needs to be enabled in bios, under integrated peripherals there should be a line with "onboard sound", enable this and sound should work, unless its broken.

Satellite P840/016 does not boot from CD or DVD

Using F2 enabled the BIOS to boot from optical drive, saved and re-started. Finds the bootable CD created from the same laptop using the repair disc from Windows 7 recovery but does not boot.
Tried Ubuntu DVD which works as boot disk on all other laptops - still does not boot.
Changed the setting in BIOS to non-secure - same problem.

Thanks - tried this pressing F12. Message appears on the screen to press any key to boot from DVD. Key pressed, the DVD is read and then delay with blank screen. The laptop goes back to start screen and than goes to boot from the HDD. Also tried making USB as bootable. Pressed F12 and selected USB as boot device. Reads the USB and after a period of time boots from HDD.
Checked DVD driver - it is the latest.
Operating system is Windows 8 pro.
RAM is 8GB, processor is I7 and HDD is 1 TB. Laptop is only 3 weeks old

HT4061 I have an iphone 5s, does not boot, blinking white screen with black logo, when trying itunes restore from mac and pc, error code 4013 which is usb error, any ideas?

I have an iphone 5s, does not boot, blinking white screen with black logo, when trying itunes restore from mac and pc, error code 4013 which is usb error, any ideas? Does a totally dead battery have that effect? I have had it plugged in to a computer overnight, but maybe does not charge when totally dead?
Please help, thanks in advance all1

Hi eggroll77,
Welcome to Apple Support Communities.
That alert codes does suggest there is a USB related issue. If you haven’t already, try the troubleshooting suggestions in the article linked below.
iOS: Restore errors 4005, 4013, and 4014
I hope this helps.
-Jason

New MBP i5 does not boot after hard disk swap

Hi there,
I received my new i5 MBP today. After booting it once with the installed HDD to check if it's ok, I exchanged the hard disk for the one in my Late 2008 Macbook Pro. After doing this, my Late 2008 Macbook Pro boots fine with the (new) hard disk from the new i5 MBP, but the i5 MBP does not boot with my old hard disk.
To give you some details:
- I have installed 10.6.3 on the (old) hard disk that's not booting.
- The i5 MBP boots fine from the installation DVD
- Disk utility finds and can read my hard disk, no errors
- PRAM NVRAM reset did not help
- when booting in safe mode, I can see the system stop booting after or while loading Extensions.mkext
My guess is, it tries to boot and load the wrong Extensions for the new system (CPU? GPU?). I have no idea how to fix this.
Any help would be greatly appreciated!

Focx,
Welcome to Apple Discussions.
Inserting the drive from an earlier model MBP will probably not work. The version of the system you have on that HD is designed for earlier hardware so when you put in in your new machine it's going to be recognized. What I'd recommend is re-installing the disk that came with the new machine and of course putting the 2008's disk back in the old machine. Then use Migration Assistant on the new machine and migrate your data from the old machine into the new machine.
This will provide a much more stable system and should work just fine.
Regards,
Roger

Satellite L745D-S4214 Does not boot; HDD recovery partition not working

I tried to apply the recent windows 7 updates and my laptop no longer boots. I tried to press F12 and select the HDD Recovery partition, but it does not boot regardless. There is a message that it does not communicate to a specific device. I believe the address called out was 0xc0000e9, but I am going by memory. I never created a recovery CD because I thought I was covered by the HDD partitions. This was purchased on 10/26/2012, so it should still be under warranty.
PLEASE HELP!

Hi I'm going to assume that your recovery works like mine and that the recovery partition is still good and not corrupted.
Shut down your PC. Press F12 and select HDD recovery. Click enter. This should start the recovery from the hidden recovery partition.
PS I would advise you to make the recovery discs or USB recovery Try this first.
Perform a power cycle
Even when your laptop is off and unplugged, residual power can still be held in some components. While this is normal, clearing it can help with boot problems. Perform these steps to complete what’s called a power cycle.
Ensure the laptop is turned off.
Unplug the laptop's AC power cable.
Remove the battery (if the model has a removable battery).
Unplug all wires or peripherals. This includes CDs, DVDs, USB sticks, mice, printers, and any other accessories.
Hold down the power button for thirty seconds.
Reattach the battery.
Connect the AC adaptor to the power socket that was confirmed to be working in the first step.
Connect the other end of the AC adaptor to your computer.
Try starting the computer.
If your laptop starts normally now, you're done!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

Satellite M30-107 does not boot correctly after Recovery disk usage

Hi
I've recently got hold of a second hand toshiba Satellite M30-107 laptop, and decided to freshen it up.
I used the toshiba recovery disk, but after doing so the laptop no longer loads windows.
When turned on it shows the Toshiba start up disk for about a second then goes to a blank screen and freezes.
When turned off and on again a screen comes up reporting an error in shutting down and gives the options to start in safe mode etc. but choosing any of the options causes the machine to freeze.
Any help or advice would be much appreciated.
Thanks
jt

Hi
Sounds a little bit like the notebook does not boot due to the Windows software issue
Did you recover the M30 with the original Toshiba recovery CD which was supplied with this M30 unit?
Maybe Im wrong but for me it looks like a wrong recovery CD was used and an image with non compatible drivers was installed
You could try to install the OS from original Microsoft Win XP CD and could check if it would be possible to get the notebook ruining using clean OS.
In such case we ( you and me ;) ) could find out if this issue could be related to the software or hardware.
Bye

Toshiba Satellite P870 upgraded to Win 8.1 does not boot

I have a Toshiba Satellite P870 with Win 8 preinstalled. Soon after upgrade to Win 8.1 and basically successful removal of “watermark error” (secure boot activated) the machine stopped booting completely: after pressing the power button ventilator sound
is heard with periodically changing loudness as well as clicking sound from the speakers. The screen stays black. Attempts to start the PC through pressing F2 or zero buttons did not produce any result. Neither did I succeed with recovery discs I created before:
the system simply does not boot from the disk. It looks like I tried all options offered by Microsoft and Toshiba. I would be happy to roll back to factory settings.
Could someone give me hint what to do next?

Hi,
For the issue, let us know how to remove the “watermark error".
Meanwhile, I would like to confirm if you could access the BIOS.
I suggest you update the BIOS version to test it.
If you want to repair the startup issue, you should use windows 8.1 recovery discs or installation discs.
Meanwhile, if you cannot access the BIOS, it may be caused by hardware, I suggest you contact the Toshiba manufacturer for further help.
http://support.toshiba.com/
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact
information.
Regards,
Kelvin hsu
TechNet Community Support

Satellite A105 WIN XP does not boot or load...

Ok, so my wife's laptop has a boot issue. Model is A105-S4284
The Toshiba/Phoenix screen loads, but does not boot/load XP. It gives a black screen, then sits for a few secs and restarts. it will continue this loop indefinetely as far as I can tell. When this happened, she complained that it has been taking longer for it to boot into XP recently. (Wish she had told me before)
I can get to BIOS system utilites, Boot menu, and can access F8/Win Advanced options boot choices. I have tried the following:
Safe Mode
Safe Mode w/command prompt
Last known GCFG
Disable Auto restart on failure
I have also done a battery pull and unseated the memory, even swapping left/right, and attempted boot from just one mempry module, all with no change.
Apparently her DVD/optical drive is toast (apparently has been) so I can't do a recovery disc, but I did make a recovery USB drive. No dice there either.
What have I not done? Since I can access the adv. opt. menu it seems winXP is still there. most likely she shut it down while XP was installing something, and now there is some type of error in the registry or somewhere, but I can't seem to recall or remember what my next steps would be to gain access to I can try to clean it up and recover.
I would do a complete wipe and start from scratch, but her entire work portfolio is on the HDD and she (foolishly) has not backed it up, at least not recently. Is my best bet to get an outboard drive enclosure and set the jumpers to slave, so I can attempt to recover the data that way?
I'm a bit stubborn, and know my way around a computer, and I refuse to give up and drop it off at the geek squad.
Please help!

Satellite A105-S4284
her entire work portfolio is on the HDD
First things first. You should rescue the files.
Remove the hard drive and place it in an enclosure accessible from a desktop via USB.
-Jerry

Macbook pro does not boot after upgrading ram

I have a macbook pro late 2011 which runs with mavericks operating system . I have tried to upgrade my macbook to 8Gb. Macbook does not boot when the two ram slots are filled with 4GB ram but runs well when the slots are filled with 2GB ram. When i try them individually with one slot of 2GB ram and another slot with 4GB they run perfectly which shows status ok in the RAM info. What could be the problem .

Around here, most of us recommend only Crucial and OWC for RAM because it's guaranteed to work with Macs and it's what most of us have. If I were you, I would return the RAM and look at purchasing RAM from either Crucial or OWC. If you can't get their RAM to work then you'll know that there's some trouble with your actual slots.
Good luck,
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

Solaris 11 VM from template does not boot

Similar Messages

Maybe you are looking for