Solaris 8 on a Sun Fire v480 (full vs half duplex)

Hi All
I've installled Solaris 8 on a Sun Fire v480.
Now, when I boot I get the following (via serial A/LOM):
{2} ok boot -r
Boot device: /pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w2100002037cfdf9d,0:a File and args: -r
SunOS Release 5.8 Version Generic_108528-13 64-bit
Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
configuring IPv4 interfaces: ce0.
Hostname: abcdef
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
Configuring /dev and /devices
NOTICE: ce0: fault cleared external to device; service available
NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
Configuring the /dev directory (compatibility devices)
The system is coming up. Please wait.
checking ufs filesystems
/dev/rdsk/c1t0d0s5: is clean.
/dev/rdsk/c1t0d0s7: is clean.
starting rpc services: rpcbind done.
Setting netmask of ce0 to 255.255.224.0
Setting default IPv4 interface for multicast: add net 224.0/4: gateway abcdef
syslog service starting.
Print services started.
volume management starting.
The system is ready.
abcdef console login:Dec 22 11:01:34 abcdef picld[70]: Device PS1 AC UNAVAILABLE
Dec 22 11:01:35 abcdef picld[70]: FSP_GEN_FAULT_LED has turned ON: 1 failed device(s)
abcdef console login:
My question is what is going on. I see 2 things:
1)
NOTICE: ce0: fault cleared external to device; service available
NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
what does the first line means and why half duplex and not full
2) FSP_GEN_FAULT_LED has turned ON......
hmmm, what does this mean ?
Any suggestions to help me untangle those messages ?
Thanks a lot in advance
Luca

Hi,How to set my link up in solaris 10 ?
I dont know want happend to my machine solaris v440 it suddenly disconnected from n/w and finally i came to know that is a problem with NIC card..i din't find any light's glowing back side of the machine at NIC card.
can any one help me in this pls how can i proceed furture for getting my NIC back?
and i have excuted few commands
#ndd -set /dev/ce instance 0
#ndd -set /dev/ce adv_1000fdx_cap 1
#ndd -set /dev/ce adv_autoneg_cap 0
I have got dladm show-dev is
ce0 link: unknown speed: 1000 Mbps duplex: full
ce1 link: unknown speed: 0 Mbps duplex: unknown
I dont understand that why my link is showing still unknown ...any help..

Similar Messages

Unable to use Auto setting or 100BaseTx in either full or half duplex!

Hi here is the issue, I have a small home network of three desktops, one laptop (wireless) and two game consoles with a WRTP54G router and cable modem. I have noticed that if I try to change the NIC setting on any device to either Auto or 100BaseTx in either full or half duplex the connection drops. The pc will say network unplugged, the minute I change it back to10BaseT in either full or half duplex it comes right back up! Before anyone asks yes my NIC's are 100BaseTx compatable. I have made sure all drivers are up to date. Has anyone had this issue? I would like to use 100Base Tx in Full Duplex! Any help would be appreciated!

hi. the auto sense feature of the router is not working anymore. i dont know if a firmware upgrade will help, but you can give it a shot.

Installation of Solaris 8 in Sun Fire V215

Hello.
I'm trying to install Solaris 8 on a Sun Fire V215 which comes with Solaris 10 pre-installed. I'm doing so because some of the software we developed seems to have problems onSolaris other than version 8.
Is Sun Fire V215 compatible with solaris 8??
I get the following error when trying to install SOlaris 8 update 2/04 from a CD:
Invalid install CD-ROM for karch "sun4u"
I've been looking all over the documentation of SUn Fire V215 to see whether it was possible or not to install such an old version of Solaris, but unluckily I never found anything. Can anyone help me?
Thank you very much
Jorge

That is not ever going to work.
Solaris 8 is a discontinued product.
That hardware will only work with SOlaris 10 and one specific release of Solaris 9.
http://sunsolve.sun.com/handbook_pub/Systems/SunFireV215/SunFireV215.html
If you want a more complete explanation,
go back to your Sun sales representative, else open a support case with Sun.

Migrate Solaris 10 from Sun-Fire-V240 to T5140

Hi everyone.
Is it possible to migrate Solaris 10 running Oracle 10g RAC on a Sun-Fire-V240 to a T5140 without having to reinstall OS + Oracle-DB-software from scratch?
Because both servers are based on a SPARC-processor, I am guessing that it should be possible to patch/configure the OS to run on a T5140 instead of a V240.
Well, I have tried the following:
1) Booting the T5140 using "disk1" (c1t0d0).
2) Formatting "disk2" (c1t1d0) in the same number of slices I have on the V240.
3) newfs on every slice, mounting and copying from V240 to T5140 using "ufsdump/ufsrestore" over ssh.
4) Editing the /etc/vfstab.
5) installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c1t1d0s0
...Because I haven't got the correct platform for T5140 on the V240-install (even though it is patched recently), I used the one on the T5140.
6) Removed the /etc/path_to_inst and tried to "boot -ar" (after switching disk2 to "disk1-controller-position").
When 1-6 did not work, I tried a few other things:
a) Replace the /platform and /usr/platform with the ones on the T5140 (Generic_137111-06 sun4v sparc SUNW,T5140).
b) Replace the /kernel with the one from the T5140 (Generic_137111-06 sun4v sparc SUNW,T5140).
c) Replace the /etc/path_to_inst with the one from the T5140.
No luck so far.
So I am left with my initial question - is it possible to patch or configure the V240-Solaris10-installation, so it will run on a T5140?
Thanks,
Niels

In theory you can, but the question is if you want the issues. Migrating between architectures is only recommended for sparse zones, but not for any other. In this case it's you go from sun4u to sun4v which will give you enough of issues beside te changing hardware paths and configuration items.

Clone the Solaris OS from Sun Fire X4200 M2 to Sun Fire X4100 M2

Dear all,
May anyone help me?
I want to clone the all slices (whole hard disk) in Solaris 10 OS from Sun Fire X4200 M2 Server and then restore it back to Sun Fire X4100 M2 Server. Is it possible to do this? If "Yes", may show me how to do it?
I appreciate for your help.
Thanks you in advance,
Soret,

Hi.
It's possible, but depend of used file systems, used or not voluem manager, hardware configuration.
Possible steps:
1) Make Backup x4200 ( on internal disk or third NFS storage )
2) Boot x4100 from installation DVD in to Single user.
2.1 Partitioning disk
2.2 Create New FS
2.3 Restore backup on new FS. ( need configuree network, and mount disks with backups over NFS )
2.4 use devfsadm for rebuild device tree
chroot <new_root> devfsadm
2.5 Make neaded customization on new system.
2.6 Install grub and bootblok ( installboot )
2.7 Umount all new FS; halt system.
3) Try normal boot new system.
Some step for create new disk you may do on original server. Install new disk and make restore on it.
After- return this disk to x4100.
Regards.

Failed to install solaris on new "Sun Fire V100"

Hi All,
I'm new to solaris. I have a new server Sun Fire v100. Just after power on the server I got a following message on the console screen
*" No memory Detected! Cannot proceed further !!!"*
Actually I want to install solaris 10 update 4 on this server.
Any help would be greatly appreciated.
Thanks,
Sachin

That system may be new for you, but Sun stopped selling them in March 2006.
Now, as for the "No memory Detected" message ?
There are four DIMM slots on the systemboard.
Make sure they actually have RAM installed to them.
The manuals for your "new" V100 can be found at:
http://docs.sun.com/app/docs/coll/v100

Please could you tell me what DLT/SDLT/Ultrium series drive works with Sun Fire V880 with SCSI Sun X

Please could you tell me what DLT/SDLT/Ultrium series drive works with Sun Fire V880 with SCSI Sun X6540A?
The question is URGENT because we need to do backup/restore of our Databases but we have not backup device...
We want to buy it but we don't know what exactly drives we can choose for our Sun with X6540A SCSI card.

Hello,
the X6540A is a Dual Single-Ended Ultra/Wide SCSI (PCI) controller. The controller is only upto 40MB/sec, which might be suficient for a SDLT600 or LTO-2.
Every Single-Ended SCSI device works with this card, but performance would be low when using LVD/SE devices (some LVD devices can't operate in SE mode!)
I would suggest that you call Sun Sales.
I guess that the PCI/PCI-X Dual Ultra320 SCSI Adapter (SG-XPCI2SCSI-LM320) or PCI Dual Ultra3 SCSI Host Adapter (LVD) (X6758A) are a better choice if attaching more recent drives.
This is the Sun Fire V880 - Full Components List.
Michael

Solaris 9 in a Sun Fire V100 Box ServerSocket Bug

I am running Solaris 9 in a Sun Fire V100
I am having a problem openning Sockets where programs are written in Java.
The program is written in Java with the ServerSocket class.
I wrote a very simple class to test.
The port is available of course I already verified it.
I checked with the SecurityManager to verify this is not a
security policy but I receive a null from the System.getSecurityManager
which means there is no securityu manager installed.
I have many other apllications that are able to open ports and listen, but Java seams
to be having problem in Solaris 9. I have tried 5 different versions of Java. Last version
I tried is jsdk 1.4.2_05.
The same thing happens with Tomcat that crashes while
trying to open a listening Socket.
ServerSocket server;
try
server = new ServerSocket(8005,1024, InetAddress.getByName("127.0.0.1"));
System.out.println("BINDING SUCCESFUL");
catch(Exception e)
System.out.println(e);
System.exit(-1);
while(true)
try
Socket clientSocket = server.accept();
ClientHandler2 t = new ClientHandler2(clientSocket);
t.start();
catch(IOException e)
System.err.println( e );
Is this a well known bug...
Can anyone be so kind to help me up with this terrible matter
Thank you,
Juanpablo Lajud

Hi,How to set my link up in solaris 10 ?
I dont know want happend to my machine solaris v440 it suddenly disconnected from n/w and finally i came to know that is a problem with NIC card..i din't find any light's glowing back side of the machine at NIC card.
can any one help me in this pls how can i proceed furture for getting my NIC back?
and i have excuted few commands
#ndd -set /dev/ce instance 0
#ndd -set /dev/ce adv_1000fdx_cap 1
#ndd -set /dev/ce adv_autoneg_cap 0
I have got dladm show-dev is
ce0 link: unknown speed: 1000 Mbps duplex: full
ce1 link: unknown speed: 0 Mbps duplex: unknown
I dont understand that why my link is showing still unknown ...any help..

Sun Fire V490-Internal FC Drives missing in Solaris 10 installation program

Hi,
We have a V490 server that we are attempting to configure, but the internal FC drives are not available to the Solaris 10 installation program.
The OpenBoot SCSI test fails:
{3} ok test-scsi
Testing /pci@9,600000/SUNW,qlc@2
ERROR : ISP2200 RISC engine did not generate expected interrupt.
DEVICE : /pci@9,600000/SUNW,qlc@2
SUBTEST : selftest:loop-tests:inquiry-test:disk-test
CALLERS : (f010f69c)
MACHINE : Sun Fire V490
SERIAL# : 66233440
DATE : 03/27/2012 14:27:32 GMT
CONTR0LS: diag-level=max test-args=
/pci@9,600000/SUNW,qlc@2 selftest failed, return code = 1
but the probe of the SCSI bus does not and displays the drives:
{3} ok probe-scsi
This command may hang the system if a Stop-A or halt command
has been executed. Please type reset-all to reset the system
before executing this command.
Do you wish to continue? (y/n) y
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 500000e010192d11 FUJITSU MAP3147FC 0110
1 1 0 21000014c320ff73 SEAGATE ST314670FSUN146G055A
How can we fix this problem?
Thanks.
S Kayal
Edited by: 923748 on Mar 27, 2012 10:59 AM
Edited by: 923748 on Mar 27, 2012 11:00 AM

I don't think the test-scsi command is viable for that platform.
The FC disks are "viewed" by the system as external to the SCSI controller, almost as if they were in a multi-pack.
They are FC drives addressed by the chipset as SCSI disks.
Try:
<pre>probe-scsi-all</pre>
Edit:
Which release of Solaris 10 are you trying to install?
Older releases that might be fine for V480's won't work on V490's.
Edited by: rukbat on Mar 27, 2012 2:35 PM

How to flash bios on Sun Fire X2100 (without cd/dvd drive ) from solaris.

Hi I have the following problem. I need to udpdate bios in my sun fire x2100 (not the m2 version). Installed system on it is the latest solaris 10. I have also one laptop with sxce b107. I need to update bios to support zfs root/mirror.
Both devices are int the one subnet.
I download supplement cd from sun, but I was pretty amazed that there is available only remote update from rhel (32bit) or boot from cd/dvd drive.
Any help is welcome.
Lubos Kocman

1. If an OS is installed:
- log in as you described
- shutdown the server with `init 0`
- this should bring you to the OK prompt
- Insert the bootable system software CDROM into the CDROM drive
- On the OK prompt, type `boot cdrom`
2. If no OS is installed:
- connect to the serial management port with your PC (Hyperterminal)
-> NOTE: you will need a DB-25 Adapter (Part No. 530-2889)
connect this adapter to the serial port of your PC, then connect the adapter
with an RJ45 cable to the serial management port of the server
-> Serial Port Settings in Hyper Terminal:
Duplex: Full
Bit Rate: 9600
Parity: None
Databits: 8
Stopbit: 1
Flow Control: Xon/Xoff
VT100 Emulation (if applicable): ON
- change to the OK prompt by typing `break`
-> if this does not work, try `reset -x`
- make sure your OS Installation CDROM is in the drive
- at the OK prompt, type `boot cdrom`

On Sun fire v490 - Solaris 10 with Oracle 8.1.7.4 & Sybase 12.0

Hi,
We are going to upgrade our server with this configuration -
Sun Fire V490     2 x 1.05 GHz UltraSPARC IV CPU
8096MB RAM     2 x73GB local disk
2x FC 2GB Sun/QLogic HBAs
DAT72
On one machine we will have Sun Solaris v10 with
Oracle DB v8.1.7.4 & Second one will be Sun Solaris v10 with Sybase DB v12.0.0.6.
Now our question is - Sun fire have Hyper-thread CPUs �� will the O/S and databases (Oracle and Sybase) view the proposed system as a true 4 CPU platform? Will parameters used to tune the database such as Sybase max online engines still operate in the same manner as before?
Our old machine configuration was - Sun E450     4x400MHz CPU     1024MB RAM     2 x18; 8x36GB disks

Questions on Oracle and Sybase should be directed to a database forum, this forum is for Sun hardware support.
Here is a link to a DB forum I look at from time to time:
http://www.dbforums.com/index.php
The topic of tuning Oracle or Solaris is way beyond the scope of this forum, I have attempted to go into it before but didn't get any feedback and I would only like to spend lots of time on it if I was being paid!!! On the memory side, keep in mind that Oracle 9i 64-bit can address a maximum of 2 ^ 64 ( 16777216 TB ) memory, prior to that the DBA had to define memory parameters in init.ora. To be honest the last time I worked with a Oracle 8 database I shut a HP K class server down permanently that had been migrated to Oracle 9i on Solaris by an Oracle consultant and I can't remember all the tuning trick etc.

Solaris 8 & Sun Fire 280

Does Solaris 8 support 32-bit kernel ?
Does Sun Fire 280 boot Solaris 8 32-bit kernel ?

I just installed Solaris 8 on an old Ultra1 and it is using 32bit versions, now, if I can get this X working....

Couldn't upgrade Solaris 10 x86 from Sun Fire x2200 to Dell Precision Wrkst

Dear Solaris Experts,
I need to clone a Solaris 10 x86 system using a ufsdump backup from the following source & target servers:
Sun Fire x2200 M2 with Quad Core Processor
# /usr/platform/`uname -i`/sbin/prtdiag
System Configuration: Sun Microsystems Sun Fire X2200 M2 with Quad Core Processr
BIOS Configuration: Sun Microsystems S39_3D12 10/06/2008
# uname -a
SunOS old 5.10 Generic_139556-08 i86pc i386 i86pc
to
Dell Precision WorkStation 390
# /usr/platform/`uname -i`/sbin/prtdiag
System Configuration: Dell Inc. Precision Workstation 390
BIOS Configuration: Dell Inc. 2.3.0 05/01/2007
# uname -a
SunOS 5.10 Generic_139556-08 i86pc i386 i86pc
Unfortunately, Solaris kept rebooting (failed to boot) from the restored primary disk (both / & /export/home) even though Grub menu appeared. As a result, I have embarked on the path of upgrading path using the same Solaris 10 Installation Disk (5/09) DVD but failed due to not able to mount / (c0t0d0s0), swap and /export/home (c0t0d0s7).
The source Sun Fire x2200 had two mirrored disks but I am restoring the backups to a single harddisk. Any idea on what step has been missed or that it is not possible to go down this path altogether.
I have tried a number of different reinstallations & restores but have not had much luck still.
Many thanks,
Jack

I should have searched the forums first. This was the solution to my issue....
http://forum.java.sun.com/thread.jspa?messageID=10249826

Re: Sun Fire v490 / Solaris 9 booting from CD, Network problems

Hi Folks,
Apologies in advance for the length of this post.
For the purposes of disaster recovery I have built a custom CD based on the Solaris 9 installation disk with our third party backup / restore software included on it.
After the rcS script has setup networking it runs a bash shell so that I can label / partition / format the hard disks as necessary then use the third party software to recover the system.
This works fine on almost all the machines we've tested (Ultra 10s, Ultra 30s, FS Prime Power 400)
On one Sun Fire v490 however I seem to have problems with networking...
Part of the customised rcS script makes the following call
ifconfig ce0 10.4.20.20 netmask 255.255.0.0 upto configure the NIC. However when the rcS script leaves me at the shell I'm unable to ping anything.
The output from ifconfig - a looks like...
lo0 flag=..
inet 127.0.0.1
ce0: flags=1000823<UP BROADCAST,NOTRAILER,MULTICAST,IPv4>
mtu 1500 index 2 inet 10.4.20.20 netmask ffff0000 broadcast 10.255.255.255 ether 0:14:4f:0:be:beThe only thing that looks odd to me is that there's no "RUNNING" entry for ce0 that I get if I boot from the same CD on my other machines (Ultra 30s & Ultra 10s)
The broadcast address looks wrong, but again it's the same when I boot from th CD on my other test machines and they all seem to work.
I'm pretty sure that ce0 is "plumbed", 'cos if I "unplumb" it from the shell prompt then it doesn't even appear in the output from ifconfig.
Someone has suggested that it's a connectivity issue, but if I boot normally rather than from my custom CD then the networking is fine.
As a test I tried removing the drivers for hme from the CD then booting one of my Ultra30s but in this case the entry for hme0 was completely absent from the output of ifconfig.
So I've concluded that the driver for ce0 is at least there on the v490.
So for the moment I'm confused as to why the ce0 appears on the output for ifconfig, but has no RUNNING 'flag'
Anyone got any ideas
Many thanks in advance
Regards
Kevin

hello
you have an error in your interface configuration
you should have
you are using a class A ip adress but with a class B netmask
ip 10.4.20.20
netmask 255.255.0.0
broadcast should be 10.4.255.255
Message was edited by:
jerem81

CPU temperature is too high in Solaris 10 sun fire v890 machine

Hi,
I just installed Solaris 10 on a sun fire v890 machine. I used the prtdiag -v command to check the system.
However, It appears to me that the CPU temperatures is higher than the temperature range specified in the technical specification. The server is a standalone node that does not connect to the network or process anything.
Is it a problem? Thank you.
========================= Environmental Status =========================
System Temperatures (Celsius):
Device Temperature Status
CPU0 77 OK
CPU1 76 OK
CPU2 77 OK
CPU3 74 OK
MB 28 OK
IOB 24 OK
DBP0 23 OK
Environmental
AC power      200-240 VAC, 47-63 Hz, 2078 VA
Operating temperature
* 5� C to 35� C (41� F to 95� F), 20% to 80% relative humidity, non condensing, 27� C max. wet bulb
* 2.1 GHz UltraSPARC IV+ processor: ASHRAE Class 3 (35C/900m) and/or 28C/10kft
Non operating temperature      -20� C to 60� C (-4� F to 140� F), 95% at 40� C relative humidity, non condensing
Regards,
Ryan

Hi Rukbat,
Thanks for your reply.
I have displayed the verbose prtdiag -v on the v890 machine.
However, I couldn't find the hard-coded operational ranges. Could you please advise?
Hi Sun-worshiper,
I executed the command and couldn't find the targeted temperature.
bash-3.00# prtpicl -v -c temperature-sensor | more
CPU0_DIE_TEMPERATURE_SENSOR (temperature-sensor, 8d00000e17)
:PSVC_FRU (8d00001ec9TBL)
| (8d0000124bH) |
:PSVC_PHYSICAL_DEVICE (8d00001da6TBL)
| (8d00001278H) |
:PSVC_PARENT (8d00001867TBL)
| (8d00000dadH) |
:PSVC_TS_OVERTEMP_LED (8d00001649TBL)
| (8d0000101aH) | (8d00000de3H) |
:HighShutdownThreshold 105
:HighWarningThreshold 100
:LowShutdownThreshold -15
:LowWarningThreshold -10
:Temperature 52
:FaultInformation NO_FAULT
:State OK
:_class temperature-sensor
:name CPU0_DIE_TEMPERATURE_SENSOR
CPU2_DIE_TEMPERATURE_SENSOR (temperature-sensor, 8d00000e35)
:PSVC_FRU (8d00001ed2TBL)
| (8d0000124bH) |
:PSVC_PHYSICAL_DEVICE (8d00001dafTBL)
| (8d00001287H) |
:PSVC_PARENT (8d00001870TBL)
| (8d00000dadH) |
:PSVC_TS_OVERTEMP_LED (8d00001655TBL)
| (8d0000101aH) | (8d00000de3H) |
:HighShutdownThreshold 105
:HighWarningThreshold 100
:LowShutdownThreshold -15
:LowWarningThreshold -10
:Temperature 52
:FaultInformation NO_FAULT
:State OK
:_class temperature-sensor
:name CPU2_DIE_TEMPERATURE_SENSOR
MB_AMB_TEMPERATURE_SENSOR (temperature-sensor, 8d00000e8f)
:PSVC_FRU (8d00001ef6TBL)
| (8d0000125aH) |
:PSVC_PHYSICAL_DEVICE (8d00001dcaTBL)
| (8d000012f0H) |
:PSVC_PARENT (8d0000188bTBL)
| (8d00000b34H) |
:PSVC_TS_OVERTEMP_LED (8d00001679TBL)
| (8d0000101aH) |
:HighShutdownThreshold 75
:HighWarningThreshold 70
:LowShutdownThreshold -15
:LowWarningThreshold -10
:Temperature 28
:FaultInformation NO_FAULT
:State OK
:_class temperature-sensor
:name MB_AMB_TEMPERATURE_SENSOR
IOB_AMB_TEMPERATURE_SENSOR (temperature-sensor, 8d00000e99)
:PSVC_FRU (8d00001eedTBL)
| (8d0000125fH) |
:PSVC_PHYSICAL_DEVICE (8d00001dcdTBL)
| (8d000012f0H) |
:PSVC_PARENT (8d0000188eTBL)
| (8d00000b34H) |
:PSVC_TS_OVERTEMP_LED (8d0000167cTBL)
| (8d00001014H) |
:HighShutdownThreshold 53
:HighWarningThreshold 48
:LowShutdownThreshold -15
:LowWarningThreshold -10
:Temperature 25
:FaultInformation NO_FAULT
:State OK
:_class temperature-sensor
:name IOB_AMB_TEMPERATURE_SENSOR
DBP0_AMB_TEMPERATURE_SENSOR (temperature-sensor, 8d00000ed9)
:PSVC_FRU (8d00001ef0TBL)
| (8d00001322H) |
:PSVC_PHYSICAL_DEVICE (8d00001dd0TBL)
| (8d00001304H) |
:PSVC_PARENT (8d000018afTBL)
| (8d00000eadH) |
:PSVC_TS_OVERTEMP_LED (8d0000167fTBL)
| (8d00001014H) |
:HighShutdownThreshold 55
:HighWarningThreshold 51
:LowShutdownThreshold -15
:LowWarningThreshold -10
:Temperature 26
:FaultInformation NO_FAULT
:State OK
:_class temperature-sensor
:name DBP0_AMB_TEMPERATURE_SENSOR
Regards,
Ryan
Edited by: puikeong on Mar 5, 2008 6:45 PM
Edited by: puikeong on Mar 5, 2008 6:47 PM

Solaris 8 on a Sun Fire v480 (full vs half duplex)

Similar Messages

Maybe you are looking for