Solaris 8 USB storage (2 tb)...can't mount

Hello all,
I have been trying for the past week to mount a 2 TB usb storage device that I built. It shows up when I type
cd /dev/rdsk
ls -l c*0 | grep usb
I then tried to mount it with this command (vold turned off)
mount -F pcfs /dev/dsk/c4t0d0s0:c /mnt
it says no device or address.....
so I typed iostat -En
got this
usb_sd1 Soft Errors: 3 Hard Errors: 0 Transport Errors: 0
Vendor: Product: Combine 4HDD0702 Revision: 1278 Serial No:
Size: 2000.43GB <2000431448064 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 3 Predictive Failure Analysis: 0
I need HELP!!!
Thanks
Kluesy

Hello! First try using the motherboard ports to rule out a bad pci card. Then attache the drive and turn it on and open disk utility to see if it can repair it. If that doesn't work boot from the install cd and run disk utility from there to try and repair the drive. It has been formatted hasn't it? Tom

Similar Messages

Can't Mount External SCSI to USB Drive

Hi guys- I currently have a problem involving an external scsi to usb drive that I can't mount. I tried the usual commands, fdisk -l, mount, lsblk, to discover the device but it's not showing up in /dev.
I ran lsusb -v and one section shows "mass storage" and since I don't have any other mass storage devices attached other than my /dev/sda, my guess is that this is the device. Below is the output of lsusb -v, how can I use this info to get this device mounted?
Bus 001 Device 008: ID 03e0:6830
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x03e0
idProduct 0x6830
bcdDevice 0.01
iManufacturer 56
iProduct 63
iSerial 76
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval

alphaniner wrote:This isn't the first time I've read of a device working with some other distro but not with arch. Barring hardware that's on its last legs or has poorly designed firmware, I guess it must be a software issue. What software though? kernel? usb libraries? I dunno.
I'm using the latest kernel. The device is a macally Hi-Speed USB 2.0 external drive enclosure. Yesterday my BIOS was detecting it, and later that night I actually mounted the device with mount /dev/sdb1 /mnt/drive_2, I fired up the computer today and it's not there anymore, not in BIOS, not in the OS. This thing is acting very buggy and It's starting to scream hardware issues. There is a blue light on the enclusure that tells you when everything is okay, but now the light is red. Plus I can't hear the drive spinning.
arobson- I tried your suggestion and ran udevil monitor and a message popped up "Monitoring activity from the disks daemon. Press Ctrl+C to cancel." Then I plugged in the drive but I'm not sure what's supposed ot happen. I didn't get any messages after that.
Sorry to waste your time on this one guys.

USB storage devices not being recognised

Product:
13" Macbook Pro w/ Retina Display (Late 2013 model)
OS X Yosemite (version 10.10.2)
2.4GHz i5, 8gb 1600 MHz DDR3, 256gb HDD
Issue:
- macbook unable to recognise USB storage devices.
- can be found on disk utility but 'greyed out'.
- cannot be found under devices in finder.
- tried restarting laptop, no effect.
- additional storage via Nifty + 64gb micro SD is working fine.
- apple products (iPod/iPhone/iPad) and printer/scanner working fine, only storage devices appear to be affected.
- USB-ethernet adapter appears to be working w/o problems too.
- last technical thing done to the computer was SMC reset 5 days ago for power cable light not working properly (fixed with reset).
Hello everyone,
I seem to having some issues with my macbook and the ability to use USB storage devices. The SD card slot appears to be working fine as I have a nifty device attached on. I'm not sure exactly when this started to happen but it was working last week for sure.
I've put some succinct notes above for anyone who is willing to help out and is able to use it to determine the problem but I don't think it's a hardware issue. Maybe it's a bug with the new OS X update over the weekend?
I've attached a screenshot of the disk utility below as well.
If anyone could help me out then that would be greatly appreciated.
Thanks in advance!

Some users on another Apple thread had success in running Kext Utility last November with similar issues.
I ran kext utility 2.6.1, restarted my computer and everything was working again.

Macbook 2012 Mid: Can't mount USB mass storage after upgrading to Mavericks

Hi guys,
I'm having big problems with USB mass storages. After upgrading to Mavericks my Mac doesn't see some USB storage devices (mostly USB sticks and Android phone's memory cards via USB. My external USB 3.0 hard disks work fine) at all even though the devices themselves (for example my Android phone) are clearly recognized according to the System Report. When I plug them in, they don't show up on my Finder or on Disk Utility.
I've searched everywhere and it seems like some other people are having the same problem, none seems to offer a definite solution. I've even formatted my HD and reinstalled Mavericks from the recovery partition. Now it mounts a USB stick that was in one of the USB ports at the time of installation but still doesn't read anything else! The funny thing is when I boot into Windows 8 on my Boot Camp partition, I can mount any USB devices including the USB stick and the Android phone I'm having problems on Mavericks without any problems. I can even see then when I boot into the recovery so there's clearly something wrong with Mavericks.
Any chance someone has figured out a solution for this? Apple should've address this long time ago.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem? Note: If the devices are not in Mac OS X format, they normally won't mount in safe mode, but they should appear in Disk Utility.
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Mount foreign usb storage

The aim is to mount any usb storage (say, not mine one) with write rights for normal user. So, use cases with fstab and udev automounting are not acceptable.
OK, I have found this https://wiki.archlinux.org/index.php/US … ge_Devices wiki page and have tried to follow. In particular, I have:
~ $ sudo blkid -o list -c /dev/null | grep sdc1
/dev/sdc1 ext4 (not mounted) 15bfa2da-6214-4228-851e-c1207b74fc34
~ $ sudo mount -o gid=users,fmask=113,dmask=002 /dev/sdc1 /media
mount: wrong fs type, bad option, bad superblock on /dev/sdc1,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
dmesg shows "Unrecognized mount option" for all these three options (I have tried to remove them one by one). Apparently, ext4 just hasn't these options. But - how to mount?

Congratulations on your choice of Os ;-)
To solve this problem you can try and create a directory called /rmdisk , then start vold running:
/etc/init.d/volmgt stop
/etc/init.d/volmgt start
if you are lucky your USB flash will show up under /rmdisk/<name> after a few seconds.
If not you should be able to see the flash with cfgadm, which list the status of USB ports (among other things).
Solaris should automatically create a /dev/dsk/ and /dev/rdsk/ entries for your flash memory, if its not automatically mounted by vold, try and stop vold using
/etc/init.d/volmgt stop
Then do a cd /dev/dsk and run an ls -lart, the USB devices should be among the last devices in that list, then mount it using:
mount -F pcfs /dev/dsk/<device> /some/directory
the device should end with s2 or p2, some flash devices might also need :c, aka /dev/dsk/<device>:c, it depends how its configured.
See man mount_pcfs for more information...
Hope this helps a bit (:
//Magnus

MOUNT USB STORAGE FOR VM BACKUP

Hi, I just tried to mount USB Storage to my host with linux version.
I detect it with fdisk -l and esxcli storage core device list | grep -i usb, after stopping usbarbitrator
Result:
/dev/disks #dmesg
ScsiDevice: 3385: Successfully registered device "mpx.vmhba50:C0:T0:L0" from plugin "NMP" of type 0
/dev/disks # esxcli storage core device list | grep -i usb
Display Name: Local USB Direct-Access (mpx.vmhba32:C0:T0:L0)
Display Name: Local USB Direct-Access (mpx.vmhba50:C0:T0:L0)
How can I get disk usable for perform a VM backup?

hooya wrote:
It's in debugging mode now, which is why I can adb push to the phone. The phone should (and has in the past) mounted USB storage even in debugging mode.
That wouldn't change the fact that no other USB mass storage will mount either. I'm just using my phone as an example. USB Hard drives and my SD card reader don't show up either, but I can't do a "push" command to those like I can my phone...
If you are wondering where your post went, I think you meant to hit the 'reply' link rather than the 'report' link. It happens more often than you would think
Edit: Oh, I see you already figured that out.
Last edited by ewaller (2012-07-06 02:30:26)

Upload to Usb-Storage is very fast, that's why i can't umount!

Hi everyon
If i upload some stuff to an usb-storage it's like its uploading very very fast, like 100mb in 1 second, but in background it's still uploading(i can't umount). The problem is every program is showing me that the stuff is uploaded in 1-2 second. I have to wait everytime, but i don't know how long, and that's really annoying.
How can i fix it ?
/etc/fstab
/dev/sdb /media/sdb vfat rw,users,umask=000,uid=fatih 0 0
dmesg
usb 1-1: USB disconnect, address 4
usb 1-1: new full speed USB device using uhci_hcd and address 5
usb 1-1: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi 5:0:0:0: Direct-Access Nokia N95 1.0 PQ: 0 ANSI: 0
sd 5:0:0:0: [sdb] 1000215 512-byte hardware sectors (512 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sd 5:0:0:0: [sdb] 1000215 512-byte hardware sectors (512 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sdb: unknown partition table
sd 5:0:0:0: [sdb] Attached SCSI removable disk
sd 5:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
usb 1-1: USB disconnect, address 5
NOTE: I've tried it on Ubuntu, and there wasn't any problem.

But i don't know how long i have to wait.
Well, thats kind of the thing... It could be forever. The kernel/filesystem might decide to halt copying until you decide to sync _or_ add more files, so it can make all the pieces in the puzzle (partition) fit without defragmentation. See?
If you decide to mount with sync, you get a steady stream transfer to your device, and you will theoretically see how long the task will take. (am i mistaken?)
If you decide to go with nosync (default behaviour), this is not possible. But the benefit would be less defragmentation.
I guess that i would be possible to have the system tell you how long the actual "sync" manouver will take when you unmount, but as far as i know this is not implemented yet. Maybe you could file a feature request somewhere? (i dont know if the HAL scripts or notification-daemon is reponsible for the actual "information" you recieve)

How can I see file with chinese name in Sunray USB storage?

hi, All
I installed Sunray4u3 on Solaris0805. the application server is win2003EE.
I accessed usb storage from win2003, but I can only see files with English name , and could not see files with chinese name. Why? who can help?
best regards
xiong wei

You might want to make sure your credit card is listed in the billing information associated with your Apple ID (see http://support.apple.com/kb/ht1918).
Also, to change the From name that appears when you address emails on and iOS device, go to Settings>Mail,Contacts,Calendars...tap your iCloud email account, tap you iCloud account at the top, tap Mail at the bottom, then enter the name you want to use in the Name field at the top.
To change the From name on your Mac Mail, go to icloud.com, sign into your account, open Mail, click the gear shaped icon on the bottom left and choose Preferences, go to the Accounts tab and enter the name you want to use in the Full Name field and click Done. Then quit Mail on your Mac and re-open it. Your new From name should now appear in the drop-down list when you compose a new email.

Aperture can't empty Trash on USB storage (permissions)

Problem:
- Aperture 3.6 cannot delete referenced files located on external USB storage directly attached to my MacBook Pro with Yosemity.
- When I try to empty Trash in Aperture, I get "You don’t have access to the System Trash on the original files’ volume."
The drive is NTFS formatted 4Tb in RAID-1 (Raidon's GR3630-SB3 model).
I have Paragon's "NTFS for Mac OS" installed on my MacBook which works fine and Access Permissions enabled.
At the same time, I tested my 64Gb USB flash drive with NTFS and it worked FINE!
I played with permissions using 3rd party apps like BatChmod. No luck.
I googled and searched this Forum.
People had similar problems with NAS (networked) storage, though if a storage is directly attached, they say it should work as designed.
One solution is a script, though it skipped some of the referenced files - unpredictable results and risks to the master's library.
Any idea how to fix this drive or Aperture issue?
Thanks.

I can't confirm now if drive's trashes can be seen in the main Mac Trash. It's busy replicating RAID1 now. I will check later.
That is your next step. Post back when you can test it.
However as noted, this will always be problematic and if reformatting the drive for OS X is not possible then I'd strongly suggest you get a drive to store your referenced originals on. Given the price of disk, just got 2tb for $80 US at newegg this would seem to be your best option.
regards

Since I have upgraded to mountain lion hhd cannot be mounted to my iMac. Either usb drives. What can I do?

After upgrading to mountail lion my imac can not mount hdd's or usb flash drives. What should I do?

Try this: in your Utilities folder launch Adobe Flash Player Install Manager and run it to completely uninstall Flash. Then go to http://get.adobe.com/flashplayer/ and download Flash
Once downloaded, double-click to open it and run the installer. If you get a message saying the file can't be opened, or similar, Control+click or right click and select 'open' and should then be able to proceed to install it.

Can't mount Solaris 10 DVD

I've been having trouble mounting the Solaris 10 10/08 Operating System SPARC DVD after installation so that I can add packages from the DVD. Rather than burn my own DVDs, I bought the media kit. Booting from that DVD in order to install Solaris 10 on this Sun Blade 150 workstation was successful, but it should now automatically mount when I insert it. This is using the internal DVD ROM drive that came with the workstation.
I can mount the other DVDs in the kit.
I can mount the problem DVD on Windows Vista, but that environment messes with the file names while creating a ZIP file so that by the time the package gets to the workstation where it's needed, it's useless.
Next, I bought an external DVD ROM drive and got the same results on my workstation.
I then moved the external DVD ROM drive to my Sun Fire V210 server and got the same results.
Finally, I asked the fine folks at Sun to send me a replacement DVD. They sent the whole kit. The results are exactly the same on the workstation with the internal DVD ROM drive. I can't mount the SPARC DVD, but I can mount the x86 DVD for example.
I previously attempted to burn the DVDs using the only drive I own that is supposed to have that capability, an internal drive on the Windows Vista PC. That failed.
This should work using the media kit that I bought. What's the solution?
Alan M. Feldstein
[Cosmic Horizon|http://www.alanfeldstein.com/]

Sun-worshiper wrote:
Have you encountered the following bug:
[http://bugs.opensolaris.org/view_bug.do?bug_id=6712352]
(found on this thread: [http://forums.sun.com/thread.jspa?threadID=5347812&tstart=0])
It is as jluband1 described in that thread, but only for the SPARC version of the Solaris 10 Update 6 DVD. The workaround communicated by maureen12345 is successful:
# svcadm disable -t volfs
# mount -F hsfs /dev/dsk/c0t1d0s0 /mnt
# ls -l /mnt
total 929
drwxr-xr-x   2 root     root        2048 Oct 27 14:21 boot
-r--r--r--   1 root     root        6557 Jul 31 2008 Copyright
-rwxr-xr-x   1 root     root         257 Oct 27 13:57 installer
-r--r--r--   1 root     root      460262 Jul 31 2008 JDS-THIRDPARTYLICENSEREADME
drwxr-xr-x   2 root     bin         2048 Oct 27 14:20 License
drwxr-xr-x   5 root     root        2048 Oct 27 14:21 platform
drwxr-xr-x   7 root     root        2048 Oct 27 14:21 Solaris_10
# (I always search the forum before posting, but didn't originally find the thread you reference, perhaps because "DVD" didn't appear in the subject.)

Can't mount 3rd party DAS storage and Xsan volume simutaneously

Xsan client(MacPro) equipped an Apple FC HBA card can't mount SGI TP9300 DAS storage and Xsan volume simutaneously when powering on or restarting.
Among 2 FC ports, one port is used for Xsan volume using Xserve RAID, and the other port is used for SGI TP9300 storage which is directly connected to that Mac.
When booting, Xsan volume is always mounted normally, but SGI TP9300 volume is not.
Sometimes TP9300 volume is mounted about 20~30 minutes later.(I attached system.log file)
The LUN of TP9300 is seen at Disk Utility, so it's not physical problem.
It seems that actual volume information is not correctly processed at booting time.
While, after booting the system with the FC cable for TP9300 disconnected and confirming that Xsan volume mounted normally, then connecting the FC cable for TP9300, the TP9300 volume is mounted immediately.
Mac OS X 10.4.8, Xsan 1.4 is being used.

Yes, I think you screwed your xsan volume. You can not remove luns from pools, and you can not remove volumes from volumes.
How important is your existing data? In your case I would concentrate on that. This is not trivial. Theorotically you have lost your data allready. In practise you might have luck.
Once I was in your kind of twilight zone, and managed to keep the data. It is a complete cli job. You have to be very carefull about with your config files. You could hire an experienced xsan consultant. If that is not possible, read the manpages very carefully before doing anything on the volume.
Regards
Donald

[Solved] Can't mount specific usb device after kernel upgrade

So, hi everyone
I've got a usb device which works on other systems (usb audio player, android tablet) but not on my archlinux htpc.
System is up to date, the usb stick worked a few days ago (here shown as /dev/sdc), relevant infos (shortened):
$ uname -a
Linux arch247 3.10.3-1-ARCH #1 SMP PREEMPT Fri Jul 26 11:26:59 CEST 2013 x86_64 GNU/Linux
$ lsusb
Bus 009 Device 006: ID 090c:1000 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) Flash Drive
$ dmesg
[ 1788.621747] usb 9-4: new full-speed USB device number 8 using ohci_hcd
[ 1788.771370] usb 9-4: not running at top speed; connect to a high speed hub
[ 1788.785511] usb-storage 9-4:1.0: USB Mass Storage device detected
[ 1788.793170] scsi13 : usb-storage 9-4:1.0
[ 1789.801391] scsi 13:0:0:0: Direct-Access General USB Flash Disk 1.00 PQ: 0 ANSI: 2
[ 1789.814964] sd 13:0:0:0: [sdc] 15669248 512-byte logical blocks: (8.02 GB/7.47 GiB)
[ 1789.819230] sd 13:0:0:0: [sdc] Write Protect is off
[ 1789.819243] sd 13:0:0:0: [sdc] Mode Sense: 03 00 00 00
[ 1789.825267] sd 13:0:0:0: [sdc] No Caching mode page present
[ 1789.825281] sd 13:0:0:0: [sdc] Assuming drive cache: write through
$ lsmod | grep ohci
ohci_hcd 26544 0
usbcore 176991 6 ath3k,btusb,usb_storage,ohci_hcd,usbhid,xhci_hcd
$ sudo fdisk -l
Disk /dev/sda: 120.0 GB, 120034123776 bytes, 234441648 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: dos
Disk identifier: 0x89675d3a
Device Boot Start End Blocks Id System
/dev/sda1 2048 50333695 25165824 83 Linux
/dev/sda2 50333696 234441647 92053976 83 Linux
Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes, 3907029168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: dos
Disk identifier: 0x0004e72c
Device Boot Start End Blocks Id System
/dev/sdb1 2048 3907022847 1953510400 83 Linux
Disk /dev/sdc: 8022 MB, 8022654976 bytes, 15669248 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: dos
Disk identifier: 0x0009ae2c
Device Boot Start End Blocks Id System
/dev/sdc1 2048 15669247 7833600 c W95 FAT32 (LBA)
I can't reformat the device at the moment (lack of computers here). The usb port on the pc is working (tested with another fat32 formatted usb stick).
Any ideas? Hints? Tips?
Last edited by D4ve (2013-08-18 18:48:35)

It works on 3.9.11.
dmesg on 3.9.11:
[ 74.391651] usb 3-4: new high-speed USB device number 3 using xhci_hcd
[ 74.410514] usb 3-4: New USB device found, idVendor=0951, idProduct=1607
[ 74.410529] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 74.410532] usb 3-4: Product: DataTraveler 2.0
[ 74.410534] usb 3-4: Manufacturer: Kingston
[ 74.410536] usb 3-4: SerialNumber: 00137299803FA931262A00CD
[ 74.465400] Initializing USB Mass Storage driver...
[ 74.465654] scsi7 : usb-storage 3-4:1.0
[ 74.465726] usbcore: registered new interface driver usb-storage
[ 74.465728] USB Mass Storage support registered.
[ 75.465448] scsi 7:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 75.465839] sd 7:0:0:0: Attached scsi generic sg4 type 0
[ 75.466277] sd 7:0:0:0: [sdd] 3973120 512-byte logical blocks: (2.03 GB/1.89 GiB)
[ 75.466620] sd 7:0:0:0: [sdd] Write Protect is off
[ 75.466625] sd 7:0:0:0: [sdd] Mode Sense: 23 00 00 00
[ 75.466955] sd 7:0:0:0: [sdd] No Caching mode page present
[ 75.466960] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[ 75.469081] sd 7:0:0:0: [sdd] No Caching mode page present
[ 75.469087] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[ 75.681901] sdd: sdd1 sdd2
[ 75.683219] sd 7:0:0:0: [sdd] No Caching mode page present
[ 75.683224] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[ 75.683227] sd 7:0:0:0: [sdd] Attached SCSI removable disk
dmesg on 3.10.5:
[ 1370.659092] usb 3-4: new high-speed USB device number 8 using xhci_hcd
[ 1370.677899] usb 3-4: New USB device found, idVendor=0951, idProduct=1607
[ 1370.677906] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1370.677910] usb 3-4: Product: DataTraveler 2.0
[ 1370.677913] usb 3-4: Manufacturer: Kingston
[ 1370.677916] usb 3-4: SerialNumber: 00137299803FA931262A00CD
[ 1370.678442] usb-storage 3-4:1.0: USB Mass Storage device detected
[ 1370.678711] scsi12 : usb-storage 3-4:1.0
[ 1371.674797] scsi 12:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 1371.675283] sd 12:0:0:0: Attached scsi generic sg4 type 0
[ 1371.675809] sd 12:0:0:0: [sdd] 3973120 512-byte logical blocks: (2.03 GB/1.89 GiB)
[ 1371.676184] sd 12:0:0:0: [sdd] Write Protect is off
[ 1371.676192] sd 12:0:0:0: [sdd] Mode Sense: 23 00 00 00
[ 1371.676560] sd 12:0:0:0: [sdd] No Caching mode page present
[ 1371.676567] sd 12:0:0:0: [sdd] Assuming drive cache: write through
[ 1402.372357] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1402.389648] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1402.389655] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1433.410334] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1433.427691] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1433.427698] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1464.352379] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1464.369587] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1464.369592] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1495.294439] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1495.311616] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1495.311623] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1495.314661] sd 12:0:0:0: [sdd] No Caching mode page present
[ 1495.314677] sd 12:0:0:0: [sdd] Assuming drive cache: write through
[ 1526.236340] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1526.253657] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1526.253665] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1557.306368] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1557.323619] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1557.323627] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1588.248358] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1588.265745] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1588.265752] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1619.190405] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1619.207780] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1619.207788] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1619.421206] sdd: sdd1 sdd2
[ 1619.422735] sd 12:0:0:0: [sdd] No Caching mode page present
[ 1619.422741] sd 12:0:0:0: [sdd] Assuming drive cache: write through
[ 1650.132306] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1650.149607] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1650.149614] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1681.202196] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1681.219363] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1681.219370] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1712.144197] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1712.161474] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1712.161482] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1743.086261] usb 3-4: reset high-speed USB device number 8 using xhci_hcd
[ 1743.103565] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ecdc0
[ 1743.103572] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024d4ece00
[ 1743.104256] sd 12:0:0:0: [sdd] Attached SCSI removable disk
EDIT: Doesn't work on 3.11-rc4 either.
Last edited by gmesalazar (2013-08-06 01:30:00)

I have a router that has a readyshare USB storage access port that has mp4's of movies. So how can I view them from my iPad 2 ?

I have a router that has a readyshare USB storage access port that has mp4's of movies. So how can I view them from my iPad 2 ?

I just bought a NETGEAR WNDR3400v2".
I own a mac, running 10.7 and an ipad 1.
I can access my USB stick, on the netgear wireless router, from my mac or ipad.
From a mac or ipad .... http://readyshare.routerlogin.net/shares/USB_Storage/ or just http://readyshare.routerlogin.net/shares
Also, on a mac only, try, go > connect to server> smb://readyshare
Works for me!

How can I back up my local folders (copying/saving them in USB storage)?

I would like to back up just my local folders in Thunderbird; i.e., copy them to a USB storage device?
Is there a way that I can do this?

use the ImportExporttool.
* Install this addon tool: https://freeshell.de//~kaosmos/mboximport-en.html
Use the link and scroll down to bottom to see download.
Save the xpi file to your desktop
* In Thunderbird, 'Tools' > 'Add-ons'
* Add-ons Manager opens in new tab
* click on the daisy wheel icon and select 'Install addon from file'
* locate the saved .xpi file and click on 'open'
* close and restart Thunderbird
Now use the tool to Export the folder or emails in the folder.
* Right click on folder > ImportExport tool >
select from options available such as:
* you could 'export all messages in the folder' as 'eml' format
See image.

Solaris 8 USB storage (2 tb)...can't mount

Similar Messages

Maybe you are looking for