Solaris 9 on Dell Power Edge 6650 x86 system
Does anyone have driver for PERC3 controller for Solaris 9, which comes with Dell Power Edge 6650?? We are tring to install Solaris 9 on Dell Power Edge 6650. The error we get is "No Hard Disks Fount".
Thank U!
After thrashing for 2 weeks with the onboard 7880 SCSI and onboard 7890 RAID controllers, I was finally able to load up Solaris 8 on a Poweredge 2400. (4/01 build)
The only way I was able to do it was configure the server as below:
7880 SCSI: CD-ROM drive only device on this controller, set to ID 5.
7890 RAID controller: Disabled. Dont' believe Dell or Adaptec, this card will not work with Solaris 7 or 8. Even with the RAID chip removed and running as standard SCSI controller, it still would not work.
Adaptec 2940 U2W: 9G Quantum Atlas V drive with HP SureStore DAT 24i drive.
PERC II RAID controller yanked out of older 4100 system, 3 drives running RAID 5.
Important note: Do not attach anything to the 7880 controller besides the CD. The system will not boot if attempting to boot to the HD or if you attempt to boot from CD, it will hang at the adp.bef file.
Hope this helps..
Mike
Similar Messages
-
Solaris 8 on Dell Power Edge 4400
What does it take to get Solaris 8 installed on a Dell Power Edge 4400?
Thus far, I have followed instructions found elsewhere to grab the Adaptec
cadp160 driver, which I successfully install in the Device Configuration Assistant. Every time I select the CD as my boot device, the system wedges while trying to load adp.bef, with a "short read" error. Eventually, the system fails out to the boot interpreter.
This system has 2x1Ghz P4's on it, onboard AIC-7899 (where a Quantum Atlas V lives) and AIC-7880 SCSI controllers, plus a PCI AHA 2940 controller (on which the CD lives).
This is very frustrating--I couldn't install Solaris 8 on my Dell Dimension 4100 either (ACPI tables not in reclaim memory bug).
I am using the Solaris 8 01/01 boot images, FYI.
Has anyone out there successfully gotten Solaris 8 to install and boot on one of these beasts?
Thanks,
ChrisAfter thrashing for 2 weeks with the onboard 7880 SCSI and onboard 7890 RAID controllers, I was finally able to load up Solaris 8 on a Poweredge 2400. (4/01 build)
The only way I was able to do it was configure the server as below:
7880 SCSI: CD-ROM drive only device on this controller, set to ID 5.
7890 RAID controller: Disabled. Dont' believe Dell or Adaptec, this card will not work with Solaris 7 or 8. Even with the RAID chip removed and running as standard SCSI controller, it still would not work.
Adaptec 2940 U2W: 9G Quantum Atlas V drive with HP SureStore DAT 24i drive.
PERC II RAID controller yanked out of older 4100 system, 3 drives running RAID 5.
Important note: Do not attach anything to the 7880 controller besides the CD. The system will not boot if attempting to boot to the HD or if you attempt to boot from CD, it will hang at the adp.bef file.
Hope this helps..
Mike -
Dell Power Edge 6400 CDROM Problem
When installing Solaris 8 for intel in a Dell Power Edge 6400 with two processors, everything looks fine at the begginning before booting, I mean the Cd rom drive is detected as booteable, but when the system start to install, it asks from where to extract the operating system and in the list does not appear the CD Rom, it just displays the networks cards.
Please I have more than a week with this problem, I already check the HCL, I already changed the HD, the CdRom (twice), but it continues without detecting the cdrom after booting.
The Cdrom is in the scsi 5.
Any body in UK, USA, Mexico or wherever please HELP.
Carlos HerreraIf I remember right the Dell Power Edge had an adaptec 160 controller which
you have to download and install the scsi drivers from the Adaptec website.
Check and verify which scsi controller you have on your Dell.
---Bob -
Which free linux can I use on a Dell Power Edge Server 2650
Dear all,
I have recently joined the subscription program and want to install Netweaver. From my old company I could purchase a couple of Dell Power Edge Servers 2650 with 6GB RAM, Dual Core etc - so plenty of hardware. As next step I want to install a linux OS to be able to to install SAP trial version and/or the Netweaver software from the subscription program.
In the compatibility section I have read that I need either SUSE or RedHat linux enterprise edition. But these enterprise editions cost money when purchasing it. Is there also a free linux edition that I could use? If not, which enterprise linux would be the cheapest that I could use?
Thanks and best regards
Daniel BlaschkowskiHi Daniel,
you can download a copy of the installation DVD of SUSE Enterprise Server 10SP2 for free from the Novell's Web Site. You won't have support nor will you be able to get software updates but it will allow you to get a first feeling about Netweaver on Linux.
Another option is to use [Centos |www.centos.org] that is a clone of Redhat Enterprise Server. You will have to cheat a little bit to be able to install SAP on it (you have to make your Centos appear like it is a true Redhat) but it works without a hitch.
Of course, do not run any production instances on such setups as you will get into trouble with SAP support in case you open up a problem message related to these platforms
Have fun,
Seb -
Installation of windows server 2008r2 on dell power edge 2850
I just received an dell power edge 2850, can I install windows server 2008r2 on this unit
Hi rpalmer,
To avoid some potential issues ,It is recommended to contact to DELL for further assistance . Although someone can install 2008R2 on PE 2850 .
http://en.community.dell.com/
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Installation problems (Solaris 10 3/05 release, on x86 system)
Late last year, i recieved a Solaris 10 installation DVD case, containing the intallation DVDs for SPARC and x86 systems.
after finally getting another hard drive (the other was too full), i tried booting the computer off the x86 disc, to install.
it went to the light grey screen where it asks for installation mode, i chose default interactive installation (option 1).
this is where the problem starts. It appears that before beginning the interactive installer, it gathers information about the computer (such as USB ports, 100mb/s connection, etc)
I have read this process should only take a few seconds.
BUT, after 2 hours, it appears to have locked up after displaying "Skipping RTSL 0"
(it may not be rtsl, but something similar, and it was after detecting the 100mb/s connection)
My question is: how do i get it to work so i can install Solaris, without having to wait those 2 hours that should only be a few seconds?
thx to those who answer, thanx
(ps: i have had no previous experience with solaris)errm...
I do not know what TRS-80, VIC-20, or E10K mean, but i can try give you the hardware config (ps i'm installing solaris as a secondary OS in another
partition to XP, on the second HD (so there are 2 Hard drives in the computer).
WARNING: LIST VERY LONG AND POSSIBLY NOT WHAT YOU MEANT FOR ME TO POST (well.. i dont really know how to get HW configs, and what ones you require)
Omega technology ATX
Intel Celeron CPU 1.30 GHz, 512 MB RAM
From XP device manager:
Computer:
ACPI PC
Disk Drives:
ST340810A (partitioned into: C, F, G, and X which will be removed for C soon)
MDT MD400AB-00BVA0 (partitioned into D, and E)
the MDT is the new HD, and partition D will be used for solaris OS and extra space for stuff done in solaris).
Display adapters:
RADEON 9550
RADEON 9550 secondary
DVD/CD-ROM drives:
LG DVD-rom DRD8160B
Lite-on DVDRW SOHW-1673s
Standard floppy disk drive and controller
IDE ATA/ATAPI controllers:
Primary IDE Channel
Secondary IDE Channel
VIA bus master IDE controller
Easy internet keyboard
PS/2 mouse
soft V92 smart speakerphone modem
Monitors: LG 900B
Network adapters:
Surecom EP-320X-R 100/10/M PCI Adapter
Ports (COM & LPT):
COM 1 & COM2
printer port (LPT1)
Processors:
Intel Celeron CPU 1300MHz
Sound, video and game controllers:
Audio Codecs
Legacy Audio Drivers
Legacy Video Capture Devices
Media control Devices
Standard Game port
Unimodem Half-Duplex Audio Device
VIA AC'97 Audio Controller (WDM)
Video Codecs
System Devices:
ACPI fixed feature button
direct memory access controller
ISAPNP read data port
Microcode Update Device
Microsoft ACPI-compliant system
Microsoft system management BIOS driver
motherboard resources
Numeric data processor
PCI bus
Plug and play software device enumerator
programmable interrupt controller
system board
System CMOS/real time clock
System speaker
system timer
VIA CPU to AGP controller
VIA Tech CPU to PCI bridge
VIA Tech PCI to ISA bridge
VIA Tech power management controller
USB controllers:
NEC PCI to USB open host controller
NEC PCI to USB open host controller
standard enhanced PCI to USB host controller
USB root hub
USB root hub
USB root hub
USB root hub
USB root hub
VIA rev 5 or later USB universal host controller
VIA rev 5 or later USB universal host controller
well.. there we go. i hope thats what you wanted :)
thx for replying though. -
Upgrade windows server 2003 to windows server 2012 in power edge 2950 server
Require help on installing windows server 2012 in dell power edge 2950 server.
I have booted server by windows server 2012 DVD, but its not booting from DVD, Kindly help in installing windows
Is the data will be lost after installing windows 2012?
Do i need to update the drivers and firmwares, if yes please specify the driver and firmwares to update
Current installed drivers
Current OS: windows server 2003
RAID 5, SATA hard disk
BIOS: 2.2.6
BMS: 1.97
RAC: 1.32
PERC/6 = Firmware = 6.0.2
Driver: 2.14
This topic first appeared in the Spiceworks CommunityHi thereCan anybody give me good suggestions for an AV System?
I have to protect 3 Windows DMZ Servers (2 Webservers and 1 Hyper-V Server)What points are important and on what points should I pay attention.I've read some reviews and Kaspersky seems to be a good solution, does anybody already have experience with Kaspersky.And which Kaspersky product should I choose for my case:http://usa.kaspersky.com/store/business-security/?PID=3471305http://www.kaspersky.com/de/business-securityCan I also buy the products form the first link, when I live in another country than in the States.
Greetings -
Problem with solaris 10 08/11 installation on x86 workstation (DELL T5500)
Trying to install solaris 10 08/11 installation on x86 workstation (DELL T5500). Following error message was received after selecting the Oracle Solaris interactive Text (Desktop Session) installation method-
SunOS Release 5.10 Version Generic_147441-01 64-bit
Copyright (c) 1983, 2011, Oracle and/or its affiliates. All rights reserved.
Configuring devices.
SUNW-MSG-ID: SUNOS-8000-0G, TYPE: Error, VER: 1, SEVERITY: Major
EVENT-TIME: 0x5075a820.0x8f97a90 (0x1693e68979)
PLATFORM: i86pc, CSN: -, HOSTNAME:
SOURCE: SunOS, REV: 5.10 Generic_147441-01
DESC: Errors have been detected that require a reboot to ensure system
integrity. See http://www.sun.com/msg/SUNOS-8000-0G for more information.
AUTO-RESPONSE: Solaris will attempt to save and diagnose the error telemetry
IMPACT: The system will sync files, save a crash dump if needed, and reboot
REC-ACTION: Save the error summary below in case telemetry cannot be saved
panic[cpu0]/thread=fffffe80000b3c60: pcieb-7: PCI(-X) Express Fatal Error. (0x4)
fffffe80000b3bf0 pcieb:pcieb_intr_handler+1ea ()
fffffe80000b3c40 unix:av_dispatch_autovect+78 ()
fffffe80000b3c50 unix:intr_thread+5f ()
syncing file systems... done
ereport.io.pci.fabric ena=1693e6221600001 detector=[ version=0 scheme="dev"
device-path="/pci@19,0/pci8086,3410@9" ] bdf=2048 device_id=3410 vendor_id=
8086 rev_id=22 dev_type=40 pcie_off=90 pcix_off=0 aer_off=100 ecc_ver=0
pci_status=10 pci_command=47 pci_bdg_sec_status=0 pci_bdg_ctrl=3 pcie_status=6
pcie_command=7 pcie_dev_cap=8021 pcie_adv_ctl=5 pcie_ue_status=4020
pcie_ue_mask=100000 pcie_ue_sev=62030 pcie_ue_hdr0=0 pcie_ue_hdr1=0
pcie_ue_hdr2=0 pcie_ue_hdr3=0 pcie_ce_status=0 pcie_ce_mask=0
pcie_ue_tgt_trans=0 pcie_ue_tgt_addr=0 pcie_ue_tgt_bdf=ffff pcie_rp_status=0
pcie_rp_control=0 pcie_adv_rp_status=7c pcie_adv_rp_command=7
pcie_adv_rp_ce_src_id=2048 pcie_adv_rp_ue_src_id=2048 remainder=0 severity=44
skipping system dump - no dump device configured
rebooting...
Any ideas?Sometimes, it's just easier and faster
to just start all over and re-install,
particularly when you have only a fresh install on your system.
This time, do not choose to include all the optional "documentation"
(that's what is held on CD5).
I have never found a reason to ever read that documentation so I stopped installing it.
... or you could download and burn a copy of CD5 and use it when prompted. -
Could not mount USB drive on Solaris 10 x86 system
Hi All,
I am having difficulty mounting a USB drive on Solaris 10 x86 system with the following different unsuccessful attempts:
# uname -a
SunOS venus 5.10 Generic_139556-08 i86pc i386 i86pc
# rmformat
Looking for devices...
1. Volmgt Node: /vol/dev/aliases/cdrom0
Logical Node: /dev/rdsk/c0t0d0s2
Physical Node: /pci@0,0/pci-ide@4/ide@0/sd@0,0
Connected Device: TEAC DV-28E-V 1.AC
Device Type: DVD Reader
2. Logical Node: /dev/rdsk/c4t0d0s2
Physical Node: /pci@0,0/pci108e,534b@2,1/storage@9/disk@0,0
Connected Device: WD My Book 1140 1007
Device Type: Removable
3. Volmgt Node: /vol/dev/aliases/rmdisk0
Logical Node: /dev/rdsk/c4t0d0p0
Physical Node: /pci@0,0/pci108e,534b@2,1/storage@9/disk@0,0
Connected Device: WD My Book 1140 1007
Device Type: Removable
# svcs volfs
STATE STIME FMRI
online Apr_13 svc:/system/filesystem/volfs:default# ls -lt /mnt
total 0
# mount -F pcfs /dev/dsk/c4t0d0p0:c /mnt
mount: I/O error
# mount -F pcfs /dev/rdsk/c4t0d0p0:c /mnt
mount: Block device required
# mount -F pcfs /dev/dsk/c4t0d0s2:c /mnt
mount: I/O error
# mount -F pcfs /dev/rdsk/c4t0d0s2:c /mnt
mount: Block device required
# fsck /dev/dsk/c4t0d0p0
Can't open /dev/rdsk/c4t0d0p0: I/O error
# fsck /dev/rdsk/c4t0d0p0
Can't open /dev/rdsk/c4t0d0p0: I/O error
# fsck /dev/dsk/c4t0d0s2
Can't open /dev/rdsk/c4t0d0s2: I/O error
# fsck /dev/rdsk/c4t0d0s2
Can't open /dev/rdsk/c4t0d0s2: I/O errorSecond try,
# svcadm disable volfs
# svcs volfs
STATE STIME FMRI
disabled 20:47:00 svc:/system/filesystem/volfs:default
# mount -F pcfs /dev/dsk/c4t0d0p0:c /mnt
mount: I/O errorLast try,
# mkdir /rmdisk
mkdir: Failed to make directory "/rmdisk"; File exists
# ls -lt /rmdisk
total 4
lrwxrwxrwx 1 root nobody 16 Oct 1 2009 rmdisk0 -> ./unnamed_rmdik
drwxr-xr-x 2 root nobody 512 Sep 30 2009 unnamed_rmdisk
# cd /rmdisk
# ls -lt
total 4
lrwxrwxrwx 1 root nobody 16 Oct 1 2009 rmdisk0 -> ./unnamed_rmdik
drwxr-xr-x 2 root nobody 512 Sep 30 2009 unnamed_rmdisk
# ls -lt unnamed_rmdisk
total 0
# ls -lt rmdisk0
lrwxrwxrwx 1 root nobody 16 Oct 1 2009 rmdisk0 -> ./unnamed_rmdik
# df -h
Filesystem size used avail capacity Mounted on
/dev/dsk/c1t0d0s0 5.1G 4.0G 1.1G 78% /
/devices 0K 0K 0K 0% /devices
ctfs 0K 0K 0K 0% /system/contract
proc 0K 0K 0K 0% /proc
mnttab 0K 0K 0K 0% /etc/mnttab
swap 5.9G 984K 5.9G 1% /etc/svc/volatile
objfs 0K 0K 0K 0% /system/object
sharefs 0K 0K 0K 0% /etc/dfs/sharetab
/usr/lib/libc/libc_hwcap2.so.1
5.1G 4.0G 1.1G 78% /lib/libc.so.1
fd 0K 0K 0K 0% /dev/fd
swap 5.9G 148K 5.9G 1% /tmp
swap 5.9G 32K 5.9G 1% /var/run
/dev/dsk/c1t0d0s7 129G 1.7G 126G 2% /export/home
# /etc/init.d/volmgt stop
# svcs volfs
STATE STIME FMRI
disabled 21:02:31 svc:/system/filesystem/volfs:default
# pwd
/rmdisk
# cd /
# ls -lt /rmdisk
total 4
lrwxrwxrwx 1 root nobody 16 Oct 1 2009 rmdisk0 -> ./unnamed_rmdik
drwxr-xr-x 2 root nobody 512 Sep 30 2009 unnamed_rmdisk
# /etc/init.d/volmgt st
# svcs volfs
STATE STIME FMRI
disabled 21:02:31 svc:/system/filesystem/volfs:default
# /etc/init.d/volmgt start
volume management starting.
# svcs volfs
STATE STIME FMRI
online 21:04:44 svc:/system/filesystem/volfs:default
# svcs volfs
# mount | grep rmdisk
# pwd
# ls -lt /rmdisk
total 4
lrwxrwxrwx 1 root nobody 16 Oct 1 2009 rmdisk0 -> ./unnamed_rmdik
drwxr-xr-x 2 root nobody 512 Sep 30 2009 unnamed_rmdisk
# ls -lt /rmdisk/unnamed_rmdisk
total 0
# iostat -En
c0t0d0 Soft Errors: 3 Hard Errors: 0 Transport Errors: 0
Vendor: TEAC Product: DV-28E-V Revision: 1.AC Serial No:
Size: 0.00GB <0 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 3 Predictive Failure Analysis: 0
c1t0d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: HITACHI Product: HUS1514SBSUN146G Revision: SA04 Serial No: 0921B2Y3PC
Size: 146.81GB <146810535936 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c1t1d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: HITACHI Product: HUS1514SBSUN146G Revision: SA04 Serial No: 0921B2Z5NC
Size: 146.81GB <146810535936 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c4t0d0 Soft Errors: 21 Hard Errors: 0 Transport Errors: 0
Vendor: WD Product: My Book 1140 Revision: 1007 Serial No:
Size: 2000.37GB <2000365289472 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 21 Predictive Failure Analysis: 0
#This is a working production system with 2 146.81GB mirrored hard disks. There is no disk error for either local or external 2TB Western Digital USB disks that works on Windows 7 or XP.
Any idea on what else to look for?
Thanks in advance,
Jack
Edited by: 797805 on 6/06/2012 04:48Hi All,
Looks like it was a driver / incompatibility / unsupported issue since 2 other much smaller USB keys (Lexar USB Flash Drive – 32GB, SanDisk Cruzer Colors – 4GB) were successfully mounted automatically by volfs service as follows:
# df -h
Filesystem size used avail capacity Mounted on
/dev/dsk/c1t0d0s0 5.1G 4.0G 1.1G 78% /
/dev/dsk/c1t0d0s7 129G 1.7G 126G 2% /export/home
/vol/dev/dsk/c3t0d0/unnamed_rmdisk#1:c 3.7G 2.4G 1.3G 65% /rmdisk/unnamed_rmdisk#1
/vol/dev/dsk/c2t0d0/unnamed_rmdisk:c 29G 96K 29G 1% /rmdisk/unnamed_rmdiskIt also appears that the Device status of Not Ready from “iostat –En” below may not be correct either since both smaller drives are working fine:
# iostat -En
c4t0d0 Soft Errors: 23 Hard Errors: 0 Transport Errors: 0
Vendor: WD Product: My Book 1140 Revision: 1007 Serial No:
Size: 2000.37GB <2000365289472 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 23 Predictive Failure Analysis: 0
c2t0d0 Soft Errors: 7 Hard Errors: 0 Transport Errors: 0
Vendor: Lexar Product: USB Flash Drive Revision: 1100 Serial No:
Size: 31.41GB <31406948352 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 7 Predictive Failure Analysis: 0
c3t0d0 Soft Errors: 60 Hard Errors: 8 Transport Errors: 0
Vendor: SanDisk Product: Cruzer Colors+ Revision: 8.02 Serial No:
Size: 4.02GB <4022337024 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 8 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0In other word, the same question remains on whether it is possible to install a driver to overcome this issue and where to such driver?
It is necessary to install additional driver that came with the disk on Windows XP platform. However,
Thanks again,
Jack -
I am trying to install OS (Red hat 6.0) in Dell 1950 power-edge III gen, After booting CD i got option to hit F1 to install or let is continue to start the installation process. now screen goes to next step and key board and mouse stop working . it stop me from further step. Please help
SamTry booting to our live image and see if that lets you use the mouse and keyboard. http://linux.dell.com/files/openmanage-contributions/omsa-71-live/
-
Solaris 8 x86 system refuses to upgrade to Solaris 9
My x86 system successfully runs Solaris 8 (Feb. 2000 revision A) but refuses to upgrade to Solaris 9. When trying to boot one of the installation cds in anyone of the installation modes, the boot process proceeds till the message "booting kernel/unix, ... use is subject to license terms". Next I would expect setup messages for the network interface, but instead I get a blank screen with a cursor blinking top left, and that's the end of it.
Well, to be true, it's not really a problem of Solaris 9. The same thing happened when I tried to install a patch set on Solaris 8.
What ways of diagnosis do I have?
Is anything in Solaris 8 not upward compatible?
Thanks in advance for every hint!
Bernd.OK after the DCA scans, it goes to a screen labeled "Boot Solaris" which indicates the boot drive. On that screen f4 is labeled Boot Tasks. Press f4 and go thru the settings to select the boot device and any of the other settings you might want to change. then f3 back to the boot screen and f2 continue. When the boot options screen appears, type in b -r. The DCA should not start up each time after that. To be honest, I had to do this a couple of times before something unknown to me made it finally work. Go figure!
Lee -
Latest (November) EIS-Patching ISO for Solaris SPARC & X86 systems download.
Hi All,
I hope someone can assist as this has given me a headache for the last few days.
I require the latest (November) EIS-Patching ISO for Solaris SPARC & X86 systems.
I require the ISO and not just the Patch set.
Please advise.
Kind regards,
PaulThe current ISO (october) is available at the usual place : EIS for Partner
And for information, the next planned EIS will be available very soon but not this month. -
Solaris 10 - After installation read only file system
Dear All,
I have installed the Solaris 10 on my x86 system with out any problem. The installation was completed successfully. I have followed the installation instructions that are mentioned in the following link.
http://docs.sun.com/app/docs/doc/817-0544/6mgbagb19?a=view
I am facing a different problem. I am not able to create even a single file / sub-directory on any of the existing directories. It always says READ ONLY file system can not create firl / directory.
Please help me how to resolve this issue.
Thanks in advance.
Regards,
Srinivas GWhat do you get for 'svcs -xv' output?
Darren -
Power Mac 5260/100 System CD
I found a eBay store selling what appears to be a Power Mac 5260/120 System CD containing Mac OS 7.5.3. Would this System CD also be compatible with a Power Mac 5260/100 by any chance? I'm asking because I happen to own a Power Mac 5260/100 I bought second hand off eBay.
I would think that there is a high probability it would work. If it's not too expensive, it's worth the chance of buying.
Cheers, Tom -
Is there certain version of Oracle can be installed on Solaris9-x86 system
I want to setup a Oracle database system under Solaris9 x86-based platform for study. Anybody know is there certain version of Oracle can be installed on Solaris9-x86 system? If it is, where to download? I just have Solaris9 x86 version, who can tell where can I download Solaris8 x86 version??
ThanksI've been reading lately about Apple's ongoing battle with Adobe over mobile apps and Flash. What I've gotten from all of it is that Apple wants to develop a mobile format replacement to Flash, and Adobe wants to block it. Apple's contention is that Flash is too bulky and consumptive for mobile apps and content. Apple has barred any mobile apps for iPhone and iPad from containing any Flash code, and Adobe says that has hurt their development of SDKs for people who want to make iPhone apps. It's turned into a regular peeing contest.
I would have to assume that Apple iPhone, DROID, and Windows Mobile all have the same issue with Flash content and software, since they all have to fall within the standards for mobile communications in order to be "universally accessible" by all the companies that make PDAs, tablets, and phones.
I've yet to see a Flash Player download for Windows Mobile, and given the current environment, with HTML 5 coming soon, it's not likely I will.
Maybe you are looking for
-
Hi All, I am having a report in which I am displaying data about the materials, description their cost etc. Now my requirement is to check the authorization for the person executing the report. Here , there are two plant and i have to restrict the p
-
Sending a BufferedImage to a printer.
I have a BufferedImage object that I want to send to a specific color printer. First, I send the BufferedImage to this method, which sets up the printer job. public static void printOutChart(BufferedImage imageToPrint, int intCopies, String name) {
-
Google links to Ad Sites and unrequested audio plays in background
1) When I click on links from Google searches it redirects to Ad websites... 2) When I have Internet windows open suddenly audio (that sounds like it is coming from other unopened websites) will start playing.
-
Where did my applications, music files and many others go in Lion?
I recently installed Lion. Today I was looking for some files on my MacBook Pro. When I used the finder to search for files (like music, etc.) all of the files within the finder were empty! It doesn't even show a list of applications...help!
-
Can anyone help me find the solution - JFrame problem?
HI, I have developed an application using JFrames; instantiating a new frame to display each new screen of the application as the user moves from screen to screen and back. However when I move from screen1 to screen2 then back to screen1 and back to