Solaris x86 on Compaq DL360 (P21) server
I am having issues installing this OS on the server in the title... it is a DL360 with Dual PIII 998 processors and 1.4G RAM.
I setup the RAID controller at statup to use RAID1 with 2 x 36G drives.... and then boot from the Solaris Disk 1 (no the installer disk)...
I am using the RAID controller driver supplied from Compaq for Solaris 8 and at the first stage it successfully is added during the installation process....
The process goes through as per expected, setup network, setup drive layout and even install required OS modules.. then it happens....
... the request to insert the disk holding file CPQARY2 pops up, disk is inserted but the message 'file cannot be found on disk' is returned....
Silly thing is that the system has already used this driver from this disk to load the HDD RAID conntroller info into memory... it even installs to the disks with no problems....
Is this an issue because the drivers are for Sol8 and not 9??... and does anyone know where and if I can get the drivers for 9??.. they are not on the website for this server model....
did you make any experiance regarding Solaris 10 X86 ?No, but...
Unfortunately there is no Solaris 10 driver for the
built in SmartArray of the DL360 (P21) available.... I expect that the same workaround is OK for Solaris 10, that is,
rename the DU/sol_28 directory to DU/sol_210 on HP's driver
update floppy.
Similar Messages
-
Hi, I am trying to install Arch on a HP (formerly Compaq) DL360 1U server.
The problem is that setup can't see the disks attached to the reaid controller, presumably because it does not have a driver for it.
Has anyone else done this, if so how was it fixed?
If not, how do I get support for it? Do I need to compile a new kernal for it? If so is there a readme or something that will help.
I do have access to many working arch box's.
Many thanks
Benedict WhiteI installed a RHEL-knockoff (TaoLinux) onto a DL380,
it reports the following through LSPCI:
00:00.0 Host bridge: ServerWorks CNB20HE Host Bridge (rev 23)
00:00.1 Host bridge: ServerWorks CNB20HE Host Bridge (rev 01)
00:00.2 Host bridge: ServerWorks CNB20HE Host Bridge (rev 01)
00:00.3 Host bridge: ServerWorks CNB20HE Host Bridge (rev 01)
00:01.0 RAID bus controller: Compaq Computer Corporation Smart Array 5i/532 (rev 01)
00:02.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
00:04.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
00:05.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
00:06.0 System peripheral: Compaq Computer Corporation Advanced System Management Controller
00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 51)
00:0f.1 IDE interface: ServerWorks OSB4 IDE Controller
00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 04)
07:07.0 PCI Hot-plug controller: Compaq Computer Corporation PCI Hotplug Controller (rev 12)
modprobe lists the SCSI host adapter as:
[root@inf-linux-dev root]# cat /etc/modules.conf
alias eth0 e100
alias eth1 e100
alias scsi_hostadapter cciss
alias usb-controller usb-ohci
Does this help any? I haven't tried to install arch on one of these yet. -
How to integrate a Solaris x86 server on Sun Management Center ?
Hello people,
I want to integrate a Solaris x86 server on Sun Management Center platform.
If I'm not wrong, SunMC doesn't run for Solaris x86, server and client only as console with Java.
In speat of it, I try to install Sun Management Center 3.0 Agent for Solaris x86.
It seems to be ok, install packages, but when execute es-setup script, intents to create the following directory:
/opt/SUNWsymon/base/bin/sparc-sun-solaris2.8
I supose that in this directory, SunMC will install sparc binary files
At this point, I can't follow the installation and abort it.
Can anybody give me ideas to install and integrate my solaris x86 server on SunMC ?
ThanksHi Hisham,
hishooooo wrote:
Dear Gents,
I have one X86 Solaris Server configured and installed to be Sun Management Center Server.
successfully i could monitor the Sun Solaris Servers after i have installed the SMC agent on them.
my problem is that i could not install the SMC agent on Red Hat Linux. as i could not find an easy document or steps to do so.
could you guide please?If you still have a copy of your SunMC media around, the same ["es-inst"|http://docs.sun.com/app/docs/doc/820-2215/command-line-1?l=en&a=view] program you use to install Solaris Agents should work on Linux as well. It autodetects OS type and will install Solaris packages or RPMs as appropriate.
Regards,
[email protected]
http://www.HalcyonInc.com -
How to integrate Solaris x86 server on Sun Management Center ?
Hello people,
I want to integrate a Solaris x86 server on Sun Management Center platform.
If I'm not wrong, SunMC doesn't run for Solaris x86, server and client only as console with Java.
In speat of it, I try to install Sun Management Center 3.0 Agent for Solaris x86.
It seems to be ok, install packages, but when execute es-setup script, intents to create the following directory:
/opt/SUNWsymon/base/bin/sparc-sun-solaris2.8
I supose that in this directory, SunMC will install sparc binary files
At this point, I can't follow the installation and abort it.
Can anybody give me ideas to install and integrate my solaris x86 server on SunMC ?
ThanksHi
From the Unix prompt enter oemapp console(for v9.x). If you are using earlier versions it is oemapp console (for starting the console) and oemapp dbastudio(for starting dba studio)
For starting OMS enter: oemctrl start oms.
Hope this helps
sarath -
Weblogic Server 9.2 MP 3 for Solaris x86
Does anyone know where I can download weblogic server 9.2 mp 3 for Solarix x86. I have spent my entire day looking for it in support.oracle.com (metalink) and oracle download pages but nothing has turned up so far.
You can always ask via support.
There is a download on edelivery.oracle.com. Select Oracle BEA then Solaris x86 32bit - then click on BEA WebLogic Media Pack for Sun Solaris x86 (x86, x86-64)
You'll see a 9.2 MP3 ISV download, I'm not sure if that's exactly the same as the normal one or if it's only for ISV's, you'd have to ask support. -
Can I set two router IP on my solaris x86 server?
Hi ,
I want to make traffic balance on my office. Because we have two leased line.
I would build up NAT in the solaris x86.
Can I set two router ip in the solaris x86 server? And How to do it?
The traffic balance is work or not?
If that is not work, what can I do?
Thanks All ^_^
Andrew ChoiYes, you can use solaris x86 as a NAT box.
add another ethernet interface, and install
IP-filter, or sunscreen
I suggest you search the solaris newsgroups on
http://groups.google.com for more specific links to
how-tos -
Solaris 10 (x86 version) as a jumstart server
Hi,
I have a pc with cdrom and a netra T1 without cdrom.
Wondering if I can use solaris x86 pc to jumpstart netra T1(sparc). I heard linux can jumpstart solaris sparc.
thanks
justinI have a pc with cdrom and a netra T1 without cdrom.
Wondering if I can use solaris x86 pc to jumpstart
netra T1(sparc). I heard linux can jumpstart solaris
sparc.You can. The only problem is that it is difficult to read the information from the SPARC CD set (due to the differences in x86 and SPARC UFS filesystems).
If you have the SPARC DVD (or even just the DVD .iso), then it's easier. The same information is replicated so that it is easier to copy onto x86.
Since you only have CD drives, I'd recommend copying the DVD image to the machine, then using lofiadm to mount it up.
Once mounted, it's the same thing as on SPARC, just run the setup_install_server and add_install_client stuff.
Darren -
Migration from Solaris Sparc server to Solaris x86
Hi ,
I would like to know.
Migration from SAP ECC6 , Oracle , Solaris Sparc to Ecc6, Oracle, Solaris x86 , Is this consider Heterogeneous or Homogeneous system copy?
Thanks.
Best Regards,
ck chaiSolaris on SPARC is a BIgEndian platform, Solaris on X86 is LittleEndian - so it's heterogeneous --> you need to use R3load to performa a migration - and you need to have a certified migration consultant on-site to do that migration (http://service.sap.com/osdbmigration --> FAQ).
Markus -
Controller issue on Compaq DL360 (First Generation)
I just don't want to warm up this old thread here, but meanwhile: Is there any known solution/workaround for the problem, that an installation of sol 10 on machines of this type (or DL370s/DL380s, using the same controller) fails, ending up in the 'no disks found' problem?
I assume, I am not the only one who experienced the fact, that the folder renaming procedure of the somewhat older driver disks supplied by HP (cpqary2 for the integrated smart array controller, contained in Compaq SoftPaq SP21874, V 1.70A for Solaris 8, http://h18023.www1.hp.com/support/files/server/us/download/16328.html) doesn't help any further.did you make any experiance regarding Solaris 10 X86 ?No, but...
Unfortunately there is no Solaris 10 driver for the
built in SmartArray of the DL360 (P21) available.... I expect that the same workaround is OK for Solaris 10, that is,
rename the DU/sol_28 directory to DU/sol_210 on HP's driver
update floppy. -
Solaris on Dell/Compaq Multi-CPU servers?
Am interested in hearing from anyone who has used Solaris 8 on either a Compaq or Dell server with multiple CPUs. Have a client interested in such a configuration, but am concerned that since that isn't a bundle option, that I may be helping to steer them down a difficult road.
Thanks,
EwanSolaris 8 worked OK for us on a compaq proliant dl360.
Compaq has solaris 8 <a
href="http://www5.compaq.com/support/files/server/us/locate/38_1123.html">
driver update diskettes
</a> that you must use during install to access their built-in raid
controllers. -
Problems installing Sol 10 x86 on Compaq Harware
Please Help! I am a newbie to Solaris and I am trying to understand some of these postings in this thread. I am trying to install Sol 10 on a Compaq DL360 with dual proc 1.26 MHZ and 3 GB RAM. It has an imbeded 5i array controller with two 36 GB drives attached set up as RAID 0.
I have downloaded the Sol 8 UTI disk for the controller and seem to be able to successfully add the driver for installation. Note: I renamed the directory from Sol_28 to Sol_210 as instructed earlier in this thread. I get a warning message after loading the driver that says :
Solaris could not detect a primary disk.....
However, the system has detected a disk controller without a driver, and assumes that the following disk maps to the primary disk:
/pic@0,0/pcie11,4040@1/cmdk@0,0:a
Choose continue to confirm the Solaris bootpath of the primary disk.
I press F2 to continue.
I continue with setup and choose Interactive text console. It boots the kernel then I get some memory resource overlap warnings but setup continues. Then I get two warnings that read...
Warning: /pci@0,0 /pcie11,4040@1/sd@0,0 (sd1): Request Sense couldn't get sense data
and
Warning:/pci@0,0/pcie11,4040@1/sd@0,0 (sd1): Sychronize cache command failed (5)
Setup continues...
I choose language as English and get same two warnings again. Setup continues. I enter network config info, and set root password then continue. Then installation starts and I get this error...
One or more disks are found, but one of the following problems exist:
Hardware Failure
Unformatted diskThen I push f2_ok and I get kicked out to shell.
What am I missing? Did I miss something? I tried this on another machine, a Compaq Proliant 800 with a 4200 controller with same results. Any help would be greatly appreciated.FYI: I tried yet another version of solaris as i found out that theres a bug in the 64-bit kernel on update 4 for alot of new processors. Solaris 10 x86 update 7 did the trick! :). Installed right away on a standard 'Solaris 10 (64 bit)' VM. I still find it strange that the most recent version of solaris 10 fails to even start the installation.
-
Mounting a Solaris x86 CD/DVD from a remote Windows CD/DVD-ROM drive
Greetings, all.
Is it possible to mount a remote Windows CD/DVD-ROM drive? I have the Solaris 10x86 Companion Software DVD sitting in a CD/DVD-ROM drive that's installed on a Windows server on my network. It is shared-out (F:) and the two servers can ping each other. I've also confirmed the NFS services/daemons are running on the Solaris x86 machine. I've tried the following variations but, all have failed to produce successful results:
# mount -F nfs x.x.x.x:/f /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f
# mount -F hsfs x.x.x.x:/F /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F
[FYI: S10_106_SOFTWARE is the DVD's label as reported by Windows Explorer.]
# mount -F hsfs x.x.x.x:/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/s10_106_software
# mount -F nfs x.x.x.x:/S10_106_SOFTWARE /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F nfs x.x.x.x:/s10_106_software /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/s10_106_software
# mount -F hsfs x.x.x.x:/F/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/s10_106_software
# mount -F hsfs x.x.x.x:/f/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/F/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/S10_106_SOFTWARE
I've also tried mounting it at bootup by adding the appropriate entry in the /etc/vfstab file but, this does not work as well. I've tried Google'ing for an answer to my issue but, I haven't been able to find anything that applies directly to what I'm reporting. It's usually chatter about mounting from one UNIX server to another. Any advice from the community would be greatly appreciated.After three weeks, you deserve a reply. Windoze does
not natively support NFS.Also deserves a decent answer...
There are two ways to do this:
Install Microsoft's free "Windows Services for UNIX," which includes a Windows NFS server; or
Install the 'sharity' package (google for it); it provides Solaris systems the ability to mount Windows shares -
Oracle 8.1.5 Client/WLS/Solaris x86
has anyone been able to get Oracle's client 8.1.5 running on Solaris x86 in conjunction with WLS to talk to back-end Oracle? Any help would be greatly appreciated.thanks.
This will not work. We have not built the native libraries to work with
Solaris on Intel..
I suggest trying the platform independent type 4 JDBC driver available for
free from Oracle. It is supported (as is any JDBC driver) with WebLogic
Server. To download it:
Go to http://www.oracle.com and select the "Download" option.
From the resulting page, use the "Select Utility or Driver" dropdown to
select Oracle JDBC drivers
From the resulting page, scroll down a little (since SQLJ stuff appears at
the top).
Or, to go directly there:
http://technet.oracle.com/software/tech/java/sqlj_jdbc/software_index.htm
Thanks,
Michael
Michael Girdley
BEA Systems Inc
"Dean Davis" <[email protected]> wrote in message
news:3a267487$[email protected]..
has anyone been able to get Oracle's client 8.1.5 running on Solaris x86in conjunction with WLS to talk to back-end Oracle? Any help would be
greatly appreciated.thanks. -
From 7.3 on NT to 8 on Solaris x86?
Has Oracle ported Oracle8 for Solaris x86?
Hi,
usually I expect people to do a little research and I do not give everything chewed.
Point 4:
go to the
<b>Oracle9i Database Migration Release 2 (9.2)</b>
go to the chapter 3
<b>Upgrading a Database to the New Oracle9i Release</b>
go to the point:
<b>Upgrade the Database Manually</b>
Exactly from here:
http://download.oracle.com/docs/cd/B10501_01/server.920/a96530/upgrade.htm#1009200
Keep in mind
1) that the <i>EXACT </i>procedure you are following it is not indicated in this manual
2) you have to think a little ( do you have all the windows services created on the destination system? if not, you have to create them ... )
3) this procedure is not supported by SAP. It is a valid option but not supported by them. You have to practice until you get all the points correctly -
Help with evaluation for Solaris x86
Hello,
I would like to evaluate Oracle Identity Manager and Access Manager products at the latest version possible -- the host system(s) are Solaris x86 (SunOS .5.10) Unfortunately, I am having a bit of trouble compiling the list of packages/versions to achieve this for this platform. For instance, on the downloads page it appears that OIM is not available for Solaris x86, not even in older versions(?)
Thank you in advance,
ScottHi Scott,
I'm pretty sure that x86 Solaris is not yet certified to run the Identity Management suite. I've been involved in an evaluation process and we ran it all on RedHat Enterprise Server Release 4 Update 5, without too many problems.
cheers,
James
Maybe you are looking for
-
BI Publisher Report not generating the PDF output.
I have developed the rdf report and concurrent program with xml as output format. Based on xml output I have created pdf template and created Data Definition and Template in XML Publisher Administrator Responsibility. Now I am comming to the concurre
-
Since I've installed Mountain Lion, I am having lock up issues with multiple programs. MS Outlook has crashed and I've lost all my folders. HELP?
-
Problem in getting the parameters from teh form html with upload file
I have used the jspsmartupload package: the html file: <HTML> <BODY BGCOLOR="white"> <H1>jspSmartUpload : Sample 5</H1> <HR> <form METHOD="POST" ACTION="sample5.jsp" NAME="PW" ENCTYPE="multipart/form-data"> <table CELLSPACING="0" CELLPADDING="3" BORD
-
Problems Logging Into OTN/My Oracle Support
Yesterday everything was fine. Today when I log in with my preferred account through my company I am unable to log in but used an old personal account to get in. I am also unable to log into My Oracle Support with my company account. Since I can't
-
When i receive mail with enclosed photo's then the photo's are displayed in a large size. Is it possible for me to change that? Thanks in advance, René Haagsma