SOLMAN SMD Wily Introscope

Hi!
Has some one experience working with Wily Introscope 8.0?
I use currently the version 7.2 and would like to upgrade this version to Wily Introscope 8.0.
When I do so I cannot install and run Wily Introscope 8.0.
Any helpful information will be very appreciated!
regards
Axel Schulze

Hi Axel
I am planning to un-install my current wily 7.2 and plannign to install 8.0, can you let me know if you have already completed upgrading and also can you send me details on the upgrade.
Thanks
Reddy

Similar Messages

SOLMAN SMD Wily Introscope: no dashboards are available

Hi!
I would like to use the SAP SMD functions and Wily Introscope 8.0
I am on SAP SOLMAN 7.0 EhP1.
The problem I have: when I start Wily Introscope no dashboards are available.
Can some one help me to solve this problem?
Thank you very much!
regards
Axel

You might have already checked the SAP Note 797147 and installation guide for Wily I 8.0 at
http://service.sap.com/instguides -> Installation & Upgrade Guides -> SAP Components -> SAP Solution Manager -> Release 7.0 -> Wily Introscope 8.0 - Installation Guide
From the installation guide could you confirm section ..."Check That Introscope Is Running Properly"
Also confirm you have set Java VM Parameters...
I think you need to check the Installation guide thoroughly.
Let us know if you have any error log or something....
All the best.

Wily introscope issue after System refresh in solman 7.1 Sp11

Hello experts,
Unable to remove old Production wily in quality system.
An new wily has installed in development box but when i run Solman_setup -> basis configuration ->cofig wily
Unable to unassign or delete old wily introscope
Thanks ,
Rahul Yedapally

Hi Rahul,
Check in expert mode , diagnostic agent of development system should appear in quality SMD agent administration as you are assigning DEV wily to SOLMAN QUA.
and all so make sure RFCs WEBADMIN , SOLMANDIAG and
NONE are working fine in SOLMAN.
Thanks,
Prakash Reddy Maram

Solman E2E diagnostics and Wily Introscope.

Does anybody have any time scales for setting up Solman Diagnostcis and Wily Introscope. I have a quote for this work and would like peoples past experience of time scales for this.
I have a 3 system landscape PRD, QUA, DEV and obviously SOLMAN.
I need to set up the SMD agents on each server involved and install the required Wily components

HI,
If you have downloaded all the necessary s/w then you complete the E2E RCA setup in 1 day for one system(including buffers) including Wily.
E2E RCA config, can be completed as part of solman_setup. Once you have completed your initial and basic setup, solman is ready for managed system config.
I would recommend following timeline including buffer
two - three days for Basic configuration and initial configuration.
Installation of SMD takes less than 20 mins/ host. Wily installation also should not take more than an hour
Managed system config - this depends on which application are you configuring. in case of SAP application, you should be able to finish one SID in one day (including buffer)
BR,
Shyam

Wily Introscope for SOLMAN 7.1

Hi All,
We are configuring SAP Solution Manager 7.1
I have few doubts regarding Wily Introscope.
1. Is it necessary to install Wily Introscope on SAP SOLMAN 7.1?
2. Is it installed already with SOLMAN or need to be installed manually?
3. I need details about licensing policy of Wily Introscope.
4. If it is necessary to install please provide suitable link for installing it.
and I have one more question.
We getting waring message for Single Sign On and WEB Services Logical Port Creation in Managed System Configuration Step No. 8 Configure Automatically.
Shall we proceed with warning. or it needs to be fully performed without warning.
Please guide us.
Thanks & Regards,
Ishan

Ishan trying to answer all your doubts:
1. Is it necessary to install Wily Introscope on SAP SOLMAN 7.1?
If you need to implement RCA then only Wily Introscope is required.
2. Is it installed already with SOLMAN or need to be installed manually?
It has to be installed manually..Just follow the standard guide..
3. I need details about licensing policy of Wily Introscope.
Good Question..I think there should be someone in your orgnisation who looks after the licencing..Ask him to give a call to SAP..
4. If it is necessary to install please provide suitable link for installing it.
Follow this link :
http://www.scribd.com/doc/36673011/Wily-Intro-Scope-8-Installation-Guide
Thanks & Regards,
Joydeep

Is Wily Introscope a requirement with Solman 7 ehp1

We are finishing and upgrade from 3.2 to 7 EHP1.
Due to limited system capacity we have not installed the Wily Introscope product. At this time we were not planning on using its functionality. We are wanting to keep the basic functionality of solman 3.2 plus add the MOPZ piece.
I'm using the solman_setup tcode to go through the basic config wizard now. I've reached the Landscape Data step where it is asking for the Wily Introscope info. Since it doen't exist, can I bypass this step?
Thanks for your advice.
Laurie McGinley

Thanks Jarad,
That is what I thought (it isn't required), but needed to double check before I bypassed that bit of the setup.
Appreciate the quick response too!
Laurie

Error while installing Wily Introscope

Hi All,
I have installed introscope enterprise manager 8 in solution manager 7.0 (SP15). i have follwed the below steps:
1. Installation and Setup of SAP Solution Manager Server:
               upgrading SAP Solution Manager Diagnostics (SMD) package
               running Diagnostic setup wizard
everything went successful.
in the next step of wily introscope installation i have followed the below steps:
2. installing CA Wily Introscope
           I.   Download Third-Party External Component Package from CA Wily
           II.   elected Platform Independent Introscope Installer
           III. Extracted the Introscope Installer
          IV. Added the External Component Package
          V. Started the Installer
          VI. Verified the Installation
          VII.Installed the SAP Management Modules
         VIII.Ran the Enterprise Manager from OS level (AIX)
          IX. Checked That Introscope Is Running Properly
          X. Extracted the Introscope Agent
          XI. Created an AutoProbe Connector
         XII. Activated the Agent: Setting up Java VM Parameters -
here I am facing the issue
in the installation manual it has been given to add the below java parameters to server node:
-Xbootclasspath/p:/usr/sap/ccms/wily/connectors/connector.jar:/usr/sap/ccms/wily/Agent.jar
-Dcom.wily.introscope.agentProfile=/usr/sap/ccms/wily/IntroscopeAgent.profile
-Dcom.wily.introscope.agent.agentName=<AgentName>
i have added the above parameters and resterted the server then the java engine is not coming up. conflicting with the first parameter. once I remove that parameter I am able to up the java engine.
without being added the above parameters " the agent will not start".
please help me in this.
thanks in advance
Mohan K

Mohan,
I have the same problem. That is I set up the SMD on the managed system and completed the Managed system configuration through Solman which Installed Wily Introscope. With Wily enabled , the Java server process does not start.
If I delete the 3 lines that have wily in it, it starts OK.
How did you resolve this problem. Please let me know in detail.
Thank you.
Ravi

Solman SMD setup

Hi,
We have upgraded our solman 7.0 to EHP1, we did not make use of solman functionality so decided to bring in various functionalities like E2E, wily, RCA etc.,
Being naive to this area I am in need of clarifications to my doubts...
1. Does SOLMAN_SETUP would install, setup everything I need to run E2E, wily, RCA?
2. Does SOLMAN_SETUP covers all the steps which can be done from http://<>:<>/smd/admin or both are different?
3. is SMD and RCA both same
Finally we want to implement wily, RCA from our very fresh Solman in our landscape.
Kindly put me in right track to accomplish my work. Thanks in advance,
Regards,
Brahmeshwar.

hi,
SMD agent need to install on satellite systems like ECC, BI, PI, EP etc (single or dual stack) and configure agents on solman system.. Once you configure those agents, you would be able to configure the RCA through workcenter and below are the benefits of using solution manager with latest EHP installation.. Wily is a add-on tool and better to install on seperate machine and configure on solman
SMD is used to carry out centralized analysis and monitoring of the SAP Netweaver system landscape. It helps to simplify the task associated with root cause analysis.
Architecturally, the SMD is made up of four (4) main components namely:
SAP Web AS ABAP
SAP Web AS Java
Willy Introscope: Used for performance analysis and optimization. The server component is called introscope enterprise server while the client is called introscope agent.
The capabilities of SMD includes:
Central log viewer
Central display of configuration data
HTTP analysis
Single activity trace
Java thread dump
Database monitoring
OS monitoring
CCMS monitoring
Statistics data monitoring
Software changes documentation
Load test with mercury load runner (used for unit, regression testing)
CCMS monitoring
Performance Optimization
Thanks
Suresh

Wily Introscope Clarification

Can someone help clarify where I'm supposed to install the Wily Introscope Manager?
I installed on my solution manager server, is that correct?
I thought that the Wily Manager goes on Solution manager server and the wily agent goes on sap web applications. Please help me clarify.
thanks.

Hi,
You have to install the ISAGENT on solman only. Later you deploy it on managed systems via:
http://<server IP>:<port>/SMD
Managed systems-> introscope agent
If you mean the Enterprise Manager it's installed normally on the SOLMAN host. On windows it runs as a Service.
For official documentation:
Introscope Version 8 Installation Guide For SAP:
https://websmp104.sap-ag.de/~sapidb/011000358700001995842008E.PDF
On page 4 you'll find nice explanation regarding your question.
and also check: Note 797147 - Wily Introscope Installation for SAP Customers
Cheers,
Diego.

Wily Introscope Agent does not start

Hi,
i am installing Solution Manager Diagnostics on a Solution Manger 7.0 System. At the moment i am on the point to install the Wily Introscop Agent and i have following problem:
At first i tried the automatic setup and deployed the agent with JSPM and it seemed to work. I see "ISAGENT" on the System Information -> All Compontents over http://0/smd/admin and there is no log directory in the wily directory?
Does anybody has an idea whats wrong?
Best Regards,
Stefan
Edited by: Stefan on Feb 17, 2009 8:57 AM
Edited by: Stefan on Feb 17, 2009 9:31 AM

Hello Stephan,
1. Wily IS Agent (2 agents) is installed ONLY in SOLMAN system.
2. Then, with SOLMAN_SETUP Guided procedure, in third phase (Managed System Configuration),
    you deploy the Wily IS Agent to your managed system.
To summarize :
1. Install the ISAGENTxxx.SCA in SOLMAN only !
2. Start the SOLMAN_SETUP guided procedure
3. Phase I - Initial Configuration
    Phase II - Basis Configuration
    Phase III - Managed System Configuration.
In Phase III, there are 6 steps :
1.     Connect Managed system
2.     Check Prerequisites
3.     Manual Configuration
4.     Diagnostics Configuration
5.     Wily Introscope Configuration
6.     Create Logical Components
The Wily IS Agent (2 agents : IS Agent wich monitored JAVA instance and Wily Host-level Agent which a sub-process of the SMD Agent) is configured and STARTED here.
So, you cannot start / stop by any OS command the Wily IS Agent.
You start it from SMD.
Hope it help you.
Best regards
Pascal Cuennet

Wily Introscope prerequisite

Hello,
We want to implement Wily introscope in our landscape . We have 1 Solman and 6 systems to be monitored.
I had the following queries.
1. What are the prerequiste of the wily introscope.
2. Do we need SMD implemented on the systems to install wily.
3. If SMD is required pls let me know the prerequisite of SMD.
I have already gone through CA Wily 8.0 installation guide on SMP. I was not able to find the prerequisite.
Looking forward for your guidance.
Cheers!
Sammy

Hi
1. Refer http://www.sap2048.com/wily-introscope-installation-for-sap-customers-17.htm
2. Yes, preferred.
3. You may need to patch the SMD agent for wily8.0. As for the SMD agent itself, there is no requirement other that 1GB of space. It is available in all standard SAPINST.
Cheer!!
Javed

Problem Remote Deploy Wily Introscope Agent

Hi,
I installed Wily Introscope EM and the Diagnostic Agent on Solution Manager (EhP1).
Now, if I understand it, I can do a remote deploy of Introscope Agent, for example on Enterprise Portal.
How can I do?
Best Regards.
Diego.

Hi Diego,
Do you also install an SMD agent on the portal system which one you want to managed via RCA? Also you need to run the Setup Wizard for Managed Systems for your portal.
Please check SAP Note 1365123 - Installation of Diagnostics Agents. In this note you will find an attachment Agent_Installation_Strategy.ppt - describe the installation strategy of SMD agents and all agent rules which you need to follow.
So one part is to get RCA running:
1. Install a SMD agent per managed host.
2. Define the technical system in SMSY Normal you have an SLD in your landscape and connect the Solution Manager to it or use the SLD from Solution Manager. After you define the technical system in SMSY or via SOLMAN_SETUP ->Managed System Configuration you go to Diagnostics Setup.
3. You access this via Diagnostics work center or direct link http://solman_fqdn:<port>/smd
4. Next go to Managed System -> Setup Wizard -> Select your to managed system <SID> - > check that system is Diagnostics Relevant (if not click on the managed products and set the relevant product for diagnostic u2013 also verify the Landscape setting light are green u2013 this means the technical system is well defined in SMSY)
5. Click Setup <SID> Button -> on next screen you need to fill out all Java / Abap connection parameters (for the setup of Java systems you need a userid with j2ee admin rights)
6. Please set the SMD agent in the right table u2013> Click on details arrow and then select the managed systemu2019s SMD agent and click on the set button. The SMD agent will now reboot wait until the agent is back -> Click on the Refresh button to see the status.
7. Click Next and on the next screen you get a Summary of all setup steps
8. Click on Setup. After the setup finished (all steps are green)
9. Click on quit.
Before your can deploy the IS agent from the Solution Manager you need to deploy the IS agent files via SDM to the Solution Manager. You can download the deployable IS agent from SAP Service Market Place:
Support Packages and Patches -> Entry by Application Group -> SAP Technology Components -> SAP SOLUTION MANAGER -> SAP SOLUTION MANAGER 7.0 EHP 1 -> Entry by Components -> Agents for managed systems -> select your version for your IS EM and download the deployable agent via SolMan Diagnostics (File name like ISAGENTSMD801_01-10007435.SCA)
Now you can start with the setup of the Introscope Agent (on the left menu bar under application selection).
On the selection screen select first your IS Enterprise Manager then the IS Agent settings the relevant system.
In the table select the J2EE node for which want you setup the agent (this need to be done for each Server node u2013 the IS agent runs inside of the J2EE node per server)
Then click on Setup Introscope Agent u2026 Button u2013> select the Autoprobe Directives and click the Apply button. If every steps doen you need to reboot your managed JAVA system.
Now you are ready to use the RCA tools and also see data in the IS Enterprise Manager.

Extend Wily Introscope in Solution Manager

Hello, Could I monitor other non SAP solutions in Solution Manager?
I need to integrate all systems that are intended for monitoring (SAP
and non SAP systems) to Solution Manager
What is the scope of Wily Introscope in Solution Manager? Is the scope
only with SAP products or I could extend Introscope's capabilities to
other products?
Thanks for your help
Best regards
Edgar Rafael Escobar Molina

What is the scope of Wily Introscope in Solution Manager? Is the scope
only with SAP products or I could extend Introscope's capabilities to
other products?
The Introscope coming with SolMan is only a part of the full Introscope suite. It contains only those applications necessary to monitor SAP systems. For other non-SAP systems you would need different agents which are not delivered and must be purchased separately. I´m also not sure if the Solman license permits the usage of those agents in non-SAP environments.
Markus

How to IMPLE SMD/Wily?

Hi
Need some information
1.what are the OSS Notes which say SMD is required for troubleshooting for SAP components like, PI 7.1, Netweaverr 7.1, Netweaver 7.0 or any specific component like AS Java 7.0 troubleshooting.
2.How to findout which version installed in my system of Wily introscope and SMD agent ?
3. What is the latest version of Wily introscope and SMD agent available. Does any of the installed SAP components(PI 7.1, BI 7.0, BIA 7.0, MDM 7.1(forthcoming)) require a upgraded version of Wily/SMD agent?
4.what special requirements for the new version of the SMD/Wily?
Regards,
Neni

Hi
Have you refered
https://websmp210.sap-ag.de/~sapidb/011000358700000048292009F/
This got almost everthing
Also refer to : https://websmp110.sap-ag.de/support and Solution Manager Coloum for more informaton.
Cheers
Deepanshu

Wily Introscope Enterprise Manager Can't be accessed

Hi Experts,
I installed Solution Manager 7.0 EHP1 and executed basic configuration. And I followed the instruction to install wily EM 8.0. But after installation, the web pages http://emhost:8081/workstation and http://emhost:8081/webview cannot be accessed. Error msg is "404 Not Found The requested resource does not exist."
I've checked the wily log and found no errors. How to solve the problem?

Hi ,
Check if the installation of EM 8.0 was successful or not.
For the same, please check <Introscopehome>/install/Introscopeinstall.log.
I am hoping your installation is successful. Then please perform some other checks.
Please start your Introscope Enterprise Manager service from Windows Services [ for other OS please refer to guide]
Check the <IntroscopeHome>/log/IntroscopeEnterpriseManager.log
file for an Error entry.. there may be a possibility that the Port 8081 [or 8080] is already in use.
Similar format to error message :::
"EM Web Server did not start. Port already in use: 8080 To change the Web Server port, modify the EM property: introscope.enterprisemanager.webserver.port "
If yes, then please modify the \conf\EnterpriseManager.properties file
introscope.enterprisemanager.webserver.port=8080
OR
introscope.enterprisemanager.webserver.port=any other open port
For more details about changing port please refer to Thread
Wily Introscope Enterprise Manager 7.2 is not starting on SolMan system
I hope the provided information will be helpful.
Best Regards,
~~ Pradeep Bishnoi ~~

SOLMAN SMD Wily Introscope

Similar Messages

Maybe you are looking for