SOLUTION FOR 3110 RESTARTING!!
Finaly I hawe hawe found the solution for restarting problem!
1.Format your memory card
2.Make shortcut on your mobile so u can access very fast to your media player
2.1. In SETTINGS/DISPLAY/ACTIVE STANDBY/ACTIVE STANDBY MODE (TURN ON)/PERSONALIZE VIEW (MAKE IT THAT SHORTCUT BAR IS THE ONLY ONE THERE)
2.2. In SETTINGS/MY SHORTSUTS/NAVIGATION KEY make it so that standby key is 2nd
2.3. Get back to main screen and press DOWN key,options, select, select media player, and save, in organise shortcuts make it 1st and save your progress
3.Upload up to 5 songs
4. Update your media player, mobile will restart him self! BUT!!!...
5. In order to stop restarting u have 3 sec to start updating music library again
6. If u done all at step 2, u need to press fast one time down,central button,left blue line,down,central,up, and central (Need to be pressed in 3 seconds)
7. If u success in this 6th step u hawe solwed problem!
8. Next step is to upload next 5 songs and repeat steps 4-6
(9.) If you cant press so fast buttons to restart uploading I suggest to create a folder named "Amp3" so he can be first when u access to your memoru card so you could
erase him fast to stop restarting, instead formating whole card (In SETTINGS/MY SHORTSUTS/LEFT SELECTION KEY(Make it Gallery, so you can access fast to memory card to delete folder "Amp3"))
(10.)Buttons to erase "Amp3" folder - While in main screen press : Left blue line,center,left blue line,down,center,center (Need to be pressed in 3 seconds)
(11.)You hawe stopped restarting and kept pics, and images on memory card
If this work at your phone just tell me because I would like to know did i helped
[email protected]
You may want to try this:
1. Backup iPad
2. Setup iPad as new. Settings>General>Reset>Erase all content and settings
3. Test iPad thoroughly
4. If everything is fine, restore backup to iPad
Similar Messages
-
my ipad is taking restart automatically and screen is fully balck and showing only apple logo.please give me solution for that
Have you tried a reset first? If it works, you won't have to go through the restore process.
Hold down the sleep (upper right hand top) and the home button at the same time. A slider will appear. Ignore it and keep holding down the buttons. The Apple logo shoud appear. Then your ipad might work again. It takes a good 15 seconds. You will not lose anything on your ipad.
If you try it a couple of times and it doesn't work, you might have to go through the restore process as has been suggested above. But follow the steps so you don't lose your data.
Hope this helps. -
Does anyone has a solution for this problem?
Since I updated to iOS 6 sometimes my keywords did not work.
I always have to restart my iPhone to have it work.
It's ridiculous to always restart my phone.
If you also have this problem you can repost + give some tips.
Thanks and greetings,
Max LouisHi Alo816,
I'm sorry to hear you are having such extensive issues with Messages on your iPhone. If you continue having issues sending or receiving Messages, you may find the troubleshooting steps outlined in the following article helpful:
iOS: Troubleshooting Messages - Apple Support
If you continue to have issues with Messages after that troubleshooting, especially if it is still having or crashing, you may want to make sure you have a current backup of your data in iTunes, then try restoring your iPhone to factory settings and testing it in that default condition to see if the issues persist before restoring your data. You may find this article useful:
Use iTunes to restore your iOS device to factory settings - Apple Support
Regards,
- Brenden -
I have installed 2010 Microsoft office 2010 home and business version for my laptop,and I have installed lync 2013.Now i want create online lync meeting from outlook,but i am unable view that lync icon in outlook.Please give me the solution for this issue.
Regards
RaghavendarHi Raghavendar,
Generally, when you install Lync 2013 in the computer with Office 2010, a Lync Meeting Add-in will be installed and enabled in Outlook 2010. Please follow these steps to check it:
1. In Outlook, click the File tab, click Options, and then click
Add-Ins.
2. Please take one of the following actions:
If the add-in is in the Inactive Application Add-ins list, follow these steps:
a. In the Manage drop-down list at the bottom of the dialog box, click
COM Add-ins, and then click Go.
b. Click to select the check box next to the add-in, and then click OK.
The New Online Meeting button should now be available in
Calendar View, and the Online Meeting button should be available when you create a new calendar item.
If the add-in is in the Disabled Application add-ins list, follow these steps:
a. In the Manage drop-down list at the bottom of the dialog box, click
Disabled Items, and then click Go.
b. Select the add-in, and then click Enable.
c. Restart Outlook, and then verify that the add-in is displayed in the
Add-ins dialog box.
The New Online Meeting button should now be available in
Calendar View, and the Online Meeting button should now be available when you create a new calendar item.
3. In Event Viewer, view the Application log to see whether an error was logged for Outlook, for Lync 2013, the Lync Meeting Add-in for Microsoft Office 2013.
Thanks,
Winnie Liang
TechNet Community Support -
After update my iPad 2 with IOS 6.0.1 the botton mute and sound + doesn't work...any solution for this??? Thanks
There are numerous reports of this issue happening on iPhones. It may be a glitch that will need a new update. Some find that a full shut-down and restart fixes that problem, but not always.
-
I bought iPhone 3GS(Used) recently and updated ios 6.1.3 my iPhone is taking blurry Pictures through basic default Cam app.Can anybody please let me know any solution for this?
Basic troubleshooting steps right out of the user guide are restart, reset, restore from backup, restore as new. If you've been through ALL the steps and you still have the problem, then you'll need to bring your phone to Apple for evaluation.
-
A possible solution for "foreight language keyboard shortcut" problem...
Hi(Bonjour)!
Everyone know the problem of losy keyboard layout when Final Cut is used with foreight language keyboard. We loose the COMMAND-Q shorcut.
As PieroF suggested in many posts in final cut express forum, there is a workaround:
"+I just installed Leopard and I ran into this keyboard shortcut problem.+
+I can confirm that:+
+a. the problem exists also with the Italian keyboard (in addition to other languages, as pointed by other posters)+
+b. the workaround I described in my previous answer works fine :+
+- close FCE (if open)+
+- open System Preferences/International/Language+
+- drag English to the first place on top of the other languages+
+- drag your own language (Italian in my case) again on top of English (at the end the window will show the same original settings, but something happened in the heart of Leopard...)+
+- close System Preferences+
+- open FCE: now all shortcuts work as expected, and are correctly listed with their corresponding menu commands+
+It's a workaround, it's not convenient (I'd better have this bug fixed), but apparently you have to apply it only once for each system startup.+
Piero "
As stated by Piero, you have to follow this procedure after each computer startup.
I found a way to restore the COMMAND-Q shortcut with the keyboard and mouse system pref panel.
Simply add Final Cut application and add a +custom shotcut+. Be careful to type exactly the "Quit Final Cut Express" menu.
This solution allows to restart the computer.
It's work with Final Cut Express and Final Cut Pro under Leopard 10.5.4.
Michel BoissonneaultHi Michel,
I like your suggestion because the keyboard shortcuts defined in the system preferences do not require redefinition at each startup. So in theory we could define all missing/wrong shortcuts this way, and not only the cmd-Q as you suggested. Boring, but we could do it once for all.
The only problem is that I don't know how to define shortcuts for submenus, for example "Render Selection/Both": it seems system preferences allows only to define shortcuts for the menu ("Render Selection" - in this case absolutely useless) but not for the submenu.
Do you know a way ? (I looked in the help, which didn't... help).
Piero -
Oracle Installation or Uninstallation Solutions For Windows 95/98/2000/ME/NT/XP
You must read carefully the following steps here. If you previously installed any Oracle's products on your machine, I strongly recommend you to clean up thoroughly before install the new products.
================================================================
Uninstallation
The easiest way to remove ALL traces of Oracle software, for an 8i installation, is:
(1) Using regedit, remove the key \\HKEY_LOCAL_MACHINE\\SOFTWARE\ORACLE.
(2) Remove all the Oracle services (usually called Ora-something) from \\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services.
(3) Go to the ORACLE_HOME directory (usually C:\Oracle\Ora81). Go to the BIN directory beneath this. Rename the file OCIW32.DLL to something like OCIW32.OLD.
(4) Reboot your box.
(5) Once you have logged on again, delete the directories C:\Program Files\Oracle and C:\Oracle.
(6) Right-click on My Computer, select Properties->Environment. Edit the environmental variable PATH to remove all refernces to files in the two directories you have just deleted.
(7) Remove the Oracle folders from your Start menu.
*** Obviously, using regedit on your machine always entails risks, and I won't be held responsible if you end up trashing your system. However, the above procedure is one I have used many times with complete success. You have been warned! ;) ***
As to logging on, the "standard" Oracle accounts are:
SYS/change_on_install (SYSDBA - database owner)
SYSTEM/manager (Owns various VIEWs and utility PACKAGEs)
and (optionally):
SCOTT/tiger (Training account containing some sample tables)
If you're using PO8i on the local machine, you shouldn't need to worry about setting up NET*8 (Oracle's networking protocols)
=================================================================
Windows 95 and 98
This will remove all Oracle products, Oracle services, and Oracle registry entries from your computer.
Complete the following steps to create a Clean Machine. Backup any relevant databases before proceeding!
On Windows 95 and Windows 98:
1. Ensure you shutdown your Oracle. Right click on the Oracle Icon in the toolbar and click on the shutdown option.
2. Un-install all your Oracle products if possible. Use universal installer to do that. Ignore this step if you dont have universal installer on your machine.
3. In regedit, go to HKEY_LOCAL_MACHINE\SOFTWARE\ORACLE.
4. Delete the ORACLE key.
5. Edit your AUTOEXEC.BAT file and remove your %ORACLE_HOME%\bin and JRE paths from the path setting.
6. From the Windows Explorer (or from the command prompt), delete the Oracle directory (Oracle Base).
7. Delete <system_drive>:\Program Files\Oracle (from the Windows NT Explorer or from the command prompt).
8. Delete Icons from <system_drive>: \Windows\Start Menu\Programs\Oracle - <HOME> and <system_drive>:\Windows\StartMenu\Programs\Oracle Installation Products. Where <HOME> is the previous HOME name.
9. Reboot your computer.
On Windows NT:
1. Ensure you are logged in as a user with Administrator privileges.
2. Stop all Oracle Services through Control Panel Services. Use universal installer to un-install your Oracle products. Ignore un-install if you dont have universal installer on your machine.
3. Using regedit (at the command prompt, type regedit), go to HKEY_LOCAL_MACHINE\SOFTWARE\ORACLE and delete the ORACLE key.
4. Open HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services, and remove all keys under HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services that begin with ORACLE.
5. Open HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\EventLog\Application, and remove all keys under HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\EventLog\Application that begin with ORACLE.
6. Close regedit.
7. From the Control Panel, open System.
8. If JRE was installed by Oracle, remove the %ORACLE_HOME%\BIN path and the JRE path. For example, you may see a path similar to this one: C:\ORACLE\ORAxx\BIN;G: \Program Files\Oracle\jre\1.1.7\bin. Go to Start > Control Panel > System > Environment tab. Click on the system variable path and modify the path.
9. Delete Icons from <system_drive>:\Winnt\Profiles\All Users\Start Menu\Programs\Oracle - <HOME> and <system_drive>:\Winnt\Profiles\All Users\Start Menu\Programs\Oracle Installation Products. Where <HOME> is the previous HOME name.
10. Delete <system_drive>:\Program Files\Oracle (from the Windows NT Explorer or from the command prompt).
11. Reboot your computer.
12. Delete all ORACLE_BASE directories (You can find the Oracle homes listed in HKEY_LOCAL_MACHINE\SOFTWARE\ORACLE\ORACLE_HOMES).
================================================================
Doc ID:
Note:131299.1
Subject:
Oracle Installer 8.1.X Hangs on Machines with Pentium 4
Processors
Type:
ALERT
Status:
PUBLISHED
Content
Type:
TEXT/PLAIN
Creation
Date:
02-JAN-2001
Last
Revision Date:
18-APR-2001
This alert was modified 16-January-2001 by specifying specific
Oracle Universal
Installer Versions in the the Versions Affected section.
Oracle Universal Installer (OUI) for 8.1.x Hangs on Machines
with Pentium 4
Processors
~~~~~~~~~~~~~~~~~~
Versions Affected
~~~~~~~~~~~~~~~~~
Oracle 8.1.5
============
Oracle Universal Installer 1.6.0.9.0
Oracle 8.1.6
=============
Oracle Universal Installer 1.7.0.19.0
Oracle 8.1.7
==============
Oracle Universal Installer 1.7.1.9.0
Platforms Affected
~~~~~~~~~~~~~~~~~~
Any platform that uses the Intel Pentium 4 processor, with the
Sun JRE
and Symmantec JIT will encounter this problem. Windows NT,
Windows 2000
and NetWare platforms are confirmed to be affected.
Description
~~~~~~~~~~~
When installing Oracle Products with the Oracle Universal
Installer (8.1.x)
on machines that use the Sun JRE and Symmantec JIT, the
installer hangs.
Specifically for the Windows platform, the following version
of the Symmantec
JIT or earlier will encounter the failure:
Symantec Java! JustInTime Compiler Version 3.10.107 for JDK
1.2.
Details regarding this issue can be found at:
http://developer.intel.com/design/processor/future/manuals/knowni ssue.htm
How to determine if you have Symmantec Java for JDK 1.2:
1. Select the file "symcjit.dll" and right click on it.
2. Select Properties, then the Version tab.
3. Under Microsoft Windows*, the properties of the DLL are:
"Symantec Java! JustInTime Compiler Version 3.10.107 for
JDK 1.2 Copyright (C)
1996-99 Symantec Corporation Dynamic Link Library file".
DLLs older than this will also not work. "
Likelihood of Occurrence
~~~~~~~~~~~~~~~~~~~~~~~~
Any platform that uses the Intel Pentium 4 processor, with the
Sun JRE
and Symmantec JIT will encounter this problem. Windows NT,
Windows 2000 and NetWare platforms are confirmed to be
affected.
Possible Symptoms
~~~~~~~~~~~~~~~~~
The failure typically is that the affected application simply
terminates.
Workaround
~~~~~~~~~~
Not only will OUI be affected by this bug, most of the
post-install
configuration tools will also be affected. Running these
tools with "-nojit"
specified will avoid the hang, but it is not simple to specify
"-nojit" for
some of the products.
The following workaround works for the Windows operating
system:
a. Copy only the install directory from the CD to the hard
disk ,say, e:\temp.
b. Open oraparam.ini and make the following modifications
(Assuming CD
drive is f:)
* Change the "SOURCE=" line to use the full path to the CD
instead of a
relative path. (i.e., SOURCE=f:\stage\products.jar)
* Change the "JRE_LOCATION" line to use the full path to the
CD instead of a
relative path. (i.e.,
JRE_LOCATION=f:\stage\Components\oracle\swd\jre\1.1.7\1\DataFiles
\Expanded)
* Change the "OUI_LOCATION" line to use the full path to the
CD instead of a
relative path. (i.e.,
OUI_LOCATION=f:\stage\Components\oracle\swd\oui\1.6.0.9.0\1\DataF
iles\Expanded
* Change the "JRE_MEMORY_OPTIONS" line to add "-nojit" as the
first argument.
(i.e., JRE_MEMORY_OPTIONS=-nojit -ms16m -mx32m)
^^^^^^
* Other entries should remain the same
c. Launch setup.exe from the temporary location on your hard
drive (i.e.
e:\temp\install\win32\setup.exe). This will use the
modified
oraparam.ini and pick up the information from the CD since
the absolute
locations are specified.
Choose a Custom install and choose not to create a database
during the
install. This way, the Database Configuration Assistant will
not be launched
during installation.
The Net8 Configuration Assistant will still be launched, and
there is no way
to suppress it. You will need to kill the Net8 Configuration
Assistant if it
hangs due to the bug. The installation still will have been
successful, and
you can run the DBCA and NetCA after installation.
To kill NetCA if it hangs during installation:
In the "Configuration Tools" window, highlight the "Net8
Configuration
Assistant" and click "Stop". If that does not work, look for
the most recent
JRE process using the Task Manager, and kill it manually.
NOTE: the OUI
itself will also have a jre process. Be sure to kill the one
with the most
recent date, which should be the jre process being used for
Net8CA, not the
one for OUI itself.
After killing the configuration tools and continuing through
the installation
to the "End of Installation" screen, you should modify the
configuration tools
to use "-nojit", then call the appropriate tools from the
Start Menu.
Once installation is complete, each of the following files in
the ORACLE_HOME
needs to be modified:
assistants\dbca\dbassist.cl
assistants\dbma\dbmig.cl
assistants\ifa\ifa.cl
bin\elogin.cl
bin\owm.cl
ldap\oidamdin\oidadmin.cl
network\tools\netasst.cl
network\tools\netca.cl
owm\install\instelogin.cl
owm\install\instowm.cl
Edit the contents of the above files to add "-nojit" as shown
below:
Command=("C:\Program Files\Oracle\jre\1.1.7\BIN\JREW" -nojit
-classpath ....
this is the only thing you need to add --> ^^^^^^
Then, launch the necessary tools, like Net8CA and DBCA from
the Start Menu.
Patches
~~~~~~~
Currently there is not a patched installer available to deal
with this
problem, the workaround listed above must be used.
References
~~~~~~~~~~
[BUG:1507768] INSTALLER FAILS WHEN RUNNING ON NEW PENTIUM 4
(IV) PROCESSORS
[BUG:1507946] INSTALLER FAILS WHEN RUNNING ON NEW INTEL
PENTIUM 4 (IV) PROCESSORS
@[BUG:1518935] SYMCJIT.DLL DOESN'T WORK WITH THE NEW P4
PROCESSORS
Oracle
Support Services.
Copyright (c) 1995,2000 Oracle Corporation. All Rights
Reserved. Legal Notices and Terms of Use.
================================================================
The solution of making a local copy of the installation CD on
the hard disk and renameing symcjit.dll to symcjit.old does
work to allow installation of Oracle Client 8.1.7 on a Pentium 4
This function is useful and you can find two file to rename
===============================================================
Windows ME
Solution to the installation of Oraclei8.1.7 PE in Windows Millennium
Oracle does not support installing version 8.1.7 PE into
Windows Millennium.
As an unsupported workaround, you may add the following line
to the [compatibility95] section of win.ini prior to
installation:
Jrew=0x00080000
After setup is complete, Oracle will recommend a reboot.
There is one additional step necessary prior to reboot;
Oracle may add a non-standard path statement to the
autoexec.bat file. Please modify this SET PATH
statement to use short-filenames if you find a quoted
LFN string represented as part of the path. You can
confirm that the path was merged successfully into the
registry after reboot by examining the PATH variable
in the registry at
HKLM\System\CurrentControlSet\Control\SessionManager\Environment
Symptoms of a missing Oracle path statement in the registry are that Net8 Easy Config will not launch.
Please note that Oracle does not support the use of this
product in Windows ME, but have authorized these workarounds
for testing purposes only.
===============================================================
Windows XP Home Edition
Oracle 8i is not certified on windows XP. Even if yes, it must be Windows XP Professional.
You can install Oracle8i on windows XP Home Edition, try like this:
1 - Copy your Oracle CD into hard disk in your
machine. For example Copy from oracle8i CD into C:\Oracle\ ...
2 - Search the two files named Symcjit.dll on the D drive (where you have copied Oracle8i. You can found them in (example):
C:\Oracle\stage\Components\oracle.swd.jre\1.1.7.30\1
\DataFiles\Expanded\jre\win32\bin\symcjit.dll
3 - Rename this file (Example): symcjit_back.dll (make sure to find two files and rename them)
4 - Execute the Oracle setup.exe from C:\Oracle\setup.exe
===============================================================
When Oracle 8i dies on the install or the installer hangs, here is the fix for this, make sure that you have Service Pack 2 installed.
1. \JRE\1.3.1\ From Sun. (You can download java program at http://java.sun.com/products/jdk/1.1/jre/download-jre-windows.html)
2. Install the java file.
There is also a problem in the installation disk.
3. Make a copy of the Oracle 8i disk on the local hard disk.
4. Do a search for the two files called symcjit.dll and rename them for example: symcjit.old.
5. Install Oracle from the win32 directory.
================================================================
PLEASE NOTE THAT ORACLE DOESN'T SUPPORT THE USE OF THOSE PRODUCTS IN WINDOWS ME, BUT HAVE AUTHORIZED THESE WORKAROUNDS FOR TESTING PURPOSES ONLY
Best Regards,
Beau LeoHi,Beau Leo, I am having problem installing Oracle9i Database Rel.2 on my pc.
I read the suggestion and solution you posted for fixing Oracle 8.1.x installation
probblem, and since my pc also hung at 48% while installing Oracle 9i software,
I wonder if the same problem in the Oracle8 Vs.Pentium4 also exists for Oracle9i.
I have Windows2000,256RAM, Pentium3 1Ghz, and 13.8 free diskspace. But the installation always
hangs at 48%, my computer will just shut down and restart automatically without
even showing an error message. I have tried installing the Enterprise edition for 3
times already but everytime encountered the same problem. I've also tried custom installation
by selecting not to create database, but it also hung.
Before I started each installation, I always made sure that my registry and environment
path are cleared and that all the partially-installed Oracle files are deleted.
I hope that you or anyone who has a solution for this problem could be so kindly to help me out.
Thank you in advance.
ailee -
A solution for Secure Static Versioning problem in 1.5.0_10
Hi,
I have JRE 1.3.1_09 and 1.5.0_10 on my computer and I think I have solved static versioning problem.
My test computer:
- Windows XP sp2
- Internet Explorer 7 (on another computer also IE 6)
- Firefox 2.0.0.1
- JRE 1.3.1_09
- JRE 1.5.0_10
I. Solution for Internet Explorer 6 and Internet Explorer 7
1. Edit registry and add:
HKEY_LOCAL_MACHINE\SOFTWARE\JavaSoft\Java Deployment\Policy
DWORD: EnableSecureStaticVersioning = 0 (Hex)
2. Restart browser if started.
3. Start web page with java applet.
II. Solution for Firefox 2.0.0.1:
1. Install 1.3 JRE in the same parent directory as 1.5 JRE.
Because default default installation path for 1.5 JRE is C:\Program Files\Java\jre1.5.0_10 you need to modify
1.3 installation path from default C:\Program Files\JavaSoft\JRE\1.3.1_09 to C:\Program Files\Java\jre1.3.1_09
After installation check out that "bin" directory is in the following path:
C:\Program Files\Java\jre1.3.1_09\bin
2. Install 1.5 JRE in default installation directory: C:\Program Files\Java\jre1.5.0_10.
After installation check out that "bin" directory is in the following path:
C:\Program Files\Java\jre1.3.1_09\bin
3. Restart browser if started.
4. Start web page with java applet.
Note: HTML page must use <object> tabs for Internet Explorer or <embed> tabs for any other browser (e.g. Firefox). You need to specify correct classid in object and/or embed tag.
P.S. If anyone would like to discuss with me send me an e-mail to [email protected], but please post question to forum and just mail me a link to forum. I will write my answer to forum.
Hope this helps,
GrofatyI have been trying to find a solution for this issue at our organization for over 6 months. Finally, we have a work around to run multiple java versions for newer and aging java apps.
Thanks,
Adunlow -
"Blocked plug-in message" problem on my OS X 10.6.8 (Safari's 5.1.10). Any solutions for a non-techie (step 3 on Adobe Flash's instructions leads to dead end, i.e. product for sale). Thank you.
Prior to updating flash player, you must first uninstall all previous versions. Make sure you are downloading from the proper Adobe website = Adobe Flash Player Software
Flash Player Uninstaller
Repair permissions and restart your computer after the installations. -
Error when installing Lenovo solutions for small business [Screenie included]
Hello everyone.
Recently, I tried opening the pre-installed Lenovo solutions for Small Business software on my Lenovo e530 running Windows 7 Professional 64-bit version (Upgraded from Win 7 Home Prem 64-bit) but failed after getting a message for encountering a critical problem of some sort. I then tried restarting my computer and that did not solve the problem. And then, I decided to install an upgrade version of it from this website http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS030146. But before that I uninstalled the previous version by uninstalling Intel Small Business advantage customizations with Revo Uninstaller and I deleted all the related folders too with a thorough scan. Out of my expection, I got this message below saying that I could not proceed due to some unspecified error. Has anyone encountered the same problem before? Does anyone have a solution for this? I'm not sure if that's my computer's problem or from the driver itself. Thank you for your attention to this issue.Hi, dougy
This should be configurable under msconfig. This is a program that you can use to tell your computer which programs you want to start when Windows starts. To get to this program, type msconfig into the search bar in the Start menu. A window should appear. Check under the Startup tab and make sure that the Lenovo Solutions for Small Business program does not have a checkmark next to it. This should prevent this program from starting up when your computer turns on.
Hope it helps,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it. -
Has anyone come up with a solution for the WD Passport and Mavericks OSX issues yet?
I was wondering if anyone has come up with a solution for the newer Macbook Pro/Mavericks and external WD Passport not mounting problems?
I have a couple of year old WD Passport that worked fine in my old 2009 Macbook Pro, the problem is the old computer crashed.
My dilemna; My new 2014 Mackbook Pro will not open my WD Passport, called WD Support, their answer, sorry, nothing has been solved.
Is there anyway I can get access to my files on the Passport with any other software, or by using a PC.
I am aware of reformatting the HD, and have read all the forums I could find and have tried installing the WD Update as well, (with the support tech from WD) and nothing works.
I know that my WD Passport works, so please don't suggest checking it, or the cord.
I appreciate all the help anyone can offer, and I am with all the rest of you struggling for solutions.
Thanks so muchHi everyone, this is what I did
1. upgrade disks to the latest firmware
2. de-install ntfs-3g and MacFuse.
3. Re-install NTFS 3G without Macfuse.
4. Next step: Install OSXFUSE latest version with selection MacFUSE compatibility layer.
5. Last step: Install Fuse Wait
Note: between steps 2 and 5, I restarted my machine.
It worked for me, after about 4 hours. -
REAL Solution for " Cant Unmount Disk"
I have a G% 1.8 PPC. It is Primarily a Protools machine.
I have been using it for about 6 years. One of the hdds have been attached for 4years via FW400.
I recently upgraded with no problem from 10.4.11 to 10.5.8. At the same time I went from ProTools 6.9.2 le to Protools 8 le.
I have played sessions from a new external, mercury enclosed, hitachi enterprise hdd and the old hdd. But when i tried to reformat the mercury it would not UNMOUNT. That was last week.
Today I got a g-drive brand new and it does the same.
I have tried Terminal with commands :
killall finder
log / volume / ...
I got these methods from the old post. Nothing works and now all of my drives do the same.
What is the real solution for this?OK, here is something extra wonderful.
i called apple and they suggested that i do a pram reset.. So i restarted my 10.5.8 and did the pram reset.
When it started it was at 10.4.11. The Rep had never scene that before and transferred me to a higher level a second time.
Long story, short.... I had to start from scratch with a fresh drive and all. -
Solution for OPML error in SOA suite Startup (Win Vista x64 and older)
h1. Hi Folks!
When installing SOA suite on Vista 64 bit I encountered lots of problems. One of them was the following upon starting the SOA suite:
At 33% in the progress bar, the starter gives an error, returning a question about OPMN.
Caused by: oracle.ias.opmn.optic.OpticBadConnectException: Error connecting to OPMN (is it running?): Connection refused: connect
Being a newbie in this field, I resisted to learn everything (Oracle as part of a course of Busines Process Integration Laboratories at the University) about the works behind the package. Unfortunately, OPMN drove me crazy for days!
The main problem for OPMN is the unability for the system to handle certain issues.
One of the issues: When in a testing environment that is unstable (i.e. a laptop) some issues occur:
* sleep resume is not supported
* hibernation resume is not supported
* restart is not always working for all processes
(tested this with XP32 & XP64 SP2; SP 3; Vista 32 and Vista 64)
The main issue is with OPMN and the services that are started and controlled through it.
A solution for our workgroup has been made:
-create a reset.bat file
-use the following code:
+@echo off+
ECHO Step 1 in the server reset is running: Shutdown OPMN processes
D:\product\10.1.3.1\OracleAS_1\opmn\bin\opmnctl shutdown
ECHO Please continue the reset sequence by pressing any key
pause
ECHO Step 2 in the server reset is running: Restarting OPMN processes
D:\product\10.1.3.1\OracleAS_1\opmn\bin\opmnctl startall
END
The commands regarding ECHO and the pause break can be omitted, but for supervision it is better to see if all processes are started in working order.
Please note the absolute paths, these are from my personal setup as they are the default from the manual. Adjust if necessary.
As User Account Control (UAC) does interfere a lot with programs in Vista (32 & 64) and from SP3 also with XP, please assign administrator rights to the reset.bat file.
This solution should take care of the "OPMN (is it running?)" issue, without rebooting or cold restarting the server.
Edited by: user10221595 on Oct 6, 2008 9:18 AM-- self found answer
-
REQUIRED SOLUTION FOR BELOW SCENARIO
Hi Friends, I have a requirement as below Source NUM1 123456789 TARGETNUM1,2,3,46,7,8,9.... I WANT TO LOAD FIRST FOUR RECORDS FROM SOUCE INTO SINGLE RECORDS IN TARGET AND SO ON.. PLEASE PROVDE SOLUTION FOR ABOVE SCENARIOTHANKS IN ADVANCE
Hi All, We are using Informatica 9.5.1 and Oracle 11g as by metadata DB. Initially our INFA_DOMAIN_REPO password was expired, so we couldn't connect to repository. Then we reset the same password and we restarted infa services also. But when we tried to connect repository we faced "Failed to connect repository" error. When i try to connect to Admin Consol, page was not displayed. When we check the node.log file it had a error message saying "2014-07-20 04:45:37,553 ERROR [Monitor Guaranteed Message Logger Thread] [CCM_10322] While logging messages to the Log Service, the following error occurred: [[DOM_10022] The master gateway node for the domain is not available. Electing another master gateway. Wait for the election of the master gateway node to complete. If the problem persists, verify that the master gateway node is running.]. Fix the errors written to the node.log file. com.informatica.isp.domainservice.exceptions.ISPMasterNotAvailableException: [DOM_10022] The master gateway node for the domain is not available. Electing another master gateway. Wait for the election of the master gateway node to complete. If the problem persists, verify that the master gateway node is running" We checked all the env variables and all looking fine.Node is also running. Please help to uderstand this issue ans the fix. Thanks in advance Regards,JP
Maybe you are looking for
-
I have the ICloud icon on my PC - Windows 7 - and the program. When I try to sign in using my Apple ID, the message says that the ID is valid but I don't have an account. How do I get an an Icloud account?
-
Hello Friends, I have a scenario. I would like to create a order to cash cycle in such a way that the net value of the item in billing is Zero. I.e basically no AR is created in Billing document . Can you help me what steps will be required in order
-
My copy and paste is not working.
It works fine when I'm in Word or any other document, just not on the Internet. It looks like it lets me copy, but pasting is never an option. Where can I go to fix this?
-
Cannot find the root of your orgchart. The orgchart box may have been delet
Hi All I have searched to forum for similar issues, but none seem to apply to the errors I get in the CDS log. When try-ing to view the Orgchart, in the Orgchart Console I get the following message "Cannot find the root of your orgchart. The orgchart
-
How to add the cookie to the response/redirect?
Hi, Can someone provide detail on how to add the cookie to the response/redirect? The current object I have is the UserSession object and the Session Token (string). Thx.