Solution to my Audigy 4 Digital Output probs... please make a stic

I was recently playing Q3TA with my son when my overheat protection kicked in. I exited to windows to see the temp and throttle back my CPU a tad, and when I returned I had no sound from my digital output. Analog was working fine, however.
Setup:
Giga-byte GA-MA78GM-S2H w/780g chipset
Athlon 64 X2 5000+ BE
Integrated Realtek HD audio (disabled)
Integrated ATI HD 3200
2xGB 800MHZ DDR2
Creative Audigy 4
Boston acoustics Digital BA735 2. speakers
I went over every setting in all of my consoles, HQ's and drivers. I played with driver versions, DirectX versions, diagnostic programs and procedures in the knowledge base. In defeat, I even wiped out my XP install and started fresh with the Aud-4 removed, using analog on the integrated card thru headphones. Then I disabled the integrated card and reinstalled the Audigy 4 only to find that there was still no sound from the digital speakers.
Solution?
I[color="#ff0000"] unplugged the power to my speakers, and reconnected everything. As soon as the power was back up, the sound started playing (I had a .MP3 on for testing).
This stumped me for two reasons that occur to me know:
. These speakers (and possibly many others) don't fully power down when you turn the volume knob off and the light on the satellites goes out. The decoder and subwoofer unit keep their light on.
2. Apparently, some situations introduce a faulty signal to the digital output that scrambles the speaker units and they refuse to operate any longer.
Now I know, unplug the power to my speakers. My system works on all three sampling frequencies in "audio console" 44., 48, and 96KHz. None of the troubleshooting procedures touched my problem, because they didn't even mention the speaker setup, let alone doing a hard reset.
Please please please!
Make this a sticky for future me!!!

The Digital output jack on the card isn't of optical signal type.....you will need to get those I/O module mention bt johnston2 for optical connection.

Similar Messages

  • AUDIGY 2NX DIGITAL OUTPUT PROB

    I purchased Audigy 2nx USB box and i'm using it for playing my musical instrument connected through line-in. Now the SPDIF coaxial output is not functioning when line-in inputs are used and the second problem is when the line-in input is used the EAX effects are not functioning for line-input source.So is there any solution for this two problems?
    CLEOPAS.Message Edited by cleopas on 0-20-2006 08:39 PMMessage Edited by cleopas on 0-20-2006 08:4 PM

    No one knows where:
    With the "digital output only" set on the Analog Speaker Properties Custom tab
    is located at in window 7? i don't see this option anywhere. I had this option for XP.
    Definately frustrating.

  • Audigy Digital output ---- spdif in

    hello Creative team
    a question for a friend of me
    it's possible to plug the digital audigy card , in a Spdif amp input
    thanks for your help

    Yes, it's possible, but if your friend is talking about a multichannel receiver which also has multichannel analog inputs, connecting to those provides a much better match to the soundcard's capabilities.
    -Dave
    [email protected]

  • Digital output for SB Audigy 2 ZS Platinum Prob

    I am trying to connect SB Audigy 2 ZS Platinum to my Amplifier (Sony DVP-NS92V) via the SPDIF coaxial digital connection (I have also tried the digital output at the rear panel), unfortunitely the output i got is only on the left and right front speakers. I am currently having a 7. channel surround system. I have clicked both the dital output only under speaker settings and advanced control for play control, and I have also?tried by using both DTS and THX media file, but still does not work. Can anybody help ?

    With a digital connection (optical or coaxial SPDIF) that is normal. Check this sticky thread for more info:
    http://forums.creative.com/creativel...message.id=270
    Cat

  • How to disable SP-DIF (digital) output on Audigy

    Hi, I am using Audigy 2 soundcard connected to Altec Lansing ADA885 speakers. These speakers have built-in Dolby Digital Decoder, and of course SPDIF input for this. Additionally, they have inputs for analog front and rear speakers signal. They can be switched to different operation modes : Dolby Digital decoding, Dolby ProLogic decoding, stereo, and quad modes. I have connected them to my Audigy 2 using analog connections, and also digital output. The problem is, that they process both kind of inputs (analog and digital) all the time in most modes simultaneously. For example, when I set them to "quad" mode (for gaming) they process analog signal that Audigy deli'vers them, but also they attempt to decode the signal from digital input. This produces some kind of phase distortions (basses dissappear and the sound becomes slightly muffled). Possible solutions could be : - disable digital decoding in speakers when using analog output from Audigy - this can't be done, these speakers' decoder is not configurable, - disconnect digital cable when using analog output from Audigy - obvious solution, however not very comfortable - disable "ON-DEMAND" spdif output on Audigy card and enable it when necessary. This would be most satisfying option for me. But.... is it possible at all ? Just something similar to the "Digital output only" setting in soundcard panel, but in my case i'd like to have an option of "Analog outputs only". Thanks in advance for any help Greetings, Martin

    Hi Terry,
    According to your description, my understanding is that you don’t want the yollow bar notification to display when you open Access documents.
    This issue seems to be about the client application. Please compare the followings with the things that you did:
     1.Open the documents
     2.Click File->Options->Trust Center->Trust Center Settings
     3.Click Protected View, unselect ‘Enable Protected View for originating from the Internet’
     4.Click Message Bar, select ‘Never show information about blocked content’
     5.Click Macro Settings, select ‘Disable all macros without notification’
    In addition, as this issue is about Office, I commend you create a new thread in Office forum, more experts will assist you with this issue.
    Office forum:
    http://social.technet.microsoft.com/Forums/en-US/home?category=officeitpro
    I hope this helps.
    Thanks,
    Wendy
    Wendy Li
    TechNet Community Support

  • Dtt3500 and Audigy Gamer, digital output only 2 channel unless its D

    Ok I recieved a response concerning my last comment but unfortunatly it did not answer my question at all. I have a DTT3500 and a sound blaster Audigy Gamer hooked up with the digital out to the /8 din adapter. I try the advanced 3d demo that came with the Audigy software and I only hear the front 2 channels, no center and no rears. The demo where you move the little icons and sound moves along with it. I have 5. activated in my windows control center along with audioHQ and digital out only is selected. my DTT3500 has 4./5. digital selected along with dolby digital/pcm audio and digital in. I am not getting the effect of multisurround at all. My center works and my rears work because playing music I can use all 5 speakers. When I use the analogue outputs I hear multisurround from the advanced 3d demo but my center doesnt work. The analogue setup sounds better but without a center channel its useless to me. Am I doing something wrong? I am using the adapter and digital DIN, what gives? The only reason I noticed I wasnt getting surround was while playing games nothing comes from behind you even on 5. games. The goldmine demo doesnt even work right, when the bird flys behind you it disappears but there is still sound from the rears. Analogue fixes this without a center but the manual and setup say to use the digital din. Do I just have a setting wrong? I would like to experiance the full capacity of multispeakers in my games.

    Dennis,
    With these speakers the connection that I would suggest would be to use the Digital out on the back of the sound card into the DIN Input on the DTT3500's. This will require a converter cable for /8'' Minidin to standard DIN which can be purchased from here:
    http://us.creative.com/products/prod...0&product=0375
    You will also need a standard DIN cable (one should have shipped with your DTT3500's).
    This should give you 5. with digital output only enabled on the Audigy.
    Jeremy

  • Digital Output problem once again (WIN XP, Audigy

    I searched the forums with no luck, actually I searched the whole internet with no luck - so far.
    My problems in a nutcase:
    - I can't find the button for Digital Output (the one which enables it, Windows XP's sound mixer used to have that option with some ?windows build?, but I can't find it since I installed creative drivers, it's just gone...).
    - If I find the digital output on-button with your help, is it even possible hear music with add-ons trough digital-optical cable or should I buy some mono-cable? :O
    To be specific:
    I have the Creative Audigy 4 Bulk, which of course supports SPDIF Digital output. I bought expesi've optical cable that I could finally use my hifi 5. speakers with movies trought computer. I have new 700 euro amplifier, and it supports everything, so the problem isn't with that one, anyways, let's get touch with the real problem.
    What ever drivers I'm using, I can't find the digital output section anywhere. Creative drivers has one SPDIF-button, but it affects nowhere. So, I can't even get the Digital Sound on, because windows mixer has no button for that with my windows xp, weird. I also tried to install windows vista, and there wasn't either any options, where I could put the digital output on.
    Which drivers and which add-ons should I install to get that Digital Output to work.
    If I manage to find the button for digital output from some drivers, can I also listen music while it's connected via optical-digital cable, or am I just able to hear sound from dolby digital movies? Is it even possible to get everything work with my optical cable (music/games and movies at the same time).

    . Your card doesn't have optical output, only "coaxial" digital. You will need a stereo (or camcorder) cable with one mini jack on one end and 2 (or 3) RCA connectors on the other. The white RCA will be the one you need.
    The setting is on the "Creative AudioHQ" at the "Surround Mixer" selection. It is called "Digital Output Only". Or if you use the little icon on the taskbar, at the "Speakers" on "Speaker Selection" you have the same option (a check mark under the selection of speakers).
    2. If you read the FAQ, you will get surround sound (5.) ONLY from DVD-Video that are encoded in DolbyDigital or DTS and ONLY if you pass-trough the digital signal to the receiver to do the decoding. In ALL other cases you will get STEREO PCM signal.
    3. If your receiver is a decent one you should have an analog surround input (5. analog input). in that one you can plug the analog outputs from your card in order to have surround sound all the time (like in the games).
    Message Edited by SoNic2367 on <SPAN class=date_text>09-25-2006 <SPAN class=time_text>06:24 AM
    Message Edited by SoNic2367 on 09-25-2006 06:26 AM

  • Audigy 2 Value Digital Output O

    Hello
    I recently bought an Audigy 2 Value and connected it into my expternal amplifier via the digital out connector. Is there a digital output only option hidden somewhere that would mute all the other outputs? It isn't under the advanced window of Play Control, that's where my old SBLi've used to have it. Thank you!

    alright, i read the knowledge base articles and saw that the tests won't output more than left and right, but still, it's not working for my dvd's. i have my receiver set to "direct". is that right? i'm using windows media player for the dvd playback, should i try something else? do i have to install an AC3 codec? do i have to enable something in media player? anything please

  • Coaxial Digital Output on TV to SB Audigy 2 Val

    I have the Creative SB Audigy 2 Value card installed on my computer and the Altec Lansing GT505 surround 5. speaker system. I also have a Toshiba MD4FP DVD/TV combo. My speakers can only be connected using th standard red and white RCA plugs. My TV has a Coaxial Digital Output jack on the back and red/white/yellow plugs on the front that are used by my PS2. I understand the speakers cannot be connected directly to the TV unless I use the headphone jack but when i try that it sounds bac and I get sound out of only 2 speakers. Is there a way to connect a coaxial audio cable from my soundcard (i think it has the digital jack) to the Coaxial digital output on my tv? Will that give me the ability to play my TV through my speakers?

    Read the stickies.

  • Audigy 2 ZS digital output to tosli

    First of all thank you for reading, this question probable has been raised before (done a search but couldnt find an answer to it).
    My doubt is, i own a Audigy 2 ZS (neither Platinum or Pro) wanted to know if i can plug this soundboard to my hifi stereo, through a toslink cable. I know the output on the board isnt toslink, so im think of using a cable such as this http://nanosatelite.eu/b2c/index.php?page=pp_producto.php&md=0&codp=250 with a male toslink and a 3,5 jack on the other. will i get a digital output with this cable, can it do the job (its only digital stereo im aiming at). any advices i should know?
    wanted to be shure about this, before buying the cable
    thank you for your time
    Nuno

    If the cable has a in-build coaxial to optical conversion circuit then yes, otherwise (I think this is the answer for you) no.
    You need a device wich can convert S/PDIF coaxial to optical (TosLINK). Creative des have one but sorry to say ... your card isn't on list you can use it with. So, you need to get something simliar or DIY one (it's not very hard to do).
    Get:
    http://www.maplin.co.uk/Free_UK_Deli'very/Coaxial_to_Optical_Digital_Signal_Convertor_2929/Coaxial_to_Optical_Digital_Signal_Convertor_2929.h tm
    http://www.cablestogo.com/product.asp?cat_id=504&sku=4008
    http://www.m-audio.com/products/en_us/CO2.html
    There are? couple more (just google).
    DIY:
    http://www.electricstart.de/
    jutapa

  • New Dell, Audigy MB Advanced has no "enable digital output" b

    Hey all.
    I have a brand new Dell Dimension 550 system, on which I ordered the Audigy MB Advanced.
    Actually I intended to get the X-Fi Music soundcard, but apparently spaced out and clicked the wrong thing. Bummer for me. Oh well I'll buy it later.
    Anyway I have no digital sound from my speakers, which are Boston Acoustics Digital MediaTheater. This is the 4. setup that came with my '98 Gateway G6-450, back when BA and Gateway were partners. These are *not* some of the speakers (I think like their 735 series) that require digital drivers. It's either a single analog cable, or a single digital cable, to run the full 4. setup, from the subwoofer plugged into the PC.
    Analog sound works fine, but I cannot get digital to work. The problem lies, I believe, in that I don't think the software recognizes that digital output is possible. Again, this is the OE soundcard, but it has the blue input port, the green output one, the pink/grey microphone/rear surround output, and also a yellow and black port, which are for surround connections (that I don't need).
    I will be upgrading to a better soundcard, but for now I just want digital to work. This is a common issue with people going from Win98 to XP, it seems, but... though I've found a post or two on this forum, the FAQ on BA's site, and some stuff via Dell and the Web, I really can't figure this out.
    I've run the BIOS sound test, that checked out. No control panel option works to get digital output working, and I've confirmed with Dell that digital output should be an option. Should be able to click on Volume Control in the taskbar, which brings up the Creative Surround Mixer. From there, click Speaker Settings. I have Speaker/Headphone Selection set to 4/4. and the "Synchronize with Control Panel" box checked. Below that should be at least one more box, including "Enable Digital Output" or similar. But it's not present at all. Blank.
    I don't know if a software reinstall would work or not. Anybody know what's up, here?
    Thanks!
    =S2=

    I've recieved a reply from Support telling me to email Dell, but from seeing other posts and topics, I have seen that this is useless. Most of the other people who have encountered this problem have resolved it via Creative not Dell.....Why do I have to go to Dell? Argh ?Thanks for the reply though :\

  • Audigy 2 value where is the option for digital output? Help

    i have the creative inspire 5700 and the audigy 2 value but i cant find the checkbox for "digital output only"
    where can i find it's Pls help me !!!

    That is not the problem however it is located in the speaker setup window and all it does is disable the line outs, digital is always turned on and cannot be turned off. I suggest you re-read the 5700 manual. Tell me which lights you have on.

  • Digital output NI 9474

    Hello,
    I am trying to learn labVIEW DAQ, and right now I am trying to figure out how to use NI 9474 with labview. NI 9474 is a device with digital outputs. I have attached a (poorly drawn) schematic of how I have my real circuit wired. For some reason, the voltage across the resistor is 9v instead of whatever the digital output should be when i set daq assistant to be 1 sample on demand. When I change daq assistant to continuous samples, it reads 4.6v. So I am wondering what am I doing wrong and what should my digital output be?
    I have attached my vi file, so can someone please help me figure out how to use NI 9474 with labview?
    Solved!
    Go to Solution.
    Attachments:
    DO example.vi ‏44 KB
    schematic.png ‏16 KB

    You are supplying 9V, so you should have 9V going across the resistor.  I'm thinking what is happening with the Continuous Samples is that it is toggling between High and Low.  If you measured that with a DMM, you will get around 4.5V.  Measure with an oscilloscope to make sure what is happening here.
    There are only two ways to tell somebody thanks: Kudos and Marked Solutions
    Unofficial Forum Rules and Guidelines

  • Make USB-6001 digital output always high or low in C

    Hello all,
    I am new to the NI DAQ interface. I have an USB-6001 and I am trying to use this device to control some logic circuit in C. So what I want to do is:
    * set some digital output lines to high or low levels, and change their status when needed (in C).
    I have tested the device in NI MAX -> Test Panels, and found that the device is able to do this. Then I try to do it in C. I hace checked the examples, and the function I should use is the one called "DAQmxWriteDigitalU32". I have problem in understanding its input parameters. I have tried something with my own understanding, but it does not work as I expected. Here is one test I did:
    uInt32   data=1;
    int32 written;
    TaskHandle taskHandle=0;
    DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
    DAQmxErrChk (DAQmxCreateDOChan(taskHandle,"Dev1/port0/line7","",DAQmx_Val_ChanForAllLines));
    DAQmxErrChk (DAQmxStartTask(taskHandle));
    DAQmxErrChk (DAQmxWriteDigitalU32(taskHandle,1,1,10.0,DAQmx_Val_GroupByChannel,&data,&written,NULL));
    taskHandle=0;
    DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
    DAQmxErrChk (DAQmxCreateDOChan(taskHandle,"Dev1/port0/line0","",DAQmx_Val_ChanForAllLines));
    DAQmxErrChk (DAQmxStartTask(taskHandle));
    DAQmxErrChk (DAQmxWriteDigitalU32(taskHandle,1,1,10.0,DAQmx_Val_GroupByChannel,&data,&written,NULL));
    I want to simply set "Dev1/port0/line7" and "Dev1/port0/line0" to high level, but only "Dev1/port0/line0" responds me. The second parameter of the function DAQmxWriteDigitalU32 corresponds to numSampsPerChan. If i replace it (currently 1) with a larger value, e.g. 100, I can see that "Dev1/port0/line7" sends a number of 1 out, then return back to 0. So I guess the problem is just that I do not understand well all parameters of the function DAQmxWriteDigitalU32. Can anyone please tell me how I can set a digital output line to 1 or 0? 
    Thanks!
    Hongkun
    Solved!
    Go to Solution.

    Hello,
    Here is a link explaining the inputs of function:
    http://zone.ni.com/reference/en-XX/help/370471W-01/daqmxcfunc/daqmxwritedigitalu32/
    Also here you can find a lot of examples in ANSI C
    http://www.ni.com/example/6999/en/
    Randy @Rscd27@

  • PID Control - analog input, digital outputs

    Hello everyone,
    I am trying to use the PID toolkit to convert my existing feedback control system to one using PID or just PI whatever works best. Problem is that the tutorials out there discuss in detail about obtaining Analog inputs and using the PID output to control an analog output. Are there any tutorials that show how I can control my process variable which is an analog input by using the PID output to generate digital outputs?
    Basically, what I am doing is controlling the incline of my device with two digital outputs that control two solenoid valves. The angle is calculated from a calibration curve that plots distance sensor voltage with Angle. Any help would be immensely apprecitated. I want to try this out on my own before I post some vi's. Thanks!
    V
    I may not be perfect, but I'm all I got!

    That is exactly what I am doing currently. I have error bands specified around the target to make sure that it doesn't oscillate. But, under load conditions such as pulsed load conditions, the device goes out of bounds and the values trigger to correct for it. But, what I need is seemless or atleast seemless correction. Currently what I see is sudden adjustments to the incline. Please find attached what I am currently using. I am trying to get a more finer solution if at all possible.
    Note: Within 5% of the target = NO action
              Between 5% and 15% = Pulsed ACtion ( DO On for Pulse width time)
              Greater than 15% = continuous action until it reaches Pulse band
    I may not be perfect, but I'm all I got!
    Attachments:
    TDML_subElevationControl.vi ‏41 KB
    TDML_subPulsedValveFuntion.vi ‏16 KB

Maybe you are looking for