Solve paper size for HP Laserjet 1102w

My printer's configuration Information page shows A4 as default paper size. But when a print job is conducted it turns to be printed on Letter size eventhough I have chosen printing size A4 in printing preference.
How can I solve this issue? Your suggestion is highly appreciated!

If you go into printer properties - click on the devices settings tab, you should be able to change the default paper size setting under the "Form to tray assignment" heading. You can change either the Printer auto select or the tray selection. Click on the word - letter - you will get a drop down menu and should be able to change it to the paper size you want.
As you stated, you can also change it in your printer preferences.
Please remember that you need to check your application as well when you are printing. If you have your paper size selected to something different in your application and something different in your print driver, your results will be mixed.
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Similar Messages

How do I change the default paper size for printing?

I am running Firefox 3.6.3. Recently, the default paper size for printing unexpectedly changed to a user-defined size of 3.00" x 4.57". It used to be letter size (8.5 x 11). The default paper size is 8.5 x 11 for everything else. I have tried changing the size in the preferences dialog box and then clicking "default", but after I close Firefox or if Firefox opens a new window, the default size switches back to 3.00" x 4.57". Does anyone know how to fix this?
== This happened ==
Every time Firefox opened
== About 2 weeks ago

In "mine" dutch firefox 3.6.12 there is no option to change paper-size see
"about:config" Promise to be careful (and be!) Enter "print.postscript.paper_size" gives a empty screen
"paper_size" gives a few results
What about the numbers 4259872, 4784247 and what is the meaning of
paper_size, paper_size_type , paper_size_unit

Set paper size for image on roll paper

Q I am trying to set the paper size for a H 30cm x W 80cm image using roll paper on an Epson R3000 printer. Computer Dell I7 64b and using Elements 9. Thank-you, John

Garry - Many thanks for the reply. I was following the usual routine but I had never needed to use the 'User defined' box previously but it appears this is vital to the whole process when using roll-paper. I also found that the paper height becomes the Length when using roll-paper. I nearly entered the paper height (as requested) as 10m (length of roll) but you need to enter the length of the actual print required or the print process will start in the middle of the 10m roll! always seems to be that little extra missing from the manuals! John

Default paper size scanning problem, LaserJet M1120n MFP

Hi, I just got a used LaserJet M1120n MFP. Installed the most up-to-date drivers form HP's website. Printing is fine over USB or LAN, however the WIA scanning driver defaults to paper size "Letter" and I can't scan A4 pages all the way. The bottom is always cut off and I get an unwanted strip besides the scanned document. Please, advise how to change the default paper size of the WIA driver to A4. I use Windows XP Pro. Looked everywhere but cannot find any settings that will allow me to change the default paper size. Any ideas?
I have been thinking, could default paper size be somehow be tied to system locale? My locale is European and all other device drivers do default to A4. I wonder how the WIA scanning driver chose to default to Letter size.
The TWAIN driver works fine (I can choose default paper size), though it is less intuitive than I expected. Too bad I can't use it over a LAN. Is there a way to calibrate the scanner for white as the background seems kind of dark?
Your suggestions and ideas are most appreciated. Thank you.

Thanks for the reply, Spencer. I have used Adobe Acrobat to scan by means of the WIA driver, but when I do so the paper size selection box is dimmed (inactive) and I can't choose any paper size (nor any is preselected). I have also used Win XP's native Scanner and Camera Wizzard; it doesn't even have a paper size setting. Then I have used it with Win 7's native Windows Fax and Scan; no paper size setting here either.
Here is a useful thread on the same issue from Adobe's forum: http://forums.adobe.com/thread/844549
Reading around the forums I came across several posts where people discussed the impossibiity to set paper size when scanning using the WIA driver. Their problem was a bit different, though. The WIA driver had locked to size 'Legal' while they needed to scan in size 'Letter'.
The WIA interface was developed by Microsoft and here is what they have to say about the issue:
http://msdn.microsoft.com/en-us/library/windows/hardware/ff548440%28v=vs.85%29.aspx
'Supported Scanner Paper Sizes
Although two WIA user interface components are able to display a list of page sizes to the user, there is no easy way for a WIA driver to know which page sizes a scanner supports.
Page Size in WIA Applications
There are no WIA properties that allow WIA drivers to report supported page sizes or that allow applications to specify page size directly. To communicate page size settings to a driver, an application must calculate the required size in dots per inch (dpi) and adjust the origin of the scan to conform with the registration requirements of the device.
Page Size in the Common Scanner Dialog and in the Scanner and Camera Wizard
Both the Common Scanner Dialog and the Scanner and Camera Wizard have a static table of supported page sizes in which each page size is described by its horizontal width and vertical height, both in increments of 0.001 inch. These page sizes are currently displayed only when the scanner is in document feeder mode.
The largest page size (by area) that a driver supports in page feed mode, as determined by the maximum bed size, is considered the default page size. Paper sizes that do not fit on the feeder or on the bed of the device are not offered to the user.' -- exactly my case!
Having tried the same WIA driver (developed by HP in this case) on several PC's running different WIndows OS and using non-US locale settings, I have came to the conclusion that HP may have hard coded the Letter paper size in the driver. I guess this works for North America but not in Europe where A4 is the standard size.
I guess I have to look into ways to get to that hard coded paper size setting in order to be able to make use of the driver. I don't even know if that will be possible but I'll keep on reading. Wish me luck

Can't print using custom paper size for HP6520

I'm trying to print Hobby Lobby RSVP cards for a wedding. The size is 5.5" X 8.25". My HP6520 keeps giving me an error that the printer has detected a different size of paper and it won't print. I've gone to Custom and set the size to match, but it still won't print. I have the paper in the bottom tray.

Hi @Saltman1,
Welcome to the HP Forums!
I noticed that you cannot print on a Hobby Lobby RSVP card size is 5.5" X 8.25" with your HP Photosmart 6520 on Windows 8. I am happy to look into this for you!
According to your printer's specifications, this is an unsupported card size for this printer. The supported card sizes are:
Card type
Card size
3 x 5 in Index
76.2 x 127 mm (3 x 5 in)
4 x 6 in Index
101.6 x 152 mm (4 x 6 in)
5 x 8 in Index
127 x 203.2 mm (5 x 8 in)
However, as a workaround, you might be able to assign an alternate driver by going to this post, How to Assign Alternate Print Drivers in Different Versions of Windows, by @Shane_R, and then doing a custom size print by going to this guide, Create Custom Paper Sizes in Windows 7, Windows 8, and Mac OS X.
Otherwise, I would suggest getting the proper size of paper for this printer as indicated in the chart above.
Hope this information clears things up for you, and have a great day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Cannot enable ePrint Web Services - get internet connection error for HP LaserJet 1102W

I have a HP laptop running Windows 7 Professional 64 bit. We just changed over to Comcast internet service from AT&T where my HP LaserJet 1102W was set up for ePrint. After several hours, I was finally able to add the 1102W printer to the Comcast network, access the Embedded Web Server tool and print wirelessly but I cannot set up ePrint. I have deleted the printer but cannot get it to connect to Web Services. I keep on getting: Connection Error. Check Internet Connection but again, I can print wirelessly successfully to the printer but would like to be able to set it back up for ePrint. My Comcast router is an Arris TG862.
I have updated the firmware and used the HP Print and Scan Doctor tool but still am not able to get the ePrint Web Services to connect. Here is the information from the Networking page of the EWS:
IPv4 Configuration
Warning: A change in the IP Address will result in loss of connectivity to the browser.
IP Configured By: DHCP
Host Name: NPIC968F8
Domain Name: hsd1.tn.comcast.net.
IP Address Configuration
X Automatic IP Manual IP
X DHCP
BootP
X AutoIP
Manual IP Address:10.0.0.89
IP Subnet Mask: 255.255.255.0
Manual Default Gateway: 10.0.0.0
DNS Address Configuration
Preferred DNS Address: 75.75.75.75
Alternate DNS Address: 75.75.76.76
WINS Address Configuration
X Automatic WINS Server
Manual WINS Server
Manual Preferred WINS Server: 0.0.0.0
Here is my ipconfig information:
Wireless LAN adapter Wireless Network Connection:
   Connection-specific DNS Suffix . : hsd1.tn.comcast.net.
   Description . . . . . . . . . . . : Intel(R) Centrino(R) Wireless-N 1000
   Physical Address. . . . . . . . . : 8C-A9-82-A3-F9-5E
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::c57:eb2b:5144:2ea5%13(Preferred)
   IPv4 Address. . . . . . . . . . . : 10.0.0.3(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Friday, March 29, 2013 1:24:52 PM
   Lease Expires . . . . . . . . . . : Saturday, April 06, 2013 11:09:24 AM
   Default Gateway . . . . . . . . . : 10.0.0.1
   DHCP Server . . . . . . . . . . . : 10.0.0.1
   DHCPv6 IAID . . . . . . . . . . . : 378317186
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-15-CE-4E-8C-10-1F-74-11-22-71
   DNS Servers . . . . . . . . . . . : 75.75.75.75
                                       75.75.76.76
   NetBIOS over Tcpip. . . . . . . . : Enabled
There appears to be a known issue with the Arris TG862 router and supposedly a new firmware is to be released soon but just checking to see if anyone has been able to resolve this issue.
Thank you!

Hi Surf1981,
I understand that you're not able to enable web services on your printer. I would try steps listed below.
1. Open an internet browser type printer's IP address.
2. Should bring you to the printer's status page.
3. Select networking tab at the top.
4. Left hand side select Network Identification.
5. Under DNS address Configuration select Manual DNS Server.
6. For Preferred enter 8.8.8.8
7. For Alternate enter 8.8.4.4
8. Select apply. You might get a warning saying this could interrupt connection that's fine.
9. Turn printer off for about 30 seconds then try again.
**If you find this helpful or want to say thanks make sure to click the white star under my name to give me Kudos. **

Setting paper size for multi-tab numbers file?

i have a (currently) 3 tab spreadsheet that someone is working with me on. two of the tabs i print to 12 x 18 and one of the tabs i print to 8 x11.
right now i have to open inspector, set paper size to 8 x 11, go to print view and slider-scale to appropriate size so it will print to single width, open print dialog, select 8 x 11 printer, print the pages from this tab. then i go back to inspector, select 12 x 18, select next tab, go to print view and slider-scale to appropriate size so it will print to single width, open print dialog, select 12 x 18 printer, print the pages. then i select the next tab, go to print view and slider-scale to appropriate size so it will print to single width, and run a print to 12 x 18 paper.
this gets me all three documents if i didn't make a mistake somewhere and forget to select the correct printer or open inspector or whatever.
can someone tell me whether in numbers i can set a PAGE SIZE for a TAB (as i have done above) and have it stick or does the selection of a page size in numbers apply to the whole document? i keep sending this to my bookkeeper and getting it back and this is a whole lot of aggravation that is really messing up my workflow and there seems like i should be able to find a way to streamline this.
note: i am actually /receiving/ xls from my bookkeeper (and exporting to xls when i send it to her) and we also need to keep the tabs together b/c one tab is pulling info from the others but i am wondering if there could be some kind of workaround.
i'd like to ask her to just print the pages to pdf before she sends it to me but this is an added layer of work on her end that is not going to happen. also, i /can/ open in excel (i have excel for the mac) so if this works easier by printing from excel i will do that.
any experience with this issue would be greatly appreciated.
THANKS

hi Y. BIG time thank you for this. i was not aware this was such an issue. i definitely cannot have any ambiguities in my spreadsheet and customizing it in numbers is the whole reason i am spending this time formatting (i.e. to make it intuitive and visual).
that said, if accepting excel and then exporting to excel will cause problems i absolutely cannot have this.
can you help me a little more on what the problems are? i have already got a file with two tabs directly imported from Quickbooks (by my book keeper in excel) and a tab that she set up that pulls data from these tabs - and then i have MY tab that i have been customizing and proofing and fixing as i go along. more info on this work below.
are there commands i can run to clean this up?
what is considered OK to do in numbers if i am accepting excel (printing? adding new numerical entries)?
THANK YOU
background: right now i am /mostly/ doing formatting things like adding bold outlines or adding color or whatever but i have /also/ been dragging and dropping some rows to put them in a better place and fixing some cell sums that were either left out by my book keeper or which needed to be added to check THEIR work. are you saying that by doing this i am setting myself up for various formatting issues such as merged cells?
if so, once i finish the format of the spreadsheet and the tabs i can only exclusively open in numbers if this is necessary. are there some commands i can run to "clean up" issues? for instance can i go around the various tabs and unmerge cells to clean things up?
also, i definitely cannot split up tabs into individual documents as the customized spreadsheets are pulling numbers from a set of tabs that are quickbooks imports....

How to set the paper size for scan import

Adobe Professional 10 - How to set the import paper size to letter or A4 (for example). The only option is automatic and it scans legal size. Normally the options would appear but I have no options other than "automatic".

Moving this discussion to the Scanning & OCR forum.

Since upgrading to LR 5.6 I can no longer change paper sizes for user print templates.

The print preview window shows the new size laid out properly but the printer feeds only the size which was used to create the preset resulting in clipping if a larger paper and cell size is invoked in page setup or xs white space if a smaller is invoked. OS X 10.8.5, Stylus pro 7890. REINSTALLED PRINTERS AND DRIVERS, DELETED AND REPLACED LR PREFERENCE FILE, Other aps print ok. I

While the problem is unsolved I have found a workaround. If I use the "Printer" button (lower far right) and print from the printer dialed pop up custom paper sizes chosen in the "page setup" are honored and the layout prints as shown in the LR print preview). On the other hand, If I print using the "Print" button the printer feeds only the paper size chosen when creating the preset.
Bob H

[Solved]Right size for /boot

Which is, in your opinion, the right size for a /boot partition? Some guides suggest 50-100Mb, other 10Gb!
Who's right?
Last edited by frazar0 (2011-07-17 17:03:10)

Mine is 32MB; half used, half empty:
$ du -sh /boot/*
285K /boot/grub
8.6M /boot/kernel26-fallback.img
1.8M /boot/kernel26.img
163K /boot/memtest86+
1.3M /boot/System.map26
2.2M /boot/vmlinuz26
Last edited by lolilolicon (2011-07-17 15:10:00)

Setting A4 Paper Size for Smartform

Hi,
The Customer needs the output of a Smartform in A4 Paper but tilted.
As the width of the required output is more and the height is less, the content will fit into one single page but the page has to be tilted. How can I acheive it.
Thanks in advance,
Ishaq.

hi
good
here is the procedure in sapscript,you can try the same in smartform,
1.) Create the letter-size form, let's say: Z_DELNOTE.
2.) Try to make the first form flexible enough so that it can serve as a 'master form', with the only required difference being paper size.
3.) Copy that form into a new one, Z_DELNOTE_A4 and convert the paper size to A4. Adjust any windows as needed.
4.) Set up output config to point to the first form.
5.) In your print program, insert logic before the OPEN_FORM to append '_A4' to the form name field when appropriate (e.g. based on plant).
6.) Perform all subsequent changes to the first form and overlay the second one as in step 3.
thanks
mrutyun^

Print paper size for Purchase order

Hello,
We have purchase orders for Japan, Sweden. The requirement from business to print for A4 size and Legal size. What does Legal size mean? Does it mean 'Japan Legal Size' and 'Sweden Legal Size'.
Sincerely,
Sanjay

It is a size of paper
Non-ISO size typing paper, 81/2 inch wide and 14 inch tall, used almost exclusively in the UK, USA, and commonwealth countries. Also called foolscap size after an early trademark carried as a watermark.

Larger paper tray for hp laserjet pro 200 color mfp m276nw

Is there an additional tray for the m276nw

Sorry, the standard 150 page input tray is the only tray available for the HP Laserjet Pro 200 Color MFP m276nw.

[ SOLVED ] Partition Sizes For New Arch Install ?

Hi All
I have just picked up a new 250gb HDD and i'm going to do a clean install of arch & openbox and would like to know what people would suggest for various partition sizes ?
/root
/swap
etc
I have 4gb ram so not sure if swap is a required !
Many Thanks
Last edited by whitetimer (2010-11-15 09:58:47)

+1 on KlavKalashj's advice!
When the installer warns you about there not being a /boot partition either(besides the swap), then just select ignore, it's no problem at all!
If you do want a swap partiton(and don't hibernate), then I would say max 1gb imho.
For an Openbox based install, then I would say 10GB is more than enough(mine's 5, although with a tiling WM: Musca).
I don't keep the cache forever increasing, but empty it at times where I know everything is OK. Also, there's scripts available which cleans the cache up, like e.g. only keeping one revision back of each package.
Last edited by mhertz (2010-11-15 09:47:18)

[SOLVED] Help needed for HP laserjet 1000

Does anyone succeed in installing that printer on Arch? I tried the foo2zjs driver from AUR and to compile it from http://foo2zjs.rkkda.com/ but notting seem to work. I know that the firmware reach the printer because it start but I can see it in cups?
Last edited by srivo (2010-06-20 12:39:56)

a different one " hp deskjet 960c "
and use gutenprint and that should bring foomatic-db as a dependent
see the wiki
http://wiki.archlinux.org/index.php/CUPS
-- hp --
http://wiki.archlinux.org/index.php/CUP … d.22_error

Solve paper size for HP Laserjet 1102w

Similar Messages

Maybe you are looking for