[SOLVED] 2010.05 images do not ´see´ my CDROM after initial boot.

Hi, all.
I was pleased to see the new release images of 2010.05 appearing.  I thought i´d try a fresh install, but on my 800mhz machine, the installer could not see the IDE CDROM on the second part of the booting process.  I get the Arch menu and then when the installer looks for the CDROM to install Arch, it waits for 30 seconds and then can´t find it. Obviously the CD is readable because it booted initially.  I´m guessing that whichever modules are loaded for this bit of the install, it hasn´t loaded the one I need. I can confirm that the latest cut of Debian Squeeze does not have this problem.
Can anyone help?
Thanks,
Chris.
Last edited by chris_debian (2010-05-23 07:51:23)

chris_debian wrote:
Hi, all.
I was pleased to see the new release images of 2010.05 appearing.  I thought i´d try a fresh install, but on my 800mhz machine, the installer could not see the IDE CDROM on the second part of the booting process.  I get the Arch menu and then when the installer looks for the CDROM to install Arch, it waits for 30 seconds and then can´t find it. Obviously the CD is readable because it booted initially.  I´m guessing that whichever modules are loaded for this bit of the install, it hasn´t loaded the one I need. I can confirm that the latest cut of Debian Squeeze does not have this problem.
Can anyone help?
There are a few IDE controllers that are not supported properly yet by the new Linux libata subsystem. In old images, we offered an option to use the old "ide" subsystem instead of libata, support for that has been removed.
However, I doubt that you have one of the very few controllers that still don't work with libata. There is no way to tell unless you provide more details about your hardware - specifically, the mainboard chipset and/or ide controller.
A stupid, yet possible workaround: Write the image to USB too. Boot from the CD and have the USB inserted at the same time. It will start booting from the CD, but mount the file system from the USB afterwards and keep running from there.

Similar Messages

  • HT203216 Where is the Go Menu in Outlook 2010?  I do not see it anywhere.

    Where is the Go Menu in Outlook 2010?  I do not see it anywhere.

    The CSS Designer panel is a fairly new addition to DW. The version of DW you are using is older than the tutorial video by at least one version.
    There were quite a few changes between these versions...
    DWCS6 Perpetual (disk/one-time download)
    DWCS6 Cloud (subscription)
    DWCC (first one with the CSS Designer panel)
    DWCC 2014
    You really should make sure any tutorial you use matches your exact version of the program. Even if it does, updates to the cloud versions may make that information outdated in short order.

  • HP Digital Imaging Monitor not seeing Photosmart C6280 on network.

    I have put my Photosmart C6280 All-in-One printer on my wired network, and the HP Digital Imaging Monitor does not see the printer any longer.  Why?

    Hello! Could you please provide more information regarding the issue, such as which operating system you are using? Any additional information will be helpful in resolving your issue. Thanks!
    Help the community by marking this post as a solution if it solved your issue!.
    If my post helped you in any way, please click the blue KUDOS star under my name! It would mean a great deal.

  • Why does Image Capture not see my scanners?

    I have two multi-function printers - a Canon MF4350d and a HP Officejet J4550 - both connected to my iMac and both printing properly. But when
    I open Image Capture it does not see either device. How do I get my scanners functional?

    Check this thread: https://discussions.apple.com/thread/5540452?start=0&tstart=0
    It would seem there are updated drivers for (some) HP scanners.  Doesn't appear to be the case for Canon.

  • Mid 2010 Macbook Pro does not see other devices in airdrop

    Hi,
         I am able to turn on airdrop. There are no restrictions preventing me seeing other devices or them seeing me. I am unable to connect with my iPhone 5 or IPad air 2 in airdrop. Any suggestions to resolve this issue?
    Thanks,
    Andy

    There are none. A pre-2012 Mac will not see iOS devices in AirDrop.
    (119470)

  • System Image Utility not seeing Source Images.

    Ok, so I've got 10.6 server running on a New MacPro. It runs amazingly, and I love it.
    Trying to create a NetInstall service to deploy a bunch of Macs. Everything I've read says that I'll need an image of the Install, or a mounted disk that I need to create an image of. I have tried both of these scenarios and I cant seem to get anything to show up in the Sources section of System Image Utility.
    I created my custom image on an Intel MacBook Pro, and it boots without any problem. I restarted the MBPro in target disk mode, connected it to the MacPro, and created a "New Image From Disk...." in disk utility, and still it does not show up in System Image Utility.
    A stock Mac OS X install DVD in the drive shows up in the sources section, without any issue, but I really need to be able to install a customized build of the image.
    So, here's my questions:
    1) Can I create and deploy a custom 10.5 image from 10.6 server / System Image Utility II?
    2) If so, How, or what am I doing wrong?
    Desperate for help!
    Any assistance is greatly appreciated.

    I talked to Apple Support. It seems that 10.6 server can serve out 10.5< images, however each NetInstall image needs to be created with the corresponding version of System Image Utility. That is to say, if you want to create a 10.5 image to be deployed on SnowLeopard Server, you have to install 10.5.7 Server tools on a partition running 10.5, and create the image from there, then move the .nbi folder from that machine to the 10.6 server.
    Trying it now, but it seems to be working already.
    Thanks Apple Care guy!

  • Photo/Edit-In CS6. psd image does not show in LR after save/close.

    Whenever I edit (a copy) of an image in Photoshop CS6 from Lightroom 4.3 (Photo/Edit-In), after I save and close the image in CS6 the new psd image does not show in Lightroom. In order to see the image in Lightroom, I need to close Lightroom and then reopen Lightroom. It is almost like Lightroom needs to "refresh". Does anyone have a solution that does not require me to close Lightroom? I have tried to use View/Sort by extension, filename, edit time, etc. with no effect.

    This should not be so. I'm assuming that you do a <save> in CS6 - as opposed to <save as>. Only with <save> the image file will automatically be imported in Lr while <save as> creates a new file that Lr "knows" nothing about until you import it (for instance via "Synchronize folder").
    If the behavior you describe follows a <save> in CS6 it is not normal.
    This could be due to a corrupt Preference File. This file can go "funny" and is then responsible for all kinds of strange behavior of Lr. The remedy is replacing the Preference File.
    BTW: Re-installing Lr does not replace the Pref. File since it is designed to "survive" upgrades.
    See here for where to find the Preference file for your OS: http://helpx.adobe.com/lightroom/kb/preference-file-locations-lightroo m-4.html
    See here for how to go about Replacing the Preference File: http://lightroomers.com/replacing-the-lightroom-preference-file/745/

  • Can not see cFP-2220 after creating an exe file

    I am using a cFP-2220 with LabView 2011. I can see the cFP-2220 with Max, the program I created runs in my PC but the data from the cFP-2220 it is slow to up date.
    I access the cFP-2220 thru the network terminal and a net card in my PC.
    I have created an EXE file to run in the PC for that test stand as a stand along program. The program runs but it does not see the cFP-2220 or any of the data been collected. The test stand PC does have MAX install. When I run MAX in the stand PC it sees the cFP-2220 and can read the data from the modules the PC is wire to the cFP-2220 thru a net card.

    Sorry for the delay to respond... I do have installed the minimun files that are available  Field Piont 6.0.10 and LabView RT 11 is part of them.
    I also using share variables. The program VI runs fine in my PC but when I create the exe file and deploy on the test stand it asks fot the location of the FPLV,dll and the NI_TGT.dll and it can not read or write to any of the DAQmx vi's.
    I accidently remove one my FP-SG-140 from the list of inputs, I did put it back but I damage how the share variables weere working I am getting and error -1950679023 and it does not see any of my inputs.
    I have another question how do I down load the variables to the cFP-2220 that is another erros that shows up when I installed other files into the cFP.

  • Not seeing Airport Express after Leopard Upgrade

    Just upgraded by macbook to leopard, and now it's not seeing my airport express base station. the card is working fine (sees and connects to other networks) and the base station itself is connected to the internet (iphone can access it). when i turn airport off then on, system preferences will show my network as connected briefly before disconnecting, and after that i can't connect to my network again. airport utility does not see the base station.

    Perform a Factory Default Reset on the Express as follows:
    Power off the Express
    Wait a minute
    Hold in the reset button first, and keep holding for an additional 10 seconds while you plug the Express back in to power
    Release the reset button after the hold period
    Allow a full minute for the Express to restart to a slow, blinking amber light
    On the iMac running Leopard.....
    Make sure that you have the wireless turned on at the top of the screen so your Mac is connected to the network
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    When the Express appears in the window, click Continue
    Enter a name for the Express and a device password, then click Continue
    Select the option to Join your current network, then click Continue
    Select the option for the Express to wirelessly join your network and click Continue
    Click on the arrow in the drop down box and then select the name of your wireless network, or type in the name of your wireless network
    Wireless Security = WPA/WPA2 Personal
    Enter your wireless network password and verify, then click Continue
    Click Update, then click Continue
    Close AirPort Utility and wait a minute for the Express to restart. If your settings are correct, you will see a green light.
    The Express is now set up

  • Not see the apps after sync from laptop

    my iphone 4 was updated iOS 4.2. I sync apps from my laptop but after that not see a new apps into my iphone. I already reset the phone after sync. This new apps show on itune but not show on the phone. Pls help
    Message was edited by: yuhuang

    Yes.

  • HT4623 What happens if I do not see software update after clicking on the general icon?

    I am attempting to upgrade my Iphone 4 with the iOS5. software. When I go into my setting, and to general, I do not see the update software tab in my Iphone. What do I do now? How can I upgrade this software into my Iphone?
    Help
    SexyChef50

    The option to update OTA did not become available until iOS5. You will need to connect the phone to the computer and iTunes and update in that method.

  • [SOLVED] Pcmanfm and Thunar do not show pen drives after udev upgrade

    Hi all,
    I upgraded Arch today and found that my usb pen drive was not showing up in Pcmanfm available for me to mount. I reinstalled Thunar from my cache and found it too could not 'see' the pen drive. I first tried downgrading hal to the previous version, and that did not fix anything.
    I then downgraded udev to the previous version and found the usb drive correctly appearing in both file managers.
    I checked /var/log/daemon.log and found no errors. There was nothing to indicate anything had been mounted before I had downgraded udev.
    Please advise me on anything I should do--is this a bug, should I investigate further, or have I forgotten to configure something new?
    Thanks.
    added: I checked bug tracker and there seems to be a new bug related to mounting of an NTFS drive possibly due to udev. This is a FAT32 pen drive, so I am not sure if it is applicable...
    http://bugs.archlinux.org/task/11675
    added again: rebooting fixed it for me. Thank you everyone.
    Last edited by mentallaxative (2008-10-08 17:02:44)

    I noticed this happening as well after my upgrade yesterday (PCManFM and Nautilus). But then I remembered to ... reboot and everything seems happy again.
    PS: This includes VFAT, ext2 and NTFS formatted flash drives
    Last edited by ninian (2008-10-07 19:17:40)

  • Cannot see disc drive after installing boot camp windows 8

    cannot see disc drive after installing windows 8

    the superdrive,  it works fine in osx not in windows 8 on boot camp

  • Struggling with a Dell Precision T3600, Boot Image does not see Hard drive.

    Hi
    I recently got a lab of 25 of these stations in and shortly I will be imaging them. I am using the Boot Image (x86) the ones that come with sccm 2012  and I downloaded the sccm driver cab from dell and imported the storage and raid drivers into the
    boot image, yet every time I boot winpe to try to image the machine no hard drive is found.
    I followed this thread at Dell
    http://en.community.dell.com/support-forums/disk-drives/f/3534/t/19460505.aspx
    and seeming all these drivers are in the boot image (x86)
    Intel(R) C600/X79 series chipset 6-Port SATA AHCI Controller - 1D02
    Intel(R) C600 Series Chipset SAS RAID Controller
    PERC H310 for Dell Precision
    and still now hard drive seen when I boot winpe via sccm pxe.
    Does anyone have any of these machines, or any advice for me I REALLY need to solve this, I been struggling for a day so far and getting nowhere fast.
    Thanks

    Are you using the correct driver for the version of WINPE you are using?
    3.1
    Built from Windows
    7 SP1 code base. 
    4.0
    Built from Windows
    8 code base. 
    5.0
    Built from Windows
    8.1 code base. 
    So if you had a boot image based on WINPE 4.0, you would need to use a Windows 8 driver, etc.

  • Computor Not Seeing new Photos after Update

    Man I been searching for anyone having this problem. I can't find it..
    After updating my 3gs to OS4... when I plug in the phone to my Windows Xp Computer and browse to the folder for the Images... all the new ones are not there. But they are in the iPhone camera roll.
    Am I the only one that is having this issue?
    Any suggestions..

    I have a similar issue. When I go to import new photos taken with the iPhone 4 running iOS4, they cant seem to be found. What i have discovered is they are further back in the folder for some reason.
    The phone seems to be dating them in the past, so they are way back in the folder. I suggest you thoroughly browse your photo folder and see if you can't locate them somewhere in it.
    Hopefully you arent like me with nearly 4,000 photos. It's a lot of browsing......

Maybe you are looking for

  • How to deal with single quote (') in a field value?

    I can successfully insert value with single quoet using Prepared statement with placeholder(?) construct . I can also successfuly use value with single quote(') in WHERE clause. My question is, is there a way to use string with single quote if a Stat

  • Azure Backup CATALOG FAILURE 0x80131500 on Windows 8.1 Pro

    I recently installed the new Azure Backup client on a Windows 8.1 Pro computer to test the service. Every backup that is run is resulting in hundreds of skipped files showing the same error:  CATALOG FAILURE 0x80131500  A random check of some of the

  • Problems with CIF (Logical system not assign to BSG)

    Hello, We are sending all master data from ECC to APO. We set up the CIF in DEV and all worked fine. But when we try to send the data from ECC to APO in QA an error appears. It says that the logical system is not assign in the BSG. Apparently the con

  • Print too small, tried everything (I think..)

    Hi I recently installed the driver for this printer from the HP site and replaced some empty ink cartridges. So, printer now prints. Trouble is, whatever I do in Preferences, or in Word, Acrobat, anything, the page prints too small and centred. The s

  • Problems with user out of OS administrator group

    Hi! I have the following problem. I did an installation of several clients that point to a server, several months ago. The clients work with Windows 200 Professional. The installation in each client was made with a Windows user that has administrator