[SOLVED] acpi - Broadcom wireless- too many interrupts
Hi
I have an Ideapad U350:
Pentium SU4100
Chipset: GS40
My wireless card:
lspci -vnn | grep 14e4
03:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)
Subsystem: Broadcom Corporation Device [14e4:04ad]
08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe [14e4:1692] (rev 01)
iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
eth0 IEEE 802.11abg ESSID:"XXX"
Mode:Managed Frequency:2.462 GHz Access Point: XXX
Bit Rate=54 Mb/s Tx-Power=200 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=-37 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
The problem is that i have too many interrupts from acpi:
cat /proc/interrupts
CPU0 CPU1
0: 59726 61956 IO-APIC-edge timer
1: 1111 1159 IO-APIC-edge i8042
8: 1 0 IO-APIC-edge rtc0
9: 34724550 34723449 IO-APIC-fasteoi acpi
12: 555976 555190 IO-APIC-edge i8042
16: 0 0 IO-APIC-fasteoi uhci_hcd:usb2
17: 103054 104287 IO-APIC-fasteoi eth0
18: 0 0 IO-APIC-fasteoi uhci_hcd:usb7
19: 84 68 IO-APIC-fasteoi ehci_hcd:usb1, uhci_hcd:usb4, uhci_hcd:usb6
21: 0 0 IO-APIC-fasteoi uhci_hcd:usb3
23: 1 1 IO-APIC-fasteoi uhci_hcd:usb5, ehci_hcd:usb8
46: 11776 11651 PCI-MSI-edge ahci
47: 400 405 PCI-MSI-edge snd_hda_intel
48: 137735 136131 PCI-MSI-edge i915
49: 2 1 PCI-MSI-edge eth1
NMI: 1661 1673 Non-maskable interrupts
LOC: 249956 280136 Local timer interrupts
SPU: 0 0 Spurious interrupts
PMI: 1661 1673 Performance monitoring interrupts
IWI: 0 0 IRQ work interrupts
RTR: 0 0 APIC ICR read retries
RES: 303961 261227 Rescheduling interrupts
CAL: 43 84 Function call interrupts
TLB: 9561 9373 TLB shootdowns
TRM: 0 0 Thermal event interrupts
THR: 0 0 Threshold APIC interrupts
MCE: 0 0 Machine check exceptions
MCP: 14 14 Machine check polls
ERR: 0
MIS: 0
This is not a new issue, but till kernel 3.0 it could be resolved by compiling the broadcom sta driver (or using broadcom wl from AUR which is the same).
In kernel 3.0 and 3.1 the boot option 'pci=noacpi' had also to be added to minimize the interrupts.
My Laptop used to have idle power consumption of 8-9W and now it has 17W.
Because of the interrupts the CPU is never idle and the fan is constantly running.
Modules used:
lsmod|grep wl
wl 2557159 0
cfg80211 176889 1 wl
lib80211 3949 2 wl,lib80211_crypt_tkip
Powertop output:
Top causes for wakeups:
96.8% (17008.4) [acpi] <interrupt>
2.2% (387.0) PS/2 keyboard/mouse/touchpad interrupt
0.3% ( 47.7) [i915] <interrupt>
0.2% ( 29.8) swapper/1
0.1% ( 22.2) Xorg
0.1% ( 22.0) [Rescheduling interrupts] <kernel IPI>
0.1% ( 21.1) [eth0] <interrupt>
0.1% ( 18.9) swapper/0
0.1% ( 11.2) firefox
I have searched for weeks for a solution with kernel 3.3 and i have tried many boot options with acpi.
Turning acpi completely off leads to the same effect with software timer cosing the interrupts.
I have also tried the open source driver b43, which also worked but it had the same problem.
It would be great if anyone could help.
Last edited by Loch1985 (2012-05-06 19:22:47)
Yes! Thanks!
Solution:
add boot option:
acpi_os_name="Microsoft Windows NT"
REMOVE battery and boot
not sure if boot option is necessary because i removed it and its still ok....
Now it works with battery as well..
Similar Messages
-
BPC Transport Too many characteristics (024) are assigned to dimension
Hi Gurus,
We are implementing BPC Consolidation for NetWeaver 7.5, and we're facing the following situation:
Too many characteristics (024) are assigned to dimension /CPMB/Q6IW0EVD
Diagnosis
Too many characteristics are assigned to the given dimension.
For a "normal" InfoCube, the database table to be created for a dimension may contain a maximum of 249 fields. This means that no more than 248 characteristics may be assigned.
However, if the property "DIMIDs One-to-One" is set, a unique index on the characteristics of the dimension is created. In this case each dimension may not contain more than 16 characteristics.
Any suggestions?
Thanks in advance
Best Regards
Abraham MéndezHi Sheldon,
Thanks for answering my question.
I already ran that full optimization you talked about but i dont see some changes in BW, what i can see is the shadow cube that the full optimization creates but i cant see how the full optimization solves that bunching of too many BPC dimensions on one BW cube dimension afterwards.
The fact is that when the transport order generated by BPC transaction UJBPCTR is imported into the Productive environment the error still raising, with the same description:
u201CToo many characteristics (024) are assigned to dimensionu201D
Could you help me by telling me how full optimization solves that dimension bunching? Another question is Why does the error appear until the transport order is imported and not when you are working in development?
Thanks in advance.
Regards.
Abraham Mendez.
Edited by: Abraham Mendez on Apr 29, 2011 5:13 PM -
[SOLVED]Driver of Broadcom wireless-bcm43142
Hi
First I am so sorry to open a new topic while there is one in https://bbs.archlinux.org/viewtopic.php … 5#p1308505. but due to the link is solved and its solutions could not solve my problem I had to open a new one.
My problem is with my wireless device. Its driver is Broadcom wireless-bcm43142 I do not know why I cannot see my interface. The ip link gives me:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether 20:1a:06:9c:67:19 brd ff:ff:ff:ff:ff:ff
And the iwconfig gives me:
enp3s0 no wireless extensions.
lo no wireless extensions.
As you can see there is no wireless interface and wifi-menu (as root) gives:
Invalid interface specification
I have found no way to solve my problem.
Is there any one can help me?
Last edited by qaderzade (2014-12-18 10:03:35)aurabindo
dmesg did not give me that " a lot of errors telling "Unknown symbols"", and you see its output in bellow.
I recreated the ramdisk and reboot but still no difference.
dmesg output is (a little long):
# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.17.6-1-ARCH (builduser@foutrelis) (gcc version 4.9.2 (GCC) ) #1 SMP PREEMPT Sun Dec 7 23:43:32 UTC 2014
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=9cd33087-f581-4583-a7ce-7d50d414eea6 rw quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d3ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d400-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000096aaffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000096ab0000-0x0000000097eaffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000097eb0000-0x000000009cabefff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009cabf000-0x000000009cebefff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009cebf000-0x000000009cfbefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009cfbf000-0x000000009cffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000009cfff000-0x000000009cffffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009d000000-0x000000009f9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb0ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff980000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x00000001df5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: LENOVO 20238/INVALID, BIOS 79CN46WW(V3.05) 12/23/2013
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x1df600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E7FFF write-protect
[ 0.000000] E8000-EFFFF write-combining
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7F80000000 write-back
[ 0.000000] 1 base 0080000000 mask 7FE0000000 write-back
[ 0.000000] 2 base 009D000000 mask 7FFF000000 uncachable
[ 0.000000] 3 base 009E000000 mask 7FFE000000 uncachable
[ 0.000000] 4 base 00FF800000 mask 7FFF800000 write-protect
[ 0.000000] 5 base 0100000000 mask 7F00000000 write-back
[ 0.000000] 6 base 01DF600000 mask 7FFFE00000 uncachable
[ 0.000000] 7 base 01DF800000 mask 7FFF800000 uncachable
[ 0.000000] 8 base 01E0000000 mask 7FE0000000 uncachable
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0x9d000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fe1b0-0x000fe1bf] mapped at [ffff8800000fe1b0]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b2b000, 0x01b2bfff] PGTABLE
[ 0.000000] BRK [0x01b2c000, 0x01b2cfff] PGTABLE
[ 0.000000] BRK [0x01b2d000, 0x01b2dfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x1df400000-0x1df5fffff]
[ 0.000000] [mem 0x1df400000-0x1df5fffff] page 2M
[ 0.000000] BRK [0x01b2e000, 0x01b2efff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x1dc000000-0x1df3fffff]
[ 0.000000] [mem 0x1dc000000-0x1df3fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x180000000-0x1dbffffff]
[ 0.000000] [mem 0x180000000-0x1bfffffff] page 1G
[ 0.000000] [mem 0x1c0000000-0x1dbffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x96aaffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
[ 0.000000] [mem 0x80000000-0x969fffff] page 2M
[ 0.000000] [mem 0x96a00000-0x96aaffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x97eb0000-0x9cabefff]
[ 0.000000] [mem 0x97eb0000-0x97ffffff] page 4k
[ 0.000000] [mem 0x98000000-0x9c9fffff] page 2M
[ 0.000000] [mem 0x9ca00000-0x9cabefff] page 4k
[ 0.000000] BRK [0x01b2f000, 0x01b2ffff] PGTABLE
[ 0.000000] BRK [0x01b30000, 0x01b30fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x9cfff000-0x9cffffff]
[ 0.000000] [mem 0x9cfff000-0x9cffffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x17fffffff]
[ 0.000000] [mem 0x100000000-0x17fffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x37950000-0x37c9ffff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000FE020 000024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 0x000000009CFFE210 0000A4 (v01 LENOVO CB-01 00000001 01000013)
[ 0.000000] ACPI: FACP 0x000000009CFF7000 00010C (v05 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: DSDT 0x000000009CFE9000 00AE0E (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: FACS 0x000000009CFBA000 000040
[ 0.000000] ACPI: SLIC 0x000000009CFFD000 000176 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: UEFI 0x000000009CFFC000 000236 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: FPDT 0x000000009CFFA000 000044 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASF! 0x000000009CFF8000 0000A5 (v32 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: HPET 0x000000009CFF6000 000038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: APIC 0x000000009CFF5000 00008C (v03 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: MCFG 0x000000009CFF4000 00003C (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000009CFE6000 002028 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: BOOT 0x000000009CFE4000 000028 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: LPIT 0x000000009CFE3000 000094 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASPT 0x000000009CFE1000 000034 (v07 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: DBGP 0x000000009CFE0000 000034 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000009CFDF000 000539 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000009CFDE000 000AD8 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x000000009CFDA000 00348C (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x00000001df5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x1df5fffff]
[ 0.000000] NODE_DATA [mem 0x1df5f9000-0x1df5fcfff]
[ 0.000000] [ffffea0000000000-ffffea00077fffff] PMD -> [ffff8801d8c00000-ffff8801debfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x1df5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009cfff]
[ 0.000000] node 0: [mem 0x00100000-0x96aaffff]
[ 0.000000] node 0: [mem 0x97eb0000-0x9cabefff]
[ 0.000000] node 0: [mem 0x9cfff000-0x9cffffff]
[ 0.000000] node 0: [mem 0x100000000-0x1df5fffff]
[ 0.000000] On node 0 totalpages: 1551452
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 9883 pages used for memmap
[ 0.000000] DMA32 zone: 632512 pages, LIFO batch:31
[ 0.000000] Normal zone: 14296 pages used for memmap
[ 0.000000] Normal zone: 914944 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics stolen memory at 0x9da00000-0x9f9fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x96ab0000-0x97eaffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9cabf000-0x9cebefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9cebf000-0x9cfbefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9cfbf000-0x9cffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9d000000-0x9f9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9fa00000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfeafffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb10000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff97ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff980000-0xffffffff]
[ 0.000000] e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff8801df200000 s82752 r8192 d23744 u262144
[ 0.000000] pcpu-alloc: s82752 r8192 d23744 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1527188
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=9cd33087-f581-4583-a7ce-7d50d414eea6 rw quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 6025340K/6205808K available (5386K kernel code, 897K rwdata, 1712K rodata, 1136K init, 1176K bss, 180468K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS:8448 nr_irqs:488 0
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 25165824 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2394.400 MHz processor
[ 0.000028] Calibrating delay loop (skipped), value calculated using timer frequency.. 4790.33 BogoMIPS (lpj=7981333)
[ 0.000031] pid_max: default: 32768 minimum: 301
[ 0.000037] ACPI: Core revision 20140724
[ 0.010737] ACPI: All ACPI Tables successfully acquired
[ 0.015141] Security Framework initialized
[ 0.015146] Yama: becoming mindful.
[ 0.015604] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.017037] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.017660] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.017670] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.017854] Initializing cgroup subsys memory
[ 0.017859] Initializing cgroup subsys devices
[ 0.017860] Initializing cgroup subsys freezer
[ 0.017862] Initializing cgroup subsys net_cls
[ 0.017864] Initializing cgroup subsys blkio
[ 0.017883] CPU: Physical Processor ID: 0
[ 0.017884] CPU: Processor Core ID: 0
[ 0.017888] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.018805] mce: CPU supports 9 MCE banks
[ 0.018821] CPU0: Thermal monitoring enabled (TM1)
[ 0.018833] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[ 0.018930] Freeing SMP alternatives memory: 20K (ffffffff819fe000 - ffffffff81a03000)
[ 0.019643] ftrace: allocating 20687 entries in 81 pages
[ 0.027980] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.061010] smpboot: CPU0: Intel(R) Core(TM) i7-4700MQ CPU @ 2.40GHz (fam: 06, model: 3c, stepping: 03)
[ 0.061020] TSC deadline timer enabled
[ 0.061041] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.061059] ... version: 3
[ 0.061060] ... bit width: 48
[ 0.061061] ... generic registers: 4
[ 0.061062] ... value mask: 0000ffffffffffff
[ 0.061063] ... max period: 0000ffffffffffff
[ 0.061064] ... fixed-purpose events: 3
[ 0.061064] ... event mask: 000000070000000f
[ 0.084495] x86: Booting SMP configuration:
[ 0.084497] .... node #0, CPUs: #1
[ 0.098756] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.105430] #2 #3 #4 #5 #6 #7
[ 0.220589] x86: Booted up 1 node, 8 CPUs
[ 0.220592] smpboot: Total of 8 processors activated (38325.66 BogoMIPS)
[ 0.228167] devtmpfs: initialized
[ 0.230940] PM: Registering ACPI NVS region [mem 0x9cebf000-0x9cfbefff] (1048576 bytes)
[ 0.231682] pinctrl core: initialized pinctrl subsystem
[ 0.231717] RTC time: 6:10:48, date: 12/19/14
[ 0.231793] NET: Registered protocol family 16
[ 0.231888] cpuidle: using governor ladder
[ 0.231890] cpuidle: using governor menu
[ 0.231915] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.231917] ACPI: bus type PCI registered
[ 0.231918] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.231992] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.231994] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.232265] PCI: Using configuration type 1 for base access
[ 0.232504] mtrr: your CPUs had inconsistent variable MTRR settings
[ 0.232505] mtrr: probably your BIOS does not setup all CPUs.
[ 0.232505] mtrr: corrected configuration.
[ 0.244996] ACPI: Added _OSI(Module Device)
[ 0.244998] ACPI: Added _OSI(Processor Device)
[ 0.244999] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.245000] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.268870] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.269663] ACPI: Dynamic OEM Table Load:
[ 0.269671] ACPI: SSDT 0xFFFF8801D5E0F400 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120518)
[ 0.281610] ACPI: Dynamic OEM Table Load:
[ 0.281617] ACPI: SSDT 0xFFFF8801D5EC8800 0005AA (v01 PmRef ApIst 00003000 INTL 20120518)
[ 0.294842] ACPI: Dynamic OEM Table Load:
[ 0.294848] ACPI: SSDT 0xFFFF8801D5EA9C00 000119 (v01 PmRef ApCst 00003000 INTL 20120518)
[ 0.310590] ACPI: Interpreter enabled
[ 0.310598] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140724/hwxface-580)
[ 0.310604] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140724/hwxface-580)
[ 0.310620] ACPI: (supports S0 S3 S4 S5)
[ 0.310621] ACPI: Using IOAPIC for interrupt routing
[ 0.310644] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.409679] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[ 0.409684] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.409798] \_SB_.PCI0:_OSC invalid UUID
[ 0.409799] _OSC request data:1 1f 0
[ 0.409802] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[ 0.410449] PCI host bridge to bus 0000:00
[ 0.410452] pci_bus 0000:00: root bus resource [bus 00-fe]
[ 0.410454] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.410455] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.410456] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.410458] pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff]
[ 0.410465] pci 0000:00:00.0: [8086:0c04] type 00 class 0x060000
[ 0.410598] pci 0000:00:02.0: [8086:0416] type 00 class 0x030000
[ 0.410609] pci 0000:00:02.0: reg 0x10: [mem 0xb0000000-0xb03fffff 64bit]
[ 0.410615] pci 0000:00:02.0: reg 0x18: [mem 0xa0000000-0xafffffff 64bit pref]
[ 0.410619] pci 0000:00:02.0: reg 0x20: [io 0x4000-0x403f]
[ 0.410737] pci 0000:00:03.0: [8086:0c0c] type 00 class 0x040300
[ 0.410744] pci 0000:00:03.0: reg 0x10: [mem 0xb0610000-0xb0613fff 64bit]
[ 0.410894] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
[ 0.410913] pci 0000:00:14.0: reg 0x10: [mem 0xb0600000-0xb060ffff 64bit]
[ 0.410970] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.411052] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.411091] pci 0000:00:16.0: [8086:8c3a] type 00 class 0x078000
[ 0.411109] pci 0000:00:16.0: reg 0x10: [mem 0xb0618000-0xb061800f 64bit]
[ 0.411169] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.411294] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
[ 0.411315] pci 0000:00:1a.0: reg 0x10: [mem 0xb061d000-0xb061d3ff]
[ 0.411399] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.411502] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 0.411543] pci 0000:00:1b.0: [8086:8c20] type 00 class 0x040300
[ 0.411558] pci 0000:00:1b.0: reg 0x10: [mem 0xb0614000-0xb0617fff 64bit]
[ 0.411629] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.411714] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.411750] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
[ 0.411823] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.411908] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.411944] pci 0000:00:1c.1: [8086:8c12] type 01 class 0x060400
[ 0.412015] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.412100] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 0.412136] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400
[ 0.412206] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.412333] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
[ 0.412353] pci 0000:00:1d.0: reg 0x10: [mem 0xb061c000-0xb061c3ff]
[ 0.412437] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.412538] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.412578] pci 0000:00:1f.0: [8086:8c49] type 00 class 0x060100
[ 0.412784] pci 0000:00:1f.2: [8086:8c03] type 00 class 0x010601
[ 0.412801] pci 0000:00:1f.2: reg 0x10: [io 0x4088-0x408f]
[ 0.412808] pci 0000:00:1f.2: reg 0x14: [io 0x4094-0x4097]
[ 0.412816] pci 0000:00:1f.2: reg 0x18: [io 0x4080-0x4087]
[ 0.412823] pci 0000:00:1f.2: reg 0x1c: [io 0x4090-0x4093]
[ 0.412830] pci 0000:00:1f.2: reg 0x20: [io 0x4060-0x407f]
[ 0.412838] pci 0000:00:1f.2: reg 0x24: [mem 0xb061b000-0xb061b7ff]
[ 0.412874] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.412986] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
[ 0.413001] pci 0000:00:1f.3: reg 0x10: [mem 0xb0619000-0xb06190ff 64bit]
[ 0.413020] pci 0000:00:1f.3: reg 0x20: [io 0x4040-0x405f]
[ 0.413202] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.413306] pci 0000:02:00.0: [14e4:4365] type 00 class 0x028000
[ 0.413333] pci 0000:02:00.0: reg 0x10: [mem 0xb0500000-0xb0507fff 64bit]
[ 0.413472] pci 0000:02:00.0: supports D1 D2
[ 0.413474] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.413504] pci 0000:02:00.0: System wakeup disabled by ACPI
[ 0.418325] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.418331] pci 0000:00:1c.1: bridge window [mem 0xb0500000-0xb05fffff]
[ 0.418484] pci 0000:03:00.0: [1969:10a0] type 00 class 0x020000
[ 0.418566] pci 0000:03:00.0: reg 0x10: [mem 0xb0400000-0xb043ffff 64bit]
[ 0.418597] pci 0000:03:00.0: reg 0x18: [io 0x3000-0x307f]
[ 0.418873] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.418982] pci 0000:03:00.0: System wakeup disabled by ACPI
[ 0.425034] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.425038] pci 0000:00:1c.2: bridge window [io 0x3000-0x3fff]
[ 0.425042] pci 0000:00:1c.2: bridge window [mem 0xb0400000-0xb04fffff]
[ 0.472074] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *7
[ 0.472128] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.472179] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *7
[ 0.472232] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.472279] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.472325] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.472377] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.472428] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.472540] ACPI: Enabled 4 GPEs in block 00 to 3F
[ 0.472570] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.472656] vgaarb: setting as boot device: PCI:0000:00:02.0
[ 0.472657] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.472660] vgaarb: loaded
[ 0.472661] vgaarb: bridge control possible 0000:00:02.0
[ 0.472693] PCI: Using ACPI for IRQ routing
[ 0.478193] PCI: pci_cache_line_size set to 64 bytes
[ 0.478318] e820: reserve RAM buffer [mem 0x0009d400-0x0009ffff]
[ 0.478320] e820: reserve RAM buffer [mem 0x96ab0000-0x97ffffff]
[ 0.478321] e820: reserve RAM buffer [mem 0x9cabf000-0x9fffffff]
[ 0.478322] e820: reserve RAM buffer [mem 0x9d000000-0x9fffffff]
[ 0.478323] e820: reserve RAM buffer [mem 0x1df600000-0x1dfffffff]
[ 0.478404] NetLabel: Initializing
[ 0.478405] NetLabel: domain hash size = 128
[ 0.478406] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.478416] NetLabel: unlabeled traffic allowed by default
[ 0.478437] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.478442] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.480472] Switched to clocksource hpet
[ 0.484636] pnp: PnP ACPI init
[ 0.484735] system 00:00: [io 0x0680-0x069f] has been reserved
[ 0.484737] system 00:00: [io 0xffff] has been reserved
[ 0.484738] system 00:00: [io 0xffff] has been reserved
[ 0.484740] system 00:00: [io 0xffff] has been reserved
[ 0.484741] system 00:00: [io 0x1800-0x18fe] could not be reserved
[ 0.484743] system 00:00: [io 0xfd60-0xfd63] has been reserved
[ 0.484744] system 00:00: [io 0x164e-0x164f] has been reserved
[ 0.484747] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.484790] system 00:01: [io 0x0800-0x087f] has been reserved
[ 0.484792] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.484819] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.484855] system 00:03: [io 0x1854-0x1857] has been reserved
[ 0.484857] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.484903] pnp 00:04: Plug and Play ACPI device, IDs SYN2b15 SYN0700 SYN0002 PNP0f13 (active)
[ 0.484975] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.530665] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.530667] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.530668] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.530669] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.530671] system 00:06: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.530673] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.530674] system 00:06: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.530675] system 00:06: [mem 0xff000000-0xff000fff] has been reserved
[ 0.530677] system 00:06: [mem 0xff010000-0xffffffff] could not be reserved
[ 0.530679] system 00:06: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.530680] system 00:06: [mem 0x9fa20000-0x9fa20fff] has been reserved
[ 0.530682] system 00:06: [mem 0x9fa10000-0x9fa1ffff] has been reserved
[ 0.530684] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.531112] pnp: PnP ACPI: found 7 devices
[ 0.537673] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 0.537676] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 0.537677] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
[ 0.537698] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.537700] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.537701] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.537706] pci 0000:00:1c.0: BAR 14: assigned [mem 0x9fb00000-0x9fcfffff]
[ 0.537709] pci 0000:00:1c.0: BAR 15: assigned [mem 0x9fd00000-0x9fefffff 64bit pref]
[ 0.537711] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.537713] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.537722] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.537727] pci 0000:00:1c.0: bridge window [mem 0x9fb00000-0x9fcfffff]
[ 0.537731] pci 0000:00:1c.0: bridge window [mem 0x9fd00000-0x9fefffff 64bit pref]
[ 0.537737] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.537742] pci 0000:00:1c.1: bridge window [mem 0xb0500000-0xb05fffff]
[ 0.537750] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.537752] pci 0000:00:1c.2: bridge window [io 0x3000-0x3fff]
[ 0.537757] pci 0000:00:1c.2: bridge window [mem 0xb0400000-0xb04fffff]
[ 0.537765] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.537767] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.537768] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.537769] pci_bus 0000:00: resource 7 [mem 0x9fa00000-0xfeafffff]
[ 0.537771] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.537772] pci_bus 0000:01: resource 1 [mem 0x9fb00000-0x9fcfffff]
[ 0.537774] pci_bus 0000:01: resource 2 [mem 0x9fd00000-0x9fefffff 64bit pref]
[ 0.537775] pci_bus 0000:02: resource 1 [mem 0xb0500000-0xb05fffff]
[ 0.537776] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
[ 0.537778] pci_bus 0000:03: resource 1 [mem 0xb0400000-0xb04fffff]
[ 0.537797] NET: Registered protocol family 2
[ 0.537974] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.538094] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.538215] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.538230] TCP: reno registered
[ 0.538239] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.538263] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.538312] NET: Registered protocol family 1
[ 0.538325] pci 0000:00:02.0: Video device with shadowed ROM
[ 1.871621] pci 0000:00:1a.0: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 3.206035] pci 0000:00:1d.0: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 3.206238] pci 0000:03:00.0: set MSI_INTX_DISABLE_BUG flag
[ 3.206279] PCI: CLS 64 bytes, default 64
[ 3.206318] Unpacking initramfs...
[ 3.259001] Freeing initrd memory: 3392K (ffff880037950000 - ffff880037ca0000)
[ 3.259009] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 3.259011] software IO TLB [mem 0x98abf000-0x9cabf000] (64MB) mapped at [ffff880098abf000-ffff88009cabefff]
[ 3.259047] Simple Boot Flag at 0x44 set to 0x1
[ 3.259313] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[ 3.259357] microcode: CPU0 sig=0x306c3, pf=0x10, revision=0x12
[ 3.259367] microcode: CPU1 sig=0x306c3, pf=0x10, revision=0x12
[ 3.259377] microcode: CPU2 sig=0x306c3, pf=0x10, revision=0x12
[ 3.259404] microcode: CPU3 sig=0x306c3, pf=0x10, revision=0x12
[ 3.259411] microcode: CPU4 sig=0x306c3, pf=0x10, revision=0x12
[ 3.259418] microcode: CPU5 sig=0x306c3, pf=0x10, revision=0x12
[ 3.259425] microcode: CPU6 sig=0x306c3, pf=0x10, revision=0x12
[ 3.259432] microcode: CPU7 sig=0x306c3, pf=0x10, revision=0x12
[ 3.259482] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 3.259503] Scanning for low memory corruption every 60 seconds
[ 3.259747] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 3.259765] Initialise system trusted keyring
[ 3.260051] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 3.261119] zpool: loaded
[ 3.261122] zbud: loaded
[ 3.261274] VFS: Disk quotas dquot_6.5.2
[ 3.261303] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 3.261403] msgmni has been set to 11774
[ 3.261449] Key type big_key registered
[ 3.261592] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 3.261641] io scheduler noop registered
[ 3.261643] io scheduler deadline registered
[ 3.261665] io scheduler cfq registered (default)
[ 3.262062] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 3.262075] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 3.262100] vesafb: mode is 1366x768x32, linelength=5504, pages=0
[ 3.262101] vesafb: scrolling: redraw
[ 3.262102] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 3.262115] vesafb: framebuffer at 0xa0000000, mapped to 0xffffc90010e80000, using 4160k, total 4160k
[ 3.349877] Console: switching to colour frame buffer device 170x48
[ 3.437348] fb0: VESA VGA frame buffer device
[ 3.437362] intel_idle: MWAIT substates: 0x42120
[ 3.437363] intel_idle: v0.4 model 0x3C
[ 3.437364] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 3.437671] GHES: HEST is not enabled!
[ 3.437734] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.438127] Linux agpgart interface v0.103
[ 3.438182] rtc_cmos 00:02: RTC can wake from S4
[ 3.438300] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 3.438332] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs
[ 3.438342] Intel P-state driver initializing.
[ 3.438532] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.438774] TCP: cubic registered
[ 3.438992] NET: Registered protocol family 10
[ 3.439502] NET: Registered protocol family 17
[ 3.440322] Loading compiled-in X.509 certificates
[ 3.440352] registered taskstats version 1
[ 3.441426] Magic number: 10:714:165
[ 3.441569] rtc_cmos 00:02: setting system clock to 2014-12-19 06:10:51 UTC (1418969451)
[ 3.441729] PM: Hibernation image not present or could not be loaded.
[ 3.443627] Freeing unused kernel memory: 1136K (ffffffff818e2000 - ffffffff819fe000)
[ 3.443631] Write protecting the kernel read-only data: 8192k
[ 3.448299] Freeing unused kernel memory: 748K (ffff880001545000 - ffff880001600000)
[ 3.450157] Freeing unused kernel memory: 336K (ffff8800017ac000 - ffff880001800000)
[ 3.463162] random: systemd-tmpfile urandom read with 4 bits of entropy available
[ 3.480365] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS1] at 0x60,0x64 irq 1,12
[ 3.520316] ACPI: bus type USB registered
[ 3.520334] usbcore: registered new interface driver usbfs
[ 3.520343] usbcore: registered new interface driver hub
[ 3.520396] SCSI subsystem initialized
[ 3.520412] usbcore: registered new device driver usb
[ 3.527223] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.527258] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.527774] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.529927] ehci-pci: EHCI PCI platform driver
[ 3.530065] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 3.530072] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 3.530086] ehci-pci 0000:00:1a.0: debug port 2
[ 3.530898] libata version 3.00 loaded.
[ 3.534001] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 3.534014] ehci-pci 0000:00:1a.0: irq 21, io mem 0xb061d000
[ 3.542963] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 3.543106] hub 1-0:1.0: USB hub found
[ 3.543110] hub 1-0:1.0: 2 ports detected
[ 3.543320] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 3.543324] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 3.543339] ehci-pci 0000:00:1d.0: debug port 2
[ 3.547225] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 3.547235] ehci-pci 0000:00:1d.0: irq 23, io mem 0xb061c000
[ 3.556309] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 3.556437] hub 2-0:1.0: USB hub found
[ 3.556441] hub 2-0:1.0: 2 ports detected
[ 3.556672] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 3.556678] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 3.556769] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 3.556791] xhci_hcd 0000:00:14.0: irq 24 for MSI/MSI-X
[ 3.557006] hub 3-0:1.0: USB hub found
[ 3.557025] hub 3-0:1.0: 14 ports detected
[ 3.560152] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 3.560155] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[ 3.560285] hub 4-0:1.0: USB hub found
[ 3.560294] hub 4-0:1.0: 4 ports detected
[ 3.560999] ahci 0000:00:1f.2: version 3.0
[ 3.561114] ahci 0000:00:1f.2: irq 25 for MSI/MSI-X
[ 3.561137] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 3.561157] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x30 impl SATA mode
[ 3.561159] ahci 0000:00:1f.2: flags: 64bit ncq stag led clo pio slum part ems apst
[ 3.566914] scsi host0: ahci
[ 3.567156] scsi host1: ahci
[ 3.567347] scsi host2: ahci
[ 3.567467] scsi host3: ahci
[ 3.567569] scsi host4: ahci
[ 3.567677] scsi host5: ahci
[ 3.567709] ata1: DUMMY
[ 3.567710] ata2: DUMMY
[ 3.567711] ata3: DUMMY
[ 3.567712] ata4: DUMMY
[ 3.567719] ata5: SATA max UDMA/133 abar m2048@0xb061b000 port 0xb061b300 irq 25
[ 3.567722] ata6: SATA max UDMA/133 abar m2048@0xb061b000 port 0xb061b380 irq 25
[ 3.573511] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 3.849898] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 3.886651] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.887407] ata5.00: ATA-9: WDC WD10JPCX-24UE4T0, 01.01A01, max UDMA/133
[ 3.887410] ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 3.888216] ata5.00: configured for UDMA/133
[ 3.888387] scsi 4:0:0:0: Direct-Access ATA WDC WD10JPCX-24U 1A01 PQ: 0 ANSI: 5
[ 3.973973] hub 1-1:1.0: USB hub found
[ 3.974050] hub 1-1:1.0: 6 ports detected
[ 4.080133] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 4.204158] hub 2-1:1.0: USB hub found
[ 4.204235] hub 2-1:1.0: 8 ports detected
[ 4.206857] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.211266] ata6.00: ATAPI: PLDS DVD-RW DS8A9SH, EL3A, max UDMA/100
[ 4.212138] ata6.00: configured for UDMA/100
[ 4.219154] scsi 5:0:0:0: CD-ROM PLDS DVD-RW DS8A9SH EL3A PQ: 0 ANSI: 5
[ 4.236511] sd 4:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 4.236515] sd 4:0:0:0: [sda] 4096-byte physical blocks
[ 4.236531] sd 4:0:0:0: [sda] Write Protect is off
[ 4.236533] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.236547] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.251972] sr 5:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 4.251975] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 4.252099] sr 5:0:0:0: Attached scsi CD-ROM sr0
[ 4.260280] tsc: Refined TSC clocksource calibration: 2394.455 MHz
[ 4.363728] usb 3-4: new high-speed USB device number 2 using xhci_hcd
[ 4.484466] sda: sda1 sda2 sda3 sda4
[ 4.485024] sd 4:0:0:0: [sda] Attached SCSI disk
[ 4.747370] usb 3-7: new full-speed USB device number 3 using xhci_hcd
[ 4.931858] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 5.080974] usb 3-8: new high-speed USB device number 4 using xhci_hcd
[ 5.261176] Switched to clocksource tsc
[ 5.542435] random: nonblocking pool is initialized
[ 6.737889] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 7.374747] EXT4-fs (sda2): re-mounted. Opts: data=ordered
[ 8.402584] systemd-journald[180]: Received request to flush runtime journal from PID 1
[ 9.159616] mei_me 0000:00:16.0: irq 26 for MSI/MSI-X
[ 9.162354] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0C:00/input/input2
[ 9.162358] ACPI: Power Button [PWRB]
[ 9.162422] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[ 9.162455] ACPI: Lid Switch [LID0]
[ 9.162497] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 9.162500] ACPI: Power Button [PWRF]
[ 9.202130] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 9.242990] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.280404] EDAC MC: Ver: 3.0.0
[ 9.285113] thermal LNXTHERM:00: registered as thermal_zone0
[ 9.285116] ACPI: Thermal Zone [TZ00] (45 C)
[ 9.338052] EDAC ie31200: No ECC support
[ 9.364458] ACPI: Battery Slot [BAT1] (battery present)
[ 9.364565] ACPI: AC Adapter [ACAD] (off-line)
[ 9.437541] AVX2 version of gcm_enc/dec engaged.
[ 9.452250] input: Ideapad extra buttons as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input6
[ 9.480172] alx 0000:03:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [20:1a:06:9c:67:19]
[ 9.505148] snd_hda_intel 0000:00:1b.0: irq 27 for MSI/MSI-X
[ 9.611542] ACPI Warning: SystemIO range 0x0000000000004040-0x000000000000405f conflicts with OpRegion 0x0000000000004040-0x000000000000404f (\_SB_.PCI0.SBUS.SMBI) (20140724/utaddress-258)
[ 9.611546] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 9.624543] sound hdaudioC1D0: CX20757: BIOS auto-probing.
[ 9.624780] sound hdaudioC1D0: autoconfig: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker
[ 9.624782] sound hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 9.624783] sound hdaudioC1D0: hp_outs=1 (0x16/0x0/0x0/0x0/0x0)
[ 9.624784] sound hdaudioC1D0: mono: mono_out=0x0
[ 9.624785] sound hdaudioC1D0: inputs:
[ 9.624786] sound hdaudioC1D0: Internal Mic=0x1a
[ 9.624788] sound hdaudioC1D0: Mic=0x19
[ 9.625578] sound hdaudioC1D0: Enable sync_write for stable communication
[ 9.628176] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card1/hdaudioC1D0/input8
[ 9.628318] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input9
[ 9.628364] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
[ 9.632142] iTCO_vendor_support: vendor-support=0
[ 9.654572] usbcore: registered new interface driver rtsx_usb
[ 9.717317] media: Linux media interface: v0.10
[ 9.733028] alx 0000:03:00.0 enp3s0: renamed from eth0
[ 9.762463] Linux video capture interface: v2.00
[ 9.762505] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 9.762530] iTCO_wdt: Found a Lynx Point TCO device (Version=2, TCOBASE=0x1860)
[ 9.762613] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 9.766150] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (174f:114f)
[ 9.772028] input: Lenovo EasyCamera as /devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/input/input11
[ 9.772070] usbcore: registered new interface driver uvcvideo
[ 9.772071] USB Video Class driver (1.1.1)
[ 10.188776] kvm: disabled by bios
[ 10.212338] kvm: disabled by bios
[ 10.214858] [drm] Initialized drm 1.1.0 20060810
[ 10.300482] intel_rapl: Found RAPL domain package
[ 10.300487] intel_rapl: Found RAPL domain core
[ 10.300489] intel_rapl: Found RAPL domain uncore
[ 10.300491] intel_rapl: Found RAPL domain dram
[ 10.572444] [drm] Memory usable by graphics device = 2048M
[ 10.572448] checking generic (a0000000 410000) vs hw (a0000000 10000000)
[ 10.572449] fb: switching to inteldrmfb from VESA VGA
[ 10.572462] Console: switching to colour dummy device 80x25
[ 10.572521] [drm] Replacing VGA console driver
[ 10.592061] i915 0000:00:02.0: irq 28 for MSI/MSI-X
[ 10.592079] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 10.592080] [drm] Driver supports precise vblank timestamp query.
[ 10.592104] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 10.627892] [drm] VBT doesn't support DRRS
[ 10.775953] Adding 6291452k swap on /dev/sda3. Priority:-1 extents:1 across:6291452k FS
[ 10.840003] fbcon: inteldrmfb (fb0) is primary device
[ 11.012282] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: data=ordered
[ 11.396384] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.5, id: 0x1e0b1, caps: 0xd00073/0x240000/0xa0400, board id: 1695, fw id: 739436
[ 11.526095] Console: switching to colour frame buffer device 170x48
[ 11.528923] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 11.528924] i915 0000:00:02.0: registered panic notifier
[ 11.530503] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[ 11.544314] mousedev: PS/2 mouse device common for all mice
[ 11.573903] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 11.573964] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input12
[ 11.574020] [drm] Initialized i915 1.6.0 20140725 for 0000:00:02.0 on minor 0
[ 11.579445] snd_hda_intel 0000:00:03.0: irq 29 for MSI/MSI-X
[ 11.609895] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input13
[ 11.609965] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input14
[ 11.610026] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input15
[ 49.117466] alx 0000:03:00.0: irq 30 for MSI/MSI-X
[ 49.117775] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 49.118703] alx 0000:03:00.0 enp3s0: NIC Up: 100 Mbps Full
[ 49.119271] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[ 60.675960] fuse init (API version 7.23)
[ 300.529167] mce: [Hardware Error]: Machine check events logged -
I attempted to set up a new HP wireless printer. It is unstable and HP support says I have too many devices since I have a time capsule and 4 airport express either extending my network or being used for a different printer or stereos. Anyone else find that their Airport Express/Extreme interferes with a wireless printer. If so, what's the point?
I have a similar model, the HP 8500A here in the home office that I originally hooked up using wireless on an AirPort system consisting of an AirPort Extreme, Time Capsule and 2 AirPort Express devices.
The HP was originally hooked up to the "main" router using wireless as a test to see how wireless would perform. No issues with setup or performance over the first few weeks. I did eventually change the device to connect using Ethernet once I had room to move the device near the AirPort Extreme.
HP is pulling your leg with the advice about too many devices. The AirPort Extreme and Time Capsule will handle up to 50 wireless devices. In my case, I did nothing except follow the setup procedure and restart the entire network....something that I always do when I make any change to the network. -
Can't Solve the "Too Many Clients Tasks" Problem
Hello All ,
I am creating a java desktop application , and i keep getting this error message:
[Microsoft][ODBC Microsoft Access Driver] Too many client tasks.
Any way ,i googled for this error and i found that because i creates many connections with database "more than 10 i think " , and that why i get this error message ..
The problem is that i do not know how to solve it , i tried to close the connections and i still getting the same error
I searched this forum , and someone suggest to close the connections and the statements and the resultset , but still not working
this is the code
public class Database_Mangement {
private String User_ID;
private String user_name;
private String password;
private Admin_Connection c;
private Connection conn;
private Connection uni_conn;
private ArrayList<Admin_TableEntry> data;
public Database_Mangement() throws SQLException
conn = null;
uni_conn = null;
conn = DriverManager.getConnection("jdbc:odbc:smart_database");// Connect with database no 1 through ODBC
uni_conn = DriverManager.getConnection("jdbc:odbc:uni_database");//Connect with database no 2 through ODBC
data = new ArrayList<Admin_TableEntry>();
ArrayList<Admin_TableEntry> getInformation(int type)throws SQLException
Statement stm = null;
ResultSet getInfo = null;
try{
//get User Information
if(type==1)
stm = conn.createStatement();
String temp;
temp = "select * from Students";
getInfo = stm.executeQuery(temp);
else if(type==2)
stm = uni_conn.createStatement();
String temp;
temp = "select * from Students";
getInfo = stm.executeQuery(temp);
while(getInfo.next())
Admin_TableEntry tempclass = new Admin_TableEntry();
if(type==1)
{tempclass.ID = getInfo.getString("Student_ID");
tempclass.Name =getInfo.getString("Student_Name");
tempclass.balance=getInfo.getString("Student_Balance");}
else if(type==2)
tempclass.ID =getInfo.getString("Student_ID");
tempclass.Name = getInfo.getString("First_Name");
tempclass.Last_Name =getInfo.getString("Last_Name");
tempclass.haveaccount=getInfo.getBoolean("Have_SmartCard");
data.add(tempclass);
catch(Exception e)
{System.out.println(e.getMessage();}
finally
conn.close();
uni_conn.close();
stm.close();
// getInfo.close(); Please note that i get an error message when i try to close the ResultSet
//and this is the error message
// Exception in thread "main" java.sql.SQLException: ResultSet is closed
return data;
}and thank you for your time..Thanks , but it only solved the ResultSet.close() problem ,
i am still getting the Too Many Clients error
and i am closing every connection i created after the end of every function .
i think i will switch to SQl server 2008 ... Hope it will be better -
I'm not able to enrol in a iOS developer program as individual. My browser says too many redirects. I'm using the Safari Browser. Please let me know how to solve this issue.
Further to my earlier post, I have just read an entry noting that if you already own a domain name, and ask your hosting service to forward and mask your iWeb '08 created, web.mac.com site to your personal domain, chances are that due to the masking of the site on web.mac.com, Safari browsers interpret the masking as being the end of the site, and as such, just return a blank page?
This may explain the problem. However, call me old fashioned, and possibly a little naive, but surely this cannot be the problem?? It's OK in Firefox! -
[SOLVED kinda]Yet another Broadcom wireless problem - scanning
Use an old Gateway laptop with a wireless card to provide internet through NAT to my desktop computer that isn't nearby my switch. I was doing this for the longest time using WinXP on the Gateway, but since all my other computers are now running linux, I figured, hey, why not put a really sleek and sexy copy of Arch onto the Gateway, and free up some of that HD space for easier file sharing between the desktop and the rest of the network. So I installed Arch, and have run head first into how much Arch and Broadcom wireless devices do not play well together. Have spent all my time since then searching the forums, the wiki, etc, but to no avail. So going to just go ahead and finally make my own call for help via the forums here.
I've only ever ONCE seen a scan find a wireless network, and that was after my first reboot after installing arch. That was the only time. There are at all times 2-4 wireless networks in range of this computer. I'm currently on my netbook running Ubuntu to post this (typing everything in by hand, ugh), and can see 4 networks right now. The Arch laptop can't find any.
To start off with: I have read the wikis. I have searched the forums. I HAVE INSTALLED THE FIRMWARE. I've checked to make sure my card is supported, and the driver it uses is the b43, and is not supposed to be compatible with the wl driver. This is the cardbus Linksys WPC54G v1 card. I know the card itself works.
Here's the various data I'm sure will be requested of me at one point or another. This is all taken immediately after booting.
What can I try. I've probably already tried it, but I'm willing to walk through step by step with someone if they think they can help.
lspci -vnn
03:00.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)
Subsystem: Linksys WPC54G v1 / WPC54GS v1 802.11g Wireless-G Notebook Adapter [1737:4320]
Flags: bus master, fast devsel, latency 64, IRQ 10
Memory at 48000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Kernel driver in use: b43-pci-bridge
Immediately after boot if I run
dmesg (related info)
[ 7.760803] b43-pci-bridge 0000:03:00.0: enabling device (0000 -> 0002)
[ 7.769836] b43-pci-bridge 0000:03:00.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
[ 7.760856] b43-pci-bridge 0000:03:00.0: settling latency timer to 64
[ 8.217173] b43-phy0: Broadcom 4306 WLAN found (core revision 5)
[ 8.276959] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 8.278657] Registered led device: b43-phy0::tx
[ 8.278721] Registered led device: b43-phy0::rx
[ 8.278788] Registered led device: b43-phy0::radio
[ 8.278831] Broadcom 43xx driver loaded [ Features: PMNLS ]
[ 43.860080] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[ 43.921388] ADDRCONF(NETDEV_UP): wlan0: link is not ready
uname -a
Linux oms-gateway 3.2.9-1-ARCH #1 SMP PREEMPT Thu Mar 1 09:10:44 UTC 2012 i686 Intel(R) Pentium(R) III Mobile CPU 1066MHz GenuineIntel GNU/Linux
Kernel version greater than 3.2 should be able to use the version 5.100.138 Broadcom drivers.
ifconfig wlan0
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 metric 1
ether 00:0f:66:2e:b0:83 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 btes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
iwconfig wlan0
wlan0 IEEE 802.11bg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
lsmod | grep b43
b43 317649 0
mac80211 203227 1 b43
cfg80211 147716 2 mac80211,b43
ssb 42035 1 b43
mmc_core 71470 2 ssb,b43
pcmcia 31502 2 ssb,b43
iwlist wlan0 scan
wlan0 No scan results
Last edited by oldmansutton (2012-03-11 01:53:50)oldmansutton wrote:
Strike0 wrote:Whether rev 3 needs legacy or not is controversial. I assume you blacklisted b43 when trying legacy?
How about any need to blacklist when you need b43. Anything suspicious around in lsmod?
with b43, you can see me previous lsmod on the original post.
with b43legacy, the only related things I see from lsmod are b43legacy, mac80211, cfg80211, and ssb.
Wait. Hmmm....
rmmod b43
modprobe b43legacy
rmmod b43legacy
modprobe b43
lsmod |grep b43
Now bcma is showing up. But it didn't before. It just started showing up with b43 since I did the compat-wireless package. But seeing as I'm getting scans SOMETIMES now, I hesitate to call it a problem. Maybe?
Any other ideas?
It can scan ONCE. The b43 driver is obviously functional at least for a bit.
Standard network service, wicd, netcfg, etc, I've tried them all. Reinstalled from scratch twice. Looking for NEW ideas basically. I've read just about every single post about every broadcom chipset out there. I just happen to have one of these rare ones apparently.
Last edited by oldmansutton (2012-03-10 17:46:59) -
How do I solve problem that safari cannot open because of too many redirects?
How do I fix problem that safari can't open because of too many redirects?
Try clearing the browser cache and delete any cookies for that site. If that doesn't resolve it, then that's a problem with the web-site itself, so unless it is your own website, you can't fix it.
Often it's a bug in the website code that detects what device/browser you are using and it gets stuck in a re-direct loop. You could contact the website developers and inform them. -
Iwlist scan fails when there too many wireless networks
$ sudo iwlist wlan0 scan
print_scanning_info: Allocation failed
wicd uses iwlist to scan networks but iwlist fails when there are too many networks. This seems to be an old issue. Is there a fix for this?
Thanks.There's a fix yes. For wireless_tools-29 there's a patch somewhere. Or you install wireless_tools-30pre9
-
[SOLVED] BCM4313: broadcom-wl problem, I can not set any ESSID
Hi guys I'm experiencing a weird problem with my laptop wireless card, a Broadcom 4313. I have installed the broadcom-wl driver as suggested in the Wiki and everything went smoothly during the installation, I can properly load the module with modprobe
[marco@zonzock ~]$ lsmod | grep wl
wl 1944193 0
lib80211 3966 2 wl,lib80211_crypt_tkip
And checking the system log for any possible kernel error (with dmesg) I get:
wl 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
wl 0000:03:00.0: setting latency timer to 64
lib80211_crypt: registered algorithm 'TKIP'
eth1: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.60.48.36
So everything seems fine, in fact if I try a sudo iwconfig I get:
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11 ESSID:"" Nickname:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:8 Mb/s Tx-Power:24 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=5/5 Signal level=0 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
And now the weird thing, I can't choose any ESSID!!Look at this:
[marco@zonzock ~]$ sudo iwconfig eth1 essid test
[marco@zonzock ~]$ sudo iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11 ESSID:"" Nickname:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:8 Mb/s Tx-Power:24 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=5/5 Signal level=0 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
So I can't do anything...I'm stuck there, and I couldn't solve my problem even googleing around.
Just to do some further test I have tried to change the power management mode (if you look before is set to off and as you can see below I can change the mode without problems so in some way the driver is partially working
[marco@zonzock ~]$ sudo iwconfig eth1 power on
[marco@zonzock ~]$ sudo iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11 ESSID:"" Nickname:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:8 Mb/s Tx-Power:24 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Managementmode:All packets received
Link Quality=5/5 Signal level=0 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
What can I do to solve this problem?On windows 7 I can connect without problems, the laptop is new and I'm a but frustrated now..I'm not using my NVIDIA hybrid graphic card since linux support isn't provided, I wouldn't like having other problems with the wireless too...
I am sorry for the long post but I wanted to give you as many informations as I can on this problem!Thanks a lot
Last edited by Demind (2010-08-29 23:35:35)litemotiv wrote:The Broadcom driver is buggy and incomplete, you might not see the essid in ifwconfig output but it does associate. Here is my current output while i'm browsing the forums:
You are right, it's buggy and incomplete...:(
lo no wireless extensions.
wlan0 IEEE 802.11 Nickname:""
Access Point: Not-Associated
Link Quality:5 Signal level:202 Noise level:165
Rx invalid nwid:0 invalid crypt:0 invalid misc:0
eth0 no wireless extensions.
You need to be root to see your essid, if you are not root the driver does not show you all the informations...this is a problem i.e. for programs like conky.
(i've mapped eth1 to wlan0)
What is you actual problem? Are you using any kind of networkmanager?
I've solved this problem one hour ago...using other boards I could set any essid I wanted even if I didn't set any keys, with this driver in order to set the essid I need to set the key before...just for the record network manager works far better than wicd when using this driver
Thanks for your answer! -
I am having a problem getting into the App Store on my iPhone since the recent update, I have a 4s and it appears the feature tab is not working. When I try to go into the feature tab in the App Store I get a message "too many HTTP redirects" ?... Does anyone now hoe to fix this issue, the other tabs are working okay and everything is working on my iPad ?
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Runtime.exec - Too Many Open Files
System version : Red Hat Enterprise Linux 2.4.21-47.ELsmp AS release 3 (Taroon Update 8)
JRE version : 1.6.0-b105
Important : the commands described below are launched from a Web application : Apache Tomcat 6.0.10
Hello,
I'm facing a problem already known, but appearantly never really solved ??!! ;)
When I invoke many system commands with the 'Runtime.exec(...)' method, there are open files that are not released (I can see them with the "lsof" system command) .
At the end, the unavoidable "too many open files" Exception.
The lauched commands are "ssh ... " commands.
In the topics relating to this problem, the solution is always to close all Streams / threads and to explicitely invoke the method "Process.destroy()".
My problem is that this is what I do ! And I can't do more...
Here is the code :
Runtime rt = Runtime.getRuntime();
Process process = rt.exec("ssh ...");
// ProcessStreamHolder extends Thread and reads from the InputStream given in constructor...
ProcessStreamHolder errorStream = new ProcessStreamHolder(process.getErrorStream());
ProcessStreamHolder outputStream = new ProcessStreamHolder(process.getInputStream());
errorStream.start();
outputStream.start();
exitValue = process.waitFor();
try {
errorStream.interrupt();
} catch (RuntimeException e) {
logger.warn("...");
try {
outputStream.interrupt();
} catch (RuntimeException e) {
logger.warn("...");
try {
process.getInputStream().close();
} catch (RuntimeException e) {
logger.warn("...");
try {
process.getOutputStream().close();
} catch (RuntimeException e) {
logger.warn("...");
try {
process.getErrorStream().close();
} catch (RuntimeException e) {
logger.warn("...");
process.destroy();Does someone know if my code is wrong or if there's a workaround for me ?
Thanks by advance !
Richard.Don't interrupt those threads. Close the output stream first, then wait for the process to exit, then both threads reading the stdout and stderr of the process should get EOFs, so they should exit naturally, and incidentally close the streams themselves.
-
UCCX 9 - Too many transfer failures
Hello guys,
Need some help here as I get "Too many transfer failures" message when Im running the select resource step in my script. I am sure that it's not the problem with the script as it works previously. Attach also the MIVR logs and I'm highlighting the part where I think it's the cause of the issue.
6451: Feb 23 10:03:38.447 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001, TerminalConnection to Terminal: CTIP_9009 is HELD
6452: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= ConsultCallActive
6453: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= ConnCreatedEv 9009::1
6454: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= ConnConnectedEv 9009::1
6455: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlConnInitiatedEv 9009::1
6456: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= TermConnCreatedEv CTIP_9009
6457: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= TermConnActiveEv CTIP_9009
6458: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlTermConnTalkingEv CTIP_9009
6459: Feb 23 10:03:38.450 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlConnDialingEv 9009::1
6460: Feb 23 10:03:38.450 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001 Got CallCtlConnDialingEv 9009::1, events on the AddressCallObserver.
6461: Feb 23 10:03:38.453 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlConnEstablishedEv 9009::1
6462: Feb 23 10:03:38.453 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001 consultWithoutMedia gets CiscoJtapiException: 0x0(CTIERR_UNSPECIFIED)::Unspecified error
6463: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= ConnFailedEv 9009::1
6464: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlConnFailedEv 9009::1
6465: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001, ConsultCallObserver FAILED, cause: 109, callctl cause: 109
6466: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001, ConsultCallObserver():Received msg from original call Interrupted
6467: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallObservationEndedEv
6468: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:Call.transferFailed(6013, UNKNOWN) JTAPICallContact[id=0,implId=4068/1,state=STATE_ANSWERED_IDX,inbound=true,App name=HelpDesk,task=27000000001,session=5000000001,seq num=0,cn=4000,dn=4000,cgn=5010,ani=null,dnis=null,clid=null,atype=DIRECT,lrd=null,ocn=4000,route=RP[num=4000],OrigProtocolCallRef=0000000000000FE40121D1EF00000000,DestProtocolCallRef=null,TP=9009]
Appreciate your help.I can make a pretty good guess on this one having seen the situation occur many times before.
UCCX is not aware of, and doesn't really understand, the partitions and call search spaces on CUCM. When you do a select resource step, and attempt to send the call to the agent, the UCCX server will basically do a switch hook flash type supervised transfer to transfer the call to the agent.
When the transfer attempt is made, the CTI port that the caller is queued on will attempt to outdial to the agent's extension. It assumes that the agent phone is reachable, but has no way to verify this.
If the agent extension cannot be reached as a destination using the calling search space assigned to the CTI port, the transfer will fail. The agent will likely get stuck in a reserved state, or maybe even made not ready by the system. You can validate this by opening the dialed number analyzer in CUCM, and use the analyze function to dial the agent extension using the CSS assigned to your CTI ports.
Every time I've seen this problem over the years, the above issue was the problem. Check it out and see if it doesn't solve your issue.
Good luck!
-Cliff -
Hp pavillion dv9502au notebook pc broadcom wireless adpater not shown in device manager
Problem: hp pavillion dv9502au notebook pc broadcom wireless adpater not shown in device manager
System Type
hp pavillion dv9502au notebook pc
Windows editon
Windows 7 Ultimate
System
Processor AMD Turion(tm) 64 X2 Moblie Technology TL-56 1.80GHz
Installed Memory 1.00 GB (895 MB usable)
System type 32-bit Operating System
Wirless TECH
Broadcom Wireless
Problem
1. I have a switch at front left of laptop which can be slided to switch on Wireless Connections
2. IT turns red when switched off and blue when switched on as normal
3. But only thing that turns up is Bluetooth connection and no broadcom wireless connection
4. No adapter is shown in the devmgmt.msc( device manager)
5. I tried installing broadcom drivers to reslove the problem, and restarted many times for install.
6. I tried the "reset thing" after removing the battery that experts said about.
7. I was atlast forced to use Wired conneciton using ethernet( i hate it because, i can't be mobile around the house)
8. Please Help
Windows 7 Ultimate
System
Processor AMD Turion(tm) 64 X2 Moblie Technology TL-56 1.80GHz
Installed Memory 1.00 GB (895 MB usable)
System type 32-bit Operating System
Wirless TECH
Broadcom Wireless
Problem
1. I have a switch at front left of laptop which can be slided to switch on Wireless Connections
2. IT turns red when switched off and blue when switched on as normal
3. But only thing that turns up is Bluetooth connection and no broadcom wireless connection
4. No adapter is shown in the devmgmt.msc( device manager) (network adpaters shown are
NVIDIA geforce adapter, bluetooth adpaters)
5. I tried installing many broadcom drivers to reslove the problem, and restarted many times for install.
6. I tried the "reset thing" after removing the battery that experts said about.
7. I was atlast forced to use Wired conneciton using ethernet( i hate it because, i can't be mobile around the house)
Please helpYour wireless adapter is defective.
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee. -
UCCX9 - Too many transfer failures
Hello guys,
Need some help here. I'm getting this error "Too many transfer failures" when i do a reactive debug, it happens at the select resource step. I am sure that it's not the problem with the script as it's working previously. Attached the MIVR logs and a section of the logs which I think its the cause of the problem.
6451: Feb 23 10:03:38.447 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001, TerminalConnection to Terminal: CTIP_9009 is HELD
6452: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= ConsultCallActive
6453: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= ConnCreatedEv 9009::1
6454: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= ConnConnectedEv 9009::1
6455: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlConnInitiatedEv 9009::1
6456: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= TermConnCreatedEv CTIP_9009
6457: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= TermConnActiveEv CTIP_9009
6458: Feb 23 10:03:38.449 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlTermConnTalkingEv CTIP_9009
6459: Feb 23 10:03:38.450 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlConnDialingEv 9009::1
6460: Feb 23 10:03:38.450 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001 Got CallCtlConnDialingEv 9009::1, events on the AddressCallObserver.
6461: Feb 23 10:03:38.453 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlConnEstablishedEv 9009::1
6462: Feb 23 10:03:38.453 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001 consultWithoutMedia gets CiscoJtapiException: 0x0(CTIERR_UNSPECIFIED)::Unspecified error
6463: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= ConnFailedEv 9009::1
6464: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallCtlConnFailedEv 9009::1
6465: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001, ConsultCallObserver FAILED, cause: 109, callctl cause: 109
6466: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:CallID:0 MediaId:4068/1 Task:27000000001, ConsultCallObserver():Received msg from original call Interrupted
6467: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:OrigCall=CallID:0 MediaId:4068/1 Task:27000000001, ConsultEvent= CallObservationEndedEv
6468: Feb 23 10:03:38.454 SGT %MIVR-SS_TEL-7-UNK:Call.transferFailed(6013, UNKNOWN) JTAPICallContact[id=0,implId=4068/1,state=STATE_ANSWERED_IDX,inbound=true,App name=HelpDesk,task=27000000001,session=5000000001,seq num=0,cn=4000,dn=4000,cgn=5010,ani=null,dnis=null,clid=null,atype=DIRECT,lrd=null,ocn=4000,route=RP[num=4000],OrigProtocolCallRef=0000000000000FE40121D1EF00000000,DestProtocolCallRef=null,TP=9009]
Appreciate your comments.I can make a pretty good guess on this one having seen the situation occur many times before.
UCCX is not aware of, and doesn't really understand, the partitions and call search spaces on CUCM. When you do a select resource step, and attempt to send the call to the agent, the UCCX server will basically do a switch hook flash type supervised transfer to transfer the call to the agent.
When the transfer attempt is made, the CTI port that the caller is queued on will attempt to outdial to the agent's extension. It assumes that the agent phone is reachable, but has no way to verify this.
If the agent extension cannot be reached as a destination using the calling search space assigned to the CTI port, the transfer will fail. The agent will likely get stuck in a reserved state, or maybe even made not ready by the system. You can validate this by opening the dialed number analyzer in CUCM, and use the analyze function to dial the agent extension using the CSS assigned to your CTI ports.
Every time I've seen this problem over the years, the above issue was the problem. Check it out and see if it doesn't solve your issue.
Good luck!
-Cliff
Maybe you are looking for
-
Bex Report Designer - Large amount of data issue
Hi Experts, I am trying to execute (on Portal) report made in BEx Report Designer, with about 30 000 pages, and the only thing I am getting is a blank page. Everything works fine at about 3000 pages. Do I need to set something to allow processing suc
-
Unable to open "compose mail/settings/contacts" in standard view in 2 out of 3 Gmail accounts
Unable to open "compose mail/settings/contacts" in standard view in 2 out of 3 Gmail accounts. When "compose new mail" is selected "loading...." appears at the top then the page is frozen. ie you can't select inbox etc. Changing from standard to basi
-
Workflow table for approval step description
Hi Experts I'me looking for the table where i can find the approval step description for a node_id. I'm searching for NODE_DESC, in the table. I can find it by module fonction, but i really need the table. Thank you for your help. Peggy.
-
Cloning context file on db tier fails when run non-interactively
Hi all, I have a problem where cloning the DB tier context file using adclonectx.pl non-interactively using a pairsfile and noprompt fails in certain circumstances and continually returns this error Target System Port Pool [0-99] : RC-00201: Error: N
-
Alright people I am planning on installing Oracle 9i on GNU/Debian. Just wondering if there is anything that I need to do in order to have a successful install. For example: I know there are some issue related to using; mainly related to the licenses