[SOLVED] can't boot from ssd after "reset" from recovery usb flash drive

Question

I have a Twist s230u with the original Hitachi 500GB hdd, running Windows 8.1.  I want to replace the Hitachi 500GB hdd in my Twist s230u with a PNY 240GB SSD that i've purchased.
While running Windows from the Hitachi HDD drive I followed the "create a recovery drive" procedure to create a recovery usb.  Then I removed the Hitachi HDD from the s230u and installed the PNY 240 SSD in its place.  I booted the s230u from the recovery flash drive that I made.  I selected the "Reset Your PC" option and then the option to wipe all partition/files.  After the Reset completes, I try booting from the SSD but am unable to do so.  I just go back to the F12 boot menu.
I put the SSD in a drive dock attached to another computer.  Disk Management shows the partitions as follows - 
I've looked at the partitions on the SSD after the Reset - Disk Management console shows a 1000 MB Recovery partition, a 260MB EFI System partition, and a 221GB primary partition with volume label Windows8_OS.  It is not marked as Boot, Page File, or Crash Dump.
Diskpart shows an an additional 128MB Reserved partition between the EFI partition and the primary partition.
I do notice that the 10.6 Lenovo Recovery partition is not present - but I did make sure that I included that partition on the recovery key - though the files on the recovery key only use 8.03 GB for some reason.  Made the key on two different flash media.
Diskpart also shows the following for the SSD:
DISKPART> attributes disk
Current Read-only State : No
Read-only : No
Boot Disk : No
Pagefile Disk : No
Hibernation File Disk : No
Crashdump Disk : No
Clustered Disk : No
(It also looks like this when I run DISKPART from the recovery media with the SSD inside the internal drive bay of the s230u.)
When I did the Reset on the SSD in the s230u, and when I tried to boot from it - I had the Secure Boot disabled, the "Legacy Boot first" option set, etc.  
Can anyone point me in the right direction to be able to boot Windows 8.1 from this SSD in the s230u?  I've been working on this for a couple of days.
(I also tried cloning the HDD to the SDD using Minitool Partition Wizard, Macrium Reflect, Clonezilla, Acronis, etc - the SSD wouldn't boot after those clone operations either, and I thought maybe I'd have better luck with a reinstall from the USB recovery media.
(I also tried installing from a Windows 8 iso I burned to a DVD.  I got a product id mismatch message when I tried to install from that, and I was not allowed to proceed.)

Answer 1

well, I seem to have solved my own problem.  Maybe someone will learn from my mistakes.
I went into System Setup, went to the Startup tab, and changed the boot setting from "Both" to "UEFI Only".  After doing this I booted from my USB recovery drive, and Reset the PC.  After the Reset, I booted the s230u from the ssd, and I booted into a fresh Windows 8 installation.  
It seems that the Reset operation could not work properly while the boot setting was "Both" (UEFI and Legacy) and "Legacy First."
I got a clue when I looked at the contents of the EFI System Partition and there was nothing there except a Temp folder. The EFI System Partition had not been properly written by the Reset operation.  I got some helpful hints on how to see the contents of the EFI System Partition here - http://www.fixedbyvonnie.com/2013/12/how-to-repair-the-efi-bootloader-in-windows-8/#.U-Qz2_ldW7q
I've also buggered up my original HDD now, so that it won't boot to Windows now.  Now to fix that!