[SOLVED] Cannot boot from raid1 after upgrade

My system cannot boot from software raid(1) after upgrading the kernel to version 3.2.13-1. I realized then, that mkinitcpio.conf was overwritten (probably missed that in a previous upgrade). So I put back "mdadm" to HOOKS and "raid1" to MODULES. Unfortunately it didn't help. This is the boot-up screen:
Any ideas?
Last edited by dito (2012-03-28 13:10:52)

Thank you for your answer. I replaced the mdadm hook with mdadm_udev and updated my mdadm.conf. Removing the hd configuration stuff from grub then finally did the trick. Works again!

Similar Messages

Satellite A100 PSAA8E: Cannot boot from USB after Bios update

Hi
I downloaded the latest bios (v6) for my satellite a100 (psaa8e) and after updating the old bios, I noticed I can't boot from USB. Is there a way to restore the old bios or will this problem be solved?
Cheers
mo

I used to press F12 after restart and choose from USB. After downloading the bios, the system refuses to boot from the USB (external CD drive). However, if I place the same CD into the unit's CD drive, and choose boot from CD after pressing F12, the unit boots fine. This only happened after the bios update.
Thanx
Mo

[solved] cannot boot from dd usb and cannot install 64 with unetbootin

hi,
been trying to install arch for almost 24 hours now. i just cannot manage to setup USBs to boot from.
first i was using unetbootin, but when the device not found error came up i tried using the methods recommended in the wiki. however, my hp elitebook 2540p cannot boot from the usb created using dd or imagewriter. so i went back to unetbootin and figured out the error was that the syslinux.cfg file needed to have ../../ replaced by archisobasedir=arch archisolabel=KINGSTON. now however, i cannot seem to figure out how to install a 64 bit system. when i run pacstrap all packages have i686 at the end, which i assume means its the 32 bit one.
help
EDIT: ok i have now used 3 different USB sticks and run
sudo dd if=~/Downloads/archlinux-2012.07.15-netinstall-dual.iso of=/dev/sdd
on them. plugging them into the 2540p the laptop just wont boot. it wont get past the first hp screen, where i normally press esc to enter the menu so i can choose boot options. the usb just blinks and nothing happens. this same problem happens with imagewriter in windows.
Last edited by iOfWhy (2012-07-29 13:01:10)

McDoenerKing wrote:Was the usb stick mounted, when issueing the dd command?
Did you use "of=/dev/sdx1" instead of "of=/dev/sdx" for the dd command?
Which image did you use?
i wrote exactly
sudo dd if=~/Downloads/archlinux-2012.07.15-netinstall-dual.iso of=/dev/sdd
as mentioned in the edit above, the computer wont get past the hp screen where one gets the option to press the esc key... the usb just blinks and nothing happens...
EDIT:
no the usb was not mounted...
the image was checked with both sha1sum and md5sum...
EDIT2:
ok so i think i am in... i reformatted the usb with fat filesystem, and then went through the second instructions from the wiki, ie installing "Without overwriting the USB stick"... But i am still wondering why i couldnt just do the normal dd method. Is it that the hp bios cannot read certain filesystems?
Last edited by iOfWhy (2012-07-28 13:39:40)

Portege R30 won't boot from SSD after upgrade to SSD and HDD

Hi
I upgraded my Portege R30-A to add a second SSD (Crucial M550) replacing the optical drive with the new SSD with caddy.
But now the system won't boot automatically from the original SSD.
I could press F12 while turning on my laptop, and bring up the boot manual. Here I can see my original SSD and I can boot from it correctly.
In the boot order in the BIOS, I only see HDD/SSD, USB Memory, ODD .... It doesn't give me the option to choose between SSDs.
Anyway when I boot in this way I get blue screens after a while in win7.
I have tried to instal a HDD as the second disc instead os SSD and the resut is the same.
Is there anything I can do to solve this, now I have to use the second disc as an external USB disc.
Thanks,

I have experienced the same problem. (I don't know why my previous reply got deleted.)
The problem all relates to the CSM mode of Toshiba BIOS.
The solution is adding a boot partition (FAT32) on the drive that is in the original ODD spot.
Use a Windows 8 Installer (on a USB drive) to build a boot sector on that partition and direct it to the SSD where Windows 7 is installed. Then after you have done all of this, switch back to UEFI mode.
The system should be able to boot Windows 7 properly from the SSD in UEFI mode.

Portege R30 won't boot from SSD after upgrade to SSD and HDD under CSM mode

Hi
I upgraded my Portege R30-ASMBN22 to SSD (Crucial M550) and replace the optical drive by the original HDD with caddy.
In order to install Windows 7, I change the BIOS to CSM mode. But now the system won't boot automatically from the SSD. It only boot from HDD which is in the ODD spot.
I could press F12 while turning on my laptop, and bring up the boot manual. Here I can see my SSD and I can boot from it correctly. However, if I don't press F12 when it starts. It will always try to boot from HDD.
In the boot order in the BIOS, I only see HDD/SSD, USB Memory, ODD .... It doesn't give me the option to choose between SSD and HDD. Is there any other way to change the boot order among HDD and SSD?
Thanks,
Louis

Hi,
I did the same operation to my Portege R30-A-17C, and have the same problem, is there any way to boot without pushing F12 every time.
Thanks,
Pablo

Cannot restore from backup after upgrading to 6.1

I've upgraded my Iphone 4S from 5.1.1 to 6.1.
Backed it up before the upgrade and now that I want to restore my stuff it tells me that the backup is corrupt or not compatible.
Itunes on latest version.
windows 7.
Yes I've made a full restore of the phone ...
What should I do?
can't just start over ... had lots of important stuff on the backup.

I've upgraded my Iphone 4S from 5.1.1 to 6.1.
Backed it up before the upgrade and now that I want to restore my stuff it tells me that the backup is corrupt or not compatible.
Itunes on latest version.
windows 7.
Yes I've made a full restore of the phone ...
What should I do?
can't just start over ... had lots of important stuff on the backup.

Cannot open survey files from email after upgrading SAP gui to 720

Cannot open survey files attachments from email after upgrading SAP gui from 640 to 720.
Tried uninstalling & reinstalling but still error persists,
Error is : cannot split connection string: /h/server name/s/sapdp00 ( from SAP GUI security )
Please advise.

Can't say I have seen this error before but if it is pertaining to the new security module within 7.20, which are much more strict then 6.40, I would look under the SAP GUI configuration options. Focus on Security > Security settings.
There are pages and pages of rules which can be defined.
A test could be to disable all of them on an isolated machine and set them to allow and see if your problem persists. If the error is resolved, it is something in there you need to address.
Regards,
Zecher

Cannot boot from USB-DVD on HP Envy 13

Even when the USB DVD drive is selected as the primary boot device or selected as boot device after pressing ESC and F9, I cannot boot from DVD.
According to another post I have:
http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-e-g-Windows-8-and-Software/Boot-problem-but-...
I have problems booting from HDD as well, and now I also have problems booting from DVD. I have tried 3 different bootable DVDs.
Does anyone have any ideas to how the booting process could be corrupted any further and how I can regain the boot-from-DVD function? Now I cannot even run the recover DVD and recover the PCs factory settings.
However, I can still boot from HDD following the description from the other posting.
Thanks with best regards

Could you please give me the exact product number for your notebook?
If you need help finding it, you can use the following link:
http://h10025.www1.hp.com/ewfrf/wc/findModel?cc=us&dlc=en&lc=en
Thanks,
Kyle
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Portege Z830 - cannot boot from DVD

I have a Portege Z830-11F. I upgraded my machine to Windows 8 and but i didnt like it. So i decided to make a clean setup of Windows 7.
I downloaded the .iso file from internet and burned it to a DVD.
I plugged in my external DVD player, restarted, entered BIOS and changed the boot order and restarted again.
All went well and i was able to install Windows 7.
But i didn't had the drivers, (thought the OS would recognize the LAN driver at least, i was mistaken)
So i upgraded to Windows 8 again (without restarting) just to download the drivers for Windows 7.
I did so, but now i cannot boot from the DVD.
When i enter the boot order section, sometimes the DVD is listed, sometimes not.
In both cases the machine boots to Windows 8 straightly, does not allow me to boot from the DVD.
The strange thing is i was able to boot from the same DVD in the first place.
What can i do to boot from the DVD?

At first I must say that I dont understand why you didnt create recovery media before you have changed anything. Using preinstalled Toshiba recovery media creator you could create recovery USB and the whole situation would be not so complicated. This recovery image is activated but now if you install own OS version you will not be able to use product key that you got with your notebook.
Anyway, now perform complete Win8 shutdown and after doing this start notebook and use F12 to enter boot menu. Of course your external DVD must be connected before you start your notebook. it can be that external drive will be listed on USB boot option like on my U940.

I cannot view my videos after upgrading to OSX

I cannot view my videos after upgrading to OSX. Each video I try to open the message on the black background is Blocked Plug-In. In system preferences I have the latest Java but Flash Player does not upgrade to Flash 12 after numerous attempts.

HI MortenEJ,
Thanks for your responce.but already done doing "Restore factory settings" .. and when Im doing "back up from" ..
I still encounter the same problem. I have important messages in my inbox I want to keep.
I even try to upgrade to the newest version. IOS 5.0.1. but still the same..My main problem is my contacts. I dont have "+" add contact button and inside each contact.. I dont have the "edit" button..

I cannot edit my contacts after upgrading to IOS5 .

I cannot edit my contacts after upgrading to IOS5 . I can restore to factory settings but I want to keep my messages as they were.. what can I do? please someone help.. thanks in advance.

HI MortenEJ,
Thanks for your responce.but already done doing "Restore factory settings" .. and when Im doing "back up from" ..
I still encounter the same problem. I have important messages in my inbox I want to keep.
I even try to upgrade to the newest version. IOS 5.0.1. but still the same..My main problem is my contacts. I dont have "+" add contact button and inside each contact.. I dont have the "edit" button..

I lost hundreds of pictures from iPhoto after upgrading to Mavericks

I lost hundreds of pictures from iphoto after upgrading to mavericks. does anyone know why or how to retrieve them. i cannot find them on time machine either.

and
Why do you think you have lost "hundreds" of pictures?
What exactly are you seeing
You can try Back up your iPhoto library, Depress and hold the option (alt) and command keys and launch iPhoto - rebuild your iPhoto library database
LN

Cannot boot from osx or cd, help

Hi,
I have a problem. My macbook 5.1 boots only to windows, not to cd or osx. I am not sure what has happened but I think I installed the latest security update. I have a backup with time machine (osx) and vista with windows backup. I can wipe the whole disk clean (I do this only if I am absolutely sure it will work, CD is now unresponsive, what about if network fails...).
However, I cannot boot from CD, to verbose mode or to single user mode. None of the keys work (eject, c, s, v, cmd+c, cmd+v, cmd+s) anymore at startup. My installation dvd is stuck into the cd-rom. The eject button does not work in windows (otherwise the vista works perfectly). Also the refit screen has disappeared.
This problem is caused (to my knowlege) due to following actions:
1. security updade => failure to boot osx (hangs to apple-logo and shuts down)
2. recovery from time machine to 2 days old configuration (last known working)
3. current status, no cd, osx or startup buttons
This is my work computer and I need the linux (osx) part on monday. Please help.
Juha
Technical details:
- refit
- osx leopard
- macbook 5.1
- vista created with bootcamp
- timemachine 500Gb

I got the problem worked out. Now that I have the possibility to boot from cd I used the recovery from timecapsule again. Now it worked more properly. There is some issues with some programs and data (missing), but thats another story.
Last time I left the recovery program calculating the space needed (step 1) overnight, as takes a lot of time. I finished the step 2 (choose recovery date and copy the files) in the morning. I was not at the computer when it did the thing and I only saw the text 'recovery complete'.
Apparently there is a 'feature' that if you lose the connection between steps 1 and 2, the recovery program copies the network path that is empty (connection lost -> empty path). The program thinks everything is copied and gives 'recovery complete' message.
The problem is now mostly solved, some programs are not recovered. This is seen as question mark icons in the tray. Overall I have succesfully recovered from the latest security update.
Juha
P.S. My original login name has disappeared from this forum. I am the same guy as Dv3. Could some admin mark this as solved.
Message was edited by: dve_

Win 7 pro installed on hp touchsmart 320-1030, the machine cannot boot from installation DVD. Assist

I have installed Win 7 professional on hp touchsmart 320-1030 with an OEM DVD to overwrite Win 7 premium preinstalled from factory.
I want to reboot the machine with the same DVD after completing the installation, to test for possibility of reimage in case of crash. Although in bios, I specify cd\dvd as firts boot media, the machine cannot boot from installation DVD. I have 20 machines that behave this way. Can anyone assist?
Note: I had to delete all partitions on the PC before doing a fresh installation of Win 7 pro as Premium can not joing domain.

Hello,
So, you installed Window 7 Pro with a DVD, you boot with it to install the O.S, and now it does not work?
Have you tried to load the BIOS default values or even updating the BIOS?
If it had work before, cant understand why it does not work now...
Let me know.
Thanks,
I work for HP! Please remember to provide and if this helped click ON

Cannot open aperture v3 after upgrading to OS 10.6.8. Bought the upgrade online so cannot reload the software. Can you help?

Cannot open aperture v3 after upgrading to OS 10.6.8. Bought the upgrade online so cannot reload the software. Can you help?

How did you buy it online? Did you buy a registration number from the Apple Store?
Then you can download the Trial version from this link:
Aperture 3.1 Trial
and run Software Update immediately after installing.
Go to the Applications folder and delete Aperture.
Download the Aperture 3.1 Trial.
Open the Aperture Trial disc image.
Double-click the "Aperture Trial.mpkg" file.
Follow the onscreen instructions to install Aperture.
After the installation completes, choose Software Update from the Apple () menu.
Cannot open aperture v3 after upgrading to OS 10.6.8.
But what exactly is the error you get, when you try to launch Aperture? Maybe you need to do more than updating.
Regards
Léonie

[SOLVED] Cannot boot from raid1 after upgrade

Similar Messages

Maybe you are looking for