[SOLVED] Configuring SPDIF for MSI Mpower MAX

Hi people of the Arch,
I would like to play music over SPDIF, while I get no errors, I also get no sound.
I have read the Wiki here Advanced_Linux_Sound_Architecture
Also, I've been Googling and searching here on the forum, I've followed some steps but none seem to 'sound' right.
What I have not done is creating an asoundrc file with my setup, I believe that I can test if it works first, before I create such a file. Like to hear if this is right.
And I should note that I also use regular stereo out and USB headphones.
Attempt to play wav
@ThijsPC .:19:23:. {thijs}>aplay -D iec958:CARD=PCH,DEV=0 booze.wav
Playing WAVE 'booze.wav' : Unsigned 8 bit, Rate 22050 Hz, Stereo
aplay: set_params:1233: Sample format non available
Available formats:
- S16_LE
- S32_LE
Second attempt with bit-rate and new file
@ThijsPC .:19:35:. {thijs}>aplay -D iec958:CARD=PCH,DEV=0 Yamaha-SY-35-Clarinet-C5.wav -f S16_LE
Playing WAVE 'Yamaha-SY-35-Clarinet-C5.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
No error and no sound..
Third attempt with addressing using hw:0,1 and not the alias
@ThijsPC .:19:41:. {thijs}>aplay -D hw:0,1 Yamaha-SY-35-Clarinet-C5.wav -f S16_LE
Playing WAVE 'Yamaha-SY-35-Clarinet-C5.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
No error and no sound..
My motherboard:
MSI MPower Max
Receiving device:
Marantz NR1403
aplay -L
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
sysdefault:CARD=PCH
HDA Intel PCH, ALC1150 Analog
Default Audio Device
front:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
Front speakers
surround21:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
2.1 Surround output to Front and Subwoofer speakers
surround40:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Digital
IEC958 (S/PDIF) Digital Audio Output
hdmi:CARD=HDMI,DEV=0
HDA ATI HDMI, HDMI 0
HDMI Audio Output
hdmi:CARD=HDMI,DEV=1
HDA ATI HDMI, HDMI 1
HDMI Audio Output
hdmi:CARD=HDMI,DEV=2
HDA ATI HDMI, HDMI 2
HDMI Audio Output
hdmi:CARD=HDMI,DEV=3
HDA ATI HDMI, HDMI 3
HDMI Audio Output
hdmi:CARD=HDMI,DEV=4
HDA ATI HDMI, HDMI 4
HDMI Audio Output
hdmi:CARD=HDMI,DEV=5
HDA ATI HDMI, HDMI 5
HDMI Audio Output
sysdefault:CARD=P780
Plantronics GameCom 780, USB Audio
Default Audio Device
front:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
Front speakers
surround21:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
2.1 Surround output to Front and Subwoofer speakers
surround40:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
4.0 Surround output to Front and Rear speakers
surround41:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC1150 Analog [ALC1150 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC1150 Digital [ALC1150 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 8: HDMI 2 [HDMI 2]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 9: HDMI 3 [HDMI 3]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 10: HDMI 4 [HDMI 4]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 11: HDMI 5 [HDMI 5]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: P780 [Plantronics GameCom 780], device 0: USB Audio [USB Audio]
Subdevices: 1/1
Subdevice #0: subdevice #0
[edit]
Receiver was broken, replaced, config above is good.
Last edited by Thijxx (2014-11-17 07:55:21)

Try this one, v1.2B8;
https://forum-en.msi.com/index.php?topic=169759.msg1240621#msg1240621
Mine originally came with v1.1 and had no problem booting or restarting problem of holding settings above stock/auto/default.
Quote
What happens is that it will make it past the start orbs and I see the mouse with a black background and then it BSODs. The computer restarts again and then boots properly.
Usually an indicator a voltage isn't high enough. OC settings don't sound stable. Might open a thread in the OC and Undervolt forum section for help with that. I've stayed away from the DRAM Training (left it as is) and reached 2800 without any trouble. Not all IMC's are going to handle that speed though from what I've been reading. All my benchmarks so far are showing RAM speed above 1600 adds little performance value.

Similar Messages

MSI Mpower Max 4770k Help tweek it

Hi there,
this is my first seriouse MSI board in last 3years and i have encountered few problems with overclock
My Pc Specs are:
Intel 4770k
Corsair H70 with 2xNoctua 14FLX p/p
MSI Mpower Max
Kinston Hyper X DDR3 1600mhz 9-9-9-27 2x4GB
Corsair AX860
Intel SSD 510 250GB
Seagate Barracuda 3TB
Samsung F4 2TB
Corsair 650D
all day passed and i am a bit tired of seeing bios and bsods
i think i got the lazy chip help me understand it better and learn things on the way.
this is most stable i got.
Bios E7815IMS.133
CPU ratio: x44
Ratio: Fixed
Ring: x39
Vcore 1.25v Offset 0.015V
Svid comm. Enabled
from digitall i changed only CPU Vdrop to 100%
Ram set on xmp and manualy entered timings and voltage and speed 1600
With this i pass AIDA 64 stress test for 30min no problem
cinebench pass
when i open Prime95 Blend test 15min pass and bsod..
Temps were 80-85c with room 25c
Everything else in bios is set to default (auto)
Any tips how to tweek it more?
i tried x45 with settings as above i boot into windows pass cinebench but crash on aida64.
i also tryed just x46 with voltage bump up to 1.28v with offset 0.015
I will be deliding as soon as my h220 arrives and CLU.
Also is there some special USB so i can take the screenshots?
i tried all the ports different flashes also formated to FAT32 and NTFS same its saying no usb dongle..
When i put my WD 2TB HDD it recognize it but when i want to save the Screenshot it gives this message
"allocate file system resource fail"
I would post Screanshots but as i mentioned above its annoying problem..
Thanks in advance guys.
Edit:
just to see if i have lazy chip i tryed 1.3v with settings above and x47-48 wont even post.... :(
found flash that is working

ok i tryed this also
Internal VR efficiency management - disabled in screanshots its enabled
with this i am able to make 30mind aida with no crash temps a bit high but can be managed, i boot into windows with this vcore and x45 but unstable during aida 10min bsod
i boosted the voltage to 1.275 with offset 0.015v and got me 20min aida then bsod. any way i can tweek it more?

MSI MPower Max problem

Hello
I recently purchased an Z87 MPower Max and it came present with BIOS v1.1. According to the CPU sheet on the website it wasn't recommended to use that with a 4770K so I flashed 1.0 back on since 1.1 only boots with stock settings. Now I have this annoying problem of getting a BSOD every time I boot the computer for the first time.
What happens is that it will make it past the start orbs and I see the mouse with a black background and then it BSODs. The computer restarts again and then boots properly.
These are my settings:
CPU Ratio Mode - Dynamic
Adjust CPU Ratio - 42
EIST and Turbo boost -enabled
Adjusted Ring ratio - auto (39x)
Adjusted Ring Frequency - 3900Mhz
DRAM Reference Clock - Auto
DRAM Frequency - Auto
XMP - profile 2 (2400Mhz)
DRAM Timing Mode - Auto
Memory Fast boot - auto
VCCIN Voltags - 1.900V
CPU Core Voltage Mode - Adaptive
CPU Core Voltage - 1.165
CPU Core Offset mode is -
CPU Core Voltage Offset - 0.005
Is it something to do with this DRAM training? I was told to disable it but I'm not sure how to. Can someone help me?
I have verified 4.2Ghz stable with 2400Mhz RAM with AIDA64 and Prime95 when using fixed 1.15V and used AIDA64 CPU only for adaptive checking.
I have this RAM: F3-2400C10D-8GTX - its Gskill 2400Mhz DDR3 Trident X ram

Try this one, v1.2B8;
https://forum-en.msi.com/index.php?topic=169759.msg1240621#msg1240621
Mine originally came with v1.1 and had no problem booting or restarting problem of holding settings above stock/auto/default.
Quote
What happens is that it will make it past the start orbs and I see the mouse with a black background and then it BSODs. The computer restarts again and then boots properly.
Usually an indicator a voltage isn't high enough. OC settings don't sound stable. Might open a thread in the OC and Undervolt forum section for help with that. I've stayed away from the DRAM Training (left it as is) and reached 2800 without any trouble. Not all IMC's are going to handle that speed though from what I've been reading. All my benchmarks so far are showing RAM speed above 1600 adds little performance value.

MSI MPOWER MAX Z87 - RAID failure after BIOS update (settings reset)

I use the integrated intel RAID controller to create a 2 disk RAID-0 6TB (2x3TB), but everytime I update the BIOS, there is a RAID failure.
It does not matter if I use Live Update or the Update BIOS+ME option of the BIOS menu. All settings are lost, and after the boot the RAID controller is deactivated due to that. I go to BIOS right after the auto-reboot and re-enter my settings (RAID instead of AHCI), but the intel controller only sees 1 disk as a RAID member. Recovery option is not active when I enter the controller options (control+I). I always need to delete and recreate the RAID, which of course loses all data.
Very frustrating!
Am I doing the update wrong? I know I did it once and settings were not reset, my RAID was kept intact, but I believe it was only 1 time of 4 or 5 updates I did to my MPOWER MAX.

Hi, thanks for trying to help!
- I use Windows 8.1.
- My vga does not support UEFI so I use... legacy mode? (I'm not that familiar with BIOS->UEFI yet, sorry.)
- According to Intel RST, the RAID HDDs are on ports 2 and 3.
- This time the update was from 1.80 to 1.90.
1.70 to 1.80 also resulted in the same problem, but I used LiveUpdate.
For previous updates, I don't remember but I sometimes I used LiveUpdate, sometimes the BIOS feature.
I'm pretty sure that only once the RAID was kept intact, and I don't remember the versions or method I used, but I believe I used the BIOS method (don't know if needed BIOS+ME or not), not LiveUpdate.

MOVED: MSI mpower Max z87 problems

This topic has been moved to Intel Core-iX boards.
https://forum-en.msi.com/index.php?topic=172963.0

What is the S/N of the 760?
We will need to update the Vbios for GOP support most likely.
The most recent MPOWER bios I just posted here as well. >>BIOSes<<

MSI mpower Max z87 problems

I have 2 problems with my MSI board
1) When I Insert my MSI 760gtx card on the 1st SLI slot the computer does not boot to windows and I get a random A? something error A6 A0 depents on what it decides but on the second slot works fine
2) Secondly when I try windows 8 fast boot it says that I have not a windows 8 logo graphic card I have the MSI 760gtx and it supports windows 8 as it says on the box how do I fix that issue ?
thanks for reading

What is the S/N of the 760?
We will need to update the Vbios for GOP support most likely.
The most recent MPOWER bios I just posted here as well. >>BIOSes<<

MSI Mpower Max and Team Group LV 2400 Memory (Samsung)

Bios 1.31b is fine, but afterwards seems to have a problem with my memory modules, even at XMP settings they are difficult to boot. I am pretty sure it is related to a single value called tWR. For some reason the tWR value in the later bios are limited to be adjusted between 0 and 16. My modules need it to be 18 to boot at XMP.
I really want those later bioses, because of the faster PWM and the Legacy optimizing for benching. Please tell me where to post these to get my memory modules working.

If you want to report an issue you found contact MSI: >>How to contact MSI.<<
This is a Users-to-Users Forum. MSI creates the beta versions.

MOVED: MSI MPOWER MAX W10 Soundblaster Cinema

This topic has been moved to MSI Intel boards.
https://forum-en.msi.com/index.php?topic=256499.0

Hi
1: >>Posting Guide<<
2: Not many drivers are ready yet for Windows 10 which is not released. Be patient until Windows 10 release (29Th July), and by then most drivers and software should be updated and compatible with Win10.

Msi MPower MAX AC Power Saver Question

In the msi bios how do you enable the power saving feature so when the pc is idle or under light load it throttles down to 1.6 ghz.I am using offset now 4.7 with +35 offset for 1.264volts.Any help appreciated.

i think he wanted freq. to drop when the CPU is in idle
if this is correct you need to enable "EIST" and "C-State" states
also you can try switching within windows power profile to "Balanced"
[in some machines when its set to high performance this prevent CPU freq. throttling at idle]

BIOS download bad for Z87 MPower Max

The latest BIOS update for this motherboard (MS-7815) is bad from the downloads section - when attempting to run it, I get a message stating it is not for my version of Windows (7 x64). Trying through Live Update and the download aborts.
I hope Support fixes this.

Quote
The download from the website works. As I mentioned in my first post, the executable does not work with Windows 7 x64 - it clearly says: 'This version of this file is not compatible with the version of Windows you're running'. There is no option on the web page for downloading a version based on the version of Windows.
that's not issue, the flasher included is for pure DOS
there is no Windows flasher.
if you download it manually from MSI web page,
you have or flash it from pure DOS
or from M-Flash from BIOS setup

MSI MPower Max Command Center Error ver. 1.0.0.59

Hi everyone! I apologise in advance for my poor English.
I was very pleased with my new PC (and also with the motherboard!) until command center made me upgrade to ver. 1.0.0.59. Every time I open it I get this error message and sometimes (1 on 4 sessions) it significantly lowers CPU's clock.
The part in Italian says: " It's impossible to find part of the directory ...... \LU5_LMU.xml"
How would you fix it? Should I reinstall the previous version and, in that case, where can I download it from?
Thanks for your help,
Gilberto

here http://www.msi.com/product/mb/Z87_MPOWER_MAX.html#download
and click on utility

MSI MPOWER MAX W10 Soundblaster Cinema

Hi, i cant get the soundblaster software to work under W10 Build 10130. Does anybody else have this Problems and is there a fix?

Hi
1: >>Posting Guide<<
2: Not many drivers are ready yet for Windows 10 which is not released. Be patient until Windows 10 release (29Th July), and by then most drivers and software should be updated and compatible with Win10.

Z87 MSI Mpower Max Adaptive vcore not working properly?

Hi, first time MSI MB user here.
After I finished tweaking my OC settings, I changed the vcore voltage from fixed to adaptive mode, since that is said to lower the idle temps.
However, it doesn't seem to work in the way that I thought it would.
Vcore voltage stays at the same value regardless of whether the CPU is idle or under load. I thought it would lower itself when the CPU is idle.
Am I misunderstanding something here?
Voltage check done by AIDA64 and CPU-Z 1.64.3
Below are my bios settings:
BIOS ver. 1.1
CPU Ratio Mode - Dynamic
Adjust CPU Ratio - 45
EIST and Turbo boost -enabled
Adjusted Ring ratio - auto (39x)
Adjusted Ring Frequency - 3900Mhz
VCCIN Voltags - 1.95V
CPU Core Voltage Mode - Adaptive
CPU Core Voltage - 1.25
Thanks.

Quote
Once the CPU V. is taken out of auto and set manually, the voltage isn't going to drop at idle.
Quote
That's not what I was led to believe?
Yup! Turns out your belief is correct. The rules 'have' changed with Z87!

Msi Mpower Max AC Z97 Watercooling Question

I have a Swiftech H240x watercooler hooked up and wonder when I try to controll the swiftech cpu pump on manual its all greyed out under 75 %,when i move it to 75 from 100 the pump speed is still running at 100%.The only way I can run the pump slower is in smart mode and move it to 26% and it gives me 1600 rpm pump speed,not 3000 at 100 .Is this normal not to have the manual pump speed work and have it greyed out under 75% with only smart mode working.Just wondering why smart mode is a no go for me.Any help appreciated..Oh ya,my rad fans,and case fans also no go in manual mode,but can be adjusted in smart mode.

I am useing a NZXT Sentry 3 now to control all fans in my pc.Works darn good,looks good too.Just the Swiftech H240x watercooler is hooked up to the mb.I still can not make manual mode work to adj the waterpump.It stayes at 100% no matter where I put the ajuster,and all greyed out below 75%.To control the adjustable swiftech waterpump the rpm's are at lowest 1200 rpm and the highest is 3000 rpm.I have the waterpump pluged in to cpu fan-1.Is this not the right spot to hook it up to.If anyone has ideas for me to try to get manual control working please let me know.

Msi Mpower Max AC Z97 Bios Screen

Has anyone upon roboot and entering the bios have the bios screen go all distorted looking weird.I hit the reset button on my case it reboots and all is fine after.Just noticed that it has been doing this 3-4 time a week.Curious on what causes this.

too possible bios bug
what bios version you are using?
also list full system specs, see >>Posting Guide<<

[SOLVED] Configuring SPDIF for MSI Mpower MAX

Similar Messages

Maybe you are looking for