[SOLVED]Getting Dual Monitors To With Nvidia Cards Under Arch
Just got a second monitor and I am trying to set it up to work with arch.
I have 2 nvidia cards with 1 monitor plugged into each.
Reading through the wiki: https://wiki.archlinux.org/index.php/DualScreen
When I try
xrandr -q
after downloading and installing:
pacman -S xorg-xrandr arandr
I get the message:
RandR extension missing
So not sure what is going on here... (***EDIT: Worked after rebooting***)
Output for:
xrandr -q
is:
Screen 0: minimum 8 x 8, current 1920 x 1200, maximum 16384 x 16384
DVI-I-0 disconnected primary (normal left inverted right x axis y axis)
DVI-I-1 disconnected (normal left inverted right x axis y axis)
DVI-I-2 connected 1920x1200+0+0 (normal left inverted right x axis y axis) 518mm x 324mm
1920x1200 60.0*+
1920x1080 50.0
1680x1050 60.0
1600x1200 60.0
1440x900 75.0 59.9
1280x1024 75.0 60.0
1280x960 60.0
1280x800 59.8
1280x720 60.0 50.0
1152x864 75.0
1024x768 75.0 70.1 60.0
800x600 75.0 72.2 60.3 56.2
720x576 50.0
720x480 59.9
640x480 75.0 72.8 59.9
HDMI-0 disconnected (normal left inverted right x axis y axis)
DVI-I-3 disconnected (normal left inverted right x axis y axis)
The above indicates, I believe, that arch is not seeing my second monitor...
However, it does see both monitors when I plug them both into 1 card:
Screen 0: minimum 8 x 8, current 1920 x 1200, maximum 16384 x 16384
DVI-I-0 disconnected primary (normal left inverted right x axis y axis)
DVI-I-1 disconnected (normal left inverted right x axis y axis)
DVI-I-2 connected 1920x1200+0+0 (normal left inverted right x axis y axis) 520mm x 320mm
1920x1200 60.0*+
1920x1080 50.0
1680x1050 60.0
1600x1200 60.0
1440x900 75.0 59.9
1280x1024 75.0 60.0
1280x960 60.0
1280x800 59.8
1280x720 60.0 50.0
1152x864 75.0
1024x768 75.0 70.1 60.0
800x600 75.0 72.2 60.3 56.2
720x576 50.0
720x480 59.9
640x480 75.0 72.8 59.9
HDMI-0 disconnected (normal left inverted right x axis y axis)
DVI-I-3 connected (normal left inverted right x axis y axis)
1920x1200 60.0 +
1600x1200 60.0
1280x1024 60.0
1280x960 60.0
1024x768 60.0
800x600 60.3 56.2
640x480 59.9
Since I have 2 gfx cards the card info is:
02:00.0 VGA compatible controller: NVIDIA Corporation GF114 [GeForce GTX 560 Ti] (rev a1)
03:00.0 VGA compatible controller: NVIDIA Corporation GF114 [GeForce GTX 560 Ti] (rev a1)
Since I am using 2 different cards I am supposed to add:
Section "Device"
Identifier "Screen0"
Driver "nvidia"
BusID "PCI:02:00.0"
EndSection
Section "Device"
Identifier "Screen1"
Driver "nvidia"
BusID "PCI:03:00.0"
EndSection
To:
/etc/X11/xorg.conf.d/10-monitor.conf
Section "ServerLayout"
Identifier "DualSreen"
Screen 0 "Screen0"
Screen 1 "Screen1" RightOf "Screen0" #Screen1 at the right of Screen0
Option "Xinerama" "1" #To move windows between screens
EndSection
Section "Monitor"
Identifier "Monitor0"
Option "Enable" "true"
EndSection
Section "Monitor"
Identifier "Monitor1"
Option "Enable" "true"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
Screen 0
EndSection
Section "Device"
Identifier "Device1"
Driver "nvidia"
Screen 1
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
Option "TwinView" "0"
SubSection "Display"
Depth 24
Modes "1280x800_75.00"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "Device1"
Monitor "Monitor1"
DefaultDepth 24
Option "TwinView" "0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
I am not clear on how to merge these two snippets together properly...
To be honest I am somewhat confused about this whole process... If anyone has a more clear link or can explain the steps better to me I would greatly appreciate it. Maybe I just have to read through it a few more times. Thanks in advance.
Last edited by soulrainX (2013-05-07 13:17:38)
This is how I have it thus far:
/etc/X11/xorg.conf.d/10-monitor.conf
Section "ServerLayout"
Identifier "DualSreen"
Screen 0 "Screen0"
Screen 1 "Screen1" RightOf "Screen0" #Screen1 at the right of Screen0
Option "Xinerama" "1" #To move windows between screens
EndSection
Section "Monitor"
Identifier "Monitor0"
Option "Enable" "true"
EndSection
Section "Monitor"
Identifier "Monitor1"
Option "Enable" "true"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
BusID "PCI:02:00.0"
Screen 0
EndSection
Section "Device"
Identifier "Device1"
Driver "nvidia"
BusID "PCI:03:00.0"
Screen 1
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
Option "TwinView" "0"
SubSection "Display"
Depth 24
Modes "1920x1200_75.00"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "Device1"
Monitor "Monitor1"
DefaultDepth 24
Option "TwinView" "0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
Similar Messages
-
Is a dual monitor setup with 2graphic cards possible?
HI.
What i want to do is run Archlinux on my Desktop but i dont want to miss my second monitor.
I could use both monitor on my nvidia graphiccard but i want to use the energy saving features too (wich dont work with 2monitor on one card) therefore my windows setup is big monitor on nvidia and the smaller one on the intel onboard card.
They both get recognized by lspci but only the onboard cards isy being used (the onboard card is the first card on windows too).
So is it possible to get it to work? Id really want to use ARchlinux on my Desktop too but i dont want to use it with one screen or without energy saving?
Working compositing is a must, i want to use gnome3 wich is the only reason to swich to linux for the Desktop (arch is running on the laptop for ages^^) but i dont need to, Win7 is working flawlessly fine and i didnt have to pay for it (msdnaa).
Thanks in advance!hy do you need to clock down your card?
Most gpu have a function that clocks down the card@idle and or desktop.
In my case thats down from 850mhz(560ti)to 200mhz while using windows and 50mhz if the gpu load is low.
Thats about 20watts less then with full clock.
The problem is, that the gpu wont clock down with 2monitors on it, it stays at 850mhz.
Theres some driver tweaks for amd cards wich "fix" thatfix this (i believe its intentionl, 2monitors equals more load but its no problem with new cards...
Thats one reason i use my onboard gpu for the second monitor, it works well with windows and also means that swiching off fullscreen (games) to the desktop works a lot better, the second monitor can play a movie while playing wich doesnt work with one gpu and fullscreen.
I really dont need that with Linux since i use it for work and multimedia only but the energy saving feature is nice if the pc is on 8hours and more wich is often the case.
Can you tell which one do you run? I'm going to buy one for dual-monitor setup, and I'm looking for something that will work for shure.
As said dual monitor on one gpu works, amd can do 3monitors while nvidia can do 2 at once, that means if u intend to use 3monitors some day with ur card u have to buy an amd card.
i took the nvidia because is can use it to render videos with cuda support (its not working with all tools yet but its getting better and if it works its a lot faster then my cpu rendering).
PS: Thats one hread about the power saviing with 2monitors:http://forums.nvidia.com/index.php?showtopic=197557
since my monitors dont share the same resolution it seems that theres no way to make it work .
Last edited by halfzware (2011-05-12 21:17:41) -
Downsampling with NVIDIA Cards on Arch Linux
Hello,
some of you might be familiar with downsampling already. Basically it's forcing a higher resolution
onto your screen trough the graphics driver. It is used in games as an brute-force anti-aliasing technique.
How can this be done in Linux? I'm using the latest NVIDIA 290.10 driver and a resolution of 1280x800
on my 5 years old laptop. 1680x1050 would also be an 8:5 ratio and much more practical and nicer to the eye.
My main motivation is a larger screenspace. I don't want to improve the quality of any games.
Anyone has any experience with this?
Regards,
blackout23
Last edited by blackout23 (2012-01-29 19:19:29)netcfg is deprecated, you should be using netctl.
https://www.archlinux.org/news/netctl-is-now-in-core/ -
[SOLVED]fluxbox,dual monitor apps without DISPLAY command
Hello, i use a dual monitor system with nvidia videocard, i don't use xinerama and twinview i use they as 2 different displays.
Recently i updated my arch system and now i can't start applications on the second screen just selecting and clicking on menu, but i have to use the command DISPLAY=:0.1 before the app name.
Before the system update i was able to run applications just selectin it from menu and they started in the monitor where the menu was called!!!
FYI i use fluxbox git, i just update it.
Any ideas?
Thanks in advice!
Last edited by Xeo84 (2010-12-18 18:36:39)As reporteed here:
http://www.gossamer-threads.com/lists/g … ser/222370
is a bug of libX11, i downgraded to 1.3.5 and it's solved -
Dual monitor setup with seperate resolutions
hey guys!
i currentley run thye latest version of archlinux with the cinnamon desktop environment and an nvidia geforce 7300SE graphics card.
im running a dual monitor setup with one 27" 1920x1080 monitor and one 27" 1024X768 monitor
because they have the same physical size they line up perfectley but because the resolution is different programs/mouse cursor movement doesnt, is there any way (without changing the resolutions) to compensate this effect so that in the eyes of linux/cinnamon the monitors line up so that for example dragging a window goes seamlessley between the 2 monitors.
i HAVE found out the panning option in the nvidia x server settings, but that really isnt what i am looking for...
Last edited by RikSolo (2014-08-04 11:25:02)A magnifier following the window down to the pixel, zooming to the exact size of 540 pixels the 384 pixels window could create an illusion of just that. It would be highly impractical however, not mention all the hacking time. Even if you would manage to get two screen with different sized icons, so that they match visually, the windows and fonts resizing on the fly, wmctrl might help with windows alone, no their themes (buttons, borders thickness etc.), you would still be left with a visually differently sized mouse cursor. Technically such a feat should be possible, but who is going to code it? Nvidia?
Last edited by emeres (2014-08-04 18:48:59) -
Seeking a clear description of getting dual monitors to work
I've spent a long while researching the issue of getting dual monitors to work on a new mac mini - which I will be purchasing as soon as I figure this one out! But I am bamboozled by references to the various types of connections and ports. If anyone has the patience to explain this really simply and clearly, I'd be very grateful.
Interestingly, the Apple guy on the phone today told me it isn't possible - it's either/or for the display connections. But clearly it IS possible, because there is so much discussion about it here...
Here's where I confess my technical limitations, and say that I am confused about what I need (to purchase, presumably) to get my two existing monitors to work with the new mini.
They are presently connected to my PC (soon to be ceremonially consigned... etc) with cables which have regular D-sub connectors at each end. This means they are vga, right? There is no digital connector on either monitor.
So I am trying to figure out
a) is it possible to use these two monitors in a dual display setup with a mac mini? If so:
b) How?! And then;
c) what leads and/or connectors do I need to buy in order to connect them up?
Thanks for being here, I hope for some patient guidance.
JeffWelcome to the Apple Discussions!
An '09 Mac mini has two video out pots on the rear; a mini-DVI port and a mini-DisplayPort. The Mac mini comes with a mini-DVI to DVI-D adapter. If you use what came in the box with the mini, you need a DVI-D to VGA cable to connect one of your monitors. Otherwise you need a mini-DVI to VGA adapter and a VGA to VGA cable for one monitor. For the other monitor you need a mini-DisplayPort to VGA adapter and a VGA to VGA cable.
Dah•veed -
Dell Optiplex 780 standard size tower PC dual monitor display port graphic cards
Yes, only my boss informed me that they have to be display ports, he didn't tell me why.
I'm unable to buy from ebay or craiglist either & my local vendor doesn't have any in stock.Quite a mouthful I know! but I need these specific graphic cards, ideally with next day delivery:
Dell Optiplex 780 standard size tower PC (Non SFF) dual monitor display port graphic cards
Any recommendations? I can find 2 on amazon (UK) I need 3!
This topic first appeared in the Spiceworks Community -
Does LR handle a dual monitor setup with different aspect ratios (16:9 and 16:10)?
Does LR 5 handle a dual monitor setup with different aspect ratios (16:9 and 16:10)?
I'm planing to buy a 27" 16:9 monitor and use it as primary together with a 22" 16:10. Does any have any idea?
ThanksMoreover, the two monitors can have completely different characteristics. As always, you really need to calibrate/profile any monitor (with a hardware tool - Spyder, Colormunki etc). That's no more important with two monitors, but you see for sure if you don't, as two dissimilar monitors will then probably look different.
-
[SOLVED] Trying to get dual monitor Xrandr to run on startup
I found several posts with trying to get an Xrandr script on startup but their solution doesn't seem to work.
Running Arch + XFCE + SLiM with ati open source drivers
when running xrandr --output HDMI-0 --right-of DVI-1 in terminal my dual monitor setup works fine
so I add it to my /home/username/.xinitrc which looks like
xrandr --output HDMI-0 --right-of DVI-1
exec ck-launch-session startxfce4
but there is the same ol' mirrored desktops? Any suggestions?
Last edited by PumpkinJack (2011-08-16 02:12:17)It could also be me overlooking some stupid simple detail too. I haven't had any issues with gnome or kde but granted I could use the actual gui
to change it. Weird thing is when I installed xfce a couple days ago I swear it had a gui to enable what I need because also it WAS working 2 days ago o_O
but heres the log:
[ 2985.229]
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
[ 2985.239]
X.Org X Server 1.10.3.901 (1.10.4 RC 1)
Release Date: 2011-07-29
[ 2985.244] X Protocol Version 11, Revision 0
[ 2985.245] Build Operating System: Linux 3.0.0-ARCH x86_64
[ 2985.247] Current Operating System: Linux sfx 3.0-ARCH #1 SMP PREEMPT Sat Aug 6 16:18:35 CEST 2011 x86_64
[ 2985.249] Kernel command line: root=/dev/disk/by-uuid/8b947b8e-d3af-467a-ac97-057e0e474832 ro
[ 2985.250] Build Date: 08 August 2011 08:24:13AM
[ 2985.252]
[ 2985.254] Current version of pixman: 0.22.2
[ 2985.255] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 2985.259] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 2985.264] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Aug 15 14:19:05 2011
[ 2985.265] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 2985.267] (==) No Layout section. Using the first Screen section.
[ 2985.267] (==) No screen section available. Using defaults.
[ 2985.267] (**) |-->Screen "Default Screen Section" (0)
[ 2985.267] (**) | |-->Monitor "<default monitor>"
[ 2985.267] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 2985.267] (**) | |-->Device "mycard"
[ 2985.267] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 2985.267] (==) Automatically adding devices
[ 2985.267] (==) Automatically enabling devices
[ 2985.267] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 2985.267] Entry deleted from font path.
[ 2985.267] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 2985.267] Entry deleted from font path.
[ 2985.267] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 2985.267] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 2985.267] Entry deleted from font path.
[ 2985.267] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 2985.267] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 2985.267] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 2985.267] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 2985.267] (II) Loader magic: 0x7d3620
[ 2985.267] (II) Module ABI versions:
[ 2985.267] X.Org ANSI C Emulation: 0.4
[ 2985.267] X.Org Video Driver: 10.0
[ 2985.267] X.Org XInput driver : 12.2
[ 2985.267] X.Org Server Extension : 5.0
[ 2985.268] (--) PCI:*(0:3:0:0) 1002:6738:1682:3100 rev 0, Mem @ 0xd0000000/268435456, 0xfbcc0000/131072, I/O @ 0x0000c000/256, BIOS @ 0x????????/131072
[ 2985.268] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 2985.268] (II) LoadModule: "extmod"
[ 2985.269] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 2985.269] (II) Module extmod: vendor="X.Org Foundation"
[ 2985.269] compiled for 1.10.3.901, module version = 1.0.0
[ 2985.269] Module class: X.Org Server Extension
[ 2985.269] ABI class: X.Org Server Extension, version 5.0
[ 2985.269] (II) Loading extension MIT-SCREEN-SAVER
[ 2985.269] (II) Loading extension XFree86-VidModeExtension
[ 2985.269] (II) Loading extension XFree86-DGA
[ 2985.269] (II) Loading extension DPMS
[ 2985.269] (II) Loading extension XVideo
[ 2985.269] (II) Loading extension XVideo-MotionCompensation
[ 2985.269] (II) Loading extension X-Resource
[ 2985.269] (II) LoadModule: "dbe"
[ 2985.269] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 2985.269] (II) Module dbe: vendor="X.Org Foundation"
[ 2985.269] compiled for 1.10.3.901, module version = 1.0.0
[ 2985.269] Module class: X.Org Server Extension
[ 2985.269] ABI class: X.Org Server Extension, version 5.0
[ 2985.269] (II) Loading extension DOUBLE-BUFFER
[ 2985.269] (II) LoadModule: "glx"
[ 2985.269] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 2985.269] (II) Module glx: vendor="X.Org Foundation"
[ 2985.269] compiled for 1.10.3.901, module version = 1.0.0
[ 2985.269] ABI class: X.Org Server Extension, version 5.0
[ 2985.269] (==) AIGLX enabled
[ 2985.269] (II) Loading extension GLX
[ 2985.269] (II) LoadModule: "record"
[ 2985.269] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 2985.269] (II) Module record: vendor="X.Org Foundation"
[ 2985.269] compiled for 1.10.3.901, module version = 1.13.0
[ 2985.269] Module class: X.Org Server Extension
[ 2985.269] ABI class: X.Org Server Extension, version 5.0
[ 2985.269] (II) Loading extension RECORD
[ 2985.269] (II) LoadModule: "dri"
[ 2985.269] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 2985.269] (II) Module dri: vendor="X.Org Foundation"
[ 2985.269] compiled for 1.10.3.901, module version = 1.0.0
[ 2985.269] ABI class: X.Org Server Extension, version 5.0
[ 2985.269] (II) Loading extension XFree86-DRI
[ 2985.269] (II) LoadModule: "dri2"
[ 2985.269] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 2985.270] (II) Module dri2: vendor="X.Org Foundation"
[ 2985.270] compiled for 1.10.3.901, module version = 1.2.0
[ 2985.270] ABI class: X.Org Server Extension, version 5.0
[ 2985.270] (II) Loading extension DRI2
[ 2985.270] (II) LoadModule: "radeon"
[ 2985.270] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
[ 2985.270] (II) Module radeon: vendor="X.Org Foundation"
[ 2985.270] compiled for 1.10.1, module version = 6.14.2
[ 2985.270] Module class: X.Org Video Driver
[ 2985.270] ABI class: X.Org Video Driver, version 10.0
[ 2985.270] (II) RADEON: Driver for ATI Radeon chipsets:
ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
ATI Radeon Mobility X300 (M24) 3152 (PCIE),
ATI FireGL M24 GL 3154 (PCIE), ATI FireMV 2400 3155 (PCI),
ATI Radeon X600 (RV380) 3E50 (PCIE),
ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
ATI Radeon 8500 AIW BB (AGP), ATI Radeon IGP320M (U1) 4336,
ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
ATI Radeon X800PRO (R420) JI (AGP),
ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
ATI Radeon Mobility 9800 (M18) JN (AGP),
ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
ATI Radeon 9800XT NJ (AGP),
ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
ATI Radeon Mobility X300 (M22) 5460 (PCIE),
ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
ATI Radeon X800PRO (R423) UI (PCIE),
ATI Radeon X800LE (R423) UJ (PCIE),
ATI Radeon X800SE (R423) UK (PCIE),
ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
ATI FireGL unknown (R423) UR (PCIE),
ATI FireGL unknown (R423) UT (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility FireGL V5000 (M26) (PCIE),
ATI Mobility Radeon X700 XL (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Mobility Radeon X700 (M26) (PCIE),
ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835,
ATI Radeon XPRESS 200 5954 (PCIE),
ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
ATI Radeon XPRESS 200M 5975 (PCIE),
ATI Radeon XPRESS 200 5A41 (PCIE),
ATI Radeon XPRESS 200M 5A42 (PCIE),
ATI Radeon XPRESS 200 5A61 (PCIE),
ATI Radeon XPRESS 200M 5A62 (PCIE),
ATI Radeon X300 (RV370) 5B60 (PCIE),
ATI Radeon X600 (RV370) 5B62 (PCIE),
ATI Radeon X550 (RV370) 5B63 (PCIE),
ATI FireGL V3100 (RV370) 5B64 (PCIE),
ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
ATI Mobility Radeon X800 XT (M28) (PCIE),
ATI Mobility FireGL V5100 (M28) (PCIE),
ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
ATI Radeon X850 XT PE (R480) (PCIE),
ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
ATI Radeon X850 XT (R480) (PCIE),
ATI Radeon X800XT (R423) 5D57 (PCIE),
ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
ATI Radeon X700 PRO (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
ATI Mobility Radeon X1700, ATI Radeon X2300HD,
ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
AMD FireStream 9250, ATI FirePro V8700 (FireGL),
ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
ATI Mobility RADEON HD 4870, ATI Radeon 4800 Series,
ATI Radeon 4800 Series, ATI FirePro M7750, ATI M98, ATI M98, ATI M98,
ATI Mobility Radeon HD 4650, ATI Radeon RV730 (AGP),
ATI Mobility Radeon HD 4670, ATI FirePro M5750,
ATI Mobility Radeon HD 4670, ATI Radeon RV730 (AGP),
ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
ATI Mobility Radeon HD 3850 X2, ATI RV670,
ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
ATI Radeon RV710, ATI Radeon RV710, ATI Radeon RV710,
ATI Radeon HD 4350, ATI Mobility Radeon 4300 Series,
ATI Mobility Radeon 4500 Series, ATI Mobility Radeon 4500 Series,
ATI FirePro RG220, ATI Mobility Radeon 4330, ATI RV630,
ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
ATI FireGL V3600, ATI Radeon HD 2600 LE,
ATI Mobility FireGL Graphics Processor, ATI Radeon HD 3470,
ATI Mobility Radeon HD 3430, ATI Mobility Radeon HD 3400 Series,
ATI Radeon HD 3450, ATI Radeon HD 3450, ATI Radeon HD 3430,
ATI Radeon HD 3450, ATI FirePro V3700, ATI FireMV 2450,
ATI FireMV 2260, ATI FireMV 2260, ATI Radeon HD 3600 Series,
ATI Radeon HD 3650 AGP, ATI Radeon HD 3600 PRO,
ATI Radeon HD 3600 XT, ATI Radeon HD 3600 PRO,
ATI Mobility Radeon HD 3650, ATI Mobility Radeon HD 3670,
ATI Mobility FireGL V5700, ATI Mobility FireGL V5725,
ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
ATI Radeon HD 3300 Graphics, ATI Radeon HD 3200 Graphics,
ATI Radeon 3000 Graphics, ATI Radeon HD 4200, ATI Radeon 4100,
ATI Mobility Radeon HD 4200, ATI Mobility Radeon 4100,
ATI Radeon HD 4290, ATI Radeon HD 4250, AMD Radeon HD 6310 Graphics,
AMD Radeon HD 6310 Graphics, AMD Radeon HD 6250 Graphics,
AMD Radeon HD 6250 Graphics, AMD Radeon HD 6300 Series Graphics,
AMD Radeon HD 6200 Series Graphics, CYPRESS,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, AMD Firestream 9370,
AMD Firestream 9350, ATI Radeon HD 5800 Series,
ATI Radeon HD 5800 Series, ATI Radeon HD 5800 Series,
ATI Radeon HD 5800 Series, ATI Radeon HD 5900 Series,
ATI Radeon HD 5900 Series, ATI Mobility Radeon HD 5800 Series,
ATI Mobility Radeon HD 5800 Series,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter,
ATI Mobility Radeon HD 5800 Series, ATI Radeon HD 5700 Series,
ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
ATI Mobility Radeon HD 5000 Series,
ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon HD 5570,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5670,
ATI Radeon HD 5570, ATI Radeon HD 5500 Series, REDWOOD,
ATI Mobility Radeon HD 5000 Series,
ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon Graphics,
ATI Mobility Radeon Graphics, CEDAR,
ATI FirePro (FireGL) Graphics Adapter,
ATI FirePro (FireGL) Graphics Adapter, ATI FirePro 2270, CEDAR,
ATI Radeon HD 5450, CEDAR, CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN,
CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN, AMD Radeon HD 6900 Series,
AMD Radeon HD 6900 Series, CAYMAN, CAYMAN, CAYMAN,
AMD Radeon HD 6900M Series, Mobility Radeon HD 6000 Series, BARTS,
BARTS, Mobility Radeon HD 6000 Series,
Mobility Radeon HD 6000 Series, BARTS, BARTS, BARTS, BARTS,
AMD Radeon HD 6800 Series, AMD Radeon HD 6800 Series,
AMD Radeon HD 6700 Series, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, CAICOS, CAICOS,
CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS,
CAICOS
[ 2985.272] (--) using VT number 8
[ 2985.277] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
[ 2985.277] (II) [KMS] Kernel modesetting enabled.
[ 2985.277] (II) RADEON(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 2985.277] (==) RADEON(0): Depth 24, (--) framebuffer bpp 32
[ 2985.277] (II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[ 2985.277] (==) RADEON(0): Default visual is TrueColor
[ 2985.277] (==) RADEON(0): RGB weight 888
[ 2985.277] (II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
[ 2985.277] (--) RADEON(0): Chipset: "AMD Radeon HD 6800 Series" (ChipID = 0x6738)
[ 2985.277] (II) RADEON(0): PCIE card detected
[ 2985.277] drmOpenDevice: node name is /dev/dri/card0
[ 2985.277] drmOpenDevice: open result is 8, (OK)
[ 2985.277] drmOpenByBusid: Searching for BusID pci:0000:03:00.0
[ 2985.277] drmOpenDevice: node name is /dev/dri/card0
[ 2985.277] drmOpenDevice: open result is 8, (OK)
[ 2985.277] drmOpenByBusid: drmOpenMinor returns 8
[ 2985.277] drmOpenByBusid: drmGetBusid reports pci:0000:03:00.0
[ 2985.277] (II) Loading sub module "exa"
[ 2985.277] (II) LoadModule: "exa"
[ 2985.277] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 2985.277] (II) Module exa: vendor="X.Org Foundation"
[ 2985.277] compiled for 1.10.3.901, module version = 2.5.0
[ 2985.277] ABI class: X.Org Video Driver, version 10.0
[ 2985.277] (II) RADEON(0): KMS Color Tiling: disabled
[ 2985.277] (II) RADEON(0): KMS Pageflipping: enabled
[ 2985.277] (II) RADEON(0): SwapBuffers wait for vsync: enabled
[ 2985.296] (II) RADEON(0): Output DisplayPort-0 has no monitor section
[ 2985.316] (II) RADEON(0): Output DisplayPort-1 has no monitor section
[ 2985.422] (II) RADEON(0): Output HDMI-0 using monitor section bar
[ 2985.422] (**) RADEON(0): Option "RightOf" "foo"
[ 2985.426] (II) RADEON(0): Output DVI-0 has no monitor section
[ 2985.532] (II) RADEON(0): Output DVI-1 using monitor section foo
[ 2985.543] (II) RADEON(0): EDID for output DisplayPort-0
[ 2985.556] (II) RADEON(0): EDID for output DisplayPort-1
[ 2985.662] (II) RADEON(0): EDID for output HDMI-0
[ 2985.662] (II) RADEON(0): Manufacturer: ACI Model: 27f6 Serial#: 77821
[ 2985.662] (II) RADEON(0): Year: 2010 Week: 34
[ 2985.662] (II) RADEON(0): EDID Version: 1.3
[ 2985.662] (II) RADEON(0): Digital Display Input
[ 2985.662] (II) RADEON(0): Max Image Size [cm]: horiz.: 60 vert.: 34
[ 2985.662] (II) RADEON(0): Gamma: 2.20
[ 2985.662] (II) RADEON(0): DPMS capabilities: Off
[ 2985.662] (II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2985.662] (II) RADEON(0): First detailed timing is preferred mode
[ 2985.662] (II) RADEON(0): redX: 0.647 redY: 0.334 greenX: 0.284 greenY: 0.607
[ 2985.662] (II) RADEON(0): blueX: 0.151 blueY: 0.071 whiteX: 0.313 whiteY: 0.329
[ 2985.662] (II) RADEON(0): Supported established timings:
[ 2985.662] (II) RADEON(0): 720x400@70Hz
[ 2985.662] (II) RADEON(0): 640x480@60Hz
[ 2985.662] (II) RADEON(0): 640x480@67Hz
[ 2985.662] (II) RADEON(0): 640x480@75Hz
[ 2985.662] (II) RADEON(0): 800x600@56Hz
[ 2985.662] (II) RADEON(0): 800x600@60Hz
[ 2985.662] (II) RADEON(0): 800x600@72Hz
[ 2985.662] (II) RADEON(0): 800x600@75Hz
[ 2985.662] (II) RADEON(0): 832x624@75Hz
[ 2985.662] (II) RADEON(0): 1024x768@60Hz
[ 2985.662] (II) RADEON(0): 1024x768@70Hz
[ 2985.662] (II) RADEON(0): 1024x768@75Hz
[ 2985.662] (II) RADEON(0): 1280x1024@75Hz
[ 2985.662] (II) RADEON(0): Manufacturer's mask: 0
[ 2985.662] (II) RADEON(0): Supported standard timings:
[ 2985.662] (II) RADEON(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 2985.662] (II) RADEON(0): #1: hsize: 1280 vsize 720 refresh: 60 vid: 49281
[ 2985.662] (II) RADEON(0): #2: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 2985.662] (II) RADEON(0): #3: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 2985.662] (II) RADEON(0): #4: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 2985.662] (II) RADEON(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 2985.662] (II) RADEON(0): #6: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 2985.662] (II) RADEON(0): Supported detailed timing:
[ 2985.662] (II) RADEON(0): clock: 148.5 MHz Image Size: 598 x 336 mm
[ 2985.662] (II) RADEON(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 2985.662] (II) RADEON(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2985.662] (II) RADEON(0): Serial No: A8LMTF077821
[ 2985.662] (II) RADEON(0): Ranges: V min: 50 V max: 85 Hz, H min: 24 H max: 92 kHz, PixClock max 175 MHz
[ 2985.662] (II) RADEON(0): Monitor name: ASUS VE278
[ 2985.662] (II) RADEON(0): Supported detailed timing:
[ 2985.662] (II) RADEON(0): clock: 27.0 MHz Image Size: 521 x 293 mm
[ 2985.662] (II) RADEON(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 2985.662] (II) RADEON(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 2985.662] (II) RADEON(0): Supported detailed timing:
[ 2985.662] (II) RADEON(0): clock: 74.2 MHz Image Size: 521 x 293 mm
[ 2985.663] (II) RADEON(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 2985.663] (II) RADEON(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2985.663] (II) RADEON(0): Supported detailed timing:
[ 2985.663] (II) RADEON(0): clock: 74.2 MHz Image Size: 521 x 293 mm
[ 2985.663] (II) RADEON(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 2985.663] (II) RADEON(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2985.663] (II) RADEON(0): Supported detailed timing:
[ 2985.663] (II) RADEON(0): clock: 27.0 MHz Image Size: 521 x 293 mm
[ 2985.663] (II) RADEON(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 2985.663] (II) RADEON(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 2985.663] (II) RADEON(0): Number of EDID sections to follow: 1
[ 2985.663] (II) RADEON(0): EDID (in hex):
[ 2985.663] (II) RADEON(0): 00ffffffffffff000469f627fd2f0100
[ 2985.663] (II) RADEON(0): 22140103803c22782aeed5a555489b26
[ 2985.663] (II) RADEON(0): 125054b7ef00714f81c0814081809500
[ 2985.663] (II) RADEON(0): b300d1c00101023a801871382d40582c
[ 2985.663] (II) RADEON(0): 450056502100001e000000ff0041384c
[ 2985.663] (II) RADEON(0): 4d54463037373832310a000000fd0032
[ 2985.663] (II) RADEON(0): 55185c11000a202020202020000000fc
[ 2985.663] (II) RADEON(0): 00415355532056453237380a2020019d
[ 2985.663] (II) RADEON(0): 020322714f0102031112130414050e0f
[ 2985.663] (II) RADEON(0): 1d1e1f10230907018301000065030c00
[ 2985.663] (II) RADEON(0): 10008c0ad08a20e02d10103e96000925
[ 2985.663] (II) RADEON(0): 21000018011d007251d01e206e285500
[ 2985.663] (II) RADEON(0): 09252100001e011d00bc52d01e20b828
[ 2985.663] (II) RADEON(0): 554009252100001e8c0ad09020403120
[ 2985.663] (II) RADEON(0): 0c405500092521000018000000000000
[ 2985.663] (II) RADEON(0): 00000000000000000000000000000073
[ 2985.663] (II) RADEON(0): Printing probed modes for output HDMI-0
[ 2985.663] (II) RADEON(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1280x720"x60.0 74.44 1280 1336 1472 1664 720 721 724 746 -hsync +vsync (44.7 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[ 2985.663] (II) RADEON(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 2985.663] (II) RADEON(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 2985.663] (II) RADEON(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
[ 2985.663] (II) RADEON(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 2985.663] (II) RADEON(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 2985.663] (II) RADEON(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 2985.663] (II) RADEON(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz)
[ 2985.663] (II) RADEON(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 2985.663] (II) RADEON(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
[ 2985.663] (II) RADEON(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 2985.663] (II) RADEON(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 2985.667] (II) RADEON(0): EDID for output DVI-0
[ 2985.773] (II) RADEON(0): EDID for output DVI-1
[ 2985.773] (II) RADEON(0): Manufacturer: ACI Model: 27f6 Serial#: 77822
[ 2985.773] (II) RADEON(0): Year: 2010 Week: 34
[ 2985.773] (II) RADEON(0): EDID Version: 1.3
[ 2985.773] (II) RADEON(0): Digital Display Input
[ 2985.773] (II) RADEON(0): Max Image Size [cm]: horiz.: 60 vert.: 34
[ 2985.773] (II) RADEON(0): Gamma: 2.20
[ 2985.773] (II) RADEON(0): DPMS capabilities: Off
[ 2985.773] (II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2985.773] (II) RADEON(0): First detailed timing is preferred mode
[ 2985.773] (II) RADEON(0): redX: 0.647 redY: 0.334 greenX: 0.284 greenY: 0.607
[ 2985.773] (II) RADEON(0): blueX: 0.151 blueY: 0.071 whiteX: 0.313 whiteY: 0.329
[ 2985.773] (II) RADEON(0): Supported established timings:
[ 2985.773] (II) RADEON(0): 720x400@70Hz
[ 2985.773] (II) RADEON(0): 640x480@60Hz
[ 2985.773] (II) RADEON(0): 640x480@67Hz
[ 2985.773] (II) RADEON(0): 640x480@75Hz
[ 2985.773] (II) RADEON(0): 800x600@56Hz
[ 2985.773] (II) RADEON(0): 800x600@60Hz
[ 2985.773] (II) RADEON(0): 800x600@72Hz
[ 2985.773] (II) RADEON(0): 800x600@75Hz
[ 2985.773] (II) RADEON(0): 832x624@75Hz
[ 2985.773] (II) RADEON(0): 1024x768@60Hz
[ 2985.773] (II) RADEON(0): 1024x768@70Hz
[ 2985.773] (II) RADEON(0): 1024x768@75Hz
[ 2985.773] (II) RADEON(0): 1280x1024@75Hz
[ 2985.773] (II) RADEON(0): Manufacturer's mask: 0
[ 2985.773] (II) RADEON(0): Supported standard timings:
[ 2985.773] (II) RADEON(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 2985.773] (II) RADEON(0): #1: hsize: 1280 vsize 720 refresh: 60 vid: 49281
[ 2985.773] (II) RADEON(0): #2: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 2985.773] (II) RADEON(0): #3: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 2985.773] (II) RADEON(0): #4: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 2985.773] (II) RADEON(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 2985.773] (II) RADEON(0): #6: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 2985.773] (II) RADEON(0): Supported detailed timing:
[ 2985.773] (II) RADEON(0): clock: 148.5 MHz Image Size: 598 x 336 mm
[ 2985.773] (II) RADEON(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 2985.773] (II) RADEON(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2985.773] (II) RADEON(0): Serial No: A8LMTF077822
[ 2985.773] (II) RADEON(0): Ranges: V min: 50 V max: 85 Hz, H min: 24 H max: 92 kHz, PixClock max 175 MHz
[ 2985.773] (II) RADEON(0): Monitor name: ASUS VE278
[ 2985.773] (II) RADEON(0): Supported detailed timing:
[ 2985.773] (II) RADEON(0): clock: 27.0 MHz Image Size: 521 x 293 mm
[ 2985.773] (II) RADEON(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 2985.773] (II) RADEON(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 2985.773] (II) RADEON(0): Supported detailed timing:
[ 2985.773] (II) RADEON(0): clock: 74.2 MHz Image Size: 521 x 293 mm
[ 2985.773] (II) RADEON(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 2985.773] (II) RADEON(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2985.773] (II) RADEON(0): Supported detailed timing:
[ 2985.773] (II) RADEON(0): clock: 74.2 MHz Image Size: 521 x 293 mm
[ 2985.773] (II) RADEON(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 2985.773] (II) RADEON(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2985.773] (II) RADEON(0): Supported detailed timing:
[ 2985.773] (II) RADEON(0): clock: 27.0 MHz Image Size: 521 x 293 mm
[ 2985.773] (II) RADEON(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 2985.773] (II) RADEON(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 2985.773] (II) RADEON(0): Number of EDID sections to follow: 1
[ 2985.773] (II) RADEON(0): EDID (in hex):
[ 2985.773] (II) RADEON(0): 00ffffffffffff000469f627fe2f0100
[ 2985.773] (II) RADEON(0): 22140103803c22782aeed5a555489b26
[ 2985.773] (II) RADEON(0): 125054b7ef00714f81c0814081809500
[ 2985.773] (II) RADEON(0): b300d1c00101023a801871382d40582c
[ 2985.773] (II) RADEON(0): 450056502100001e000000ff0041384c
[ 2985.773] (II) RADEON(0): 4d54463037373832320a000000fd0032
[ 2985.773] (II) RADEON(0): 55185c11000a202020202020000000fc
[ 2985.773] (II) RADEON(0): 00415355532056453237380a2020019b
[ 2985.773] (II) RADEON(0): 020322714f0102031112130414050e0f
[ 2985.773] (II) RADEON(0): 1d1e1f10230907018301000065030c00
[ 2985.773] (II) RADEON(0): 10008c0ad08a20e02d10103e96000925
[ 2985.773] (II) RADEON(0): 21000018011d007251d01e206e285500
[ 2985.773] (II) RADEON(0): 09252100001e011d00bc52d01e20b828
[ 2985.773] (II) RADEON(0): 554009252100001e8c0ad09020403120
[ 2985.773] (II) RADEON(0): 0c405500092521000018000000000000
[ 2985.773] (II) RADEON(0): 00000000000000000000000000000073
[ 2985.773] (II) RADEON(0): Printing probed modes for output DVI-1
[ 2985.773] (II) RADEON(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1280x720"x60.0 74.44 1280 1336 1472 1664 720 721 724 746 -hsync +vsync (44.7 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[ 2985.773] (II) RADEON(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 2985.773] (II) RADEON(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 2985.773] (II) RADEON(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
[ 2985.773] (II) RADEON(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 2985.773] (II) RADEON(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 2985.773] (II) RADEON(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 2985.774] (II) RADEON(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz)
[ 2985.774] (II) RADEON(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 2985.774] (II) RADEON(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
[ 2985.774] (II) RADEON(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 2985.774] (II) RADEON(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 2985.774] (II) RADEON(0): Output DisplayPort-0 disconnected
[ 2985.774] (II) RADEON(0): Output DisplayPort-1 disconnected
[ 2985.774] (II) RADEON(0): Output HDMI-0 connected
[ 2985.774] (II) RADEON(0): Output DVI-0 disconnected
[ 2985.774] (II) RADEON(0): Output DVI-1 connected
[ 2985.774] (II) RADEON(0): Using user preference for initial modes
[ 2985.774] (II) RADEON(0): Output HDMI-0 using initial mode 1920x1080
[ 2985.774] (II) RADEON(0): Output DVI-1 using initial mode 1920x1080
[ 2985.774] (II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 2985.774] (II) RADEON(0): mem size init: gart size :1fdff000 vram size: s:40000000 visible:f7d7000
[ 2985.774] (II) RADEON(0): EXA: Driver will allow EXA pixmaps in VRAM
[ 2985.774] (==) RADEON(0): DPI set to (96, 96)
[ 2985.774] (II) Loading sub module "fb"
[ 2985.774] (II) LoadModule: "fb"
[ 2985.774] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 2985.774] (II) Module fb: vendor="X.Org Foundation"
[ 2985.774] compiled for 1.10.3.901, module version = 1.0.0
[ 2985.774] ABI class: X.Org ANSI C Emulation, version 0.4
[ 2985.774] (II) Loading sub module "ramdac"
[ 2985.774] (II) LoadModule: "ramdac"
[ 2985.774] (II) Module "ramdac" already built-in
[ 2985.774] (--) Depth 24 pixmap format is 32 bpp
[ 2985.774] (II) RADEON(0): [DRI2] Setup complete
[ 2985.774] (II) RADEON(0): [DRI2] DRI driver: r600
[ 2985.774] (II) RADEON(0): Front buffer size: 16200K
[ 2985.774] (II) RADEON(0): VRAM usage limit set to 213829K
[ 2985.774] (==) RADEON(0): Backing store disabled
[ 2985.774] (II) RADEON(0): Direct rendering enabled
[ 2985.774] (II) RADEON(0): Setting EXA maxPitchBytes
[ 2985.774] (II) EXA(0): Driver allocated offscreen pixmaps
[ 2985.774] (II) EXA(0): Driver registered support for the following operations:
[ 2985.774] (II) Solid
[ 2985.774] (II) Copy
[ 2985.774] (II) Composite (RENDER acceleration)
[ 2985.774] (II) UploadToScreen
[ 2985.774] (II) DownloadFromScreen
[ 2985.774] (II) RADEON(0): Acceleration enabled
[ 2985.774] (==) RADEON(0): DPMS enabled
[ 2985.774] (==) RADEON(0): Silken mouse enabled
[ 2985.774] (II) RADEON(0): Set up textured video
[ 2985.774] (II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 2985.774] (--) RandR disabled
[ 2985.774] (II) Initializing built-in extension Generic Event Extension
[ 2985.774] (II) Initializing built-in extension SHAPE
[ 2985.774] (II) Initializing built-in extension MIT-SHM
[ 2985.774] (II) Initializing built-in extension XInputExtension
[ 2985.774] (II) Initializing built-in extension XTEST
[ 2985.774] (II) Initializing built-in extension BIG-REQUESTS
[ 2985.774] (II) Initializing built-in extension SYNC
[ 2985.774] (II) Initializing built-in extension XKEYBOARD
[ 2985.774] (II) Initializing built-in extension XC-MISC
[ 2985.774] (II) Initializing built-in extension SECURITY
[ 2985.774] (II) Initializing built-in extension XINERAMA
[ 2985.774] (II) Initializing built-in extension XFIXES
[ 2985.774] (II) Initializing built-in extension RENDER
[ 2985.774] (II) Initializing built-in extension RANDR
[ 2985.774] (II) Initializing built-in extension COMPOSITE
[ 2985.774] (II) Initializing built-in extension DAMAGE
[ 2985.780] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 2985.780] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 2985.780] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 2985.780] (II) AIGLX: enabled GLX_SGI_make_current_read
[ 2985.780] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 2985.780] (II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/r600_dri.so
[ 2985.780] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 2985.781] (II) RADEON(0): Setting screen physical size to 1016 x 285
[ 2985.813] (II) config/udev: Adding input device Power Button (/dev/input/event6)
[ 2985.813] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2985.813] (II) LoadModule: "evdev"
[ 2985.813] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2985.813] (II) Module evdev: vendor="X.Org Foundation"
[ 2985.813] compiled for 1.10.0, module version = 2.6.0
[ 2985.813] Module class: X.Org XInput Driver
[ 2985.813] ABI class: X.Org XInput driver, version 12.2
[ 2985.813] (II) Using input driver 'evdev' for 'Power Button'
[ 2985.813] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2985.813] (**) Power Button: always reports core events
[ 2985.813] (**) Power Button: Device: "/dev/input/event6"
[ 2985.813] (--) Power Button: Found keys
[ 2985.813] (II) Power Button: Configuring as keyboard
[ 2985.813] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input6/event6"
[ 2985.813] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 2985.813] (**) Option "xkb_rules" "evdev"
[ 2985.813] (**) Option "xkb_model" "evdev"
[ 2985.813] (**) Option "xkb_layout" "us"
[ 2985.832] (II) config/udev: Adding input device Power Button (/dev/input/event5)
[ 2985.832] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2985.832] (II) Using input driver 'evdev' for 'Power Button'
[ 2985.832] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2985.832] (**) Power Button: always reports core events
[ 2985.832] (**) Power Button: Device: "/dev/input/event5"
[ 2985.832] (--) Power Button: Found keys
[ 2985.832] (II) Power Button: Configuring as keyboard
[ 2985.832] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5/event5"
[ 2985.832] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 2985.832] (**) Option "xkb_rules" "evdev"
[ 2985.832] (**) Option "xkb_model" "evdev"
[ 2985.832] (**) Option "xkb_layout" "us"
[ 2985.835] (II) config/udev: Adding input device HD-Audio Generic HDMI/DP (/dev/input/event9)
[ 2985.835] (II) No input driver/identifier specified (ignoring)
[ 2985.836] (II) config/udev: Adding input device Logitech Logitech Illuminated Keyboard (/dev/input/event0)
[ 2985.836] (**) Logitech Logitech Illuminated Keyboard: Applying InputClass "evdev keyboard catchall"
[ 2985.836] (II) Using input driver 'evdev' for 'Logitech Logitech Illuminated Keyboard'
[ 2985.836] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2985.836] (**) Logitech Logitech Illuminated Keyboard: always reports core events
[ 2985.836] (**) Logitech Logitech Illuminated Keyboard: Device: "/dev/input/event0"
[ 2985.836] (--) Logitech Logitech Illuminated Keyboard: Found keys
[ 2985.836] (II) Logitech Logitech Illuminated Keyboard: Configuring as keyboard
[ 2985.836] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.1/usb6/6-1/6-1:1.0/input/input0/event0"
[ 2985.836] (II) XINPUT: Adding extended input device "Logitech Logitech Illuminated Keyboard" (type: KEYBOARD)
[ 2985.836] (**) Option "xkb_rules" "evdev"
[ 2985.836] (**) Option "xkb_model" "evdev"
[ 2985.836] (**) Option "xkb_layout" "us"
[ 2985.837] (II) config/udev: Adding input device Logitech Logitech Illuminated Keyboard (/dev/input/event1)
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: Applying InputClass "evdev keyboard catchall"
[ 2985.837] (II) Using input driver 'evdev' for 'Logitech Logitech Illuminated Keyboard'
[ 2985.837] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: always reports core events
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: Device: "/dev/input/event1"
[ 2985.837] (--) Logitech Logitech Illuminated Keyboard: Found 1 mouse buttons
[ 2985.837] (--) Logitech Logitech Illuminated Keyboard: Found scroll wheel(s)
[ 2985.837] (--) Logitech Logitech Illuminated Keyboard: Found relative axes
[ 2985.837] (--) Logitech Logitech Illuminated Keyboard: Found absolute axes
[ 2985.837] (--) Logitech Logitech Illuminated Keyboard: Found keys
[ 2985.837] (II) Logitech Logitech Illuminated Keyboard: Configuring as mouse
[ 2985.837] (II) Logitech Logitech Illuminated Keyboard: Configuring as keyboard
[ 2985.837] (II) Logitech Logitech Illuminated Keyboard: Adding scrollwheel support
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: YAxisMapping: buttons 4 and 5
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2985.837] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.1/usb6/6-1/6-1:1.1/input/input1/event1"
[ 2985.837] (II) XINPUT: Adding extended input device "Logitech Logitech Illuminated Keyboard" (type: KEYBOARD)
[ 2985.837] (**) Option "xkb_rules" "evdev"
[ 2985.837] (**) Option "xkb_model" "evdev"
[ 2985.837] (**) Option "xkb_layout" "us"
[ 2985.837] (EE) Logitech Logitech Illuminated Keyboard: failed to initialize for relative axes.
[ 2985.837] (II) Logitech Logitech Illuminated Keyboard: initialized for absolute axes.
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: (accel) keeping acceleration scheme 1
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: (accel) acceleration profile 0
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: (accel) acceleration factor: 2.000
[ 2985.837] (**) Logitech Logitech Illuminated Keyboard: (accel) acceleration threshold: 4
[ 2985.837] (II) config/udev: Adding input device Logitech G500 (/dev/input/event2)
[ 2985.837] (**) Logitech G500: Applying InputClass "evdev pointer catchall"
[ 2985.837] (II) Using input driver 'evdev' for 'Logitech G500'
[ 2985.837] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2985.837] (**) Logitech G500: always reports core events
[ 2985.837] (**) Logitech G500: Device: "/dev/input/event2"
[ 2985.837] (--) Logitech G500: Found 20 mouse buttons
[ 2985.837] (--) Logitech G500: Found scroll wheel(s)
[ 2985.837] (--) Logitech G500: Found relative axes
[ 2985.837] (--) Logitech G500: Found x and y relative axes
[ 2985.837] (II) Logitech G500: Configuring as mouse
[ 2985.837] (II) Logitech G500: Adding scrollwheel support
[ 2985.837] (**) Logitech G500: YAxisMapping: buttons 4 and 5
[ 2985.837] (**) Logitech G500: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2985.837] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.1/usb6/6-2/6-2:1.0/input/input2/event2"
[ 2985.837] (II) XINPUT: Adding extended input device "Logitech G500" (type: MOUSE)
[ 2985.838] (II) Logitech G500: initialized for relative axes.
[ 2985.838] (**) Logitech G500: (accel) keeping acceleration scheme 1
[ 2985.838] (**) Logitech G500: (accel) acceleration profile 0
[ 2985.838] (**) Logitech G500: (accel) acceleration factor: 2.000
[ 2985.838] (**) Logitech G500: (accel) acceleration threshold: 4
[ 2985.838] (II) config/udev: Adding input device Logitech G500 (/dev/input/mouse0)
[ 2985.838] (II) No input driver/identifier specified (ignoring)
[ 2985.838] (II) config/udev: Adding input device Logitech G500 (/dev/input/event3)
[ 2985.838] (**) Logitech G500: Applying InputClass "evdev keyboard catchall"
[ 2985.838] (II) Using input driver 'evdev' for 'Logitech G500'
[ 2985.838] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2985.838] (**) Logitech G500: always reports core events
[ 2985.838] (**) Logitech G500: Device: "/dev/input/event3"
[ 2985.838] (--) Logitech G500: Found 1 mouse buttons
[ 2985.838] (--) Logitech G500: Found scroll wheel(s)
[ 2985.838] (--) Logitech G500: Found relative axes
[ 2985.838] (--) Logitech G500: Found absolute axes
[ 2985.838] (--) Logitech G500: Found keys
[ 2985.838] (II) Logitech G500: Configuring as mouse
[ 2985.838] (II) Logitech G500: Configuring as keyboard
[ 2985.838] (II) Logitech G500: Adding scrollwheel support
[ 2985.838] (**) Logitech G500: YAxisMapping: buttons 4 and 5
[ 2985.838] (**) Logitech G500: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2985.838] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.1/usb6/6-2/6-2:1.1/input/input3/event3"
[ 2985.838] (II) XINPUT: Adding extended input device "Logitech G500" (type: KEYBOARD)
[ 2985.838] (**) Option "xkb_rules" "evdev"
[ 2985.838] (**) Option "xkb_model" "evdev"
[ 2985.838] (**) Option "xkb_layout" "us"
[ 2985.838] (EE) Logitech G500: failed to initialize for relative axes.
[ 2985.838] (II) Logitech G500: initialized for absolute axes.
[ 2985.838] (**) Logitech G500: (accel) keeping acceleration scheme 1
[ 2985.838] (**) Logitech G500: (accel) acceleration profile 0
[ 2985.838] (**) Logitech G500: (accel) acceleration factor: 2.000
[ 2985.838] (**) Logitech G500: (accel) acceleration threshold: 4
[ 2985.840] (II) config/udev: Adding input device HDA Intel Headphone (/dev/input/event8)
[ 2985.840] (II) No input driver/identifier specified (ignoring)
[ 2985.842] (II) config/udev: Adding input device Logitech Logitech G35 Headset (/dev/input/event4)
[ 2985.842] (**) Logitech Logitech G35 Headset: Applying InputClass "evdev keyboard catchall"
[ 2985.842] (II) Using input driver 'evdev' for 'Logitech Logitech G35 Headset'
[ 2985.842] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2985.842] (**) Logitech Logitech G35 Headset: always reports core events
[ 2985.842] (**) Logitech Logitech G35 Headset: Device: "/dev/input/event4"
[ 2985.842] (--) Logitech Logitech G35 Headset: Found 2 mouse buttons
[ 2985.842] (--) Logitech Logitech G35 Headset: Found absolute axes
[ 2985.842] (--) Logitech Logitech G35 Headset: Found keys
[ 2985.842] (II) Logitech Logitech G35 Headset: Configuring as mouse
[ 2985.842] (II) Logitech Logitech G35 Headset: Configuring as keyboard
[ 2985.842] (**) Logitech Logitech G35 Headset: YAxisMapping: buttons 4 and 5
[ 2985.842] (**) Logitech Logitech G35 Headset: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2985.842] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb9/9-1/9-1:1.3/input/input4/event4"
[ 2985.842] (II) XINPUT: Adding extended input device "Logitech Logitech G35 Headset" (type: KEYBOARD)
[ 2985.842] (**) Option "xkb_rules" "evdev"
[ 2985.842] (**) Option "xkb_model" "evdev"
[ 2985.842] (**) Option "xkb_layout" "us"
[ 2985.842] (II) Logitech Logitech G35 Headset: initialized for absolute axes.
[ 2985.842] (**) Logitech Logitech G35 Headset: (accel) keeping acceleration scheme 1
[ 2985.842] (**) Logitech Logitech G35 Headset: (accel) acceleration profile 0
[ 2985.842] (**) Logitech Logitech G35 Headset: (accel) acceleration factor: 2.000
[ 2985.842] (**) Logitech Logitech G35 Headset: (accel) acceleration threshold: 4
[ 2985.845] (II) config/udev: Adding input device PC Speaker (/dev/input/event7)
[ 2985.845] (II) No input driver/identifier specified (ignoring)
[ 2986.246] (II) RADEON(0): EDID vendor "ACI", prod id 10230
[ 2986.246] (II) RADEON(0): Using EDID range info for horizontal sync
[ 2986.246] (II) RADEON(0): Using EDID range info for vertical refresh
[ 2986.246] (II) RADEON(0): Printing DDC gathered Modelines:
[ 2986.246] (II) RADEON(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "720x480"x0.0 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1280x720"x0.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "720x576"x0.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz)
[ 2986.246] (II) RADEON(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 2986.246] (II) RADEON(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 2986.246] (II) RADEON(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
[ 2986.246] (II) RADEON(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 2986.246] (II) RADEON(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 2986.246] (II) RADEON(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 2986.246] (II) RADEON(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1280x720"x60.0 74.48 1280 1336 1472 1664 720 721 724 746 -hsync +vsync (44.8 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1920x1080i"x0.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1920x1080i"x0.0 74.25 1920 2008 2052 2200 1080 1084 1094 1125 interlace +hsync +vsync (33.8 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1440x576i"x0.0 27.00 1440 1464 1590 1728 576 580 586 625 interlace -hsync -vsync (15.6 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1440x480i"x0.0 27.00 1440 1478 1602 1716 480 488 494 525 interlace -hsync -vsync (15.7 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1440x480"x0.0 54.00 1440 1472 1596 1716 480 489 495 525 -hsync -vsync (31.5 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1440x576"x0.0 54.00 1440 1464 1592 1728 576 581 586 625 -hsync -vsync (31.2 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1920x1080"x0.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2986.246] (II) RADEON(0): Modeline "1920x1080"x0.0 74.25 1920 2558 2602 2750 1080 1084 1089 1125 +hsync +vsync (27.0 kHz)
[ 2986.250] (II) RADEON(0): Allocate new frame buffer 1920x1080 stride 1920
[ 2986.250] (II) RADEON(0): VRAM usage limit set to 221119K -
How do I get my Macbook Pro 15" to run dual monitor setup with Dual Link DVI outputs
I own have two 27" 2560x1440 WQHD LED IPS Computer monitors and have been trying to get them to work with my macbook pro 15" w retina for over a month now. I have purchased multiple products and nothing has worked. The big problem is that the only input that the monitors have is a Dual Link DVI input. The closest that i have gotten to getting them to work was this morning when I bought 2 Mini Display Port to Dual Link DVI Adapters for $99 a peice. Below is a link
http://store.apple.com/us/product/MB571Z/A/mini-displayport-to-dual-link-dvi-ada pter?afid=p219%7CGOUS&cid=AOS-US-KWG-PLA
Problem is that when I hook them up, I still only get a picture on one of the screens. Also, it requires you to plug into a mini Display port and USB port which takes up all of the space for me to run any othe peripherals. Though it has a built in USB port, when I plug my apple keybaord into it, I get an saying "USB Device Needs power, connect "keyboard Hub" to power or usb port on this mac"
I have looked everywhere for a docking station that would satisfy my needs, however, it does not exist. I use my macbook as my main office computer and take it home with me every night. I switched from the lenovo thinkpad to the macbook and have been satsified with my decision except for the fact that i cannot connect my monitors to it.
Please help!Yes, that would work, however it would cost me $2000 for the monitors.
-
Can't get dual monitors to come back up when docking. T500 with mini dock & XP
I have a T500 with XP installed. I am using it docked into a mini dock attached to two 20inch Viewsonic monitors. One connected via VGA and the other DVI. I setup the dual monitors just fine. Anytime after I undock and boot up the laptop I can't get the dual monitors to automatically display. I have to go into the display properties and re set it up each time. Can anyone suggest any ideas?
When your T500 power-on , press F1 to log in BIOS, and change the option in >config>Display>Boot-Display-Device to Both or VGA, I suppose that it will reslove your problem.
-
Photoshop CS6 constant 25% CPU Usage with Nvidia card (nvoglv64.dll)
Hi,
i'm using Adobe Photoshop CS6 (Cloud) and have the latest version installed. I experience a high cpu problem when i want to zoom in the picture, then sometimes the cpu load of the CS6 process is constant on 25%. I tried the graphic advanced settings in CS6 from light, normal, extended. With the light setting it happens not so often, but sometimes it is there.
My driver version is 310.90, but this happened also with previous versions or with beta 313.96.
My graphic card is a Gigabyte GeForce GTX 470 Super Overclock with two different monitors connected.
Does anyone else have this problem?
I want to buy a newer Nvidia card in the near future, but it would be not so good if the problems persists.
Here you can see a screenshot from the Process-Explorer.
I can work more or less with CS6, that is not the problem, but the constant cpu load bothers me.
Maybe someone have some ideas to solve this?
Thanks!
ByePhotoshop demands a lot of the system, but it doesn't normally run in a loop like that. It sounds like you have a specific nVidia driver problem.
Does everything else work right?
You might see if nVidia offers any advice on their support site for how to clean old driver remnants out of your system that might have accumulated, then install the latest driver again.
Have you tried changing the various settings in Edit - Preferences - Performance, in the [Advanced] section? Your card should be capable of Advanced operation, but maybe as a workaround you could try Basic mode (making sure to close and restart Photoshop before testing). If nothing else it could help isolate the issue further. Since in Normal and Advanced modes the monitor color management is done in the GPU (and in the CPU in Basic mode), it might be interesting to see whether switching to Basic helps. If it does, you should review what color profiles you have set up for your monitors. Profiles are complex beasts and they can be screwed up in a variety of ways and cause pretty weird things to happen.
Good luck.
-Noel -
[Solved]Openbox dual monitor crashing
I have been working this out for days to no avail. I have an ATI video card not using the catalyst drivers. Dual monitors worked fine in KDE without any additional setup, and no xorg.conf. In openbox i have tried with arandr, and manual. but when i enable the second monitor its seems that openbox crashes, because whatever is on the screen at the time of enabling the monitor turns to static. I think its openbox because i still have a functional mouse cursor and has proper fucntions accross both monitors in any configuration that i try. when it crashes i have to hard reboot. when i reboot with the monitor still plugged in, both lvds and vga will display a cloned image at the same resolution which is the wrong resolution for both lvds and vga.
I have googled till there is no link unclicked, and wiki give me nothing. i dont believe that i need to set up an xorg.conf as the external is detected fine. its almost like when x applies the settings it corrupts openbox.
anyone have any ideas?
Last edited by zero_one (2010-09-18 18:26:28)zero_one wrote:you mean add the monitors to a xx-monitor.conf? i can give that a try but it doesnt seem that would provide the flexibility that im looking for as sometimes i use the external monitor disabiling lvds, sometimes right of, and sometimes i use hdmi to my tv set right of, to watch movies.
I mean add the monitors to xorg.conf. Here is the xorg.conf I use with openbox (separate X display for the TV), just to give you an idea - yours will differ with ATI:
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen[0]"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "ServerLayout"
Identifier "tv"
Screen 0 "Screen[1]" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Module"
Load "glx"
EndSection
Section "Files"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
Option "AutoRepeat" "210 50" #added, did no good, use ~/.xinitrc xset
Option "XkbOptions" "terminate:ctrl_alt_bksp"
EndSection
Section "Monitor"
Identifier "Monitor[0]"
HorizSync 31.0 - 83.0
VertRefresh 55.0 - 76.0
Option "DPMS"
EndSection
Section "Monitor"
Identifier "Monitor[1]"
HorizSync 15.0 - 620.0
VertRefresh 15.0 - 600.0
EndSection
Section "Device"
Identifier "Device[0]"
Driver "nvidia"
BoardName "GeForce 8500 GT"
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "Device[1]"
Driver "nvidia"
BoardName "GeForce 8500 GT"
#adjust using 'lspci' or cat /proc/pci
BusID "PCI:1:0:0"
Option "ConnectedMonitor" "TV"
EndSection
Section "Screen"
#nvidia
Identifier "Screen[0]"
Device "Device[0]"
Monitor "Monitor[0]"
DefaultDepth 24
Option "TwinView" "0"
# Option "metamodes" "DFP: nvidia-auto-select +0+0"
Option "NoLogo" "True"
Option "RenderAccel" "True"
Option "AddARGBGLXVisuals" "True"
SubSection "Display"
Depth 24
Modes "nvidia-auto-select"
EndSubSection
EndSection
Section "Screen"
#nvidia
Identifier "Screen[1]"
Device "Device[1]"
Monitor "Monitor[1]"
DefaultDepth 24
Option "TwinView" "0"
Option "UseEDID" "FALSE"
Option "ConnectedMonitor" "TV"
Option "TvOutFormat" "Component"
Option "metamodes" "CRT: 1920x1080 +0+0"
Option "TVStandard" "HD1080i"
Option "RenderAccel" "True"
Option "AddARGBGLXVisuals" "True"
SubSection "Display"
Depth 24
Modes "nvidia-auto-select"
EndSubSection
EndSection
Then I start the second X display on the TV with this in openbox's autostart.sh:
(sleep 5 && xinit /usr/bin/openbox -- /usr/bin/X :1 -layout tv -nolisten tcp) &
Thus there are two instances of openbox running.
It may not give you the flexibility, but for testing it may help you narrow down what is causing the problem and find remedies.
Also, the monitor turning to static sounds more like a driver or X issue than something with openbox.
Last edited by IgnorantGuru (2010-09-18 17:46:12) -
[solved] XFCE Dual monitor causes theme & icon, xconf issues
Hey all,
Here is the issue:
I have sony svz13114gxx laptop with xfce4 DE, i just tried to hook up external vga monitor to laptop and everything configures right (no mirroring) with this run in normal session:
xrandr --output eDP1 --mode 1920x1080
xrandr --newmode "1920x1200_60.00" 193.25 1920 2056 2256 2592 1200 1203 1209 1245 -hsync +vsync
xrandr --addmode VGA1 1920x1200_60.00
xrandr --output VGA1 --mode 1920x1200_60.00
xrandr --output VGA1 --left-of eDP1
Obviously when i reboot this is not persistent, so then i put this stuff in my /etc/X11/xorg.conf.d/20-intel.conf:
Section "Device"
Identifier "Intel Graphics"
Driver "intel"
Option "AccelMethod" "sna"
Option "monitor-eDP1" "eDP1"
Option "monitor-VGA1" "VGA1"
EndSection
Section "Monitor"
Identifier "VGA1"
Modeline "1920x1200_60.00" 193.25 1920 2056 2256 2592 1200 1203 1209 1245 -HSync +VSync
Option "PreferredMode" "1920x1200_60.00"
EndSection
Section "Monitor"
Identifier "eDP1"
Option "PreferredMode" "1920x1080"
Option "Primary" "true"
Option "Position" "1920 0"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Intel Graphics"
Monitor "eDP1"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
This is where the problems start. On reboot Slim desktop manager seems to be stretched properly across the two monitors, but the I login and the display switches back to being mirrored, my xfce gtk2 theme is disabled in favor of somee default looking one, my icons are back to default, and none of my custom keyboard shorcuts work.
I can then use xrandr to get the displays in extended mode again, but the themes and icons etc do not revert. And on reboot, i have the same issue.
I have tried the sourcing ~/.xprofile, ~/.xinitrc, and ~/.config.xfce4/xinitrc routes, putting the xrandr cammands above the exec lines and that doesn't even enable VGA1.
I have been to all these places
https://wiki.ubuntu.com/X/Config/Resolution#Xrandr_Graphical_Front_End_GUI
http://ilkinbalkanay.blogspot.com/2008/01/extended-desktop-configuration-with.html
https://bbs.archlinux.org/viewtopic.php?id=98747
https://www.google.com/search?q=arch%20xrandr&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a&source=hp&channel=np
https://wiki.archlinux.org/index.php/Execute_commands_after_X_start
http://intellinuxgraphics.org/dualhead.html
http://mac.linux.be/content/setting-xorgconf-manually-xrandr#3
https://www.google.com/search?q=arch%20dual%20monitors%20The%20last%20active%20output%20must%20not%20be%20disabled%2C%20the%20system%20would%20be%20unusable.&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a&source=hp&channel=np#hl=en&safe=off&client=firefox-a&tbo=d&rls=org.mozilla:en-US%3Aofficial&channel=np&sclient=psy-ab&q=xfce+%22Selected+output+not+disabled%22&oq=xfce+%22Selected+output+not+disabled%22&gs_l=serp.3...1694.1694.3.2205.1.1.0.0.0.0.97.97.1.1.0.les%3Bcrnk_timediscounta..0.0...1c.1.O4EDj7DaWlA&pbx=1&fp=1&bpcl=39468505&biw=984&bih=936&cad=b&sei=aKC_UIKvJ6GA0AGTg4HwBg&sei=FKS_UMuwJdPU0gHorICQBA&bav=on.2,or.r_gc.r_pw.r_qf.&sei=2MK_UOaAJ5Ph0wGbsoHICg
https://wiki.archlinux.org/index.php/Xfce#Customizing_Startup_Applications
http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/x-config.html
https://wiki.archlinux.org/index.php/Xorg#Monitor_settings
Even after much research, still no luck.
this might be useful:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=631225
Anyone have any ideas?
here is my Xorg0.log
[ 3.490]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 3.490] X Protocol Version 11, Revision 0
[ 3.490] Build Operating System: Linux 3.6.3-1-ARCH x86_64
[ 3.490] Current Operating System: Linux tcz 3.6.8-1-ARCH #1 SMP PREEMPT Mon Nov 26 22:10:40 CET 2012 x86_64
[ 3.490] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=d23251af-35fa-426b-a7d5-5aa2f0a5b87d ro quiet pcie_aspm=force i915.i915_enable_rc6=1
[ 3.490] Build Date: 08 November 2012 07:09:29PM
[ 3.490]
[ 3.490] Current version of pixman: 0.28.0
[ 3.490] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 3.490] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 3.490] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Dec 5 16:25:21 2012
[ 3.492] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 3.494] (==) No Layout section. Using the first Screen section.
[ 3.494] (**) |-->Screen "Default Screen" (0)
[ 3.494] (**) | |-->Monitor "eDP1"
[ 3.494] (**) | |-->Device "Intel Graphics"
[ 3.494] (==) Automatically adding devices
[ 3.494] (==) Automatically enabling devices
[ 3.494] (==) Automatically adding GPU devices
[ 3.504] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 3.504] Entry deleted from font path.
[ 3.504] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 3.504] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 3.504] Entry deleted from font path.
[ 3.504] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 3.504] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Type1/
[ 3.504] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 3.504] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 3.504] (II) Loader magic: 0x7fcc40
[ 3.504] (II) Module ABI versions:
[ 3.504] X.Org ANSI C Emulation: 0.4
[ 3.504] X.Org Video Driver: 13.1
[ 3.504] X.Org XInput driver : 18.0
[ 3.504] X.Org Server Extension : 7.0
[ 3.505] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 6.276] (--) PCI:*(0:0:2:0) 8086:0166:104d:90a5 rev 9, Mem @ 0xd7000000/4194304, 0xc0000000/268435456, I/O @ 0x00009000/64
[ 6.276] (II) Open ACPI successful (/var/run/acpid.socket)
[ 6.276] Initializing built-in extension Generic Event Extension
[ 6.276] Initializing built-in extension SHAPE
[ 6.276] Initializing built-in extension MIT-SHM
[ 6.276] Initializing built-in extension XInputExtension
[ 6.276] Initializing built-in extension XTEST
[ 6.276] Initializing built-in extension BIG-REQUESTS
[ 6.276] Initializing built-in extension SYNC
[ 6.276] Initializing built-in extension XKEYBOARD
[ 6.276] Initializing built-in extension XC-MISC
[ 6.276] Initializing built-in extension SECURITY
[ 6.276] Initializing built-in extension XINERAMA
[ 6.276] Initializing built-in extension XFIXES
[ 6.276] Initializing built-in extension RENDER
[ 6.276] Initializing built-in extension RANDR
[ 6.276] Initializing built-in extension COMPOSITE
[ 6.276] Initializing built-in extension DAMAGE
[ 6.276] Initializing built-in extension MIT-SCREEN-SAVER
[ 6.276] Initializing built-in extension DOUBLE-BUFFER
[ 6.276] Initializing built-in extension RECORD
[ 6.276] Initializing built-in extension DPMS
[ 6.276] Initializing built-in extension X-Resource
[ 6.276] Initializing built-in extension XVideo
[ 6.276] Initializing built-in extension XVideo-MotionCompensation
[ 6.276] Initializing built-in extension XFree86-VidModeExtension
[ 6.276] Initializing built-in extension XFree86-DGA
[ 6.276] Initializing built-in extension XFree86-DRI
[ 6.276] Initializing built-in extension DRI2
[ 6.276] (II) LoadModule: "glx"
[ 6.278] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 6.281] (II) Module glx: vendor="X.Org Foundation"
[ 6.281] compiled for 1.13.0, module version = 1.0.0
[ 6.281] ABI class: X.Org Server Extension, version 7.0
[ 6.281] (==) AIGLX enabled
[ 6.281] Loading extension GLX
[ 6.281] (II) LoadModule: "intel"
[ 6.281] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 6.285] (II) Module intel: vendor="X.Org Foundation"
[ 6.285] compiled for 1.13.0.901, module version = 2.20.14
[ 6.285] Module class: X.Org Video Driver
[ 6.285] ABI class: X.Org Video Driver, version 13.1
[ 6.285] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2),
Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2),
Haswell Server (GT2+), Haswell SDV Desktop (GT1),
Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+),
Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),
Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1),
Haswell SDV Server (GT2), Haswell SDV Server (GT2+),
Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),
Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1),
Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+),
Haswell ULT Server (GT1), Haswell ULT Server (GT2),
Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1),
Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+),
Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2),
Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1),
Haswell CRW Server (GT2), Haswell CRW Server (GT2+),
ValleyView PO board
[ 6.286] (++) using VT number 7
[ 6.288] (II) intel(0): using device path '/dev/dri/card0'
[ 6.288] (**) intel(0): Depth 24, (--) framebuffer bpp 32
[ 6.288] (==) intel(0): RGB weight 888
[ 6.288] (==) intel(0): Default visual is TrueColor
[ 6.288] (**) intel(0): Option "AccelMethod" "sna"
[ 6.288] (--) intel(0): Integrated Graphics Chipset: Intel(R) Ivybridge Mobile (GT2)
[ 6.289] (**) intel(0): Framebuffer tiled
[ 6.289] (**) intel(0): Pixmaps tiled
[ 6.289] (**) intel(0): 3D buffers tiled
[ 6.289] (**) intel(0): Throttling enabled
[ 6.289] (**) intel(0): Delayed flush enabled
[ 6.289] (**) intel(0): "Tear free" disabled
[ 6.289] (**) intel(0): Forcing per-crtc-pixmaps? no
[ 6.289] (II) intel(0): Output eDP1 using monitor section eDP1
[ 6.289] (**) intel(0): Option "PreferredMode" "1920x1080"
[ 6.289] (**) intel(0): Option "Position" "1920 0"
[ 6.289] (**) intel(0): Option "Primary" "true"
[ 6.289] (--) intel(0): found backlight control interface acpi_video0 (type 'firmware')
[ 6.293] (II) intel(0): Output VGA1 using monitor section VGA1
[ 6.293] (**) intel(0): Option "PreferredMode" "1920x1200_60.00"
[ 6.294] (II) intel(0): Output HDMI1 has no monitor section
[ 6.336] (II) intel(0): Output DP1 has no monitor section
[ 6.337] (II) intel(0): EDID for output eDP1
[ 6.337] (II) intel(0): Manufacturer: MS_ Model: 25 Serial#: 16843009
[ 6.337] (II) intel(0): Year: 2012 Week: 24
[ 6.337] (II) intel(0): EDID Version: 1.4
[ 6.337] (II) intel(0): Digital Display Input
[ 6.337] (II) intel(0): 8 bits per channel
[ 6.337] (II) intel(0): Digital interface is DisplayPort
[ 6.337] (II) intel(0): Max Image Size [cm]: horiz.: 29 vert.: 16
[ 6.337] (II) intel(0): Gamma: 2.20
[ 6.337] (II) intel(0): No DPMS capabilities specified
[ 6.337] (II) intel(0): Supported color encodings: RGB 4:4:4
[ 6.337] (II) intel(0): First detailed timing is preferred mode
[ 6.337] (II) intel(0): Preferred mode is native pixel format and refresh rate
[ 6.337] (II) intel(0): redX: 0.602 redY: 0.336 greenX: 0.296 greenY: 0.546
[ 6.337] (II) intel(0): blueX: 0.148 blueY: 0.126 whiteX: 0.313 whiteY: 0.329
[ 6.337] (II) intel(0): Manufacturer's mask: 0
[ 6.337] (II) intel(0): Supported standard timings:
[ 6.337] (II) intel(0): #0: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 6.337] (II) intel(0): Supported detailed timing:
[ 6.337] (II) intel(0): clock: 162.8 MHz Image Size: 291 x 164 mm
[ 6.337] (II) intel(0): h_active: 1920 h_sync: 1952 h_sync_end 1984 h_blank_end 2481 h_border: 0
[ 6.337] (II) intel(0): v_active: 1080 v_sync: 1083 v_sync_end 1086 v_blanking: 1095 v_border: 0
[ 6.337] (II) intel(0): Supported detailed timing:
[ 6.337] (II) intel(0): clock: 99.9 MHz Image Size: 291 x 164 mm
[ 6.337] (II) intel(0): h_active: 1920 h_sync: 1952 h_sync_end 1984 h_blank_end 2281 h_border: 0
[ 6.337] (II) intel(0): v_active: 1080 v_sync: 1083 v_sync_end 1086 v_blanking: 1095 v_border: 0
[ 6.337] (II) intel(0): Monitor name: Sony LCD
[ 6.337] (II) intel(0): Ranges: V min: 39 V max: 61 Hz, H min: 43 H max: 66 kHz, PixClock max 175 MHz
[ 6.337] (II) intel(0): EDID (in hex):
[ 6.337] (II) intel(0): 00ffffffffffff00367f250001010101
[ 6.337] (II) intel(0): 18160104a51d1078020f159a564b8b26
[ 6.337] (II) intel(0): 205054000000d1c00101010101010101
[ 6.337] (II) intel(0): 0101010101019c3f803172380f402020
[ 6.337] (II) intel(0): 330023a4100000180727806971380f40
[ 6.337] (II) intel(0): 2020330023a410000018000000fc0053
[ 6.337] (II) intel(0): 6f6e79204c43440a20202020000000fd
[ 6.337] (II) intel(0): 00273d2b4211000a2020202020200013
[ 6.337] (II) intel(0): EDID vendor "MS_", prod id 37
[ 6.337] (II) intel(0): Using EDID range info for horizontal sync
[ 6.337] (II) intel(0): Using EDID range info for vertical refresh
[ 6.337] (II) intel(0): Printing DDC gathered Modelines:
[ 6.337] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 6.337] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 6.337] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 6.337] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 6.337] (II) intel(0): Printing probed modes for output eDP1
[ 6.337] (II) intel(0): Modeline "1920x1080"x59.9 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz UeP)
[ 6.337] (II) intel(0): Modeline "1920x1080"x40.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 6.338] (II) intel(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[ 6.338] (II) intel(0): Modeline "1680x945"x60.0 131.48 1680 1784 1960 2240 945 946 949 978 -hsync +vsync (58.7 kHz)
[ 6.338] (II) intel(0): Modeline "1400x1050"x60.0 122.00 1400 1488 1640 1880 1050 1052 1064 1082 +hsync +vsync (64.9 kHz d)
[ 6.338] (II) intel(0): Modeline "1400x1050"x60.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 6.338] (II) intel(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 6.338] (II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 6.338] (II) intel(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 6.338] (II) intel(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 6.338] (II) intel(0): Modeline "1366x768"x60.0 85.89 1366 1439 1583 1800 768 769 772 795 -hsync +vsync (47.7 kHz)
[ 6.338] (II) intel(0): Modeline "1360x768"x60.0 85.50 1360 1424 1536 1792 768 771 777 795 +hsync +vsync (47.7 kHz e)
[ 6.338] (II) intel(0): Modeline "1280x800"x59.8 83.50 1280 1352 1480 1680 800 803 809 831 +hsync -vsync (49.7 kHz e)
[ 6.338] (II) intel(0): Modeline "1280x768"x59.9 79.50 1280 1344 1472 1664 768 771 778 798 -hsync +vsync (47.8 kHz e)
[ 6.338] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 6.338] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 6.338] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d)
[ 6.338] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 6.343] (II) intel(0): EDID for output VGA1
[ 6.343] (II) intel(0): Printing probed modes for output VGA1
[ 6.343] (II) intel(0): Modeline "1920x1200_60.00"x59.9 193.25 1920 2056 2256 2592 1200 1203 1209 1245 -hsync +vsync (74.6 kHz UP)
[ 6.343] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 6.344] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 6.344] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 6.344] (II) intel(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e)
[ 6.344] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz e)
[ 6.344] (II) intel(0): EDID for output HDMI1
[ 6.386] (II) intel(0): EDID for output DP1
[ 6.386] (II) intel(0): Output eDP1 connected
[ 6.386] (II) intel(0): Output VGA1 connected
[ 6.386] (II) intel(0): Output HDMI1 disconnected
[ 6.386] (II) intel(0): Output DP1 disconnected
[ 6.386] (II) intel(0): Using user preference for initial modes
[ 6.386] (II) intel(0): Output eDP1 using initial mode 1920x1080
[ 6.386] (II) intel(0): Output VGA1 using initial mode 1920x1200_60.00
[ 6.386] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 6.386] (**) intel(0): Display dimensions: (290, 160) mm
[ 6.386] (**) intel(0): DPI set to (336, 190)
[ 6.386] (II) Loading sub module "dri2"
[ 6.386] (II) LoadModule: "dri2"
[ 6.387] (II) Module "dri2" already built-in
[ 6.387] (==) Depth 24 pixmap format is 32 bpp
[ 6.387] (II) intel(0): SNA initialized with IvyBridge backend
[ 6.387] (==) intel(0): Backing store disabled
[ 6.387] (==) intel(0): Silken mouse enabled
[ 6.387] (II) intel(0): HW Cursor enabled
[ 6.387] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6.388] (==) intel(0): DPMS enabled
[ 6.388] (II) intel(0): [DRI2] Setup complete
[ 6.388] (II) intel(0): [DRI2] DRI driver: i965
[ 6.388] (II) intel(0): direct rendering: DRI2 Enabled
[ 6.388] (WW) intel(0): Option "PreferredMode" is not used
[ 6.388] (WW) intel(0): Option "Primary" is not used
[ 6.388] (WW) intel(0): Option "Position" is not used
[ 6.388] (==) intel(0): hotplug detection: "enabled"
[ 6.388] (--) RandR disabled
[ 6.410] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 6.410] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 6.410] (II) AIGLX: enabled GLX_ARB_create_context
[ 6.410] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 6.410] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 6.410] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 6.410] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 6.410] (II) AIGLX: Loaded and initialized i965
[ 6.410] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 6.411] (II) intel(0): switch to mode 1920x1080 on crtc 3 (pipe 0)
[ 6.500] (II) intel(0): switch to mode 1920x1200 on crtc 5 (pipe 1)
[ 6.663] (II) intel(0): Setting screen physical size to 1016 x 317
[ 6.703] (II) config/udev: Adding input device Video Bus (/dev/input/event10)
[ 6.703] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 6.703] (II) LoadModule: "evdev"
[ 6.704] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 6.706] (II) Module evdev: vendor="X.Org Foundation"
[ 6.706] compiled for 1.13.0, module version = 2.7.3
[ 6.706] Module class: X.Org XInput Driver
[ 6.706] ABI class: X.Org XInput driver, version 18.0
[ 6.706] (II) Using input driver 'evdev' for 'Video Bus'
[ 6.706] (**) Video Bus: always reports core events
[ 6.706] (**) evdev: Video Bus: Device: "/dev/input/event10"
[ 6.706] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 6.706] (--) evdev: Video Bus: Found keys
[ 6.706] (II) evdev: Video Bus: Configuring as keyboard
[ 6.706] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:09/input/input10/event10"
[ 6.706] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 6)
[ 6.706] (**) Option "xkb_rules" "evdev"
[ 6.706] (**) Option "xkb_model" "evdev"
[ 6.706] (**) Option "xkb_layout" "us"
[ 6.732] (II) config/udev: Adding input device Sony Vaio Keys (/dev/input/event3)
[ 6.732] (**) Sony Vaio Keys: Applying InputClass "evdev keyboard catchall"
[ 6.732] (II) Using input driver 'evdev' for 'Sony Vaio Keys'
[ 6.732] (**) Sony Vaio Keys: always reports core events
[ 6.732] (**) evdev: Sony Vaio Keys: Device: "/dev/input/event3"
[ 6.732] (--) evdev: Sony Vaio Keys: Vendor 0x104d Product 0
[ 6.732] (--) evdev: Sony Vaio Keys: Found keys
[ 6.732] (II) evdev: Sony Vaio Keys: Configuring as keyboard
[ 6.732] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/SNY5001:00/input/input3/event3"
[ 6.732] (II) XINPUT: Adding extended input device "Sony Vaio Keys" (type: KEYBOARD, id 7)
[ 6.732] (**) Option "xkb_rules" "evdev"
[ 6.732] (**) Option "xkb_model" "evdev"
[ 6.732] (**) Option "xkb_layout" "us"
[ 6.732] (II) config/udev: Adding input device Sony Vaio Jogdial (/dev/input/event4)
[ 6.732] (II) No input driver specified, ignoring this device.
[ 6.732] (II) This device may have been added with another device file.
[ 6.733] (II) config/udev: Adding input device Sony Vaio Jogdial (/dev/input/mouse0)
[ 6.733] (II) No input driver specified, ignoring this device.
[ 6.733] (II) This device may have been added with another device file.
[ 6.733] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 6.733] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 6.733] (II) Using input driver 'evdev' for 'Power Button'
[ 6.733] (**) Power Button: always reports core events
[ 6.733] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 6.733] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 6.733] (--) evdev: Power Button: Found keys
[ 6.733] (II) evdev: Power Button: Configuring as keyboard
[ 6.733] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event2"
[ 6.733] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 6.733] (**) Option "xkb_rules" "evdev"
[ 6.733] (**) Option "xkb_model" "evdev"
[ 6.733] (**) Option "xkb_layout" "us"
[ 6.733] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 6.733] (II) No input driver specified, ignoring this device.
[ 6.733] (II) This device may have been added with another device file.
[ 6.733] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 6.734] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event6)
[ 6.734] (II) No input driver specified, ignoring this device.
[ 6.734] (II) This device may have been added with another device file.
[ 6.734] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event7)
[ 6.734] (II) No input driver specified, ignoring this device.
[ 6.734] (II) This device may have been added with another device file.
[ 6.735] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event8)
[ 6.735] (II) No input driver specified, ignoring this device.
[ 6.735] (II) This device may have been added with another device file.
[ 6.735] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 6.735] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 6.735] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 6.735] (**) AT Translated Set 2 keyboard: always reports core events
[ 6.735] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 6.735] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 6.735] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 6.735] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 6.735] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 6.735] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[ 6.735] (**) Option "xkb_rules" "evdev"
[ 6.735] (**) Option "xkb_model" "evdev"
[ 6.735] (**) Option "xkb_layout" "us"
[ 6.736] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event9)
[ 6.736] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[ 6.736] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 6.736] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons"
[ 6.736] (II) LoadModule: "synaptics"
[ 6.737] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 6.738] (II) Module synaptics: vendor="X.Org Foundation"
[ 6.738] compiled for 1.13.0, module version = 1.6.2
[ 6.738] Module class: X.Org XInput Driver
[ 6.738] ABI class: X.Org XInput driver, version 18.0
[ 6.738] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 6.738] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 6.738] (**) Option "Device" "/dev/input/event9"
[ 6.740] (II) synaptics: SynPS/2 Synaptics TouchPad: found clickpad property
[ 6.740] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5768
[ 6.740] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4758
[ 6.740] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 6.740] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 6.740] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left double triple
[ 6.740] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 6.740] (**) Option "FingerLow" "35"
[ 6.740] (**) Option "FingerHigh" "45"
[ 6.740] (**) Option "ClickPad" "true"
[ 6.740] (**) Option "EmulateMidButtonTime" "0"
[ 6.740] (**) Option "HorizTwoFingerScroll" "on"
[ 6.740] (**) Option "TapButton1" "1"
[ 6.740] (**) Option "TapButton2" "2"
[ 6.740] (**) Option "TapButton3" "3"
[ 6.740] (**) Option "SoftButtonAreas" "50% 0 82% 0 0 0 0 0"
[ 6.740] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 6.740] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 6.740] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input9/event9"
[ 6.740] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 10)
[ 6.741] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 6.741] (**) synaptics: SynPS/2 Synaptics TouchPad: MaxSpeed is now 1.75
[ 6.741] (**) synaptics: SynPS/2 Synaptics TouchPad: AccelFactor is now 0.037
[ 6.741] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 6.741] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 6.741] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 6.741] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 6.741] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 6.742] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[ 6.742] (II) No input driver specified, ignoring this device.
[ 6.742] (II) This device may have been added with another device file.
[ 6.742] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[ 6.742] (II) No input driver specified, ignoring this device.
[ 6.742] (II) This device may have been added with another device file.
[ 6.747] removing GPU device /sys/devices/pci0000:00/0000:00:02.0/drm/card0 21764432
[ 6.747] xf86: remove device 0 /sys/devices/pci0000:00/0000:00:02.0/drm/card0
[ 6.747] failed to find screen to remove
[ 6.747] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 6.747] removing GPU device /sys/devices/pci0000:00/0000:00:02.0/drm/card0/card0-eDP-1 0
[ 6.747] removing GPU device /sys/devices/pci0000:00/0000:00:02.0/drm/card0/card0-VGA-1 0
[ 6.747] (II) config/udev: removing device Video Bus
[ 6.773] (II) evdev: Video Bus: Close
[ 6.773] (II) UnloadModule: "evdev"
[ 6.773] (II) config/udev: Adding input device Video Bus (/dev/input/event10)
[ 6.773] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 6.773] (II) Using input driver 'evdev' for 'Video Bus'
[ 6.773] (**) Video Bus: always reports core events
[ 6.773] (**) evdev: Video Bus: Device: "/dev/input/event10"
[ 6.773] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 6.773] (--) evdev: Video Bus: Found keys
[ 6.773] (II) evdev: Video Bus: Configuring as keyboard
[ 6.773] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:09/input/input10/event10"
[ 6.773] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 6)
[ 6.773] (**) Option "xkb_rules" "evdev"
[ 6.773] (**) Option "xkb_model" "evdev"
[ 6.773] (**) Option "xkb_layout" "us"
[ 6.774] removing GPU device /sys/devices/pci0000:00/0000:00:02.0/drm/card0/card0-HDMI-A-1 0
[ 6.774] removing GPU device /sys/devices/pci0000:00/0000:00:02.0/drm/card0/card0-DP-1 0
[ 7.569] (II) config/udev: Adding input device USB2.0 Camera (/dev/input/event11)
[ 7.569] (**) USB2.0 Camera: Applying InputClass "evdev keyboard catchall"
[ 7.569] (II) Using input driver 'evdev' for 'USB2.0 Camera'
[ 7.569] (**) USB2.0 Camera: always reports core events
[ 7.569] (**) evdev: USB2.0 Camera: Device: "/dev/input/event11"
[ 7.569] (--) evdev: USB2.0 Camera: Vendor 0x5ca Product 0x18c6
[ 7.569] (--) evdev: USB2.0 Camera: Found keys
[ 7.569] (II) evdev: USB2.0 Camera: Configuring as keyboard
[ 7.569] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input11/event11"
[ 7.569] (II) XINPUT: Adding extended input device "USB2.0 Camera" (type: KEYBOARD, id 11)
[ 7.569] (**) Option "xkb_rules" "evdev"
[ 7.569] (**) Option "xkb_model" "evdev"
[ 7.569] (**) Option "xkb_layout" "us"
[ 24.939] (II) intel(0): EDID vendor "MS_", prod id 37
[ 24.939] (II) intel(0): Using hsync ranges from config file
[ 24.939] (II) intel(0): Using vrefresh ranges from config file
[ 24.939] (II) intel(0): Printing DDC gathered Modelines:
[ 24.939] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 24.939] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 24.939] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 24.989] (II) intel(0): switch to mode 1920x1080 on crtc 3 (pipe 0)
[ 25.055] (II) intel(0): EDID vendor "MS_", prod id 37
[ 25.055] (II) intel(0): Using hsync ranges from config file
[ 25.055] (II) intel(0): Using vrefresh ranges from config file
[ 25.055] (II) intel(0): Printing DDC gathered Modelines:
[ 25.055] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 25.055] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 25.055] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 25.150] (II) intel(0): EDID vendor "MS_", prod id 37
[ 25.150] (II) intel(0): Using hsync ranges from config file
[ 25.150] (II) intel(0): Using vrefresh ranges from config file
[ 25.150] (II) intel(0): Printing DDC gathered Modelines:
[ 25.150] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 25.150] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 25.150] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 25.274] (II) intel(0): EDID vendor "MS_", prod id 37
[ 25.274] (II) intel(0): Using hsync ranges from config file
[ 25.274] (II) intel(0): Using vrefresh ranges from config file
[ 25.274] (II) intel(0): Printing DDC gathered Modelines:
[ 25.274] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 25.274] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 25.274] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 25.387] (II) intel(0): EDID vendor "MS_", prod id 37
[ 25.387] (II) intel(0): Using hsync ranges from config file
[ 25.387] (II) intel(0): Using vrefresh ranges from config file
[ 25.387] (II) intel(0): Printing DDC gathered Modelines:
[ 25.387] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 25.387] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 25.387] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 25.518] (II) intel(0): EDID vendor "MS_", prod id 37
[ 25.518] (II) intel(0): Using hsync ranges from config file
[ 25.518] (II) intel(0): Using vrefresh ranges from config file
[ 25.518] (II) intel(0): Printing DDC gathered Modelines:
[ 25.518] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 25.518] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 25.518] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 25.676] (II) intel(0): EDID vendor "MS_", prod id 37
[ 25.676] (II) intel(0): Using hsync ranges from config file
[ 25.676] (II) intel(0): Using vrefresh ranges from config file
[ 25.676] (II) intel(0): Printing DDC gathered Modelines:
[ 25.676] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 25.676] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 25.676] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 29.373] (II) config/udev: Adding input device Bluetooth Laser Travel Mouse (/dev/input/mouse2)
[ 29.373] (II) No input driver specified, ignoring this device.
[ 29.373] (II) This device may have been added with another device file.
[ 29.373] (II) config/udev: Adding input device Bluetooth Laser Travel Mouse (/dev/input/event12)
[ 29.373] (**) Bluetooth Laser Travel Mouse: Applying InputClass "evdev pointer catchall"
[ 29.373] (II) Using input driver 'evdev' for 'Bluetooth Laser Travel Mouse'
[ 29.373] (**) Bluetooth Laser Travel Mouse: always reports core events
[ 29.373] (**) evdev: Bluetooth Laser Travel Mouse: Device: "/dev/input/event12"
[ 29.373] (--) evdev: Bluetooth Laser Travel Mouse: Vendor 0x46d Product 0xb008
[ 29.373] (--) evdev: Bluetooth Laser Travel Mouse: Found 12 mouse buttons
[ 29.373] (--) evdev: Bluetooth Laser Travel Mouse: Found scroll wheel(s)
[ 29.373] (--) evdev: Bluetooth Laser Travel Mouse: Found relative axes
[ 29.373] (--) evdev: Bluetooth Laser Travel Mouse: Found x and y relative axes
[ 29.374] (II) evdev: Bluetooth Laser Travel Mouse: Configuring as mouse
[ 29.374] (II) evdev: Bluetooth Laser Travel Mouse: Adding scrollwheel support
[ 29.374] (**) evdev: Bluetooth Laser Travel Mouse: YAxisMapping: buttons 4 and 5
[ 29.374] (**) evdev: Bluetooth Laser Travel Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 29.374] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/bluetooth/hci0/hci0:33/input12/event12"
[ 29.374] (II) XINPUT: Adding extended input device "Bluetooth Laser Travel Mouse" (type: MOUSE, id 12)
[ 29.374] (II) evdev: Bluetooth Laser Travel Mouse: initialized for relative axes.
[ 29.374] (**) Bluetooth Laser Travel Mouse: (accel) keeping acceleration scheme 1
[ 29.374] (**) Bluetooth Laser Travel Mouse: (accel) acceleration profile 0
[ 29.374] (**) Bluetooth Laser Travel Mouse: (accel) acceleration factor: 2.000
[ 29.374] (**) Bluetooth Laser Travel Mouse: (accel) acceleration threshold: 4
[ 589.381] (II) intel(0): EDID vendor "MS_", prod id 37
[ 589.381] (II) intel(0): Using hsync ranges from config file
[ 589.381] (II) intel(0): Using vrefresh ranges from config file
[ 589.381] (II) intel(0): Printing DDC gathered Modelines:
[ 589.381] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 589.381] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 589.381] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 589.433] (II) intel(0): switch to mode 1920x1080 on crtc 3 (pipe 0)
[ 1442.644] (II) intel(0): EDID vendor "MS_", prod id 37
[ 1442.644] (II) intel(0): Using hsync ranges from config file
[ 1442.644] (II) intel(0): Using vrefresh ranges from config file
[ 1442.644] (II) intel(0): Printing DDC gathered Modelines:
[ 1442.644]Hey all,
Here is the issue:
I have sony svz13114gxx laptop with xfce4 DE, i just tried to hook up external vga monitor to laptop and everything configures right with this run in normal session:
[code]
xrandr --output eDP1 --mode 1920x1080
xrandr --newmode "1920x1200_60.00" 193.25 1920 2056 2256 2592 1200 1203 1209 1245 -hsync +vsync
xrandr --addmode VGA1 1920x1200_60.00
xrandr --output VGA1 --mode 1920x1200_60.00
xrandr --output VGA1 --left-of eDP1
[/code]
Obviously when i reboot this is not persistent, so then i put this stuff in my /etc/X11/xorg.conf.d/20-intel.conf:
[code]
Section "Device"
Identifier "Intel Graphics"
Driver "intel"
Option "AccelMethod" "sna"
Option "monitor-eDP1" "eDP1"
Option "monitor-VGA1" "VGA1"
EndSection
Section "Monitor"
Identifier "VGA1"
Modeline "1920x1200_60.00" 193.25 1920 2056 2256 2592 1200 1203 1209 1245 -HSync +VSync
Option "PreferredMode" "1920x1200_60.00"
EndSection
Section "Monitor"
Identifier "eDP1"
Option "PreferredMode" "1920x1080"
Option "Primary" "true"
Option "Position" "1920 0"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Intel Graphics"
Monitor "eDP1"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection[/code]
This is where the problems start. On reboot Slim desktop manager seems to be stretched properly across the two monitors, but the I login and the display switches back to being mirrored, my xfce gtk2 theme is disabled in favor of somee default looking one, my icons are back to default, and none of my custom keyboard shorcuts work.
I can then use xrandr to get the displays in extended mode again, but the themes and icons etc do not revert. And on reboot, i have the same issue.
I have tried the sourcing ~/.xprofile, ~/.xinitrc, and ~/.config.xfce4/xinitrc routes, putting the xrandr cammands above the exec lines and that doesn't even enable VGA1.
I have been to all these places
[code]
https://wiki.ubuntu.com/X/Config/Resolution#Xrandr_Graphical_Front_End_GUI
http://ilkinbalkanay.blogspot.com/2008/01/extended-desktop-configuration-with.html
https://bbs.archlinux.org/viewtopic.php?id=98747
https://www.google.com/search?q=arch%20xrandr&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a&source=hp&channel=np
https://wiki.archlinux.org/index.php/Execute_commands_after_X_start
http://intellinuxgraphics.org/dualhead.html
http://mac.linux.be/content/setting-xorgconf-manually-xrandr#3
https://www.google.com/search?q=arch%20dual%20monitors%20The%20last%20active%20output%20must%20not%20be%20disabled%2C%20the%20system%20would%20be%20unusable.&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a&source=hp&channel=np#hl=en&safe=off&client=firefox-a&tbo=d&rls=org.mozilla:en-US%3Aofficial&channel=np&sclient=psy-ab&q=xfce+%22Selected+output+not+disabled%22&oq=xfce+%22Selected+output+not+disabled%22&gs_l=serp.3...1694.1694.3.2205.1.1.0.0.0.0.97.97.1.1.0.les%3Bcrnk_timediscounta..0.0...1c.1.O4EDj7DaWlA&pbx=1&fp=1&bpcl=39468505&biw=984&bih=936&cad=b&sei=aKC_UIKvJ6GA0AGTg4HwBg&sei=FKS_UMuwJdPU0gHorICQBA&bav=on.2,or.r_gc.r_pw.r_qf.&sei=2MK_UOaAJ5Ph0wGbsoHICg
https://wiki.archlinux.org/index.php/Xfce#Customizing_Startup_Applications
http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/x-config.html
https://wiki.archlinux.org/index.php/Xorg#Monitor_settings
[/code]
Even after much research, still no luck.
this might be useful:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=631225
Anyone have any ideas?
here is my Xorg0.log
[code]
[ 3.490]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 3.490] X Protocol Version 11, Revision 0
[ 3.490] Build Operating System: Linux 3.6.3-1-ARCH x86_64
[ 3.490] Current Operating System: Linux tcz 3.6.8-1-ARCH #1 SMP PREEMPT Mon Nov 26 22:10:40 CET 2012 x86_64
[ 3.490] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=d23251af-35fa-426b-a7d5-5aa2f0a5b87d ro quiet pcie_aspm=force i915.i915_enable_rc6=1
[ 3.490] Build Date: 08 November 2012 07:09:29PM
[ 3.490]
[ 3.490] Current version of pixman: 0.28.0
[ 3.490] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 3.490] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 3.490] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Dec 5 16:25:21 2012
[ 3.492] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 3.494] (==) No Layout section. Using the first Screen section.
[ 3.494] (**) |-->Screen "Default Screen" (0)
[ 3.494] (**) | |-->Monitor "eDP1"
[ 3.494] (**) | |-->Device "Intel Graphics"
[ 3.494] (==) Automatically adding devices
[ 3.494] (==) Automatically enabling devices
[ 3.494] (==) Automatically adding GPU devices
[ 3.504] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 3.504] Entry deleted from font path.
[ 3.504] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 3.504] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 3.504] Entry deleted from font path.
[ 3.504] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 3.504] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Type1/
[ 3.504] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 3.504] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 3.504] (II) Loader magic: 0x7fcc40
[ 3.504] (II) Module ABI versions:
[ 3.504] X.Org ANSI C Emulation: 0.4
[ 3.504] X.Org Video Driver: 13.1
[ 3.504] X.Org XInput driver : 18.0
[ 3.504] X.Org Server Extension : 7.0
[ 3.505] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 6.276] (--) PCI:*(0:0:2:0) 8086:0166:104d:90a5 rev 9, Mem @ 0xd7000000/4194304, 0xc0000000/268435456, I/O @ 0x00009000/64
[ 6.276] (II) Open ACPI successful (/var/run/acpid.socket)
[ 6.276] Initializing built-in extension Generic Event Extension
[ 6.276] Initializing built-in extension SHAPE
[ 6.276] Initializing built-in extension MIT-SHM
[ 6.276] Initializing built-in extension XInputExtension
[ 6.276] Initializing built-in extension XTEST
[ 6.276] Initializing built-in extension BIG-REQUESTS
[ 6.276] Initializing built-in extension SYNC
[ 6.276] Initializing built-in extension XKEYBOARD
[ 6.276] Initializing built-in extension XC-MISC
[ 6.276] Initializing built-in extension SECURITY
[ 6.276] Initializing built-in extension XINERAMA
[ 6.276] Initializing built-in extension XFIXES
[ 6.276] Initializing built-in extension RENDER
[ 6.276] Initializing built-in extension RANDR
[ 6.276] Initializing built-in extension COMPOSITE
[ 6.276] Initializing built-in extension DAMAGE
[ 6.276] Initializing built-in extension MIT-SCREEN-SAVER
[ 6.276] Initializing built-in extension DOUBLE-BUFFER
[ 6.276] Initializing built-in extension RECORD
[ 6.276] Initializing built-in extension DPMS
[ 6.276] Initializing built-in extension X-Resource
[ 6.276] Initializing built-in extension XVideo
[ 6.276] Initializing built-in extension XVideo-MotionCompensation
[ 6.276] Initializing built-in extension XFree86-VidModeExtension
[ 6.276] Initializing built-in extension XFree86-DGA
[ 6.276] Initializing built-in extension XFree86-DRI
[ 6.276] Initializing built-in extension DRI2
[ 6.276] (II) LoadModule: "glx"
[ 6.278] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 6.281] (II) Module glx: vendor="X.Org Foundation"
[ 6.281] compiled for 1.13.0, module version = 1.0.0
[ 6.281] ABI class: X.Org Server Extension, version 7.0
[ 6.281] (==) AIGLX enabled
[ 6.281] Loading extension GLX
[ 6.281] (II) LoadModule: "intel"
[ 6.281] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 6.285] (II) Module intel: vendor="X.Org Foundation"
[ 6.285] compiled for 1.13.0.901, module version = 2.20.14
[ 6.285] Module class: X.Org Video Driver
[ 6.285] ABI class: X.Org Video Driver, version 13.1
[ 6.285] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2),
Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2),
Haswell Server (GT2+), Haswell SDV Desktop (GT1),
Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+),
Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),
Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1),
Haswell SDV Server (GT2), Haswell SDV Server (GT2+),
Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),
Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1),
Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+),
Haswell ULT Server (GT1), Haswell ULT Server (GT2),
Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1),
Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+),
Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2),
Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1),
Haswell CRW Server (GT2), Haswell CRW Server (GT2+),
ValleyView PO board
[ 6.286] (++) using VT number 7
[ 6.288] (II) intel(0): using device path '/dev/dri/card0'
[ 6.288] (**) intel(0): Depth 24, (--) framebuffer bpp 32
[ 6.288] (==) intel(0): RGB weight 888
[ 6.288] (==) intel(0): Default visual is TrueColor
[ 6.288] (**) intel(0): Option "AccelMethod" "sna"
[ 6.288] (--) intel(0): Integrated Graphics Chipset: Intel(R) Ivybridge Mobile (GT2)
[ 6.289] (**) intel(0): Framebuffer tiled
[ 6.289] (**) intel(0): Pixmaps tiled
[ 6.289] (**) intel(0): 3D buffers tiled
[ 6.289] (**) intel(0): Throttling enabled
[ 6.289] (**) intel(0): Delayed flush enabled
[ 6.289] (**) intel(0): "Tear free" disabled
[ 6.289] (**) intel(0): Forcing per-crtc-pixmaps? no
[ 6.289] (II) intel(0): Output eDP1 using monitor section eDP1
[ 6.289] (**) intel(0): Option "PreferredMode" "1920x1080"
[ 6.289] (**) intel(0): Option "Position" "1920 0"
[ 6.289] (**) intel(0): Option "Primary" "true"
[ 6.289] (--) intel(0): found backlight control interface acpi_video0 (type 'firmware')
[ 6.293] (II) intel(0): Output VGA1 using monitor section VGA1
[ 6.293] (**) intel(0): Option "PreferredMode" "1920x1200_60.00"
[ 6.294] (II) intel(0): Output HDMI1 has no monitor section
[ 6.336] (II) intel(0): Output DP1 has no monitor section
[ 6.337] (II) intel(0): EDID for output eDP1
[ 6.337] (II) intel(0): Manufacturer: MS_ Model: 25 Serial#: 16843009
[ 6.337] (II) intel(0): Year: 2012 Week: 24
[ 6.337] (II) intel(0): EDID Version: 1.4
[ 6.337] (II) intel(0): Digital Display Input
[ 6.337] (II) intel(0): 8 bits per channel
[ 6.337] (II) intel(0): Digital interface is DisplayPort
[ 6.337] (II) intel(0): Max Image Size [cm]: horiz.: 29 vert.: 16
[ 6.337] (II) intel(0): Gamma: 2.20
[ 6.337] (II) intel(0): No DPMS capabilities specified
[ 6.337] (II) intel(0): Supported color encodings: RGB 4:4:4
[ 6.337] (II) intel(0): First detailed timing is preferred mode
[ 6.337] (II) intel(0): Preferred mode is native pixel format and refresh rate
[ 6.337] (II) intel(0): redX: 0.602 redY: 0.336 greenX: 0.296 greenY: 0.546
[ 6.337] (II) intel(0): blueX: 0.148 blueY: 0.126 whiteX: 0.313 whiteY: 0.329
[ 6.337] (II) intel(0): Manufacturer's mask: 0
[ 6.337] (II) intel(0): Supported standard timings:
[ 6.337] (II) intel(0): #0: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 6.337] (II) intel(0): Supported detailed timing:
[ 6.337] (II) intel(0): clock: 162.8 MHz Image Size: 291 x 164 mm
[ 6.337] (II) intel(0): h_active: 1920 h_sync: 1952 h_sync_end 1984 h_blank_end 2481 h_border: 0
[ 6.337] (II) intel(0): v_active: 1080 v_sync: 1083 v_sync_end 1086 v_blanking: 1095 v_border: 0
[ 6.337] (II) intel(0): Supported detailed timing:
[ 6.337] (II) intel(0): clock: 99.9 MHz Image Size: 291 x 164 mm
[ 6.337] (II) intel(0): h_active: 1920 h_sync: 1952 h_sync_end 1984 h_blank_end 2281 h_border: 0
[ 6.337] (II) intel(0): v_active: 1080 v_sync: 1083 v_sync_end 1086 v_blanking: 1095 v_border: 0
[ 6.337] (II) intel(0): Monitor name: Sony LCD
[ 6.337] (II) intel(0): Ranges: V min: 39 V max: 61 Hz, H min: 43 H max: 66 kHz, PixClock max 175 MHz
[ 6.337] (II) intel(0): EDID (in hex):
[ 6.337] (II) intel(0): 00ffffffffffff00367f250001010101
[ 6.337] (II) intel(0): 18160104a51d1078020f159a564b8b26
[ 6.337] (II) intel(0): 205054000000d1c00101010101010101
[ 6.337] (II) intel(0): 0101010101019c3f803172380f402020
[ 6.337] (II) intel(0): 330023a4100000180727806971380f40
[ 6.337] (II) intel(0): 2020330023a410000018000000fc0053
[ 6.337] (II) intel(0): 6f6e79204c43440a20202020000000fd
[ 6.337] (II) intel(0): 00273d2b4211000a2020202020200013
[ 6.337] (II) intel(0): EDID vendor "MS_", prod id 37
[ 6.337] (II) intel(0): Using EDID range info for horizontal sync
[ 6.337] (II) intel(0): Using EDID range info for vertical refresh
[ 6.337] (II) intel(0): Printing DDC gathered Modelines:
[ 6.337] (II) intel(0): Modeline "1920x1080"x0.0 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz eP)
[ 6.337] (II) intel(0): Modeline "1920x1080"x0.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 6.337] (II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz e)
[ 6.337] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 6.337] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 6.337] (II) intel(0): Printing probed modes for output eDP1
[ 6.337] (II) intel(0): Modeline "1920x1080"x59.9 162.84 1920 1952 1984 2481 1080 1083 1086 1095 -hsync -vsync (65.6 kHz UeP)
[ 6.337] (II) intel(0): Modeline "1920x1080"x40.0 99.91 1920 1952 1984 2281 1080 1083 1086 1095 -hsync -vsync (43.8 kHz e)
[ 6.338] (II) intel(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[ 6.338] (II) intel(0): Modeline "1680x945"x60.0 131.48 1680 1784 1960 2240 945 946 949 978 -hsync +vsync (58.7 kHz)
[ 6.338] (II) intel(0): Modeline "1400x1050"x60.0 122.00 1400 1488 1640 1880 1050 1052 1064 1082 +hsync +vsync (64.9 kHz d)
[ 6.338] (II) intel(0): Modeline "1400x1050"x60.0 121.75 1400 1488 1632 1864 1050 1053 1057 1089 -hsync +vsync (65.3 kHz e)
[ 6.338] (II) intel(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 6.338] (II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 6.338] (II) intel(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e)
[ 6.338] (II) intel(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 6.338] (II) intel(0): Modeline "1366x768"x60.0 85.89 1366 1439 1583 1800 768 769 772 795 -hsync +vsync (47.7 kHz)
[ 6.338] (II) intel(0): Modeline "1360x768"x60.0 85.50 1360 1424 1536 1792 768 771 777 795 +hsync +vsync (47.7 kHz e)
[ 6.338] (II) intel(0): Modeline "1280x800"x59.8 83.50 1280 1352 1480 1680 800 803 809 831 +hsync -vsync (49.7 kHz e)
[ 6.338] (II) intel(0): Modeline "1280x768"x59.9 79.50 1280 1344 1472 1664 768 771 778 798 -hsync +vsync (47.8 kHz e)
[ 6.338] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 6.338] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 6.338] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d)
[ 6.338] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 6.343] (II) intel(0): EDID for output VGA1
[ 6.343] (II) intel(0): Printing probed modes for output VGA1
[ 6.343] (II) intel(0): Modeline "1920x1200_60.00"x59.9 193.25 1920 2056 2256 2592 1200 1203 1209 1245 -hsync +vsync (74.6 kHz UP)
[ 6.343] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 6.344] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 6.344] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 6.344] (II) intel(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e)
[ 6.344] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz e)
[ 6.344] (II) intel(0): EDID for output HDMI1
[ 6.386] (II) intel(0): EDID for output DP1
[ 6.386] (II) intel(0): Output eDP1 connected
[ 6.386] (II) intel(0): Output VGA1 connected
[ 6.386] (II) intel(0): Output HDMI1 disconnected
[ 6.386] (II) intel(0): Output DP1 disconnected
[ 6.386] (II) intel(0): Using user preference for initial modes
[ 6.386] (II) intel(0): Output eDP1 using initial mode 1920x1080
[ 6.386] (II) intel(0): Output VGA1 using initial mode 1920x1200_60.00
[ 6.386] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 6.386] (**) intel(0): Display dimensions: (290, 160) mm
[ 6.386] (**) intel(0): DPI set to (336, 190)
[ 6.386] (II) Loading sub module "dri2"
[ 6.386] (II) LoadModule: "dri2"
[ 6.387] (II) Module "dri2" already built-in
[ 6.387] (==) Depth 24 pixmap format is 32 bpp
[ 6.387] (II) intel(0): SNA initialized with IvyBridge backend
[ 6.387] (==) intel(0): Backing store disabled
[ 6.387] (==) intel(0): Silken mouse enabled
[ 6.387] (II) intel(0): HW Cursor enabled
[ 6.387] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6.388] (==) intel(0): DPMS enabled
[ 6.388] (II) intel(0): [DRI2] Setup complete
[ 6.388] (II) intel(0): [DRI2] DRI driver: i965
[ 6.388] (II) intel(0): direct rendering: DRI2 Enabled
[ 6.388] (WW) intel(0): Option "PreferredMode" is not used
[ 6.388] (WW) intel(0): Option "Primary" is not used
[ 6.388] (WW) intel(0): Option "Position" is not used
[ 6.388] (==) intel(0): hotplug detection: "enabled"
[ 6.388] (--) RandR disabled
[ 6.410] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 6.410] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 6.410] (II) AIGLX: enabled GLX_ARB_create_context
[ 6.410] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 6.410] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 6.410] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 6.410] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 6.410] (II) AIGLX: Loaded and initialized i965
[ 6.410] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 6.411] (II) intel(0): switch to mode 1920x1080 on crtc 3 (pipe 0)
[ 6.500] (II) intel(0): switch to mode 1920x1200 on crtc 5 (pipe 1)
[ 6.663] (II) intel(0): Setting screen physical size to 1016 x 317
[ 6.703] (II) config/udev: Adding input device Video Bus (/dev/input/event10)
[ 6.703] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 6.703] (II) LoadModule: "evdev"
[ 6.704] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 6.706] (II) Module evdev: vendor="X.Org Foundation"
[ 6.706] compiled for 1.13.0, module version = 2.7.3
[ 6.706] Module class: X.Org XInput Driver
[ 6.706] ABI class: X.Org XInput driver, version 18.0
[ 6.706] (II) Using input driver 'evdev' for 'Video Bus'
[ 6.706] (**) Video Bus: always reports core events
[ 6.706] (**) evdev: Video Bus: Device: "/dev/input/event10"
[ 6.706] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 6.706] (--) evdev: Video Bus: Found keys
[ 6.706] (II) evdev: Video Bus: Configuring as keyboard
[ 6.706] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:09/input/input10/event10"
[ 6.706] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 6)
[ 6.706] (**) Option "xkb_rules" "evdev"
[ 6.706] (**) Option "xkb_model" "evdev"
[ 6.706] (**) Option "xkb_layout" "us"
[ 6.732] (II) config/udev: Adding input device Sony Vaio Keys (/dev/input/event3)
[ 6.732] (**) Sony Vaio Keys: Applying InputClass "evdev keyboard catchall"
[ 6.732] (II) Using input driver 'evdev' for 'Sony Vaio Keys'
[ 6.732] (**) Sony Vaio Keys: always reports core events
[ 6.732] (**) evdev: Sony Vaio Keys: Device: "/dev/input/event3"
[ 6.732] (--) evdev: Sony Vaio Keys: Vendor 0x104d Product 0
[ 6.732] (--) evdev: Sony Vaio Keys: Found keys
[ 6.732] (II) evdev: Sony Vaio Keys: Configuring as keyboard
[ 6.732] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/SNY5001:00/input/input3/event3"
[ 6.732] (II) XINPUT: Adding extended input device "Sony Vaio Keys" (type: KEYBOARD, id 7)
[ 6.732] (**) Option "xkb_rules" "evdev"
[ 6.732] (**) Option "xkb_model" "evdev"
[ 6.732] (**) Option "xkb_layout" "us"
[ 6.732] (II) config/udev: Adding input device Sony Vaio Jogdial (/dev/input/event4)
[ 6.732] (II) No input driver specified, ignoring this device.
[ 6.732] (II) This device may have been added with another device file.
[ 6.733] (II) config/udev: Adding input device Sony Vaio Jogdial (/dev/input/mouse0)
[ 6.733] (II) No input driver specified, ignoring this device.
[ 6.733] (II) This device may have been added with another device file.
[ 6.733] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 6.733] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 6.733] (II) Using input driver 'evdev' for 'Power Button'
[ 6.733] (**) Power Button: always reports core events
[ 6.733] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 6.733] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 6.733] (--) evdev: PowerHave you ever tried 'arandr'? It's a GUI for xrandr; it could be useful.
I used this config with nouveau, now I've successfully created my xorg.conf with nvidia blobs, but this one worked~
Section "Device"
Identifier "NVIDIA GeForce GT320"
Driver "nouveau"
Option "Monitor-DVI-I-1" "BENQ G2450"
Option "Monitor-HDMI-1" "LG W2442PA"
EndSection
Section "Monitor"
Identifier "BENQ G2450"
Option "Primary" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
Option "Position" "1080 612"
EndSection
Section "Monitor"
Identifier "LG W2442PA"
Option "LeftOf" "BENQ G2450"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "59.9"
Option "Position" "0 0"
Option "Rotate" "Left"
EndSection
Section "Screen"
Identifier "Primary Screen"
Device "NVIDIA GeForce GT320"
Monitor "BENQ G2450"
DefaultDepth 24
SubSection "Display"
Depth 24
Virtual 3000 1920
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Primary Screen"
EndSection
I'm using XFCE as well, 2 monitors, the left one rotated 90º. The main difference it's that I've the 'Virtual' option inside 'SubSection'; not sure if it's relevant. -
(solved) get X to use my PCI card instead of onboard graphics.
I'm trying to install arch on an old P4 dell (dimension 2350) and given the specific requirements and restrictions of this given beast I'm having a bit of trouble getting X configured. (I'm turning it into a replacement for my modded xbox running xbmc, yes, I know it won't play hi-def)
Here's the setup:
- It has onboard graphics (intel) which I don't plan on using since it only has vga out.
- I've installed my video card (ATI radeon 9250 - hey it's the best standard pci card I could find)
Here's the problem:
- Everything works with the onboard intel chip
- If I try to plug my monitor in to the ATI card it (the monitor) dims and doesn't register as being attached.\
- I've tried turning off the onboard graphics in my bios but the only options are "onboard" and "auto" so it's currently set to auto.
More fun:
- The fun part is that I plan on using the ATI card's svideo out to my tv once it's set up, I'm just trying to get the monitor to work while I configure everything.
I'm considering trying to run an ubuntu live disc and seeing if I can copy over the xorg.conf file that gets generated.
Any ideas?
**edit
After some searching I've got it working. Apparently linux still reads onboard cards with this pc/bios because of the piss poor bios.
i added 'blacklist agpgart' & 'blacklist intel_agp' (without quotes) to /etc/modprobe.d/blacklist, set video to 'auto' in the bios, plugged the monitor into my card and rebooted.
sweet.
Last edited by ctarwater (2009-04-05 00:44:18)Oh my God -.- I had that page open, read through it but I didn't realized that my solution was written there
Thanks very much!! It worked :-)
Maybe you are looking for
-
Error while executing file in Background
Hi All, I need to schedule a job in background.where i need to read data from excel file. while executing in background mode its saying 'Error while reading file'. but in foreground i can able to execute it.can anybody help me out. Thanks Sudha
-
Does Acrobat X Standard Support "Edit Page Numbering Format"
In Acrobate X Pro, I can edit page numbers using the "Edit Page Numbering Format" feature. This is the icon in the Customize Quick Tools dialog box: One of my users wants to know if Acrobat X Standard supports that feature? Thanks!
-
Hi, I want to pass multiple tax codes in RFBIBL00. Currently my report only supports single tax code which is appearing first. How to do that./ Thanks
-
Running BizTalk on multiple non-clustered servers. Potential serious issue
Hi, I have just discovered what has potential to be a fairly large issue in our current BizTalk Architecture. We are running BizTalk Server 2006 R2 on 2 different servers, running Windows Server 2003 R2. These servers are NOT clustered. Instead, BizT
-
Premiere Elements 9, image sizing
I have been working on a 'slideshow' compiled from scanned pictures. Some of the early images were narrow & tall (approx 3 x 5). When these images are converted in Photoshop Elements to wmv files, imported into Premiere Elements, titles & menu added,