[SOLVED] GRUB Failing on Fresh Install

I'm trying to do a fresh install on a computer with an existing 20GB windows installation. I have done this for years with no problem, but now grub-mkconfig is returning errors (here's a photo - http://imgur.com/8Az66wx), and if I go ahead with grub-install afterwards, I find that there's no Windows boot option and trying to boot Linux also yields errors (see this photo - http://imgur.com/umfMznr). I've tried twice now with the same results. Any ideas what's going on? Thanks.
Last edited by tony5429 (2013-12-14 00:41:59)

Actually I did search a bit and found a lot of discussion about the error in cases where people were trying to use an LVM, and situations which returned errors but still allowed them to boot. My case is a bit different as I'm just using standard hard drive partitions, and Linux is not booting.

Similar Messages

  • [SOLVED] Grub failing to install on UEFI

    I am trying to do a fresh install on my desktop and am running into issues when installing grub. 
    My setup is: 3x500GB drives (sda1 is a 1GB partition for /boot/efi, sd[bc]1 raid 1 for swap, sd[abc]2 raid 5 with LVM for /, /home, and /tmp). ASUS m5a97 LE R2.0 motherboard.
    I am currently chroot into /mnt, where my / LVM is mounted, I have dm_mod loaded, and I was following the instructions here.
    I get an error from grub toward the end saying "Path  `/boot/grub' is not readable by GRUB on boot. Installation is impossile. Aborting."  (there's a LOT of output before that because of --debug. 
    I tried looking around, and I saw some people say that they had success with a fresh install when upgrading, but that doesn't really apply to me as this is already a fresh install.
    Does anyone have any ideas what could be causing this? Thanks in advance!
    David
    Last edited by slackcub (2013-07-28 08:17:30)

    slackcub wrote:Alright I figured I may as well update this.  I fell a little silly, but I do know at first the DVD was booting in UEFI mode, but apparently at some point that stopped, and that was what was causing all my issues.  I am now up and running and all good. Thanks for the help everyone!
    I find it a very good idea to keep something as /boot/EFI/boot/bootx64.efi (or \EFI\BOOT\BOOTX64.efi relative to the root of the ESP).  That is the "default" efi application.  It is what is run if you have your machine set to boot in UEFI mode and you choose the disk to boot from (rather than a firmware entry like those created by efibootmgr).  It was put into the spec so that one could boot a removable medium, like a USB flash drive or cdrom, with UEFI. Obviously, a removable whatever is not going to have a firmware entry for it, so there needed to be some kind of standardization on how to make those work.  From there, apparently that idea carried over to the internal devices as well, and now a vast majority of UEFI firmwares use this for all disks, not just removable ones.
    Nowadays, I keep gummiboot there.  But when I first started using UEFI, I kept the UEFI Shell v2 there since it that is probably the most versatile thing that could be used as a fallback.  But as long as you have somethign there, in the event that you lose all your firmware entries, this might save your ass.  In my Phoenix bios, the exit and save changes, you would use F10, while a total reset of the bios to defaults is F9... yeah, I reset my bios by accident once.  Having the UEFI Shell in that spot made my life quite a bit easier.

  • CFChart fails on fresh install

    We recently started the move from our old CF servers to the
    new CF8, and have been having some problems getting cfchart to
    display. No charts will display, unless I save them down to a file
    (manually) and link to that. After wrestling around with it and not
    getting anywhere, I tried installing a developer edition on my
    workstation to see if I could replicate the issue.
    With a basic single server developer installation under IIS,
    my cfcharting problems remained. With a fresh install, every flash
    graph I try displays a white rectangle, but the image graphs show
    up, I can still save down the generated graph to a file and display
    that ok. The files do appear in the c:\Coldfusion8\charting\cache
    directory when the chart page is hit.
    Is there some path that's munged on the install or that needs
    to be tweaked for charting to work? Is there an incompatibility
    with IIS6's default settings?
    Attached is my cfchart test script.
    Thanks!
    -Drew

    Windows 7 x64 all updates
    Just doublechecking. Does that include the recent chkdsk hotfixes?
    [The Chkdsk.exe program does not start correctly on a Windows 7-based computer|http://support.microsoft.com/kb/975778]

  • CHKDSK fails on fresh install of Windows 7 x64 on mid-2009 MBP with SSD

    There was an earlier post about this that has been archived prematurely that I will reproduce below. The main issue is a flaw in the Windows 7 x64 CHKDSK of the SSD drive in the mid-2009 MBP= 5,2. With fresh OSX installs, bootcamp 3.1, Windows 7 x64 all updates, the CHKDSK operation checks files at about 1 per second in stage 4 of 5, verifying file data.
    Moderators: please leave this open until it is actually resolved.
    Earlier posts:
    Panajev
    Posts: 4
    From: ITALY
    Registered: Oct 14, 2009
    Windows 7 x64, MacBook Pro, frequent CHKDSK after HDD firmware update
    Posted: Nov 2, 2009 6:45 AM
    Hello, I have been having filesystem problems on my Windows 7 partition since the HDD related firmware update (the latest Performance update) was released and installed onto this mid 2009 MacBook Pro.
    The HDD is a 500 GB 7200 RPM model, but it never gave me any troubles under OS X before the "fix" and I know other users had intermittent problems with the HDD on their MacBook Pro's related to the HDD making noises and pausing.
    The fix was released, I installed it and I started seeing my first problem in Windows 7 x64 a few days after... I cleanly shut the OS down, but when I booted it back it asked me to perform a coherency check to the Filesystem... I thought that the problem was related to the fact that I was using the RC1 build of Windows 7... although that problem never manifested itself in the weeks before the Performance Update (HDD firmware fix) was installed and Windows 7 x64 RC1 had been on there and used frequently.
    I recently purchased Windows 7 retail a few days ago and after a bit of trouble-free operation I started having problems again... always shutting the PC down carefully and I was asked to run the CHKDSK utility at boot twice already.
    What to do?
    Message was edited by: Panajev
    MacBook Pro (2009) Mac OS X (10.6.1) Windows 7 x64, Bootcamp 3.0, recent HDD update
    nicegom
    Posts: 6
    Registered: Nov 12, 2009
    Re: Windows 7 x64, MacBook Pro, frequent CHKDSK after HDD firmware update
    Posted: Nov 12, 2009 1:40 AM in response to: Panajev
    Hi there,
    I have a different experience. I installed Windows 7 before the "performance update 1.0" came out. I actually experienced the chkdsk launch problem with Windows 7. I had done repartitioning and clean-install several times but cannot solve the problem. So I tried to install XP and Vista on my MBA (Mid 2009 with SSD) and found that these two OS doesn't introduce such problem.
    To be honest, I'm not sure which caused such problem, Windows 7, a bootcamp driver, or EFI. But I'm sure that CHKDSK in Windows 7 has an obvious bug that needs to be patched (memory leak and maybe this problem as well). So now I'm using Windows Vista SP2. And I'm happy with Vista SP2 (seems to become faster and stable now).
    Cheer,
    Message was edited by: nicegom
    Macbook Air Windows Vista MBA of Mid 2009 with SSD

    Windows 7 x64 all updates
    Just doublechecking. Does that include the recent chkdsk hotfixes?
    [The Chkdsk.exe program does not start correctly on a Windows 7-based computer|http://support.microsoft.com/kb/975778]

  • [Solved]Cannot startx on fresh install with xfce4 and nvidia-304xx-lts

    I just installed Arch base onto my system with my Nvidia GTS 250 Graphics card, however I am unable to start a x session after installing xfce4 and nvidia-304xx-lts followed by the command nvidia-xconfig and reboot.  When I try to issue startxfce4 I get an error pointing to /var/log/Xorg.0.log as follows
    [ 24.856]
    X.Org X Server 1.16.0
    Release Date: 2014-07-16
    [ 24.857] X Protocol Version 11, Revision 0
    [ 24.857] Build Operating System: Linux 3.15.5-2-ARCH x86_64
    [ 24.857] Current Operating System: Linux yte 3.16.2-1-ARCH #1 SMP PREEMPT Sat Sep 6 13:12:51 CEST 2014 x86_64
    [ 24.857] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=/dev/sda5
    [ 24.857] Build Date: 31 July 2014 11:53:19AM
    [ 24.857]
    [ 24.857] Current version of pixman: 0.32.6
    [ 24.858] Before reporting problems, check [url]http://wiki.x.org[/url]
    to make sure that you have the latest version.
    [ 24.858] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    [ 24.858] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Sep 17 21:49:53 2014
    [ 24.875] (==) Using config file: "/etc/X11/xorg.conf"
    [ 24.875] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
    [ 24.897] (==) ServerLayout "Layout0"
    [ 24.897] (**) |-->Screen "Screen0" (0)
    [ 24.897] (**) | |-->Monitor "Monitor0"
    [ 24.905] (**) | |-->Device "Device0"
    [ 24.905] (**) |-->Input Device "Keyboard0"
    [ 24.905] (**) |-->Input Device "Mouse0"
    [ 24.905] (==) Automatically adding devices
    [ 24.905] (==) Automatically enabling devices
    [ 24.905] (==) Automatically adding GPU devices
    [ 24.914] (WW) The directory "/usr/share/fonts/TTF/" does not exist.
    [ 24.914] Entry deleted from font path.
    [ 24.914] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
    [ 24.914] Entry deleted from font path.
    [ 24.914] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
    [ 24.914] Entry deleted from font path.
    [ 24.914] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
    [ 24.914] Entry deleted from font path.
    [ 24.914] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
    [ 24.914] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
    [ 24.914] Entry deleted from font path.
    [ 24.914] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
    [ 24.914] (==) FontPath set to:
    /usr/share/fonts/misc/
    [ 24.914] (==) ModulePath set to "/usr/lib/xorg/modules"
    [ 24.914] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
    [ 24.914] (WW) Disabling Keyboard0
    [ 24.914] (WW) Disabling Mouse0
    [ 24.914] (II) Loader magic: 0x818d80
    [ 24.914] (II) Module ABI versions:
    [ 24.914] X.Org ANSI C Emulation: 0.4
    [ 24.914] X.Org Video Driver: 18.0
    [ 24.914] X.Org XInput driver : 21.0
    [ 24.914] X.Org Server Extension : 8.0
    [ 24.917] (II) systemd-logind: took control of session /org/freedesktop/login1/session/c1
    [ 24.918] (--) PCI:*(0:4:0:0) 10de:0615:19f1:0d76 rev 162, Mem @ 0xfd000000/16777216, 0xd0000000/268435456, 0xfa000000/33554432, I/O @ 0x0000dc00/128, BIOS @ 0x????????/131072
    [ 24.918] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    [ 24.919] (II) LoadModule: "glx"
    [ 24.953] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    [ 25.974] (II) Module glx: vendor="NVIDIA Corporation"
    [ 25.974] compiled for 4.0.2, module version = 1.0.0
    [ 25.974] Module class: X.Org Server Extension
    [ 25.974] (II) NVIDIA GLX Module 304.123 Wed Jul 2 11:19:55 PDT 2014
    [ 25.974] (II) LoadModule: "nvidia"
    [ 25.974] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
    [ 26.027] (II) Module nvidia: vendor="NVIDIA Corporation"
    [ 26.027] compiled for 4.0.2, module version = 1.0.0
    [ 26.027] Module class: X.Org Video Driver
    [ 26.042] (EE) NVIDIA: Failed to load the NVIDIA kernel module. Please check your
    [ 26.042] (EE) NVIDIA: system's kernel log for additional error messages.
    [ 26.042] (II) UnloadModule: "nvidia"
    [ 26.042] (II) Unloading nvidia
    [ 26.042] (EE) Failed to load module "nvidia" (module-specific error, 0)
    [ 26.042] (EE) No drivers available.
    [ 26.042] (EE)
    Fatal server error:
    [ 26.042] (EE) no screens found(EE)
    [ 26.042] (EE)
    Please consult the The X.Org Foundation support
    at [url]http://wiki.x.org[/url]
    for help.
    [ 26.042] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
    [ 26.042] (EE)
    It apears to be trying to load various modules, first of which is my propietary nvidia driver which refers to the kernel log.  My dmesg looks like this:
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.16.2-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.1 (GCC) ) #1 SMP PREEMPT Sat Sep 6 13:12:51 CEST 2014
    [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=/dev/sda5
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ebff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009ec00-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cff9ffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000cffa0000-0x00000000cffadfff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000cffae000-0x00000000cffdffff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000cffe0000-0x00000000cfffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] SMBIOS 2.5 present.
    [ 0.000000] DMI: HP-Pavilion FQ618AA-A2L a6734f/Benicia, BIOS 5.35 12/16/2008
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-DFFFF write-protect
    [ 0.000000] E0000-EFFFF write-through
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0D0000000 mask FF0000000 uncachable
    [ 0.000000] 1 base 0E0000000 mask FE0000000 uncachable
    [ 0.000000] 2 base 000000000 mask F00000000 write-back
    [ 0.000000] 3 base 100000000 mask FE0000000 write-back
    [ 0.000000] 4 base 120000000 mask FF0000000 write-back
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: update [mem 0xd0000000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0xcffa0 max_arch_pfn = 0x400000000
    [ 0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b23000, 0x01b23fff] PGTABLE
    [ 0.000000] BRK [0x01b24000, 0x01b24fff] PGTABLE
    [ 0.000000] BRK [0x01b25000, 0x01b25fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x12fe00000-0x12fffffff]
    [ 0.000000] [mem 0x12fe00000-0x12fffffff] page 2M
    [ 0.000000] BRK [0x01b26000, 0x01b26fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x12c000000-0x12fdfffff]
    [ 0.000000] [mem 0x12c000000-0x12fdfffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x12bffffff]
    [ 0.000000] [mem 0x100000000-0x12bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0xcff9ffff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0xcfdfffff] page 2M
    [ 0.000000] [mem 0xcfe00000-0xcff9ffff] page 4k
    [ 0.000000] RAMDISK: [mem 0x3798e000-0x37cbefff]
    [ 0.000000] ACPI: Early table checksum verification disabled
    [ 0.000000] ACPI: RSDP 0x00000000000FC440 000014 (v00 HPQOEM)
    [ 0.000000] ACPI: RSDT 0x00000000CFFA0000 000044 (v01 HPQOEM SLIC-CPC 20081216 MSFT 00000097)
    [ 0.000000] ACPI: FACP 0x00000000CFFA0200 000084 (v02 HPQOEM SLIC-CPC 20081216 MSFT 00000097)
    [ 0.000000] ACPI: DSDT 0x00000000CFFA0440 004E91 (v01 HPQOEM SLIC-CPC 00000000 INTL 20051117)
    [ 0.000000] ACPI: FACS 0x00000000CFFAE000 000040
    [ 0.000000] ACPI: APIC 0x00000000CFFA0390 00006C (v01 HPQOEM SLIC-CPC 20081216 MSFT 00000097)
    [ 0.000000] ACPI: MCFG 0x00000000CFFA0400 00003C (v01 HPQOEM SLIC-CPC 20081216 MSFT 00000097)
    [ 0.000000] ACPI: OEMB 0x00000000CFFAE040 000072 (v01 HPQOEM SLIC-CPC 20081216 MSFT 00000097)
    [ 0.000000] ACPI: HPET 0x00000000CFFA52E0 000038 (v01 HPQOEM SLIC-CPC 20081216 MSFT 00000097)
    [ 0.000000] ACPI: GSCI 0x00000000CFFAE0C0 002024 (v01 HPQOEM SLIC-CPC 20081216 MSFT 00000097)
    [ 0.000000] ACPI: SLIC 0x00000000CFFB00F0 000176 (v01 HPQOEM SLIC-CPC 00000001 MSFT 00000001)
    [ 0.000000] ACPI: SSDT 0x00000000CFFB14B0 00082F (v01 HPQOEM SLIC-CPC 00000012 INTL 20051117)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000012fffffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x12fffffff]
    [ 0.000000] NODE_DATA [mem 0x12fff7000-0x12fffbfff]
    [ 0.000000] [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff88012b600000-ffff88012f5fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x12fffffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0009dfff]
    [ 0.000000] node 0: [mem 0x00100000-0xcff9ffff]
    [ 0.000000] node 0: [mem 0x100000000-0x12fffffff]
    [ 0.000000] On node 0 totalpages: 1048381
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3997 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 13247 pages used for memmap
    [ 0.000000] DMA32 zone: 847776 pages, LIFO batch:31
    [ 0.000000] Normal zone: 3072 pages used for memmap
    [ 0.000000] Normal zone: 196608 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x808
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e3fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000e4000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcffa0000-0xcffadfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcffae000-0xcffdffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcffe0000-0xcfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xfedfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffefffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfff00000-0xffffffff]
    [ 0.000000] e820: [mem 0xd0000000-0xfedfffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88012fc00000 s86784 r8192 d23808 u524288
    [ 0.000000] pcpu-alloc: s86784 r8192 d23808 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1031977
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=/dev/sda5
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] AGP: Checking aperture...
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 4046408K/4193524K available (5334K kernel code, 887K rwdata, 1688K rodata, 1128K init, 1164K bss, 147116K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
    [ 0.000000] NR_IRQS:8448 nr_irqs:712 16
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 16777216 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration failed
    [ 0.000000] tsc: PIT calibration matches HPET. 1 loops
    [ 0.000000] tsc: Detected 2333.276 MHz processor
    [ 0.006681] Calibrating delay loop (skipped), value calculated using timer frequency.. 4668.99 BogoMIPS (lpj=7777586)
    [ 0.006685] pid_max: default: 32768 minimum: 301
    [ 0.006695] ACPI: Core revision 20140424
    [ 0.012534] ACPI: All ACPI Tables successfully acquired
    [ 0.013368] Security Framework initialized
    [ 0.013377] Yama: becoming mindful.
    [ 0.013731] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.017212] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.017970] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.017980] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.018300] Initializing cgroup subsys memory
    [ 0.018326] Initializing cgroup subsys devices
    [ 0.018334] Initializing cgroup subsys freezer
    [ 0.018338] Initializing cgroup subsys net_cls
    [ 0.018344] Initializing cgroup subsys blkio
    [ 0.018375] CPU: Physical Processor ID: 0
    [ 0.018376] CPU: Processor Core ID: 0
    [ 0.018379] mce: CPU supports 6 MCE banks
    [ 0.018387] CPU0: Thermal monitoring enabled (TM2)
    [ 0.018394] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
    Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
    tlb_flushall_shift: -1
    [ 0.018487] Freeing SMP alternatives memory: 20K (ffffffff819f9000 - ffffffff819fe000)
    [ 0.019569] ftrace: allocating 20434 entries in 80 pages
    [ 0.027196] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.060221] smpboot: CPU0: Intel(R) Core(TM)2 Quad CPU Q8200 @ 2.33GHz (fam: 06, model: 17, stepping: 07)
    [ 0.063333] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
    [ 0.063333] ... version: 2
    [ 0.063333] ... bit width: 40
    [ 0.063333] ... generic registers: 2
    [ 0.063333] ... value mask: 000000ffffffffff
    [ 0.063333] ... max period: 000000007fffffff
    [ 0.063333] ... fixed-purpose events: 3
    [ 0.063333] ... event mask: 0000000700000003
    [ 0.076742] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.083412] x86: Booting SMP configuration:
    [ 0.083415] .... node #0, CPUs: #1 #2 #3
    [ 0.130014] x86: Booted up 1 node, 4 CPUs
    [ 0.130018] smpboot: Total of 4 processors activated (18673.96 BogoMIPS)
    [ 0.133346] devtmpfs: initialized
    [ 0.136924] PM: Registering ACPI NVS region [mem 0xcffae000-0xcffdffff] (204800 bytes)
    [ 0.137923] pinctrl core: initialized pinctrl subsystem
    [ 0.137968] RTC time: 1:49:28, date: 09/18/14
    [ 0.138025] NET: Registered protocol family 16
    [ 0.138158] cpuidle: using governor ladder
    [ 0.138160] cpuidle: using governor menu
    [ 0.138185] ACPI: bus type PCI registered
    [ 0.138187] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.138268] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.138270] PCI: not using MMCONFIG
    [ 0.138272] PCI: Using configuration type 1 for base access
    [ 0.153430] ACPI: Added _OSI(Module Device)
    [ 0.153430] ACPI: Added _OSI(Processor Device)
    [ 0.153430] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.153430] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.155075] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.157331] ACPI: Dynamic OEM Table Load:
    [ 0.157338] ACPI: SSDT 0xFFFF880129AB7600 0001F3 (v01 HPQOEM SLIC-CPC 00000011 INTL 20051117)
    [ 0.157716] ACPI: Dynamic OEM Table Load:
    [ 0.157721] ACPI: SSDT 0xFFFF880129AB7400 0001F3 (v01 HPQOEM SLIC-CPC 00000012 INTL 20051117)
    [ 0.158103] ACPI: Dynamic OEM Table Load:
    [ 0.158109] ACPI: SSDT 0xFFFF8801295D4000 0001F3 (v01 HPQOEM SLIC-CPC 00000012 INTL 20051117)
    [ 0.158489] ACPI: Dynamic OEM Table Load:
    [ 0.158494] ACPI: SSDT 0xFFFF8801295D4200 0001F3 (v01 HPQOEM SLIC-CPC 00000012 INTL 20051117)
    [ 0.158833] ACPI: Interpreter enabled
    [ 0.158843] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
    [ 0.158857] ACPI: (supports S0 S1 S3 S4 S5)
    [ 0.158859] ACPI: Using IOAPIC for interrupt routing
    [ 0.158879] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.159657] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
    [ 0.160132] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.165222] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.165228] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.165233] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
    [ 0.165516] PCI host bridge to bus 0000:00
    [ 0.165519] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.165522] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.165524] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.165526] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.165528] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff]
    [ 0.165530] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xdfffffff]
    [ 0.165532] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xffffffff]
    [ 0.165541] pci 0000:00:00.0: [8086:29c0] type 00 class 0x060000
    [ 0.165640] pci 0000:00:01.0: [8086:29c1] type 01 class 0x060400
    [ 0.165677] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.165716] pci 0000:00:01.0: System wakeup disabled by ACPI
    [ 0.165796] pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300
    [ 0.165844] pci 0000:00:1a.0: reg 0x20: [io 0xb400-0xb41f]
    [ 0.165936] pci 0000:00:1a.0: System wakeup disabled by ACPI
    [ 0.165991] pci 0000:00:1a.1: [8086:2938] type 00 class 0x0c0300
    [ 0.166039] pci 0000:00:1a.1: reg 0x20: [io 0xb480-0xb49f]
    [ 0.166130] pci 0000:00:1a.1: System wakeup disabled by ACPI
    [ 0.166194] pci 0000:00:1a.7: [8086:293c] type 00 class 0x0c0320
    [ 0.166216] pci 0000:00:1a.7: reg 0x10: [mem 0xf9efec00-0xf9efefff]
    [ 0.166307] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    [ 0.166350] pci 0000:00:1a.7: System wakeup disabled by ACPI
    [ 0.166407] pci 0000:00:1b.0: [8086:293e] type 00 class 0x040300
    [ 0.166427] pci 0000:00:1b.0: reg 0x10: [mem 0xf9ef8000-0xf9efbfff 64bit]
    [ 0.166516] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.166616] pci 0000:00:1c.0: [8086:2940] type 01 class 0x060400
    [ 0.166706] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.166752] pci 0000:00:1c.0: System wakeup disabled by ACPI
    [ 0.166807] pci 0000:00:1c.2: [8086:2944] type 01 class 0x060400
    [ 0.166899] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    [ 0.166945] pci 0000:00:1c.2: System wakeup disabled by ACPI
    [ 0.167003] pci 0000:00:1d.0: [8086:2934] type 00 class 0x0c0300
    [ 0.167049] pci 0000:00:1d.0: reg 0x20: [io 0xb800-0xb81f]
    [ 0.167139] pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 0.167203] pci 0000:00:1d.1: [8086:2935] type 00 class 0x0c0300
    [ 0.167250] pci 0000:00:1d.1: reg 0x20: [io 0xb880-0xb89f]
    [ 0.167339] pci 0000:00:1d.1: System wakeup disabled by ACPI
    [ 0.167392] pci 0000:00:1d.2: [8086:2936] type 00 class 0x0c0300
    [ 0.167439] pci 0000:00:1d.2: reg 0x20: [io 0xbc00-0xbc1f]
    [ 0.167528] pci 0000:00:1d.2: System wakeup disabled by ACPI
    [ 0.167580] pci 0000:00:1d.3: [8086:2939] type 00 class 0x0c0300
    [ 0.167627] pci 0000:00:1d.3: reg 0x20: [io 0xc000-0xc01f]
    [ 0.167719] pci 0000:00:1d.3: System wakeup disabled by ACPI
    [ 0.167782] pci 0000:00:1d.7: [8086:293a] type 00 class 0x0c0320
    [ 0.167804] pci 0000:00:1d.7: reg 0x10: [mem 0xf9eff800-0xf9effbff]
    [ 0.167895] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.167938] pci 0000:00:1d.7: System wakeup disabled by ACPI
    [ 0.167989] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
    [ 0.168083] pci 0000:00:1e.0: System wakeup disabled by ACPI
    [ 0.168135] pci 0000:00:1f.0: [8086:2916] type 00 class 0x060100
    [ 0.168209] pci 0000:00:1f.0: can't claim BAR 13 [io 0x0800-0x087f]: address conflict with ACPI CPU throttle [io 0x0810-0x0815]
    [ 0.168214] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO
    [ 0.168217] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff)
    [ 0.168328] pci 0000:00:1f.2: [8086:2922] type 00 class 0x010601
    [ 0.168351] pci 0000:00:1f.2: reg 0x10: [io 0xc880-0xc887]
    [ 0.168361] pci 0000:00:1f.2: reg 0x14: [io 0xc800-0xc803]
    [ 0.168371] pci 0000:00:1f.2: reg 0x18: [io 0xc480-0xc487]
    [ 0.168381] pci 0000:00:1f.2: reg 0x1c: [io 0xc400-0xc403]
    [ 0.168390] pci 0000:00:1f.2: reg 0x20: [io 0xc080-0xc09f]
    [ 0.168400] pci 0000:00:1f.2: reg 0x24: [mem 0xf9eff000-0xf9eff7ff]
    [ 0.168458] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.168549] pci 0000:00:1f.3: [8086:2930] type 00 class 0x0c0500
    [ 0.168567] pci 0000:00:1f.3: reg 0x10: [mem 0xf9effc00-0xf9effcff 64bit]
    [ 0.168592] pci 0000:00:1f.3: reg 0x20: [io 0x0400-0x041f]
    [ 0.168733] pci 0000:04:00.0: [10de:0615] type 00 class 0x030000
    [ 0.168748] pci 0000:04:00.0: reg 0x10: [mem 0xfd000000-0xfdffffff]
    [ 0.168761] pci 0000:04:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.168774] pci 0000:04:00.0: reg 0x1c: [mem 0xfa000000-0xfbffffff 64bit]
    [ 0.168784] pci 0000:04:00.0: reg 0x24: [io 0xdc00-0xdc7f]
    [ 0.168793] pci 0000:04:00.0: reg 0x30: [mem 0xfeae0000-0xfeafffff pref]
    [ 0.168906] pci 0000:00:01.0: PCI bridge to [bus 04]
    [ 0.168909] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
    [ 0.168912] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfeafffff]
    [ 0.168916] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.168982] pci 0000:00:1c.0: PCI bridge to [bus 03]
    [ 0.169127] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000
    [ 0.169187] pci 0000:02:00.0: reg 0x10: [io 0xe800-0xe8ff]
    [ 0.169296] pci 0000:02:00.0: reg 0x18: [mem 0xfebff000-0xfebfffff 64bit]
    [ 0.169354] pci 0000:02:00.0: reg 0x20: [mem 0xf8ff0000-0xf8ffffff 64bit pref]
    [ 0.169397] pci 0000:02:00.0: reg 0x30: [mem 0xfebc0000-0xfebdffff pref]
    [ 0.169663] pci 0000:02:00.0: supports D1 D2
    [ 0.169665] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.169850] pci 0000:00:1c.2: PCI bridge to [bus 02]
    [ 0.169855] pci 0000:00:1c.2: bridge window [io 0xe000-0xefff]
    [ 0.169859] pci 0000:00:1c.2: bridge window [mem 0xfeb00000-0xfebfffff]
    [ 0.169866] pci 0000:00:1c.2: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
    [ 0.169932] pci 0000:01:05.0: [11c1:5811] type 00 class 0x0c0010
    [ 0.169949] pci 0000:01:05.0: reg 0x10: [mem 0xf9fff000-0xf9ffffff]
    [ 0.170025] pci 0000:01:05.0: supports D1 D2
    [ 0.170028] pci 0000:01:05.0: PME# supported from D0 D1 D2 D3hot
    [ 0.170112] pci 0000:00:1e.0: PCI bridge to [bus 01] (subtractive decode)
    [ 0.170119] pci 0000:00:1e.0: bridge window [mem 0xf9f00000-0xf9ffffff]
    [ 0.170126] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.170128] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.170131] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.170133] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
    [ 0.170135] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xdfffffff] (subtractive decode)
    [ 0.170137] pci 0000:00:1e.0: bridge window [mem 0xf0000000-0xffffffff] (subtractive decode)
    [ 0.170715] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    [ 0.170769] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    [ 0.170823] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    [ 0.170875] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
    [ 0.170927] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 5 6 7 10 11 12 14 15)
    [ 0.170983] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    [ 0.171036] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
    [ 0.171088] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 *14 15)
    [ 0.171151] ACPI: Enabled 2 GPEs in block 00 to 3F
    [ 0.171253] vgaarb: device added: PCI:0000:04:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.171253] vgaarb: loaded
    [ 0.171253] vgaarb: bridge control possible 0000:04:00.0
    [ 0.171253] PCI: Using ACPI for IRQ routing
    [ 0.179597] PCI: pci_cache_line_size set to 64 bytes
    [ 0.179658] e820: reserve RAM buffer [mem 0x0009ec00-0x0009ffff]
    [ 0.179660] e820: reserve RAM buffer [mem 0xcffa0000-0xcfffffff]
    [ 0.179795] NetLabel: Initializing
    [ 0.179797] NetLabel: domain hash size = 128
    [ 0.179798] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.179813] NetLabel: unlabeled traffic allowed by default
    [ 0.179835] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
    [ 0.179841] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
    [ 0.179845] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
    [ 0.181019] Switched to clocksource hpet
    [ 0.187008] pnp: PnP ACPI init
    [ 0.187030] ACPI: bus type PNP registered
    [ 0.187128] system 00:00: [mem 0xfed14000-0xfed19fff] has been reserved
    [ 0.187133] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.187213] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.187433] system 00:02: [io 0x04d0-0x04d1] has been reserved
    [ 0.187436] system 00:02: [io 0x0800-0x087f] could not be reserved
    [ 0.187438] system 00:02: [io 0x0480-0x04bf] has been reserved
    [ 0.187441] system 00:02: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.187444] system 00:02: [mem 0xfed20000-0xfed8ffff] has been reserved
    [ 0.187447] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.187548] system 00:03: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.187551] system 00:03: [mem 0xfee00000-0xfee00fff] has been reserved
    [ 0.187555] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.187674] system 00:04: [io 0x0a00-0x0adf] has been reserved
    [ 0.187678] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.187756] system 00:05: [mem 0xffc00000-0xffefffff] has been reserved
    [ 0.187759] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.187825] system 00:06: [mem 0xe0000000-0xefffffff] has been reserved
    [ 0.187829] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.188006] system 00:07: [mem 0x00000000-0x0009ffff] could not be reserved
    [ 0.188009] system 00:07: [mem 0x000c0000-0x000cffff] could not be reserved
    [ 0.188012] system 00:07: [mem 0x000e0000-0x000fffff] could not be reserved
    [ 0.188014] system 00:07: [mem 0x00100000-0xcfffffff] could not be reserved
    [ 0.188017] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.188133] pnp: PnP ACPI: found 8 devices
    [ 0.188135] ACPI: bus type PNP unregistered
    [ 0.197465] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 03] add_size 1000
    [ 0.197469] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000
    [ 0.197472] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 03] add_size 200000
    [ 0.197491] pci 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
    [ 0.197494] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
    [ 0.197497] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.197499] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.197505] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf0000000-0xf01fffff]
    [ 0.197510] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf0200000-0xf03fffff 64bit pref]
    [ 0.197514] pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
    [ 0.197516] pci 0000:00:01.0: PCI bridge to [bus 04]
    [ 0.197519] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
    [ 0.197522] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfeafffff]
    [ 0.197525] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.197529] pci 0000:00:1c.0: PCI bridge to [bus 03]
    [ 0.197532] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
    [ 0.197537] pci 0000:00:1c.0: bridge window [mem 0xf0000000-0xf01fffff]
    [ 0.197542] pci 0000:00:1c.0: bridge window [mem 0xf0200000-0xf03fffff 64bit pref]
    [ 0.197548] pci 0000:00:1c.2: PCI bridge to [bus 02]
    [ 0.197551] pci 0000:00:1c.2: bridge window [io 0xe000-0xefff]
    [ 0.197557] pci 0000:00:1c.2: bridge window [mem 0xfeb00000-0xfebfffff]
    [ 0.197561] pci 0000:00:1c.2: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
    [ 0.197568] pci 0000:00:1e.0: PCI bridge to [bus 01]
    [ 0.197573] pci 0000:00:1e.0: bridge window [mem 0xf9f00000-0xf9ffffff]
    [ 0.197582] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.197585] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.197587] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.197589] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
    [ 0.197591] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xdfffffff]
    [ 0.197593] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xffffffff]
    [ 0.197596] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
    [ 0.197598] pci_bus 0000:04: resource 1 [mem 0xfa000000-0xfeafffff]
    [ 0.197600] pci_bus 0000:04: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.197602] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
    [ 0.197604] pci_bus 0000:03: resource 1 [mem 0xf0000000-0xf01fffff]
    [ 0.197607] pci_bus 0000:03: resource 2 [mem 0xf0200000-0xf03fffff 64bit pref]
    [ 0.197609] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
    [ 0.197611] pci_bus 0000:02: resource 1 [mem 0xfeb00000-0xfebfffff]
    [ 0.197613] pci_bus 0000:02: resource 2 [mem 0xf8f00000-0xf8ffffff 64bit pref]
    [ 0.197615] pci_bus 0000:01: resource 1 [mem 0xf9f00000-0xf9ffffff]
    [ 0.197618] pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
    [ 0.197620] pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
    [ 0.197622] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.197624] pci_bus 0000:01: resource 7 [mem 0x000d0000-0x000dffff]
    [ 0.197626] pci_bus 0000:01: resource 8 [mem 0xd0000000-0xdfffffff]
    [ 0.197628] pci_bus 0000:01: resource 9 [mem 0xf0000000-0xffffffff]
    [ 0.197657] NET: Registered protocol family 2
    [ 0.197878] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
    [ 0.197999] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
    [ 0.198159] TCP: Hash tables configured (established 32768 bind 32768)
    [ 0.198193] TCP: reno registered
    [ 0.198203] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.198230] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.198298] NET: Registered protocol family 1
    [ 0.199202] pci 0000:04:00.0: Boot video device
    [ 0.199211] PCI: CLS 32 bytes, default 64
    [ 0.199266] Unpacking initramfs...
    [ 0.265035] Freeing initrd memory: 3268K (ffff88003798e000 - ffff880037cbf000)
    [ 0.265050] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 0.265053] software IO TLB [mem 0xcbfa0000-0xcffa0000] (64MB) mapped at [ffff8800cbfa0000-ffff8800cff9ffff]
    [ 0.265383] Scanning for low memory corruption every 60 seconds
    [ 0.265750] futex hash table entries: 1024 (order: 4, 65536 bytes)
    [ 0.266220] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.268226] zbud: loaded
    [ 0.268426] VFS: Disk quotas dquot_6.5.2
    [ 0.268472] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.268644] msgmni has been set to 7909
    [ 0.268709] Key type big_key registered
    [ 0.269063] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.269162] io scheduler noop registered
    [ 0.269165] io scheduler deadline registered
    [ 0.269227] io scheduler cfq registered (default)
    [ 0.269402] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
    [ 0.269456] pcieport 0000:00:1c.0: enabling device (0104 -> 0107)
    [ 0.269523] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
    [ 0.269664] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
    [ 0.269772] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.269794] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.269839] intel_idle: does not run on family 6 model 23
    [ 0.269876] GHES: HEST is not enabled!
    [ 0.269980] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.270599] Linux agpgart interface v0.103
    [ 0.270658] rtc_cmos 00:01: RTC can wake from S4
    [ 0.270820] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
    [ 0.270850] rtc_cmos 00:01: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    [ 0.270864] ledtrig-cpu: registered to indicate activity on CPUs
    [ 0.270984] TCP: cubic registered
    [ 0.271114] NET: Registered protocol family 10
    [ 0.271372] NET: Registered protocol family 17
    [ 0.271821] registered taskstats version 1
    [ 0.272365] Magic number: 14:261:812
    [ 0.272465] rtc_cmos 00:01: setting system clock to 2014-09-18 01:49:28 UTC (1411004968)
    [ 0.272539] PM: Hibernation image not present or could not be loaded.
    [ 0.273767] Freeing unused kernel memory: 1128K (ffffffff818df000 - ffffffff819f9000)
    [ 0.273769] Write protecting the kernel read-only data: 8192k
    [ 0.276140] Freeing unused kernel memory: 800K (ffff880001538000 - ffff880001600000)
    [ 0.277248] Freeing unused kernel memory: 360K (ffff8800017a6000 - ffff880001800000)
    [ 0.284774] random: systemd-tmpfile urandom read with 1 bits of entropy available
    [ 0.286420] systemd-udevd[59]: starting version 216
    [ 0.299539] i8042: PNP: No PS/2 controller found. Probing ports directly.
    [ 0.302475] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.302536] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.305975] ACPI: bus type USB registered
    [ 0.306007] usbcore: registered new interface driver usbfs
    [ 0.306020] usbcore: registered new interface driver hub
    [ 0.306135] usbcore: registered new device driver usb
    [ 0.306716] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.307076] ehci-pci: EHCI PCI platform driver
    [ 0.307191] uhci_hcd: USB Universal Host Controller Interface driver
    [ 0.307253] ehci-pci 0000:00:1a.7: EHCI Host Controller
    [ 0.307261] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
    [ 0.307274] ehci-pci 0000:00:1a.7: debug port 1
    [ 0.311183] ehci-pci 0000:00:1a.7: cache line size of 32 is not supported
    [ 0.311202] ehci-pci 0000:00:1a.7: irq 18, io mem 0xf9efec00
    [ 0.315748] SCSI subsystem initialized
    [ 0.317397] libata version 3.00 loaded.
    [ 0.320025] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    [ 0.323598] hub 1-0:1.0: USB hub found
    [ 0.323608] hub 1-0:1.0: 4 ports detected
    [ 0.323904] ehci-pci 0000:00:1d.7: EHCI Host Controller
    [ 0.323911] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
    [ 0.323925] ehci-pci 0000:00:1d.7: debug port 1
    [ 0.327815] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
    [ 0.327834] ehci-pci 0000:00:1d.7: irq 23, io mem 0xf9eff800
    [ 0.336696] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 0.336926] hub 2-0:1.0: USB hub found
    [ 0.336936] hub 2-0:1.0: 8 ports detected
    [ 0.337334] uhci_hcd 0000:00:1a.0: UHCI Host Controller
    [ 0.337345] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    [ 0.337354] uhci_hcd 0000:00:1a.0: detected 2 ports
    [ 0.337394] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b400
    [ 0.337866] hub 3-0:1.0: USB hub found
    [ 0.337875] hub 3-0:1.0: 2 ports detected
    [ 0.338094] uhci_hcd 0000:00:1a.1: UHCI Host Controller
    [ 0.338100] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
    [ 0.338107] uhci_hcd 0000:00:1a.1: detected 2 ports
    [ 0.338134] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b480
    [ 0.338347] hub 4-0:1.0: USB hub found
    [ 0.338355] hub 4-0:1.0: 2 ports detected
    [ 0.338546] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 0.338553] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
    [ 0.338559] uhci_hcd 0000:00:1d.0: detected 2 ports
    [ 0.338578] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b800
    [ 0.338786] hub 5-0:1.0: USB hub found
    [ 0.338794] hub 5-0:1.0: 2 ports detected
    [ 0.338981] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 0.338987] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
    [ 0.338993] uhci_hcd 0000:00:1d.1: detected 2 ports
    [ 0.339020] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b880
    [ 0.339235] hub 6-0:1.0: USB hub found
    [ 0.339244] hub 6-0:1.0: 2 ports detected
    [ 0.339429] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 0.339435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
    [ 0.339442] uhci_hcd 0000:00:1d.2: detected 2 ports
    [ 0.339460] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bc00
    [ 0.339667] hub 7-0:1.0: USB hub found
    [ 0.339675] hub 7-0:1.0: 2 ports detected
    [ 0.339862] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [ 0.339870] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 8
    [ 0.339876] uhci_hcd 0000:00:1d.3: detected 2 ports
    [ 0.339894] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000c000
    [ 0.340109] hub 8-0:1.0: USB hub found
    [ 0.340117] hub 8-0:1.0: 2 ports detected
    [ 0.340263] ahci 0000:00:1f.2: version 3.0
    [ 0.340410] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
    [ 0.340467] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
    [ 0.340515] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
    [ 0.340519] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs
    [ 0.366734] firewire_ohci 0000:01:05.0: added OHCI v1.0 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
    [ 0.374399] scsi0 : ahci
    [ 0.374615] scsi1 : ahci
    [ 0.374814] scsi2 : ahci
    [ 0.375005] scsi3 : ahci
    [ 0.375196] scsi4 : ahci
    [ 0.375388] scsi5 : ahci
    [ 0.375468] ata1: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff100 irq 43
    [ 0.375472] ata2: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff180 irq 43
    [ 0.375474] ata3: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff200 irq 43
    [ 0.375477] ata4: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff280 irq 43
    [ 0.375480] ata5: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff300 irq 43
    [ 0.375482] ata6: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff380 irq 43
    [ 0.630034] usb 1-2: new high-speed USB device number 2 using ehci-pci
    [ 0.693360] ata1: SATA link down (SStatus 0 SControl 300)
    [ 0.754296] hub 1-2:1.0: USB hub found
    [ 0.754373] hub 1-2:1.0: 7 ports detected
    [ 0.866772] firewire_core 0000:01:05.0: created device fw0: GUID 001e8c0001bb0f0a, S400
    [ 1.013360] ata2: SATA link down (SStatus 0 SControl 300)
    [ 1.266684] tsc: Refined TSC clocksource calibration: 2333.285 MHz
    [ 1.333363] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 1.336819] ata3.00: ATA-8: WDC WD10EARS-00MVWB0, 50.0AB50, max UDMA/133
    [ 1.336823] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
    [ 1.340399] ata3.00: configured for UDMA/133
    [ 1.340517] scsi 2:0:0:0: Direct-Access ATA WDC WD10EARS-00M AB50 PQ: 0 ANSI: 5
    [ 1.373365] usb 2-5: new high-speed USB device number 3 using ehci-pci
    [ 1.500038] usb-storage 2-5:1.0: USB Mass Storage device detected
    [ 1.500227] scsi6 : usb-storage 2-5:1.0
    [ 1.500322] usbcore: registered new interface driver usb-storage
    [ 1.500694] usbcore: registered new interface driver uas
    [ 1.660027] ata4: SATA link down (SStatus 0 SControl 300)
    [ 1.980028] usb 5-1: new full-speed USB device number 2 using uhci_hcd
    [ 1.980030] ata5: SATA link down (SStatus 0 SControl 300)
    [ 2.125620] usb 5-1: config 1 has an invalid descriptor of length 17, skipping remainder of the config
    [ 2.125624] usb 5-1: config 1 has 1 interface, different from the descriptor's value: 4
    [ 2.125628] usb 5-1: config 1 interface 0 altsetting 0 has 0 endpoint descriptors, different from the interface descriptor's value: 2
    [ 2.266750] Switched to clocksource tsc
    [ 2.370018] usb 4-1: new full-speed USB device number 2 using uhci_hcd
    [ 2.504151] scsi 6:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
    [ 2.504778] scsi 6:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
    [ 2.505402] scsi 6:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
    [ 2.506038] scsi 6:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
    [ 2.509294] sd 2:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    [ 2.509340] sd 2:0:0:0: [sda] Write Protect is off
    [ 2.509343] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.509363] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.515260] sd 6:0:0:0: [sdb] Attached SCSI removable disk
    [ 2.515889] sd 6:0:0:1: [sdc] Attached SCSI removable disk
    [ 2.516511] sd 6:0:0:2: [sdd] Attached SCSI removable disk
    [ 2.517136] sd 6:0:0:3: [sde] Attached SCSI removable disk
    [ 2.569106] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
    [ 2.569597] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 2.571450] hidraw: raw HID events driver (C) Jiri Kosina
    [ 2.586591] usbcore: registered new interface driver usbhid
    [ 2.586594] usbhid: USB HID core driver
    [ 2.587316] input: Logitech Gaming Mouse G600 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/0003:046D:C24A.0001/input/input2
    [ 2.587394] hid-generic 0003:046D:C24A.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech Gaming Mouse G600] on usb-0000:00:1a.1-1/input0
    [ 2.620024] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 2.621301] input: Logitech Gaming Mouse G600 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.1/0003:046D:C24A.0002/input/input3
    [ 2.621413] hid-generic 0003:046D:C24A.0002: input,hiddev0,hidraw1: USB HID v1.11 Keyboard [Logitech Gaming Mouse G600] on usb-0000:00:1a.1-1/input1
    [ 2.623705] ata6.00: ATAPI: HL-DT-ST BDDVDRW GBC-H20L, 1.B8, max UDMA/100
    [ 2.628682] ata6.00: configured for UDMA/100
    [ 2.741224] scsi 5:0:0:0: CD-ROM HL-DT-ST BDDVDRW GBC-H20L 1.B8 PQ: 0 ANSI: 5
    [ 2.796696] usb 8-2: new full-speed USB device number 2 using uhci_hcd
    [ 2.870295] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 2.870300] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.870508] sr 5:0:0:0: Attached scsi CD-ROM sr0
    [ 2.983435] input: Logitech Logitech Illuminated Keyboard as /devices/pci0000:00/0000:00:1d.3/usb8/8-2/8-2:1.0/0003:046D:C318.0003/input/input4
    [ 2.983518] hid-generic 0003:046D:C318.0003: input,hidraw2: USB HID v1.11 Keyboard [Logitech Logitech Illuminated Keyboard] on usb-0000:00:1d.3-2/input0
    [ 2.987055] input: Logitech Logitech Illuminated Keyboard as /devices/pci0000:00/0000:00:1d.3/usb8/8-2/8-2:1.1/0003:046D:C318.0004/input/input5
    [ 2.987190] hid-generic 0003:046D:C318.0004: input,hiddev0,hidraw3: USB HID v1.11 Device [Logitech Logitech Illuminated Keyboard] on usb-0000:00:1d.3-2/input1
    [ 3.173499] usb 1-2.7: new high-speed USB device number 4 using ehci-pci
    [ 3.257551] hub 1-2.7:1.0: USB hub found
    [ 3.257622] hub 1-2.7:1.0: 4 ports detected
    [ 3.316702] floppy0: no floppy controllers found
    [ 3.830625] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
    [ 4.027733] random: nonblocking pool is initialized
    [ 4.403265] systemd[1]: systemd 216 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD -IDN )
    [ 4.403452] systemd[1]: Detected architecture 'x86-64'.
    [ 4.434571] systemd[1]: Set hostname to <yte>.
    [ 5.263934] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 5.264264] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 5.264322] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 5.264334] systemd[1]: Starting Remote File Systems.
    [ 5.264630] systemd[1]: Reached target Remote File Systems.
    [ 5.264663] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
    [ 5.265007] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
    [ 5.265025] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
    [ 5.265058] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [ 5.265067] systemd[1]: Starting Paths.
    [ 5.265331] systemd[1]: Reached target Paths.
    [ 5.265342] systemd[1]: Starting Encrypted Volumes.
    [ 5.265614] systemd[1]: Reached target Encrypted Volumes.
    [ 5.265625] systemd[1]: Expecting device dev-sda3.device...
    [ 5.265819] systemd[1]: Expecting device dev-sda6.device...
    [ 5.266013] systemd[1]: Starting Root Slice.
    [ 5.275815] systemd[1]: Created slice Root Slice.
    [ 5.275829] systemd[1]: Starting User and Session Slice.
    [ 5.276279] systemd[1]: Created slice User and Session Slice.
    [ 5.276291] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 5.276593] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 5.276604] systemd[1]: Starting Delayed Shutdown Socket.
    [ 5.276899] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 5.276910] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 5.277203] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 5.277213] systemd[1]: Starting Journal Socket (/dev/log).
    [ 5.277507] systemd[1]: Listening on Journal Socket (/dev/log).
    [ 5.277518] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 5.277808] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 5.277824] systemd[1]: Starting udev Kernel Socket.
    [ 5.278109] systemd[1]: Listening on udev Kernel Socket.
    [ 5.278123] systemd[1]: Starting udev Control Socket.
    [ 5.278410] systemd[1]: Listening on udev Control Socket.
    [ 5.278424] systemd[1]: Starting Journal Socket.
    [ 5.278716] systemd[1]: Listening on Journal Socket.
    [ 5.278736] systemd[1]: Starting System Slice.
    [ 5.279185] systemd[1]: Created slice System Slice.
    [ 5.279201] systemd[1]: Starting File System Check on Root Device...
    [ 5.279858] systemd[1]: Starting system-systemd\x2dfsck.slice.
    [ 5.280411] systemd[1]: Created slice system-systemd\x2dfsck.slice.
    [ 5.371945] systemd[1]: Mounting Temporary Directory...
    [ 5.379927] systemd[1]: Starting system-getty.slice.
    [ 5.380442] systemd[1]: Created slice system-getty.slice.
    [ 5.414498] systemd[1]: Starting Create list of required static device nodes for the current kernel...
    [ 5.477478] systemd[1]: Started Set Up Additional Binary Formats.
    [ 5.477515] systemd[1]: Mounting POSIX Message Queue File System...
    [ 5.503309] systemd[1]: Started Load Kernel Modules.
    [ 5.503363] systemd[1]: Starting Apply Kernel Variables...
    [ 5.504202] systemd[1]: Mounting Configuration File System...
    [ 5.504898] systemd[1]: Mounted FUSE Control File System.
    [ 5.504935] systemd[1]: Mounting Huge Pages File System...
    [ 5.505656] systemd[1]: Mounting Debug File System...
    [ 5.506353] systemd[1]: Starting Setup Virtual Console...
    [ 5.507155] systemd[1]: Starting udev Coldplug all Devices...
    [ 5.507863] systemd[1]: Starting Journal Service...
    [ 5.508912] systemd[1]: Started Journal Service.
    [ 5.600542] EXT4-fs (sda5): re-mounted. Opts: data=ordered
    [ 5.836201] systemd-udevd[175]: starting version 216
    [ 6.237023] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
    [ 6.237029] ACPI: Power Button [PWRB]
    [ 6.237089] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
    [ 6.237092] ACPI: Power Button [PWRF]
    [ 6.393110] ACPI Warning: SystemIO range 0x0000000000000828-0x000000000000082f conflicts with OpRegion 0x0000000000000800-0x000000000000084f (\PMRG) (20140424/utaddress-258)
    [ 6.393118] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 6.393146] lpc_ich: Resource conflict(s) found affecting gpio_ich
    [ 6.403316] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 6.624551] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
    [ 6.697197] sound hdaudioC0D0: ALC1200: SKU not ready 0x411111f0
    [ 6.697713] sound hdaudioC0D0: autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
    [ 6.697715] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
    [ 6.697718] sound hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
    [ 6.697720] sound hdaudioC0D0: mono: mono_out=0x0
    [ 6.697722] sound hdaudioC0D0: dig-out=0x11/0x1e
    [ 6.697724] sound hdaudioC0D0: inputs:
    [ 6.697726] sound hdaudioC0D0: Front Mic=0x19
    [ 6.697729] sound hdaudioC0D0: Rear Mic=0x18
    [ 6.697731] sound hdaudioC0D0: Line=0x1c
    [ 6.697732] sound hdaudioC0D0: dig-in=0x1f
    [ 6.702189] input: PC Speaker as /devices/platform/pcspkr/input/input9
    [ 6.709310] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
    [ 6.717944] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input8
    [ 6.718325] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
    [ 6.718367] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
    [ 6.718409] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
    [ 6.718451] input: HDA Intel Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
    [ 6.718493] input: HDA Intel Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
    [ 6.718576] input: HDA Intel Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
    [ 6.718699] input: HDA Intel Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
    [ 6.718743] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
    [ 6.728756] microcode: CPU0 sig=0x10677, pf=0x10, revision=0x705
    [ 6.780564] gpio_ich: GPIO from 195 to 255 on gpio_ich
    [ 6.802218] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
    [ 6.802227] r8169 0000:02:00.0: can't disable ASPM; OS doesn't have ASPM control
    [ 6.802531] r8169 0000:02:00.0: irq 45 for MSI/MSI-X
    [ 6.802745] r8169 0000:02:00.0 eth0: RTL8168c/8111c at 0xffffc90010736000, 00:24:8c:13:67:78, XID 1c4000c0 IRQ 45
    [ 6.802748] r8169 0000:02:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
    [ 6.815163] microcode: CPU1 sig=0x10677, pf=0x10, revision=0x705
    [ 6.815200] microcode: CPU2 sig=0x10677, pf=0x10, revision=0x705
    [ 6.815216] microcode: CPU3 sig=0x10677, pf=0x10, revision=0x705
    [ 6.815650] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 6.852178] iTCO_vendor_support: vendor-support=0
    [ 6.951618] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
    [ 6.951664] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0860)
    [ 6.952163] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 6.961276] systemd-udevd[183]: renamed network interface eth0 to enp2s0
    [ 6.962065] mousedev: PS/2 mouse device common for all mice
    [ 7.539521] Adding 4051964k swap on /dev/sda3. Priority:-1 extents:1 across:4051964k FS
    [ 8.405763] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 8.687024] systemd-journald[157]: Received request to flush runtime journal from PID 1
    [ 9.356701] floppy0: no floppy controllers found
    [ 10.274611] r8169 0000:02:00.0 enp2s0: link down
    [ 10.274665] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
    [ 11.871962] r8169 0000:02:00.0 enp2s0: link up
    [ 11.871971] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready
    Due to the length of the above logs I looked for a option to upload them but could not find the button for this, my appologies.  Would anyone be able to see where I am going wrong?
    Last edited by meschael (2014-09-18 04:16:08)

    The first code block contains my Xorg.0.log however I just tryed modprove nvidia and recieved FATAL: Module nvidia not found. which I discovered was solved by someone here https://bbs.archlinux.org/viewtopic.php?pid=961852 however when I tryed to do a pacman -S nvidia nvidia-utils I get a unresolved confilict with nvidia-304xx-utils which after trying to remove with pacman -Rs shows dependencies with cario, Im not sure how far back I should start removing things to solve this conflict or how to go abouts solving it
    +++++++++
    Update: Solved
    +++++++++
    I did some more looking and found I could force the uninstall of nvidia-304xx-lts with pacman -Rdds nvidia-304xx-lts and after revisiting the Nvidia page on the wiki for the dozenth time I started thinking maybe I needed nvidia-304xx oposed to the lts release as google as kindly pointed out lts is long term support and maybe my kernel was not lts and thus conflicting.  This turned out to be the case, after removing the ofending lts version of the driver, replacing with the correct nvidia-304xx , another nvidia-xconfig and reboot followed by modprobe nvida and startxfce4 my wounderfull xfce is now running as I type this messsage in firefox.  Thank you for you help, as you asking about the modprobe output caused the chain of events leading to the success.
    Last edited by meschael (2014-09-18 04:15:30)

  • [SOLVED]Grub fails to open dm-crypt+LUKS volume on boot(Waiting 10s..)

    I know there are quite a few solved posts like these but it's usually because of "mkinitcpio -p linux" not being regenerated.
    My problem is after boot Grub says:
    running hook [udev]
    running hook [encrypt]
    Waiting 10 seconds for device /dev/disk/by-uuid/d1d0825c-25d1-4cbe-811f-725d9ef8d034>...
    ERROR: device 'UUID=d1d0825c-25d1-4cbe-811f-725d9ef8d034' not found. Skipping fsck.
    ERROR: Unable to find root device 'UUID=d1d0825c-25d1-4cbe-811f-725d9ef8d034'.
    Here are all the files that I think would be needed for this:
    /etc/fstab
    # /etc/fstab: static file system information
    # <file system> <dir> <type> <options> <dump> <pass>
    #/dev/mapper/cryptroot / ext4 rw,realtime,data=ordered 0 1
    UUID=d1d0825c-25d1-4cbe-811f-725d9ef8d034 / ext4 rw,relatime,data=ordered 0 1
    #/dev/sda5 /boot ext4 rw,relatime,data=ordered 0 2
    UUID=d04b37b1-4dfb-451c-b582-b9d95ca8fe22 /boot ext4 rw,relatime,data=ordered 0 2
    lsblk
    NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
    sda 8:0 0 298.1G 0 disk
    ├─sda1 8:1 0 100M 0 part
    ├─sda2 8:2 0 97.6G 0 part
    ├─sda3 8:3 0 1K 0 part
    ├─sda5 8:5 0 300M 0 part
    ├─sda6 8:6 0 50G 0 part
    │ └─cryptroot 254:1 0 50G 0 crypt /
    ├─sda7 8:7 0 1G 0 part
    └─sda8 8:8 0 149.1G 0 part
    sdb 8:16 1 29.3G 0 disk
    ├─sdb1 8:17 1 558M 0 part
    └─sdb2 8:18 1 31M 0 part
    sdc 8:32 1 15G 0 disk
    └─sdc1 8:33 1 15G 0 part /mnt/usb
    sr0 11:0 1 1024M 0 rom
    loop0 7:0 0 240.9M 1 loop
    loop1 7:1 0 1.5G 1 loop
    └─arch_root-image 254:0 0 1.5G 0 dm /etc/resolv.conf
    loop2 7:2 0 1.5G 0 loop
    └─arch_root-image 254:0 0 1.5G 0 dm /etc/resolv.conf
    blkid
    /dev/sda1: LABEL="System Reserved" UUID="3A481C2D481BE703" TYPE="ntfs" PARTUUID="850a6169-01"
    /dev/sda2: UUID="EE3443C234438D11" TYPE="ntfs" PARTUUID="850a6169-02"
    /dev/sda5: UUID="d04b37b1-4dfb-451c-b582-b9d95ca8fe22" TYPE="ext4" PARTUUID="850a6169-05"
    /dev/sda6: UUID="691c218e-658f-47ff-8296-6b266b2c06c9" TYPE="crypto_LUKS" PARTUUID="850a6169-06"
    /dev/sdb1: UUID="2014-07-03-18-41-56-00" LABEL="ARCH_201407" TYPE="iso9660" PTUUID="6039e1c4" PTTYPE="dos" PARTUUID="6039e1c4-01"
    /dev/sdb2: SEC_TYPE="msdos" LABEL="ARCHISO_EFI" UUID="3B47-A69A" TYPE="vfat" PARTUUID="6039e1c4-02"
    /dev/loop0: TYPE="squashfs"
    /dev/loop1: UUID="5857fcdc-02d9-4d16-aeb5-00d786995ffc" TYPE="ext4"
    /dev/loop2: UUID="5857fcdc-02d9-4d16-aeb5-00d786995ffc" TYPE="ext4"
    /dev/mapper/arch_root-image: UUID="5857fcdc-02d9-4d16-aeb5-00d786995ffc" TYPE="ext4"
    /dev/mapper/cryptroot: UUID="d1d0825c-25d1-4cbe-811f-725d9ef8d034" TYPE="ext4"
    /dev/sdc1: UUID="86D3-3C7E" TYPE="vfat" PARTUUID="c3072e18-01"
    /dev/sda7: PARTUUID="850a6169-07"
    /dev/sda8: PARTUUID="850a6169-08"
    /etc/default/grub
    GRUB_DEFAULT=0
    GRUB_TIMEOUT=5
    GRUB_DISTRIBUTOR="Arch"
    GRUB_CMDLINE_LINUX_DEFAULT="quiet"
    GRUB_CMDLINE_LINUX="cryptdevice=/dev/sda6:cryptroot"
    # Preload both GPT and MBR modules so that they are not missed
    GRUB_PRELOAD_MODULES="part_gpt part_msdos"
    # Uncomment to enable Hidden Menu, and optionally hide the timeout count
    #GRUB_HIDDEN_TIMEOUT=5
    #GRUB_HIDDEN_TIMEOUT_QUIET=true
    # Uncomment to use basic console
    GRUB_TERMINAL_INPUT=console
    # Uncomment to disable graphical terminal
    #GRUB_TERMINAL_OUTPUT=console
    # The resolution used on graphical terminal
    # note that you can use only modes which your graphic card supports via VBE
    # you can see them in real GRUB with the command `vbeinfo'
    GRUB_GFXMODE=auto
    # Uncomment to allow the kernel use the same resolution used by grub
    GRUB_GFXPAYLOAD_LINUX=keep
    # Uncomment if you want GRUB to pass to the Linux kernel the old parameter
    # format "root=/dev/xxx" instead of "root=/dev/disk/by-uuid/xxx"
    #GRUB_DISABLE_LINUX_UUID=true
    # Uncomment to disable generation of recovery mode menu entries
    GRUB_DISABLE_RECOVERY=true
    # Uncomment and set to the desired menu colors. Used by normal and wallpaper
    # modes only. Entries specified as foreground/background.
    #GRUB_COLOR_NORMAL="light-blue/black"
    #GRUB_COLOR_HIGHLIGHT="light-cyan/blue"
    # Uncomment one of them for the gfx desired, a image background or a gfxtheme
    #GRUB_BACKGROUND="/path/to/wallpaper"
    #GRUB_THEME="/path/to/gfxtheme"
    # Uncomment to get a beep at GRUB start
    #GRUB_INIT_TUNE="480 440 1"
    #GRUB_SAVEDEFAULT="true"
    /boot/grub/grub.cfg
    # DO NOT EDIT THIS FILE
    # It is automatically generated by grub-mkconfig using templates
    # from /etc/grub.d and settings from /etc/default/grub
    ### BEGIN /etc/grub.d/00_header ###
    insmod part_gpt
    insmod part_msdos
    if [ -s $prefix/grubenv ]; then
    load_env
    fi
    if [ "${next_entry}" ] ; then
    set default="${next_entry}"
    set next_entry=
    save_env next_entry
    set boot_once=true
    else
    set default="0"
    fi
    if [ x"${feature_menuentry_id}" = xy ]; then
    menuentry_id_option="--id"
    else
    menuentry_id_option=""
    fi
    export menuentry_id_option
    if [ "${prev_saved_entry}" ]; then
    set saved_entry="${prev_saved_entry}"
    save_env saved_entry
    set prev_saved_entry=
    save_env prev_saved_entry
    set boot_once=true
    fi
    function savedefault {
    if [ -z "${boot_once}" ]; then
    saved_entry="${chosen}"
    save_env saved_entry
    fi
    function load_video {
    if [ x$feature_all_video_module = xy ]; then
    insmod all_video
    else
    insmod efi_gop
    insmod efi_uga
    insmod ieee1275_fb
    insmod vbe
    insmod vga
    insmod video_bochs
    insmod video_cirrus
    fi
    if loadfont unicode ; then
    set gfxmode=auto
    load_video
    insmod gfxterm
    set locale_dir=$prefix/locale
    set lang=en_US
    insmod gettext
    fi
    terminal_input console
    terminal_output gfxterm
    if [ x$feature_timeout_style = xy ] ; then
    set timeout_style=menu
    set timeout=5
    # Fallback normal timeout code in case the timeout_style feature is
    # unavailable.
    else
    set timeout=5
    fi
    ### END /etc/grub.d/00_header ###
    ### BEGIN /etc/grub.d/10_linux ###
    menuentry 'Arch Linux' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-d1d0825c-25d1-4cbe-811f-725d9ef8d034' {
    load_video
    set gfxpayload=keep
    insmod gzio
    insmod part_msdos
    insmod cryptodisk luks gcry_rijndael gcry_rijndael gcry_sha1
    insmod ext2
    set root='cryptouuid/691c218e658f47ff82966b266b2c06c9'
    if [ x$feature_platform_search_hint = xy ]; then
    search --no-floppy --fs-uuid --set=root --hint='cryptouuid/691c218e658f47ff82966b266b2c06c9' d1d0825c-25d1-4cbe-811f-725d9ef8d034
    else
    search --no-floppy --fs-uuid --set=root d1d0825c-25d1-4cbe-811f-725d9ef8d034
    fi
    echo 'Loading Linux linux ...'
    linux /boot/vmlinuz-linux root=UUID=d1d0825c-25d1-4cbe-811f-725d9ef8d034 rw cryptdevice=/dev/sda6:cryptroot quiet
    echo 'Loading initial ramdisk ...'
    initrd /boot/initramfs-linux.img
    submenu 'Advanced options for Arch Linux' $menuentry_id_option 'gnulinux-advanced-d1d0825c-25d1-4cbe-811f-725d9ef8d034' {
    menuentry 'Arch Linux, with Linux linux' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-linux-advanced-d1d0825c-25d1-4cbe-811f-725d9ef8d034' {
    load_video
    set gfxpayload=keep
    insmod gzio
    insmod part_msdos
    insmod cryptodisk luks gcry_rijndael gcry_rijndael gcry_sha1
    insmod ext2
    set root='cryptouuid/691c218e658f47ff82966b266b2c06c9'
    if [ x$feature_platform_search_hint = xy ]; then
    search --no-floppy --fs-uuid --set=root --hint='cryptouuid/691c218e658f47ff82966b266b2c06c9' d1d0825c-25d1-4cbe-811f-725d9ef8d034
    else
    search --no-floppy --fs-uuid --set=root d1d0825c-25d1-4cbe-811f-725d9ef8d034
    fi
    echo 'Loading Linux linux ...'
    linux /boot/vmlinuz-linux root=UUID=d1d0825c-25d1-4cbe-811f-725d9ef8d034 rw cryptdevice=/dev/sda6:cryptroot quiet
    echo 'Loading initial ramdisk ...'
    initrd /boot/initramfs-linux.img
    menuentry 'Arch Linux, with Linux linux (fallback initramfs)' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-linux-fallback-d1d0825c-25d1-4cbe-811f-725d9ef8d034' {
    load_video
    set gfxpayload=keep
    insmod gzio
    insmod part_msdos
    insmod cryptodisk luks gcry_rijndael gcry_rijndael gcry_sha1
    insmod ext2
    set root='cryptouuid/691c218e658f47ff82966b266b2c06c9'
    if [ x$feature_platform_search_hint = xy ]; then
    search --no-floppy --fs-uuid --set=root --hint='cryptouuid/691c218e658f47ff82966b266b2c06c9' d1d0825c-25d1-4cbe-811f-725d9ef8d034
    else
    search --no-floppy --fs-uuid --set=root d1d0825c-25d1-4cbe-811f-725d9ef8d034
    fi
    echo 'Loading Linux linux ...'
    linux /boot/vmlinuz-linux root=UUID=d1d0825c-25d1-4cbe-811f-725d9ef8d034 rw cryptdevice=/dev/sda6:cryptroot quiet
    echo 'Loading initial ramdisk ...'
    initrd /boot/initramfs-linux-fallback.img
    ### END /etc/grub.d/10_linux ###
    ### BEGIN /etc/grub.d/20_linux_xen ###
    ### END /etc/grub.d/20_linux_xen ###
    ### BEGIN /etc/grub.d/30_os-prober ###
    ### END /etc/grub.d/30_os-prober ###
    ### BEGIN /etc/grub.d/40_custom ###
    # This file provides an easy way to add custom menu entries. Simply type the
    # menu entries you want to add after this comment. Be careful not to change
    # the 'exec tail' line above.
    ### END /etc/grub.d/40_custom ###
    ### BEGIN /etc/grub.d/41_custom ###
    if [ -f ${config_directory}/custom.cfg ]; then
    source ${config_directory}/custom.cfg
    elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
    source $prefix/custom.cfg;
    fi
    ### END /etc/grub.d/41_custom ###
    ### BEGIN /etc/grub.d/60_memtest86+ ###
    ### END /etc/grub.d/60_memtest86+ ###
    Things I tried:
    Replace this line in grub.cfg with
    linux /boot/vmlinuz-linux root=UUID=d1d0825c-25d1-4cbe-811f-725d9ef8d034 rw cryptdevice=UUID=d1d0825c-25d1-4cbe-811f-725d9ef8d034:cryptroot quiet
    Do mkinitcpio -p linux but the hook ecrypt is there, so I assume it's a grub issue.
    In
    /etc/default/grub
    replace GRUB_CMDLINE_LINUX="cryptdevice=/dev/sda6:cryptroot" with actual UUID, etc.
    Grub config was made with
    grub-mkconfig -o /boot/grub/grub.cfg
    Grub was installed with
    grub-install --target=i386-pc --recheck /dev/sda
    Last edited by shape (2014-07-21 15:23:05)

    Welcome to the forum :-)
    Please remember to mark the thread as solved https://bbs.archlinux.org/viewtopic.php?id=130309
    When posting configs, code or command output, please use [ code ] tags, not [ quote ] tags https://bbs.archlinux.org/help.php#bbcode
    like this
    It makes the code more readable and - in case of longer listings - more convenient to scroll through.

  • [SOLVED] No sound after fresh install

    Hi
    I am having a little bit of a problem that I couldn't solve myself. My sound is not working after a fresh installation of Arch. Everything else is fine but sound is not working. My "user" is in "audio" group, I tried some solution nothing smart just trying to reinstall or try to delete pulseaudio or alsa, only to find they are dependant on something. I have a Gnome 3.12. Also I am not an expert (obviously) ,but some things are still unclear to me about linux and this is not my first expiriance with Arch.
    This is what I belive you need from harware list:
    Motherboard: Asus P5Q PRO
    Video Card: Ati Radeon 4850HD
    Audio: Realtek ALC1200, 8-channel High Definition Audio CODEC (this is built in)
    So enough of my rambling here are the data I think you may need for actually helping me:
    This is the version I am using
    pacman -Q | grep alsa
    alsa-lib 1.0.28-1
    alsa-oss 1.0.28-1
    alsa-plugins 1.0.28-2
    alsa-utils 1.0.28-1
    lib32-alsa-lib 1.0.28-1
    lib32-alsa-plugins 1.0.28-1
    pulseaudio-alsa 2-3
    zita-alsa-pcmi 0.2.0-1.
    cat /proc/asound/modules
    0 snd_hda_intel
    1 snd_hda_intel
    lsmod | grep snd
    snd_hda_codec_realtek 67127 1
    snd_hda_codec_generic 63126 1 snd_hda_codec_realtek
    snd_hda_codec_hdmi 45117 1
    snd_hda_intel 26327 10
    snd_hda_controller 26727 1 snd_hda_intel
    snd_hda_codec 108552 5 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
    snd_hwdep 17244 1 snd_hda_codec
    snd_pcm 88487 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
    snd_timer 26614 1 snd_pcm
    snd 73436 28 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
    soundcore 13031 2 snd,snd_hda_codec
    aplay -l
    **** List of PLAYBACK Hardware Devices ****
    card 0: Intel [HDA Intel], device 0: ALC1200 Analog [ALC1200 Analog]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    card 0: Intel [HDA Intel], device 1: ALC1200 Digital [ALC1200 Digital]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    ls -l /dev/snd
    total 0
    drwxr-xr-x 2 root root 80 Oct 9 23:27 by-path
    crw-rw----+ 1 root audio 116, 5 Oct 9 23:27 controlC0
    crw-rw----+ 1 root audio 116, 2 Oct 9 23:27 controlC1
    crw-rw----+ 1 root audio 116, 10 Oct 9 23:27 hwC0D0
    crw-rw----+ 1 root audio 116, 4 Oct 9 23:27 hwC1D0
    crw-rw----+ 1 root audio 116, 7 Oct 9 23:27 pcmC0D0c
    crw-rw----+ 1 root audio 116, 6 Oct 9 23:27 pcmC0D0p
    crw-rw----+ 1 root audio 116, 8 Oct 9 23:45 pcmC0D1p
    crw-rw----+ 1 root audio 116, 9 Oct 9 23:27 pcmC0D2c
    crw-rw----+ 1 root audio 116, 3 Oct 9 23:27 pcmC1D3p
    crw-rw----+ 1 root audio 116, 1 Oct 9 23:26 seq
    crw-rw----+ 1 root audio 116, 33 Oct 9 23:27 timer
    Sorry if anything is wrong it's my first post
    Last edited by LArchimonde (2014-10-10 13:32:16)

    No, I checked that in the beggining, however the thing that bothers me is there is, in gnome settings; sound; there is no intel hd or radeonhd choises just "Digital Output" (S/PDIF) -Built-in-Audio". And I can't seem to add new one or anything else. Aslo in the same menu sound; I cannot choose another profile. Just one: Digital Stereo.
    I was thinking could the new kernel be guilty? Whenever I installed in the past everything was ok, including the sound. Now there is something that I didn't mention, there were two lines when I started installing Arch yesterday,
    "Posible missing firmware aic94, smsmdtv."
    This is not exactly how it was written but I do remeber posible and these two "missing" ones, because I writed them down.
    That's it. Anyone has any ideas?

  • [SOLVED]glibc-error after fresh install

    Hi,
    I've performed a fresh installation of Archlinux and up to the point where I run the pacman -Syu command everything is going well.
    It is then that I receive the infamous glibc-error so I followed the instructions on the wiki. However, when I enter the pacman -Syu --ignore glibc command,
    I still receive an error for pacman itself needs to be updated first. The problem is that glibc is a dependancy of pacman.
    The exact output of the "pacman -Syu --ignore glibc"
    warning: ignoring package glibc-2.16.0-2
    warning: cannot resolve "glibc>=2.15", a dependancy of pacman
    On the wiki I also found a link (http://pkgbuild.com/~allan/glibc-2.16.0 … pkg.tar.xz) to a previous version of glibc, but even then the errors remain.
    error: failed to commit transaction (conflicting files)
    glibc: /usr/bin/tzselect exists in filesystem
    glibc: /usr/sbin/zdump exists in filesystem
    glibc: /usr/sbin/zic exists in filesystem
    Any help would be appreciated. Thanks!
    Last edited by VenomGameworld (2012-07-23 13:19:04)

    http://allanmcrae.com/2012/07/updating- … e-install/

  • [SOLVED] No Sound on Fresh Install

    Well, I decided to try Arch. I was very proud of myself for managing to install everything. I even loaded KDE. I wanted to try a KDE only OS for a while.
    Well, all my pride was stomped out quicjky, in that I have no sound.  I did the following:
    1. installed: alsa-utils, alsa-oss, alsa-plugins
    2. unmuted the sound using alsamixer
    3. ran alsaconf, but found no supported drivers.
    4. Added @alsa as a daemon and rebooted
    No sound from browser. Tried an internet radio station with clementine and got:
    Could not open audio device for playback.
    Below I have tried to be helpful and posted as much output from various commands as I could. I am a newbie, and do not work in the computer indiustry. I actually do this for fun.
    Here are some outputs:
    natibo@myhost ~]$ ls -l /sys/module/snd/holders
    total 0
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_hda_codec -> ../../snd_hda_codec
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_hda_codec_hdmi -> ../../snd_hda_codec_hdmi
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_hda_codec_realtek -> ../../snd_hda_codec_realtek
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_hda_intel -> ../../snd_hda_intel
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_hwdep -> ../../snd_hwdep
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_pcm -> ../../snd_pcm
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_rawmidi -> ../../snd_rawmidi
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_seq_device -> ../../snd_seq_device
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_timer -> ../../snd_timer
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_usb_audio -> ../../snd_usb_audio
    lrwxrwxrwx 1 root root 0 Sep 24 20:00 snd_usbmidi_lib -> ../../snd_usbmidi_lib
    [natibo@myhost ~]$ cat /proc/asound/modules
    0 snd_usb_audio
    1 snd_hda_intel
    [natibo@myhost ~]$
    Some more:
    natibo@myhost ~]$ lsmod|grep '^snd' | column -t
    snd_hda_codec_hdmi 22092 1
    snd_hda_codec_realtek 294224 1
    snd_hda_intel 22122 4
    snd_hda_codec 77927 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel
    snd_usb_audio 91809 2
    snd_usbmidi_lib 18665 1 snd_usb_audio
    snd_rawmidi 19519 1 snd_usbmidi_lib
    snd_seq_device 5268 1 snd_rawmidi
    snd_hwdep 6325 2 snd_hda_codec,snd_usb_audio
    snd_pcm 73888 5 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_usb_audio
    snd_timer 19416 2 snd_pcm
    snd 57818 21 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_usb_audio,snd_usbmidi_lib,snd_rawmidi,snd_seq_device,snd_hwdep,snd_pcm,snd_timer
    snd_page_alloc 7121 2 snd_hda_intel,snd_pcm
    natibo@myhost ~]$ ls -l /dev/snd
    total 0
    drwxr-xr-x 2 root root 60 Sep 24 19:48 by-id
    drwxr-xr-x 2 root root 80 Sep 24 19:48 by-path
    crw-rw----+ 1 root audio 116, 11 Sep 24 19:48 controlC0
    crw-rw----+ 1 root audio 116, 9 Sep 24 19:48 controlC1
    crw-rw----+ 1 root audio 116, 8 Sep 24 19:48 hwC1D0
    crw-rw----+ 1 root audio 116, 7 Sep 24 19:48 hwC1D3
    crw-rw----+ 1 root audio 116, 10 Sep 24 19:49 pcmC0D0c
    crw-rw----+ 1 root audio 116, 6 Sep 24 19:49 pcmC1D0c
    crw-rw----+ 1 root audio 116, 5 Sep 24 19:50 pcmC1D0p
    crw-rw----+ 1 root audio 116, 4 Sep 24 19:50 pcmC1D1p
    crw-rw----+ 1 root audio 116, 3 Sep 24 19:48 pcmC1D2c
    crw-rw----+ 1 root audio 116, 2 Sep 24 19:48 pcmC1D3p
    crw-rw---- 1 root audio 116, 1 Sep 24 19:48 seq
    crw-rw----+ 1 root audio 116, 33 Sep 24 19:48 timer
    Last edited by natibo (2011-09-27 12:49:08)

    I tried to play a .wav but failed. I followed everything on the alsa wiki page. I can still hear the KDE test sounds quite well. My gut tells me it's got to be something simple since I can get some sound! Ugh. I don't want to give up, but I am getting closer. I did not like Chakra.
    Here is my code.
    [natibo@myhost ~]$ cat /proc/asound/modules
    1 snd_usb_audio
    2 snd_hda_intel
    [natibo@myhost ~]$
    [natibo@myhost ~]$ ls -l /sys/module/snd/holders
    total 0
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_hda_codec -> ../../snd_hda_codec
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_hda_codec_hdmi -> ../../snd_hda_codec_hdmi
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_hda_codec_realtek -> ../../snd_hda_codec_realtek
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_hda_intel -> ../../snd_hda_intel
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_hwdep -> ../../snd_hwdep
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_pcm -> ../../snd_pcm
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_rawmidi -> ../../snd_rawmidi
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_seq_device -> ../../snd_seq_device
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_timer -> ../../snd_timer
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_usb_audio -> ../../snd_usb_audio
    lrwxrwxrwx 1 root root 0 Sep 26 18:39 snd_usbmidi_lib -> ../../snd_usbmidi_lib
    natibo@myhost ~]$ aplay -l
    **** List of PLAYBACK Hardware Devices ****
    card 2: Intel [HDA Intel], device 0: ALC889 Analog [ALC889 Analog]
    Subdevices: 0/1
    Subdevice #0: subdevice #0
    card 2: Intel [HDA Intel], device 1: ALC889 Digital [ALC889 Digital]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    card 2: Intel [HDA Intel], device 3: HDMI 0 [HDMI 0]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    [natibo@myhost ~]$

  • Windows Update Fails After fresh install

    All,
    Complete new installation of Windows 7 Pro on a X200 Tablet version.  All ok, able to run all MS updates without any problems.  After installing Lenovo System update and running the actual updates, I suddenly can't run Microsoft Update any longer, showing following error msg:  "Windows Update cannot currently check for updates because the service is not running.  You possibly have to restart the pc"
    Offcourse I have tried rebooting, no success.
    Intel drivers are installed, as suggested on another page.  Currently running a systems restore to moment prior of System Update installation.
    Any ideas?
    Thanks
    Pascal
    Solved!
    Go to Solution.

    System is now working properly, even with Lenovo System Update.  Refusing to install the Intel drivers is indeed the solution.  And the system runs smooth.
    So thanks for the info!
    Pascal

  • [Solved] GRUB fails to Recall previous entry; GRUB_SAVEDEFAULT="true"

    I have used this for years even pre-archlinux.  Recently it has stopped working.
    From my /etc/default/grub
    GRUB_DEFAULT=saved
    GRUB_SAVEDEFAULT="true"
    From pacman -Qii grub
    Version : 1:2.02.beta2-1
    Architecture : x86_64
    Build Date : Sun 05 Jan 2014 11:07:40 AM PST
    Install Date : Fri 10 Jan 2014 09:00:39 AM PST
    /etc/default/grub has not changed except for add/remove GRUB_DISABLE_SUBMENU=y for the bug FS#38234
    Am I the only one experiencing this?
    Last edited by keepitsimpleengineer (2014-02-27 23:38:38)

    keepitsimpleengineer wrote:So I will change the load_env and save_env in grub.cfg to force the default grubenv and see what happens.
    After changing /boot/grub/grub.cfg so that load_env is replaced with load_env -f /boot/grub/grubenv and all save_env are changed to save_env -f /boot/grub/grubenv there is no change in behavior.
    root@kise-005 grub# pwd
    /boot/grub
    root@kise-005 grub# ls -lat
    total 398
    drwxr-xr-x 6 root root 1024 Feb 8 12:48 .
    -rw------- 1 root root 58093 Feb 8 12:48 grub.cfg
    -rw------- 1 root root 57983 Feb 8 08:54 grub.cfg.without
    -rw------- 1 root root 57983 Feb 8 08:54 grub.cfg~
    -rw------- 1 root root 58971 Feb 8 08:53 grub.cfg.with
    drwxr-xr-x 7 root root 1024 Jan 31 09:34 ..
    -rw------- 1 root root 53749 Dec 27 12:47 grub.conf
    drwxr-xr-x 2 root root 7168 Sep 7 22:53 i386-pc
    drwxr-xr-x 2 root root 1024 Sep 7 22:53 locale
    -rw-r--r-- 1 root root 4087 Aug 5 2013 grub.cfg.pacnew
    -rw------- 1 root root 45366 Jun 23 2013 grub.cfg.example
    -rw------- 1 root root 47614 May 30 2013 grub.cfg.pacsave
    drwxr-xr-x 2 root root 1024 Jul 20 2012 fonts
    -rw-r--r-- 1 root root 1024 Jul 20 2012 grubenv
    drwxr-xr-x 3 root root 1024 Jul 20 2012 themes
    --ljohnson{13:00:44}grub]$ grub-editenv grubenv list
    saved_entry=osprober-chain-545A36C35A36A1A2
    Well, I can live with this but I'm curious as to what is  happening.
    modified grub.cfg at http://pastebin.com/VdsupFfn
    /ect/default/grub at http://pastebin.com/tqmHKNvv
    Last edited by keepitsimpleengineer (2014-02-08 21:38:50)

  • [SOLVED] No internet after fresh install on laptop

    After working mostly on windows and a little on some linux distributions like Mint and Ubuntu I wanted to move on to Arch Linux after a lot of discussions about it with colleagues and my gf. I managed to install it succesfully on my desktop and everything runs smooth. My laptop didn't went as smooth though. First I had some problems to get it booting, but that problem got solved.
    Now... At home I don't seem to be able to connect to the internet with my laptop, while my desktop can connect fine. Both machines are connected with a wire on the same D-LINK router, can give the specs if needed. For both i just use the dynamic IP adress option via dhcpcd.
    It might be something simple, and I'm quite the noob, although i want to learn, so I hope someone has a clue what might be going on and how to solve it. I'm writing this topic from my desktop, as I said before, that machine has internet connection without any problem...
    Last edited by glendc (2014-02-26 00:51:28)

    glendc wrote:Ok I am available to solve the solution again for a couple of hours. So I still have no internet, and i'm home right now. Earlier today, at work, I installed networkmanager and net-tools. So I have these now too. So any suggestions on where the problem can be? I might not be describing my problem not enough, or forgetting to mention important details, I'm sorry for this, but I'm very new to this, so I don't really know what to tell and what not.
    Well....I can tell you what I had to do.
    dhcpcd works fine as long as you have an ethernet wire hooked up. My Dell has the Broadcom Wireless card, meaning I had to get the driver from the AUR. Here's how I got it done:
    Install Arch
    (leave the ethernet hooked up)
    if you have no internet and the ethernet is hooked up, issue the following command:
    sudo dhcpcd
    if you don't have your /etc/sudoers file set up just type
    su
    then enter your password,
    then enter the following command:
    dhcpcd
    ok, assuming you have internet withe the ethernet wire, install a browser. Go to the AUR, and get the "b43-firmware" download the tarbell, uncompress it, then install it using makepkg. Check the Wiki if you're not sure how to do it. Once it's installed, issue the following command:
    sudo modprobe b43
    again, if you don't have sudoers set up, you'll have to execute su, then password.
    ok...now you have wireless.
    now you have two choices to get it working,
    execute the following command to test it:
    wifi-menu
    you can sign on from there
    to sign on at boot, you'll need network manager. I see you've already installed network manager, so you just need to install the panel applet unless you're running gnome or kde (these come with it out of the box)
    issue the following three commands:
    sudo systemctl disable dhcpcd.service
    sudo systemctl stop dhcpcd.service
    sudo systemctl enable NetworkManager.service
    these commands are case-specific, so make sure you capitalize the N, and M.
    reboot, then you should have wifi show up from the panel applet.
    if not, let me know....We'll dig a little deeper.
    at any rate, whether you have a Broadcom card or not, you have to stop the dhcpcd service and start the NetworkManager service to give control to the panel applet.

  • [SOLVED] Grub freeze after Catalyst install

    Hello guys,
    I tried to switch from free to proprietary driver (Catalyst) but, despite I set the option nomodeset in the grub, the shell is frozen and I can't access anymore to my system.
    How can I install again the free driver and be again operative?
    Thanks.
    Last edited by Astroarch (2014-03-28 17:20:34)

    Sorry If I answer now.
    And yes, I run the command
    sudo aticonfig --initial
    and installed the correct version of Catalyst, not the legacy because I have an ATI Radeon 5650.
    I chrooted, removed the Catalyst, installed again the open source driver but nothing, the process is blocked after some seconds I select the GRUB voice and starts to charge the modules.
    How can I ripristine again the previous configuration?
    I am lost now.
    One thing more.
    I noticed that, despite I removed Catalyst, when I run
    atinconfig
    still works, it is not saying that is not in the system anymore.
    And this is strange.
    Update:
    as you requested, I try to explaine better what I exactly did.
    I start from a system with the open source driver (xf86-video-ati). Yesterday I decided to switch to the proprietary for gaming reasons.
    Then I followed the wiki:
    I added the repository of Vi0l0, updated pacman and then:
    sudo pacman -S catalyst-hook catalyst-utils catalyst-libgl opencl-catalyst lib32-catalyst-utils lib32-catalyst-libgl lib32-opencl-catalyst
    The installation seemed to go correctly but maybe an error could have come here, I am not sure.
    The I run:
    aticonfig --initial
    blacklisted radeon editing the file
    sudo nano /etc/modprobe.d/modprobe.conf
    adding the line
    blaclklist fglrx
    and I checked into the directory /etc/modules-load.d/, there it was a file called aticonfig with a single line containing fglrx .
    I rebooted my system, adding the option nomodeset in the linux line of my crug configuration and since then it froze.
    The system starts to load but after few processes the cursors stops to blink and then it is blocked.
    I remember that it happens after it is loading some video driver regarding screen backlight.
    I also noticed that when I chroot and then start an X session, it is unable to start it, so there is an error in the video driver.
    Now my target should be to ripristine the previous open driver.
    Then I removed Catalyst but still aticonfig is working.
    What shall I do?
    PS.
    Going back from work, later today, I will post my xorg.config file.
    Last edited by Astroarch (2014-03-28 08:13:20)

  • Login to apex_admin failed after fresh install of Apex 3.1

    I have installed Apex 3.1.
    Now i am trying to login to the admin page:
    http://host:7777/pls/apex/apex_admin
    When i submit username and password and press a login button i return to exactly the same login page.
    Apache log show the following:
    <<
    10.63.31.65 - APEX_PUBLIC_USER [14/Apr/2008:17:34:44 +0300] "POST /pls/apex/wwv_flow.accept HTTP/1.1" 302 174
    10.63.31.65 - APEX_PUBLIC_USER [14/Apr/2008:17:34:44 +0300] "GET /pls/apex/f?p=4050:3:3489699423845827 HTTP/1.1" 302 5
    10.63.31.65 - APEX_PUBLIC_USER [14/Apr/2008:17:34:44 +0300] "GET /pls/apex/f?p=4050:3:1586171788692736 HTTP/1.1" 302 5
    10.63.31.65 - APEX_PUBLIC_USER [14/Apr/2008:17:34:44 +0300] "GET /pls/apex/f?p=4550:10:1586171788692736::::FSP_AFTER_LOGIN_URL:\\f?p=4050|3|1586171788692736\\ HTTP/1.1" 302 5
    10.63.31.65 - APEX_PUBLIC_USER [14/Apr/2008:17:34:44 +0300] "GET /pls/apex/f?p=4550:10:882783301072528::::FSP_AFTER_LOGIN_URL:\\f?p=4050|3|1586171788692736\\ HTTP/1.1" 200 4709
    >>
    Any suggestions ?
    Thank you
    Michael

    I have checked the same with Mozilla browser and no problem appeared.
    The problem still exist with IE version 6
    Any ideas what can be the problem ?
    Thank you
    Michael

  • [SOLVED] Fresh Install, won't boot past grub

    I did a fresh install of Arch (GPT partitioning table) with a 8 GB root directory, 138 GB home directory, 4 GB swap, and a 1007 KB bios boot partition. Everything went well, I got through the installation with no problems, but when I rebooted the computer. It showed this after the grub menu: https://lh6.googleusercontent.com/-UM-3 … 2014-06-22
    So now my question is, was I supposed to do anything extra during the installation process? Or is this a hardware problem? Linux Mint, Ubuntu, Lubuntu, and Zorin OS works fine so I'm assuming I need to do something extra during installation...
    Last edited by ryukiri (2014-07-03 21:44:44)

    Trilby wrote:
    ryukiri wrote:That only tells me how to make it a boot option...I assume I need to be chrooted from the install CD to do this.
    You can do it one of two ways: boot the install cd/usb, mount all the partitions as in the original installation process, then chroot.  From there you can just use pacman to install packages as it it were a normal system: `pacman -S linux-lts`.
    There is, however, no need for the chroot.  The alternative, and somewhat simpler, approach would be to boot the install media and mount the partitions as above, then use the pacstrap tool just like you did when installing the 'base' group: `pacstrap -i /mnt linux-lts`.
    I think it is safer to arch-chroot because you still need to be chrooted to generate your grub.cfg "grub-mkconfig -o /boot/grub/grub.cfg"
    Last edited by ugjka (2014-07-03 08:24:30)

Maybe you are looking for