[SOLVED: HW ISSUE] WLAN no longer works (Zotac IQ01 / r8169 / iwlwifi)

After recent (since 9.7.2014) updates, the WLAN link stopped working for me - and I don't seem to be find a way to restore it. Thus, your wisdom is appreciated:
Setup/Background
- Device: Zotac ZBox IQ (http://www.zotac.com/products/mini-pcs/ … nt/10.html)
- Network device (2xGLAN): Realtek RTL8111/8168/8411 (kernel module r8169 loads)
- Wifi (device missing, used to work as enp3s0 ??), should be intel chipset
- Wired connection works
- NetworkManager is in use
- Dmesg error: enp3s0 link is not ready
Tried so far
- Tested with older kernel 3.14.x -- no change
- Tested with kernel-lts -- no change
- Tested with older networkmanager -- no change
- Tested with fresh Arch media (latest.iso) -- device cannot be found
- Tested with older Arch media (1.4.2014.iso) -- device cannot be found
- Tried bringing up the link with command: ip link set dev enp3s0 up -- no change, no error
- Unloading r8169 removes the wired connection in networkmanager but not wireless, is that normal?
- Noticed also this link (https://wiki.archlinux.org/index.php/Ne … OL_problem), but setup has no Windows
Any pointers? Had a similar problem sometime in the past (https://bbs.archlinux.org/viewtopic.php?id=177793 -- different device), and then after some time and upgrades it just started working again.
Thanks in advance,
Juha
[EDIT 14.7]
Removed misleading reference: Noticed this post (https://bbs.archlinux.org/viewtopic.php?id=183601) and changed name in udev rules: enp03s0 -> wlp03s0 -- no change
[EDIT 16.7]
Added some details seen also later in thread
Last edited by jmu (2014-07-18 16:08:45)

jmu wrote:
Sorry for missing your guidance ewaller, but you mean this?
Let's try again:
sudo iw wlp3s0 scan
(iw help output)
Apparently it requires dev parameter?
sudo iw dev wlp3s0 scan
command failed: No such device (-19)
ewaller$@$odin ~ 1012 %sudo iw wlan0 scan
[sudo] password for ewaller:
BSS c4:3d:c7:5d:eb:8f(on wlan0) -- associated
TSF: 142129421052 usec (1d, 15:28:49)
freq: 2412
beacon interval: 100 TUs
capability: ESS Privacy ShortSlotTime (0x0411)
signal: -42.00 dBm
last seen: 260 ms ago
Information elements from Probe Response frame:
SSID: Woodlyn
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 1
ERP: <no flags>
ERP D4.0: <no flags>
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
Extended supported rates: 6.0 9.0 12.0 48.0
HT capabilities:
Capabilities: 0x187c
HT20
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 1
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: non-HT mixed
* non-GF present: 1
* OBSS non-GF present: 1
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 78:54:2e:17:d3:ee(on wlan0)
TSF: 18945414335000 usec (219d, 06:36:54)
freq: 2412
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime (0x0431)
signal: -84.00 dBm
last seen: 193 ms ago
Information elements from Probe Response frame:
SSID: mcfab
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Parameter set: channel 1
Country: US Environment: Indoor/Outdoor
Channels [1 - 11] @ 30 dBm
ERP: Use_Protection Barker_Preamble_Mode
Extended supported rates: 24.0 36.0 48.0 54.0
HT capabilities:
Capabilities: 0x1ad
RX LDPC
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 1
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: non-HT mixed
* non-GF present: 0
* OBSS non-GF present: 1
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Overlapping BSS scan params:
* passive dwell: 20 TUs
* active dwell: 10 TUs
* channel width trigger scan interval: 300 s
* scan passive total per channel: 200 TUs
* scan active total per channel: 20 TUs
* BSS width channel transition delay factor: 5
* OBSS Scan Activity Threshold: 0.25 %
Extended capabilities: HT Information Exchange Supported
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
RSN: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
WPA: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* Response Type: 3 (AP)
* UUID: 13c0b07c-1dd2-11b2-8c69-91034a198fdd
* Manufacturer: D-Link
* Model: D-Link Repeater
* Model Number: DAP-1320
* Serial Number: none
* Primary Device Type: 6-0050f204-1
* Device name: DAP-1320
* Config methods: PBC
* RF Bands: 0x1
* Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
BSS 58:6d:8f:1c:7f:f5(on wlan0)
TSF: 369471980976 usec (4d, 06:37:51)
freq: 2422
beacon interval: 100 TUs
capability: ESS Privacy ShortSlotTime (0x0411)
signal: -82.00 dBm
last seen: 3106 ms ago
Information elements from Probe Response frame:
SSID: Merlin
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 3
ERP: <no flags>
ERP D4.0: <no flags>
RSN: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
Extended supported rates: 6.0 9.0 12.0 48.0
HT capabilities:
Capabilities: 0x18fc
HT20
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 3
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: non-HT mixed
* non-GF present: 1
* OBSS non-GF present: 1
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* Response Type: 3 (AP)
* UUID: c18a4b3e-6832-34c7-2859-7ccb974a11a7
* Manufacturer: Cisco
* Model: Linksys E3200
* Model Number: v1.0.04
* Serial Number: 42
* Primary Device Type: 6-0050f204-1
* Device name: Linksys E3200
* Config methods: Display, PBC
* RF Bands: 0x3
* Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
WPA: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
BSS b8:e6:25:f7:1d:29(on wlan0)
TSF: 1088585492128 usec (12d, 14:23:05)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime (0x0431)
signal: -79.00 dBm
last seen: 30 ms ago
Information elements from Probe Response frame:
SSID: 2WIRE883
Supported rates: 1.0* 2.0* 5.5* 6.0 9.0 11.0* 12.0 18.0
DS Parameter set: channel 11
Country: US Environment: Indoor/Outdoor
Channels [1 - 11] @ 27 dBm
RSN: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
WPA: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
ERP: <no flags>
Extended supported rates: 24.0 36.0 48.0 54.0
BSS c4:04:15:8f:29:a0(on wlan0)
TSF: 1092012544384 usec (12d, 15:20:12)
freq: 2447
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime (0x0431)
signal: -84.00 dBm
last seen: 1170 ms ago
Information elements from Probe Response frame:
SSID: MyCharterWiFia0-2G
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Parameter set: channel 8
TIM: DTIM Count 0 DTIM Period 2 Bitmap Control 0x0 Bitmap[0] 0x4
ERP: <no flags>
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
Extended supported rates: 24.0 36.0 48.0 54.0
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
HT capabilities:
Capabilities: 0x11cc
HT20
SM Power Save disabled
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 8
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 1
* HT protection: no
* non-GF present: 0
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Overlapping BSS scan params:
* passive dwell: 20 TUs
* active dwell: 10 TUs
* channel width trigger scan interval: 300 s
* scan passive total per channel: 200 TUs
* scan active total per channel: 20 TUs
* BSS width channel transition delay factor: 5
* OBSS Scan Activity Threshold: 0.25 %
Extended capabilities: HT Information Exchange Supported
BSS 00:1a:ef:0a:1f:1c(on wlan0)
TSF: 1456596480215 usec (16d, 20:36:36)
freq: 2412
beacon interval: 100 TUs
capability: ESS Privacy ShortSlotTime (0x0411)
signal: -90.00 dBm
last seen: 1503 ms ago
Information elements from Probe Response frame:
SSID: MEJ
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Parameter set: channel 1
TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x20
ERP: Barker_Preamble_Mode
Extended supported rates: 24.0 36.0 48.0 54.0
HT capabilities:
Capabilities: 0x186e
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 32767 bytes (exponent: 0x002)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 1
* secondary channel offset: above
* STA channel width: any
* RIFS: 0
* HT protection: non-HT mixed
* non-GF present: 0
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
BSS e4:f4:c6:0a:52:e0(on wlan0)
TSF: 105656013203 usec (1d, 05:20:56)
freq: 2412
beacon interval: 100 TUs
capability: ESS Privacy ShortSlotTime RadioMeasure (0x1411)
signal: -85.00 dBm
last seen: 236 ms ago
Information elements from Probe Response frame:
SSID: NETGEAR98
Supported rates: 1.0* 2.0* 5.5 11.0 18.0 24.0 36.0 54.0
DS Parameter set: channel 1
TIM: DTIM Count 1 DTIM Period 2 Bitmap Control 0x0 Bitmap[0] 0x0
ERP: <no flags>
ERP D4.0: <no flags>
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
Extended supported rates: 6.0 9.0 12.0 48.0
BSS Load:
* station count: 6
* channel utilisation: 27/255
* available admission capacity: 0 [*32us]
HT capabilities:
Capabilities: 0x19ad
RX LDPC
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 1
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 1
* HT protection: nonmember
* non-GF present: 1
* OBSS non-GF present: 1
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Overlapping BSS scan params:
* passive dwell: 20 TUs
* active dwell: 10 TUs
* channel width trigger scan interval: 300 s
* scan passive total per channel: 200 TUs
* scan active total per channel: 20 TUs
* BSS width channel transition delay factor: 5
* OBSS Scan Activity Threshold: 0.25 %
Extended capabilities: HT Information Exchange Supported, Extended Channel Switching, BSS Transition, 6
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* UUID: 14ac5004-9685-bde7-cca3-7f46f9cc6964
* RF Bands: 0x3
* Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 6016 usec
* VO: CW 3-7, AIFSN 2, TXOP 3264 usec
BSS ac:5d:10:66:64:e9(on wlan0)
TSF: 568059494785 usec (6d, 13:47:39)
freq: 2432
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime (0x0431)
signal: -84.00 dBm
last seen: 2350 ms ago
Information elements from Probe Response frame:
SSID: 2WIRE929
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Parameter set: channel 5
TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
Country: US Environment: Indoor/Outdoor
Channels [1 - 11] @ 27 dBm
ERP: <no flags>
RSN: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
WPA: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
Extended supported rates: 24.0 36.0 48.0 54.0
ewaller$@$odin ~ 1013 %
Nope.

Similar Messages

[SOLVED] hdparm -S 241 no longer working

Sometime in the last month, hdparm has stopped spinning down defined HDD's. I have a total of three HDD's in my system. Al rotating media. Two of those HDD's I use for backup, and as such are not needed for most of the day.
In my rc.local I have:
hdparm -S 241 /dev/sdb
hdparm -S 241 /dev/sdc
Under the 2.6.27 series of kernels it worked, and now under the 2.6.38 series it no longer functions.
BUT...there has been a lot of updates since then as well so it may not be a kernel issue.
As a test, I rebooted my system, launched LXDE, launched nothing else except a terminal window. I made myself root, and issued the above commands manually and then I went away for an hour. The drives did not spindown as requested. The 241 parameter decodes to 30 minutes.
Does any one have any ideas what's up?
Thank you for your assistance.
Sincerely and respectfully,
Dave
Last edited by dcbdbis (2011-04-23 03:31:40)

Solved!
And an explanation is due......
Culprit = Thunar, the XFCE file manager.
About one month ago, I made a significant change to my system. When I learned that Gnome 2 (my DE) was not going to be maintained, and that Gnome 3 was going to be force-fed to all Gnome users, I wiped my system and performed a complete fresh install and went with LXDE.
I looked at Gnome 3 after it was released via a live OpenSuse CD. It's not at all what I want, and it broke to many desktop paradigms for me personally. This is not a good vs evil thing as many are portraying Gnome 3, well at least it's not in my mind.
It's about choice. I use Arch for my daily work. I'm nearly 60 years old. I have no interest in having my desktop look like a smartphone. So I looked at KDE and LXDE. KDE can be customized much more easily than LXDE, but again it's a little too "heavy" for my personal tastes.
In the end I went with LXDE. PcManFm does not have a tree view in the left-hand pane. Thunar does. So Thunar got the nod as my file manager of choice.
I have discovered with the assistance of 'iotop' that when you open Thunar, it goes out and refreshes itself (I suspect the dir tree) with regard to every mounted file system. And as my backups, sdb1 and sdc1 were mounted, they had a read event. Your suggestion of iotop documented this. Apparently Gnome 2's 'Nautilus' file manager does not do this, because under Gnome 2, the drives spun down in accordance with my hdparm settings in the /etc/rc.local file.
My personal solution is simple. I changed my /etc/fstab and added the noauto to the line for these two drives. They do not get mounted, and in tests, Thunar doesn't attempt to automount them (I did not install the volume addon), and I also turned off the mounting features in pcmanfm.
Problem solved. The drives no longer have read events everytime I open Thunar, and spin down as they should.
For others, a second solution would be to leave the /etc/fstab alone, and simply unmount the backup drive(s) when you know you will not be using them for a while.
'iotop' did the trick for me in identifying the problem.
Thank you sincerely for the assistance. I appreciate it!
Dave.....
Last edited by dcbdbis (2011-04-23 03:39:09)

[SOLVED] Default audio device no longer works after reboot

After today's reboot, the audio device no longer works. E.g., VLC says:
Audio output failed:
The audio device "default" could not be used:
No such file or directory.
This is the console log:
[0x1394138] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface.
Fontconfig warning: "/etc/fonts/conf.d/50-user.conf", line 9: reading configurations from ~/.fonts.conf is deprecated.
[0x7fac180069c8] pulse audio output error: PulseAudio server connection failure: Connection refused
ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave
[0x7fac180069c8] alsa audio output error: cannot open ALSA device "default": No such file or directory
[0x7fac180069c8] jack audio output error: failed to connect to JACK server
[0x7fac180069c8] oss audio output error: cannot open audio device (/dev/dsp)
[0x7fac180069c8] main audio output error: no suitable audio output module
[0x7fac40fa4db8] main decoder error: failed to create audio output
[0x7fac180069c8] pulse audio output error: PulseAudio server connection failure: Connection refused
ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave
[0x7fac180069c8] alsa audio output error: cannot open ALSA device "default": No such file or directory
[0x7fac180069c8] jack audio output error: failed to connect to JACK server
[0x7fac180069c8] oss audio output error: cannot open audio device (/dev/dsp)
[0x7fac180069c8] main audio output error: no suitable audio output module
[0x7fac41055118] main decoder error: failed to create audio output
The strange thing is that the sound card does in fact work; e.g. the sound test for "HDA Intel PCH", the first entry in my KDE Audio Settings, works. But the entry "default" does not and I suppose that is also the device that VLC is complaining about.
I've tried blacklisting the HDMI driver and switched to the other audio output modules in VLC. I've also checked I'm still member of the "audio" group.
Edit:
P.S. Solved this myself. I had a USB-to-MIDI adapter cable plugged in during boot, which seems to have been causing these problems. I suppose systemd thought it was a USB sound card? I was wondering why dmesg said something about USB sound when the computer doesn't have any USB sound devices. Hardware detection epic fail. Although I guess the cable counts as a MIDI device at least, so in a way it's correct.
So it looks like I'll always have to unplug the MIDI cable before rebooting.
Last edited by Morn (2012-11-23 19:24:00)

You might get. Ore assistance in a different forum area. Maybe try Using pad. This is the forum for iPhoto for iOS.

Kernel 2.6.39.1-1 issues: reboot no longer working

I recently upgraded from kernel 2.6.38.7-1 to 2.6.39.1-1 , and have observed that this has caused reboot to no longer work. Specifically, issuing "reboot -n" kicks off the shutdown process ok, and I see the shutdown procedure getting broadcast to the interactive users, but this then hangs at the very last step, where it says Restarting.
This used to work fine, and I have confirmed that a downgrade back to 2.6.38.7-1 fixes this for me. All other packages from core and extra are up-to-date as of the time of this post.
The hardware is a fit-pc2 (i.e. intel atom-based). Is this a known upstream bug?
Last edited by stripwax (2011-06-16 20:35:25)

Thanks for replies.
@stlarch : what information would be most useful? Happy to provide whatever might be relevant. Hopefully the below helps
1. I use laptop-mode-tools with everything enabled even for AC power and acpi-cpufreq.
2. both "shutdown -r now" and "reboot" work fine if I downgrade just the kernel back to 2.6.38.7-1 . They both don't work (i.e. hang instead of reboot) if I upgrade just the kernel to 2.6.39.1-1
3. It's all worked out of the box for me for the last 6 months or so, and only the latest 2.6.39.1-1 kernel has this problem, hence why I suspect it's a regression.
4. Assuming wm means window manager: none. I don't even have X installed. This is purely a headless server, run unattended and rebooted (when necessary) remotely via ssh.
5. My dmesg reports "Selecting BIOS-method for reboots." - regardless of kernel version (i.e. when running both versions mentioned)
6. No clues in the logs unfortunately leap out to me. Let me know if there's a specific logfile that might have clues. With both a successful reboot (on older kernel) and failed reboot (on the newer kernel) the last few lines of everything.log say the same thing:
Jun 11 16:30:33 Xxxx shutdown[1600]: shutting down for system reboot
Jun 11 16:30:33 Xxxx init: Switching to runlevel: 6
Jun 11 16:30:34 Xxxx nmbd[1060]: [2011/06/11 16:30:34.651659, 0] nmbd/nmbd.c:71(terminate)
Jun 11 16:30:34 Xxxx nmbd[1060]: Got SIGTERM: going down...
Jun 11 16:30:35 Xxxx laptop-mode: Laptop mode
Jun 11 16:30:35 Xxxx laptop-mode: disabled, not active
Jun 11 16:30:36 Xxxx kernel: [ 1605.732274] r8169 0000:02:00.0: PME# enabled
Jun 11 16:30:36 Xxxx syslog-ng[522]: Termination requested via signal, terminating;
Jun 11 16:30:36 Xxxx syslog-ng[522]: syslog-ng shutting down; version='3.2.4'
@brebs: As above, this works/doesn't work dependent solely on version of kernel26 package. Is there a kernel change between those two versions that would require me changing my kernel options? I'd like to understand what caused the regression and see if there's an upstream fix (or raise it as an upstream issue if not), rather than just a reconfiguration/workaround.

[Solved] Suspend to RAM no longer works

Suspend to RAM when closing my laptop lid worked out the box for me since I put Arch on my Dell XPS 14. After doing a pacman -Su yesterday (where I noticed that the kernel was updated, but it might be something else) it no longer works. Running 'systemctl suspend' in the terminal does work. Do I have to update a config?
Last edited by skip (2014-04-01 19:48:23)

For anyone else that finds this, systemd 212 doesn't suspend with lid closed with or without external monitor for those using the Nvidia proprietary drivers. Nvidia doesn't provide the necessary information for systemd to know whether or not an external monitor is connected, and thus it plays it safe and doesn't suspend. This is explained nicely at the Freedesktop bug linked above, but I wanted to pass it along here for those that won't follow the link.
Sounds like they're leaning toward reversing the preference (dock/external display users will need to opt out of suspending with lid close) in future versions since non-dock/monitor users >> dock/monitor users.

[Solved] KDE Desktop Effects no longer working

Hello,
I just did an update, (I didn't think it was a major one, I don't recall seeing graphics update, though I'm not sure how to confirm - is there a way to see recently updated packages in yaourt?) and after a brief issue with powertop that was solved by a restart (https://bbs.archlinux.org/viewtopic.php?id=179789 - it may be unrelated though) I found that when I restarted, KWin Crashed, and since then, my desktop effects are not working.
I have gone to the KDE Desktop Effects Settings Menu, and under the advanced menu, set the compositing type back to OpenGL 3.1, clicked apply, and confirmed that I wanted to try it even though it had evidently crashed Kwin. I then received a message stating "21 desktop effects could not be loaded". When I clicked details, a popup window said:
"For technical reasons it is not possible to determine all possible error causes.
Desktop effect system is not running."
For the record, I am on a Thinkpad X201 with intel graphics.
Any ideas?
Last edited by TheGuyWithTheFace (2014-04-19 07:35:43)

Some Extra information:
I just tried a restart, that didn't work.
I then went back into effect settings, and saw that "enable effects at startup" was not checked. I also saw that under the advanced settings, Qt Graphics system was set to raster. Since I'm not sure which it was supposed to be on originally, but the current configuration wasn't working, I also set that to Native, and then clicked apply. KWin then crashed, here is the output:
Application: KWin (kwin), signal: Aborted
Using host libthread_db library "/usr/lib/libthread_db.so.1".
To enable execution of this file add
add-auto-load-safe-path /usr/lib/libstdc++.so.6.0.19-gdb.py
line to your configuration file "/home/perry/.gdbinit".
To completely disable this security protection add
set auto-load safe-path /
line to your configuration file "/home/perry/.gdbinit".
For more information about this security protection see the
"Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
info "(gdb)Auto-loading safe path"
[Current thread is 1 (Thread 0x7fafaa788800 (LWP 796))]
Thread 4 (Thread 0x7faf8beb3700 (LWP 797)):
#0 0x00007fafa3f7e3f8 in pthread_cond_timedwait@@GLIBC_2.3.2 () from /usr/lib/libpthread.so.0
#1 0x00007fafa420a034 in QWaitCondition::wait(QMutex*, unsigned long) () from /usr/lib/libQtCore.so.4
#2 0x00007fafa41fd745 in ?? () from /usr/lib/libQtCore.so.4
#3 0x00007fafa4209b7f in ?? () from /usr/lib/libQtCore.so.4
#4 0x00007fafa3f7a0a2 in start_thread () from /usr/lib/libpthread.so.0
#5 0x00007fafa9fa9d1d in clone () from /usr/lib/libc.so.6
Thread 3 (Thread 0x7faf8b27a700 (LWP 798)):
#0 0x00007fafa3f7e3f8 in pthread_cond_timedwait@@GLIBC_2.3.2 () from /usr/lib/libpthread.so.0
#1 0x00007fafa420a034 in QWaitCondition::wait(QMutex*, unsigned long) () from /usr/lib/libQtCore.so.4
#2 0x00007fafa41fd745 in ?? () from /usr/lib/libQtCore.so.4
#3 0x00007fafa4209b7f in ?? () from /usr/lib/libQtCore.so.4
#4 0x00007fafa3f7a0a2 in start_thread () from /usr/lib/libpthread.so.0
#5 0x00007fafa9fa9d1d in clone () from /usr/lib/libc.so.6
Thread 2 (Thread 0x7faf8a878700 (LWP 799)):
#0 0x00007fafa9fa2fd3 in select () from /usr/lib/libc.so.6
#1 0x00007fafa42e6c13 in ?? () from /usr/lib/libQtCore.so.4
#2 0x00007fafa4209b7f in ?? () from /usr/lib/libQtCore.so.4
#3 0x00007fafa3f7a0a2 in start_thread () from /usr/lib/libpthread.so.0
#4 0x00007fafa9fa9d1d in clone () from /usr/lib/libc.so.6
Thread 1 (Thread 0x7fafaa788800 (LWP 796)):
[KCrash Handler]
#5 0x00007fafa9ef9389 in raise () from /usr/lib/libc.so.6
#6 0x00007fafa9efa788 in abort () from /usr/lib/libc.so.6
#7 0x00007fafa9ef24a6 in __assert_fail_base () from /usr/lib/libc.so.6
#8 0x00007fafa9ef2552 in __assert_fail () from /usr/lib/libc.so.6
#9 0x00007fafa7d6f8d9 in ?? () from /usr/lib/libX11.so.6
#10 0x00007fafa7d6f96e in ?? () from /usr/lib/libX11.so.6
#11 0x00007fafa7d6fc4d in _XEventsQueued () from /usr/lib/libX11.so.6
#12 0x00007fafa7d72905 in _XGetRequest () from /usr/lib/libX11.so.6
#13 0x00007fafa4dfe587 in ?? () from /usr/lib/libGL.so.1
#14 0x00007fafa4dfbf6b in ?? () from /usr/lib/libGL.so.1
#15 0x00007faf89bef6db in ?? () from /usr/lib/xorg/modules/dri/i965_dri.so
#16 0x00007faf89befa33 in ?? () from /usr/lib/xorg/modules/dri/i965_dri.so
#17 0x00007faf89befb8b in ?? () from /usr/lib/xorg/modules/dri/i965_dri.so
#18 0x00007faf89b89ef6 in ?? () from /usr/lib/xorg/modules/dri/i965_dri.so
#19 0x00007fafa4dfd898 in ?? () from /usr/lib/libGL.so.1
#20 0x00007fafa4dd804c in glXMakeCurrentReadSGI () from /usr/lib/libGL.so.1
#21 0x00007fafaa34e479 in ?? () from /usr/lib/libkdeinit4_kwin.so
#22 0x00007fafaa350029 in ?? () from /usr/lib/libkdeinit4_kwin.so
#23 0x00007fafaa34aefc in ?? () from /usr/lib/libkdeinit4_kwin.so
#24 0x00007fafaa32f4b5 in ?? () from /usr/lib/libkdeinit4_kwin.so
#25 0x00007fafaa2b6c75 in ?? () from /usr/lib/libkdeinit4_kwin.so
#26 0x00007fafa431d6ea in QMetaObject::activate(QObject*, QMetaObject const*, int, void**) () from /usr/lib/libQtCore.so.4
#27 0x00007fafa41fa958 in QFutureWatcherBase::event(QEvent*) () from /usr/lib/libQtCore.so.4
#28 0x00007fafa3491f0c in QApplicationPrivate::notify_helper(QObject*, QEvent*) () from /usr/lib/libQtGui.so.4
#29 0x00007fafa34984d0 in QApplication::notify(QObject*, QEvent*) () from /usr/lib/libQtGui.so.4
#30 0x00007fafa8bfa88a in KApplication::notify(QObject*, QEvent*) () from /usr/lib/libkdeui.so.5
#31 0x00007fafa4309a6d in QCoreApplication::notifyInternal(QObject*, QEvent*) () from /usr/lib/libQtCore.so.4
#32 0x00007fafa430caad in QCoreApplicationPrivate::sendPostedEvents(QObject*, int, QThreadData*) () from /usr/lib/libQtCore.so.4
#33 0x00007fafa352f71c in ?? () from /usr/lib/libQtGui.so.4
#34 0x00007fafa43086cf in QEventLoop::processEvents(QFlags<QEventLoop::ProcessEventsFlag>) () from /usr/lib/libQtCore.so.4
#35 0x00007fafa43089c5 in QEventLoop::exec(QFlags<QEventLoop::ProcessEventsFlag>) () from /usr/lib/libQtCore.so.4
#36 0x00007fafa430dae9 in QCoreApplication::exec() () from /usr/lib/libQtCore.so.4
#37 0x00007fafaa2e7896 in kdemain () from /usr/lib/libkdeinit4_kwin.so
#38 0x00007fafa9ee5b05 in __libc_start_main () from /usr/lib/libc.so.6
#39 0x00000000004006fe in _start ()

[SOLVED] ACPI handler.sh no longer working (Thinkpad X60 Tablet)

Hello there,
I recently did a few updates on my system to reduce power usage and get hdaps working. For some reason one of these changes must have broken ACPID in some way so that what I wrote in handler.sh no longer has any effect when I e.g. press the configured buttons to lock my screen or shut down, but I have no clue which.
I'm not really familiar with where ACPI and ACPID keeps all their logs either, and which parts in there might mean something for me. I don't even know how I can check if ACPI is running properly and just ACPID isn't, for instance (both are running thought, confirmed with ps -A).
Here's what I can remember of what I did:
-full system update
-install cpufreq to redcude power usage with acpi_cpufreq
-install HDAPS with Thinkpad driver, as described on the Wiki
-tweak my laptop-mode settings, e.g. disable VGA output when in laptop mode
-enable AHCI for my hard drive in kernel image and BIOS
Would be great if you could help me troubleshoot this somehow, as I really don't have a clue on how to fix this. Here's some output that might be helpful for starters:
cat /etc/acpi/handler.sh
#!/bin/sh
set $*
case "$1" in
button/power)
#echo "PowerButton pressed!">/dev/tty5
case "$2" in
PWRF)
#Power off
shutdown -h now
logger "ACPI action undefined: $2"
esac
ibm/hotkey)
#echo "Display swiveled">/dev/tty5
case "$2" in
HKEY)
case "$4" in
00005009)
#Swiveling down
/bin/sh /etc/acpi/actions/swivel-down
0000500a)
#Swiveling up
/bin/sh /etc/acpi/actions/swivel-up
00001002)
#Lock screen
xscreensaver-command -lock
#run_once xtrlock &
00001004)
#Standby button
xscreensaver-command -lock ; s2ram
00001005)
#Network button
/etc/rc.d/net-auto-wireless restart
00001009)
#Reboot
shutdown -r now
00007000)
#WLan button switched
/etc/rc.d/net-auto-wireless restart
fi
esac
esac
button/sleep)
case "$2" in
SLPB) echo -n mem >/sys/power/state ;;
*) logger "ACPI action undefined: $2" ;;
esac
ac_adapter)
case "$2" in
AC)
case "$4" in
00000000)
#laptop mode should take care of this alone!
#/etc/rc.d/laptop-mode start
00000001)
#/etc/rc.d/laptop-mode stop
esac
*) logger "ACPI action undefined: $2" ;;
esac
battery)
case "$2" in
BAT0)
case "$4" in
00000000) #echo "offline" >/dev/tty5
00000001) #echo "online" >/dev/tty5
esac
CPU0)
*) logger "ACPI action undefined: $2" ;;
esac
button/lid)
#echo "LID switched!">/dev/tty5
case "$2" in
LID)
if [[ `cat /proc/acpi/button/lid/LID/state | awk '{print $2}'` = "closed" ]]
then
#run_once xtrlock &
xscreensaver-command -lock
fi
esac
logger "ACPI group/action undefined: $1 / $2"
esac
dmesg | grep acpi
BIOS-e820: 000000007f6d0000 - 000000007f6df000 (ACPI data)
BIOS-e820: 000000007f6df000 - 000000007f700000 (ACPI NVS)
modified: 000000007f6d0000 - 000000007f6df000 (ACPI data)
modified: 000000007f6df000 - 000000007f700000 (ACPI NVS)
ACPI: RSDP 000f67c0 00024 (v02 LENOVO)
ACPI: XSDT 7f6d11e8 0008C (v01 LENOVO TP-7J 00001140 LTP 00000000)
ACPI: FACP 7f6d1300 000F4 (v03 LENOVO TP-7J 00001140 LNVO 00000001)
ACPI Warning: 32/64X length mismatch in Gpe1Block: 0/32 (20090903/tbfadt-526)
ACPI Warning: Optional field Gpe1Block has zero address or length: 000000000000102C/0 (20090903/tbfadt-557)
ACPI: DSDT 7f6d1690 0D56F (v01 LENOVO TP-7J 00001140 MSFT 0100000E)
ACPI: FACS 7f6f4000 00040
ACPI: SSDT 7f6d14b4 001DC (v01 LENOVO TP-7J 00001140 MSFT 0100000E)
ACPI: ECDT 7f6debff 00052 (v01 LENOVO TP-7J 00001140 LNVO 00000001)
ACPI: TCPA 7f6dec51 00032 (v02 LENOVO TP-7J 00001140 LNVO 00000001)
ACPI: APIC 7f6dec83 00068 (v01 LENOVO TP-7J 00001140 LNVO 00000001)
ACPI: MCFG 7f6deceb 0003C (v01 LENOVO TP-7J 00001140 LNVO 00000001)
ACPI: HPET 7f6ded27 00038 (v01 LENOVO TP-7J 00001140 LNVO 00000001)
ACPI: SLIC 7f6dee62 00176 (v01 LENOVO TP-7J 00001140 LTP 00000000)
ACPI: BOOT 7f6defd8 00028 (v01 LENOVO TP-7J 00001140 LTP 00000001)
ACPI: SSDT 7f6f2603 0025F (v01 LENOVO TP-7J 00001140 INTL 20050513)
ACPI: SSDT 7f6f2862 000A6 (v01 LENOVO TP-7J 00001140 INTL 20050513)
ACPI: SSDT 7f6f2908 004F7 (v01 LENOVO TP-7J 00001140 INTL 20050513)
ACPI: SSDT 7f6f2dff 001D8 (v01 LENOVO TP-7J 00001140 INTL 20050513)
ACPI: Local APIC address 0xfee00000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
ACPI: Core revision 20090903
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
ACPI: EC: EC description table is found, configuring boot EC
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: Power Resource [PUBS] (on)
ACPI: ACPI Dock Station Driver: 3 docks/bays found
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
PCI: Using ACPI for IRQ routing
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
acpi device:01: registered as cooling_device0
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Lid Switch [LID]
ACPI: Sleep Button [SLPB]
ACPI: Power Button [PWRF]
i915 0000:00:02.0: power state changed by ACPI to D0
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
ACPI: SSDT 7f6f1ccc 001FE (v01 PmRef Cpu0Ist 00000100 INTL 20050513)
ACPI: SSDT 7f6f1f4f 006B4 (v01 PmRef Cpu0Cst 00000100 INTL 20050513)
ACPI: SSDT 7f6f1c04 000C8 (v01 PmRef Cpu1Ist 00000100 INTL 20050513)
ACPI: SSDT 7f6f1eca 00085 (v01 PmRef Cpu1Cst 00000100 INTL 20050513)
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
ACPI: Thermal Zone [THM0] (56 C)
ACPI: Thermal Zone [THM1] (59 C)
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
thinkpad_acpi: ThinkPad ACPI Extras v0.23
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 7JET29WW (1.14 ), EC 7JHT13WW-1.04
thinkpad_acpi: Lenovo ThinkPad X60 Tablet, model 6363WDK
thinkpad_acpi: WARNING: Outdated ThinkPad BIOS/EC firmware
thinkpad_acpi: WARNING: This firmware may be missing critical bug fixes and/or important features
thinkpad_acpi: ACPI backlight control delay disabled
thinkpad_acpi: radio switch found; radios are enabled
thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode
thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
Registered led device: tpacpi::thinklight
Registered led device: tpacpi::power
Registered led device: tpacpi::standby
Registered led device: tpacpi::thinkvantage
thinkpad_acpi: Standard ACPI backlight interface available, not loading native one.
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
cat /var/log/acpid.log
Feb 28 13:19:28 damnation acpid: exiting
Mar 1 12:48:43 damnation acpid: starting up
Mar 1 12:48:43 damnation acpid: 4 rules loaded
Mar 1 12:48:43 damnation acpid: waiting for events: event logging is off
Mar 1 12:48:44 damnation acpid: client connected from 1737[82:82]
Mar 1 12:48:44 damnation acpid: 1 client rule loaded
Mar 1 12:49:39 damnation acpid: client connected from 2523[0:0]
Mar 1 12:49:39 damnation acpid: 1 client rule loaded
Mar 1 12:49:56 damnation acpid: exiting
Mar 1 12:49:56 damnation acpid: starting up
Mar 1 12:49:56 damnation acpid: 4 rules loaded
Mar 1 12:49:56 damnation acpid: waiting for events: event logging is off
Mar 1 12:49:57 damnation acpid: client connected from 2523[0:0]
Mar 1 12:49:57 damnation acpid: 1 client rule loaded
Mar 1 12:50:01 damnation acpid: client connected from 1737[82:82]
Mar 1 12:50:01 damnation acpid: 1 client rule loaded
Mar 2 10:23:50 damnation acpid: client 2523[0:0] has disconnected
Mar 2 10:23:50 damnation acpid: client connected from 2523[0:0]
Mar 2 10:23:50 damnation acpid: 1 client rule loaded
Mar 2 10:52:18 damnation acpid: client 2523[0:0] has disconnected
Mar 2 10:52:18 damnation acpid: client connected from 2523[0:0]
Mar 2 10:52:18 damnation acpid: 1 client rule loaded
Mar 2 17:00:21 damnation acpid: client 2523[0:0] has disconnected
Mar 2 17:00:21 damnation acpid: client connected from 2523[0:0]
Mar 2 17:00:21 damnation acpid: 1 client rule loaded
Mar 3 09:54:32 damnation acpid: client 2523[0:0] has disconnected
Mar 3 09:54:32 damnation acpid: client connected from 2523[0:0]
Mar 3 09:54:32 damnation acpid: 1 client rule loaded
Mar 3 10:28:14 damnation acpid: exiting
Mar 3 10:28:14 damnation acpid: starting up
Mar 3 10:28:14 damnation acpid: 4 rules loaded
Mar 3 10:28:14 damnation acpid: waiting for events: event logging is off
Mar 3 10:28:15 damnation acpid: client connected from 2523[0:0]
Mar 3 10:28:15 damnation acpid: 1 client rule loaded
Mar 3 10:28:19 damnation acpid: client connected from 1737[82:82]
Mar 3 10:28:19 damnation acpid: 1 client rule loaded
Mar 3 10:37:44 damnation acpid: exiting
Mar 3 10:37:44 damnation acpid: starting up
Mar 3 10:37:44 damnation acpid: 4 rules loaded
Mar 3 10:37:44 damnation acpid: waiting for events: event logging is off
Mar 3 10:37:45 damnation acpid: client connected from 2523[0:0]
Mar 3 10:37:45 damnation acpid: 1 client rule loaded
Mar 3 10:37:49 damnation acpid: client connected from 1737[82:82]
Mar 3 10:37:49 damnation acpid: 1 client rule loaded
Mar 3 12:22:44 damnation acpid: exiting
Mar 3 12:23:44 damnation acpid: starting up
Mar 3 12:23:45 damnation acpid: 4 rules loaded
Mar 3 12:23:45 damnation acpid: waiting for events: event logging is off
Mar 3 12:23:46 damnation acpid: client connected from 3417[82:82]
Mar 3 12:23:46 damnation acpid: 1 client rule loaded
Mar 3 12:24:40 damnation acpid: client connected from 4287[0:0]
Mar 3 12:24:40 damnation acpid: 1 client rule loaded
Mar 3 12:24:55 damnation acpid: exiting
Mar 3 12:24:55 damnation acpid: starting up
Mar 3 12:24:55 damnation acpid: 4 rules loaded
Mar 3 12:24:55 damnation acpid: waiting for events: event logging is off
Mar 3 12:24:56 damnation acpid: client connected from 4287[0:0]
Mar 3 12:24:56 damnation acpid: 1 client rule loaded
Mar 3 12:25:00 damnation acpid: client connected from 3417[82:82]
Mar 3 12:25:00 damnation acpid: 1 client rule loaded
Mar 3 12:40:54 damnation acpid: exiting
Mar 3 12:49:47 damnation acpid: starting up
Mar 3 12:49:47 damnation acpid: 4 rules loaded
Mar 3 12:49:47 damnation acpid: waiting for events: event logging is off
Mar 3 12:49:49 damnation acpid: client connected from 3396[82:82]
Mar 3 12:49:49 damnation acpid: 1 client rule loaded
Mar 3 12:50:12 damnation acpid: client connected from 5224[0:0]
Mar 3 12:50:12 damnation acpid: 1 client rule loaded
Mar 3 12:50:59 damnation acpid: exiting
Mar 3 12:50:59 damnation acpid: starting up
Mar 3 12:50:59 damnation acpid: 4 rules loaded
Mar 3 12:50:59 damnation acpid: waiting for events: event logging is off
Mar 3 12:51:00 damnation acpid: client connected from 5224[0:0]
Mar 3 12:51:00 damnation acpid: 1 client rule loaded
Mar 3 12:51:04 damnation acpid: client connected from 3396[82:82]
Mar 3 12:51:04 damnation acpid: 1 client rule loaded
Mar 3 13:21:42 damnation acpid: exiting
Mar 3 13:21:42 damnation acpid: starting up
Mar 3 13:21:42 damnation acpid: 4 rules loaded
Mar 3 13:21:42 damnation acpid: waiting for events: event logging is off
Mar 3 13:21:43 damnation acpid: client connected from 5224[0:0]
Mar 3 13:21:43 damnation acpid: 1 client rule loaded
Mar 3 13:21:47 damnation acpid: client connected from 3396[82:82]
Mar 3 13:21:47 damnation acpid: 1 client rule loaded
Mar 3 13:22:21 damnation acpid: exiting
Mar 3 13:22:21 damnation acpid: starting up
Mar 3 13:22:21 damnation acpid: 4 rules loaded
Mar 3 13:22:21 damnation acpid: waiting for events: event logging is off
Mar 3 13:22:22 damnation acpid: client connected from 5224[0:0]
Mar 3 13:22:22 damnation acpid: 1 client rule loaded
Mar 3 13:22:26 damnation acpid: client connected from 3396[82:82]
Mar 3 13:22:26 damnation acpid: 1 client rule loaded
Mar 3 13:23:03 damnation acpid: client 5224[0:0] has disconnected
Mar 3 13:23:03 damnation acpid: client connected from 5224[0:0]
Mar 3 13:23:03 damnation acpid: 1 client rule loaded
Mar 3 13:25:00 damnation acpid: exiting
Mar 3 13:25:00 damnation acpid: starting up
Mar 3 13:25:00 damnation acpid: 4 rules loaded
Mar 3 13:25:00 damnation acpid: waiting for events: event logging is off
Mar 3 13:25:01 damnation acpid: client connected from 5224[0:0]
Mar 3 13:25:01 damnation acpid: 1 client rule loaded
Mar 3 13:25:05 damnation acpid: client connected from 3396[82:82]
Mar 3 13:25:05 damnation acpid: 1 client rule loaded
Mar 3 13:29:52 damnation acpid: client connected from 21588[1000:100]
Mar 3 13:29:52 damnation acpid: 1 client rule loaded
Mar 3 13:30:27 damnation acpid: client 21588[1000:100] has disconnected
Mar 3 13:36:15 damnation acpid: exiting
Mar 3 13:37:54 damnation acpid: starting up
Mar 3 13:37:54 damnation acpid: 4 rules loaded
Mar 3 13:37:54 damnation acpid: waiting for events: event logging is off
Mar 3 13:37:56 damnation acpid: client connected from 3419[82:82]
Mar 3 13:37:56 damnation acpid: 1 client rule loaded
Mar 3 13:38:28 damnation acpid: client connected from 4292[0:0]
Mar 3 13:38:28 damnation acpid: 1 client rule loaded
Mar 3 13:39:24 damnation acpid: exiting
Mar 3 13:39:24 damnation acpid: starting up
Mar 3 13:39:24 damnation acpid: 4 rules loaded
Mar 3 13:39:24 damnation acpid: waiting for events: event logging is off
Mar 3 13:39:25 damnation acpid: client connected from 4292[0:0]
Mar 3 13:39:25 damnation acpid: 1 client rule loaded
Mar 3 13:39:29 damnation acpid: client connected from 3419[82:82]
Mar 3 13:39:29 damnation acpid: 1 client rule loaded
Mar 3 13:44:09 damnation acpid: client connected from 4488[1000:100]
Mar 3 13:44:09 damnation acpid: 1 client rule loaded
Mar 3 13:45:42 damnation acpid: client 4488[1000:100] has disconnected
Mar 3 13:58:17 damnation acpid: exiting
Mar 3 13:58:17 damnation acpid: starting up
Mar 3 13:58:17 damnation acpid: 4 rules loaded
Mar 3 13:58:17 damnation acpid: waiting for events: event logging is off
Mar 3 13:58:18 damnation acpid: client connected from 4292[0:0]
Mar 3 13:58:18 damnation acpid: 1 client rule loaded
Mar 3 13:58:22 damnation acpid: client connected from 3419[82:82]
Mar 3 13:58:22 damnation acpid: 1 client rule loaded
(are all these "client has disconnected" messages normal?)
Last edited by Natanji (2010-03-07 11:03:54)

I don't know if it works for everyone but i have just fixed the acpi rotate for my x60t
/usr/bin/xrotate
#!/bin/sh
output=LVDS1
if [ "$XROT_OUTPUT" ]
then
output=$XROT_OUTPUT;
fi
devices="stylus eraser"
geomnbr=0
xrandr=normal
wacom=normal
if [ "$1" == "-" ] || [ "$1" == "+" ] || ! [ "$1" ];
then
operator="$1";
[ "$1" ] || operator='+';
case `xrandr --verbose | grep "^$output " | sed "s/^[^ ]* [^ ]* [^ ]* ([^(]*) $[a-z]*$.*/\1/"` in
normal) geom=0;;
left) geom=1;;
inverted) geom=2;;
right) geom=3;;
esac
let geom=${geom}${operator}1+4
let geom=${geom}%4
else
geom="$1"
fi
case $geom in
1) wacom=CCW; xrandr=left ;;
2) wacom=HALF; xrandr=inverted ;;
3) wacom=CW; xrandr=right ;;
*) wacom=NONE; xrandr=normal ;;
esac
echo "xrandr to $xrandr, xsetwacom to $wacom" >&2
if xrandr --output "$output" --rotate "$xrandr"; then
for device in $devices
do
xsetwacom set "$device" Rotate "$wacom"
done
fi
#workaround for linuxwacom bug
if [ "`xsetwacom get stylus Mode`" == '1' ]; then
for decive in $devices
do
xsetwacom set stylus CoreEvent "off"
xsetwacom set stylus Mode "off"
done
{ sleep 1;
for device in $devices
do
xsetwacom set stylus Mode "on"
xsetwacom set stylus CoreEvent "on"
done; } &
fi
/etc/acpi/thinkpad-swivel-up.sh
#!/bin/bash
XAUTHORITY=/var/lib/gdm/\:0.Xauth DISPLAY=:0.0 /usr/bin/xrotate 0
/etc/acpi/thinkpad-swivel-down.sh
#!/bin/bash
XAUTHORITY=/var/lib/gdm/\:0.Xauth DISPLAY=:0.0 /usr/bin/xrotate 1
The problem was that my acpid starts long before xorg.
System:
Thinkpad x60 tablet
xorg 1.8
acpid 1.0.10

[SOLVED] Xscreensaver-command -lock no longer working

As of yesterday afternoon (probably after the upgrade to 5.13-1), I have been unable to lock my monitor using xscreensaver. The screen fades to black, only to jump back to my desktop, and xscreensaver reporting a crash. I honestly can't see a reason from the log file, but I have little experience with programs like this. I would greatly appreciate it if someone could either confirm/let me know it's a bug that has no workaround, and I'll gladly report the bug.
Things I've tried:
Re-installing 5.13-1 (no change)
Restart of system & xscreensaver (no change in either case)
Downgrade to 5.12-2 (which works, as it did before)
The log file is as follows:
xscreensaver: 10:40:45: logging to "log.txt" at Mon May 16 10:40:45 2011
xscreensaver 5.13, copyright (c) 1991-2008 by Jamie Zawinski <[email protected]>.
xscreensaver: 10:40:45: running as lswest/lswest (1000/101)
xscreensaver: 10:40:45: in process 12688.
xscreensaver: 10:40:46: running on display ":0"
xscreensaver: 10:40:46: vendor is The X.Org Foundation, 11001000.
xscreensaver: 10:40:46: useful extensions:
xscreensaver: 10:40:46: MIT Screen-Saver (disabled at compile time)
xscreensaver: 10:40:46: Shared Memory (1.1)
xscreensaver: 10:40:46: Double-Buffering (1.0)
xscreensaver: 10:40:46: Power Management (1.1)
xscreensaver: 10:40:46: GLX
xscreensaver: 10:40:46: XF86 Video-Mode (2.2)
xscreensaver: 10:40:46: XC Misc (disabled at compile time)
xscreensaver: 10:40:46: Xinerama (1.1)
xscreensaver: 10:40:46: Resize-and-Rotate (1.3)
xscreensaver: 10:40:46: NVidia
xscreensaver: 10:40:46: NVidia GLX
xscreensaver: 10:40:46: XInput
xscreensaver: 10:40:46: screen 0 non-colormapped depths: 0 24.
xscreensaver: 10:40:46: screens in use: 1
xscreensaver: 10:40:46: 0/0: 1680x1050+0+0 (default)
xscreensaver: 10:40:46: selecting RANDR events
xscreensaver: 10:40:46: not using XInputExtension.
xscreensaver: 10:40:46: consulting /proc/interrupts for keyboard activity.
xscreensaver: 10:40:46: 0: visual 0x21 (TrueColor, depth: 24, cmap: default)
xscreensaver: 10:40:46: 0: saver window is 0x2200001.
xscreensaver: 10:40:46: selecting events on extant windows... done.
xscreensaver: 10:40:46: awaiting idleness.
xscreensaver: 10:40:54: X Error! PLEASE REPORT THIS BUG.
xscreensaver: 10:40:54: screen 0/0: 0x15d, 0x0, 0x2200001
X Error of failed request: BadMatch (invalid parameter attributes)
Major opcode of failed request: 132 (DPMS)
Minor opcode of failed request: 6 (DPMSForceLevel)
Serial number of failed request: 655
Current serial number in output stream: 656
If at all possible, please re-run xscreensaver with the command
line arguments `-sync -verbose -log log.txt', and reproduce this
bug. That will cause xscreensaver to dump a `core' file to the
current directory. Please include the stack trace from that core
file in your bug report. *DO NOT* mail the core file itself! That
won't work. A "log.txt" file will also be written. Please *do*
include the complete "log.txt" file with your bug report.
http://www.jwz.org/xscreensaver/bugs.html explains how to create
the most useful bug reports, and how to examine core files.
The more information you can provide, the better. But please
report this bug, regardless!
xscreensaver: 10:40:53: LOCK ClientMessage received; activating and locking.
xscreensaver: 10:40:53: 0: locked mode switching.
xscreensaver: 10:40:53: user is idle (ClientMessage)
xscreensaver: 10:40:53: blanking screen at Mon May 16 10:40:53 2011.
xscreensaver: 10:40:53: 0: grabbing keyboard on 0x15d... GrabSuccess.
xscreensaver: 10:40:53: 0: grabbing mouse on 0x15d... GrabSuccess.
xscreensaver: 10:40:53: fading...
xscreensaver: 10:40:54: fading done.
Last edited by lswest (2011-05-20 20:51:32)

I have the issue as well.
Edit: For now, I've downgraded as well. I need this to work for security reasons.
Last edited by darthyorik (2011-05-18 09:46:13)

[SOLVED] KWin keyboard shortcuts no longer working

My Kwin shortcuts (Maximize, tile-left, tile right) have stopped working since doing a pacman update yesterday. Any ideas on how to fix them? I am running Arch in a VirtualBox 4.3.10 VM.
EDIT: Never mind, the problem was resolved for whatever reason by today's gtk3 update.
Last edited by wiegraf (2014-05-13 02:00:43)

Ignore the permissions messages, as per http://support.apple.com/kb/TS1448
Here's the second way:
While logged into the newly created admin account, backup the bad account's folder, delete the bad account, selecting the save data option (which is stored in /Users/Deleted Users/ as a disk image), recreate the bad account using the same username/password combo, log out and back into the recreated original account. If the problem's solved, open the saved data dmg file in /Users/Deleted Users/, open the /Library/Preferences/ folder from the saved data, open the current /Users/restored account/Library/Preferences/ folder, and slowly copy plist files from the saved data folder to the current one that don't exist in it. Log out and back in to ensure there's no conflict and things still work correctly. Resolving conflicts or identifying corrupt plist files is a laborious process. Good luck.

Strange import issue .. no longer works in 2.6 or Beta 3

Strange import issue.
I use LR-2.6 everyday but have only played around with the LR-3 for a limited amount of time so the other day I decided check it out and tried to import a handful of RAW(canon) files on a SDxc-8g card via a USB card reader. I set it up to copy and convert to DNG, apply a few keywords and Metadata but when I tried it acted like it imported the first image and then froze. Card reader lights stopped blinking and just stayed on, program task bar doesn’t show any progress, not even for the first image. I then went to the folder that I was going to have the images copies to and it contained a file of the first image, but there is no indication that LR-3 even created it and it doesn’t show up in the catalog. When I tried to close out LR-3 is popped up the “in the middle of a task warning” so I just closed the program and tried it a couple more times to no avail.
So I though o well I will just open up LR-2.6 and import them from there, guess what now LR-2.6 does the exact same thing!!
I thought maybe my card reader was a POS but I was able to drag all the files to a new folder on my desktop and import them from there, nope. Tried rebooting a couple times, even opened a new catalog to test with, in both LR-2.6 and LR-3 and neither will work..
I am stumped any ideas?

Thank you for everyone's assistance
I actually figured out what the problem was, like most issues it comes back to operator error, it seem I had inadvertently chose a "rename file on import" template that I had set up to name the files based on a custom fill-in field in the Meta Data, I normally only used that template when I was exporting images that had been completely edited, so being these images were new imports that field was blank, hence it would import the first image and then do to " don't import subjected duplicates" being checked it would just stop the import process.

HP G62 Laptop fan issue, fan no longer working HELP

Basically i have a HP G60 laptop and cleaned my fan with compressed air and it stopped my laptop overheating etc etc.
HOWEVER my other half has a HP G62 laptop and her fan is LOUD and is on the verge of overheating and shutting itself down.
So i used the compressed air can to clean her fan BUT it completely stopped spinning and now i get the error message saying the fan isnt operating properly and its not advised to continue with normal use.
I can get onto windows. but the compressed air (Which EVERYONE recommends) seems to have completely either broke the fan or blown dust INTO the fan and stopped it.
After many restart attempts it came on breifly making this ticking noise as if the blades were hitting something as it spun (which was slow might i add).
MAYBE the bios has detected the fan was blocked and stopped attempting to spin??? i dont know i need help or advice before i dismantle it to try and clean the fan manually.
which i KNOW is quite fiddly for an amatuer. fans should be the easiest thing to get to not the hardest but oh well...
HELP PLEASE
This question was solved.
View Solution.

just to let you know i have fixed it, the fan seemed completely broken with no movement and its cos i spun it too fast with the compressed air or blew the clumps of dust and lint back into the fan and clogged it. either way i just got it working by taking a womens hair pin and poking it through the slot carefully and turning the blades, it got a bit difficult like there was something stopping it, but after i pushed past that point i spun it with the clip a few more times then it fired up no problems when i powered on.
thanks anyway your advice was spot on!

[SOLVED] zsh config (.zshrc) no longer working for root.

Hi,
I must've done something stupid a while ago, cause whenever I sudo -s to get some root privilages it seems .zshrc is not read.
Prompt is default and aliases don't work.
Here's my .zshrc, just in case. I'm quite sure it's okay.
# OPTIONS FOR ZSH
# PS1=$'%(!.%{\e[0;31m%}#.%{\e[0;32m%}$)>_ %{\e[0m%}' # $>_ / #>_
PS1=$'%(!.%{\e[1;31m%}%{\e[5;31m%}>>>.%{\e[1;31m%}>%{\e[1;33m%}>%{\e[1;32m%}>) %{\e[0m%}' # >>> / >>>
RPS1=$'%{\e[0;33m%}[%~]%{\e[0m%}'
# RPROMPT=$'[~]'
export PATH="/bin:/sbin:/usr/bin:/usr/sbin:/opt/mozilla/bin:$HOME/linux/bin:/opt/kde/bin:/opt/java/jre/bin:/usr/local/bin"
export EDITOR="vim"
export MANPATH="/usr/share/man:/usr/man"
export DE=kde
#export TERM=xterm-256color
# key bindings
bindkey -v
bindkey "^[[2~" overwrite-mode
bindkey "^[[3~" delete-char
bindkey "\e[7~" beginning-of-line
bindkey "\e[8~" end-of-line
bindkey "$(echotc kl)" backward-char
bindkey "\E[A" up-line-or-search
bindkey "\E[B" down-line-or-search
bindkey '^R' history-incremental-search-backward
bindkey -M vicmd 'k' up-line-or-search
bindkey -M vicmd 'j' down-line-or-search
HISTFILE=~/.zshhistory
HISTSIZE=50000
SAVEHIST=50000
# aliases
alias ..='cd ..'
alias cl='clear'
alias ls='ls --color=auto'
alias lsl='ls -hl --color=auto'
alias rm='rm -v'
alias pg='pgrep -lf'
alias ka='killall -s 9'
alias sus='sudo -s'
alias hdtemp='sudo hddtemp /dev/sda'
alias du="du -h"
alias df="df -h"
alias freq="cpufreq-info | grep decide"
alias mpdkill="sudo mpd --kill && killall -s 9 mpdscribble"
alias sudo="sudo "
alias nc="ncmpcpp"
alias cmatrix="cmatrix -abu2"
alias x="startx"
alias thinkpad-smapi="thinkpad-smapi -b 0"
alias relap="sudo /etc/rc.d/laptop-mode restart"
alias rewlan="sudo ifconfig wlan0 {down,up}"
alias rentpd="sudo /etc/rc.d/openntpd restart"
alias resamba="sudo /etc/rc.d/samba restart"
alias recups="sudo /etc/rc.d/cups restart"
alias reblue="sudo /etc/rc.d/bluetooth restart"
alias fancool="/etc/rc.d/thinkfan stop && echo level 7 > /proc/acpi/ibm/fan"
alias fanstart="sudo /etc/rc.d/thinkfan start"
# functions
fs() { find $1 -iname '*'$2'*'; }
gcurses() { gcc $1 -o $(cut -d . -f 1 $1) -lncurses;}
ranger () {
command ranger --fail-unless-cd $@ &&
cd "$(grep \^\' ~/.ranger/bookmarks | cut -b3-)"
# completion
autoload -U compinit
compinit
# correction
setopt correctall
# prompt
# autoload -U promptinit
# promptinit
# prompt redhat
# options
setopt hist_ignore_all_dups
setopt hist_ignore_space
setopt nohup # don't kill bg jobs when tty quits
setopt nocheckjobs # don't complain about background jobs on exit
#Some functions, like _apt and _dpkg, are very slow. You can use a cache in order to proxy the list of results (like the list of available debian packages) Use a cache:
zstyle ':completion:*' use-cache on
zstyle ':completion:*' cache-path ~/.zsh/cache
#Prevent CVS files/directories from being completed:
zstyle ':completion:*:(all-|)files' ignored-patterns '(|*/)CVS'
#Ignore completion functions for commands you don't have:
zstyle ':completion:*:functions' ignored-patterns '_*'
zstyle ':completion:*:cd:*' ignored-patterns '(*/)#CVS'
zstyle ':completion:*:processes-names' command 'ps -e -o comm='
Last edited by vi3dr0 (2010-09-19 15:10:41)

I think this was a pushed /etc/sudoers file that pacdiffviewer prompts you to replace with, maybe a month ago? If you were like me, you probably only added yourself being able to sudo. I don't have the old version, but I don't remember requiring the code I gave you... maybe they've changed something necessitating the new file. Anyway, happy times, my prompt turns red when I 'sudo -s'

[SOLVED] USB Sound card no longer working

I have used a Focusrite Scarlett 2i2, a USB audio interface, as my default sound card for the last two months or so. Its output comprises two RCA jacks. I have a cable that is two RCA male leads on one end and an 1/8" on the other. I use this cable all over the house, so I unplug it often. The USB device remains connected. Last night, while plugging the cable back into the device, I jostled the USB and the device lost power momentarily. Since then, ALSA has not been able to "see" the device. The device is, and always has been, plugged into a D-Link USB hub, which goes into the computer.
I did pacman -Syu and rebooted to no avail.
uname -r
3.15.1-1-ARCH
lsusb | grep -i focusrite
Bus 001 Device 005: ID 1235:8006 Focusrite-Novation Focusrite Scarlett 2i2
modinfo snd_usb_audio
http://pastebin.com/CEMr6Gif
cat /etc/modprobe.d/alsa-base.conf
#options snd slots=snd_usb_audio,snd_hda_intel
options snd_hda_intel index=-2
options snd_usb_audio index=0
The first line I recently commented out as an experiment. If this line is left in, ALSA attempts to use snd_usb_audio and when I run alsamixer it complains that it can't find the device. If this line is commented out, ALSA ends up using the on-board sound. Particularly, it uses 'HDA ATI HDMI'. There are two choices: HDA ATI HDMI and HDA ATI SB. When I was using the on-board sound, I was using HDA ATI SB.
cat /proc/asound/modules
0 snd_hda_intel
1 snd_hda_intel
lspci -nn | grep -i audio
00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) [1002:4383]
01:05.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] RS880 HDMI Audio [Radeon HD 4200 Series] [1002:970f]
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: SB [HDA ATI SB], device 0: ALC889A Analog [ALC889A Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: SB [HDA ATI SB], device 1: ALC889A Digital [ALC889A Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
lsmod | grep '^snd'
snd_hda_codec_realtek 48535 1
snd_hda_codec_generic 50352 1 snd_hda_codec_realtek
snd_hda_codec_hdmi 36976 1
snd_hda_intel 18830 0
snd_hda_controller 19667 1 snd_hda_intel
snd_hda_codec 91154 5 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
snd_hwdep 5162 1 snd_hda_codec
snd_pcm 68932 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 15678 1 snd_pcm
snd 46421 8 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
ls -l /dev/snd
total 0
drwxr-xr-x 2 root root 80 Jun 26 10:13 by-path
crw-rw----+ 1 root audio 116, 2 Jun 26 10:13 controlC0
crw-rw----+ 1 root audio 116, 5 Jun 26 10:13 controlC1
crw-rw----+ 1 root audio 116, 4 Jun 26 10:13 hwC0D0
crw-rw----+ 1 root audio 116, 11 Jun 26 10:13 hwC1D0
crw-rw----+ 1 root audio 116, 3 Jun 26 10:13 pcmC0D3p
crw-rw----+ 1 root audio 116, 7 Jun 26 10:13 pcmC1D0c
crw-rw----+ 1 root audio 116, 6 Jun 26 10:13 pcmC1D0p
crw-rw----+ 1 root audio 116, 9 Jun 26 10:13 pcmC1D1c
crw-rw----+ 1 root audio 116, 8 Jun 26 10:13 pcmC1D1p
crw-rw----+ 1 root audio 116, 10 Jun 26 10:13 pcmC1D2c
crw-rw----+ 1 root audio 116, 1 Jun 26 10:13 seq
crw-rw----+ 1 root audio 116, 33 Jun 26 10:13 timer
All this information was collected while the device has been connected to the computer. Any help is greatly appreciated. Thanks!
Last edited by gluelogic (2014-07-01 21:36:19)

emeres wrote:You only ruled out hardware failure on the device side.
This is painfully true. This morning, I realized I didn't even check the D-Link. The LEDs on the interface were lit up from the USB connection, but the AC adapter was faulty. I replaced that, restored my original configuration by removing the # from the first line of my alsa-base.conf, and now everything is working again. The D-Link was simply unable to provide the device with enough power to operate.

After updating the iOS from 4.2.1 to 4.3.3 the WLAN connection to a Win7 Hotspot (Connectify) is no longer working in the sence that UPnP Apps like PlugPlayer can connect to a Media Server (Twonky) on the Win7 PC in a stable way. What to do?

I created a backup of the iPod in iTunes before updating to iOS 4.33 but after the update I can not restore. The backup is no longer shown in iTunes. I think iOS 4.3.3 has some differences in handling WLAN due to the Hot Spot capability for the iPone 4 which might cause these problems.
Please help. The only use of my iPod touch is to remote control my media network. And exactly that is no longer working the way it was before the update!
Best Regards,
Gerd

Now this has two direct effects - firstly it has increased the 3g usage for data and secondly it causes 'blips' with the ability to connect to previously working wifi connections.
Landshark2007 wrote:
We have identified that 4.2.1 in the iPhone 4 has WPA2 key length issues.
Although I have seen posts about the problem WPA2 key length problem, I am using an iPhone 4 with iOS 4.2.1 and have no problems connecting to my WiFi that uses WPA2 AES with a key that is over 20 characters.
Landshark2007 wrote:
There is also one other school of thought that we have which is to do with the increased battery performance on the iPhones. It looks as though the iPhone drops WiFi when it goes to sleep (ie: when it is turned off in normal mode).
An iPhone will maintain a WiFi connection when in sleep mode if it is connected to a power source.
I have no doubt that many users are experiencing problems with their iPhones. I just feel lucky that I haven't experienced any big issues with mine.

Ios 6 orientation doesn't work and boot time increases. How to solve these issues for dummy? I don't understand code and strings suggested by others.

I just upgraded from ios 5 to ios 6 on my ipad2. Now orientation doesn't work properly. Boot time increase, it takes longer time to boot. Is there any configuration to solve these issues? I can't understand the explanation with code and strings found on google to solve the orientation issue. Any easy configuration for dummy ?

It supports well for ios 5. I couldn't remember (5.x.x) exactly but I always keeps update for ios5 and the abnormality starts when I upgraded to ios 6.

[SOLVED: HW ISSUE] WLAN no longer works (Zotac IQ01 / r8169 / iwlwifi)

Similar Messages

Maybe you are looking for