(Solved) [Intel HDA] Headphones not detected

Hi there,
I'm having an annoying issue since I've installed (and re-installed) Arch on my netbook.
Everything's alright (except Gnash, but I'll google that later), the internal speakers work perfectly but when I put my headphones or my speakers (ext.) the internal speakers are "muted-off" (so the jack is detected, right?) but nothing's coming out from my headphones/speakers.
Here's my aplay -l out :
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: CONEXANT Analog [CONEXANT Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: Conexant Digital [Conexant Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
And here is my amixer output:
Simple mixer control 'Master',0
Capabilities: pvolume pswitch pswitch-joined
Playback channels: Front Left - Front Right
Limits: Playback 0 - 65536
Mono:
Front Left: Playback 65536 [100%] [on]
Front Right: Playback 65536 [100%] [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch cswitch-joined
Capture channels: Front Left - Front Right
Limits: Capture 0 - 65536
Front Left: Capture 27636 [42%] [off]
Front Right: Capture 27636 [42%] [off]
and a lspci | grep Audio output:
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02)
My headphones are plugged-in since I booted.
Another problem is that when I'm launching alsamixer there's only the master (Card: PulseAudio - Chip: PulseAudio). So, I make F6 > "1 HDA Intel" and I have other channels :
Master (100 & unmuted) - PCM (100 & unmunted) - Mic (0 & muted) - S/PDIF (muted) - S/PDIF Default PCM (unmuted) - Beep (86 & muted) - Internal Mic (0 & muted) -- (Card: HDA Intel - Chip: Conexant CX20549 (Venice))
This is strange because on my former installation of Arch (on the same PC) the "default" alsamixer had exactly the same channels and the "Master only" didn't 'exists'. (But I had the same problems).
I tried a bunch of solutions I found but none worked.
alsa-utils alsa-plugins & alsa-oss are installed (base-devel too if it can help).
I'm using SLiM & Cinnamon and had the same issue with LXDM & LXDE (same computer).
So if somebody could gave me a little bit of his light it'll be much appreciated!
Thank you, Flaco
*Edit: Since I've rebooted with the headphones plugged-in the internal speakers don't work neither... but it may be something else; I tried a lot of solutions so maybe there's conflict between some files and/or process...
**Edit: Internal speakers issue solved. I might have touched some stuffs on pavucontrol before... anyway, the headphones are still a problem...
***Edit: I've booted (on a live usb) on Lubuntu to see what's happening and... still no sound. The jack input might be broken; I'll open my computer to see what's happening and to repair (or not) it.
Last edited by Flaco (2013-07-04 00:19:57)

bump :x

Similar Messages

[SOLVED] Verbatim USB headphones not detected

I did use this head set once when I bought them in september and they showed up in gnome's pulseaudio-mixer-applet. I can't recall installing anything, just plugged them in...
However when I tried today nothing appeared, and dmesg gives med this:
usb 1-5.2: new full speed USB device using ehci_hcd and address 4
usb 1-5.2: device descriptor read/64, error -32
usb 1-5.2: device descriptor read/64, error -32
usb 1-5.2: new full speed USB device using ehci_hcd and address 5
usb 1-5.2: device descriptor read/64, error -32
usb 1-5.2: device descriptor read/64, error -32
usb 1-5.2: new full speed USB device using ehci_hcd and address 6
usb 1-5.2: device not accepting address 6, error -32
usb 1-5.2: new full speed USB device using ehci_hcd and address 7
usb 1-5.2: device not accepting address 7, error -32
Does anyone know if something is changed in pulseaudio or kernel or anything?
Last edited by toffyrn (2010-10-25 12:19:27)

Ah. Looks like hardware fault. Windows presents it as "not recognized".
Strange thing is, i used it playing Fallout this morning. Thats why I assumed it was a linux problem...

SBH9150 philips bluetooth headphone not detected in macbook pro retina 13"

I just purchased an SBH9150 philips bluetooth headphone. But my macbook pro retina 13" could not detect it. Anybody can help? It is perfectly working with my iphone 5.

Unpair it from your phone and then try pairing it to your Mac.
Does the Mac see any BT devices like KB or mouse?

SOLVED Hp TrueVision HD " not detecting " =Solution

Hp TrueVision HD " not detecting " Solution
===============================
To the all guys have a problem like this
{{ your system can not detect the webcam or the name is not in the device list }}
There is a cable or socket which is connected to the webcam so the only reason cause this problem is about that socket
Now just open the fram of your laptop screen u will see a small socket right hand side of camera just make sure it is connected truely or u can make it totally disconnect then connect.
You can also check this video
http://www.youtube.com/watch?v=jOpS6GD0hZo
now u easily fixed it
good luck

Hi @MysteryBacon ,
Welcome to the HP Forums!
It is a great place to find answers and suggestions!.
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
I understand that you are having an issue with the WebCam and recording.
To be of assistance I need some more information.
What is your exact model of HP ENVY 14 SPECTRE do you have?
What Operating System are you running?
What are you trying to record?
Have you ran the HP Support Assistant to aid with any applicable HP updates?
Have you tried running MS Fix It to assist in overcoming difficulties?
Regards
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

[Solved]StlinkV2-1 kernel not detecting the device

I have a stm32 board which have stlink with it. I installed the stlink and all the necessary udev rules are there. If enumerated properly it will create a serial device /dev/ttyACMx and will also show a fat partition.
When the board is connected and i restart the computer it works fine, serial port is there. But when the computer is running, i remove and insert again the usb cable it is not recognised. I get the following error in dmesg
[ 355.618200] usb 3-7: new full-speed USB device number 5 using xhci_hcd
[ 355.792759] usb 3-7: ep 0x84 - rounding interval to 1024 microframes, ep desc says 2040 microframes
[ 355.793280] usb 3-7: can't set config #1, error -71
but if i reset all the usb ports using
# reseting USB2 ports
for i in $(ls /sys/bus/pci/drivers/ehci_hcd/|grep :)
do echo $i >/sys/bus/pci/drivers/ehci_hcd/unbind
echo $i >/sys/bus/pci/drivers/ehci_hcd/bind
done
# reseting USB3 ports (if there none you'll get errors)
for i in $(ls /sys/bus/pci/drivers/xhci_hcd/|grep :)
do echo $i >/sys/bus/pci/drivers/xhci_hcd/unbind
echo $i >/sys/bus/pci/drivers/xhci_hcd/bind
done
It works fine. I have H97 MSI gamer 3 board.
lsusb
Bus 002 Device 002: ID 8087:8001 Intel Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:8009 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 005: ID 0483:374b STMicroelectronics
Bus 003 Device 003: ID 04d9:1203 Holtek Semiconductor, Inc. Keyboard
Bus 003 Device 002: ID 15d9:0a4d Trust International B.V. Optical Mouse
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
lspci
00:00.0 Host bridge: Intel Corporation 4th Gen Core Processor DRAM Controller (rev 06)
00:02.0 VGA compatible controller: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor Integrated Graphics Controller (rev 06)
00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06)
00:14.0 USB controller: Intel Corporation 9 Series Chipset Family USB xHCI Controller
00:16.0 Communication controller: Intel Corporation 9 Series Chipset Family ME Interface #1
00:1a.0 USB controller: Intel Corporation 9 Series Chipset Family USB EHCI Controller #2
00:1b.0 Audio device: Intel Corporation 9 Series Chipset Family HD Audio Controller
00:1c.0 PCI bridge: Intel Corporation 9 Series Chipset Family PCI Express Root Port 1 (rev d0)
00:1c.2 PCI bridge: Intel Corporation 9 Series Chipset Family PCI Express Root Port 3 (rev d0)
00:1c.3 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d0)
00:1d.0 USB controller: Intel Corporation 9 Series Chipset Family USB EHCI Controller #1
00:1f.0 ISA bridge: Intel Corporation 9 Series Chipset Family H97 Controller
00:1f.2 SATA controller: Intel Corporation 9 Series Chipset Family SATA Controller [AHCI Mode]
00:1f.3 SMBus: Intel Corporation 9 Series Chipset Family SMBus Controller
02:00.0 Ethernet controller: Qualcomm Atheros Killer E220x Gigabit Ethernet Controller (rev 13)
03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03)
04:02.0 Network controller: Ralink corp. RT5360 Wireless 802.11n 1T/1R
dmesg
[ 4.951736] [drm] Replacing VGA console driver
[ 4.955829] intel_rapl: Found RAPL domain package
[ 4.955832] intel_rapl: Found RAPL domain core
[ 4.955833] intel_rapl: Found RAPL domain uncore
[ 4.955835] intel_rapl: Found RAPL domain dram
[ 4.968948] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 4.968949] [drm] Driver supports precise vblank timestamp query.
[ 4.968996] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 4.983385] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.983659] acpi device:16: registered as cooling_device14
[ 4.983713] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input19
[ 4.983788] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[ 4.983789] [drm] Initialized i915 1.6.0 20150130 for 0000:00:02.0 on minor 0
[ 5.009305] fbcon: inteldrmfb (fb0) is primary device
[ 5.049339] scsi 6:0:0:0: Direct-Access MBED microcontroller 1.0 PQ: 0 ANSI: 2
[ 5.049833] sd 6:0:0:0: [sdb] 1056 512-byte logical blocks: (540 kB/528 KiB)
[ 5.050010] sd 6:0:0:0: [sdb] Write Protect is off
[ 5.050011] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 5.050151] sd 6:0:0:0: [sdb] No Caching mode page found
[ 5.050152] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 5.056156] sdb:
[ 5.056842] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 5.068788] Console: switching to colour frame buffer device 240x67
[ 5.071377] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 5.071378] i915 0000:00:02.0: registered panic notifier
[ 5.119387] Adding 2097148k swap on /dev/sda5. Priority:-1 extents:1 across:2097148k FS
[ 5.168352] fuse init (API version 7.23)
[ 5.195473] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input20
[ 5.195512] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input21
[ 5.195571] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input22
[ 5.208053] FAT-fs (sda2): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 5.242831] systemd-journald[177]: Received request to flush runtime journal from PID 1
[ 7.509192] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[ 7.519645] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
[ 8.951338] wlp4s2: authenticate with e8:de:27:f4:9f:e8
[ 8.959044] wlp4s2: send auth to e8:de:27:f4:9f:e8 (try 1/3)
[ 8.960912] wlp4s2: authenticated
[ 8.962265] wlp4s2: associate with e8:de:27:f4:9f:e8 (try 1/3)
[ 8.966097] wlp4s2: RX AssocResp from e8:de:27:f4:9f:e8 (capab=0x431 status=0 aid=2)
[ 8.966201] wlp4s2: associated
[ 8.966235] cfg80211: Calling CRDA to update world regulatory domain
[ 85.421055] usb 3-7: USB disconnect, device number 4
[ 89.268764] usb 3-7: new full-speed USB device number 5 using xhci_hcd
[ 89.443392] usb 3-7: ep 0x84 - rounding interval to 1024 microframes, ep desc says 2040 microframes
[ 89.443983] usb 3-7: can't set config #1, error -71
[ 328.016009] xhci_hcd 0000:00:14.0: remove, state 4
[ 328.016014] usb usb4: USB disconnect, device number 1
[ 328.016145] xhci_hcd 0000:00:14.0: USB bus 4 deregistered
[ 328.016149] xhci_hcd 0000:00:14.0: remove, state 1
[ 328.016152] usb usb3: USB disconnect, device number 1
[ 328.016153] usb 3-3: USB disconnect, device number 2
[ 328.051877] usb 3-4: USB disconnect, device number 3
[ 328.242927] usb 3-7: USB disconnect, device number 5
[ 328.243395] xhci_hcd 0000:00:14.0: USB bus 3 deregistered
[ 328.243647] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 328.243651] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 328.341680] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
[ 328.341697] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 328.342018] hub 3-0:1.0: USB hub found
[ 328.342043] hub 3-0:1.0: 14 ports detected
[ 328.366699] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 328.366714] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[ 328.366981] hub 4-0:1.0: USB hub found
[ 328.366994] hub 4-0:1.0: 6 ports detected
[ 328.704933] usb 3-3: new low-speed USB device number 2 using xhci_hcd
[ 328.881338] usb 3-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 328.883404] input: USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3:1.0/0003:15D9:0A4D.0004/input/input23
[ 328.883642] hid-generic 0003:15D9:0A4D.0004: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:14.0-3/input0
[ 329.041600] usb 3-4: new low-speed USB device number 3 using xhci_hcd
[ 329.226073] usb 3-4: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 329.226076] usb 3-4: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 329.234694] input: HID 04d9:1203 as /devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/0003:04D9:1203.0005/input/input24
[ 329.285004] hid-generic 0003:04D9:1203.0005: input,hidraw1: USB HID v1.11 Keyboard [HID 04d9:1203] on usb-0000:00:14.0-4/input0
[ 329.298893] input: HID 04d9:1203 as /devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.1/0003:04D9:1203.0006/input/input25
[ 329.351641] hid-generic 0003:04D9:1203.0006: input,hidraw2: USB HID v1.11 Device [HID 04d9:1203] on usb-0000:00:14.0-4/input1
[ 329.511596] usb 3-7: new full-speed USB device number 4 using xhci_hcd
[ 329.686380] usb 3-7: ep 0x84 - rounding interval to 1024 microframes, ep desc says 2040 microframes
[ 329.686966] usb-storage 3-7:1.1: USB Mass Storage device detected
[ 329.687165] scsi host7: usb-storage 3-7:1.1
[ 329.687382] cdc_acm 3-7:1.2: ttyACM0: USB ACM device
[ 330.688552] scsi 7:0:0:0: Direct-Access MBED microcontroller 1.0 PQ: 0 ANSI: 2
[ 330.688935] sd 7:0:0:0: [sdb] 1056 512-byte logical blocks: (540 kB/528 KiB)
[ 330.689089] sd 7:0:0:0: [sdb] Write Protect is off
[ 330.689091] sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 330.689284] sd 7:0:0:0: [sdb] No Caching mode page found
[ 330.689286] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 330.695324] sdb:
[ 330.696110] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 352.926977] usb 3-7: USB disconnect, device number 4
[ 355.618200] usb 3-7: new full-speed USB device number 5 using xhci_hcd
[ 355.792759] usb 3-7: ep 0x84 - rounding interval to 1024 microframes, ep desc says 2040 microframes
[ 355.793280] usb 3-7: can't set config #1, error -71
I want that whenever i insert the stlink board it should enumerate properly and create serial port.
Last edited by sanjuchopra (2015-05-30 14:44:25)

I got it working. Actually the cable was faulty. I tried with other cable and it worked fine. But strange thing is that after usb reset old cable works fine.

Headphones Not Detected

Hi,
I recently purchased this laptop and the headphones never were detected. I have updated my RealTek audio drivers. I have tried multiple headphones and they are working on other computers.
When I plug in the headphones, the headphones do not work and the sound still plays from the speakers. The headphones are not listed in Playback devices. Only the RealTek spaeakers are listed.
My BIOS is F.09 from 08/04/2014
Producct Name: HP Envy 15 Notebook
Product Number: G0T55AV
Drivers: Up to Date (RealTek Drivers)
Thank you for helping. I am thinking of returning this laptop I just purchased soon if I can't get this fixed.
Sincerely,
Ben

Hi @Butterback ,
Thank you for your query.
I grasps that when you connect your headphones the sound comes out of the speakers and not the headphones.
Please try the step in this document to overcome this difficulty. Troubleshooting Sound Problems with External Speakers and Headsets in Windows 7.
If the issue should remain please contact HP support for further assistance. As this is a new notebook you want to know everything is working correctly.
Please call our technical support at 800 474 6836. If you live outside the US/Canada Region, please click the link below to get a support number for your region.
World Wide Phone Support
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

[SOLVED]Intel HDA HDMI Keeps Coming Back From The Dead Like a Vampire

I have an Asus H87M-Pro mobo with a E3-1265L v3 Intel CPU. This CPU does my audio and video, but the problem is I haven't had audio since I installed this mobo. Dead silent.
I believe the problem must be that HDMI audio is siezing card0, which I infer is the default sound slot, but blacklisting the modules hasn't worked:
blacklist snd-hda-intel-hdmi
blacklist snd-hda-codec-hdmi
... and setting those modules to never, never take card0 hasn't worked:
options snd-hda-intel-hdmi index=-2
options snd-hda-codec-hdmi index=-2
alsamixer always comes up first with
Card: PulseAudio
Chip: PulseAudio
I can <f6> and choose HDA Intel PCH and it's not muted, but that doesn't get me audio.
With no settings in /etc/modprobe.d/blacklist.conf I get:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDA Intel HDMI], device 3: ID 2807 Digital [ID 2807 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
$ aplay -L
default
Playback/recording through the PulseAudio sound server
hdmi:CARD=HDMI,DEV=0
HDA Intel HDMI, ID 2807 Digital
HDMI Audio Output
sysdefault:CARD=PCH
HDA Intel PCH, ALC892 Analog
Default Audio Device
front:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
Front speakers
surround40:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Digital
IEC958 (S/PDIF) Digital Audio Output
With my above settings in /etc/modprobe.d/blacklist.conf, plus:
options snd-hda-intel id=PCH,HDMI index=1,0
... I do find a change:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: HDMI [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: PCH [HDA Intel HDMI], device 3: ID 2807 Digital [ID 2807 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
... but the machine is still mute. -How- can it be HDMI -and- PCH?!
I have never had a problem with audio before. Anyone know what's going on here?
Last edited by Quantum (2014-04-16 18:03:02)

emeres wrote:
options snd-hda-intel id=PCH,HDMI index=1,0
The first index value (1) corresponds to first id (PCH) and since sound cards are counted from 0, this sets HDMI as primary. This should become pretty clear following the example on wiki.
Oh it's clear when you have different sound cards, as with their example of the MIA. But what's not clear at all within the Intel driver, is the relation between "index value" (an utterly abstract term unconnected with anything substantive), and ID. I infer that the IDs in this case are PCH and HDMI. But HDMI has two possibilities, analog and digital, as does PCH. How can HDMI have an analog function? And is PCH my goal? And what does PCH mean anyway? Why does everything have HDMI in the name? Where does Pulse fit in all this, since alsamixer considers it the default? And why is the module named snd-hda-intel-hdmi.ko yet when it's loaded it's called snd_hda_intel_hdmi? And which should I use in blacklist.conf? And why is there a snd-hda-intel-hdmi.ko and snd-hda-codec-hdmi.ko? And which should I use in blacklist.conf for options?
See none of this is explained in the wiki, and yet is fundamental to understanding how to set this up. Whoever wrote the wiki already knows all this and assumes the reader does too, which is a common failing of tech writers. With huge gaps in the information, I can't begin to synthesize a solution. Maybe fundamentals aren't important to the kids these days. They will find out soon enough though.
emeres wrote:
options snd_hda_intel enable=1,0
This is ambiguous, since, like I previously stated snd-hda-intel is used by both cards. Again the link to wiki where it is explained step by step how to determine vid and pid and use it with options. Vid and pid are used to determine a specific card and so specific options can be set for a specific card. They can be used with both suggestions. Yes there are very unlikely scenarios, where it might cause more trouble than good.
I think you mean this:
blacklist.conf:
options snd-hda-intel id=PCH,HDMI index=0,1
options snd-hda-intel-hdmi index=-2
options snd-hda-codec-hdmi index=-2
# aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel HDMI], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
Unfortunately it doesn't work. Notice that now everything has HDMI in the string... ridiculous.
By vid/pid, I think you mean this:
# lspci -nn |grep -i audio
00:03.0 Audio device [0403]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller [8086:0c0c] (rev 06)
00:1b.0 Audio device [0403]: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller [8086:8c20] (rev 04)
05:00.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23885 PCI Video and Audio Decoder [14f1:8852] (rev 03)
Where's HDMI? Where's analog? Guessing that "4th Gen Core Processor HD Audio Controller" might be HDMI:
blacklist.conf:
# PCH
options snd-hda-intel index=0 model=auto vid=8086 pid=8c20
# HDMI
options snd-hda-intel index=1 model=auto vid=8086 pid=0c0c
# Hauppauge
options snd-hda-intel index=2 model=auto vid=14f1 pid=8852
alsaplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: HDMI [HDA Intel HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: HDMI [HDA Intel HDMI], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
Now thankfully I do now have audio for the first time on this mobo.
But HDMI is now 3rd? And there is no Hauppauge? Can anything be done about that?
Last edited by Quantum (2014-04-16 18:01:57)

[SOLVED] Intel driver is not loading.

Hello,
I just got a new laptop and finally put Arch on it. I have to use "nomodeset" to see anything (Putting the intel_agp and i915 modules in the initramfs does not work, nor does the SVIDEO option.) and I installed xorg and xf86-video-intel, and ran startx, and it failed to run.
Below are my Xorg.log.0 and lspci -k outputs.
Xorg.log.0
[ 1307.124]
X.Org X Server 1.14.1
Release Date: 2013-04-17
[ 1307.129] X Protocol Version 11, Revision 0
[ 1307.130] Build Operating System: Linux 3.8.7-1-ARCH x86_64
[ 1307.131] Current Operating System: Linux spike 3.8.8-2-ARCH #1 SMP PREEMPT Tue Apr 23 10:28:14 CEST 2013 x86_64
[ 1307.131] Kernel command line: root=/dev/sda5 ro rootfstype=ext4 systemd.unit=graphical.target nomodeset initrd=EFI\arch\initramfs-arch.img
[ 1307.133] Build Date: 17 April 2013 02:37:06PM
[ 1307.134]
[ 1307.136] Current version of pixman: 0.28.2
[ 1307.138] Before reporting problems, check [url]http://wiki.x.org[/url]
to make sure that you have the latest version.
[ 1307.138] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 1307.142] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Apr 25 17:51:54 2013
[ 1307.143] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 1307.143] (==) No Layout section. Using the first Screen section.
[ 1307.143] (==) No screen section available. Using defaults.
[ 1307.143] (**) |-->Screen "Default Screen Section" (0)
[ 1307.143] (**) | |-->Monitor "<default monitor>"
[ 1307.144] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 1307.144] (==) Automatically adding devices
[ 1307.144] (==) Automatically enabling devices
[ 1307.144] (==) Automatically adding GPU devices
[ 1307.144] (WW) The directory "/usr/share/fonts/TTF/" does not exist.
[ 1307.144] Entry deleted from font path.
[ 1307.144] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 1307.144] Entry deleted from font path.
[ 1307.144] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 1307.144] Entry deleted from font path.
[ 1307.144] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 1307.144] Entry deleted from font path.
[ 1307.144] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 1307.144] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 1307.144] Entry deleted from font path.
[ 1307.144] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 1307.144] (==) FontPath set to:
/usr/share/fonts/misc/
[ 1307.144] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 1307.144] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 1307.144] (II) Loader magic: 0x7fcc20
[ 1307.144] (II) Module ABI versions:
[ 1307.144] X.Org ANSI C Emulation: 0.4
[ 1307.144] X.Org Video Driver: 14.1
[ 1307.144] X.Org XInput driver : 19.1
[ 1307.144] X.Org Server Extension : 7.0
[ 1307.145] (--) PCI:*(0:0:2:0) 8086:0116:103c:1854 rev 9, Mem @ 0xc2000000/4194304, 0xb0000000/268435456, I/O @ 0x00004000/64
[ 1307.146] Initializing built-in extension Generic Event Extension
[ 1307.147] Initializing built-in extension SHAPE
[ 1307.148] Initializing built-in extension MIT-SHM
[ 1307.149] Initializing built-in extension XInputExtension
[ 1307.150] Initializing built-in extension XTEST
[ 1307.151] Initializing built-in extension BIG-REQUESTS
[ 1307.152] Initializing built-in extension SYNC
[ 1307.153] Initializing built-in extension XKEYBOARD
[ 1307.154] Initializing built-in extension XC-MISC
[ 1307.155] Initializing built-in extension SECURITY
[ 1307.156] Initializing built-in extension XINERAMA
[ 1307.157] Initializing built-in extension XFIXES
[ 1307.158] Initializing built-in extension RENDER
[ 1307.159] Initializing built-in extension RANDR
[ 1307.159] Initializing built-in extension COMPOSITE
[ 1307.160] Initializing built-in extension DAMAGE
[ 1307.161] Initializing built-in extension MIT-SCREEN-SAVER
[ 1307.162] Initializing built-in extension DOUBLE-BUFFER
[ 1307.163] Initializing built-in extension RECORD
[ 1307.163] Initializing built-in extension DPMS
[ 1307.164] Initializing built-in extension X-Resource
[ 1307.165] Initializing built-in extension XVideo
[ 1307.165] Initializing built-in extension XVideo-MotionCompensation
[ 1307.166] Initializing built-in extension XFree86-VidModeExtension
[ 1307.167] Initializing built-in extension XFree86-DGA
[ 1307.167] Initializing built-in extension XFree86-DRI
[ 1307.168] Initializing built-in extension DRI2
[ 1307.168] (II) LoadModule: "glx"
[ 1307.168] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 1307.168] (II) Module glx: vendor="X.Org Foundation"
[ 1307.168] compiled for 1.14.1, module version = 1.0.0
[ 1307.168] ABI class: X.Org Server Extension, version 7.0
[ 1307.168] (==) AIGLX enabled
[ 1307.169] Loading extension GLX
[ 1307.169] (==) Matched intel as autoconfigured driver 0
[ 1307.169] (==) Matched vesa as autoconfigured driver 1
[ 1307.169] (==) Matched modesetting as autoconfigured driver 2
[ 1307.169] (==) Matched fbdev as autoconfigured driver 3
[ 1307.169] (==) Assigned the driver to the xf86ConfigLayout
[ 1307.169] (II) LoadModule: "intel"
[ 1307.169] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 1307.169] (II) Module intel: vendor="X.Org Foundation"
[ 1307.169] compiled for 1.14.0, module version = 2.21.6
[ 1307.169] Module class: X.Org Video Driver
[ 1307.169] ABI class: X.Org Video Driver, version 14.1
[ 1307.169] (II) LoadModule: "vesa"
[ 1307.170] (WW) Warning, couldn't open module vesa
[ 1307.170] (II) UnloadModule: "vesa"
[ 1307.170] (II) Unloading vesa
[ 1307.170] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 1307.170] (II) LoadModule: "modesetting"
[ 1307.170] (WW) Warning, couldn't open module modesetting
[ 1307.170] (II) UnloadModule: "modesetting"
[ 1307.170] (II) Unloading modesetting
[ 1307.170] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 1307.170] (II) LoadModule: "fbdev"
[ 1307.170] (WW) Warning, couldn't open module fbdev
[ 1307.170] (II) UnloadModule: "fbdev"
[ 1307.170] (II) Unloading fbdev
[ 1307.170] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 1307.170] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2),
Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2),
Haswell Server (GT2+), Haswell SDV Desktop (GT1),
Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+),
Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),
Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1),
Haswell SDV Server (GT2), Haswell SDV Server (GT2+),
Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),
Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1),
Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+),
Haswell ULT Server (GT1), Haswell ULT Server (GT2),
Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1),
Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+),
Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2),
Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1),
Haswell CRW Server (GT2), Haswell CRW Server (GT2+),
ValleyView PO board
[ 1307.170] (++) using VT number 1
[ 1307.172] (EE) No devices detected.
[ 1307.172]
Fatal server error:
[ 1307.172] no screens found
[ 1307.172] (EE)
Please consult the The X.Org Foundation support
at [url]http://wiki.x.org[/url]
for help.
[ 1307.172] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 1307.172] (EE)
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
Subsystem: Hewlett-Packard Company Device 1854
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
Subsystem: Hewlett-Packard Company Device 1854
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
Subsystem: Hewlett-Packard Company Device 1854
Kernel driver in use: mei
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
Subsystem: Hewlett-Packard Company Device 1854
Kernel driver in use: ehci-pci
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
Subsystem: Hewlett-Packard Company Device 1854
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 (rev c4)
Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 4 (rev c4)
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
Subsystem: Hewlett-Packard Company Device 1854
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge: Intel Corporation HM75 Express Chipset LPC Controller (rev 04)
Subsystem: Hewlett-Packard Company Device 1854
Kernel driver in use: lpc_ich
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
Subsystem: Hewlett-Packard Company Device 1854
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
Subsystem: Hewlett-Packard Company Device 1854
01:00.0 Network controller: Ralink corp. Device 539b
Subsystem: Hewlett-Packard Company Device 18ed
Kernel driver in use: rt2800pci
02:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)
Subsystem: Hewlett-Packard Company Device 1854
Kernel driver in use: rtsx_pci
08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)
Subsystem: Hewlett-Packard Company Device 1854
Kernel driver in use: r8169
As you can see, i915 is not loaded for the VGA controller, even though it should be. I do a modprobe i915, in case for whatever reason udev can't seem to do it, run lspci -k and nothing changes. dmesg doesn't even seem to acknowledge that I did anything.
Does the i915 driver not support this chipset? That seems highly unlikely.
Last edited by Yaro (2013-04-26 14:07:36)

My computer on my signature is newer than yours and its supported.
I guess there is a backlight issue on your computer. try removing nomodeset and append
acpi_backlight=vendor
to your kernel comand line. Tell us what u see.

Headphones not detected in Windows 7

Hi, until about 2 weeks ago I have had no sound problems with my 17" 2011 Macbook Pro. I use Windows 7 64 Ultimate via Bootcamp.
Suddenly the computer no longer detects if headphones are plugged in or not. I have to manually use the sound device settings to switch between headphones and speakers. This was working fine until fairly recently.
Have applied all the latest updates on both the Mac OS and Windows sides.
Appreciate the help

Ok the SMC / PRAM process works to revover the headphone on OSX Lion, pfiou!
I try under Windows 7 now & let you know
FYI :
Reset the SMC > Resetting the System Management Controller (SMC)
1. Shut down the computer.
2. Unplug the computer's power cord.
3. Wait fifteen seconds.
4. Attach the computer's power cord.
5. Wait five seconds, then press the power button to turn on the computer.
Then the PRAM > About NVRAM and PRAM
1. Shut down the computer.
2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
3. Turn on the computer.
4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.
6. Release the keys.

Headphones not detected after update to 5.1.1

Hi all, After updating to 5.1.1 my Z3C no longer detects when I plug in my headphones (neither the ones that came with the phone nor others). - Clearing data for Smart Connect doesn't help- Rerouting sound output with SoundAbout does work, but is not practical - it shows the jack itself is not broken, though- Installing SmartKey did nothing- Production week is 15W25, so not from the "faulty weeks" I have not done any "software repair" or factory reset yet. Anyone else experiencing the same issue after updating?

No, no solution. Support asked me to do a "software repair" through the Companion, and if that didn't help I would have to send the phone in for service. I have just gone through the repair procedure, but no luck. I guess there's no escaping sending away the phone, then. Now all I have to do is to somehow find a phone (that accepts nano SIM) that I can use in the mean time - I can't do my work without a phone

Lenovo y510p - Intel card is not detected

Hello,
Recently I bought Lenovo y510p laptop in that configuration:
Lenovo Y510p
Intel Core i7 4700MQ
RAM 8 GB ( 1 x 8 GB ) 1600 MHz / PC3-12800
1TB HDD, 8gb SSD
NVIDIAGeForce GT 755M
After some problems I installed Arch on it. I had problems with black screen on start. After all I wanted to install drivers for Nvidia Optimus. But when I typed `lspci` I got that response:
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06)
00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06)
00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05)
00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #4 (rev d5)
00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 (rev d5)
00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05)
00:1f.3 SMoBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05)
01:00.0 VGA compatible controller: NVIDIA Corporation GK107M [GeForce GT 755M] (rev a1)
01:00.1 Audio device: NVIDIA Corporation GK107 HDMI Audio Controller (rev a1)
07:00.0 3D controller: NVIDIA Corporation GK107M [GeForce GT 755M] (rev a1)
08:00.0 Ethernet controller: Qualcomm Atheros QCA8171 Gigabit Ethernet (rev 10)
09:00.0 Network controller: Intel Corporation Centrino Wireless-N 2230 (rev c4)
First thing I noticed is that my CPU is detected as Xeon, not i7 and there is no line with Intel VGA. But in /proc/cpuinfo` this CPU is detected as i7:
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 60
model name : Intel(R) Core(TM) i7-4700MQ CPU @ 2.40GHz
stepping : 3
microcode : 0x12
cpu MHz : 2921.156
cache size : 6144 KB
physical id : 0
siblings : 8
core id : 0
cpu cores : 4
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf eagerfpu pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 fma cx16 xtpr pdcm pcid sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm abm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase tsc_adjust bmi1 avx2 smep bmi2 erms invpcid
bogomips : 4791.76
clflush size : 64
cache_alignment : 64
address sizes : 39 bits physical, 48 bits virtual
power management:
// and rest till 7th proessor
Thanks for all answers.
Last edited by grzlus (2014-08-29 16:34:55)

You mean you don't have a Nvidia card in the UltraBay? And Windows shows 2 Nvidia GPUs and Intel GPU at the same time?
Have you checked BIOS/UEFI settings? From what I read, this thing has a hardware mux, so even with just one Nvidia GPU it's possible to switch between Intel/Nvidia/Optimus. But I couldn't tell if this can be done in BIOS/UEFI or if it requires some more magic that's done from Windows.

[SOLVED] Intel DRI does not work after update

Hi,
after update of kernel from 3.5.6 to 3.6.5 and intel driver and deletion of dri2proto and mesa via pacman -Qdt (there are no more dependencies).. acceleration is no longer working
$ export LIBGL_DEBUG=verbose; glxinfo | grep renderer
libGL: OpenDriver: trying /usr/lib/xorg/modules/dri/tls/i965_dri.so
libGL: OpenDriver: trying /usr/lib/xorg/modules/dri/i965_dri.so
libGL error: failed to open drm device: Permission denied
libGL error: failed to load driver: i965
libGL: OpenDriver: trying /usr/lib/xorg/modules/dri/tls/swrast_dri.so
libGL: OpenDriver: trying /usr/lib/xorg/modules/dri/swrast_dri.so
libGL: Can't open configuration file /etc/drirc: No such file or directory.
OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 0x301)
Configuration:
SandyBridge I5, Intel HD 3000
Can somebody help?
Last edited by microcz (2012-11-07 06:15:23)

OT: A simpler way to check if some packages are installed:
$ pacman -Q intel-dri libgl foobar
intel-dri 9.0-1
libgl 9.0-1
error: package 'foobar' was not found
What's the output of 'groups'? Maybe you need to add yourself to 'video' group?
http://www.linuxquestions.org/questions … nf-794105/
http://www.mail-archive.com/dri-devel@l … 41313.html

[SOLVED] IPS Monitor Resolution Not Detected

I just got one of the new Catleap 27" IPS monitors. It works fine in Windows at its native 2560x1440 but arch doesn't seem to be detecting it properly
Screen 0: minimum 8 x 8, current 2720 x 1080, maximum 16384 x 16384
DVI-I-0 disconnected (normal left inverted right x axis y axis)
DVI-I-1 disconnected (normal left inverted right x axis y axis)
DVI-I-2 connected 800x600+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
800x600 60.3*+
HDMI-0 disconnected (normal left inverted right x axis y axis)
DP-0 disconnected (normal left inverted right x axis y axis)
DVI-I-3 connected 1920x1080+800+0 (normal left inverted right x axis y axis) 531mm x 298mm
1920x1080 60.0*+ 60.0
1440x900 59.9
1280x1024 60.0
1280x800 59.8
1152x864 75.0
1024x768 70.1 60.0
800x600 60.3 56.2
640x480 59.9
DP-1 disconnected (normal left inverted right x axis y axis)
DVI-I-3 is my second monitor (a regular LCD) which works fine. I think DVI-I-2 is the Catleap. Oddly, the manual says it supports 800x600 but it won't even turn on when X is started. Also it works fine when X isn't started. Whenever I switch to a different TTY my second monitor turns off and the Catleap turns on (albeit at a low resolution).
I've tried adding a new resolution mode with xrandr, but that gives me an error
# xrandr --newmode "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync
# xrandr --addmode DVI-I-2 2560x1440_60.00
X Error of failed request: BadMatch (invalid parameter attributes)
Major opcode of failed request: 153 (RANDR)
Minor opcode of failed request: 18 (RRAddOutputMode)
Serial number of failed request: 37
Current serial number in output stream: 38
I've tried various xorg.conf settings and using nvidia-settings, but nothing I do can get it to use a higher resolution or even turn on for that matter. I'm not sure if my dual monitor setup could be screwing with it. I've tried disconnecting my second monitor but that doesn't seem to help.
I found this article, which says that the Catleap's EDID isn't in Linux by default so you can specify it manually. So I set up my xorg.conf.d directory as follows
# 90-serverlayout.conf
Section "ServerLayout"
Identifier "Main"
Screen 0 "Acer V243"
Screen 1 "Catleap Q270" LeftOf "Acer V243"
Option "Xinerama" "1"
EndSection
# 30-screen-acerv243.conf
Section "Monitor"
Identifier "Acer V243H"
HorizSync 31.0 - 83.0
VertRefresh 56.0 - 76.0
Option "DPMS"
EndSection
Section "Screen"
Identifier "Acer V243"
Device "GTX 570 DVI 2"
Monitor "Acer V243H"
DefaultDepth 24
SubSection "Display"
Depth 24
EndSubSection
EndSection
# 30-screen-qhd270.conf
Section "Monitor"
Identifier "QHD270"
VendorName "ACB"
ModelName "QHD270"
VertRefresh 60
Mode "2560x1440"
DotClock 241.500000
HTimings 2560 2608 2640 2720
VTimings 1440 1443 1448 1481
Flags "-HSync" "+VSync"
EndMode
EndSection
Section "Screen"
Identifier "Catleap Q270"
Device "GTX 570 DVI 1"
Monitor "QHD270"
DefaultDepth 24
Option "UseEdid" "FALSE"
SubSection "Display"
Depth 24
Modes "2560x1440"
ViewPort 0 0
Virtual 2560 1440
EndSubSection
EndSection
# 20-nvidia.conf
Section "Device"
Identifier "GTX 570 DVI 1"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce GTX 570"
Screen 1
Option "UseDisplayDevice" "DFP-0"
Option "DynamicTwinView" "FALSE"
EndSection
Section "Device"
Identifier "GTX 570 DVI 2"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce GTX 570"
Screen 0
Option "UseDisplayDevice" "DFP-3"
Option "DynamicTwinView" "FALSE"
EndSection
Which doesn't work. The Catleap still won't turn on and the mouse position is all screwed up on my Acer. If I comment out the screen 1 line in the ServerLayout, the Acer works fine on its own.
Last edited by silverhammermba (2012-11-14 02:00:51)

Switching to the open source driver fixed my problem.

[SOLVED]Broadcom BCM4313 does not detect all wireless networks

EDIT:
I'm really sorry to the Arch forum users and to the admins for posting such easy problems which i could have fixed myself.
To solve this what i did was to change the channel on the router and its 802.11 mode. I turned my main machine on and it was doing the same as the machine i posted here first so it was two machines and so probably not a problem of the pc but of the router.
I don't know if this means my network cards are just bad or something else but it works now.
Hello,
I'm having a problem with the computer on the title. When i try connect the computer over wifi(to my own network), it doesn't "see" my network. Sees all my neighbours networks but not mine. It was working till a couple of days ago.
lspci -k
05:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)
Subsystem: Wistron NeWeb Corp. Device 051a
Kernel driver in use: bcma-pci-bridge
Kernel modules: bcma
rfkill list
0: samsung-wlan: Wireless LAN
Soft blocked: no
Hard blocked: no
1: samsung-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
2: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
3: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
I tried changing the encryption on the router from WPA&WPA2 to WEP and to WPA and i from TKIP&AES to simply AES but to no avail.
I also tried loading different modules still related to b43(like the legacy one) and installing the firmware from AUR.
Has this happen to anyone else?
I'm still trying to do this on the live iso so i can try as much stuff as needed and then i can just reboot and then do just what i need:)
thank you
Last edited by jantonio2992 (2014-07-20 11:22:03)

ewaller wrote:It sounds like your regulatory domain is not set correctly. Not all channels are legal to use in all countries. Perhaps your router had been using a channel legally, but your computer is unaware of its location, and was therefore ignoring the channel. Also, I assume you are in the right band. I don't know about your system, but thus ancient laptop does not work in the 5GHz band.
Thank you for shedding some light on the subject, but actually the channels the router permits are through 2.412 to 2.472 (more less, i think that writing here 13 frequencies wont help anyone ), and what i did was look on my working laptop, the channel for the networks around the house and select on my router a channel that wouldn't be the same, but i think the router has a built in tool to do this.

[Solved] Catalyst and RandR not detecting monitors

SOLUTION
The xorg.conf that CCC configures, even when xinerama is disabled, does not work with RandR. I gutted everything so only my primary monitor was in xorg.conf, then added the line 'Virtual' where appropriate with the correct square size of my total monitor space. xrandr then detects everything fine, and was able to use xrandr to get the screens working. Openbox only needs one session. Life is good.
Working xorg.conf with RandR:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "0-DFP5"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "Primary" "true"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
Option "PreferredMode" "2560x1440"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
Option "Monitor-DFP5" "0-DFP5"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
DefaultDepth 24
SubSection "Display"
Virtual 5920 1440
Depth 24
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
Option "RENDER" "Enable"
EndSection
Original Problem
Hi,
I'm moving from Xinerama (Which worked well for most things) to RandR. To get randr loading first thing I did was disable Xinerama in Catalyst Control Centre, restarted X.
My xorg.conf (Generated by CCC) has all monitors and modes listed correctly, and my middle (Primary) monitor (DFP5) works fine. My two sides, DFP9 and DFP10, are blank. I can move the cursor over to them, but that's about it.
xrandr does not appear to detect DFP9 and DFP10 as being connected.
I am using catalyst-total from AUR.
I've included all info I think may be helpful.
EDIT:
Seems my main issue was that Openbox needs a session on each X screen. So I can now use each X screen, but I can't alt tab across every window because the sessions don't talk to each other. randr still does not work though.
cat /var/log/Xorg.0.log | grep RandR
[ 6906.988] (II) fglrx(0): RandR 1.2 support is enabled!
[ 6906.988] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[ 6907.124] (II) fglrx(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6907.241] (--) RandR disabled
[ 6907.260] (II) fglrx(1): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6907.322] (--) RandR disabled
[ 6907.340] (II) fglrx(2): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6907.388] (--) RandR disabled
/etc/X11/xorg.conf:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 1680 0
Screen "amdcccle-Screen[1]-1" 4240 0
Screen "amdcccle-Screen[1]-2" 0 0
EndSection
Section "Module"
EndSection
Section "ServerFlags"
Option "Xinerama" "off"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "0-DFP5"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "Primary" "true"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
Option "PreferredMode" "2560x1440"
EndSection
Section "Monitor"
Identifier "0-DFP10"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
Option "PreferredMode" "1680x1050"
EndSection
Section "Monitor"
Identifier "0-DFP9"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
Option "PreferredMode" "1680x1050"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
Option "Monitor-DFP5" "0-DFP5"
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "amdcccle-Device[1]-1"
Driver "fglrx"
Option "Monitor-DFP10" "0-DFP10"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Device"
Identifier "amdcccle-Device[1]-2"
Driver "fglrx"
Option "Monitor-DFP9" "0-DFP9"
BusID "PCI:1:0:0"
Screen 2
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "amdcccle-Screen[1]-1"
Device "amdcccle-Device[1]-1"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "amdcccle-Screen[1]-2"
Device "amdcccle-Device[1]-2"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
Option "RENDER" "Enable"
EndSection
xrandr
Screen 0: minimum 320 x 200, current 2560 x 1440, maximum 2560 x 2560
DFP5 connected 2560x1440+0+0 (normal left inverted right x axis y axis) 597mm x 336mm
2560x1440 60.0*+
1800x1440 60.0
1856x1392 60.0
1792x1344 60.0
1920x1200 59.9
1920x1080 60.0 50.0 59.9 30.0 25.0 24.0 30.0 24.0
1600x1200 60.0
1776x1000 50.0 59.9 25.0 24.0 30.0
1680x1050 60.0
1400x1050 60.0
1600x900 60.0
1280x1024 75.0 60.0
1440x900 60.0
1280x960 75.0 60.0
1280x800 59.8
1152x864 60.0 75.0
1280x768 59.8
1280x720 60.0 50.0 59.9
1024x768 75.0 60.0
1152x648 50.0 59.9
800x600 75.0 60.3
720x480 60.0 59.9
640x480 75.0 59.9
DFP1 disconnected (normal left inverted right x axis y axis)
DFP2 disconnected (normal left inverted right x axis y axis)
DFP3 disconnected (normal left inverted right x axis y axis)
DFP4 disconnected (normal left inverted right x axis y axis)
DFP6 disconnected (normal left inverted right x axis y axis)
DFP7 disconnected (normal left inverted right x axis y axis)
DFP8 disconnected (normal left inverted right x axis y axis)
DFP9 disconnected (normal left inverted right x axis y axis)
DFP10 disconnected (normal left inverted right x axis y axis)
CRT1 disconnected (normal left inverted right x axis y axis)
Last edited by deags (2013-02-16 11:16:34)

SOLUTION
The xorg.conf that CCC configures, even when xinerama is disabled, does not work with RandR. I gutted everything so only my primary monitor was in xorg.conf, then added the line 'Virtual' where appropriate with the correct square size of my total monitor space. xrandr then detects everything fine, and was able to use xrandr to get the screens working. Openbox only needs one session. Life is good.
Working xorg.conf with RandR:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "0-DFP5"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "Primary" "true"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
Option "PreferredMode" "2560x1440"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
Option "Monitor-DFP5" "0-DFP5"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
DefaultDepth 24
SubSection "Display"
Virtual 5920 1440
Depth 24
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
Option "RENDER" "Enable"
EndSection
Original Problem
Hi,
I'm moving from Xinerama (Which worked well for most things) to RandR. To get randr loading first thing I did was disable Xinerama in Catalyst Control Centre, restarted X.
My xorg.conf (Generated by CCC) has all monitors and modes listed correctly, and my middle (Primary) monitor (DFP5) works fine. My two sides, DFP9 and DFP10, are blank. I can move the cursor over to them, but that's about it.
xrandr does not appear to detect DFP9 and DFP10 as being connected.
I am using catalyst-total from AUR.
I've included all info I think may be helpful.
EDIT:
Seems my main issue was that Openbox needs a session on each X screen. So I can now use each X screen, but I can't alt tab across every window because the sessions don't talk to each other. randr still does not work though.
cat /var/log/Xorg.0.log | grep RandR
[ 6906.988] (II) fglrx(0): RandR 1.2 support is enabled!
[ 6906.988] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[ 6907.124] (II) fglrx(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6907.241] (--) RandR disabled
[ 6907.260] (II) fglrx(1): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6907.322] (--) RandR disabled
[ 6907.340] (II) fglrx(2): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 6907.388] (--) RandR disabled
/etc/X11/xorg.conf:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 1680 0
Screen "amdcccle-Screen[1]-1" 4240 0
Screen "amdcccle-Screen[1]-2" 0 0
EndSection
Section "Module"
EndSection
Section "ServerFlags"
Option "Xinerama" "off"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "0-DFP5"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "Primary" "true"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
Option "PreferredMode" "2560x1440"
EndSection
Section "Monitor"
Identifier "0-DFP10"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
Option "PreferredMode" "1680x1050"
EndSection
Section "Monitor"
Identifier "0-DFP9"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
Option "PreferredMode" "1680x1050"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
Option "Monitor-DFP5" "0-DFP5"
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "amdcccle-Device[1]-1"
Driver "fglrx"
Option "Monitor-DFP10" "0-DFP10"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Device"
Identifier "amdcccle-Device[1]-2"
Driver "fglrx"
Option "Monitor-DFP9" "0-DFP9"
BusID "PCI:1:0:0"
Screen 2
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "amdcccle-Screen[1]-1"
Device "amdcccle-Device[1]-1"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "amdcccle-Screen[1]-2"
Device "amdcccle-Device[1]-2"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
Option "RENDER" "Enable"
EndSection
xrandr
Screen 0: minimum 320 x 200, current 2560 x 1440, maximum 2560 x 2560
DFP5 connected 2560x1440+0+0 (normal left inverted right x axis y axis) 597mm x 336mm
2560x1440 60.0*+
1800x1440 60.0
1856x1392 60.0
1792x1344 60.0
1920x1200 59.9
1920x1080 60.0 50.0 59.9 30.0 25.0 24.0 30.0 24.0
1600x1200 60.0
1776x1000 50.0 59.9 25.0 24.0 30.0
1680x1050 60.0
1400x1050 60.0
1600x900 60.0
1280x1024 75.0 60.0
1440x900 60.0
1280x960 75.0 60.0
1280x800 59.8
1152x864 60.0 75.0
1280x768 59.8
1280x720 60.0 50.0 59.9
1024x768 75.0 60.0
1152x648 50.0 59.9
800x600 75.0 60.3
720x480 60.0 59.9
640x480 75.0 59.9
DFP1 disconnected (normal left inverted right x axis y axis)
DFP2 disconnected (normal left inverted right x axis y axis)
DFP3 disconnected (normal left inverted right x axis y axis)
DFP4 disconnected (normal left inverted right x axis y axis)
DFP6 disconnected (normal left inverted right x axis y axis)
DFP7 disconnected (normal left inverted right x axis y axis)
DFP8 disconnected (normal left inverted right x axis y axis)
DFP9 disconnected (normal left inverted right x axis y axis)
DFP10 disconnected (normal left inverted right x axis y axis)
CRT1 disconnected (normal left inverted right x axis y axis)
Last edited by deags (2013-02-16 11:16:34)

(Solved) [Intel HDA] Headphones not detected

Similar Messages

Maybe you are looking for