[Solved] irexec: could not connect to socket

I am trying to start irexec via .xinitrc which has worked fine for me pre-systemd, but now I am getting the following error:
irexec: could not connect to socket
irexec: no such file or directory
Lirc is running fine, remote works in mythtv.
Here's my .xinitrc
cat ~/.xinitrc
#!/bin/sh
# ~/.xinitrc
# Executed by startx (run your window manager from here)
# exec gnome-session
# exec startkde
# exec startxfce4
# ...or the Window Manager of your choice
#exec xterm
#start irexec
irexec &
#exec /usr/bin/xbmc &
#turn off screensaver
xset s off -dpms
#start xfce4
exec startxfce4
and my lirc
cat /usr/lib/systemd/system/lirc.service
[Unit]
Description=Linux Infrared Remote Control
[Service]
ExecStartPre=/usr/bin/ln -sf /run/lirc/lircd /dev/lircd
ExecStart=/usr/sbin/lircd --pidfile=/run/lirc/lircd.pid
Type=forking
PIDFile=/run/lirc/lircd.pid
[Install]
WantedBy=multi-user.target
and my /etc/conf.d/lircd.conf
cat /etc/conf.d/lircd.conf
# Parameters for lirc daemon
LIRC_DEVICE="/dev/lirc0"
LIRC_DRIVER=""
LIRC_EXTRAOPTS=""
LIRC_CONFIGFILE=""
I tried starting irexec via systemd, too, but that did not work either:
sudo systemctl status irexec.service
irexec.service - IR Exec
Loaded: loaded (/usr/lib/systemd/system/irexec.service; enabled)
Active: inactive (dead) since Sun 2013-04-21 20:17:11 CST; 1s ago
Process: 459 ExecStart=/usr/bin/irexec --daemon (code=exited, status=0/SUCCESS)
Apr 21 20:17:11 frontend systemd[1]: Starting IR Exec...
Apr 21 20:17:11 frontend systemd[1]: Started IR Exec.
cat /usr/lib/systemd/system/irexec.service
[Unit]
Description=IR Exec
After=lirc.service
Wants=lirc.service
[Service]
ExecStart=/usr/bin/irexec --daemon
Type=forking
[Install]
WantedBy=multi-user.target
Any help or pointers will be much appreciated.
Last edited by dafrizz (2013-06-08 23:58:25)

Thanks for your help so far. I thought it was the other way around, my mistake,
Still no luck, now I get the following:
sudo systemctl start irexec
Job for irexec.service failed. See 'systemctl status irexec.service' and 'journalctl -xn' for details.
sudo systemctl status irexec
irexec.service - IR Exec
Loaded: loaded (/etc/systemd/system/irexec.service; enabled)
Active: failed (Result: timeout) since Sat 2013-06-08 16:16:17 CST; 10s ago
Process: 11748 ExecStart=/usr/bin/irexec (code=killed, signal=TERM)
Jun 08 16:14:47 frontend systemd[1]: Starting IR Exec...
Jun 08 16:16:17 frontend systemd[1]: irexec.service operation timed out. Terminating.
Jun 08 16:16:17 frontend systemd[1]: Failed to start IR Exec.
Jun 08 16:16:17 frontend systemd[1]: Unit irexec.service entered failed state.
sudo journalctl -xn
-- Logs begin at Sat 2013-04-20 18:36:51 CST, end at Sat 2013-06-08 16:16:44 CST. --
Jun 08 16:15:41 frontend sudo[11759]: pam_unix(sudo:session): session closed for user root
Jun 08 16:16:17 frontend systemd[1]: irexec.service operation timed out. Terminating.
Jun 08 16:16:17 frontend systemd[1]: Failed to start IR Exec.
-- Subject: Unit irexec.service has failed
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/be02cf6855d2428ba40df7e9d022f03d
-- Unit irexec.service has failed.
-- The result is failed.
Jun 08 16:16:17 frontend systemd[1]: Unit irexec.service entered failed state.
Jun 08 16:16:17 frontend sudo[11745]: pam_unix(sudo:session): session closed for user root

Similar Messages

  • TS1368 I could not connect to the i tunes store as an error occured (-3212) any help in solving this problem would be most grateful

    I could not connect to the I Tunes store as an error occured with the number as follows (3212) any one out there that knows what has happened and how can I rectify look forward to your replies

    Hi c1r1g1,
    If you are having an issue connecting to the iTunes Store, you may find the following article helpful:
    Apple Support: Can't connect to the iTunes Store
    http://support.apple.com/kb/ts1368
    Regards,
    - Brenden

  • I received this error: "iTunes could not connect to the iTunes Store. An unknown error occurred (-3212). Make sure your network connection is active and try again." We are connected. Any ideas on how to solve this?

    I downloaded iTunes. I was going to put an MP3 lecture on iTunes so I could put it on our new iPad but I got the message:
    "iTunes could not connect to the iTunes store. An unknown error occurred (-3212). Make sure your network connection is active and try again." I was able to get on this site so I know the connection is fine. Any ideas how to fix this?
    Thanks.

    Hello Buck
    If you are having issues with the iTunes store, check out the article below.
    Can't connect to the iTunes Store
    http://support.apple.com/kb/ts1368
    Thanks for using Apple Support Communities.
    Regards,
    -Norm G.

  • Connection test to database failed: could not connect to server

    I restarted one of my HPOV NNMi 9.23 servers this morning and NNMi is no longer loading.  I am seeing the following errors in the logs indicated:
    /var/opt/OV/log/nnm/public/nmsdbmgr.log
    04/06/2015 09:28:05 AM Connection test to database failed: could not connect to server: Connection refused
    Is the server running on host "127.0.0.1" and accepting
    TCP/IP connections on port 5432?
    /var/opt/OV/log/nnm/public/postgres.log
    2015-04-06 09:25:55.312 EDT: :8580:0LOG: could not translate host name "localhost", service "5432" to address: Name or service not known
    2015-04-06 09:25:55.312 EDT: :8580:0WARNING: could not create listen socket for "localhost"
    2015-04-06 09:25:55.312 EDT: :8580:0FATAL: could not create any TCP/IP sockets
    I checked /etc/hosts and found the following entry:
    #; Local
    127.0.0.1 localhost
    From the command line I can ping localhost with no issue.  Not sure why NNMi is not starting at this point. 
    This question was solved.
    View Solution.

    I also attempted to do a reset using nnmresetebdb.ovpl.  I recieved the following:
    Attempting to reset the embedded database...
    Starting nmsdbmgr process for database reset...
    nmsdbmgr process did not restart successfully - please try reset again.
    When I run ovstart -c I receive the following:
    Name PID State Last Message(s)
    OVsPMD 29831 RUNNING -
    pmd 29832 RUNNING Initialization complete.
    nmsdbmgr - NOT_RUNNING - Exit(1)
    ovjboss - UNSTARTABLE -
    nnmaction - UNSTARTABLE -
    ovspmd: Attempt to start HP OpenView services is complete.
    I definitely need some help with this please!  
    Thanks!

  • WICD "Could not connect to wicd's D-bus interface"

    I'm getting this error when using WICD.
    Could not connect to wicd's D-bus interface. Check the wicd log for error message.
    When I run wicd-client thru the terminal I get:
    [scott@Arch ~]$ wicd-client
    ** (process:1372): WARNING **: Trying to register gtype 'GMountMountFlags' as enum when in fact it is of type 'GFlags'
    ** (process:1372): WARNING **: Trying to register gtype 'GDriveStartFlags' as enum when in fact it is of type 'GFlags'
    ** (process:1372): WARNING **: Trying to register gtype 'GSocketMsgFlags' as enum when in fact it is of type 'GFlags'
    Has notifications support True
    Loading...
    Connecting to daemon...
    Can't connect to the daemon, trying to start it automatically...
    Can't connect to the daemon, trying to start it automatically...
    Failed to find a graphical sudo program, cannot continue.
    I tried to find the wicd config files in /etc/wicd but could not find them. I also cannot seem the find the log file that the error message is telling me to look at.
    I have installed:
    wicd 1.7.2.4-3
    wicd-gtk 1.7.2.4-3
    dbus-core 1.6.2-2
    dbus 1.6.2-1
    slim 1.3.3-5
    xfce 4.10
    xfce4-goodies

    venam wrote:Hello Psyconaughty,
    I remember having the exact similar issue on another distro, however it did not interfere with the connection (I could still connect to the internet correctly).
    What I've done to solve this problem on the other distro is the following:
    dpkg-reconfigure wicd
    update-rc.d wicd defaults
    I am not sure about the commands here, maybe they are not valid for Arch.
    hope this help.
    I tried this earlier and Arch doesn't recognise the commands. I think that is a Debian command(Correct  me if I'm wrong). I also assume that uninstalling it a reinstalling it would do the rconfigure but it it dosen't someone let me know how to auto reconfigure.
    Also I went into my daemon log and saw some falures. The problem looks like it might be ConsoleKit. I have reinstalled ConsoleKit and still getting errors.
    Here is my last loggin (From file /var/log/daemon.log):
    Jul 9 15:58:05 localhost init: Switching to runlevel: 6
    Jul 9 15:58:06 localhost dhcpcd[1416]: received SIGTERM, stopping
    Jul 9 15:58:06 localhost dhcpcd[1416]: eth0: removing interface
    Jul 9 11:59:28 localhost [ 1.773006] udevd[82]: starting version 185
    Jul 9 11:59:28 localhost [ 4.346105] udevd[198]: starting version 185
    Jul 9 11:59:30 localhost ntpd[520]: ntpd [email protected] Sat Jun 9 05:23:54 UTC 2012 (1)
    Jul 9 11:59:30 localhost ntpd[521]: proto: precision = 0.248 usec
    Jul 9 11:59:30 localhost ntpd[521]: ntp_io: estimated max descriptors: 1024, initial socket boundary: 16
    Jul 9 11:59:30 localhost ntpd[521]: Listen and drop on 0 v4wildcard 0.0.0.0 UDP 123
    Jul 9 11:59:30 localhost ntpd[521]: Listen and drop on 1 v6wildcard :: UDP 123
    Jul 9 11:59:30 localhost ntpd[521]: Listen normally on 2 lo 127.0.0.1 UDP 123
    Jul 9 11:59:30 localhost ntpd[521]: Listen normally on 3 lo ::1 UDP 123
    Jul 9 11:59:30 localhost ntpd[521]: peers refreshed
    Jul 9 11:59:30 localhost ntpd[521]: Listening on routing socket on fd #20 for interface updates
    Jul 9 11:59:38 localhost dbus[471]: [system] Activating service name='org.freedesktop.ConsoleKit' (using servicehelper)
    Jul 9 11:59:39 localhost console-kit-daemon[597]: WARNING: polkit_authority_get: Error getting authority: Error initializing authority: Could not connect: No such file or directory
    Jul 9 11:59:39 localhost dbus[471]: [system] Successfully activated service 'org.freedesktop.ConsoleKit'
    Jul 9 11:59:44 localhost dbus[471]: [system] Activating service name='org.wicd.daemon' (using servicehelper)
    Jul 9 11:59:44 localhost dbus[471]: [system] Activated service 'org.wicd.daemon' failed: Launch helper exited with unknown return code 1
    Jul 9 11:59:44 localhost console-kit-daemon[597]: CRITICAL: polkit_authority_check_authorization: assertion `POLKIT_IS_AUTHORITY (authority)' failed
    Jul 9 11:59:44 localhost dbus[471]: [system] Activating service name='org.wicd.daemon' (using servicehelper)
    Jul 9 11:59:44 localhost dbus[471]: [system] Activated service 'org.wicd.daemon' failed: Launch helper exited with unknown return code 1
    Jul 9 11:59:45 localhost console-kit-daemon[597]: CRITICAL: polkit_authority_check_authorization: assertion `POLKIT_IS_AUTHORITY (authority)' failed
    Jul 9 12:00:09 localhost console-kit-daemon[597]: CRITICAL: polkit_authority_check_authorization: assertion `POLKIT_IS_AUTHORITY (authority)' failed
    Jul 9 12:00:10 localhost console-kit-daemon[597]: CRITICAL: polkit_authority_check_authorization: assertion `POLKIT_IS_AUTHORITY (authority)' failed
    Jul 9 12:00:29 localhost dbus[471]: [system] Failed to activate service 'org.freedesktop.Avahi': timed out
    Jul 9 12:00:34 localhost dbus[471]: [system] Activating service name='org.freedesktop.UPower' (using servicehelper)
    Jul 9 12:00:34 localhost dbus[471]: [system] Successfully activated service 'org.freedesktop.UPower'
    Jul 9 12:00:34 localhost dbus[471]: [system] Activating service name='org.freedesktop.UPower' (using servicehelper)
    Jul 9 12:00:34 localhost dbus[471]: [system] Successfully activated service 'org.freedesktop.UPower'
    Jul 9 12:00:34 localhost dbus[471]: [system] Activating service name='org.freedesktop.PolicyKit1' (using servicehelper)
    Jul 9 12:00:35 localhost dbus[471]: [system] Activating service name='org.freedesktop.UPower' (using servicehelper)
    Jul 9 12:00:35 localhost dbus[471]: [system] Successfully activated service 'org.freedesktop.UPower'
    Jul 9 12:00:35 localhost dbus[471]: [system] Activating service name='org.freedesktop.UPower' (using servicehelper)
    Jul 9 12:00:35 localhost dbus[471]: [system] Successfully activated service 'org.freedesktop.UPower'
    Jul 9 12:00:59 localhost dbus[471]: [system] Failed to activate service 'org.freedesktop.PolicyKit1': timed out
    Jul 9 12:00:59 localhost dbus[471]: [system] Activating service name='org.freedesktop.PolicyKit1' (using servicehelper)
    Jul 9 12:01:24 localhost dbus[471]: [system] Failed to activate service 'org.freedesktop.PolicyKit1': timed out
    Jul 9 12:01:24 localhost dbus[471]: [system] Activating service name='org.freedesktop.PolicyKit1' (using servicehelper)
    Jul 9 12:01:49 localhost dbus[471]: [system] Failed to activate service 'org.freedesktop.PolicyKit1': timed out
    Jul 9 12:02:30 localhost dbus[471]: [system] Reloaded configuration
    Jul 9 12:02:30 localhost dbus[471]: [system] Reloaded configuration
    Jul 9 12:02:30 localhost dbus[471]: [system] Reloaded configuration
    Jul 9 12:02:30 localhost dbus[471]: [system] Reloaded configuration
    Jul 9 12:04:17 localhost dhcpcd[955]: version 5.5.6 starting
    Jul 9 12:04:17 localhost dhcpcd[955]: eth0: waiting for carrier
    Jul 9 12:04:19 localhost dhcpcd[955]: eth0: carrier acquired
    Jul 9 12:04:19 localhost dhcpcd[955]: eth0: sending IPv6 Router Solicitation
    Jul 9 12:04:19 localhost dhcpcd[955]: eth0: sendmsg: Cannot assign requested address
    Jul 9 12:04:19 localhost dhcpcd[955]: eth0: rebinding lease of 10.42.0.65
    Jul 9 12:04:19 localhost dhcpcd[955]: eth0: acknowledged 10.42.0.65 from 10.42.0.1
    Jul 9 12:04:19 localhost dhcpcd[955]: eth0: checking for 10.42.0.65
    Jul 9 12:04:23 localhost dhcpcd[955]: eth0: sending IPv6 Router Solicitation
    Jul 9 12:04:24 localhost dhcpcd[955]: eth0: leased 10.42.0.65 for 3600 seconds
    Jul 9 12:04:24 localhost dhcpcd[955]: forked to background, child pid 987
    Jul 9 12:04:26 localhost dhcpcd[990]: dhcpcd already running on pid 987 (/run/dhcpcd-eth0.pid)
    Jul 9 12:04:27 localhost dhcpcd[987]: eth0: sending IPv6 Router Solicitation
    Jul 9 12:04:31 localhost dhcpcd[987]: eth0: sending IPv6 Router Solicitation
    Jul 9 12:04:31 localhost dhcpcd[987]: eth0: no IPv6 Routers available
    Jul 9 16:09:11 localhost console-kit-daemon[597]: CRITICAL: polkit_authority_check_authorization: assertion `POLKIT_IS_AUTHORITY (authority)' failed
    Jul 9 16:09:36 localhost console-kit-daemon[597]: CRITICAL: polkit_authority_check_authorization: assertion `POLKIT_IS_AUTHORITY (authority)' failed
    Jul 9 16:10:01 localhost dbus[471]: [system] Activating service name='org.freedesktop.UPower' (using servicehelper)
    Jul 9 16:10:01 localhost dbus[471]: [system] Successfully activated service 'org.freedesktop.UPower'
    Jul 9 16:11:34 localhost init: Switching to runlevel: 6

  • ITunes RADIO is not working.  "iTunes could not connect to the iTunes Store. Make sure your internet connection is active and try again." Try as I may, as many as ten attempts, trying to connect after restart, after shutdown, nothing works. Just so -  iTu

    iTunes RADIO is not working.
    “iTunes could not connect to the iTunes Store. Make sure your internet connection is active and try again.” Try as I may, as many as ten attempts, trying to connect after restart, after shutdown, nothing works. Just so …
    iTunes STORE not “connectable” with my otherwise perfectly-working internet connection, viable, up and running for all other uses.
    Simply put, firstly, I can't connect to the internet when I click on Radio.  People are quite suspicious that this is Apple incompetence or your company's famous arrogance for this commonly-suffered problem that you won't or “can’t” fix.
    Read the many web comments and you won’t be pleased with yourselves: the suspicion is that if you ruin internet radio on iTunes, Apple will somehow make more money on music downloads, etc. Bull.
    Also, thirdly, my old playlist of 20 or so internet radio stations in the Ambient category STILL PLAYS !
    Then fourth, I installed the latest available version of QuickTime Player 7.app Version 7.6.6 but it didn’t solve the problem either. I had QuickTime Player.app Version 10.2, but substituted what Apple website said was the latest, LOWER NUMBERED QuickTime Player version of 7.6.6
    Fifth, I can't connect to iTunes store no matter what I do or what user group's advice I try. So I can’t buy or download anything from iTunes. Bad for business.
    Sixth, I updated to the latest version of iTunes but this weird problem remains. All suggested Apple fixes or user group fixes are useless. Where is Apple’s famous technical competency, vaunted customer support?, and user-friendly product reputation? Get it back, please.
    Solve this problem of yours ASAP for us, your numerous disgruntled, dissatisfied customers of iTunes. You can do better, should, and really –in all fairness- must.
    ===============================================================
    NOTE:  no password for iTunes exists in my Keychain. Is this a problem?
    Apple ACCOUNT ID, and iTunes ID password, works but not to access iTunes with my healthy internet connection.
    Apple store id It works via direct internet connetion but not through iTunes.  Very strange.
    ===============================================================
    FYI, Hardware Overview:
      Model Name:                       MacBook Pro
      Model Identifier:                 MacBookPro8,2
      Processor Name:               Intel Core i7
      Processor Speed:               2 GHz
      Number of Processors:    1
      Total Number of Cores:    4
      L2 Cache (per Core):         256 KB
      L3 Cache:                            6 MB
      Memory:                              16 GB
      Boot ROM Version:            MBP81.0047.B27
      SMC Version (system):      1.69f4
      Serial Number (system):   C0*******F8V
      Sudden Motion Sensor:
      State:   Disabled
    Intel 6 Series Chipset:
      Vendor: Intel
      Product:            6 Series Chipset
      Link Speed:       6 Gigabit
      Negotiated Link Speed:           6 Gigabit
      Description:      AHCI Version 1.30 Supported
    M4-CT512M4SSD2:
      Capacity:           512.11 GB (512,110,190,592 bytes)
      Model: M4-CT512M4SSD2                         
      Revision:           040H   
      Serial Number: 0000000012330912E75A
      Native Command Queuing:    Yes
      Queue Depth:   32
      Removable Media:        No
      Detachable Drive:        No
      BSD Name:         disk0
      Medium Type:      Solid State
      TRIM Support:     Yes
      Partition Map Type:     GPT (GUID Partition Table)
      S.M.A.R.T. status:         Verified
      Volumes:
    disk0s1:
      Capacity:           209.7 MB (209,715,200 bytes)
      BSD Name:         disk0s1
      Content:            EFI
    disk0s2:
      Capacity:           511.25 GB (511,250,432,000 bytes)
      BSD Name:         disk0s2
      Content:            Apple_CoreStorage
    Recovery HD:
      Capacity:           650 MB (650,002,432 bytes)
      BSD Name:         disk0s3
      Content:            Apple_Boot
      Volume UUID:   600737FB-7A29-3BAE-859E-CBFE2E90C39A
    <Edited by Host>

    This my sound too simple, but I just kept clikning on the arrow next to the selected music and it finally "Kicked" in.
    I live in Europe ,So Be persistent and don't give up !  Aug. 2013

  • Can somebody help me in finding a solution or an explanation to the problem I am currently experiencing as well as others wherein we cannot connect to the iTunes store (iTunes could not connect to the store. An unknown error occurred (0x80096004))?

    Can somebody help me in finding a solution or an explanation to the problem I am currently experiencing as well as others wherein we cannot connect to the iTunes store. An error message appears and either says "iTunes could not connect to the store. An unknown error occurred (0x80096004). Make sure your network connection is active and try again" or "iTunes could not connect to the store.Make sure your network connection is active and try again." Despite the fact that my network connection is working quite fine, this problem still persists. I can say that my connection is fine because I can surf the internet and furthermore, I used to connect to the iTunes store just before this incident happened which started from April 17, 2014 and persists until today. I tried to solve the problem by following the troubleshoot procedures given in the support section of this site but it really did not solve the problem. I believe that others are experiencing this situation as well very similar to mine when it comes to the time of occurrence as I have read in the discussions in this site. Even though we have different network connections, operating systems and other specifications, we still experience the same problem, so is there really a problem with our computers or is it with the iTunes? And by the way, my computer works under Windows XP. Thanks a lot. God bless.

    Try this...
    Triple click anywhere in the line below to select it and press Ctrl+C to copy it.
    cmd /k netsh winsock reset
    Press the WinLogoKey+R to open the run dialog, then Ctrl+V to paste, then press enter/return.
    You should get something similar to this:
    Reboot the computer and the problem should be resolved.
    If it doesn't work then perhaps a full tear down and rebuild of iTunes will fix things. See Troubleshooting issues with iTunes for Windows updates for details.
    tt2

  • Tried EVERYTHING!!! HELP!!! iTunes could not connect to the music store...

    HELP! I have tried everything...I keep receiving the following error message:
    "iTunes could not connect to the music store. Network connection was refused. Make sure your network settings are correct and network connection is active, then try again."
    I have a 60GB video ipod. OS Windows XP Service Pack 1. Dial up AOL. No firewalls, checked connections, followed all instructions on the support page, contacted customer support via email (see responses below), contacted AOL (referred me back to iTunes), iTunes referred me to customer support number for iPod (which I called, and they referred be back to iTunes customer support via email). After emailing customer support and receiving a general response, and replying to each response, the email said they were not technical support...read all emails below beginning with the most recent:
    Subj: Re: Connect; Follow-up:
    Date: 1/19/2006 6:04:50 PM Pacific Standard Time
    From: [email protected]
    To:
    Sent from the Internet (Details)
    Dear Emily,
    Thank you for contacting the iTunes Music Store. We're sorry to hear you are still unable to connect to the store. At the end of this email we have included further possible solutions to the issue you are encountering.
    We're also sorry your iTunes Music Gift email didn't reach the recipient. The gift code you purchased is ... The recipient's ISP may have inadvertently blocked or filtered our email, thinking it was spam.
    If you purchased your gift using iTunes, you can resend it with a few simple mouse clicks. Just follow these easy steps to resend an unredeemed music gift to any address:
    http://www.info.apple.com/kbnum/n301476
    If you would rather email the gift information directly to the recipient using your email program, we've included instructions for your recipient and the gift code below.
    1. Download and install the latest version of iTunes. You can download the latest version, free-of-charge, from our website.
    http://www.apple.com/itunes/download/
    2. Click the link below to launch the iTunes application and view the gift page.
    http://www.itunes.com/go/songcode/
    3. Click Redeem.
    4. Copy this gift code and paste it into the Redeem code entry box.
    Again, we're sorry you are still unable to connect to the store.
    First, please make sure you're using the latest version of iTunes before you access the iTunes Music Store. You can download the latest version of iTunes from our website.
    http://www.apple.com/itunes/download/
    Also, some software that you install on your computer can affect the way your computer sends and receives information from the Internet. A few examples of this software are:
    * Firewalls
    * Internet security software
    * Privacy filters
    * Web accelerators
    * Ad filters
    If you cannot use the iTunes Music Store, try disabling this software temporarily to identify the culprit. Then, please refer to the documentation that came with the software to allow the iTunes Music Store to connect to the Internet. For your reference, these domains need to be permitted to send and receive data from the Internet:
    phobos.apple.com
    phobos.apple.com.edgesuite.net
    For more instructions on configuring your 3rd-party software, please contact the software manufacturer. If your web accelerator appears to be at the root of the problem, please contact your ISP.
    Sincerely,
    The iTunes Music Store Team
    http://www.apple.com/support/itunes/ww/
    Thank you for your response. I am curious to know why if iTunes does not
    answer non technical questions, why I received information when I replied to this
    email. Listed below are the previous threads providing technical information.
    Furthermore, if this is email is for billing disputes, I would like to have
    my Mastercard credited $25.87 for a "gift this purchase/tv show" that I
    purchased for my uncle on Christmas Day. I purchased the full first season of Monk.
    I previously sent an email requesting credit on approximately January 2,
    2006, and failed to receive a response. He never received the gift, or any
    instructions about how to download the tv show, and I do not show a credit
    appearing on my credit card. I would like to have credit for services not received.
    Please credit the following card #XXXX
    Thank you.
    Emily
    Subj: Re: Connect; Follow-up:
    Date: 1/18/2006 2:21:12 PM Pacific Standard Time
    From: [email protected]
    To:
    Sent from the Internet (Details)
    Dear Emily,
    Thank you for contacting the iTunes Music Store.
    The iTunes Music Store team answers non-technical questions about billing,
    customer accounts, downloading music, and iTunes Music Store content.
    Many questions about your iTunes software can be answered by choosing “iTunes
    and Music Store Help” from the Help menu.
    For online information, visit iTunes Support at
    <http://www.apple.com/support/itunes>.
    To access the discussion boards for iTunes and other Apple services, please
    visit
    <http://discussions.info.apple.com>.
    For support for your iPod, please visit:
    <http://www.apple.com/support/ipod/>
    If you require assistance beyond the complimentary support available online,
    please call AppleCare technical support at 800-APL-CARE (800-275-2273). Help
    is available seven days a week from 8:00 a.m. to 8:00 p.m. central time. There
    may be a fee associated with the call.
    Sincerely,
    iTunes Music Store Support
    Need a quick answer?
    iTunes Music Store Customer Service:
    <http://www.apple.com/support/musicstore/ww>
    iTunes technical assistance:
    <http://www.apple.com/support/itunes/ww>
    Thank you for your response. I have tried these methods, AGAIN. None of
    them seem to work. I also contact my ISP, AOL. Nothing they advised me to do
    worked. Has iTunes performed recent upgrades? Just viewing the discussion
    boards, it seems like a lot of people are having problems. Having paid $399
    for
    the 60GB video ipod, I need more than a generic email telling me what to do,
    when I already indicated in previous email that I followed the steps shown in
    the
    support area, which were the same instructions email to me.
    Subj: Re: Connect; Follow-up:
    Date: 1/16/2006 5:14:47 PM Pacific Standard Time
    From: [email protected]
    Sent from the Internet (Details)
    Dear Emily,
    Thank you for contacting the iTunes Music Store. Use the steps in the
    following article to troubleshoot your connection problem.
    I have been unable to connect for more than 24 hours on Windows.
    If you haven't been able to connect to the iTunes Music Store for more than a
    day—and other customers on our discussion boards aren't experiencing similar
    issues—a software or ISP configuration issue may be blocking your access to
    the iTunes Music Store.
    • Your copy of the iTunes application may be out of date.
    • If iTunes is out of date, it will not be able to connect to the
    iTunes Music Store. You can download the latest version of iTunes from our
    website: ?http://www.apple.com/itunes/download/
    • You installed a third-party anti-virus or personal firewall
    application.
    • You will need to configure your software to allow iTunes to access
    the Music Store. You can contact the software manufacturer if you have
    questions regarding configuration. Click here for more information.
    • You upgraded to Windows XP Service Pack 2.
    • Windows XP Service Pack 2, by default, enables the Windows Firewall.
    As with a third-party firewall, you will need to configure Windows Firewall
    to allow iTunes to access the Music Store. Read this document for more
    information. If you have further questions about configuring the Windows Firewall,
    contact Microsoft's Service Pack 2 hotline at (888) SP2-HELP.
    • You upgraded to a high-speed or wireless Internet connection.
    • A new DSL or cable modem, or even a router, could be the culprit.
    These devices allow your computer to access the Internet at a much higher speed,
    or route your connection to multiple computers. However, they can also expose
    your computer to hackers. To help prevent this, manufacturers of these
    products often install firewalls to prevent hackers and viruses from compromising
    your system. Although this layer of protection is beneficial, there are
    occasions when a device may determine that the iTunes Music Store is a threat to the
    computer. If this is the case, you will need to configure these devices to
    allow iTunes to access the Music Store. Contact your ISP or the device
    manufacturer if you need help configuring your device.
    • You switched to a new ISP.
    • If you didn't install new networking hardware, your ISP may be
    blocking access to the iTunes Music Store. Let your ISP know about this document
    which can help your them configure their servers to allow iTunes Music Store
    traffic through.
    Sincerely,
    The iTunes Music Store team
    http://www.apple.com/support/itunes/ww/
    In a message dated 1/14/2006 8:20:29 AM Pacific Standard Time,
    [email protected] writes:
    http://www.info.apple.com/kbnum/n300870
    Thank you for your quick response. I already tried the link and all
    instructions several times.
    -The following is my information:
    Sacramento, CA
    -AOL 8.0 (dial up connection) - (tried downloading 9.0 but always receive
    error message)
    -The error message received is: iTunes cound not connect to the Music Store.
    Network connection was refused. Make sure your network settings are correct
    and network connection is active, then try again
    Thank you,
    Emily
    Subj: Re: Connect; Follow-up:
    Date: 1/14/2006 8:20:29 AM Pacific Standard Time
    From: [email protected]
    Sent from the Internet (Details)
    Dear Emily,
    We're sorry to hear that you can't connect to the iTunes Music Store. Your
    experience using the iTunes Music Store is very important to us, and we'll do
    everything we can to help you fix the connection issue quickly.
    This article outlines the culprits that can cause a connection issue. Please
    try these solutions:
    http://www.info.apple.com/kbnum/n300870
    We hope one of these solutions helped you resolve the connection issue. In
    the rare event that these suggestions didn't help, please reply to this email
    with the following information:
    1. Your city and state.
    2. Whether you use a high-speed Internet connection, like a cable modem or
    DSL.
    3. The name of your Internet Service Provider.
    4. The error message iTunes displayed (if any) when you tried to connect.
    5. Your approval to reset your password.
    Sincerely,
    The iTunes Music Store Team
    http://www.apple.com/support/itunes/ww/
    Customer First Name : Emily
    Customer Last Name :
    email :
    Web Order # :
    Support Subject : Connect
    Sub Issue : Can't connect
    Comments : iTunes Account Name:
    Platform : Windows XPSP1
    Error Code :
    Other Error :
    Comments:
    The error message I am receiving is "iTunes cound not connect to the Music
    Store. Network connection was refused. Make sure your network settings are
    correct and network connection is active, then try again". I have been unable to
    connect to the music store for at least 3-4 days. I have been using iTunes
    since last October, successfully. I checked all my network connections & they
    are fine. I am able to connect to AOL. I even uninstalled and reinstalled
    iTunes several times, all successfully, but I am still encountering a problem.
    Thank you.
    Emily
    Nice, effective customer service. I'm at my wit's end. I field customer service calls, and answer emails at work, and the general responses from the iTunes response library are ridiculous. Especially, after emailing me twice technical support emails, they tell me they do not handle technical support questions...
    Any help or suggestions as to how I should respond to the next email is helpful...
    I also forgot to mention I have been able to connect to iTunes since October 2005, and have been unable to connect for almost 2 weeks now. And, yes, I have downloaded the latest version of iTunes. I was advised over the phone to upgrade to XP Service Pack 2, but it looks like SP2 has issues. ANd, no, I did not download SP2, because the customer support rep admitted he knew nothing to very little about iTunes.
    Emily

    Emily,
    thanks for your posting, it just reflects my experience (although I didn't contact the helpdesk, but after what you wrote I think I can skip that part). I am livin in China and buy from the German MS, worked fine until about a week ago when the download of an album stopped just after 5 songs. I have never been able to connect to the shop ever since.
    The interesting thing is, that I get a response from their server in the domain phobos.apple.com (phobos.apple.com/WebObjects/MZStore.woa/wa/storeFront) which I would interpret that there can't be a problem which they always list (Antivirus, Firewall etc...)
    So will there ever be somebody from Apple who is going to give a better explanation how to solve the problem ? Or are there already too many people buying iPods and music ???

  • Officejet 6700 error while searching for updates: 'Printer could not connect to server'

    I recently purchase the Officejet 6700 Premium. While setting the printer up, I received the error 'The printer could not connect to the server.' I first received this while the printer was searching for updates. I later received the same error while trying to set up ePrint from my computer.
    The printer is connected through my wireless router. All other print services function normally. It is connected to the network, and I have printed several times over the wireless network.
    Though I don't think it matters, since the on-board print set-up gave me the error, I run Windows 7 64-bit on my computer.
    Thanks for any help!

    What is the IP address of the printer?  What is the make and model of the router that you use in the wireless set up? Is the router firmware up to date? 
    I would first try power cycling the router and the printer. Turn off/unplug the router and then power down the printer. Then plug the router back in and wait for it to be fully up and functioning before turning the printer back on.  After you have both pieces of equipment back on and functioning attempt to connect to web services again.
    If still having problems I would attempt to set a static DNS on the printer through the embedded web server (EWS) by entering the printer's IP address into the address bar of  a browser on a computer. 
    Once that computer displays that page click on the Network tab.
    Then look in the column to the left and find the Wireless section
    Click on IPv4
    Then on that page look at the 2nd section that is labeled DNS Address configuration
    Change the radio button to the manual option
    Then for the manual preferred fill it out and make sure it reads 8.8.8.8
    Secondary should be set to 8.8.4.4
    Then hit Apply
    Read the next screen carefully. That message with the "OK" button below it  is one that states to click that button to undo the changes you  just made.  Just navigate away from that page by clicking on another tab.
    Then reattempt to connect to web services.  
    I am a former employee of HP...
    How do I give Kudos?| How do I mark a post as Solved?

  • ITunes could not connect to the iTunes store. The network conect timed out

    I am having trouble with iTunes,
    Message: "iTunes could not connect to the iTunes store. The network conection timed out. Make sure your network settings are correct and your network connection is active then try again."
    Im not sure when exactlt this happend, it may have been after i downloaded an iTunes update, but I cant be sure. Other than that nothing else has really changed. I have now had this problem for a couple of weeks.
    I am running windows Vista (32 bit System)on my HP Laptop and have ADSL and am able to run explorer and all other non-apple software.
    I have tried all other advice offerd in the various supports:
    1. re-installed iTunes
    2. Checked all firewall settings - even removed Norton security (currently just operating on windows Visat security and have checked all that)
    3. changed "host" file to "back-host"
    4. played around and tested various internet settings
    I hope this information helps to solve the problem. I have also recently found some other information which may be useful:
    Although I do not use "safari" as an internet explorer, this does not work on my system either. I have re-installed this to see if it helps but am still unable to connect to the apple store (home page) on safari. I have looked up the support site for safari but have thus far be unable to find any helpful information to solve the problem.
    Please help this is very frustrating...
    Many thanks in advance!

    Thanks Polydorus,
    I have run the entire diagnostics the results are as follows:
    Microsoft Windows Vista Home Edition (Build 6000)
    Hewlett-Packard HP Pavilion dv6700 Notebook PC
    iTunes 7.7.1.11
    QuickTime 7.5
    CD Driver 2.0.7.3
    CD Driver DLL 2.1.1.1
    Apple Mobile Device 2.0.1.5
    Bonjour 1.0.4.12 (118.4)
    iTunes Serial Number 1F42598E2F1661DA
    Current user is not an administrator.
    The current local date and time is 2008-08-02 23:08:07.
    iTunes is not running in safe mode.
    Video Display Information
    NVIDIA, NVIDIA GeForce 8400M GS
    ** External Plug-ins Information **
    No external plug-ins installed.
    ** Network Connectivity Tests **
    Network Adapter Information
    Adapter Name: {095C31B4-7DF1-4CFF-BE80-E22A33EE716D}
    Description: Intel(R) PRO/Wireless 3945ABG Network Connection
    IP Address: 0.0.0.0
    Subnet Mask: 0.0.0.0
    Default Gateway: 0.0.0.0
    DHCP Enabled: Yes
    DHCP Server:
    Lease Obtained: Thu Jan 01 07:00:00 1970
    Lease Expires: Thu Jan 01 07:00:00 1970
    DNS Servers:
    Adapter Name: {1B5B44DE-64F4-4B5D-A57D-C80CAB0342C6}
    Description: Realtek RTL8101E Family PCI-E Fast Ethernet NIC (NDIS 6.0)
    IP Address: 192.168.1.33
    Subnet Mask: 255.255.255.0
    Default Gateway: 192.168.1.1
    DHCP Enabled: Yes
    DHCP Server: 192.168.1.1
    Lease Obtained: Sat Aug 02 18:25:24 2008
    Lease Expires: Sun Aug 03 18:25:24 2008
    DNS Servers: 192.168.1.1
    192.168.1.1
    Active Connection: LAN Connection
    Connected: Yes
    Online: Yes
    Using Modem: No
    Using LAN: Yes
    Using Proxy: No
    SSL 3.0 Support: Enabled
    TLS 1.0 Support: Enabled
    Firewall Information
    Windows Firewall is on.
    iTunes is enabled in Windows Firewall.
    Connection attempt to Apple web site was unsuccessful.
    The network connection timed out.
    Connection attempt to iTunes Store was unsuccessful.
    The network connection timed out.
    Secure connection attempt to iTunes Store was unsuccessful.
    The network connection timed out.
    Secure connection attempt to iPhone activation server unsuccessful.
    The network connection timed out.
    Last successful store access was 2008-07-03 17:03:38.
    ** CD/DVD Drive Tests **
    No drivers in LowerFilters.
    UpperFilters: GEARAspiWDM (2.0.7.3),
    E: PIONEER DVDRW DVR-K17B, Rev 1.02
    Data or MP3 CD in drive.
    Found 1 songs on CD, playing time 37:21 on CDROM media.
    Track 1, start time 00:02:00
    Get drive speed succeeded.
    The drive CDR speeds are: 4 10 16 20 24.
    The drive CDRW speeds are: 4.
    The drive DVDR speeds are: 4.
    The drive DVDRW speeds are: 4.
    ** iPod/iPhone Connectivity Tests **
    iPodService 7.7.1.11 is currently running.
    iTunesHelper 7.7.1.11 is currently running.
    Apple Mobile Device service 2.1.29.0 is currently running.
    Universal Serial Bus Controllers:
    Intel(R) ICH8 Family USB Universal Host Controller - 2830. Device is working properly.
    Intel(R) ICH8 Family USB Universal Host Controller - 2831. Device is working properly.
    Intel(R) ICH8 Family USB Universal Host Controller - 2832. Device is working properly.
    Intel(R) ICH8 Family USB Universal Host Controller - 2834. Device is working properly.
    Intel(R) ICH8 Family USB Universal Host Controller - 2835. Device is working properly.
    Intel(R) ICH8 Family USB2 Enhanced Host Controller - 2836. Device is working properly.
    Intel(R) ICH8 Family USB2 Enhanced Host Controller - 283A. Device is working properly.
    FireWire (IEEE 1394) Host Controllers:
    RICOH OHCI Compliant IEEE 1394 Host Controller. Device is working properly.
    Most Recent Device Not Currently Connected:
    iPod classic running firmware version 1.1.2
    Serial Number: 8K742MT2YMV
    ** iPhone/iPod Touch Sync Tests **
    No iPhone or iPod found.
    Hope this helps. Looking forward to resolving the problem.

  • ITunes error message / "iTunes could not connect to the music store...

    The past week, I have been having problems connecting to the iTunes music store. I purchased my ipod in 10/05 and have had no problems until recently. I keep receiving the following error message:
    "iTunes could not connect to the music store. Network connection was refused. Make sure your network settings are correct & network connection is active, then try again."
    I went onto the website, and checked various things. I uninstalled and reinstalled iTunes and the software, checked to see if I have any firewalls (none), checked to see if I have Windows XP service pack 2 (I have 1), and contacted my ISP (AOL). Help! I have AOL 8.0 dial up, and have had service with them for a couple of years now, so that is not an issue. Per AOL, I tried uninstalling AOL adapter and restarting my computer, and also deleting cookies and deleting files/all offline content, defaulted my security settings (they were the same), and reset web settings. I have restarted my computer, but am still having the same issues. I already contacted iTunes about this issue, and they sent me the same email twice, with the same instructions as their website, which I indicated I already tried numerous times. I have also checked my connections, and everything is fune. I try to access iTunes after logging into AOL.
    Thank you in advance to everybody that responds.
    Emily

    Thanks for the input. Unfortunately, I keep trying to do that, and have not been able to download for about a week. After contact customer support, I received the general "technical support" email, which is the same information found on the website. After replying to the email, which stated that I tried already tried the methods listed, I received the same email again. After replying to that email which included the previous threads, I received an email stating that the deparment I replied to does not handle technical issues. So, tonight, I re-emailed them with all of the threads and asked for an explanation of why I received technical emails if they do not respond to technical emails. It will be interesting to see how they respond, although it will probably be some general email. I sometimes respond to member service emails at my place of employment, so I know the procedure. The bottom line is that I should receive answers to my questions, even if the answer is something along these lines:
    "I am researching your problem, and will contact you within the next xx hours/business days with a resolution. We value you as a customer, and strive to maintain excellent customer support and satisfaction. Thank you for your patience."
    Or, a similar response. I know there is a general response library. And, I also know that if some body is unable to answer a question, as customer support, they should try utilize their resources. Basically, be a problem solver.

  • EAS server error: Could not connect to administration Server

    Hi,
    I have installed Hyperion suite in Windows server 2008 R2. It was working fine but now when i tried to login in to the EAS console, I am getting the following error:
    "Server Error: Could not connect to administration server".
    I tried accessing the same through the web URL and I found "404 error - file or directory not found".
    I verified all my services are up and running fine. I am able to connect to the essbase sever through Excel as well as planning.
    The log retireved from the HyS9eas-sysout.log file is below:
    <Sep 11, 2013 7:06:56 AM JST> <Info> <Security> <BEA-090905> <Disabling CryptoJ JCE Provider self-integrity check for better startup performance. To enable this check, specify -Dweblogic.security.allowCryptoJDefaultJCEVerification=true>
    <Sep 11, 2013 7:06:57 AM JST> <Info> <Security> <BEA-090906> <Changing the default Random Number Generator in RSA CryptoJ from ECDRBG to FIPS186PRNG. To disable this change, specify -Dweblogic.security.allowCryptoJDefaultPRNG=true>
    <Sep 11, 2013 7:06:58 AM JST> <Info> <WebLogicServer> <BEA-000377> <Starting WebLogic Server with Oracle JRockit(R) Version R28.0.2-11-135406-1.6.0_20-20100624-2119-windows-x86_64 from Oracle Corporation>
    <Sep 11, 2013 7:07:04 AM JST> <Info> <Management> <BEA-141107> <Version: WebLogic Server 10.3.4.0  Fri Dec 17 20:47:33 PST 2010 1384255 >
    <Sep 11, 2013 7:07:15 AM JST> <Emergency> <Management> <BEA-141151> <The admin server could not be reached at http://localhost:7001.>
    <Sep 11, 2013 7:07:15 AM JST> <Info> <Configuration Management> <BEA-150018> <This server is being started in managed server independence mode in the absence of the admin server.>
    <Sep 11, 2013 7:07:15 AM JST> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STARTING>
    <Sep 11, 2013 7:07:15 AM JST> <Info> <WorkManager> <BEA-002900> <Initializing self-tuning thread pool>
    <Sep 11, 2013 7:07:16 AM JST> <Notice> <LoggingService> <BEA-320400> <The log file E:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\EssbaseAdminServices0\logs\EssbaseAdminServices0.log will be rotated. Reopen the log file if tailing has stopped. This can happen on some platforms like Windows.>
    <Sep 11, 2013 7:07:16 AM JST> <Notice> <LoggingService> <BEA-320401> <The log file has been rotated to E:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\EssbaseAdminServices0\logs\EssbaseAdminServices0.log00410. Log messages will continue to be logged in E:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\EssbaseAdminServices0\logs\EssbaseAdminServices0.log.>
    <Sep 11, 2013 7:07:16 AM JST> <Notice> <Log Management> <BEA-170019> <The server log file E:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\EssbaseAdminServices0\logs\EssbaseAdminServices0.log is opened. All server side log events will be written to this file.>
    <Sep 11, 2013 7:07:48 AM JST> <Notice> <Security> <BEA-090082> <Security initializing using security realm myrealm.>
    <Sep 11, 2013 7:07:56 AM JST> <Warning> <JTA> <BEA-110503> <The migrator(the AdminServer for manual JTA migration policy, or the Singleton Master for automatic JTA migration policy) is not available. Will skip JTA TRS failback because isStrictOwnershipCheck is [false]. This may lead to potencial TLOG corruption if TRS of EssbaseAdminServices0 has been migrated to backup server and the backup server is accessing the TLOG of EssbaseAdminServices0. More safety can be achieved by setting isStrictOwnershipCheck to [true].>
    <Sep 11, 2013 7:08:35 AM JST> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STANDBY>
    <Sep 11, 2013 7:08:35 AM JST> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STARTING>
    Calling getConnection()
      return weblogic.management.jmx.mbeanserver.WLSMBeanServer@9830ac
    Calling getDomainConfiguration()
    Calling getConnection()
      return weblogic.management.jmx.mbeanserver.WLSMBeanServer@9830ac
    Calling getRuntimeService()
    Calling getConnection()
      return weblogic.management.jmx.mbeanserver.WLSMBeanServer@9830ac
      return com.bea:Name=RuntimeService,Type=weblogic.management.mbeanservers.runtime.RuntimeServiceMBean
      return com.bea:Name=EPMSystem,Type=Domain
    Calling getConnection()
      return weblogic.management.jmx.mbeanserver.WLSMBeanServer@9830ac
    Domain location is 'E:\Oracle\Middleware\user_projects\domains\EPMSystem'
    Calling getRuntimeService()
      return com.bea:Name=RuntimeService,Type=weblogic.management.mbeanservers.runtime.RuntimeServiceMBean
    Calling getConnection()
      return weblogic.management.jmx.mbeanserver.WLSMBeanServer@9830ac
    Calling getConnection()
      return weblogic.management.jmx.mbeanserver.WLSMBeanServer@9830ac
    Calling getConnection()
      return weblogic.management.jmx.mbeanserver.WLSMBeanServer@9830ac
    Calling getConnection()
      return weblogic.management.jmx.mbeanserver.WLSMBeanServer@9830ac
    Checking E:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\EssbaseAdminServices0\registry_update.xml file
    EPM_ORACLE_HOME: E:\Oracle\Middleware\EPMSystem11R1
    Template for EAS#11.1.2.0: E:\Oracle\Middleware\EPMSystem11R1\common\templates\applications\epm_eas_11.1.2.1.jar
    Dependencies for E:\Oracle\Middleware\EPMSystem11R1\common\templates\applications\epm_eas_11.1.2.1.jar: [Oracle EPM Common, Oracle EPM Calcmgr, Oracle EPM Planning libraries, Oracle EPM EAS libraries, Oracle EPM Misc libraries, Oracle EPM Xerces libraries]
    BPMUI shared webapp not referenced from EAS#11.1.2.0
    Application name: EAS#11.1.2.0
    Application source: eas.ear
    Server name: EssbaseAdminServices0
    Server port: 10080
    Server SSL port: 10083
    Application context: eas
    Registry product type: ESSBASE_PRODUCT
    Registry physical web application type: ADMIN_SERVICES_WEB_APP
    weblogic.Name property is 'EssbaseAdminServices0', seems to be WebLogic mode
    registry.isRegistryDatabaseCreated()true
    Registry was initialized sucessfully
    Executing pre custom update for EAS#11.1.2.0
    EPM_ORACLE_INSTANCE: E:\Oracle\Middleware\user_projects\epmsystem1
    <Sep 11, 2013 7:09:06 AM JST> <Error> <Deployer> <BEA-149205> <Failed to initialize the application 'EAS [Version=11.1.2.0]' due to error java.lang.NullPointerException.
    java.lang.NullPointerException
    at java.io.File.<init>(File.java:222)
    at com.hyperion.hit.tool.deploy.update.util.RegistryHelper.createPhysicalWebApp(RegistryHelper.java:168)
    at com.hyperion.hit.tool.deploy.update.RegistryUpdater.update(RegistryUpdater.java:36)
    at com.hyperion.hit.tool.deploy.update.RegistryUpdateListener.preStart(RegistryUpdateListener.java:91)
    at weblogic.application.internal.flow.BaseLifecycleFlow$PreStartAction.run(BaseLifecycleFlow.java:282)
    Truncated. see log file for complete stacktrace
    Caused By: java.lang.NullPointerException
    at java.io.File.<init>(File.java:222)
    at com.hyperion.hit.tool.deploy.update.util.RegistryHelper.createPhysicalWebApp(RegistryHelper.java:168)
    at com.hyperion.hit.tool.deploy.update.RegistryUpdater.update(RegistryUpdater.java:36)
    at com.hyperion.hit.tool.deploy.update.RegistryUpdateListener.preStart(RegistryUpdateListener.java:91)
    at weblogic.application.internal.flow.BaseLifecycleFlow$PreStartAction.run(BaseLifecycleFlow.java:282)
    Truncated. see log file for complete stacktrace
    >
    <Sep 11, 2013 7:09:06 AM JST> <Emergency> <Deployer> <BEA-149259> <Server 'EssbaseAdminServices0' in cluster 'EssbaseAdminServices' is being brought up in administration state due to failed deployments.>
    <Sep 11, 2013 7:09:17 AM JST> <Notice> <Cluster> <BEA-000197> <Listening for announcements from cluster using unicast cluster messaging>
    <Sep 11, 2013 7:09:17 AM JST> <Notice> <Cluster> <BEA-000133> <Waiting to synchronize with other running members of EssbaseAdminServices.>
    <Sep 11, 2013 7:09:22 AM JST> <Warning> <Log Management> <BEA-170011> <The LogBroadcaster on this server failed to broadcast log messages to the admin server. The Admin server may not be running. Message broadcasts to the admin server will be disabled.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090171> <Loading the identity certificate and private key stored under the alias DemoIdentity from the jks keystore file E:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\DemoIdentity.jks.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090169> <Loading trusted certificates from the jks keystore file E:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\DemoTrust.jks.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090169> <Loading trusted certificates from the jks keystore file E:\Oracle\Middleware\jrockit_160_20\jre\lib\security\cacerts.>
    <Sep 11, 2013 7:09:48 AM JST> <Alert> <Security> <BEA-090152> <Demo trusted CA certificate is being used in production mode: [
      Version: V3
      Subject: CN=CACERT, OU=FOR TESTING ONLY, O=MyOrganization, L=MyTown, ST=MyState, C=US
      Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
      Key:  Sun RSA public key, 512 bits
      modulus: 9550192877869244258838480703390456015046425375252278279190673063544122510925482179963329236052146047356415957587628011282484772458983977898996276815440753
      public exponent: 65537
      Validity: [From: Fri Mar 22 05:12:27 JST 2002,
                   To: Wed Mar 23 05:12:27 JST 2022]
      Issuer: CN=CACERT, OU=FOR TESTING ONLY, O=MyOrganization, L=MyTown, ST=MyState, C=US
      SerialNumber: [    33f10648 fcde0deb 4199921f d64537f4]
    Certificate Extensions: 1
    [1]: ObjectId: 2.5.29.15 Criticality=true
    KeyUsage [
      Key_CertSign
      Algorithm: [MD5withRSA]
      Signature:
    0000: 9D 26 4C 29 C8 91 C3 A7   06 C3 24 6F AE B4 F8 82  .&L)......$o....
    0010: 80 4D AA CB 7C 79 46 84   81 C4 66 95 F4 1E D8 C4  .M...yF...f.....
    0020: E9 B7 D9 7C E2 23 33 A4   B7 21 E0 AA 54 2B 4A FF  .....#3..!..T+J.
    0030: CB 21 20 88 81 21 DB AC   90 54 D8 7D 79 63 23 3C  .! ..!...T..yc#<
    ] The system is vulnerable to security attacks, since it trusts certificates signed by the demo trusted CA.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=thawte Primary Root CA - G3,OU=(c) 2008 thawte\, Inc. - For authorized use only,OU=Certification Services Division,O=thawte\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 2,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GlobalSign,O=GlobalSign,OU=GlobalSign Root CA - R3". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "OU=Security Communication RootCA2,O=SECOM Trust Systems CO.\,LTD.,C=JP". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=VeriSign Universal Root Certification Authority,OU=(c) 2008 VeriSign\, Inc. - For authorized use only,OU=VeriSign Trust Network,O=VeriSign\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=KEYNECTIS ROOT CA,OU=ROOT,O=KEYNECTIS,C=FR". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GeoTrust Primary Certification Authority - G3,OU=(c) 2008 GeoTrust Inc. - For authorized use only,O=GeoTrust Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "Default[6]" is now listening on 127.0.0.1:10080 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[6]" is now listening on 127.0.0.1:10083 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "Default[7]" is now listening on 0:0:0:0:0:0:0:1:10080 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[7]" is now listening on 0:0:0:0:0:0:0:1:10083 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "Default[3]" is now listening on fe80:0:0:0:0:5efe:a0e:daee:10080 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "Default[1]" is now listening on 10.14.126.11:10080 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[5]" is now listening on fe80:0:0:0:0:5efe:a0e:224b:10083 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[3]" is now listening on fe80:0:0:0:0:5efe:a0e:daee:10083 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[1]" is now listening on 10.14.126.11:10083 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "Default[5]" is now listening on fe80:0:0:0:0:5efe:a0e:224b:10080 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "Default[2]" is now listening on 10.14.34.75:10080 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[4]" is now listening on fe80:0:0:0:0:5efe:a0e:7e0b:10083 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure" is now listening on 10.14.218.238:10083 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "Default" is now listening on 10.14.218.238:10080 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[2]" is now listening on 10.14.34.75:10083 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <Server> <BEA-002613> <Channel "Default[4]" is now listening on fe80:0:0:0:0:5efe:a0e:7e0b:10080 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
    <Sep 11, 2013 7:09:48 AM JST> <Notice> <WebLogicServer> <BEA-000358> <Started WebLogic Independent Managed Server "EssbaseAdminServices0" for domain "EPMSystem" running in Production Mode>
    <Sep 11, 2013 7:09:48 AM JST> <Warning> <JMX> <BEA-149510> <Unable to establish JMX Connectivity with the Adminstration Server AdminServer at <JMXServiceURL:null>.>
    <Sep 11, 2013 7:09:48 AM JST> <Warning> <Server> <BEA-002611> <Hostname "SJ015040", maps to multiple IP addresses: 10.14.126.11, 10.14.34.75, 10.14.218.238, 0:0:0:0:0:0:0:1>
    <Sep 11, 2013 7:09:53 AM JST> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to ADMIN>
    <Sep 11, 2013 7:09:53 AM JST> <Notice> <WebLogicServer> <BEA-000360> <Server started in ADMIN mode>
    HyS9eas-syserr.log is empty and I dont find anyother details from the other log files.
    Kindly help me out in solving this issue.
    Thanks in advance.
    Regards,
    Balaji P

    Hi John,
    Sorry for replying late.
    I ran the EPM diagnostic and found EAS & APS application are failed. So as you mentioned, i tried re-deployment through EPM configurator.
    But Re-configuration fails with error "An unexpected error occurred and the application will have to shut down" .
    When i looked in to the Config tool.log,I got the following messages.
    [2013-09-17T18:17:04.635+09:00] [EPMCFG] [TRACE] [EPMCFG-01001] [oracle.EPMCFG] [tid: 17] [ecid: 0000K4fDMY^0zkgpxC^AyW1IE1pJ000003,0:325] [SRC_CLASS: com.hyperion.hit.tool.deploy.utils.UIPortUtil] trace: Parsing server FinancialReporting0 on port 8200 from registry
    [2013-09-17T18:17:04.827+09:00] [EPMINS] [ERROR] [EPMINS-00001] [oracle.EPMINS] [tid: 17] [ecid: 0000K4fDMY^0zkgpxC^AyW1IE1pJ000003,0:325] [SRC_CLASS: com.hyperion.hit.wizard.Wizard] trace: Unexpected error:[[
    java.lang.NullPointerException
    at com.hyperion.hit.tool.deploy.utils.UIPortUtil.<init>(UIPortUtil.java:83)
    at com.hyperion.hit.tool.deploy.utils.UIPortUtil.getInstance(UIPortUtil.java:53)
    at com.hyperion.config.wizard.DeploymentField.getAppServerDeploymentData(DeploymentField.java:235)
    at com.hyperion.config.wizard.DeploymentField.<init>(DeploymentField.java:56)
    at com.hyperion.config.wizard.impl.DeploymentForm.<init>(DeploymentForm.java:57)
    at com.hyperion.config.wizard.impl.DeploymentState.initializeBeforeShowOnNext(DeploymentState.java:56)
    at com.hyperion.hit.wizard.Wizard$NextClass.run(Wizard.java:522)
    at java.lang.Thread.run(Thread.java:619)
    Since it is similare to the Oracle konwledge base article - (Doc ID 1570293.1), I tried adding the shared service domain to the Windows host file. But i am still recieveing the same error message as above.
    Appreciates your help.
    Thanks & Regards,
    Balaji P

  • Itunes could not connect to iTunes Store-Network timed out. Upgraded to 7.6

    I upgraded this morning and was able to buy tracks. Now I get "Itunes could not connect to iTunes Store.The Network connection timed out. Running Nework Connectivity Test shows everything ok. Apple Sw Update application shows the same behavior. All of my other applications and programs run normally. I can surf web ok.
    Can someone help me?

    Search the forums. This is an old problem. For almost everyone it's a Norton issue. I had to upgrade from Norton 360 V1 to V2 to solve the problem. With otehr versions of Norton people have been able to create an entry in the firewall's allowed sites and that fixed it. If nothing else call Norton. They should have had enough calls by now they'll be able to tell you how to fix it for your version of Norton.

  • I can't connect to the router in my home.  Things were working fine as usual - I attended school and connected to their WiFi network as usual.  When I returned home I could not connect to my own home router.  The Ipad seeks the network but nothing happens

    I can't connect to the router in my home.  The Ipad seeks the network but nothing happens.  I went to school and connected to their WiFi network as usual with no problems.  When I returned home I could not connect to my home router.  The Ipad seeks the router number but nothing happens.  I rebooted the Ipad a few times in the school.  The numbers identifying the router, etc. on my Ipad no longer appear there. 
    TThe Ipad guide says to connect to the WiFi use setup but I can't find the setup program in the Ipad.
    I reset the network settings to the factory defaults but this doesn't fix the problem.
    What can I do to reconnect to my home router?

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • The MOF Compiler could not connect with the WMI server

    I am trying to add node2 to SQL  cluster (2008)  However, I kept running into errors with the following error message:
    "The MOF Compiler could not connect with the WMI Server. This is either because of a semantic error such as an incompatibility with the existing WMI repository or an actual error such as the failure of the WMI Server to start".
    I checked on the WMI services, they are started and running.renamed the WMI repository.  but nothing worked .
    Any idea what settings I need to change in order to ensure a successful instalation and add node 2 to sql cluster.

    Hi,
    Did SQL Server failed during installation and you somehow brought services online. Or it failed and next time you executed it succeeded IMO this error pops up because of remnants of failed installation on Node 1. With cluster specially if Installation on
    node 1 fails you should uninstall completely and remove all files related to SQL Server and then proceed.
    Have a look at below connect,see workaround and information posted by MS
    https://connect.microsoft.com/SQLServer/feedback/details/356258/the-mof-compiler-could-not-connect-with-the-wmi-server
    If above still not helps please post complete setup log file
    %Program files%\Microsoft sql server\100\Setup bootstrap\Log\ folder.
    Please mark this reply as answer if it solved your issue or vote as helpful if it helped so that other forum members can benefit from it.
    My TechNet Wiki Articles

Maybe you are looking for