[SOLVED] LVM Volume Groups Not Found

Hi,
I'm installing Arch on my desktop following the installation in the software raid and LVM section (https://wiki.archlinux.org/index.php/So … ID_and_LVM). I'm using RAID1. I've followed the important instructions on the LVM page (https://wiki.archlinux.org/index.php/LVM#Important). I have a UEFI motherboard so I created a separate boot partition and installed grub2 as my bootloader based on the instructions on the UEFI page (https://wiki.archlinux.org/index.php/Un … _Interface).
After a few hiccups, I think I have the system installed properly on my hard drive. Since the root partition is on the LVM, it needs to be loaded up pretty early in the boot process and this is where I'm getting a really strange issue. I have my motherboard configured to boot straight into the built-in UEFI shell. From here, I select the filesystem for my hard drive and launch grubx64.efi. So far so good. Now here's the weird part - if the LiveCD I used to install Arch is in the optical drive then everything boots up just fine, I get a prompt and I can log in and generally do as I see fit. But if the LiveCD isn't in the drive, then after I select the Arch Linux option in GRUB I get a message that says No Volume Groups found and dumps me into the rootfs shell.
As far as I can tell the LiveCD isn't actually being used during boot, but I don't understand why taking it out stops my logical volumes from loading =_=. Does anyone have some idea what's wrong / what I can do to fix it? Is there some config file that has been messed up? This is my second time trying this installation, if it doesn't work I'm just going to drop LVM and stick to just the software RAID. I'm not particularly attached to LVM, I decided to use it mainly because I could (or at least I thought I could).
Any help would be much appreciated. If there is any extra information I need to post, I can do that as well.
Update: It doesn't seem like the Arch LiveCD itself has anything to do with this. I inserted a blank CD and was able to boot up just fine but as soon as I took it out, I got the No volume groups found error again. This makes me think that it is a timing issue. Maybe one of the modules is not fully loaded before it is needed? Where can I go to find out what modules those are? Is there any way to force the boot process to wait until all the necessary modules are loaded?
SOLUTION: https://bbs.archlinux.org/viewtopic.php?id=145714
Last edited by jynnantonix (2012-09-07 19:30:01)

What you did has zero effect on the runtime order of the hooks (lsinitcpio would have shown you this).
https://bbs.archlinux.org/viewtopic.php?id=145714

Similar Messages

No automatic updation for IT0008. Allowance Grouping not found.

Hi
Guys whenever i am saving any employees 0581 it by giving metro,city allowances information in PA 30 i am getting the message "No automatic updation for IT0008. Allowance Grouping not found".
Can anybody tell what the reason behind it?
Regards
Surajit

Hi Sikindar,
Request you to let me know, if in table V_512W_D, in the cumulations column 14-HRA Basis, if there should be a check for wage type M230.
Would this solve the problem of automatic updation on infotype 0008??
Priority:HIGH
Thanks in advance,
Regards,
Angel

Error "No automatic updation for IT0008. Allowance Grouping not found"

I am maintaining IT581 of an employee.but system throws an error -->No automatic updation for IT0008. Allowance Grouping not found.I have maintained allowance grouping properly.The thing is my requirement is that i am maintening pay groups and level in table T710 instead of T510.Not touched T510.
Means i have also created IT1005(Planned compensation) in OM.Every other thing is ok.Except IT581.
What i beleive is its taking assignement from table V_T7INA3.where i am not able to store ESG for CAP, groups and levels.Because its taking value from T510.But i want to do everything on basis of pay scale grade ie T710.
Need your help and inputs....

Dear Sumo,
Kindly update feature 40 ECC which will help to automatic open the IT0008 for autmatic updation of such wagetypes ex: HRA
you can maintain percentage their for the particular wagetype for
40ECS - HR-IN : Feature to Determine Elgibility for RAPS
This feature is used to determine the factor which is multiplied with
the Reimbursement, Allowance or Perk (RAP) amount to calculate the
amount payable to the employee.
rocedure
The factor can be arrived at by making a decision on the following
details:
Country Grouping
Company Code
Payscale Grouping for Allowances
Wage Type
Gender Key
Number of children for children education allowance
Number of children for children hostel allowance
Personnel Number
ample
As per company A's policy, all employees belonging to the Payscale
Grouping for Allowance MN01, receive twice the amount eligible for
Childrens' Education Allowance (wagetype M260) in case the employee has
two or more children.
1           D   MOLGA
2   **          &ELIAL=1
3   40      D   LGART
4   40 ****     &ELIAL=1
5   40 M260 D   CEANO
6   40 M260 *   &ELIAL=2
7   40 M260 1   &ELIAL=1
kindly update the same and let me know.
rgds,
priyanka

ADAggregationManager::GetNestedParents() -- Mapped group not found in graph

Hi,
I am new to Crystal Reoprts.
We are getting errors in the same package. Users are getting authenticated OK, but we are unable to retrieve their privileges, Crystal Reports (V2.5) should be displayed based on AD groups they belong to.
CMS logs show,
[Wed May 28 15:20:45 2014]
2288
5256
assert failure: (Y:\authentication\WindowsADAuthen\ADAggregationManager.cpp:1143). (0 : WINAD: ADAggregationManager::GetNestedParents() -- Mapped group not found in graph!).
[Wed May 28 15:20:45 2014]
2288
5216
assert failure: (Y:\authentication\WindowsADAuthen\ADAggregationManager.cpp:1143). (0 : WINAD: ADAggregationManager::GetNestedParents() -- Mapped group not found in graph!).
[Wed May 28 15:20:45 2014]
2288
5256
assert failure: (Y:\authentication\WindowsADAuthen\ADAggregationManager.cpp:1143). (0 : WINAD: ADAggregationManager::GetNestedParents() -- Mapped group not found in graph!).
Any help really appreciated.

That helps a bit more. CE 10 is end of life a long time ago.
You can get the SDK help files for current versions from here:
help.sap.com
I don't believe the API's have changed for this part so use the SDK helpfile for more info.
You may be able to find examples here:
Crystal Reports for .NET SDK Samples - Business Intelligence (BusinessObjects) - SCN Wiki
Don

[SOLVED] Volume groups not showing up after update

nunikasi wrote:
Hello!
I run a arch linux setup with LVM volumes on a LUKS encrypted drive /dev/sda. The header resides in the initramfs-linux-ck.img (So kernel and header are on a USB stick and my hard drive is completely encrypted).
Everything worked nicely with this setup until today. I ran a
pacman -Syu
and the kernel was updated as normal and made a new initramfs-linux-ck.img on the usb stick (mounted in /boot). This is the way I always updated the kernel, and it always worked, but for some reason, after the reboot, and after typing my passphrase I got an error
ERROR: device '/dev/mapper/nunikasi-root' not found. Skipping fsck.
This was strange, so I booted the latest arch live-cd and did a
cryptsetup luksOpen /dev/sda nunikasi --header (pathToHeaderFile)
and entered the passphrase and still there are no volume groups in /dev/mapper. Am I wrong in thinking that this command should load my volume groups as
/dev/mapper/nunikasi-root
and
/dev/mapper/nunikasi-home
Running
vgscan
also reports no volume groups.
Additional information:
Last time I updated the kernel was around 24th of June.
I did run pacman -r linux before the update, assuming there is no need for it since I run linux-ck. I hope this is not relevant.
Do you know what went wrong?
What was the problem?
As I saw that dm-crypt had a problem with finding my logical volumes, I fired up
cryptsetup luksOpen /dev/sda nunikasi --header (pathToHeaderFile)
dhex /dev/mapper/nunikasi
and found that the lvm metadata was cut in half. So I ran
dhex /dev/mapper/nunikasi /dev/sda
and quickly saw that there was an attempt to make a MBR on /dev/sda (I saw the boot signature 55 aa on offset 1FE-1FF). I remembered that I tried to use GParted some days earlier to format a memory stick, and I probably forgot to change from /dev/sda before creating a MBR. This is most probably what happened, and now I had to restore the metadata in some way.
What was the solution?
As I had never made a backup of the metadata, I knew that LVM makes one for you and puts it in /etc/lvm/backup/. So I fired up dhex on /dev/mapper/nunikasi and searched for it. Found the offset and did:
dd if=/dev/mapper/nunikasi count=2148 skip=8928722944 of=lvm-metadata.txt iflag=skip_bytes,count_bytes
Now I had the metadata backup and the right UUID for my physical volume. Only steps left were:
pvcreate -ff -u [UUID] —restorefile lvm-metadata.txt /dev/mapper/nunikasi
vgcfgrestore -f lvm-metadata.txt nunikasi
vgchange -ay
And my setup is working again!
Have a nice day,
nunikasi
Last edited by nunikasi (2014-07-07 20:30:16)

nunikasi wrote:
clfarron4 wrote:Hmm... Have you tried breaking out an Arch installation disk and having a look with that?
Yes, I wrote that in the original post.
Sorry about that. I've just read it again.
OK, based on the information you've given us (LVM on LUKS, VG=nunikasi and LVs=root,home, backed up header), I would have thought that the commands you issued in your original post would have unlocked it. I'm not going to make any assumptions about the header of the actual LUKS partition though.
nunikasi wrote:I remember core/filesystems and some other core packages were updated.
I've had a look through my pacman.log and I can't think of anything that might upset it (that said, I am quite tired). I run 5 (maybe 6) different kernels (3.10, 3.12, 3.14 and 3.15 branches) and I haven't had any problems with finding PVs, VGs and LVs on either of my systems.
I'm at a loss as to what could be up right now and I'll this thread for tomorrow (because sleep beckons).
EDIT: Wow. That's quite something.
Last edited by clfarron4 (2014-07-08 11:21:46)

Error 15401: Windows NT user or group not found. Check the name again

when adding a windows login on SQL SERVER 2008 R2 below error is throwing
Windows NT user or group 'domain\user' not found. Check the name again.
I have gone through the link
http://support.microsoft.com/kb/324321/en-us &
http://support.microsoft.com/kb/2770837
collation setting of the instance is not case sensitive.

Hi DevXYZ,
Have you checked the other possible reasons for this issue?
The login does not exist
Verify that the Windows login still exists in the domain. Your network administrator may have removed the Windows login for specific reasons, and you may not be able to grant that login access
to the SQL Server.
Verify that you are spelling the domain and login name correctly and that you are using the following format:
Domain\User
If the login exists, and it is correct, and you still receive the error, continue with the following sections in this article.
Duplicate security identifiers
In a Windows domain, unique Security Identifiers (SIDs) are automatically assigned to Windows logins in the domain. When you add a Windows login as a SQL Server login, the SID is stored in a system table in SQL Server. If you try to add a new login which has
the same SID as an existing SQL Server login, the 15401 error occurs.
Authentication failure
You might receive error 15401 when the domain controller for the domain where the login resides (the same or a different domain) is not available for some reason.
If the login is in a different domain than the SQL Server, verify that the correct trusts exist between the domains.
Verify that the domain controller of the login is accessible by using the
ping command from the computer that is running SQL Server. Check both the IP address and the name of the domain controller.
After you tried all the possible methods list above, you still receive the same error, please check the error log as Dean Savović mentioned above and share us the detailed error message here
as we can analysis further.
Thanks
Candy Zhou

[SOLVED] version `HEIMDAL_KRB5_1.0' not found

Why is this happening now?
/opt/xbmc/share/xbmc/xbmc.bin: /usr/lib/libkrb5.so.25: version `HEIMDAL_KRB5_1.0' not found (required by /usr/lib/libsmbclient.so.0)
i did a
$ sudo pacman -Sy heimdal
it's up to date and installed, and i can't get rid of this message
Last edited by beatbreaker (2009-12-08 21:52:04)

Um, I have exact the same problem while starting some deamons (yestarday it was cups, but reinstalling heimdal solved it, today it's ssh), I have no packages ignored in pacman and I don't quite know what to do.
$ sudo /etc/rc.d/sshd start
:: Starting Secure Shell Daemon [BUSY]
/usr/sbin/sshd: /usr/lib/libkrb5.so.25: version `HEIMDAL_KRB5_1.0' not found (required by /usr/sbin/sshd)
[FAIL]
/EDIT: reinstalling openssh solved the problem, but still, I would like to know why pacman didn't upgrade ssh, as he should do this while pacman -Suy
Last edited by martusia (2009-12-14 19:56:10)

[SOLVED] 'sh: nano: command not found' on installation in arch-chroot

Hello,
I'm trying to install Arch Linux on a new laptop with a UEFI motherboard, however while following the beginners' guide on the step which requires you to arch-chroot into the /mnt base system to modify the locale.gen file using nano, I receive the following error:
'sh: nano: command not found'
I have mounted the partitions, installed the base system and have tried searching online for a solution but nothing seems to work. Also, nano works while outside of arch-root so I believe it is installed on my system.
I'm almost completely out of ideas on how to fix this, so any help or a point in the right direction would be greatly appreciated.
- Thanks.
Last edited by tyor (2013-01-20 12:01:54)

I had the same problem during my first attempts to install Arch. When you use the command as stated:
# pacstrap -i /mnt base base-devel
it seems not all packages were downloaded/installed. Now I know it was my own fault by not selecting the packages properly.
In the beginnersguide right above the pacstrap command is stated:
The -i switch can be omitted if you wish to install every package from the base and base-devel groups without prompting.
So I did, and installed without a problem

[solved]lvm volumes no longer auto mount after update to systemd 210-2

Note: I don't have an initramfs, it's a statically compiled kernel. I can get machine to boot if I manually mount all lvm volumes by hand. Thankfully my root was not on the lvm. fstab is as follows :
tmpfs /tmp tmpfs nodev,noatime,nosuid 0 0
LABEL=dump /dump ext4 defaults,noatime 0 1
LABEL=home /home ext4 defaults,noatime,discard,user_xattr 0 1
LABEL=root / ext4 defaults,noatime,discard 0 1
LABEL=var /var ext4 defaults,noatime 0 1
LABEL=swap swap swap defaults 0 0
LABEL=local-compile /var/abs/local btrfs defaults,noatime 0 1
Do I need to make any changes to configuration somewhere for lvm ?
Last edited by anish (2014-03-05 12:15:42)

My guess is that this has nothing to do with LVM at all. See http://cgit.freedesktop.org/systemd/sys … d=v210#n39.

[Solved]PM: swap header not found attempting to suspend encrypted disk

Hi all,
I have my root partition set up as a dm-crypt encrypted volume, and I followed the instructions here to set up a swap file.
I also followed these instructions to add the resume hook to my mkinitcpio.conf between encrypt and filesystems.
I modified the /etc/default/grub file like so:
GRUB_CMDLINE_LINUX_DEFAULT="cryptdevice=/dev/disk/by-uuid/0cb6b266-ce81-4b2f-9958-722c788c46ef:cryptroot cryptkey=/dev/disk/by-uuid/18868ab9-e0dd-4634-9f9e-69f3d3686d3f:ext2:/laptopkey root=/dev/mapper/cryptroot resume=/dev/mapper/cryptroot resume_offset=4952064"
I determined the offset using the swap-offset tool provided by the uswsusp package.
And I ran
mkinitcpio -p linux
and
grub-mkconfig
When I type "systemctl hibernate" the system begins to hibernate, then comes back up immediately. Journalctl -xn gives this:
Jan 08 23:38:57 lefty-laptop systemd[1]: systemd-hibernate.service: main process exited, code=exited, status=1/FAILURE
Jan 08 23:38:57 lefty-laptop systemd[1]: Failed to start Hibernate.
-- Subject: Unit systemd-hibernate.service has failed
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/be02cf6855d2428ba40df7e9d022f03d
-- Unit systemd-hibernate.service has failed.
-- The result is failed.
Jan 08 23:38:57 lefty-laptop systemd[1]: Dependency failed for Hibernate.
-- Subject: Unit hibernate.target has failed
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/be02cf6855d2428ba40df7e9d022f03d
-- Unit hibernate.target has failed.
-- The result is dependency.
Jan 08 23:38:57 lefty-laptop systemd[1]: Service sleep.target is not needed anymore. Stopping.
Jan 08 23:38:57 lefty-laptop systemd[1]: Unit systemd-hibernate.service entered failed state.
Jan 08 23:38:57 lefty-laptop systemd[1]: Stopping Sleep.
-- Subject: Unit sleep.target has begun shutting down
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Unit sleep.target has begun shutting down.
Jan 08 23:38:57 lefty-laptop systemd[1]: Stopped target Sleep.
-- Subject: Unit sleep.target has finished shutting down
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/9d1aaa27d60140bd96365438aad20286
-- Unit sleep.target has finished shutting down.
Jan 08 23:38:58 lefty-laptop kernel: Freezing user space processes ... (elapsed 0.001 seconds) done.
Jan 08 23:38:57 lefty-laptop wpa_actiond[1017]: Interface 'wlan0' lost connection to network 'braains'
Jan 08 23:38:58 lefty-laptop kernel: PM: Marking nosave pages: [mem 0x0009d000-0x000fffff]
Jan 08 23:38:58 lefty-laptop kernel: PM: Basic memory bitmaps created
Jan 08 23:38:58 lefty-laptop kernel: PM: Preallocating image memory... done (allocated 294215 pages)
Jan 08 23:38:58 lefty-laptop kernel: PM: Allocated 1176860 kbytes in 0.22 seconds (5349.36 MB/s)
Jan 08 23:38:58 lefty-laptop kernel: Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Jan 08 23:38:58 lefty-laptop kernel: e1000e 0000:00:19.0: setting latency timer to 64
Then a bunch more stuff, then this:
Jan 08 23:38:58 lefty-laptop kernel: PM: thaw of devices complete after 955.701 msecs
Jan 08 23:38:58 lefty-laptop kernel: PM: writing image.
Jan 08 23:38:58 lefty-laptop kernel: PM: Using 1 thread(s) for compression.
PM: Compressing and saving image data (197765 pages)...
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 0%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 10%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 20%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 30%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 40%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 50%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 60%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 70%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 80%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 90%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving progress: 100%
Jan 08 23:38:58 lefty-laptop kernel: PM: Image saving done.
Jan 08 23:38:58 lefty-laptop kernel: PM: Wrote 791060 kbytes in 4.67 seconds (169.39 MB/s)
Jan 08 23:38:58 lefty-laptop kernel: PM: S
Jan 08 23:38:58 lefty-laptop kernel: PM: Swap header not found!
Jan 08 23:38:58 lefty-laptop kernel: |
Jan 08 23:38:58 lefty-laptop kernel: PM: Basic memory bitmaps freed
Jan 08 23:38:58 lefty-laptop kernel: Restarting tasks ... done.
Jan 08 23:38:58 lefty-laptop kernel: video LNXVIDEO:00: Restoring backlight state
Jan 08 23:38:58 lefty-laptop laptop-mode[28617]: Laptop mode
Jan 08 23:38:58 lefty-laptop laptop-mode[28618]: enabled, not active [unchanged]
Jan 08 23:38:58 lefty-laptop laptop-mode[28622]: Laptop mode
Jan 08 23:38:58 lefty-laptop laptop-mode[28623]: enabled, not active [unchanged]
Perhaps the "PM: swap header not found" is not the primary error?
Last edited by LeftyAce (2014-01-12 06:08:55)

LeftyAce wrote:
ROOKIE: which UUID do you use? If I list /dev/disk/by-uuid I get two results:
total 0
lrwxrwxrwx 1 root root 10 Jan 11 18:06 06f4c97e-fe09-45a8-a937-dedb6b18339b -> ../../dm-0
lrwxrwxrwx 1 root root 10 Jan 11 18:06 a0eb0a15-6d5d-4df2-a0d3-6f7fb00885c6 -> ../../sda1
I think one of them is the actual device, the other is the dm-crypt container? I guess I could try both...I'll report back.
Usually I use the output of blkid to find out the correct uuid. The uuid to use for / or swap is the one pointing to one of /dev/dm*.
LeftyAce wrote:For the record I am using resume=/dev/mapper/cryptroot. I think since the swapfile is a file not a block device in my case that's important. Since the encrypt hook runs first, that mapper volume is present and unlocked by the time resume comes around.
In my case the same happens but for some reason it doesn't seem to work, and I've been procrastinating submitting a bug (I use hibernation very rarely and I know of a way that works).

[SOLVED] Fatal: module phc_intel not found

I've used the phc_intel package from AUR, yet it didn't work for me and I removed it. Now, during boot I get the "Fatal: module phc_intel not found" message. It doesn't stop the boot but it's annoying. There is no mention of it in rc.conf:
MOD_AUTOLOAD="no"
#MOD_BLACKLIST=() #deprecated
MODULES=(!usblp acpi_cpufreq cpufreq_ondemand iwl4965 ac battery button processor thermal video btusb cdrom agpgart intel-agp nvram i2c-i801 i2c-core evdev joydev pcspkr psmouse serio_raw led-class mmc_core ricoh_mmc sdhci-pci sdhci pci_hotplug shpchp thinkpad_acpi wmi rtc-cmos rtc-core rtc-lib nvidia output iTCO_vendor_support iTCO_wdt snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-codec snd-hda-intel soundcore scsi_mod ahci ata_piix e1000e bluetooth mac80211 rfkill iwlagn iwlcore cfg80211 pcmcia_core rsrc_nonstatic yenta_socket usb-storage usbcore ehci-hcd uhci-hcd ieee1394 ohci1394 sd_mod sr_mod st)
Any ideas?
Last edited by dcc24 (2009-12-19 19:59:45)

Yes, there was a conf file there. Removing it solved the problem. Thanks!

Can't solve "valid signing identity not found" issue

Hello,
I'm having a lot of trouble getting an app to build properly. I'm using the Corona SDK, but I believe that my true problem lies here:
It says, "Valid signing identity not found."
I've gone through the process of uninstalling all of my Provisioning Profiles and reinstalling them numerous times but still haven't solved this issue. Any advice would be greatly appreciated.
Cheers,
- Bret

Hi etresoft,
Thanks so much for taking the time to reply to my question. I am under the assumption that my build issue has something to do with the "Valid signing identity not found." message that appears in the XCode Provisioning Profiles window. In all probability, this is causing my build issue, and it seems like a Provisioning / Keychain issue and not necessarily a Corona SDK issue. I did contact Corona anyhow and I'm waiting for a reply.
If there's any chance you can help me debug the "Valid signing identity not found", I would be very grateful!
Cheers,
- Bret

G5 Crashes, cannot reinstall as detination volume is not found

I have been experiencing problems with my G5 as follows:
1. computer freezes with spinning beach ball and will not respond, dock remains magnified.
2. Computer will switch off from power button only.
3. Computer will not reboot - grey screen and fan running high
4. Install disk cannot verify or repair hard drive volume due to error (underlying task reported failure on exit (-9972)
5. Tried to reinstall osx but the destination volume cannot be found.
6. Tried resetting pram and smu - no joy.
7. Disconnected power supply for some minutes - no joy.
8. Computer is left for hours and will reboot with no noticeble reason or pattern and will run for no specific time from 2 minutes to 3 days and will then freeze and we start all over again as above.
Please help
g5 Mac OS X (10.3.9) imac g5 20inch 1.8ghz 768 ram

Welcome To Discussions triggerz215!
That's not good. Your HD either has serious directory corruption, or is failing.
More info here Disk Utility reports "Underlying task reported failure" when repairing a volume.
And here are links to two Third-Party utilities, referred to in the article.
DiskWarrior
TechTool Pro
Instructions for How to use FireWire target disk mode, to backup your data.
Good Luck!
ali b

Logon group not found when launching planning workbench

When I start planning workbench in RSPLAN, the following error appears:
Connect to message server host failed Connect_PM TYPE=B MSHOST=bwdev.shdl.com GROUP=PUBLIC R3NAME=BWD MSSERV=sapmsBWD PCS=1 ERROR Group PUBLIC not found TIME Mon Sep 25 13:13:13 2006 RELEASE 700 COMPONENT LG VERSION 5 RC -6 MODULE lgxx.c LINE 4288 DETAIL LgIGroupX COUNTER 1
We filled group "PUBLIC" for template installer and it went through with all green lights including BI IP required 4 JCO desitinations.
but after having a look at the following threads Re: BIP in 2004s, I notice the following sentence: "3. Logon Group - Make sure logon group is specified in ABAP system (SMLG)", when I go to SMLG, only one record with empty logon group exists, but the status is green.
Shall I maintain anything in SMLG? create "public" group in SMLG?
need suggestion...
Patrick

Hi Gregor
I have already followed points with 919850, and our basis already setup SLD (for bw system in SLD, he setup two logon group: SPACE(default) and PUBLIC).
After I maintain logon group "PUBLIC" in SMLG, and then re-execute the step 14 (maintain 4 BI IP JCO destinations), 4 JCO destination appears with green lights again afterwards.
However, now the internl error 500 appears in the web.
any more suggestion?
Patrick

[SOLVED] network-manager-applet not found

Hi, I'm quite noob here, and I'm trying to install network-manager-applet with no luck;
So far I've done
# pacman -S network-manager-applet
and I got
resolving dependencies...
looking for inter-conflicts...
Targets (1): network-manager-applet-0.8-1
Total Download Size: 1.01 MB
Total Installed Size: 4.35 MB
Proceed with installation? [Y/n] y
:: Retrieving packages from extra...
error: failed retrieving file 'network-manager-applet-0.8-1-x86_64.pkg.tar.gz' from mi.mirror.garr.it : Not Found
error: failed retrieving file 'network-manager-applet-0.8-1-x86_64.pkg.tar.gz' from ftp.nluug.nl : Not Found
error: failed retrieving file 'network-manager-applet-0.8-1-x86_64.pkg.tar.gz' from ftp.hosteurope.de : Not Found
error: failed retrieving file 'network-manager-applet-0.8-1-x86_64.pkg.tar.gz' from ftp-stud.hs-esslingen.de : Not Found
error: failed retrieving file 'network-manager-applet-0.8-1-x86_64.pkg.tar.gz' from archlinux.puzzle.ch : Not Found
error: failed retrieving file 'network-manager-applet-0.8-1-x86_64.pkg.tar.gz' from ftp.surfnet.nl : Not Found
warning: failed to retrieve some files from extra
error: failed to commit transaction (Not Found)
Errors occurred, no packages were upgraded.
so I tried to download the package itself and install it with
pacman -U network-manager-applet-0.8-2-x86_64.pkg.tar.xz
and the answer was
loading package data...
checking dependencies...
error: failed to prepare transaction (could not satisfy dependencies)
:: network-manager-applet: requires mobile-broadband-provider-info
what to do?
i cannot find in the repos the package mobile-broadband-provider-info
thank you in advance
Last edited by lsk (2010-03-10 10:15:21)

Update your system - "pacman -Syu". The clue is that the file you manually downloaded is different to the one pacman is trying to get.

[SOLVED] LVM Volume Groups Not Found

Similar Messages

Maybe you are looking for