[SOLVED] Mirrorlist's error installing the base system

Hi!
I'm trying to install ArchLinux on my Acer Aspire 5750G (I'm following the "Beginners' Guide").
I managed to establish a Wi-Fi connection (Although "wifi-menu" didn't work: I used the wpa_supplicant function. But this isn't the purpose of the thread) and to mount the various partitions. But now I have some problems installing the base system.
Infact, when I go for:
pacstrap -i /mnt base
I get an error like:
error: failed retrieving file 'core.db' from archlinux.openlabto.org : Resolving timed out after 10463 milliseconds
And it continues like this for each mirror of the mirrorlist, so I think that they're not the problem.
And its not even a problem of my internet connection, because if I try the "ping" command it works.
I have to say that my iso is the "July" one, because when they released the last one I had already burnt mine to a DVD. Maybe that's way I get this error, but I'm note sure.
I've searched for some solutions on the forum, and someone said that after some time it should function.
Anyway, how can I resolve this issue?
Thanks in advance.
Last edited by Wantoast (2013-08-07 17:07:28)

drcouzelis wrote:The month old installation media shouldn't be a problem.
Definitely. I have just tried with the newest version and the problem occurred again.
drcouzelis wrote:
Does the Internet connection really work? Can you load a website in a web browser?
# Use links (or links2 or lynx, whatever's installed)
links archlinux.org
link will not execute and completion _links exsists.
EDIT: I used elinks and Internet works. I'm quite sure it's not a connection problem ("Quite" because if wifi-menu didn't work there should be a reason).
Last edited by Wantoast (2013-08-07 14:57:09)

Similar Messages

Question!hi!i try to install mac os x lion from 10.6.8. the system apprear the error message, the recover system can not be created . how should I do?

question!hi！i try to install mac os x lion from 10.6.8. the system apprear the error message, the recover system can not be created . how should I do?

Peruse the hits from a google search for recovery system can't be created site:apple.com

How do I re-install the operating system on my BlackBerry Torch 9800 - I am sure it is hacked.

Greetings,
Can someone point me to instructions on how to re-install the operating system on a BlackBerry Torch 9800 and then upgrade it to the latest release?
I have done this several times in the past, due to recurring hacking, but have lost the instructions.
Thank you very much for your help.
Regards,
Jean-Pierre
P.S. I would preffer a releas of the OS without any pre-install applicaitons such as Twitter, Facebook, LinkedIn,
and above all, Whastapp. Thank you.

Hi and Welcome to the Community!
The simplest way is to, on a PC (you cannot do this on MAC):
1) Make sure you have a current and complete backup of your BB...you can find complete instructions via the link in my auto-sig below.
2) Uninstall, from your PC, any BB OS packages
3) Make sure you have the BB Desktop Software already installed
http://us.blackberry.com/software/desktop.html
4) Download and install, to your PC, the BB OS package you desire:
http://us.blackberry.com/support/downloads/download_sites.jsp
It is sorted first by carrier -- so if all you want are the OS levels your carrier supports, your search will be quick. However, some carriers are much slower than others to release updates. To truly seek out the most up-to-date OS package for your BB, you must dig through and find all carriers that support your specific model BB, and then compare the OS levels that they support.
5) Delete, on your PC, all copies of VENDOR.XML...there will be at least one, and perhaps 2, and they will be located in or similarly to (it changes based on your Windows version) these folders:
C:\Program Files (x86)\Common Files\Research In Motion\AppLoader
C:\Users\(your Windows UserName)\AppData\Roaming\Research In Motion\BlackBerry\Loader XML
6a) For changing your installed BB OS level (upgrade or downgrade), you can launch the Desktop Software and connect your BB...the software should offer you the OS package you installed to your PC.
6b) Or, for reloading your currently installed BB OS level as well as for changing it, bypass the Desktop Software and use LOADER.EXE directly, by proceeding to step 2 in this process:
http://supportforums.blackberry.com/t5/BlackBerry-Device-Software/How-To-Reload-Your-Operating-Syste...
Note that while written for "reload" and the Storm, it can be used to upgrade, downgrade, or reload any BB device model -- it all depends on the OS package you download and install to your PC.
If, during the processes of 6a or 6b, your BB presents a "507" error, simply unplug the USB cord from the BB and re-insert it...don't do anything else...this should allow the install to continue.
If you are on MAC, you are limited to only your carriers sanctioned OS packages...but can still use any levels that they currently sanction. See this procedure:
KB19915How to perform a clean reload of BlackBerry smartphone application software using BlackBerry Desktop Software
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

VMWARE Server2012RT Installation failed with option: I will install the Operating System later

Hello, first sorry for my englich but I hope it wille ok for this Issue.
I have instelled the Win2012RT Server in VMware but the Installtion failed with this error:
Ok i chose the option: "I will install the Operating System later.",
and also tried
this:
http://www.techieshelp.com/server-2012-windows-cannot-read-the-setting-from-the-unattend-answer-file/
However, I always get
this displayed:
Last Log entry is this one:
2014-05-07T09:42:03.962+02:00| vmplayer| I120: VMMgr: Finished opening VM at /vm/#cf2324dcf779001d/ from G:\VMs\Server2012RTVmware.vmx
2014-05-07T09:42:03.962+02:00| vmplayer| I120: cui::MKSScreenWindowCoordinator::HandleGuestTopologyChange: main UI rect: 687x619 @ 948,249
2014-05-07T09:42:03.962+02:00| vmplayer| I120: cui::MKSScreenWindowCoordinator::HandleGuestTopologyChange: Found 0 present screens
2014-05-07T09:42:03.962+02:00| vmplayer| I120: cui::MKSScreenWindowCoordinator::HandleGuestTopologyChange: Windows for extra guest monitors will not be shown
2014-05-07T09:42:03.962+02:00| vmplayer| I120: cui::MKSScreenWindowCoordinator::HandleGuestTopologyChange: setting main view to all displays
2014-05-07T09:42:03.978+02:00| vmplayer| I120: SnapshotTree: Emitting refresh (G:\VMs\Server2012RTVmware.vmx)
2014-05-07T09:42:04.009+02:00| vmplayer| I120: VMHSVMCbPower: G:\VMs\Server2012RTVmware.vmx, Setting state of VM to powerOn with option soft
2014-05-07T09:42:04.024+02:00| vmplayer| I120: Stats VMX "G:\Programme2tePlatte\vmware-vmx-stats.exe" not found. Using standard VMX "G:\Programme2tePlatte\x64\vmware-vmx.exe"
2014-05-07T09:42:04.024+02:00| vmplayer| I120: Starting vmx as G:\Programme2tePlatte\x64\vmware-vmx.exe
2014-05-07T09:42:04.024+02:00| vmplayer| I120: Starting vmx as G:\Programme2tePlatte\x64\vmware-vmx.exe
2014-05-07T09:42:04.024+02:00| vmplayer| I120: VigorClient_StartAndConnect Failed: Message
2014-05-07T09:42:04.024+02:00| vmplayer| I120: G:\VMs\Server2012RTVmware.vmx: Pending power op found, completing.
2014-05-07T09:42:04.024+02:00| vmplayer| I120: G:\VMs\Server2012RTVmware.vmx: Clearing execReqPath
2014-05-07T09:42:04.024+02:00| vmplayer| I120: G:\VMs\Server2012RTVmware.vmx: Reloading config state.
2014-05-07T09:42:04.024+02:00| vmplayer| I120: VMHS: Transitioned vmx/execState/val to poweredOff
2014-05-07T09:42:04.040+02:00| vmplayer| I120: G:\VMs\Server2012RTVmware.vmx: VMHSStartVmxVigorCb: vmPath=/vm/#cf2324dcf779001d/ status=error
2014-05-07T09:42:04.040+02:00| vmplayer| I120: G:\VMs\Server2012RTVmware.vmx: Reloading config state.
2014-05-07T09:42:04.040+02:00| vmplayer| I120: VMHS: Transitioned vmx/execState/val to poweredOff
2014-05-07T09:42:04.040+02:00| vmplayer| I120: Setting power state poweredOff
2014-05-07T09:42:04.056+02:00| vmplayer| I120: Internal VMDB error: VMDB failure (-1)
2014-05-07T09:42:04.056+02:00| vmplayer| I120: VMMgr::CloseVM: closing VM at /vm/#cf2324dcf779001d/
2014-05-07T09:42:04.056+02:00| vmplayer| I120: DlgUI: Error while powering on: Internal error.
2014-05-07T09:42:04.087+02:00| vmplayer| I120: VMMgr::OnVMDestroyed: cleaning up after destroyed VM at /vm/#cf2324dcf779001d/
2014-05-07T09:42:04.087+02:00| vmplayer| I120: cui::MKS::SetAttached: detach
2014-05-07T09:42:04.087+02:00| vmplayer| I120: cui::MKS::OnSetAttachedCompleted
2014-05-07T09:42:04.118+02:00| vmplayer| I120: FILE: FileDeletionRetry: Non-retriable error encountered (C:\Users\Michael\AppData\Roaming\VMware\preferences.ini~): Unknown error 2 (0x2) (2)
2014-05-07T09:42:07.488+02:00| vmplayer| I120: PlayerFrame::UpdateActivePlayer: mActive=1
2014-05-07T09:42:09.874+02:00| vmplayer| I120: PlayerFrame::UpdateActivePlayer: mActive=0
2014-05-07T09:44:13.286+02:00| vmplayer| I120: PlayerFrame::UpdateActivePlayer: mActive=1
2014-05-07T09:44:13.473+02:00| vmplayer| I120: Cmd /host2/#_client/util/file/cmd/##135/op/stat/ failed: Invalid path
2014-05-07T09:44:17.061+02:00| vmplayer| I120: PlayerFrame::UpdateActivePlayer: mActive=0
Does anyone have
an idea maybe??
Vmware Version is: 6.0.2 build-1744117
Host: Windows 7 Enterprise, 64-bit 6.1.7601, Service Pack 1
WIN2012RT Iso is: 9600.17050.WINBLUE_REFRESH.140317-1640_X64FRE_SERVER_EVAL_DE-DE-IR3_SSS_X64FREE_DE-DE_DV9.ISO DOWNLOAD: http://technet.microsoft.com/de-de/evalcenter/dn205286.aspx

Ok. I could finde out the Problem.
I uninstalled VMware witht RevoUninstaller and deleted all Vmware sysfolders and all regKeys.
Important note:
The first Installtion was on the 2nd Hard disk on my PC. These Harddisk was Connected via USB3 Port. VMware was successfully installed, and via the standart installation procedure the ISO files could be installed in Vmware, but the problem persist with
WIN2012RT server.
After a new installation of VMware into the Local C: Drive. The Win2012RT.Iso could be installed. With this procedure
without Issues: http://www.techieshelp.com/server-2012-windows-cannot-read-the-setting-from-the-unattend-answer-file/
ISO Download: http://technet.microsoft.com/de-de/evalcenter/dn205286.aspx

There were errors installing the software

Mac Mini G4 1.25GHz / 512MB / 40GB / Combo / Modem.
Ser: YM6***TAB
<Edited by Moderator: Personal Info - Please See Terms of Use>
Originally Mum's Mini was "doing strange things", so I had to drive 150 miles to try to sort it out.
First I downloaded AppleJack and tried it out on my own G4 Tower before heading north to visit Mum. Applejack installed OK from my USB memory stick.
Unfortunately, it didn't occur to me to take a spare keyboard and I was unable to get her Mac Mini (with a miniature keyboard) to respond to any key presses at start-up, which foiled all attempts to use AppleJack or even single user mode!
However, I was able to use DiskWarrior and it found several corrupted files on the Hard Drive, which it claimed (after two attempts) were repaired. I then "repaired permissions" and ejected the DiskWarrior disc. Then I had the bright idea of going to "Software Update" in the Apple Menu. This downloaded the latest OS10.4.11 and started to install it. After 20 minutes it reported that there was a "problem with installation" and I should reboot and try again, which I did, with the same result. So then I had the amazingly bright idea of erasing the drive and installing 10.4 from the original DVD. This got several minutes into the procedure before reporting a problem. "There were problems installing the software".
I gave up at that point, left Mum my iBook to use and brought the Mac Mini home.
I was able to boot it up from an external Firewire HD, which contained a clone of the boot drive from my own G4 Mac Mini. It seemed to work OK so I tried the Tiger installation DVD again. It failed as before but I was able to save the Crash Log onto the Firewire Drive and you can view it here:
http://www.amstard.co.uk/temp/OSInstallCrashLog.txt
(I hope this means something to somebody! The way I interpret it is that it installed a file then discovered that file was corrupted?)
I used Prosoft "Drive Genius" to erase the internal Hard Drive again and it reported that all was well. But I still couldn't install the OS.
After that, I couldn't even get the Mac Mini to boot from the external Firewire drive. It just produces a black oblong on a gray screen with a stalled "cog wheel". Here's a photo that I took:
http://www.amstard.co.uk/temp/screenphoto.jpg
There is nothing connected except the standard USB keyboard and mouse at this point and the external Firewire drive.
It does boot up with the generic Tiger installation DVD. I can run Disk Utility, which reports no errors on the Hard Drive. But it fails when I try to install the OS 10.4 with an error message "There were problems installing the software" (generic OS10.4 installer) or "There were errors installing the software" (original Mac Mini OS10.4 installer).
I have fitted a new 120GB drive and replaced the RAM. The OS still fails to install on the newly formatted drive. The Apple site suggests a firmware update for this error message but doesn't list one for the Mini.
I have tried installing OS10.4 from the original Mac Mini installations discs and from a generic 10.4 installer. Both give the same "There were errors installing the software" message.
I have "zapped the PRAM" without making any difference to this symptom.
I have tried doing the simplest installation without any additional fonts, language translators or bundled software.
Any suggestions - apart from "scrap it!"?
Martin (UK)

It does boot up with the generic Tiger installation DVD. I can run Disk Utility, which reports no errors on the Hard Drive. But it fails when I try to install the OS 10.4 with an error message "There were problems installing the software" (generic OS10.4 installer) or "There were errors installing the software" (original Mac Mini OS10.4 installer).
I have fitted a new 120GB drive and replaced the RAM. The OS still fails to install on the newly formatted drive. The Apple site suggests a firmware update for this error message but doesn't list one for the Mini.
I have tried installing OS10.4 from the original Mac Mini installations discs and from a generic 10.4 installer. Both give the same "There were errors installing the software" message.
Since this is an original G4 mini, there is no reason at all that any full retail 10.4 installer, or the original MacOS installer that came with the mini would not work. Later minis, released after Tiger's release date were in some instances unable to boot from the early versions of the Tiger retail installer because 10.4.0 or 10.4.1 pre-dated the versions those minis came supplied with, but clearly that isn't the case with your system.
If you are certain that the MacOS install disk you have is the one that original one that came with the mini (which should be a late version of MacOS 10.3.x), then the only obvious thing to check is that you have correctly partitioned the drive (it should be partitioned in the Apple Partition Map scheme, and then formatted as MacOS Extended (Journalled). If those parameters are met and you continue to get the error from a valid installer for that system, then the potential causes narrow to such things as defective install disks (unlikely since you have tried more than one), defective optical drive unlikely because you can boot from the install disk using the drive), or defective logic board/disk controller - which is a distinct possibility since it's possible that was responsible for the first drive failure (or the indications of failure).
Boot the system using the original MacOS installer and using Disk Utility, set the new internal drive up again with the APM partitioning and MacOS Extended (Journalled) formatting, then immediately run the 'Repair Disk' tool on it to make sure the drive is being read and written correctly. Then performa PMU reset (instructions below) to ensure that the failure to boot from the external FW drive is not a simple matter of dropped FW port. On rebooting with your FW drive connected, hold the Option key down to see if the system then recognizes your external drive. If it does, select it and attempt to boot from it.
With luck that will give you a working system, booted from your external, at which point I would then see if it's possible to clone your external to the new internal drive, rather than attempt a reinstall from the MacOS installer.
On the face of it there should be no reason that would not work since by booting from the MacOS installer you basically show that the system is sound and the optical drive is working. By partitioning and formatting the internal drive and getting a clean bill of health from the repair disk tool, you show the drive and disk controller are OK. That doesn't leave much else to be at fault!

Re-installing Adobe Lightroom with cd software after re-installing the operating system?

i wiped my computer clean and re-installed the operating system on my macbook pro because it's old and i hadn't done it in a long time. now i'm putting all of my old software back onto the computer. everything else had no problem. adobe lightroom 2 will not let me re-install it and keeps giving me an error message, telling me to contact the software manufacturer. the cd is not damaged at all and i have the serial number for the software, etc... what's wrong? why can't i put it back on my computer? i've done this at least twice before and had no problems.

What version of Mac you are installing and what is the exact error message ?

There were errors installing the software Os x disk 2

Hey guys.
I run an older version of os x (10.4.8) on a Macbook as I have an old version of pro tools that I won't run on anything newer. I havn't gotten round to updating pro tools.
Yesterday, I tried to install the update for 10.4.11 since I'm not too bothered about pro tools anymore.
It took around 2 hours, then at the end seemed to stop without any confirmation of it's success.
After this, everything froze and I was forced to manually restart the macbook using the power button.
When restarting, I got a kernel panic error which asked me to repeatedly start the system.
Fed up with this, I decided to revert back to 10.4.8 by booting from the dvd, erasing the macbook harddrive and installing from scratch.
Disk one went fine, but disk 2 hangs up when installing garage band instruments, then I get the message THERE WERE ERRORS INSTALLING THE SOFTWARE. PLEASE TRY AGAIN.
I've tried this three times with no joy.
Any ideas?
Thanks

Hi Ibin5, and a warm welcome to the forums!
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
It took around 2 hours, then at the end seemed to stop without any confirmation of it's success.
Hmmm, that's too long, might see this...
http://www.apple.com/support/macbook/hd/repairextension/
Also, That second Disk thing happens frequently, the best way around it is to do a Custom install, and eliminate enough Printer Drivers, Languages, Fonts, and Applications you don't need... then it may skip #2 altogether.
http://support.apple.com/kb/HT1442

"There were errors installing the software. Please try again"

I have decided to sell my iMac and G4 iBook, in order to buy a Macbook Pro. I have two people interested, but only if both computers are formatted and as they were when they left the factory.
I erased all my files from both computers, leaving just the system files. I placed the instalation disk for OS X into my iMac (The disk that came with it) and selected instal. I chose the option to delete the current settings and instal a fresh version of OS X.
I hope that makes sense so far.
Anyway after a while, disk 1 had finished, and I was told to insert disk 2. I inserted disk 2, only for half way through the instal process, to be greeted by "There were errors installing the software. Please try again". I have now tried 14 times. I have officially given up.
I have searched these forums for an answer, but it seems as though other people have done things such as, installing other software, or hardware, and that is the cause of the problem. However I have done none of the above. I have tried searching the Mac Support pages, with no luck.
Can anyone help?

I suggest you do the following:
Extended Hard Drive Preparation
1. Boot from your OS X Installer Disk. After the installer loads select your language and click on the Continue button. Then select Disk Utility from the Installer menu (Utilities menu for Tiger.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. Otherwise, click on the Partition tab in the DU main window.
3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
Now try installing OS X. If you still have a problem then it's possible the hard drive is bad or the installer discs are damaged (or possibly just dirty and need a gentle cleaning) or there's a problem with the optical drive.

"there was an error installing the software"???

Hi. Recently I upgraded to a newer version of iTunes on my old iBook G4. The new iTunes wouldn't open without a new (7.5.5 or later) version of Quicktime. I downloaded the new Quicktime, but I can't install it. The installation runs normally until the very end, when the installer suddenly says "There was an error installing the program. Please try installing again." No details are given.
My iBook is old, but it meets the system requirements for Quicktime 7.6.4. I have deleted the old version of Quicktime. I also tried installing Quicktime 7.5.5, but the same error message occurred. I'm at my wit's end. Does anyone have any suggestions? Thanks!

I also have received this error message when trying to update Quicktime/itunes. Any help would be greatly appreciated.

Internal error in the spool system., error key: RFC_ERROR_SYSTEM_FAILURE

Hi All,
I am getting Error when i am viewing my salary slip in ESS.
The Error i am getting is :
Internal error in the spool system., error key: RFC_ERROR_SYSTEM_FAILURE
So can anybody help me out in this.
Regards,
Dhruv Shah

Solved the Error by deleting the spool in the Backend.
Spool was overflow.
Regards,
Dhruv Shah

How can i re-install the operating system without deleting my files on the computer

I'm Trying to re-install the operating system on my macbook, and i dont know, if i can only re-install the OS without deleting the Data on the computer.

If the Snow Leopard version on your Snow Leopard DVD is lower than the Snow Leopard version on your computer, you will NOT in any case be able to re-install the OS the way you want it. You will only be able to erase your disk and then reinstall the OS.
It will only "upgrade" and keep your files if the Mac OS X version of your Snow Leopard DVD is newer than the Snow Leopard version on your computer.

I had to delete everything on my computer and install the operating system again , but I had to install Snow Leopard because it was the cd that came with the computer when I bought it. The problem is that I had already paid for the OS Lion and even h

I had to delete everything on my computer and install the operating system again , but I had to install Snow Leopard because it was the cd that came with the computer when I bought it. The problem is that I had already paid for the OS Lion and even had upgraded to the Mavericks . I do not think it's fair to have to pay again and I would like to upgrade my operating system without having to pay again for the same system.

Hi anatuta,
Thanks for visiting Apple Support Communities.
It sounds like you are trying to upgrade your Mac to a newer version of OS X, after completing a fresh install of Snow Leopard.
If you have already purchased and downloaded OS X Lion and Mavericks, you should be able to find these items in the Purchased section of the Mac App Store.
You may find the steps in this article helpful with finding the items:
Mac App Store: Finding your purchased apps - Apple Support
If you do not see the items in the Purchased section, they may be hidden:
Hide and unhide purchases in the Mac App Store - Apple Support
All the best,
Jeremy

Trying to install the classic system folder

Hi All, I have 10.4.11 installed on my G4 Cube and would like to use OS9 applications. I understand that I have to use the Classic environment and I have followed the apple instructions to restart the MAC with the OS9 disk and install. However, once I get to the OS9.2.1 desktop. the installer says that I cannot write over my existing OS. I cannot seem to see an option to installed the classic system folder..... The only disks I have access to are Retails OSX 10.4 and retail OS9.2.1.. Any ideas? Thanks Garry
Message was edited by: Garry Westwell

Yes, when booted into 10.4, double click on Macintosh HD on the Desktop, what folders do you see there?
Also, open Disk Utility, click on the whole drive on the left, click on the blue Info button, does it report OS9 Drivers installed like mine...
Name : Other World Computing
Type : Disk
Disk Identifier : disk2
Media Name : WDC WD50 00AAKB-00YSA0 Media
Media Type : Generic
Connection Bus : FireWire
Connection Type : External
Connection ID : 512381015163508
Partition Type : Applepartitionscheme
Device Tree : fw/node@1d20200660274/sbp-2@c000/@0:0
Writable : Yes
Ejectable : Yes
Mac OS 9 Drivers Installed : Yes
Location : External
Total Capacity : 465.8 GB (500,107,862,016 Bytes)
S.M.A.R.T. Status : Not Supported
Disk Number : 2
Partition Number : 0

Installing x11 without installing the whole system?

I did not install x11 when I installed Tiger on my Mac G5. I have now, via a number of updates, moved to version 10.4.10.
Sadly, when I insert my system install disk it will not let me install x11 without installing the whole system. That is a risky and impractical situation at this point.
Is there a way to install x11 without installing a whole new system?

On the Installer Disc One there is an installer named 'Optional Installs.' You can install the X11 software from that package without reinstalling OS X.

Processing error in the soyrce system

Hi Experts,
I am extracting payroll data from ECC 5.0 to BW side, after the extraction I'm getting warning message --proceesing error in the source system.
In the source system apllication log the following warning message displyed.
No assignment of payroll data to BW month for country grouping 99.
Diagnosis
No assignment is specified for country grouping 99 in the Customizing activity "Assigning the Payroll Data to BW Month".
System response
The SAP standard "End Date of For-Period" is used for this country grouping.
Procedure
Enter an assignment for the country grouping in Customizing the DataSource 0HR_PY_1.
Choose: R/3 Customizing Implementation Guide -> Integration with Other SAP Components -> Business Information Warehouse -> Settings for Application-Specific DataSources -> Human Resources -> Assigning Payroll Data to a BW Month.
I checked at BW side the data was available in the PSA and Data Target, but the status was in YELLOW for longtime and in the manage tab it is in RED state.
If any one come accross this , please provide good inputs....
Thanks & Regards
SK

Hi,
You have to set the Settings in ECC system
R/3 Customizing Implementation Guide(SPRO) -> Integration with Other SAP Components -> Business Information Warehouse -> Settings for Application-Specific DataSources -> Human Resources -> (Pay-Roll Plugin) Assigning Payroll Data to a BW Month.
make a new entry for the BW Month for the country
Regards
Happy Tony

[SOLVED] Mirrorlist's error installing the base system

Similar Messages

Maybe you are looking for