[solved] NetworkManager does not see the wifi channel 13

Hello!
I have a problem that NetworkManager did not see the wifi network, which broadcasts on channel 13. How to install the drivers for the network to be visible?
Last edited by ghsaehas (2015-01-18 16:57:39)

Install and configure crda:
https://www.archlinux.org/packages/core/x86_64/crda/
http://wireless.kernel.org/en/developer … atory/CRDA

Similar Messages

HT3986 I installed windows 7 successfull, but when I start the mac in windows I does not see the wifi, and others things. How do I get the drivers?

I installed windows 7 successfull, but when I start the mac in windows I does not see the wifi, and others things. How do I get the drivers?
I remember that with Snow Leopard you could download them from the Apple website.
Cheers!

Read the Boot Camp Documentation while you run Boot Camp Assistant to download the Windows Support Software which was the first step in the Boot Camp Setup procedure.

[SOLVED] NetworkManager does not connect to WiFi networks

I'm using `networkmanager` to connect WiFi.
I have selected WiFi Name through `networkmanager`.
Next, enter WiFi Password.
But the problem is, `networkmanager` asks me about password again and again and over again and does not connect to WiFi never !!!!
I'm sure WiFi password that I entered is correct.
Last edited by kamrava (2014-02-22 05:46:37)

orschiro wrote:Maybe not satisfying, but can you instead use Wicd?
My problem was solved. `wicd` was not installed on my system.
My Problem solved through :
I have Installed `wicd` and then NetworkManager works like a charm now
$ sudo pacman -S wicd wicd-gtk
Thank you all.
Last edited by kamrava (2014-02-21 11:29:17)

TS1398 my ipone 4s does not see any wifi networks my ipad works ok tried all of the above resetting network etc still does not see wifi ?

my ipone 4s does not see any wifi networks my ipad works ok tried all of the above resetting network etc still does not see wifi ?

If no change after restoring the iPhone with iTunes as a new iPhone or not from the backup, the iPhone has a hardware problem with the wireless card or with something else.

I have a new time capsule (replace my old time capsule). I want to erase my old one. My computer does not see the old one anymore, how do I connect it (the old TC is not connected to modem)

I have a new time capsule (replace my old time capsule). I want to erase my old one. My computer does not see the old one anymore, how do I connect it (the old TC is not connected to modem). I want to erase it and then use it as either a second hard drive (sired/sirelesly?) or as a hard drive/bridge. So,
1. why doesn't my cmputer see the old TC
2 once i have solved that, how do I erase the old one
3. Can I use the old one as a supplemental hard drive
     a. wired?
     b. wirelessly?
4. Can I use the old one as a range extender?
I know .. a lot of questions but I would appreciate any help.
Thanks

sgetraer wrote:
I have a new time capsule (replace my old time capsule). I want to erase my old one. My computer does not see the old one anymore, how do I connect it (the old TC is not connected to modem). I want to erase it and then use it as either a second hard drive (sired/sirelesly?) or as a hard drive/bridge. So,
1. why doesn't my cmputer see the old TC
2 once i have solved that, how do I erase the old one
3. Can I use the old one as a supplemental hard drive
     a. wired?
     b. wirelessly?
4. Can I use the old one as a range extender?
I know .. a lot of questions but I would appreciate any help.
Thanks
1. Because it is either the same IP as the new one or hidden by being plugged in as a second router.
To access it, isolate one computer from the existing network and plug it directly by ethernet to a lan port of the TC. Use the erase function in the TC to remove all the content of the hard disk.
Then go to the internet tab, connection sharing and select off bridged. You can then reconnect the TC to the network.. and the computer as well. The TC will act as bridged device.. getting IP from the main router and should then appear correctly in Airport utility.
2. I covered in 1. But you just go in airport utility manual setup. disk, and you will see the erase function. You can also set it to bridge and leave the erase until you put it back in the network.. but be careful you erase the right one.
3. You can use the old TC via wired or wireless.. although I would always stick to wired connection if possible. Speed on wireless is 10x worse than wired.
Also note the reliability goes down dramatically after 2 years.. a series 1 3 years old or more is ebay fodder unless you want to repair it. Do not trust vital data to it.. when it dies you will have issues recovering it.
4. Yes, all apple routers will function as wireless extenders. when you do that the ethernet ports turn off so it becomes a purely wireless device.. strange apple decision on what you want to use your TC for.

I bought Ebey NEW Boxed (NEVER OPENED) 16GB Black Iphone 5 Virgin Mobile (USA) NO CONTRACT, want to use it in Europe, particularly in Ukraine, but for some reason now my phone does not see the Ukrainian GSM sim card.

I bought Ebey NEW Boxed (NEVER OPENED) 16GB Black Iphone 5 Virgin Mobile (USA) NO CONTRACT, want to use it in Europe, particularly in Ukraine, but for some reason now my phone does not see the Ukrainian GSM sim card. Please help to solve this problem.

Return it and get your money back. Virgin does not offer official unlocking, thus there's no way to get the phone officially unlocked for you to use it.
Sorry, but you wasted your money.

Audition CC does not see the CD in the drive when I try to burn

Audition CC does not see the CD in the drive when I try to burn CD - says no media found
Windows 8 sees it OK

What folders are you talking about? Photos folders? Email folders?

I am having problems opening images renerated in lightroom5 into cs6. Cs6 bridge does not see the lightroom libarary. If I open lightroom and right clik the image, edit in cs6, 6 opens but the picture doesnot follow. What is going on? Give me a hand.

I am having problems opening images renerated in lightroom5 into cs6. Cs6 bridge does not see the lightroom libarary. If I open lightroom and right clik the image, edit in cs6, 6 opens but the picture doesnot follow. What is going on? Give me a hand, thanks.

What edition of LR 5? What edition of ACR does PSCS 6 contain. If they are not parallel (same edition number x in [5 or 8].x ), is LR making a tiff or psd rendition of the image?

Wiped our old iPad 1 clean, now can't install iOS from iTunes. iTunes does not "see" the devise. Tried uninstalling and installing iTunes on laptop. Also bought new USB cable. The iPad is charging, but that's all it does.

Wiped our old iPad 1 clean, now can't install iOS from iTunes using laptop PC (W Vista). iTunes does not "see" the device. Tried uninstalling and installing iTunes on laptop. Also bought new USB cable. The iPad is charging, but that's all it does. Just want to get it operating again for browsing and e-reading.

OK. You merely erased the content and settings. The IOS is still there.
If it has NEVER been jailbroke, here are some standard repair procedures. From what you've already stated, my guess is that you'll end up with Recovery Mode described in the last paragraph.
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, read this.

My iMac does not see the new Toshiba external drive in Finder or Disk Utility. How can I get it to see the drive?

My iMac does not see the new Toshiba external drive in Finder or Disk Utility. How can I get it to see the drive?

From the menu bar, select
 ▹ System Preferences ▹ Energy Saver ▹ Power Adapter
and uncheck the box labeled Put the hard disk(s) to sleep when possible, if it's checked.
If the drive has more than one interface (USB, FireWire, Thunderbolt, eSATA), try one of the other interfaces.
Check that the data cable is securely inserted at both ends.
Try a different cable.
If you're connecting the drive through a hub, connect it directly to a built-in port on the Mac.
If you're connecting it directly, try a different port.
Disconnect all other devices on the bus, or as many as possible.
Test the drive with another Mac. Test another drive with this Mac.
If the drive is bus-powered, but has an AC adapter, connect the adapter.
Start up in Recovery mode and launch Disk Utility. Is the drive recognized?
Start up in Safe Mode and test.
Reset the NVRAM.
Reset the System Management Controller.
If the drive doesn't work under any of the above conditions, and if another drive does work with the same Mac, then the drive is malfunctioning.

I am trying to update my iphone 3GS software but itunes just says that this is the current version of itunes, it does not see the phone update - anyone know how to get the phone updated?

I am trying to update my iphone 3GS software but itunes just says that this is the current version of itunes, it does not see the phone update - anyone know how to get the phone updated?

Mike
I have done that and it is through pressing that update, which tells me that there is anew version of iphone software, that the prompt comes telling me that this is the current itunes?

I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

Suggest that you perform a Factory Default Reset as follows:
Pull the Express from power
Wait a few moments
Hold in the reset button and keep holding it an additonal 8-10 seconds while you plug the Express back in to power
Release the reset button and allow 40-45 seconds for the Express to restart
Apple's instructions to do what you want are here:
It will often help to temporarily connect an Ethernet cable from your Mac to the AirPort Express for the setup. Once the Express is configured, you can disconnect the Ethernet cable and move the Express to the desired location.
http://support.apple.com/kb/HT4259
Although an AirPort Extreme is shown as the extending device in the example, the setup for an AirPort Express is exactly the same

TS1538 after a restore, the itouch screen has a "USB arrow to iTunes" picture. Now iTunes does not see the itouch and my itouch is non-responsive

i was restoring my itouch and after completed, the itouch screen has a "USB arrow to iTunes" picture. Now iTunes does not see the itouch and my itouch is non-responsive

Try DFU mode and then restore
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

I am trying to import i frame from an SD90 video camera to iMovie, but it does not see the camera. Footage goes to i photo Why?

I am trying to import video ( i frame) from an sd90 ( listed for mac) but i movie does not see the camera. It imports into i photo. Is this normal ?

If you quit iPhoto and iMovie (with the camera still attached) then put the camera into VCR playback mode. Then launch iMovie and see if it can see the camera. If not, get out the power adapter for the camera and plug it into the wall, plug the camera into the power adapter. Reboot your Mac and wait for iPhoto to launch again automatically. Don't let it import the clips, just say No, quit the program. Then put the camrea int VCR/Playback mode, launch iMovie and check again to see if it can see the camera. Once iMovie sees it the first time it should be quicker to recognize it in future. But iPhoto does try to race in there and grab everything first.
To turn this off go to iPhoto Menu in iPhoto > Preferences > Look for Connecting camera opens: (click on the pulldown menu and choose No Application) This effectively turns off iPhoto when you first attach the camera. And it opens the way to iMovie recognizing it quicker.

I have a MacBook Pro running 10.7.2. I am trying to import photos from my older Canon EOS-1D for the first time since my OS upgrade. iPhoto does not see the camera nor does Image Capture. IC says there is not a camera connected. Cable is known good.

I have a MacBook Pro running 10.7.2. I am trying to import photos from my older Canon EOS-1D for the first time since my OS upgrade. iPhoto does not see the camera nor does Image Capture. IC says there is not a camera connected. Cable is known good. Has something changed? Thanks!

If neither iPhoto not IC can seethe card it might suggest an issue with the card or the ports on the camera/mac.
Try reformat the card, change the ports and/or use a USB Card Reader.

[solved] NetworkManager does not see the wifi channel 13

Similar Messages

Maybe you are looking for