[solved] No speaker sound after suspend

Hey I'm wondering if someone can help me out with this. My speakers work fine after cold boot / reboot, but after suspend there is no sound. Headphones still work before / after suspend. This started quite a while ago, and I've been following this other thread: https://bbs.archlinux.org/viewtopic.php?id=163248 but nothing has worked so far.
It's on a Dell M1330 laptop. Below are some hopefully helpful outputs - I didn't notice anything different between before and after suspend outputs.
Any help is appreciated. Thanks
dg@dg-laptop> cat /proc/asound/card0/codec\#0 | grep Codec
Codec: SigmaTel STAC9228
lspci -vvnn (relevant bits)
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
Subsystem: Dell Device [1028:0209]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at f6ffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
dg@dg-laptop> amixer ~
Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback 0 - 127
Mono: Playback 107 [84%] [-15.00dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pvolume pswitch
Playback channels: Front Left - Front Right
Limits: Playback 0 - 127
Mono:
Front Left: Playback 127 [100%] [0.00dB] [on]
Front Right: Playback 127 [100%] [0.00dB] [on]
Simple mixer control 'Headphone',1
Capabilities: pvolume pswitch
Playback channels: Front Left - Front Right
Limits: Playback 0 - 127
Mono:
Front Left: Playback 127 [100%] [0.00dB] [on]
Front Right: Playback 127 [100%] [0.00dB] [on]
Simple mixer control 'Speaker',0
Capabilities: pvolume pswitch
Playback channels: Front Left - Front Right
Limits: Playback 0 - 127
Mono:
Front Left: Playback 127 [100%] [0.00dB] [on]
Front Right: Playback 127 [100%] [0.00dB] [on]
Simple mixer control 'PCM',0
Capabilities: pvolume
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 255 [100%] [0.00dB]
Front Right: Playback 255 [100%] [0.00dB]
Simple mixer control 'Mic Boost',0
Capabilities: volume
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: 0 - 4
Front Left: 0 [0%] [0.00dB]
Front Right: 0 [0%] [0.00dB]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Playback Source',0
Capabilities: enum
Items: 'Digital Playback' 'ADAT' 'Analog Mux 1' 'Analog Mux 2' 'Analog Mux 3'
Item0: 'Digital Playback'
Simple mixer control 'Beep',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback 0 - 3
Mono: Playback 0 [0%] [-18.00dB] [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch
Capture channels: Front Left - Front Right
Limits: Capture 0 - 14
Front Left: Capture 0 [0%] [0.00dB] [on]
Front Right: Capture 0 [0%] [0.00dB] [on]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch
Capture channels: Front Left - Front Right
Limits: Capture 0 - 14
Front Left: Capture 0 [0%] [0.00dB] [off]
Front Right: Capture 0 [0%] [0.00dB] [off]
Simple mixer control 'Capture',2
Capabilities: cvolume cswitch
Capture channels: Front Left - Front Right
Limits: Capture 0 - 14
Front Left: Capture 0 [0%] [0.00dB] [off]
Front Right: Capture 0 [0%] [0.00dB] [off]
Simple mixer control 'Auto-Mute Mode',0
Capabilities: enum
Items: 'Disabled' 'Enabled'
Item0: 'Enabled'
Simple mixer control 'Digital',0
Capabilities: cvolume
Capture channels: Front Left - Front Right
Limits: Capture 0 - 120
Front Left: Capture 60 [50%] [0.00dB]
Front Right: Capture 60 [50%] [0.00dB]
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Internal Mic 1'
Item0: 'Internal Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Internal Mic 1'
Item0: 'Internal Mic'
Simple mixer control 'Input Source',2
Capabilities: cenum
Items: 'Mic' 'Internal Mic' 'Internal Mic 1'
Item0: 'Internal Mic'
Last edited by dandaman0061 (2013-07-16 14:06:07)

buri wrote:
Same problem, kenel 3.9.x and 3.10.x on my old Dell Vostro 1500. Try this:
edit /etc/modprobe.d/alsa-base.conf
options snd-hda-intel enable_msi=0 model=eapd
I found solution on the internet and I do not know why it works.
This didn't seem to work for me...
skunktrader wrote:I had the same problem, but setting "Auto-Mute Mode" to disabled solved it for me
This did work! It'd be nice to have the auto-mute functionality, but I don't use headphones *that* often.
Thanks to both!

Similar Messages

HT4623 My iPad 3 has lost the speaker sound after updating to iOS 6.1, headphones are working fine

My iPad 3 has lost the speaker sound after updating to iOS 6.1, headphones are working fine. Please help me out, done all the troubleshooting like restarting, side switcing, cleeaning the headphone jack etc.,

Hi I also have this problem. Sound was only working on the headphones and also on the volume slider in the settings app. Everywhere else I get no sound and no volume slider. Now the headphones don't work either.
(I'm using an ipad 2 iOS 6.1.2)
And NO it's not muted. I've reset all settings and restarted the iPad. Been searching forums for a couple days. Some say its a dirty docking port problem, others suggest a Skype or other app update that could be the problem.
No volume control icon appears when I press the volume control buttons. Only says sound effects, if it says anything at all. Most often there is NO volume icon. YouTube, video, music, and other game apps, no sound.

[Solved]no sound after suspend/resume after kernel 3.9.2 upgrade

I don't know what to provide to help solve this problem. Leave me messages.Thank you!
Last edited by chu887 (2013-06-06 08:54:16)

johni wrote:
I got mine working!
First I commented out the module parameter from my /etc/modprobe.d//intel-hda-audio.conf:
#options snd-hda-intel model=dell-eq
Since it works without that now, I will probably remove the file.
Next, I went into alsamixer, and noticed a couple items not there before, turned down low:
"Speaker", and two "HeadPhone" mixers, both turned down almost off. I turned up the volume on the speaker, and was able to get sound from the speakers. The same worked for the headphone entries (I have two headphone jacks).
After I did this, it works better than before because I used to only have one working headphone jack.
Also, I confirmed sound is still working after suspend/resume for me.
Hopefully this will help one of you.
Thanks,the problem has been resolved by downgrade.
Sound is absolutely normal before I suspend/resume my system, volume is normal, not too large,not too little. But there's no sound at all after resume it . I guess it's probably to have something to do with our audio card - HDA intel, my computer is also a dell laptop( dell 1420 , 2007/2008, really old ).
My advice is : don't upgrade to kernel 3.9.2 ,it's an odd version( odd version is not stable).

[SOLVED] Losing network connection after suspend

Lately I'm having this peculiar problem. When resuming after suspend (specifically, pm-suspend), I have no network connection. I first noticed this on March 31st. The only thing that changed was that I upgraded these packages:
openssl-1.0.1-2-x86_64.pkg.tar.xz
xf86-video-ati-6.14.4-2-x86_64.pkg.tar.xz
lib32-libdrm-2.4.33-1-x86_64.pkg.tar.xz
libnotify-0.7.5-1-x86_64.pkg.tar.xz
xz-5.0.3-2-x86_64.pkg.tar.xz
vim-taglist-45-5-any.pkg.tar.xz
But I'm pretty sure I would have suspended and resumed successfully at least once after that upgrade.
Can anyone suggest what I should look at to try to diagnose this?
Thanks
Last edited by ibrunton (2012-04-06 11:26:03)

Same issue here. Looks like dhcpcd crashes during or after running /usr/lib/dhcpcd/dhcpcd-run-hooks on resume from suspend. I'll try downgrading until this is fixed.
$ uname -s -v -r -m
Linux 3.2.13-1-ARCH #1 SMP PREEMPT Sat Mar 24 09:10:39 CET 2012 x86_64
$ pacman -Qi dhcpcd
Name : dhcpcd
Version : 5.5.5-1
URL : http://roy.marples.name/dhcpcd/
Licenses : BSD
Groups : base
Provides : None
Depends On : glibc sh
Optional Deps : None
Required By : networkmanager
Conflicts With : None
Replaces : None
Installed Size : 256.00 KiB
Packager : Ronald van Haren <[email protected]>
Architecture : x86_64
Build Date : Fri Mar 23 17:25:47 2012
Install Date : Thu Mar 29 23:36:13 2012
Install Reason : Explicitly installed
Install Script : No
Description : RFC2131 compliant DHCP client daemon
# dhcpcd -d -B eth0
dhcpcd[1865]: version 5.5.5 starting
dhcpcd[1865]: eth0: using hwaddr bc:ae:c5:75:36:8e
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason PREINIT
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason CARRIER
dhcpcd[1865]: eth0: sending IPv6 Router Solicitation
dhcpcd[1865]: eth0: reading lease `/var/lib/dhcpcd/dhcpcd-eth0.lease'
dhcpcd[1865]: eth0: rebinding lease of 192.168.1.100
dhcpcd[1865]: eth0: sending REQUEST (xid 0x36169f23), next in 3.93 seconds
dhcpcd[1865]: eth0: acknowledged 192.168.1.100 from 192.168.1.1
dhcpcd[1865]: eth0: checking for 192.168.1.100
dhcpcd[1865]: eth0: sending ARP probe (1 of 3), next in 2.00 seconds
dhcpcd[1865]: eth0: sending ARP probe (2 of 3), next in 1.81 seconds
dhcpcd[1865]: eth0: sending IPv6 Router Solicitation
dhcpcd[1865]: eth0: sending ARP probe (3 of 3), next in 2.00 seconds
dhcpcd[1865]: eth0: leased 192.168.1.100 for 3600 seconds
dhcpcd[1865]: eth0: adding IP address 192.168.1.100/24
dhcpcd[1865]: eth0: adding route to 192.168.1.0/24
dhcpcd[1865]: eth0: adding default route via 192.168.1.1
dhcpcd[1865]: eth0: writing lease `/var/lib/dhcpcd/dhcpcd-eth0.lease'
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason BOUND
dhcpcd[1865]: eth0: sending ARP announce (1 of 2), next in 2.00 seconds
dhcpcd[1865]: eth0: sending IPv6 Router Solicitation
dhcpcd[1865]: eth0: sending ARP announce (2 of 2)
dhcpcd[1865]: eth0: sending IPv6 Router Solicitation
dhcpcd[1865]: eth0: no IPv6 Routers available
dhcpcd[1865]: eth0: carrier lost
dhcpcd[1865]: eth0: deleting default route via 192.168.1.1
dhcpcd[1865]: eth0: deleting route to 192.168.1.0/24
dhcpcd[1865]: eth0: deleting IP address 192.168.1.100/24
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason NOCARRIER
dhcpcd[1865]: eth0: carrier acquired
dhcpcd[1865]: eth0: using hwaddr bc:ae:c5:75:36:8e
dhcpcd[1865]: eth0: executing `/usr/lib/dhcpcd/dhcpcd-run-hooks', reason CARRIER
*** glibc detected *** dhcpcd: double free or corruption (fasttop): 0x0000000000ac2860 ***
======= Backtrace: =========
/lib/libc.so.6(+0x78a56)[0x7f9b6a794a56]
dhcpcd[0x40cdd0]
dhcpcd[0x40e597]
dhcpcd[0x4093f0]
dhcpcd[0x411ba7]
dhcpcd[0x411563]
dhcpcd[0x40768f]
dhcpcd[0x40aa6b]
dhcpcd[0x4028a8]
/lib/libc.so.6(__libc_start_main+0xf5)[0x7f9b6a73d455]
dhcpcd[0x402d1d]
======= Memory map: ========
00400000-00419000 r-xp 00000000 fe:02 4590719 /sbin/dhcpcd
00619000-0061a000 r--p 00019000 fe:02 4590719 /sbin/dhcpcd
0061a000-0061b000 rw-p 0001a000 fe:02 4590719 /sbin/dhcpcd
0061b000-0061c000 rw-p 00000000 00:00 0
00ac1000-00ae3000 rw-p 00000000 00:00 0 [heap]
7f9b6a2eb000-7f9b6a300000 r-xp 00000000 fe:02 1063993 /usr/lib/libgcc_s.so.1
7f9b6a300000-7f9b6a4ff000 ---p 00015000 fe:02 1063993 /usr/lib/libgcc_s.so.1
7f9b6a4ff000-7f9b6a500000 rw-p 00014000 fe:02 1063993 /usr/lib/libgcc_s.so.1
7f9b6a500000-7f9b6a517000 r-xp 00000000 fe:02 3014810 /lib/libpthread-2.15.so
7f9b6a517000-7f9b6a716000 ---p 00017000 fe:02 3014810 /lib/libpthread-2.15.so
7f9b6a716000-7f9b6a717000 r--p 00016000 fe:02 3014810 /lib/libpthread-2.15.so
7f9b6a717000-7f9b6a718000 rw-p 00017000 fe:02 3014810 /lib/libpthread-2.15.so
7f9b6a718000-7f9b6a71c000 rw-p 00000000 00:00 0
7f9b6a71c000-7f9b6a8b3000 r-xp 00000000 fe:02 3018245 /lib/libc-2.15.so
7f9b6a8b3000-7f9b6aab3000 ---p 00197000 fe:02 3018245 /lib/libc-2.15.so
7f9b6aab3000-7f9b6aab7000 r--p 00197000 fe:02 3018245 /lib/libc-2.15.so
7f9b6aab7000-7f9b6aab9000 rw-p 0019b000 fe:02 3018245 /lib/libc-2.15.so
7f9b6aab9000-7f9b6aabd000 rw-p 00000000 00:00 0
7f9b6aabd000-7f9b6aac4000 r-xp 00000000 fe:02 3014856 /lib/librt-2.15.so
7f9b6aac4000-7f9b6acc3000 ---p 00007000 fe:02 3014856 /lib/librt-2.15.so
7f9b6acc3000-7f9b6acc4000 r--p 00006000 fe:02 3014856 /lib/librt-2.15.so
7f9b6acc4000-7f9b6acc5000 rw-p 00007000 fe:02 3014856 /lib/librt-2.15.so
7f9b6acc5000-7f9b6ace6000 r-xp 00000000 fe:02 3018769 /lib/ld-2.15.so
7f9b6aea5000-7f9b6aea9000 rw-p 00000000 00:00 0
7f9b6aee4000-7f9b6aee6000 rw-p 00000000 00:00 0
7f9b6aee6000-7f9b6aee7000 r--p 00021000 fe:02 3018769 /lib/ld-2.15.so
7f9b6aee7000-7f9b6aee8000 rw-p 00022000 fe:02 3018769 /lib/ld-2.15.so
7f9b6aee8000-7f9b6aee9000 rw-p 00000000 00:00 0
7ffff8b93000-7ffff8bb4000 rw-p 00000000 00:00 0 [stack]
7ffff8bc9000-7ffff8bca000 r-xp 00000000 00:00 0 [vdso]
ffffffffff600000-ffffffffff601000 r-xp 00000000 00:00 0 [vsyscall]

[Solved] "cannot open display" after suspend/resume, possibly broadcom

Hey peoples,
[EDIT: I think my initial assumptions are incorrect, this issue seems to be occurring independently of whatever wifi driver I have loaded]
I'm finding that after suspend/resume my machine will not open any new windows. The windows that were already open continue to function. If I've left a terminal open, and attempt to open a new window I get the message:
[framps@localhost ~]$ firefox
Invalid MIT-MAGIC-COOKIE-1 keyInvalid MIT-MAGIC-COOKIE-1 keyError: cannot open display: :0.0
I've found that removing the broadcom-wl driver from my system seems to fix the issue. I can't see anything particularly obvious in my dmesg. I think I need the broadcom-wl driver as I have not been able to get b43 or bcma to work for my machine.
[ 948.814261] cfg80211: World regulatory domain updated:
[ 948.814266] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 948.814269] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 948.814272] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 948.814275] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 948.814277] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 948.814280] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 949.404722] r8169 0000:0c:00.0 eth0: link down
[ 949.404741] r8169 0000:0c:00.0 eth0: link down
[ 949.404773] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 949.355635] PM: Syncing filesystems ... done.
[ 949.717960] PM: Preparing system for mem sleep
[ 949.851316] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 949.862059] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 949.875377] PM: Entering mem sleep
[ 949.875472] Suspending console(s) (use no_console_suspend to debug)
[ 950.064255] xhci_hcd 0000:00:14.0: WARN Event TRB for slot 1 ep 0 with no TDs queued?
[ 950.064507] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 950.075138] sd 0:0:0:0: [sda] Stopping disk
[ 950.165918] ERROR @wl_notify_scan_status : Scan complete while device not scanning
[ 950.477845] i915 0000:00:02.0: power state changed by ACPI to D3hot
[ 950.551140] PM: suspend of devices complete after 676.056 msecs
[ 950.551485] PM: late suspend of devices complete after 0.342 msecs
[ 950.567669] r8169 0000:0c:00.0: wake-up capability enabled by ACPI
[ 950.581418] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[ 950.594384] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[ 950.620974] xhci_hcd 0000:00:14.0: wake-up capability enabled by ACPI
[ 950.634321] PM: noirq suspend of devices complete after 82.939 msecs
[ 950.634762] ACPI: Preparing to enter system sleep state S3
[ 950.730816] PM: Saving platform NVS memory
[ 950.736910] Disabling non-boot CPUs ...
[ 950.738461] smpboot: CPU 1 is now offline
[ 950.840631] smpboot: CPU 2 is now offline
[ 950.943831] smpboot: CPU 3 is now offline
[ 950.944231] Extended CMOS year: 2000
[ 950.945389] ACPI: Low-level resume complete
[ 950.945427] PM: Restoring platform NVS memory
[ 950.945811] Extended CMOS year: 2000
[ 950.945864] Enabling non-boot CPUs ...
[ 950.949268] smpboot: Booting Node 0 Processor 1 APIC 0x1
[ 950.963117] CPU1 is up
[ 950.966520] smpboot: Booting Node 0 Processor 2 APIC 0x2
[ 950.980330] CPU2 is up
[ 950.980386] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 950.994238] CPU3 is up
[ 950.997398] ACPI: Waking up from system sleep state S3
[ 951.471580] i915 0000:00:02.0: power state changed by ACPI to D0
[ 951.498111] xhci_hcd 0000:00:14.0: wake-up capability disabled by ACPI
[ 951.524753] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[ 951.551380] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[ 951.564744] nvidia 0000:01:00.0: power state changed by ACPI to D0
[ 951.591567] PM: noirq resume of devices complete after 120.295 msecs
[ 951.591837] PM: early resume of devices complete after 0.236 msecs
[ 951.591891] i915 0000:00:02.0: setting latency timer to 64
[ 951.591894] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 951.591968] mei 0000:00:16.0: irq 43 for MSI/MSI-X
[ 951.591983] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 951.592037] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 951.592108] ahci 0000:00:1f.2: setting latency timer to 64
[ 951.592119] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[ 951.594182] r8169 0000:0c:00.0: wake-up capability disabled by ACPI
[ 951.634511] [drm:__gen6_gt_force_wake_mt_get] *ERROR* Timed out waiting for forcewake old ack to clear.
[ 951.636110] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 951.796066] r8169 0000:0c:00.0 eth0: link down
[ 951.824070] Extended CMOS year: 2000
[ 951.831119] usb 3-1.3: reset full-speed USB device number 3 using ehci_hcd
[ 951.910921] ata5: SATA link down (SStatus 0 SControl 300)
[ 951.916168] btusb 3-1.3:1.0: no reset_resume for driver btusb?
[ 951.916171] btusb 3-1.3:1.1: no reset_resume for driver btusb?
[ 951.924226] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 951.926030] ata2.00: configured for UDMA/100
[ 951.981369] usb 4-1.6: reset high-speed USB device number 3 using ehci_hcd
[ 952.876326] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 952.877743] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 952.877747] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 952.877750] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 952.880489] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 952.880493] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 952.880496] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 952.881600] ata1.00: configured for UDMA/100
[ 952.893105] sd 0:0:0:0: [sda] Starting disk
[ 952.911681] PM: resume of devices complete after 1321.544 msecs
[ 952.912745] PM: Finishing wakeup.
[ 952.912748] Restarting tasks ... done.
[ 953.018321] video LNXVIDEO:00: Restoring backlight state
[ 953.018862] video LNXVIDEO:01: Restoring backlight state
[ 953.376503] r8169 0000:0c:00.0 eth0: link up
[ 953.376515] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Any help would be greatly appreciated. Thanks.
Last edited by frampy (2013-03-16 01:20:57)

It seems that the only option for my wifi card, BCM43228 is the proprietary broadcom-wl.
Can anyone suggest how I might be able to get any debugging information for this module? Maybe this driver is conflicting with something else on my system, as I can't find anyone else that is seeing this same issue.
Very frustrating, my machine is a Thinkpad Edge E530. Because I ordered from New Zealand there was no option to include the alternative Intel card and I was stuck with the broadcom. Apparently there's a whitelist on the BIOS aswell which will prevent me from installing another card.

[SOLVED] USB stop work after suspend (only right ports!!!)

Hi,
It drives me crazy!
I recently installed Arch on my new laptop SAMSUNG NP900X4C that have 3 USB ports, one in the left side and two in the right side . When I boot the system (or reboot) all USB ports works fine, but after system suspend like close lid, only the left port go back work. dmesg shows nothing when I plug a pendrive in the any right USB ports, even less lsblk.
This is my dmesg out when I connect the pendrive in all ports after boot:
[ 181.776489] usb 1-1.2: new high-speed USB device number 5 using ehci_hcd
[ 181.880249] Initializing USB Mass Storage driver...
[ 181.880381] scsi6 : usb-storage 1-1.2:1.0
[ 181.880498] usbcore: registered new interface driver usb-storage
[ 181.880500] USB Mass Storage support registered.
[ 182.883580] scsi 6:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ: 0 ANSI: 5
[ 182.885191] sd 6:0:0:0: [sdb] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 182.886674] sd 6:0:0:0: [sdb] Write Protect is off
[ 182.886688] sd 6:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 182.887530] sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 182.898516] sdb: sdb1
[ 182.901936] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 185.427222] usb 1-1.2: USB disconnect, device number 5
[ 188.486360] usb 2-2: new high-speed USB device number 2 using xhci_hcd
[ 188.503289] usb 2-2: ep 0x81 - rounding interval to 32768 microframes, ep desc says 0 microframes
[ 188.505259] scsi7 : usb-storage 2-2:1.0
[ 189.506730] scsi 7:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ: 0 ANSI: 5
[ 189.508371] sd 7:0:0:0: [sdb] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 189.510955] sd 7:0:0:0: [sdb] Write Protect is off
[ 189.510968] sd 7:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 189.512566] sd 7:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 189.523657] sdb: sdb1
[ 189.527290] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 191.469673] usb 2-2: USB disconnect, device number 2
[ 193.515534] usb 2-1: new high-speed USB device number 3 using xhci_hcd
[ 193.532133] usb 2-1: ep 0x81 - rounding interval to 32768 microframes, ep desc says 0 microframes
[ 193.533952] scsi8 : usb-storage 2-1:1.0
[ 194.535796] scsi 8:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ: 0 ANSI: 5
[ 194.537477] sd 8:0:0:0: [sdb] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 194.540055] sd 8:0:0:0: [sdb] Write Protect is off
[ 194.540069] sd 8:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 194.541588] sd 8:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 194.553582] sdb: sdb1
[ 194.557933] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[ 196.298812] usb 2-1: USB disconnect, device number 3
Same after suspend:
[ 568.168987] PM: Syncing filesystems ... done.
[ 568.187450] PM: Preparing system for mem sleep
[ 568.259525] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 568.270762] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 568.284097] PM: Entering mem sleep
[ 568.284201] Suspending console(s) (use no_console_suspend to debug)
[ 568.298234] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 568.300100] sd 0:0:0:0: [sda] Stopping disk
[ 568.949683] PM: suspend of devices complete after 665.917 msecs
[ 568.950083] PM: late suspend of devices complete after 0.395 msecs
[ 568.963325] r8169 0000:02:00.0: wake-up capability enabled by ACPI
[ 569.016282] PM: noirq suspend of devices complete after 66.291 msecs
[ 569.017160] ACPI: Preparing to enter system sleep state S3
[ 569.036433] PM: Saving platform NVS memory
[ 569.042305] Disabling non-boot CPUs ...
[ 569.044189] smpboot: CPU 1 is now offline
[ 569.047218] smpboot: CPU 2 is now offline
[ 569.049866] smpboot: CPU 3 is now offline
[ 569.050441] Extended CMOS year: 2000
[ 569.052505] ACPI: Low-level resume complete
[ 569.052550] PM: Restoring platform NVS memory
[ 569.052918] Extended CMOS year: 2000
[ 569.052981] Enabling non-boot CPUs ...
[ 569.059788] smpboot: Booting Node 0 Processor 1 APIC 0x1
[ 569.074350] CPU1 is up
[ 569.074412] smpboot: Booting Node 0 Processor 2 APIC 0x2
[ 569.088727] CPU2 is up
[ 569.088868] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 569.103096] CPU3 is up
[ 569.108227] ACPI: Waking up from system sleep state S3
[ 569.262105] PM: noirq resume of devices complete after 106.814 msecs
[ 569.262496] PM: early resume of devices complete after 0.234 msecs
[ 569.262565] i915 0000:00:02.0: setting latency timer to 64
[ 569.262604] mei 0000:00:16.0: irq 46 for MSI/MSI-X
[ 569.262694] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 569.262706] ahci 0000:00:1f.2: setting latency timer to 64
[ 569.262744] snd_hda_intel 0000:00:1b.0: irq 50 for MSI/MSI-X
[ 569.262805] r8169 0000:02:00.0: wake-up capability disabled by ACPI
[ 569.310850] xhci_hcd 0000:03:00.0: WARN: xHC restore state timeout
[ 569.310949] xhci_hcd 0000:03:00.0: PCI post-resume error -110!
[ 569.310953] xhci_hcd 0000:03:00.0: HC died; cleaning up
[ 569.310960] xhci_hcd 0000:03:00.0: HC died; cleaning up
[ 569.310985] dpm_run_callback(): pci_pm_resume+0x0/0xd0 returns -110
[ 569.311032] PM: Device 0000:03:00.0 failed to resume async: error -110
[ 569.312717] mei 0000:00:16.0: wd: failed to find the client
[ 569.324628] Extended CMOS year: 2000
[ 569.331940] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 569.387202] r8169 0000:02:00.0: enp2s0: link down
[ 569.534701] usb 1-1.5: reset full-speed USB device number 3 using ehci_hcd
[ 569.621070] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 569.621077] btusb 1-1.5:1.1: no reset_resume for driver btusb?
[ 569.674395] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 569.675511] ata1.00: configured for UDMA/133
[ 569.675675] sd 0:0:0:0: [sda] Starting disk
[ 569.684439] usb 1-1.6: reset high-speed USB device number 4 using ehci_hcd
[ 569.969276] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S
[ 569.976072] iwlwifi 0000:01:00.0: Radio type=0x2-0x1-0x0
[ 570.377316] PM: resume of devices complete after 1116.468 msecs
[ 570.378930] PM: Finishing wakeup.
[ 570.378933] Restarting tasks ... done.
[ 570.409428] video LNXVIDEO:00: Restoring backlight state
[ 606.007121] usb 1-1.2: new high-speed USB device number 6 using ehci_hcd
[ 606.092964] scsi9 : usb-storage 1-1.2:1.0
[ 607.094056] scsi 9:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ: 0 ANSI: 5
[ 607.096239] sd 9:0:0:0: [sdb] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 607.097828] sd 9:0:0:0: [sdb] Write Protect is off
[ 607.097836] sd 9:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 607.098834] sd 9:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 607.110498] sdb: sdb1
[ 607.113670] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[ 613.233780] usb 1-1.2: USB disconnect, device number 6
Nothing appears about the USB ports 2-2 and 2-1. Any ideia?!
I even tried to install laptop-mode-tools and set CONTROL_USB_AUTOSUSPEND=0 but didn't work
Last edited by otto_simpson (2013-01-23 01:28:49)

Oh crap! I am kid with his new toy...
After a lot of google it I read something about firmware control the wake up of USB 3.0 and when I entered in this laptop BIOS what I found?! This option disabled:
USB S3 Wake-up [Disable]
So, just enable it and all my USB ports go back to work after suspend. I don't understand the purpose of it disabled by default.
Anyway I am sorry for this newbie mistake.
Last edited by otto_simpson (2013-01-23 04:16:20)

Only "Headphones" sound, no speaker sound after 4.2.1 upgrading

After I had finished upgrading 4.2.1 firmware for my iPad, the speaker's sound has gone.
I can hear the sound from my iPad only when I connected to any headphones or bluetooth devices.
I tried many methods to get the sound back, starting from:
1. trying to plug in and out my headphone - nothing changed
2. switch on and off from the mute button (former is lock button) but it only showed "Headphones" or "Mute" sign.
3. shut down and turn on my iPad - nothing changed
4. Hard Reset my iPad and Restore - Still no sound, but I had to re-install everything again
5. Ask everyone and search every "no sound from iPad" topics but found none like mine.
However, while I upgraded the firmware, I noticed that I "locked" the screen during the process and I heard someone in the internet told me that it might be the origin of my problem.
I tried to sync my iPad and find how to re-upgrading the firmware again with no "locked" the button but there is no way to.

I've been having this problem for several months and just found this thread. Unfortunately the solution isn't well spelled out, but I was able to resolve the issue.
To recap:
Problem: Many/most non-Apple Apps have no sound from the iPad internal speaker. Plugging headphones in provides sound from all apps. Apple Apps (youtube, music, video, safari, etc) continue to function and play sound out of internal speakers normally.
Resolution: This issue appears to be related to the 'mute' / screen orientation lock button. If your iPad mute switch was on mute when you switched it to orientation lock, 3rd party apps will remain muted via internal speakers no matter what you do. Luckily an easy fix: Go Settings -> General and switch from 'lock rotation' to mute. Slide the switch to the non-muted position. You can now switch back to 'lock rotation' and your apps will play sound from the internal speaker again!!!

[SOLVED] mpd - no sound after Pulseaudio update

After update of Pulseaudio (1.04) I mpd doesn't work - there's no problem with other applications, only with mpd. I can't set volume and mpc says that there are problems with opening audio device:
eregus@arch ~ $ mpc
Black River - Street Games
[paused] #769/775 0:00/3:45 (0%)
volume: n/a repeat: off random: off single: off consume: off
ERROR: problems opening audio device
There's my /etc/mpd.conf:
music_directory "/mnt/sda3/music"
playlist_directory "/var/lib/mpd/playlists"
db_file "/var/lib/mpd/mpd.db"
log_file "syslog"
pid_file "/run/mpd/mpd.pid"
state_file "/var/lib/mpd/mpdstate"
user "mpd"
auto_update "yes"
input {
plugin "curl"
audio_output {
type "pulse"
name "pulse audio"
I use ALSA + Pulseaudio. My /etc/pulse/default.pa:
.nofail
.fail
load-module module-device-restore
load-module module-stream-restore
load-module module-card-restore
load-module module-augment-properties
load-module module-alsa-sink device=dmix
load-module module-alsa-source device=dsnoop
.ifexists module-udev-detect.so
.else
.endif
.ifexists module-jackdbus-detect.so
.nofail
load-module module-jackdbus-detect
.fail
.endif
.ifexists module-bluetooth-policy.so
load-module module-bluetooth-policy
.endif
.ifexists module-bluetooth-discover.so
load-module module-bluetooth-discover
.endif
.ifexists module-esound-protocol-unix.so
load-module module-esound-protocol-unix
.endif
load-module module-native-protocol-unix
load-module module-native-protocol-tcp auth-ip-acl=127.0.0.1
.ifexists module-gconf.so
.nofail
load-module module-gconf
.fail
.endif
load-module module-default-device-restore
load-module module-rescue-streams
load-module module-always-sink
load-module module-intended-roles
load-module module-suspend-on-idle
.ifexists module-console-kit.so
.nofail
load-module module-console-kit
.fail
.endif
.ifexists module-systemd-login.so
load-module module-systemd-login
.endif
load-module module-position-event-sounds
load-module module-role-cork
load-module module-filter-heuristics
load-module module-filter-apply
.ifexists module-dbus-protocol.so
load-module module-dbus-protocol
.endif
load-module module-switch-on-port-available
That's all. I would post /etc/asound.conf, but it seems that from last update it doesn't exist.
Thank you for any help
Last edited by Eregus (2013-04-03 19:22:29)

Eregus wrote:
Yes, I use X.
And yes, I know what's the problem with Pulseaudio - the tip in Arch Wiki didn't help.
Edit: Oh, I only tried that workaround, I didn't try to change user. I'll edit mpd.conf when I come back home.
according to your config, you used that workaround wrongly. it will only work, if you point to the pulse server IP in mpd.conf. So add the server line in your pulse output. (its most likely 127.0.0.1)
Last edited by Rasi (2013-04-03 15:36:03)

[Solved] Alsa, no sound after hibernation

Hi,
Since few weeks, after resume from hibernate, I've not got sound.
I've to reboot the computer to have sound.
My kernel is 3.9.4.
# aplay -l
**** Liste des Périphériques Matériels PLAYBACK ****
carte 0: PCH [HDA Intel PCH], périphérique 0: VT1802 Analog [VT1802 Analog]
Sous-périphériques: 1/1
Sous-périphérique #0: subdevice #0
carte 0: PCH [HDA Intel PCH], périphérique 2: VT1802 Alt Analog [VT1802 Alt Analog]
Sous-périphériques: 1/1
Sous-périphérique #0: subdevice #0
carte 0: PCH [HDA Intel PCH], périphérique 3: HDMI 0 [HDMI 0]
Sous-périphériques: 1/1
Sous-périphérique #0: subdevice #0
How can I fix it ?
Thanks in advance.
Last edited by NeanderMarcl (2013-06-15 11:53:01)

chu887 wrote:
NeanderMarcl wrote:
Hi,
Since few weeks, after resume from hibernate, I've not got sound.
I've to reboot the computer to have sound.
My kernel is 3.9.4.
# aplay -l
**** Liste des Périphériques Matériels PLAYBACK ****
carte 0: PCH [HDA Intel PCH], périphérique 0: VT1802 Analog [VT1802 Analog]
Sous-périphériques: 1/1
Sous-périphérique #0: subdevice #0
carte 0: PCH [HDA Intel PCH], périphérique 2: VT1802 Alt Analog [VT1802 Alt Analog]
Sous-périphériques: 1/1
Sous-périphérique #0: subdevice #0
carte 0: PCH [HDA Intel PCH], périphérique 3: HDMI 0 [HDMI 0]
Sous-périphériques: 1/1
Sous-périphérique #0: subdevice #0
How can I fix it ?
Thanks in advance.
Does your headphone jack work? I have the same problem with the speaker , no sound from it at all, but the headphone works as normal.
My device is :
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: STAC9228 Analog [STAC9228 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: STAC9228 Digital [STAC9228 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
Headphones don't work

[solved] Typing error sound - after last update

Hey guys, after last update every time i make some mistake while typing on console (rxvt) or at the file search on gnome, this weird sound comes out from pc speaker (some eletric bizzz). I can't find anything related to this, does anyone knows if that is some kind of configuration of Xorg or it's a bug?
Thanks for any help!
Last edited by gvescovi (2009-08-11 02:27:25)

Hello Gvescovi!
What does it mean for misstyping? The speaker gives sound in such a cases.
You can disable it:
http://wiki.archlinux.org/index.php/Dis … eaker_beep

No speaker sound after unplugging the earphones

My IP4 now has no sound coming out from the speaker but through the earphone only. I tried to reboot/reset the phone or plug in or out again the earphone, but still not working. After I press the volume +/- buttons on the side, it displays it still on a earphone mode even I don't have the earphone plug in) Pls help.....

Create a folder on the desk top.
Open up the driver pack with winrar and extract the raw drivers to created folder.
In Dev Man click update driver and then point to have CD so you then get a list of devices for your sound card, there may be 2, either one will do.
Point the next steps to the folder with driver and try and force it.
GL

No speaker sound after loading Os 6

After I loaded Os 6 on my iPad 2 my speakers no longer produce any sound. The headphones still work

If you still have sound in the music and videos apps. You have system sounds muted.
If you lose sounds for keyboard clicks, games or other apps, email notifications and other notifications, system sounds may have been muted.
System sounds can be muted and controlled two different ways. The screen lock rotation can be controlled in the same manner as well.
Settings>General>Use Side Switch to: Mute System sounds. If this option is selected, the switch on the side of the iPad above the volume rocker will mute system sounds.
If you choose Lock Screen Rotation, then the switch locks the screen. If the screen is locked, you will see a lock icon in the upper right corner next to the battery indicator gauge.
If you have the side switch set to lock screen rotation then the system sound control is in the task bar. Double tap the home button and in the task bar at the bottom, swipe all the way to the right. The speaker icon is all the way to the left. Tap on it and system sounds will return.
If you have the side switch set to mute system sounds, then the screen lock rotation can be accessed via the task bar in the same manner as described above.
This support article from Apple explains how the side switch works.
http://support.apple.com/kb/HT4085

No speaker sound after upgrade to ios6

After upgrading to iOS 6 on my iPhone 4S, my speaker cuts in and out and gives no response to anything played out of the iPhone the speaker on the phone cuts in and out and is mostly unusable any tips out there for fixing this?

The same problem here, did you get a solution

[SOLVED] Vaio power usage after suspend/resume cycle

Hi,
I came to the conclusion my laptop (Sony Vaio VPCSB36FG/B) suffers from one particular issue:
After a suspend/resume cycle, the discrete card in the laptop (Radeon HD6470M) is powered on again, although /sys/kernel/debug/vgaswitcheroo/switch still reports the contrary.
This explains why the laptop is using ~5W more after a suspend/resume cycle. I can blacklist the radeon module on boot, but then the discrete card is powered on when the laptop is started. And since the module is blacklisted, there is no way to disable the card using vgaswitcheroo.
Unfortunately, blacklisting the module (on boot) and manually loading the module after boot, then switching the card off (using vgaswitcheroo) and removing the module results in either a display driver crash or the message: "radeon module is in use".
For the record, I'm using the open source driver for both cards (i915 & radeon).
My guess is, the only way to prevent the card from being powered on after a suspend/resume cycle is to make sure the radeon module is not enabled at all before suspending the laptop, but I'm wondering how to achieve this.
Any suggestions please?
Last edited by LordChaos73 (2013-01-16 20:48:21)

Okay, this workaround seems to work, at least manually:
1. Before suspending, the discrete card should be powered on (suspending seems to be a little slower now):
echo ON > /sys/kernel/debug/vgaswitcheroo/switch
2. After resume, one is able to turn off the discrete again:
echo OFF > /sys/kernel/debug/vgaswitcheroo/switch
Now I just need to figure out how to automate this in a nicely fashion.
Last edited by LordChaos73 (2013-01-16 20:49:06)

[SOLVED] NTFS partition unmounted after suspend to ram

I recently did a from-scratch installation after I bought an SSD to replace of my old harddrive. Since this fresh install I have been having a problem with an NTFS partition that is mounted by way of fstab (it's not _the_ windows partition just a bit of shared space on a dual-boot setup): Whenever I suspend the computer and bring it back up, the NTFS partition is invariably unmounted.
The mount point is empty and the mount command makes no mention of the mount. A simple "sudo mount /mnt/SAND" will bring the partition back up again although sometimes it needs to be umounted first (the mount point is still empty despite the 'mount'). Here is the fstab line:
/dev/sda3 /mnt/SAND ntfs-3g defaults,noatime,uid=1000,gid=100 0 0
Testing and screwing around I've noticed that if the WINDOWS partition is mounted using nautilus (as it is not mentioned in fstab) that too will be unmounted while a non-root ext4 partition (UBUNTU) is not.
So my hypothesis is that these NTFS partitions are singled out for unmounting when suspending (but apparently not mounting when reawakening?) -- maybe because they are assumed to be external drives? Given that it happens across mounting solutions (fstab/nautilus) I'm inclined to think it's not a bug?
At any rate I'm looking for a solution that will allow me to stop the unmounting when suspending -- ideally for all internal drives, secondarily for these specific partitions. I have checked the suspend to ram article on the wiki but it doesn't seem to mention anything about unmounting...
EDIT: After the Great Big Arch Switch To Systemd this problem no longers occurs on so I'm closing it. Not necessarily much of a solution to anyone who happens on this from google, sorry.
Last edited by madchine (2012-10-13 12:58:54)

Hi all,
It seems that most freezes are gone with:
- 270.29 beta driver
- MTRR enabled by appending enable_mtrr_cleanup mtrr_spare_reg_nr=1 to the list of kernel options (see http://www.nvnews.net/vbulletin/showpos … tcount=39)
I didn't investigate further to know if both the driver and the MTRR trick are required.
Thanks a lot,
Aurel.

[solved] No speaker sound after suspend

Similar Messages

Maybe you are looking for