[solved]Problems with 82801H (ICH8 Family) sound

Hi!
I've got some problems with my sound.
I read http://bbs.archlinux.org/viewtopic.php?id=50047 (adding options in modprobe.conf)
I tried http://wiki.archlinux.org/index.php/ALS … s_and_test
and followed http://wiki.archlinux.org/index.php/Len … X300#Sound
But for some reason I simply can't get any sound at all.
My laptop is a lenovo x61s with
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
The modules (same as first link), are loaded without problems.
I've run alsaconf, checked modprobe.conf and modprobe.d/sound, looks ok
I get the channels in alsamixer, and my regular user is a member of audio group.
Trying e.g. vlc gives no error, simply no sound..
Following the test (second link, with aplay), gives no error.. simply no sound
I can't find anything in the logs..
The card worked perfectly in both Ubuntu and Slackware... so I can't see why it shouldn't work in Arch..
Help : )
/Diddi
Last edited by diddi (2008-12-22 08:13:19)

Yeey I solved it!
It seems that snd-hda-intel module can't always recongnized what kind of soundcard you're using.
By supplying the correct model option to the module, I finally got my sound.
Available models are found in
http://www.mjmwired.net/kernel/Document … ration.txt
For my laptop it was "thinkpad" : )
Thx
/Diddi

Similar Messages

[solved] Problems with multiple applications running sound...

Multiple programs on my system are unable to use sound at the same time. When any two programs that are supposed to output sound run together, the program that started the output first prevents the other from outputing. I read the Wiki page on ALSA, but have had no luck so far in identifying the problem. I do believe that I am using alsa, as the sound of the program with sound does change as I adjust the alsa mixer volumes.
This started happening when I reinstalled arch this moring with XFCE (I needed to add more space to root partition and replace my DE, and fealt it would be easiest to just reinstall the OS.) In the few days I was using KDE, the sound worked fine. I also previously used Ubuntu on this system in which the sound worked fine.
I am inclined to believe that It is either something I have not configured properly (however I did not do anything to sound setup in the KDE install) or a package that did not install with XFCE, but does with KDE-base.
EDIT: Also, If the sounds are coming from the same application they can both play, IE I can hear 2 youtube videos at the same time but not a youtube video and VLC or Skype.
Last edited by unr3st (2011-05-31 08:26:28)

brebs wrote:
Run fuser.
Lots of info in my ~/.asoundrc
Here is the output,
[unrest@Uberschlecht ~]$ fuser -v /dev/snd/* /dev/dsp*
Specified filename /dev/dsp* does not exist.
USER PID ACCESS COMMAND
/dev/snd/controlC0: unrest 1423 F.... pulseaudio
unrest 1483 f.... xfce4-mixer-plu
unrest 1541 F.... plugin-containe
/dev/snd/pcmC0D0p: unrest 1541 F...m plugin-containe
/dev/snd/timer: unrest 1541 F.... plugin-containe
There are no process in /dev/dsp
It may be worth adding that I had no .asoundrc in my home directory
I have also just discovered that flash seems to be the program that causes the interferences, as VLC and Skype run fine together. I am going to try the instructions by Karol, reboot, and report the results.

Problem with content: 7 - Bad sound Data

When I do the following...
Voice = new Sound();
Voice.loadSound("test.mp3", true)
I get the error...
Problem with content: 7 - Bad sound Data
AND
Problem with content: 7 - The sound data format is not
recognized.
I am using the test.mp3 files that comes with Flash8.
Thanks!
Bob

OK. This combo works!
version flash Player 8
action script 2.0
Audio Stream: MP3, 128 kbps, Stereo best
Audio event: MP3, 128 kbps, Stereo best
Override sound settings (unchecked)
But this combo does not!!
version flash lite 2.0
action script 2.0
Audio Stream: MP3, 128 kbps, Stereo best
Audio event: MP3, 128 kbps, Stereo best
Override sound settings (unchecked)
Still get the error on all Nokias except Nokia 90 which gets
no error but just does not play the file

When Apple solve problems with new iTunes calendar sync with windows and outlook?

When Apple solve problems with new iTunes calendar sync with windows and outlook?

Anything Downloaded with a Particular Apple ID is tied to that Apple ID and Cannot be Merged or Transferred to a Different Apple ID
More Info here...
Apple ID FAQs > http://support.apple.com/kb/HT5622
If necessary...
Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact

Setting always changes by itself in my iPhone 5s, also every few calls I have to face a problem with a call without sound

Setting always changes by itself in my iPhone 5s, also every few calls I have to face a problem with a call without sound, battery becomes empty quickly

User troubleshooting steps as outlined in the manual are reset, restore, restore as new. Have you tried any of these?

[SOLVED]Problem with sound in HDMI

Hello good society of Arch
Now I have problems with sound from HDMI. I use Arch as an tvPc, wasting movies and tv shows on it. I use ALSA and it works well, except of a few files that I have, then there is picture but sound is either twisted or not played at all. It does not matter whether I use vlc or mplayer, I'm experiencing the same problem.
I have not found anything about this with google, other problems have been either hdmi sound working or not, not like it is with me, sometimes it works and sometimes it don't.
I know that the files are ok, I can play them in anther pc I have (also using Arch on that pc).
Does anybody know what the problem might be? What do I have to look at to find out what the problem is? This have been like this for some time now, but I haven't looked into it before, because I don't use TV that muts, but the wife does and when she stats blaming Arch, I have too do something about it.
I have never encountered problem with Arch that i cant solve by using this forum and google
Thanks
Last edited by Vaski (2010-08-21 01:08:42)

cleanrock wrote:I noticed i got no audio over hdmi on some video file which had a low audio bitrate, i solved it by resampling the sound to 48000 in ~/.mplayer/config :
af=resample=48000
I will look at this when i come home from work, thanks.
nTia89 wrote:have you already read our wiki ?
Yes i have, and sound is working, well most of the time.

[SOLVED] Problem with second SATA drive

My laptop has two hard drive bays, and just recently I added a second SATA drive (moved it from my old laptop) to the extra bay.
Now, anytime the second hard drive /dev/sdb has any heavy disk activity, it appears to cause a shutdown of the SATA port for the first drive (/dev/sda)! Though the second drive is still fine, and I can still write to it until the system crashes from the root drive (on /dev/sda) being shutdown.
If I don't mount and use the second drive, the first drive works just fine, and I can pound it with traffic without issue.
I can reproduce this problem by copying large amounts of data to drive 2.
This is when I get in my dmesg when the first SATA drive shuts down:
[ 3013.249525] ata1.00: exception Emask 0x0 SAct 0x7ff SErr 0x0 action 0x6 frozen
[ 3013.249532] ata1.00: failed command: READ FPDMA QUEUED
[ 3013.249539] ata1.00: cmd 60/08:00:78:b8:ba/00:00:24:00:00/40 tag 0 ncq 4096 in
[ 3013.249539] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 3013.249543] ata1.00: status: { DRDY }
[ 3013.249545] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249559] ata1.00: cmd 61/08:08:b8:60:7b/00:00:29:00:00/40 tag 1 ncq 4096 out
[ 3013.249559] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249562] ata1.00: status: { DRDY }
[ 3013.249564] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249568] ata1.00: cmd 61/08:10:c0:60:7b/00:00:29:00:00/40 tag 2 ncq 4096 out
[ 3013.249568] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249570] ata1.00: status: { DRDY }
[ 3013.249572] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249576] ata1.00: cmd 61/08:18:c8:60:7b/00:00:29:00:00/40 tag 3 ncq 4096 out
[ 3013.249576] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249578] ata1.00: status: { DRDY }
[ 3013.249580] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249585] ata1.00: cmd 61/08:20:48:12:d7/00:00:18:00:00/40 tag 4 ncq 4096 out
[ 3013.249585] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249587] ata1.00: status: { DRDY }
[ 3013.249589] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249593] ata1.00: cmd 61/08:28:28:63:38/00:00:19:00:00/40 tag 5 ncq 4096 out
[ 3013.249593] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249595] ata1.00: status: { DRDY }
[ 3013.249597] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249601] ata1.00: cmd 61/08:30:28:6f:38/00:00:19:00:00/40 tag 6 ncq 4096 out
[ 3013.249601] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249603] ata1.00: status: { DRDY }
[ 3013.249605] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249609] ata1.00: cmd 61/08:38:28:98:ae/00:00:25:00:00/40 tag 7 ncq 4096 out
[ 3013.249609] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249611] ata1.00: status: { DRDY }
[ 3013.249613] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249617] ata1.00: cmd 61/08:40:d8:79:3b/00:00:25:00:00/40 tag 8 ncq 4096 out
[ 3013.249617] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249619] ata1.00: status: { DRDY }
[ 3013.249621] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249625] ata1.00: cmd 61/08:48:08:98:b6/00:00:18:00:00/40 tag 9 ncq 4096 out
[ 3013.249625] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249627] ata1.00: status: { DRDY }
[ 3013.249629] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249633] ata1.00: cmd 61/08:50:10:98:36/00:00:19:00:00/40 tag 10 ncq 4096 out
[ 3013.249633] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249636] ata1.00: status: { DRDY }
[ 3013.249640] ata1: hard resetting link
[ 3013.575549] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3013.576784] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3013.578334] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3013.578588] ata1.00: configured for UDMA/133
[ 3013.592223] ata1.00: device reported invalid CHS sector 0
[ 3013.592233] ata1.00: device reported invalid CHS sector 0
[ 3013.592238] ata1.00: device reported invalid CHS sector 0
[ 3013.592242] ata1.00: device reported invalid CHS sector 0
[ 3013.592246] ata1.00: device reported invalid CHS sector 0
[ 3013.592250] ata1.00: device reported invalid CHS sector 0
[ 3013.592254] ata1.00: device reported invalid CHS sector 0
[ 3013.592258] ata1.00: device reported invalid CHS sector 0
[ 3013.592263] ata1.00: device reported invalid CHS sector 0
[ 3013.592267] ata1.00: device reported invalid CHS sector 0
[ 3013.592271] ata1.00: device reported invalid CHS sector 0
[ 3013.592302] sd 0:0:0:0: [sda]
[ 3013.592306] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592310] sd 0:0:0:0: [sda]
[ 3013.592313] Sense Key : 0xb [current] [descriptor]
[ 3013.592320] Descriptor sense data with sense descriptors (in hex):
[ 3013.592323] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592342] 00 00 00 00
[ 3013.592351] sd 0:0:0:0: [sda]
[ 3013.592353] ASC=0x0 ASCQ=0x0
[ 3013.592358] sd 0:0:0:0: [sda] CDB:
[ 3013.592361] cdb[0]=0x28: 28 00 24 ba b8 78 00 00 08 00
[ 3013.592376] end_request: I/O error, dev sda, sector 616216696
[ 3013.592414] sd 0:0:0:0: [sda]
[ 3013.592417] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592421] sd 0:0:0:0: [sda]
[ 3013.592423] Sense Key : 0xb [current] [descriptor]
[ 3013.592428] Descriptor sense data with sense descriptors (in hex):
[ 3013.592431] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592449] 00 00 00 00
[ 3013.592458] sd 0:0:0:0: [sda]
[ 3013.592460] ASC=0x0 ASCQ=0x0
[ 3013.592465] sd 0:0:0:0: [sda] CDB:
[ 3013.592467] cdb[0]=0x2a: 2a 00 29 7b 60 b8 00 00 08 00
[ 3013.592482] end_request: I/O error, dev sda, sector 695951544
[ 3013.592505] sd 0:0:0:0: [sda]
[ 3013.592508] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592512] sd 0:0:0:0: [sda]
[ 3013.592514] Sense Key : 0xb [current] [descriptor]
[ 3013.592519] Descriptor sense data with sense descriptors (in hex):
[ 3013.592522] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592540] 00 00 00 00
[ 3013.592549] sd 0:0:0:0: [sda]
[ 3013.592551] ASC=0x0 ASCQ=0x0
[ 3013.592556] sd 0:0:0:0: [sda] CDB:
[ 3013.592558] cdb[0]=0x2a: 2a 00 29 7b 60 c0 00 00 08 00
[ 3013.592572] end_request: I/O error, dev sda, sector 695951552
[ 3013.592583] sd 0:0:0:0: [sda]
[ 3013.592586] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592589] sd 0:0:0:0: [sda]
[ 3013.592592] Sense Key : 0xb [current] [descriptor]
[ 3013.592597] Descriptor sense data with sense descriptors (in hex):
[ 3013.592599] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592618] 00 00 00 00
[ 3013.592626] sd 0:0:0:0: [sda]
[ 3013.592628] ASC=0x0 ASCQ=0x0
[ 3013.592632] sd 0:0:0:0: [sda] CDB:
[ 3013.592635] cdb[0]=0x2a: 2a 00 29 7b 60 c8 00 00 08 00
[ 3013.592649] end_request: I/O error, dev sda, sector 695951560
[ 3013.592665] sd 0:0:0:0: [sda]
[ 3013.592668] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592671] sd 0:0:0:0: [sda]
[ 3013.592673] Sense Key : 0xb [current] [descriptor]
[ 3013.592678] Descriptor sense data with sense descriptors (in hex):
[ 3013.592684] Aborting journal on device dm-0-8.
[ 3013.592701] EXT4-fs error (device dm-0) in ext4_reserve_inode_write:4476: Journal has aborted
[ 3013.592687] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592723] 00 00 00 00
[ 3013.592729] sd 0:0:0:0: [sda]
[ 3013.592730] ASC=0x0 ASCQ=0x0
[ 3013.592733] sd 0:0:0:0: [sda] CDB:
[ 3013.592735] cdb[0]=0x2a: 2a 00 18 d7 12 48 00 00 08 00
[ 3013.592744] end_request: I/O error, dev sda, sector 416748104
[ 3013.592752] Buffer I/O error on device dm-0, logical block 266057
[ 3013.592760] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5902184 (offset 258048 size 4096 starting block 266057)
[ 3013.592766] sd 0:0:0:0: [sda]
[ 3013.592768] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592771] sd 0:0:0:0: [sda]
[ 3013.592772] Sense Key : 0xb [current] [descriptor]
[ 3013.592776] Descriptor sense data with sense descriptors (in hex):
[ 3013.592778] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592790] 00 00 00 00
[ 3013.592795] sd 0:0:0:0: [sda]
[ 3013.592797] ASC=0x0 ASCQ=0x0
[ 3013.592800] sd 0:0:0:0: [sda] CDB:
[ 3013.592801] cdb[0]=0x2a: 2a 00 19 38 63 28 00 00 08 00
[ 3013.592811] end_request: I/O error, dev sda, sector 423125800
[ 3013.592817] Buffer I/O error on device dm-0, logical block 1063269
[ 3013.592822] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5898577 (offset 970752 size 4096 starting block 1063269)
[ 3013.592842] sd 0:0:0:0: [sda]
[ 3013.592845] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592849] sd 0:0:0:0: [sda]
[ 3013.592851] Sense Key : 0xb [current] [descriptor]
[ 3013.592856] Descriptor sense data with sense descriptors (in hex):
[ 3013.592859] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592877] 00 00 00 00
[ 3013.592885] sd 0:0:0:0: [sda]
[ 3013.592887] ASC=0x0 ASCQ=0x0
[ 3013.592892] sd 0:0:0:0: [sda] CDB:
[ 3013.592894] cdb[0]=0x2a: 2a 00 19 38 6f 28 00 00 08 00
[ 3013.592908] end_request: I/O error, dev sda, sector 423128872
[ 3013.592915] Buffer I/O error on device dm-0, logical block 1063653
[ 3013.592922] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5902187 (offset 1171456 size 4096 starting block 1063653)
[ 3013.592931] sd 0:0:0:0: [sda]
[ 3013.592934] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592937] sd 0:0:0:0: [sda]
[ 3013.592940] Sense Key : 0xb [current] [descriptor]
[ 3013.592945] Descriptor sense data with sense descriptors (in hex):
[ 3013.592947] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592966] 00 00 00 00
[ 3013.592974] sd 0:0:0:0: [sda]
[ 3013.592976] ASC=0x0 ASCQ=0x0
[ 3013.592980] sd 0:0:0:0: [sda] CDB:
[ 3013.592983] cdb[0]=0x2a: 2a 00 25 ae 98 28 00 00 08 00
[ 3013.592997] end_request: I/O error, dev sda, sector 632199208
[ 3013.593006] Buffer I/O error on device dm-0, logical block 27197445
[ 3013.593018] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 6425165 (offset 151552 size 4096 starting block 27197445)
[ 3013.593028] sd 0:0:0:0: [sda]
[ 3013.593031] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593034] sd 0:0:0:0: [sda]
[ 3013.593037] Sense Key : 0xb [current] [descriptor]
[ 3013.593042] Descriptor sense data with sense descriptors (in hex):
[ 3013.593045] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593063] 00 00 00 00
[ 3013.593071] sd 0:0:0:0: [sda]
[ 3013.593073] ASC=0x0 ASCQ=0x0
[ 3013.593078] sd 0:0:0:0: [sda] CDB:
[ 3013.593085] EXT4-fs error (device dm-0) in ext4_reserve_inode_write:4476: Journal has aborted
[ 3013.593089] cdb[0]=0x2a: 2a 00 25 3b 79 d8 00 00 08 00
[ 3013.593104] end_request: I/O error, dev sda, sector 624654808
[ 3013.593111] Buffer I/O error on device dm-0, logical block 26254395
[ 3013.593115] lost page write due to I/O error on dm-0
[ 3013.593126] sd 0:0:0:0: [sda]
[ 3013.593129] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593132] sd 0:0:0:0: [sda]
[ 3013.593135] Sense Key : 0xb [current] [descriptor]
[ 3013.593140] Descriptor sense data with sense descriptors (in hex):
[ 3013.593142] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593161] 00 00 00 00
[ 3013.593169] sd 0:0:0:0: [sda]
[ 3013.593171] ASC=0x0 ASCQ=0x0
[ 3013.593175] sd 0:0:0:0: [sda] CDB:
[ 3013.593178] cdb[0]=0x2a: 2a 00 18 b6 98 08 00 00 08 00
[ 3013.593192] end_request: I/O error, dev sda, sector 414619656
[ 3013.593198] Buffer I/O error on device dm-0, logical block 1
[ 3013.593201] lost page write due to I/O error on dm-0
[ 3013.593211] sd 0:0:0:0: [sda]
[ 3013.593213] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593217] sd 0:0:0:0: [sda]
[ 3013.593219] Sense Key : 0xb [current] [descriptor]
[ 3013.593224] Descriptor sense data with sense descriptors (in hex):
[ 3013.593227] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593245] 00 00 00 00
[ 3013.593253] sd 0:0:0:0: [sda]
[ 3013.593256] ASC=0x0 ASCQ=0x0
[ 3013.593260] sd 0:0:0:0: [sda] CDB:
[ 3013.593262] cdb[0]=0x2a: 2a 00 19 36 98 10 00 00 08 00
[ 3013.593277] end_request: I/O error, dev sda, sector 423008272
[ 3013.593283] Buffer I/O error on device dm-0, logical block 1048578
[ 3013.593286] lost page write due to I/O error on dm-0
[ 3013.593298] ata1: EH complete
[ 3013.595707] EXT4-fs error (device dm-0) in ext4_dirty_inode:4603: Journal has aborted
[ 3013.596581] EXT4-fs error (device dm-0): ext4_journal_start_sb:370: Detected aborted journal
[ 3013.596591] EXT4-fs (dm-0): Remounting filesystem read-only
[ 3020.421558] journal commit I/O error
[ 3020.421570] journal commit I/O error
[ 3020.421574] journal commit I/O error
[ 3020.421578] journal commit I/O error
[ 3020.421581] journal commit I/O error
[ 3147.052191] ata1.00: exception Emask 0x0 SAct 0xf SErr 0x0 action 0x6 frozen
[ 3147.052197] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052209] ata1.00: cmd 60/50:00:d0:48:99/00:00:1c:00:00/40 tag 0 ncq 40960 in
[ 3147.052209] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 3147.052212] ata1.00: status: { DRDY }
[ 3147.052213] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052218] ata1.00: cmd 60/18:08:28:49:99/00:00:1c:00:00/40 tag 1 ncq 12288 in
[ 3147.052218] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052220] ata1.00: status: { DRDY }
[ 3147.052221] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052226] ata1.00: cmd 60/88:10:48:49:99/00:00:1c:00:00/40 tag 2 ncq 69632 in
[ 3147.052226] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052228] ata1.00: status: { DRDY }
[ 3147.052229] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052234] ata1.00: cmd 60/20:18:00:a4:ba/00:00:24:00:00/40 tag 3 ncq 16384 in
[ 3147.052234] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052236] ata1.00: status: { DRDY }
[ 3147.052239] ata1: hard resetting link
[ 3147.378368] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3148.066853] ata1.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[ 3148.069139] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3148.069393] ata1.00: configured for UDMA/133
[ 3148.080059] ata1.00: device reported invalid CHS sector 0
[ 3148.080066] ata1.00: device reported invalid CHS sector 0
[ 3148.080071] ata1.00: device reported invalid CHS sector 0
[ 3148.080075] ata1.00: device reported invalid CHS sector 0
[ 3148.080112] sd 0:0:0:0: [sda]
[ 3148.080114] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080117] sd 0:0:0:0: [sda]
[ 3148.080118] Sense Key : 0xb [current] [descriptor]
[ 3148.080123] Descriptor sense data with sense descriptors (in hex):
[ 3148.080125] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080136] 00 00 00 00
[ 3148.080140] sd 0:0:0:0: [sda]
[ 3148.080142] ASC=0x0 ASCQ=0x0
[ 3148.080145] sd 0:0:0:0: [sda] CDB:
[ 3148.080146] cdb[0]=0x28: 28 00 1c 99 48 d0 00 00 50 00
[ 3148.080156] end_request: I/O error, dev sda, sector 479807696
[ 3148.080170] sd 0:0:0:0: [sda]
[ 3148.080171] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080173] sd 0:0:0:0: [sda]
[ 3148.080175] Sense Key : 0xb [current] [descriptor]
[ 3148.080178] Descriptor sense data with sense descriptors (in hex):
[ 3148.080180] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080190] 00 00 00 00
[ 3148.080195] sd 0:0:0:0: [sda]
[ 3148.080196] ASC=0x0 ASCQ=0x0
[ 3148.080199] sd 0:0:0:0: [sda] CDB:
[ 3148.080200] cdb[0]=0x28: 28 00 1c 99 49 28 00 00 18 00
[ 3148.080209] end_request: I/O error, dev sda, sector 479807784
[ 3148.080216] sd 0:0:0:0: [sda]
[ 3148.080218] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080220] sd 0:0:0:0: [sda]
[ 3148.080221] Sense Key : 0xb [current] [descriptor]
[ 3148.080224] Descriptor sense data with sense descriptors (in hex):
[ 3148.080225] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080236] 00 00 00 00
[ 3148.080241] sd 0:0:0:0: [sda]
[ 3148.080242] ASC=0x0 ASCQ=0x0
[ 3148.080245] sd 0:0:0:0: [sda] CDB:
[ 3148.080246] cdb[0]=0x28: 28 00 1c 99 49 48 00 00 88 00
[ 3148.080254] end_request: I/O error, dev sda, sector 479807816
[ 3148.080267] sd 0:0:0:0: [sda]
[ 3148.080268] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080270] sd 0:0:0:0: [sda]
[ 3148.080272] Sense Key : 0xb [current] [descriptor]
[ 3148.080274] Descriptor sense data with sense descriptors (in hex):
[ 3148.080276] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080287] 00 00 00 00
[ 3148.080291] sd 0:0:0:0: [sda]
[ 3148.080293] ASC=0x0 ASCQ=0x0
[ 3148.080295] sd 0:0:0:0: [sda] CDB:
[ 3148.080296] cdb[0]=0x28: 28 00 24 ba a4 00 00 00 20 00
[ 3148.080305] end_request: I/O error, dev sda, sector 616211456
[ 3148.080315] ata1: EH complete
I have experimented, and found that if I turn off NCQ on the kernel command line in my bootloader (libata.force=noncq), that it takes longer before the problem occurs. Though, if I write enough to the second drive, it does still happen after a while, just greatly reduced its chances of happening.
Is it possible that the old drive (sdb) is causing the problem? I noticed that it is much noisier than I remember when the drive head moves around.
Another curiosity while I was trying to duplicate the problem:
- I start a large file copy from sda -> sdb
- At the same time in another terminal, I do "find / -print"
- When I hear the drive 2 head moving, it pauses the output of the "find" command.
Every time I hear the head move, I see the find output pause. Its almost like the drive seek on drive 2 causes the whole Sata controller to pause while the head moves. Very odd!
Anyone have any ideas? I think the next thing I will try is borrow a drive from another machine, and do the big write to it to see if I get the same results.
If it is of any help, here is some more info on the laptop:
lspci:
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09)
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5)
00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5)
00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5)
00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5)
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
01:00.0 VGA compatible controller: NVIDIA Corporation Device 1251 (rev a1)
01:00.1 Audio device: NVIDIA Corporation GF116 High Definition Audio Controller (rev a1)
07:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)
0d:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e)
13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01)
13:00.1 SD Host controller: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01)
19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
cat /proc/interrupts:
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
0: 50 0 0 0 0 0 0 0 IO-APIC-edge timer
1: 958 0 0 0 0 0 0 0 IO-APIC-edge i8042
8: 1 0 0 0 0 0 0 0 IO-APIC-edge rtc0
9: 1675 0 0 0 0 0 0 0 IO-APIC-fasteoi acpi
12: 12257 0 0 0 0 0 0 0 IO-APIC-edge i8042
16: 24769 0 0 0 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb1, mmc0, nvidia
17: 142 0 0 0 0 0 0 0 IO-APIC-fasteoi snd_hda_intel
19: 0 0 0 0 0 0 0 0 IO-APIC-fasteoi rts_pstor
23: 1937 0 0 0 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb4
41: 1 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
42: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
43: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
44: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
45: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
46: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
47: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
48: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
49: 19406 0 0 0 0 0 0 0 PCI-MSI-edge iwlwifi
50: 36099 0 0 0 0 0 0 0 PCI-MSI-edge ahci
51: 14 0 0 0 0 0 0 0 PCI-MSI-edge mei
52: 386378 0 0 0 0 0 0 0 PCI-MSI-edge snd_hda_intel
53: 56803 0 0 0 0 0 0 0 PCI-MSI-edge eth0
NMI: 34 5 19 5 18 4 13 4 Non-maskable interrupts
LOC: 77964 17705 161241 14302 187823 16150 56845 12750 Local timer interrupts
SPU: 0 0 0 0 0 0 0 0 Spurious interrupts
PMI: 34 5 19 5 18 4 13 4 Performance monitoring interrupts
IWI: 0 0 0 0 0 0 0 0 IRQ work interrupts
RTR: 7 0 0 0 0 0 0 0 APIC ICR read retries
RES: 13721 7023 304 110 175 110 213 123 Rescheduling interrupts
CAL: 6941 7677 2774 7670 5804 7568 7655 7673 Function call interrupts
TLB: 366 545 268 179 310 272 212 166 TLB shootdowns
TRM: 0 0 0 0 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 0 0 0 0 Threshold APIC interrupts
MCE: 0 0 0 0 0 0 0 0 Machine check exceptions
MCP: 29 29 29 29 29 29 29 29 Machine check polls
ERR: 0
MIS: 0
smartctl --all /dev/sda
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.3-1-ARCH] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST9500423AS
Serial Number: 5WS354LM
LU WWN Device Id: 5 000c50 044bb741b
Firmware Version: 0005DEM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Sep 13 15:26:14 2012 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 105) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 113 099 006 Pre-fail Always - 54715920
3 Spin_Up_Time 0x0003 098 098 085 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1114
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 10214892
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 2030
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 559
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 8590065667
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 053 049 045 Old_age Always - 47 (Min/Max 47/51)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 17
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 871
193 Load_Cycle_Count 0x0032 039 039 000 Old_age Always - 122293
194 Temperature_Celsius 0x0022 047 051 000 Old_age Always - 47 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 113 099 000 Old_age Always - 54715920
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 67229123085518
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1947733828
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2798982459
254 Free_Fall_Sensor 0x0032 001 001 000 Old_age Always - 899
SMART Error Log Version: 1
ATA Error Count: 8 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:21:04.124 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
Error 7 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
ec 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:21:04.124 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
Error 6 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
Error 5 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
2f 00 01 10 00 00 a0 00 05:20:58.724 READ LOG EXT
Error 4 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
2f 00 01 10 00 00 a0 00 05:20:58.724 READ LOG EXT
61 00 08 ff ff ff 4f 00 05:20:58.724 WRITE FPDMA QUEUED
61 00 08 ff ff ff 4f 00 05:20:58.724 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6 -
# 2 Short offline Aborted by host 90% 1 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl --all /dev/sdb
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.3-1-ARCH] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint M6
Device Model: SAMSUNG HM320JI
Serial Number: S16LJF0QB02815
LU WWN Device Id: 5 0f0000 001202815
Firmware Version: 2SS00_01
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Thu Sep 13 15:27:10 2012 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 110) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 110) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 252 252 025 Pre-fail Always - 2562
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 810
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 4842
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 440
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 154
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 71
194 Temperature_Celsius 0x0022 073 073 000 Old_age Always - 55 (Min/Max 17/55)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x0032 252 252 000 Old_age Always - 0
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 534
225 Load_Cycle_Count 0x0032 077 077 000 Old_age Always - 236803
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Last edited by johni (2012-09-16 00:46:54)

It appears my drive one really is failing. It was the first drive and not the second making the loud head seek sound. I borrowed another drive from a friend, and copied my drive one to it. No problems with the new drive in place.

[Solved] Problem with mouse cursor gnome3

Hi
I moved back to Archlinux after a brief stay in LMDE, and test the new GNOME3, I am unpleasantly surprised that after a while the mouse is moving himself toward the top of the screen. I searched the internet, and seems to be a problem with the gnome-shell for some time, but I am not able to find the solution.
Momentarily solved by restarting gnome with ALT + F2 + r + Enter, but after a while, same thing happens again.
Can be well with photography programs, but of course if you do not solve this issue, GNOME, I can not use
Can you give me a helping hand?
Thanks and regards
Rafa
Last edited by Warper4 (2011-08-16 18:09:50)

I don't know about Gnome, but my laptop had that problem. I tracked it down the 3d accelerometer being used to simulate a joystick. Of course, I also had (previously) set up another joystick to operate as a mouse. In the end, the cursor "drifted" when the laptop was not level
YMMV

[SOLVED] Problem with MPD and ALSA

Hello, I'm having problems with mpd using alsa output.
My alsa system works, I can play mp3 using mplayer -ao alsa, and flash plugin plays sound, my user (and also mpd user)is in the audio group.
But then mpd can't open the alsa device.
If I tell mpd to autodetect audio, it can't find anything:
(Running as root to see output, if using /etc/rc.d/mpd start, it just fails)
output: No "audio_output" defined in config file
output: Attempt to detect audio output device
output: Attempting to detect a alsa audio device
ALSA lib confmisc.c:768:(parse_card) cannot find card '0'
ALSA lib conf.c:4184:(_snd_config_evaluate) function snd_func_card_driver returned error: No such file or directory
ALSA lib confmisc.c:392:(snd_func_concat) error evaluating strings
ALSA lib conf.c:4184:(_snd_config_evaluate) function snd_func_concat returned error: No such file or directory
ALSA lib confmisc.c:1251:(snd_func_refer) error evaluating name
ALSA lib conf.c:4184:(_snd_config_evaluate) function snd_func_refer returned error: No such file or directory
ALSA lib conf.c:4663:(snd_config_expand) Evaluate error: No such file or directory
ALSA lib pcm.c:2212:(snd_pcm_open_noupdate) Unknown PCM default
alsa: Error opening default ALSA device: No such file or directory
output: Attempting to detect a oss audio device
oss: Error opening OSS device "/dev/dsp": No such file or directory
oss: Error opening OSS device "/dev/sound/dsp": No such file or directory
output: Attempting to detect a pulse audio device
mpd: src/output/pulse_output_plugin.c:400: pulse_output_wait_connection: Assertion `po->mainloop != ((void *)0)' failed.
and if I set up a basic alsa config...
audio_output {
type "alsa"
name "HDA-Intel"
It starts, but then playing anything:
% mpc play
Caspian - La Cerva
[paused] #2/10 0:00/4:59 (0%)
volume: n/a repeat: off random: off single: off consume: off
ERROR: problems opening audio device
mpc.log output:
ALSA lib confmisc.c:768:(parse_card) cannot find card '0'
ALSA lib conf.c:4184:(_snd_config_evaluate) function snd_func_card_driver returned error: No such file or directory
ALSA lib confmisc.c:392:(snd_func_concat) error evaluating strings
ALSA lib conf.c:4184:(_snd_config_evaluate) function snd_func_concat returned error: No such file or directory
ALSA lib confmisc.c:1251:(snd_func_refer) error evaluating name
ALSA lib conf.c:4184:(_snd_config_evaluate) function snd_func_refer returned error: No such file or directory
ALSA lib conf.c:4663:(snd_config_expand) Evaluate error: No such file or directory
ALSA lib pcm.c:2212:(snd_pcm_open_noupdate) Unknown PCM default
Sep 22 10:08 : output: Failed to open "HDA-Intel" [alsa]: Failed to open ALSA device "default": No such file or directory
I tried with different device and mixer settings and the error is always the same. It can't open alsa device.
Any Ideas?
Thank you.
Last edited by xzakox (2011-09-22 20:04:33)

Check that mpd is really being run as the mpd user, and that id lists audio for the mpd user. Also post your whole mpd.conf and the output from amixer when running as the user you run mpd as.
Last edited by Mr.Elendig (2011-09-22 11:43:35)

[SOLVED] Problem with Vuze and Java RE x86_64

Hello all !
First of all, sorry if this issue was posted before, but find no related issue similar to mine.
Using pacman, I successfully installed JRE (version 6u16-1-x86_64) and Vuze (version 4.2.0.8-1, former Azureus), but Vuze doesn't want to start.
Running the Vuze's executable in the gnome-terminal, I notice messages from vuze informing it can't find Java executable ("Java exec not found in PATH, starting auto-search..." AND "OOPS, unable to locate java exec in /usr/java/latest /usr/java /usr/lib/jvm/latest /usr/lib/jvm hierarchy") and therefore cannot start the Vuze UI. I also tried but failed in verify the version of Java with the command "java -version" due to command not found.
What is the best approach to fix this problem with Java 64 bits?
Thanks in advance
Last edited by josephg (2009-09-28 18:55:56)

peart wrote:Just log out and back in, most likely. There are scripts in /etc/profile.d/ that need to be run to set up your java environment. They get run automatically when you log in.
Yep, perfect answer - issue solved. Thanks a lot!

[SOLVED] Problem with symlinking and PKGBUILD

Hello Everyone,
I have created the javafx-sdk package on AUR, and make the installation a lot simplier. But I am having a problem with the creationg of the symlink.
So I have 1 binary file "javafxpackager" in the "bin" folder that I need to symlink into /usr/bin. This is the method I am using
mkdir -p ${pkgdir}/usr/bin
chmod +x ${pkgdir}/usr/lib/jvm/${pkgname}/bin/javafxpackager
ln -s ${pkgdir}/usr/lib/jvm/${pkgname}/bin/javafxpackager ${pkgdir}/usr/bin/javafxpackager
My problem is that this method doesn't work at all. The only way to me after the installation to make the symlink working is by doing this :
ls chmod +x /usr/lib/jvm/javafx-sdk/bin/javafxpackager
sudo ln -s /usr/lib/jvm/javafx-sdk/bin/javafxpackager /usr/bin/
In order to make it work.
How can I solve this problem ?
Thanks in Advance,
Luis Da Costa
Last edited by aliasbody (2012-06-26 00:27:15)

Problem solved ! Here's how to do it :
mkdir -p ${pkgdir}/usr/bin
chmod +x ${pkgdir}/usr/lib/jvm/${pkgname}/bin/javafxpackager
ln -s /usr/lib/jvm/javafx-sdk/bin/javafxpackager ${pkgdir}/usr/bin/javafxpackager
I didn't know, but you can symlink a file that doesn't exist yet, and this is what I did. I use and non existing (yet) javafxpackager binary from the non existing (yet) "/usr/lib/jvm/javafx-sdk/bin/" folder, and send it to the ${pkgdir}/usr/bin/javafxpackager, that will be copied into the original "/usr/bin/" folder.
So this problem is solved and I'm happy
(PS : thanks @ngoonee and @Trilby for you help ! Thanks to you I found out a little bit faster where the problem was ^^)

[SOLVED] Problem with "su" and "login".

Hi, I reinstalled Arch Linux today when I updated "filesystem" and reboot appeared an error with root device, but I solved with installation CD.
I restarted laptop after solving error with root device when I went to XFCE4 and open a terminal I tried to login as root with "su" and "su -" but showed this error:
bash: su: command not found
So I rebooted to start in text mode.
When loaded SLIM I press ctrl+alt+F1 to enter text mode.
I type root to login but did'nt appear to enter the pass, appeared again to enter login. I tried type my user but did the same.
Someone can help me?
Thanks!
Last edited by surrealistic (2012-10-12 08:54:58)

Thank you falconindy. I upgrade with --force because I search in Google the problem show "filesystem" when I tried install and I read that solution is upgrade "filesystem" with --foce.
I tried to reinstall util-linux and now works. Thank you!

[SOLVED]problem with Bumblebee and Kernel 3.11-1-2

Hi!
I'm having problems with Bumblebee from Kernel 3.10 but I read that Kernel 3.11 solved the problem, I searched and tried possible solutions to my problem unsuccessfully
The message shows me when I run "optirun":
[ 5454.262739] [ERROR]Cannot access secondary GPU - error: [XORG] (EE) No devices detected.
[ 5454.262776] [ERROR]Aborting because fallback start is disabled.
I've tried with wiki's solutions, forums solutions...
Configurations files:
/etc/bumblebee/bumblebee.conf:
# Configuration file for Bumblebee. Values should **not** be put between quotes
## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d
## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=virtualgl
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/primus:/usr/lib32/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false
# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods
## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/nvidia:/usr/lib32/nvidia
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia/xorg/,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau
/etc/bumblebee/xorg.conf.nvidia
Section "ServerLayout"
Identifier "Layout0"
Option "AutoAddDevices" "false"
Option "AutoAddGPU" "false"
EndSection
Section "Device"
Identifier "DiscreteNvidia"
Driver "nvidia"
VendorName "NVIDIA Corporation"
# If the X server does not automatically detect your VGA device,
# you can manually set it here.
# To get the BusID prop, run `lspci | egrep 'VGA|3D'` and input the data
# as you see in the commented example.
# This Setting may be needed in some platforms with more than one
# nvidia card, which may confuse the proprietary driver (e.g.,
# trying to take ownership of the wrong device). Also needed on Ubuntu 13.04.
BusID "PCI:01:00.0"
# Setting ProbeAllGpus to false prevents the new proprietary driver
# instance spawned to try to control the integrated graphics card,
# which is already being managed outside bumblebee.
# This option doesn't hurt and it is required on platforms running
# more than one nvidia graphics card with the proprietary driver.
# (E.g. Macbook Pro pre-2010 with nVidia 9400M + 9600M GT).
# If this option is not set, the new Xorg may blacken the screen and
# render it unusable (unless you have some way to run killall Xorg).
Option "ProbeAllGpus" "false"
Option "NoLogo" "true"
Option "UseEDID" "false"
Option "UseDisplayDevice" "none"
EndSection
lspci |grep NVIDIA:
01:00.0 VGA compatible controller: NVIDIA Corporation GK107M [GeForce GT 640M] (rev a1)
I hope can help me
Thanks!
Last edited by surrealistic (2013-11-04 18:46:35)

My /var/log/Xorg.8.log:
[ 337.161]
X.Org X Server 1.14.4
Release Date: 2013-10-31
[ 337.161] X Protocol Version 11, Revision 0
[ 337.161] Build Operating System: Linux 3.11.6-1-ARCH x86_64
[ 337.161] Current Operating System: Linux h131h-laptop 3.11.6-1-ARCH #1 SMP PREEMPT Fri Oct 18 23:22:36 CEST 2013 x86_64
[ 337.161] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=4eb69984-2228-4aba-9863-28a7fa854e51 rw quiet
[ 337.161] Build Date: 01 November 2013 05:10:48PM
[ 337.161]
[ 337.161] Current version of pixman: 0.30.2
[ 337.161] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 337.161] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 337.161] (==) Log file: "/var/log/Xorg.8.log", Time: Mon Nov 4 14:20:04 2013
[ 337.161] (++) Using config file: "/etc/bumblebee/xorg.conf.nvidia"
[ 337.161] (++) Using config directory: "/etc/bumblebee/xorg.conf.d"
[ 337.161] (==) ServerLayout "Layout0"
[ 337.161] (==) No screen section available. Using defaults.
[ 337.161] (**) |-->Screen "Default Screen Section" (0)
[ 337.161] (**) | |-->Monitor "<default monitor>"
[ 337.161] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 337.161] (**) | |-->Device "DiscreteNvidia"
[ 337.161] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 337.161] (**) Option "AutoAddDevices" "false"
[ 337.161] (**) Option "AutoAddGPU" "false"
[ 337.161] (**) Not automatically adding devices
[ 337.161] (==) Automatically enabling devices
[ 337.161] (**) Not automatically adding GPU devices
[ 337.161] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 337.162] Entry deleted from font path.
[ 337.162] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 337.162] Entry deleted from font path.
[ 337.162] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 337.162] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 337.162] Entry deleted from font path.
[ 337.162] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 337.162] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 337.162] (++) ModulePath set to "/usr/lib/nvidia/xorg/,/usr/lib/xorg/modules"
[ 337.162] (==) |-->Input Device "<default pointer>"
[ 337.162] (==) |-->Input Device "<default keyboard>"
[ 337.162] (==) The core pointer device wasn't specified explicitly in the layout.
Using the default mouse configuration.
[ 337.162] (==) The core keyboard device wasn't specified explicitly in the layout.
Using the default keyboard configuration.
[ 337.162] (II) Loader magic: 0x7fdc20
[ 337.162] (II) Module ABI versions:
[ 337.162] X.Org ANSI C Emulation: 0.4
[ 337.162] X.Org Video Driver: 14.1
[ 337.162] X.Org XInput driver : 19.1
[ 337.162] X.Org Server Extension : 7.0
[ 337.162] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 337.162] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 337.162] setversion 1.4 failed
[ 337.163] (--) PCI:*(0:1:0:0) 10de:0fd2:1025:0648 rev 161, Mem @ 0xb2000000/16777216, 0xa0000000/268435456, 0xb0000000/33554432, I/O @ 0x00002000/128
[ 337.163] Initializing built-in extension Generic Event Extension
[ 337.163] Initializing built-in extension SHAPE
[ 337.163] Initializing built-in extension MIT-SHM
[ 337.163] Initializing built-in extension XInputExtension
[ 337.163] Initializing built-in extension XTEST
[ 337.163] Initializing built-in extension BIG-REQUESTS
[ 337.163] Initializing built-in extension SYNC
[ 337.163] Initializing built-in extension XKEYBOARD
[ 337.163] Initializing built-in extension XC-MISC
[ 337.163] Initializing built-in extension SECURITY
[ 337.163] Initializing built-in extension XINERAMA
[ 337.163] Initializing built-in extension XFIXES
[ 337.163] Initializing built-in extension RENDER
[ 337.163] Initializing built-in extension RANDR
[ 337.164] Initializing built-in extension COMPOSITE
[ 337.164] Initializing built-in extension DAMAGE
[ 337.164] Initializing built-in extension MIT-SCREEN-SAVER
[ 337.164] Initializing built-in extension DOUBLE-BUFFER
[ 337.164] Initializing built-in extension RECORD
[ 337.164] Initializing built-in extension DPMS
[ 337.164] Initializing built-in extension X-Resource
[ 337.164] Initializing built-in extension XVideo
[ 337.164] Initializing built-in extension XVideo-MotionCompensation
[ 337.164] Initializing built-in extension XFree86-VidModeExtension
[ 337.164] Initializing built-in extension XFree86-DGA
[ 337.164] Initializing built-in extension XFree86-DRI
[ 337.164] Initializing built-in extension DRI2
[ 337.164] (II) LoadModule: "glx"
[ 337.164] (II) Loading /usr/lib/nvidia/xorg/modules/extensions/libglx.so
[ 337.172] (II) Module glx: vendor="NVIDIA Corporation"
[ 337.172] compiled for 4.0.2, module version = 1.0.0
[ 337.172] Module class: X.Org Server Extension
[ 337.172] (II) NVIDIA GLX Module 325.15 Wed Jul 31 18:12:00 PDT 2013
[ 337.172] Loading extension GLX
[ 337.172] (II) LoadModule: "nvidia"
[ 337.172] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 337.172] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 337.172] compiled for 4.0.2, module version = 1.0.0
[ 337.172] Module class: X.Org Video Driver
[ 337.172] (II) LoadModule: "mouse"
[ 337.172] (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
[ 337.172] (II) Module mouse: vendor="X.Org Foundation"
[ 337.172] compiled for 1.14.0, module version = 1.9.0
[ 337.172] Module class: X.Org XInput Driver
[ 337.172] ABI class: X.Org XInput driver, version 19.1
[ 337.172] (II) LoadModule: "kbd"
[ 337.173] (WW) Warning, couldn't open module kbd
[ 337.173] (II) UnloadModule: "kbd"
[ 337.173] (II) Unloading kbd
[ 337.173] (EE) Failed to load module "kbd" (module does not exist, 0)
[ 337.173] (II) NVIDIA dlloader X Driver 325.15 Wed Jul 31 17:50:57 PDT 2013
[ 337.173] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 337.173] (--) using VT number 1
[ 337.173] (II) Loading sub module "fb"
[ 337.173] (II) LoadModule: "fb"
[ 337.173] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 337.173] (II) Module fb: vendor="X.Org Foundation"
[ 337.173] compiled for 1.14.4, module version = 1.0.0
[ 337.173] ABI class: X.Org ANSI C Emulation, version 0.4
[ 337.173] (WW) Unresolved symbol: fbGetGCPrivateKey
[ 337.173] (II) Loading sub module "wfb"
[ 337.173] (II) LoadModule: "wfb"
[ 337.173] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 337.173] (II) Module wfb: vendor="X.Org Foundation"
[ 337.173] compiled for 1.14.4, module version = 1.0.0
[ 337.173] ABI class: X.Org ANSI C Emulation, version 0.4
[ 337.173] (II) Loading sub module "shadow"
[ 337.173] (II) LoadModule: "shadow"
[ 337.173] (II) Loading /usr/lib/xorg/modules/libshadow.so
[ 337.173] (II) Module shadow: vendor="X.Org Foundation"
[ 337.173] compiled for 1.14.4, module version = 1.1.0
[ 337.173] ABI class: X.Org ANSI C Emulation, version 0.4
[ 337.173] (II) Loading sub module "ramdac"
[ 337.173] (II) LoadModule: "ramdac"
[ 337.173] (II) Module "ramdac" already built-in
[ 337.174] (II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 337.174] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 337.174] (==) NVIDIA(0): RGB weight 888
[ 337.174] (==) NVIDIA(0): Default visual is TrueColor
[ 337.174] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 337.174] (**) NVIDIA(0): Option "NoLogo" "true"
[ 337.174] (**) NVIDIA(0): Option "ProbeAllGpus" "false"
[ 337.174] (**) NVIDIA(0): Option "UseEDID" "false"
[ 337.174] (**) NVIDIA(0): Option "UseDisplayDevice" "none"
[ 337.174] (**) NVIDIA(0): Enabling 2D acceleration
[ 337.174] (**) NVIDIA(0): Ignoring EDIDs
[ 337.174] (**) NVIDIA(0): Option "UseDisplayDevice" set to "none"; enabling NoScanout
[ 337.174] (**) NVIDIA(0): mode
[ 341.309] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0. Please
[ 341.309] (EE) NVIDIA(0): check your system's kernel log for additional error
[ 341.309] (EE) NVIDIA(0): messages and refer to Chapter 8: Common Problems in the
[ 341.309] (EE) NVIDIA(0): README for additional information.
[ 341.309] (EE) NVIDIA(0): Failed to initialize the NVIDIA graphics device!
[ 341.309] (EE) NVIDIA(0): Failing initialization of X screen 0
[ 341.309] (II) UnloadModule: "nvidia"
[ 341.309] (II) UnloadSubModule: "shadow"
[ 341.309] (II) UnloadSubModule: "wfb"
[ 341.309] (II) UnloadSubModule: "fb"
[ 341.309] (EE) Screen(s) found, but none have a usable configuration.
[ 341.309] (EE)
Fatal server error:
[ 341.309] (EE) no screens found(EE)
[ 341.309] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 341.309] (EE) Please also check the log file at "/var/log/Xorg.8.log" for additional information.
[ 341.309] (EE)
[ 341.309] (EE) Server terminated with error (1). Closing log file.
dmesg |grep bbswitch:
[ 13.570577] bbswitch: version 0.7
[ 13.570585] bbswitch: Found integrated VGA device 0000:00:02.0: \_SB_.PCI0.GFX0
[ 13.570591] bbswitch: Found discrete VGA device 0000:01:00.0: \_SB_.PCI0.PEG0.PEGP
[ 13.570687] bbswitch: detected an Optimus _DSM function
[ 13.570741] bbswitch: Succesfully loaded. Discrete card 0000:01:00.0 is on
[ 13.572354] bbswitch: disabling discrete graphics
[ 261.419114] bbswitch: enabling discrete graphics
[ 278.445698] bbswitch: disabling discrete graphics
[ 279.055257] bbswitch: enabling discrete graphics
[ 286.292315] bbswitch: disabling discrete graphics
[ 291.911052] bbswitch: enabling discrete graphics
[ 310.011289] bbswitch: disabling discrete graphics
[ 336.982794] bbswitch: enabling discrete graphics
[ 349.526470] bbswitch: enabling discrete graphics
I used "rcutree" option as shown in the post that you put, but I've deleted all changes made to use default configurations, because the solution of the post didn't work

[SOLVED] Problem with UTC and CST

I probably made a mistake while installing Arch Linux and the clocks in my computer are all a mess.
Right now the UTC time its 6+ hours, I changed it in the bios to the right hour but that give me -6 hours in the local time thats displayed in Arch Linux and gave me the right hour in Windows 7.
timedatectl
Local time: Fri 2013-12-20 12:33:12 CST
Universal time: Fri 2013-12-20 18:33:12 UTC
RTC time: Fri 2013-12-20 18:33:12
Timezone: America/Mexico_City (CST, -0600)
NTP enabled: yes
NTP synchronized: yes
RTC in local TZ: no
DST active: no
Last DST change: DST ended at
Sun 2013-10-27 01:59:59 CDT
Sun 2013-10-27 01:00:00 CST
Next DST change: DST begins (the clock jumps one hour forward) at
Sun 2014-04-06 01:59:59 CST
Sun 2014-04-06 03:00:00 CDT
PS: Already did everything in the wiki and tried with some [SOLVED] posts.
Edit: The problem with this its that when i use Windows 7 (to play DotA... or using the iPod, since no player can edit the files in the ipod) the hour is 6+ hours, that causes problems with the configuration in the ipod since each time i connect it the clock (that its also my only clock) changes to 6+ hours. Its maybe irrelevant for someone but i would like to have the right hour in all my systems.
Last edited by Senketsu (2013-12-20 19:16:54)

I am with Scimmia, everything looks correct. But, If you boot Windows, it will try to change the BIOS clock to local time unless you tell it otherwise.
Edit for both of your edits. Yes, fix windows
Last edited by ewaller (2013-12-20 18:56:32)

[SOLVED] Problem with modules and udev

Hi everybody,
I've been configuring Arch on my new laptop the last few days and today as I was going to perform the first backup, I noticed that my external HDD does not show up in /dev/ when I plug it in. I figured it could be a problem with udev and the fact that in my /etc/rc.conf I use MOD_AUTOLOAD="no" with an explicit list of MODULES generated with hwdetect (as suggested in the wiki).
To "solve" this I just changed MOD_AUTOLOAD to "yes" and after a reboot everything worked fine.
My questions are:
1) Is it possible to keep that feature (udev detects usb drives and creates the corresponding /dev/sdX) while having MOD_AUTOLOAD="no" ? What is/are the appropriate module(s) I have to put in my MODULES array ?
2) What other such "basic" MODULES could be very useful that hwdetect does not tell about.
Sorry for any English mistakes (I'm not a native speaker) and thank you in advance for your help,
yms
Last edited by yms (2010-01-06 12:48:20)

1) Thank you, it works perfectly.
2) Yes I know the question is weird. The thing is I have no precise idea at the moment and I just wanted to know if there are other very widely used features such as the one described in 1) that hwdetect ommits and that has to be loaded in MODULES.
Anyway, thank you very much, I consider this matter [solved]

[solved]Problems with 82801H (ICH8 Family) sound

Similar Messages

Maybe you are looking for