[solved] Question about the Hardware Abstraction Layer (HAL)

Does hal change xorg.conf to xorg.conf.d when enabled in the daemons section?
Last edited by digitalphoenix (2010-09-28 22:34:01)

No.
http://www.archlinux.org/news/xorg-18-moves-to-extra/

Similar Messages

Question about the hardware installat

I just picked up the Creative SoundBlaster X-Fi XtremeGamer, and upon [attempted] installation, I noticed a couple things that I didn't expect.
First, I noticed a rather large "AUX IN" connector on the top side of the card. I did some research, and apparently that is supposed to connect to my optical dri've. Thing is, I don't have a cable that is able to do this, nor did the sound card come with one (the optical dri've didn't either, it was OEM). Is this necessary? What is the point of this? I'm currently using my onboard sound, and nothing from my optical dri've is connected out of it's 4-pin connector, and my sound is fine. Here's a picture:
http://img295.imageshack.us/img295/7899/auxinhz4.jpg
Second, I noticed an 8-pin "SPDIF_0" section at the far right side of the card. Again I did some research, and it's for digital audio or something like that. To be blunt, I'm not sure what do to with it, or what from my system goes on those pins.
Third and last, I noted a small, unnamed 2-pin set just above the "SPDIF_0" pins. Again, I have not the slightest clue as to what I have to do with these.
Here is a picture of both the "SPDIF_0" and unnamed 2-pin sets:
http://img20.imageshack.us/img20/6500/portshc7.jpg
Thanks in advance! Can't wait to use this card.

You don't need to do anything with any of those connections. Connecting the optical dri've to the card is never done anymore, the S/PDIF connection is for digital audio to the front bay (which you don't have) and the two pin connection is probably where you put the jumper for the mic (as stated in the creative manuals, not sure why it's even needed).

Question about the CSS behavior when using layer 3 sticky and sticky table

Hi everyone,
I have a question about the CSS behavior when using layer 3 sticky and sticky table is full.
If I configure layer 3 sticky and specify the inactivity timeout as below, how does the CSS
handle subsequent needed sticky requests ?
advanced-balance sticky-srcip
sticky-inact-timeout 30
CSS document says that
Note:
If you use the sticky-inact-timeout command to specify the inactivity timeout
period on a sticky connection, when the sticky table becomes full and none of
the entries have expired from the sticky table, the CSS rejects subsequent
needed sticky requests.
My question is what is the next reaction by doing the CSS if the CSS is in the
following condition:
when the sticky table becomes full and none of the entries have expired from
the sticky table, the CSS rejects subsequent needed sticky requests
Does CSS just rejects/drops subsequent needed sticky requests ?
or
Does CSS does not stick subsequence requests to particular service but CSS forward
subsequence requests with round-robin basis ? which means if the sticky table is full,
the CSS just works round-robin load balancing fashion for subsequence requests ?
Your information would be appreciated.
Best regards,

Hello,
There is a good document explaining this on Cisco web site
http://www.cisco.com/en/US/products/hw/contnetw/ps789/products_tech_note09186a0080094b4b.shtml
It depends if the sticky-inact-timeout is used or not. If not, it's FIFO (the oldest entry in the sticky table is removed). If yes, the CSS will reject the next sticky request.
Rgds,
Gaetan
Rgds
Gaetan

Question about the sensor... just got my 4s yesterday after screwing up my 3 with the laterd version update. EVery call I have been on has either changed to speaker, called another number or ended the call or activated facetime, which I have turned off.

Question about the sensor... just got my 4s yesterday after screwing up my 3 with the laterd version update. EVery call I have been on has either changed to speaker, called another number or ended the call or activated facetime, which I have turned off. never had this trouble with my 3...I don't even want to talk to anyone on this phone! Is the sensor bad? That is what the AT&t rep suggested.

Restore as new... if the problem still continues then there is a hardware issue.
If it stops after a restore as new, then the issue is with the backup the device is currently setup with.

Question about the new Yoga 10 HD+

Hi
A few questions about the new Yoga 10 HD+ which I hope you can answer.
I bought the old model last year. Loved the design and long battery time but a few major issues made me return it.
Somewhere I read that it can't read NTFS over USB so I presume that's the same with an NTFS formatted microSD card?
Can it read exFAT formatted microSD cards?
Anyone observed issues regarding audio over bluetooth?
(I know BT isn't exactly High End HiFi but the old Yoga 10 for some odd reason - most likely a driver issue which nobody cared to fix - sounded *much* worse with quite noticeably distortion while both my phone and a cheap noname tablet I have zero fidelity issues - no matter which of my bluetooth audio devices I tried aptX or not)
So to avoid buying this only to return it too I really would like to see if I can have my questions answered before buying it.
While I love the form factor and long running time the above issues are just two mayor dealbreakers to me. Bad audio quality = no joy listening to spotify, local MP3s etc. No NTFS or exFAT = no large movies.
My old noname android tablet really could use an upgrade so I'm really curious whether this can be it or I should look at the competition and sacrify form factor and battery runtime.
Thanks in advance.
EDIT:
If it's not supporting either NTFS or exFAT on the microSD have anyone tried ext3 and/or ext4?
I mean with Androids Linux roots it should be a nobrainer to support at least when it comes to royalties unlike NTFS or exFAT where there *might* be some issues with Microsoft.
Solved!
Go to Solution.

Thanks!
OK. Seems I should just stay clear of this and look elsewhere
Sony for sure I know support exFAT. I'm usure about Samsung. Odd it seems so hard to find out. File sizes of +4 GB should be taken for granted - it's not 199x anymore...
Oh well. Wonder whether to just go for one from the competition or perhaps just save the money and wait until 64 bit catches on. Rumors is that the next Nexus 8 will be 64 bit... (I really don't expect an answer on this)

I got an answer and I replied with a question about the answer, does no show in unanswered

I got an answer and I replied with a question about the answer, does no show in unanswered questions. I guess replying was not the way to get another anwer, How do I do that?
He said - Certain Firefox problems can be solved by performing a Clean reinstall. This means you remove Firefox program files and then reinstall Firefox.
I want to know - Will I still have my bookmarks, history, addons, plugins, etc.? I do not know what plugins and such that I had. What about my pinned tabs and my tabs that where open.
More information - When I try to start Firefox I keep getting the message that I need to restart my computer in order to complete a previous update attempt. I had Sweetpacks on my PC and I do not know where it came from, it took over my home page in Internet Explorer and Ithink caused the issue with Firefox.
Should I do the clean install or try starting Firefox now.

Could you please stay in the thread where you posted the question and reply there instead of opening a new thread?
Locking this thread, so please continue here:
*[[/questions/968194]]
See also:
*[[/questions/968222]]
You won't lose bookmarks and other data in the Firefox profile folder as long as you do not remove personal data in case you uninstall Firefox.
See also:
*http://kb.mozillazine.org/Profile_backup
*https://support.mozilla.org/kb/Backing+up+your+information
You can open the Properties of the Firefox desktop shortcut via the right-click context menu and check the "Compatibility" tab.<br />
Make sure that all items are deselected in the "Compatibility" tab of the Properties window.

Question about the animated Pen tool

Hi,
ive a question about the animated pen-tool.
i draw a word, but my hand isnt very calm, so the result is what you see on the screenshot.
Is there a possibility to reduce the points on the animated pen tool like in illustrator?
i know in illustrator its possible, but i didnt found anything in after effects to do it.
thanks for your help

If you are using the Paint tools those options don't exist in After Effects. The only work around is to set a keyframe for the brush path, copy the keyframe, then go to Illustrator and in a blank document the same size as your layer paste. Once in Illustrator you can simplify the path, select it, copy it, then go back to After Effects and select the same keyframe then paste. If you get a mask instead of a new path delete the mask path, make sure you have only the original brush path keyframe selected, then go to Edit>Paste from the menu.
It doesn't look like you're drawing a mask path. That might be a better way to go.

I see lots of people asking questions about the "white screen" app store update failure. I see no answers from Apple about this...What is the problem, and what is the solution?

I see lots of people asking questions about the "white screen" app store update failure. I see no answers from Apple about this...What is the problem, and what is the solution?

It's a problem that Apple is having with their App updating system. The best solution is to be patient, and wait for Apple to solve their systemic problem.

Questions about the T410s

Hey guys,
I'm considering buying the T410s because my last laptop was a Dell XPS and the GPU burned down after two years. I am a college student and I use my laptops quite extensively for homework, flash games, TV and movies. And I have a couple of questions about the T410s.
1. Due to my previous experience with my Dell XPS, I am looking for a more reliable laptop. So would I have to worry about the T410s heating up/burning down or breaking in like two years?
2. I am not much of a gamer, but enjoy videos sometimes. Will the Intel graphics card be able to run 'not so intense' games like Starcraft 2?
3. Also, would the 4gig of RAM be sufficient to run the Windows 7 64bit smoothly or I should choose the 32bit instead?
Thanks!!
Solved!
Go to Solution.

1) your Dell XPS used the Nvidia GPU? That won't happen in the new T410s.
2) the Intel 5700 MHD GPU can handle 1080p easily, but games like Starcraft 2 may only played on low to med settings.
the Nvidia GPU Optimus GPU option would allow 4 LCD support through the dock, if you ever want to connect that many LCD in the future.
3) 4 gigs is fine for 64 bit OS.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

A question about the XS key

Hi,
I have a quick question about the XS key used for Logic. Now, the XS key is a small piece of hardware and it is very susceptible to being misplaced or lost.
If someone were to lose the XS key, how would one be able to obtain another XS Key? Would that person need to buy Logic all over again? Or can they make a special order to get another one based on proof of ownership of Logic?
it's just a small question.
thanks
-Justin

There have been threads about this recently if you search for them.
I think someone said they got theirs replaced for about $80.

A question about the example "Filter"

Hi,
I have a question about the example "Filter (The Filter example illustrates how to filter data using a butterworth filter)" in the measurement studio reference now, it is one of the analysis examples.
I load this example in Vc++, but when I compile it, the error messages are:
"'ButterworthHighPass' : is not a member of 'CNiMath'" ,
"'ButterworthHighPass' : undeclared identifier",
"'ButterworthLowPass' : is not a member of 'CNiMath'" ,
"'ButterworthLowPass' : undeclared identifier",
"'WhiteNoiseWave' : is not a member of 'CNiMath'" ,
"'WhiteNoiseWave' : undeclared identifier",
Can you tell me what is matter? and how can I solve it?
Thanks!

Hi,
I was hoping that you could tell me what version and edition you have of Measurement Studio. I also need to know if you are using .NET or 6.0. For example, "I am using Mesurement Studio Enterprise edition 7.1 for Visual Studio .NET."
Depending on the version that you have, different functions and controls are included. I believe that you may have an edition that does not include the Butterworth filter. Let me know and we can go from there.
Thanks,
Caroline
National Instruments
Thanks,
Caroline Tipton
Data Management Product Manager
National Instruments

Re: Question about the Satellite P300-18Z

Hello everyone,
I have a couple of questions about the Satellite P300-18Z.
What "video out" does this laptop have? (DVI, s-video or d-sub)
Can I link the laptop up to a LCD-TV and watch movies on a resolution of 1080p? (full-HD)
What is the warranty on this laptop?

Hello
According the notebook specification Satellite P300-18Z has follow interfaces:
DVI - No DVI port available
HDMI - HDMI-out (HDMI out port available)
Headphone Jack - External Headphone Jack (Stereo) available
.link - iLink (Firewire) port available
Line in Jack - No Line in Jack port available
Line out Jack - No Line Out Jack available
Microphone Jack - External Micrphone Jack
TV-out - port available (S-Video port)
VGA - VGA (External monitor port RGB port)
Also you can connect it to your LCD TV using HDMI cable.
Warranty is country specific and clarifies this with your local dealer but I know that all Toshiba products have 1 year standard warranty and also 1 year international warranty. you can of course expand it.

A question about the impact of SQL*PLUS SERVEROUTPUT option on v$sql

Hello everybody,
SQL> SELECT * FROM v$version;
BANNER
Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
PL/SQL Release 11.2.0.1.0 - Production
CORE    11.2.0.1.0 Production
TNS for Linux: Version 11.2.0.1.0 - Production
NLSRTL Version 11.2.0.1.0 - Production
SQL>
OS : Fedora Core 17 (X86_64) Kernel 3.6.6-1.fc17.x86_64I would like to ask a question about the SQL*Plus SET SERVEROUTPUT ON/OFF option and its impact on queries on views such as v$sql and v$session. Here is the problem
Actually I define three variables in SQL*Plus in order to store sid, serial# and prev_sql_id columns from v$session in order to be able to use them later, several times in different other queries, while I'm still working in the current session.
So, here is how I proceed
SET SERVEROUTPUT ON; -- I often activate this option as the first line of almost all of my SQL-PL/SQL script files
SET SQLBLANKLINES ON;
VARIABLE mysid NUMBER
VARIABLE myserial# NUMBER;
VARIABLE saved_sql_id VARCHAR2(13);
-- So first I store sid and serial# for the current session
BEGIN
    SELECT sid, serial# INTO :mysid, :myserial#
    FROM v$session
    WHERE audsid = SYS_CONTEXT('UserEnv', 'SessionId');
END;
PL/SQL procedure successfully completed.
-- Just check to see the result
SQL> SELECT :mysid, :myserial# FROM DUAL;
    :MYSID :MYSERIAL#
       129   1067
SQL> Now, let's say that I want to run the following query as the last SQL statement run within my current session
SELECT * FROM employees WHERE salary >= 2800 AND ROWNUM <= 10;According to Oracle® Database Reference 11g Release 2 (11.2) description for v$session
http://docs.oracle.com/cd/E11882_01/server.112/e25513/dynviews_3016.htm#REFRN30223]
the column prev_sql_id includes the sql_id of the last sql statement executed for the given sid and serial# which in the case of my example, it will be the above mentioned SELECT query on the employees table. As a result, right after the SELECT statement on the employees table I run the following
BEGIN
    SELECT prev_sql_id INTO :saved_sql_id
    FROM v$session
    WHERE sid = :mysid AND serial# = :myserial#;
END;
PL/SQL procedure successfully completed.
SQL> SELECT :saved_sql_id FROM DUAL;
:SAVED_SQL_ID
9babjv8yq8ru3
SQL> Having the value of sql_id, I'm supposed to find all information about cursor(s) for my SELECT statement and also its sql_text value in v$sql. Yet here is what I get when I query v$sql upon the stored sql_id
SELECT child_number, sql_id, sql_text
FROM v$sql
WHERE sql_id = :saved_sql_id;
CHILD_NUMBER   SQL_ID          SQL_TEXT
0              9babjv8yq8ru3    BEGIN DBMS_OUTPUT.GET_LINES(:LINES, :NUMLINES); END;Therefore instead of
SELECT * FROM employees WHERE salary >= 2800 AND ROWNUM <= 10;for the value of sql_text I get the following value
BEGIN DBMS_OUTPUT.GET_LINES(:LINES, :NUMLINES);Which is not of course what I was expecting to find in v$sql for the given sql_id.
After a bit googling I found the following thread on the OTN forum where it had been suggested (well I think maybe not exactly for the same problem) to turn off SERVEROUTPUT.
Problem with dbms_xplan.display_cursor
This was precisely what I did
SET SERVEROUTPUT OFFafter that I repeated the whole procedure and this time everything worked pretty well as expected. I checked SQL*Plus documentation for SERVEROUTPUT
and also v$session page, yet I didn't find anything indicating that SERVEROUTPUT should be switched off whenever views such as v$sql, v$session
are queired. I don't really understand the link in terms of impact that one can have on the other or better to say rather, why there is an impact
Could anyone kindly make some clarification?
thanks in advance,
Regards,
Dariyoosh

>
and also v$session page, yet I didn't find anything indicating that SERVEROUTPUT should be switched off whenever views such as v$sql, v$session
are queired. I don't really understand the link in terms of impact that one can have on the other or better to say rather, why there is an impact
Hi Dariyoosh,
SET SERVEROUTPUT ON has the effect of executing dbms_output.get_lines after each and every statement. Not only related to system view.
Here below what Tom Kyte is explaining in this page:
Now, sqlplus sees this functionality and says "hey, would not it be nice for me to dump this buffer to screen for the user?". So, they added the SQLPlus command "set serveroutput on" which does two things
1) it tells SQLPLUS you would like it <b>to execute dbms_output.get_lines after each and every statement</b>. You would like it to do this network rounding after each call. You would like this extra overhead to take place (think of an install script with hundreds/thousands of statements to be executed -- perhaps, just perhaps you don't want this extra call after every call)
2) SQLPLUS automatically calls the dbms_output API "enable" to turn on the buffering that happens in the package.Regards.
Al

Questions about the Apple Developer Enterprise Program

Hi there,
i got some questions about the Apple Developer Enterprise Program:
- is there a way a company can create their own "AppStore" with only the APPs the employees should use?
- when I developed the enterprise app are the install files on a apple hosted server or do i need my own infrastructure to distribute my app?
Thanks in advance for answers!

Google: MDM

Some questions about the integration between BIEE and EBS

Hi, dear,
I'm a new bie of BIEE. In these days, have a look about BIEE architecture and the BIEE components. In the next project, there are some work about BIEE development based on EBS application. I have some questions about the integration :
1) generally, is the BIEE database and application server decentralized with EBS database and application? Both BIEE 10g and 11g version can be integrated with EBS R12?
2) In BIEE administrator tool, the first step is to create physical tables. if the source appliation is EBS, is it still needed to create the physical tables?
3) if the physical tables creation is needed, how to complete the data transfer from the EBS source tables to BIEE physical tables? which ETL tool is prefer for most developers? warehouse builder or Oracle Data Integration?
4) During data transfer phase, if there are many many large volume data needs to transfer, how to keep the completeness? for example, it needs to transfer 1 million rows from source database to BIEE physical tables, when 50%is completed, the users try to open the BIEE report, can they see the new 50% data on the reports? is there some transaction control in ETL phase?
could anyone give some guide for me? I'm very appreciated if you can also give any other information.
Thanks in advance.

1) generally, is the BIEE database and application server decentralized with EBS database and application? Both BIEE 10g and 11g version can be integrated with EBS R12?You, shud consider OBI Application here which uses OBIEE as a reporting tool with different pre-built modules. Both 10g & 11g comes with different versions of BI apps which supports sources like Siebel CRM, EBS, Peoplesoft, JD Edwards etc..
2) In BIEE administrator tool, the first step is to create physical tables. if the source appliation is EBS, is it still needed to create the physical tables?Its independent of any soure. This is OBIEE modeling to create RPD with all the layers. If you build it from scratch then you will require to create all the layers else if BI Apps is used then you will get pre-built RPD along with other pre-built components.
3) if the physical tables creation is needed, how to complete the data transfer from the EBS source tables to BIEE physical tables? which ETL tool is prefer for most developers? warehouse builder or Oracle Data Integration?BI apps comes with pre-built ETL mapping to use with the tools majorly with Informatica. Only BI Apps 7.9.5.2 comes with ODI but oracle has plans to have only ODI for any further releases.
4) During data transfer phase, if there are many many large volume data needs to transfer, how to keep the completeness? for example, it needs to transfer 1 million rows from source database to BIEE physical tables, when 50%is completed, the users try to open the BIEE report, can they see the new 50% data on the reports? is there some transaction control in ETL phase?User will still see old data because its good to turn on Cache and purge it after every load.
Refer..http://www.oracle.com/us/solutions/ent-performance-bi/bi-applications-066544.html
and many more docs on google
Hope this helps

[solved] Question about the Hardware Abstraction Layer (HAL)

Similar Messages

Maybe you are looking for