[Solved] Realtek RTL8188SU wireless USB - not listed in ifconfig

The built-in wireless adaptor (based on ath5k) of my Acer Aspire One is really flaky (disappears completely after anywhere between 30 seconds and an hour), so I decided to buy a USB wireless-N adaptor, to get some stability and take advantage of my wireless-N router. After plugging it in and booting, it wasn't listed. This was due to the custom kernel I use (kernel-netbook, from the AUR) not having it compiled. So I recompiled it, selecting all the Realtek entries as modules. I rebooted into the new kernel, but still it wasn't discovered. I've tried using modprobe to load the drivers in (one by one, as the RTL8188SU doesn't actually have a driver by it's name, so I tried all the Realtek ones, rebooting in between), but still no luck - it's still not appearing under ifconfig.
I'm pretty noob when it comes to troubleshooting, but I'm learning. Just need a few pointers
What do I have to do to get it to appear in ifconfig? Do I have to blacklist my ath5k (can't see why, it's possible to have more than one wireless adaptor, surely??)
Edit: http://www.realtek.com.tw/downloads/dow … =true#2282
If I understand this correctly, the driver isn't in the kernel and I need to download this??
Last edited by chemicalfan (2011-07-23 19:23:59)

Ok, just found out from the Debian wiki (http://wiki.debian.org/rtl819x), that the r8192s_usb driver was superseeded and removed from kernel 2.6.37 (whether this is Debian specific, I'm not sure) - I'm running 2.6.39, so it's not in my kernel. It's apparently been replaced by r8712u, which should be in the kernel, so I'm confused why I'm still having trouble? Would the command be "modprobe r8712u", or something different?
Edit: Ok, according to this - http://www.archlinux.org/packages/core/ … -firmware/ - the driver is included in this package, which I installed a couple of days ago. It's listed as "lib/firmware/rtlwifi/rtl8712u.bin", so.......how do I get it working?
Last edited by chemicalfan (2011-07-20 09:05:40)

Similar Messages

[Solved] Realtek RTL8188SU chip - unstable wifi

Hi All,
I have a wireless usb dongle using the above chip. lsusb says:
Belkin Components F7D1101 v1 Basic Wireless Adapter [Realtek RTL8188SU]
The wifi speed is very unstable (at the beginning of downloading each file, the speed is about 300KB/s, then goes down, down and down to 0). I'm sure that it's not because of my router. Does anybody know how to find where my problem is?
Thank you.
Edit: I would like to thank Xyne a lot. My wireless usb dongle doesn't mention about rtl8192 but he asked me to search for it in the forums and then I found this thread. The solution that works for me is changing the channel. I cannot express how I love the Arch community :-)
Last edited by dxxvi (2013-10-21 16:07:57)

Search for "rtl8192" on the forum (link at the top left). There are numerous threads concerning the consistently poor performance of Realtek wifi cards. You will find instructions for changing some of the power management options which may reduce the rate of dropped connections, but they will keep dropping and speed will remain inconsistent and embarrassingly slow.
You can check which kernel modules your card is using with
lsmod | grep rtl
If you see rtl8192ce in that list, curse your vendor and head out to buy a new dongle. Of course, if your card is using something other than rtl8192* then maybe tweaking the module options will actually lead to decent performance.

HP w1907v - Wireless Usb not connecting

HP w1907v - Could not use my computer because the wireless connect usb is not working. No blue light on the usb.

PecMed wrote:
HP w1907v - Could not use my computer because the wireless connect usb is not working. No blue light on the usb.
Hi,
Firstly the monior ONLY has VGA connection:
VGA 15-pin D-type connector
How do you connect it to your computer ? It does not have USB port how do you connect USB with blue light to the monitor ?
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

[mostly solved]RaLink RT2860 wireless NIC not working, in eeePC 1000HE

I'm having trouble getting my wireless NIC to work.
I have a clean, up-to-date system, no [testing]. I'm using the stock kernel, 2.6.30, which according to the 1000HE wiki (http://wiki.archlinux.org/index.php/Asu … 000HE#WiFi), is supposed to work out of the box.
The problem I run into with iwconfig is that it doesn't set an essid. The essid shows as blank, then I run:
iwconfig ra0 essid "my id"
and iwconfig ra0 again shows a blank essid.
I've tried wpa_supplicant, and it just spams CTRL-EVENT-SCAN-RESULTS indefinitely (my config file is attached).
I've tried wifi radar, and it gives me errors about the network I'm trying to connect to having no AP address.
I've only tried to connect to the one network here that I have access to. It's an unsecured university network with many APs (I think it's called roaming or something?). Once you have an IP leased, you try to go to a website and are automatically forwarded to an authentication login page.
I've attached the output from a bunch of different commands:
ifconfig -a:
eth0 Link encap:Ethernet HWaddr 00:26:18:40:58:85
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
ra0 Link encap:Ethernet HWaddr 00:25:D3:13:D2:4E
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:99 errors:0 dropped:0 overruns:0 frame:0
TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:13066 (12.7 Kb) TX bytes:0 (0.0 b)
Interrupt:19
iwconfig:
ra0 RT2860 Wireless ESSID:"" Nickname:"RT2860STA"
Mode:Auto Frequency=2.412 GHz Bit Rate=1 Mb/s
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=10/100 Signal level:0 dBm Noise level:-97 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
iwconfig ra0 essid "hi": returns no output
afterward, iwconfig returns identical output as above
iwlist ra0 scan:
ra0 Scan completed :
Cell 01 - Address: 00:0C:E6:40:7E:00
ESSID:"UM Wireless Network"
Mode:Managed
Channel:11
Quality:65/100 Signal level:-64 dBm Noise level:-97 dBm
Encryption key:off
Bit Rates:54 Mb/s
Cell 02 - Address: 00:0C:E6:40:7E:01
ESSID:"MWireless"
Mode:Managed
Channel:11
Quality:65/100 Signal level:-64 dBm Noise level:-97 dBm
Encryption key:on
Bit Rates:54 Mb/s
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
Cell 03 - Address: 00:0C:E6:40:76:00
ESSID:"UM Wireless Network"
Mode:Managed
Channel:11
Quality:24/100 Signal level:-80 dBm Noise level:-97 dBm
Encryption key:off
Bit Rates:54 Mb/s
Cell 04 - Address: 00:0C:E6:40:76:01
ESSID:"MWireless"
Mode:Managed
Channel:11
Quality:34/100 Signal level:-76 dBm Noise level:-97 dBm
Encryption key:on
Bit Rates:54 Mb/s
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
Cell 05 - Address: 00:0C:E6:40:88:00
ESSID:"UM Wireless Network"
Mode:Managed
Channel:11
Quality:60/100 Signal level:-66 dBm Noise level:-97 dBm
Encryption key:off
Bit Rates:54 Mb/s
Cell 06 - Address: 00:0C:E6:40:7B:00
ESSID:"UM Wireless Network"
Mode:Managed
Channel:11
Quality:20/100 Signal level:-82 dBm Noise level:-97 dBm
Encryption key:off
Bit Rates:54 Mb/s
Cell 07 - Address: 00:0C:E6:40:97:01
ESSID:"MWireless"
Mode:Managed
Channel:11
Quality:20/100 Signal level:-82 dBm Noise level:-97 dBm
Encryption key:on
Bit Rates:54 Mb/s
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
Cell 08 - Address: 00:0C:E6:40:75:00
ESSID:"UM Wireless Network"
Mode:Managed
Channel:11
Quality:39/100 Signal level:-74 dBm Noise level:-97 dBm
Encryption key:off
Bit Rates:54 Mb/s
Cell 09 - Address: 00:0C:E6:40:88:01
ESSID:"MWireless"
Mode:Managed
Channel:11
Quality:65/100 Signal level:-64 dBm Noise level:-97 dBm
Encryption key:on
Bit Rates:54 Mb/s
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
Cell 10 - Address: 00:0C:E6:40:7B:01
ESSID:"MWireless"
Mode:Managed
Channel:11
Quality:20/100 Signal level:-82 dBm Noise level:-97 dBm
Encryption key:on
Bit Rates:54 Mb/s
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
Cell 11 - Address: 00:0C:E6:40:75:01
ESSID:"MWireless"
Mode:Managed
Channel:11
Quality:44/100 Signal level:-72 dBm Noise level:-97 dBm
Encryption key:on
Bit Rates:54 Mb/s
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
Cell 12 - Address: 00:0C:E6:40:8D:00
ESSID:"UM Wireless Network"
Mode:Managed
Channel:11
Quality:20/100 Signal level:-82 dBm Noise level:-97 dBm
Encryption key:off
Bit Rates:54 Mb/s
Cell 13 - Address: 00:0C:E6:40:8D:01
ESSID:"MWireless"
Mode:Managed
Channel:11
Quality:20/100 Signal level:-82 dBm Noise level:-97 dBm
Encryption key:on
Bit Rates:54 Mb/s
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
iwpriv:
ra0 Available private ioctls :
set (8BE2) : set 1024 char & get 0
connStatus (0004) : set 0 & get 2047 char
driverVer (0005) : set 0 & get 2047 char
bainfo (0006) : set 0 & get 2047 char
descinfo (0007) : set 0 & get 2047 char
radio_off (000A) : set 0 & get 2047 char
radio_on (000B) : set 0 & get 2047 char
show (0014) : set 1024 char & get 2047 char
bbp (8BE3) : set 2047 char & get 2047 char
mac (8BE5) : set 1024 char & get 1024 char
e2p (8BE7) : set 1024 char & get 1024 char
stat (8BE9) : set 0 & get 2047 char
get_site_survey (8BED) : set 0 & get 1024 char
lspci:
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02)
01:00.0 Network controller: RaLink RT2860
03:00.0 Ethernet controller: Attansic Technology Corp. L1e Gigabit Ethernet Adapter (rev b0)
wpa_supplicant -Dwext -ira0 -c/etc/wpa_supplicant.conf:
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-TERMINATING - signal 2 received
cat /etc/wpa_supplicant.conf:
# Catch all example that allows more or less all configuration modes
network={
ssid="UM Wireless Network"
scan_ssid=1
key_mgmt=WPA-EAP WPA-PSK IEEE8021X NONE
pairwise=CCMP TKIP
group=CCMP TKIP WEP104 WEP40
psk="very secret passphrase"
eap=TTLS PEAP TLS
identity="[email protected]"
password="foobar"
ca_cert="/etc/cert/ca.pem"
client_cert="/etc/cert/user.pem"
private_key="/etc/cert/user.prv"
private_key_passwd="password"
phase1="peaplabel=0"
dmesg: (This was run after all the other commands. I ran the wpa_supplicant command a couple of times, so the tail of the output is the result of a few different attempts by wpa_supplicant to find a network.)
Linux version 2.6.30-ARCH (root@arch) (gcc version 4.4.0 20090630 (prerelease) (GCC) ) #1 SMP PREEMPT Sat Jul 4 11:13:08 UTC 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f7a0000 (usable)
BIOS-e820: 000000007f7a0000 - 000000007f7ae000 (ACPI data)
BIOS-e820: 000000007f7ae000 - 000000007f7f0000 (ACPI NVS)
BIOS-e820: 000000007f7f0000 - 000000007f800000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7f7a0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask 080000000 write-back
1 base 07F800000 mask 0FF800000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e2000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000007f7a0000 (usable)
modified: 000000007f7a0000 - 000000007f7ae000 (ACPI data)
modified: 000000007f7ae000 - 000000007f7f0000 (ACPI NVS)
modified: 000000007f7f0000 - 000000007f800000 (reserved)
modified: 00000000fee00000 - 00000000fee01000 (reserved)
modified: 00000000fff80000 - 0000000100000000 (reserved)
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 7f6fc000 - 7f78fe11
Allocated new RAMDISK: 00628000 - 006bbe11
Move RAMDISK from 000000007f6fc000 - 000000007f78fe10 to 00628000 - 006bbe10
ACPI: RSDP 000fb9d0 00014 (v00 ACPIAM)
ACPI: RSDT 7f7a0000 0003C (v01 A_M_I_ OEMRSDT 04000920 MSFT 00000097)
ACPI: FACP 7f7a0200 00084 (v02 A_M_I_ OEMFACP 04000920 MSFT 00000097)
ACPI: DSDT 7f7a0430 05D8C (v01 A1192 A1192000 00000000 INTL 20051117)
ACPI: FACS 7f7ae000 00040
ACPI: APIC 7f7a0390 0005C (v01 A_M_I_ OEMAPIC 04000920 MSFT 00000097)
ACPI: MCFG 7f7a03f0 0003C (v01 A_M_I_ OEMMCFG 04000920 MSFT 00000097)
ACPI: OEMB 7f7ae040 00061 (v01 A_M_I_ AMI_OEM 04000920 MSFT 00000097)
ACPI: HPET 7f7a61c0 00038 (v01 A_M_I_ OEMHPET 04000920 MSFT 00000097)
ACPI: SSDT 7f7aeb40 004F0 (v01 PmRef CpuPm 00003000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
1151MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 0000624e44] TEXT DATA BSS ==> [0000100000 - 0000624e44]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [0000625000 - 00006271e0] BRK ==> [0000625000 - 00006271e0]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [0000628000 - 00006bbe11] NEW RAMDISK ==> [0000628000 - 00006bbe11]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00ff780] ff780
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007f7a0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0007f7a0
On node 0 totalpages: 522031
free_area_init_node: node 0, pgdat c04c1380, node_mem_map c1000200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2304 pages used for memmap
HighMem zone: 292514 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0xffffffff base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e2000
PM: Registered nosave memory: 00000000000e2000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 7f800000:7f600000)
NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 11 pages at c1ffa000, static data 24444 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517951
Kernel command line: root=/dev/disk/by-uuid/2debd498-3ab0-459c-afbe-d75860e0d650 ro
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
NR_IRQS:512
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 1662.281 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Initializing HighMem for node 0 (000377fe:0007f7a0)
Memory: 2064176k/2088576k available (2902k kernel code, 23140k reserved, 1047k data, 392k init, 1179272k highmem)
virtual kernel memory layout:
fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc04e1000 - 0xc0543000 ( 392 kB)
.data : 0xc03d590f - 0xc04db6a8 (1047 kB)
.text : 0xc0100000 - 0xc03d590f (2902 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 3325.08 BogoMIPS (lpj=5540936)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090320
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Atom(TM) CPU N280 @ 1.66GHz stepping 02
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3326.54 BogoMIPS (lpj=5541676)
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Atom(TM) CPU N280 @ 1.66GHz stepping 02
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (6652.63 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level SIBLING
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level SIBLING
groups: 1 0
net_namespace: 1056 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:02.0: reg 10 32bit mmio: [0xf7f00000-0xf7f7ffff]
pci 0000:00:02.0: reg 14 io port: [0xdc00-0xdc07]
pci 0000:00:02.0: reg 18 32bit mmio: [0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 1c 32bit mmio: [0xf7ec0000-0xf7efffff]
pci 0000:00:02.1: reg 10 32bit mmio: [0xf7f80000-0xf7ffffff]
pci 0000:00:1b.0: reg 10 64bit mmio: [0xf7eb8000-0xf7ebbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xd400-0xd41f]
pci 0000:00:1d.1: reg 20 io port: [0xd480-0xd49f]
pci 0000:00:1d.2: reg 20 io port: [0xd800-0xd81f]
pci 0000:00:1d.3: reg 20 io port: [0xd880-0xd89f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xf7eb7c00-0xf7eb7fff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0380 (mask 0003)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 0007)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0068 (mask 0003)
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x8f0-0x8f7]
pci 0000:00:1f.1: reg 1c io port: [0x8f8-0x8fb]
pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:1f.2: reg 10 io port: [0xd080-0xd087]
pci 0000:00:1f.2: reg 14 io port: [0xd000-0xd003]
pci 0000:00:1f.2: reg 18 io port: [0xcc00-0xcc07]
pci 0000:00:1f.2: reg 1c io port: [0xc880-0xc883]
pci 0000:00:1f.2: reg 20 io port: [0xc800-0xc80f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xf7eb7800-0xf7eb7bff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:03:00.0: reg 10 64bit mmio: [0xfbfc0000-0xfbffffff]
pci 0000:03:00.0: reg 18 io port: [0xec00-0xec7f]
pci 0000:03:00.0: PME# supported from D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.1: bridge io port: [0xe000-0xefff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xfbf00000-0xfbffffff]
pci 0000:01:00.0: reg 10 32bit mmio: [0xfbef0000-0xfbefffff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:00:1c.3: bridge 32bit mmio: [0xf8000000-0xfbefffff]
pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf0000000-0xf6ffffff]
pci 0000:00:1e.0: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
system 00:08: ioport range 0x25c-0x25f has been reserved
system 00:08: ioport range 0x380-0x383 has been reserved
system 00:08: ioport range 0x400-0x41f has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x87f has been reserved
system 00:08: ioport range 0x480-0x4bf has been reserved
system 00:08: iomem range 0x8c000000-0x8c01ffff has been reserved
system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0b: iomem range 0xe0000000-0xe3ffffff has been reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
system 00:0c: iomem range 0x100000-0x7f7fffff could not be reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.0: IO window: disabled
pci 0000:00:1c.0: MEM window: disabled
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1: IO window: 0xe000-0xefff
pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff
pci 0000:00:1c.1: PREFETCH window: disabled
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:01
pci 0000:00:1c.3: IO window: disabled
pci 0000:00:1c.3: MEM window: 0xf8000000-0xfbefffff
pci 0000:00:1c.3: PREFETCH window: 0x000000f0000000-0x000000f6ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: disabled
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:03: resource 0 io: [0xe000-0xefff]
pci_bus 0000:03: resource 1 mem: [0xfbf00000-0xfbffffff]
pci_bus 0000:01: resource 1 mem: [0xf8000000-0xfbefffff]
pci_bus 0000:01: resource 2 pref mem [0xf0000000-0xf6ffffff]
pci_bus 0000:05: resource 3 io: [0x00-0xffff]
pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...
Freeing initrd memory: 591k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1247582678.410:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1731
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.3: irq 26 for MSI/MSI-X
pcieport-driver 0000:00:1c.3: setting latency timer to 64
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 392k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 27 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xf7eb7800 port 0xf7eb7900 irq 27
ata2: DUMMY
ata3: SATA max UDMA/133 abar m1024@0xf7eb7800 port 0xf7eb7a00 irq 27
ata4: DUMMY
pata_acpi 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pata_acpi 0000:00:1f.1: setting latency timer to 64
pata_acpi 0000:00:1f.1: PCI INT A disabled
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata1.00: ATA-8: Hitachi HTS543216L9SA00, FB2OC40C, max UDMA/133
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54321 FB2O PQ: 0 ANSI: 5
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi4 : ata_piix
scsi5 : ata_piix
ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
ata6: port disabled. ignoring.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
udev: starting version 141
ACPI: AC Adapter [AC0] (on-line)
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
ACPI: Power Button [PWRB]
ACPI: SSDT 7f7ae180 001FA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 7f7ae410 00724 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [P001] (supports 8 throttling states)
ACPI: SSDT 7f7ae0b0 000CC (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
ACPI: SSDT 7f7ae380 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
ACPI: CPU1 (power states: C1[C1] C2[C2])
processor ACPI_CPU:01: registered as cooling_device1
ACPI: Processor [P002] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [TZ00] (42 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
Linux agpgart interface v0.103
intel_rng: FWH not detected
usbcore: registered new device driver usb
input: PC Speaker as /devices/platform/pcspkr/input/input6
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:19/input/input7
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
rt2860sta: module is from the staging directory, the quality is unknown, you have been warned.
rt2860 0000:01:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
=== pAd = f8591000, size = 580808 ===
<-- RTMPAllocAdapterBlock, Status=0
rt2860 0000:01:00.0: setting latency timer to 64
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ATL1E 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
ATL1E 0000:03:00.0: setting latency timer to 64
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d480
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d880
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
agpgart-intel 0000:00:00.0: Intel 945GME Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
iTCO_vendor_support: vendor-support=0
eeepc: Eee PC Hotkey Driver
eeepc: Hotkey init flags 0x41
eeepc: Get control methods supported: 0x101713
input: Asus EeePC extra buttons as /devices/virtual/input/input8
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
usb 1-8: new high speed USB device using ehci_hcd and address 3
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
HDA Intel 0000:00:1b.0: setting latency timer to 64
psmouse serio1: ID: 10 00 64
usb 1-8: configuration #1 chosen from 1 choice
elantech.c: assuming hardware version 2, firmware version 2.48
usb 5-1: new full speed USB device using uhci_hcd and address 2
elantech.c: Synaptics capabilities query result 0x00, 0x02, 0x64.
usb 5-1: configuration #1 chosen from 1 choice
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
Linux video capture interface: v2.00
input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input10
uvcvideo: Found UVC 1.00 device CNF7129 (04f2:b071)
input: CNF7129 as /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8:1.0/input/input11
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
EXT3 FS on sda3, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
Adding 1052248k swap on /dev/sda2. Priority:-1 extents:1 across:1052248k
RX DESC f649f000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
--> Error 2 opening /etc/Wireless/RT2860STA/RT2860STA.dat
1. Phy Mode = 0
2. Phy Mode = 0
3. Phy Mode = 0
RTMPSetPhyMode: channel is out of range, use first channel=1
MCS Set = 00 00 00 00 00
<==== RTMPInitialize, Status=0
0x1300 = 00073200
===>rt_ioctl_giwscan. 13(13) BSS returned, data->length = 1336
===>rt_ioctl_giwscan. 13(13) BSS returned, data->length = 1375
===>rt_ioctl_giwscan. 16(16) BSS returned, data->length = 1641
===>rt_ioctl_giwscan. 14(14) BSS returned, data->length = 1470
===>rt_ioctl_giwscan. 16(16) BSS returned, data->length = 1641
===>rt_ioctl_giwscan. 16(16) BSS returned, data->length = 1641
RX DESC f649f000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
--> Error 2 opening /etc/Wireless/RT2860STA/RT2860STA.dat
1. Phy Mode = 0
2. Phy Mode = 0
3. Phy Mode = 0
MCS Set = 00 00 00 00 00
<==== RTMPInitialize, Status=0
0x1300 = 00073200
RX DESC f73ce000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
--> Error 2 opening /etc/Wireless/RT2860STA/RT2860STA.dat
1. Phy Mode = 0
2. Phy Mode = 0
3. Phy Mode = 0
MCS Set = 00 00 00 00 00
<==== RTMPInitialize, Status=0
0x1300 = 00073200
===>rt_ioctl_giwscan. 14(14) BSS returned, data->length = 1431
===>rt_ioctl_giwscan. 12(12) BSS returned, data->length = 1240
===>rt_ioctl_giwscan. 15(15) BSS returned, data->length = 1619
===>rt_ioctl_giwscan. 15(15) BSS returned, data->length = 1619
===>rt_ioctl_giwscan. 15(15) BSS returned, data->length = 1588
===>rt_ioctl_giwscan. 15(15) BSS returned, data->length = 1619
===>rt_ioctl_giwscan. 16(16) BSS returned, data->length = 1714
===>rt_ioctl_giwscan. 17(17) BSS returned, data->length = 1779
===>rt_ioctl_giwscan. 13(13) BSS returned, data->length = 1409
===>rt_ioctl_giwscan. 12(12) BSS returned, data->length = 1240
RX DESC f6948000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
--> Error 2 opening /etc/Wireless/RT2860STA/RT2860STA.dat
1. Phy Mode = 0
2. Phy Mode = 0
3. Phy Mode = 0
MCS Set = 00 00 00 00 00
<==== RTMPInitialize, Status=0
0x1300 = 00073200
===>rt_ioctl_giwscan. 12(12) BSS returned, data->length = 1240
===>rt_ioctl_giwscan. 10(10) BSS returned, data->length = 1070
===>rt_ioctl_giwscan. 13(13) BSS returned, data->length = 1355
===>rt_ioctl_giwscan. 15(15) BSS returned, data->length = 1546
===>rt_ioctl_giwscan. 13(13) BSS returned, data->length = 1316
===>rt_ioctl_giwscan. 13(13) BSS returned, data->length = 1355
===>rt_ioctl_giwscan. 14(14) BSS returned, data->length = 1470
===>rt_ioctl_giwscan. 14(14) BSS returned, data->length = 1470
===>rt_ioctl_giwscan. 11(11) BSS returned, data->length = 1165
===>rt_ioctl_giwscan. 11(11) BSS returned, data->length = 1145
===>rt_ioctl_giwscan. 14(14) BSS returned, data->length = 1504
===>rt_ioctl_giwscan. 15(15) BSS returned, data->length = 1546
Last edited by mishchea (2009-07-15 02:42:39)

Malstrond wrote:Mostly because Ralink just hacks their drivers together to work somehow. A module should never require files in /etc/, but they don't care. The file contains settings, ranging from packet thresholds to country selection. There is a readme file in the archive, you can change some interesting things in there, i.e. auto roaming.
The staging drivers included in the kernel have this settings file included in the module, but there have been problems with this in 2.6.30, among others, the included drivers for RT2870-based hardware, for example, can render your system unusable.
Sadly, there doesn't seem to be much effort on the side of Linux community either. Maybe it's because all the devs interested in this already bought one of earlier EEEs with an Atheros chipset.
I've got one of these cards and it works fine. I'm running 2.6.31.
I use a wpa_supplicant based connection. I suggest that you do the same, the config file is crap and it doesn't appear to accept iwconfig input.
For netcfg and this card, try netcfg 2.5 which will be out in the next 24 hours. In the meantime, you could configure your networks in a wpa_supplicant config file. Don't use a catch all like above, create a more specific one.

Can I order a scan from PSE12 directly and open it? On other versions of Photoshop I could scan from "import", and my type of scanner was listed. All I had to do was check the proper scanner. This scanner is wireless and not listed. The only thing that is

On other previous editions of Photoshop I could order the scanner to scan using "file", then "Import" on other versions, my scanner was listed. The scanner I have now is a wireless, does that make any difference. As I see it must be linked in some way. How do I do that? I am using PSE12.

Have you installed the TWAIN driver?
TWAIN not installed | Photoshop Elements 9 and later

[SOLVED (mysteriously)] Arch on USB not recognized during boot

Hi there,
I hope, someone can help me with my problem, I have been searching and trying different things for quite some time now, without success.
I treated myself a new Notebook, Acer Aspire S7 and wanted to run Arch on it. However I am new to Linux and want to try it out on an USB-Stick, to keep the factory install of Win8 intact. (Also, this notebook does not have such a great HDD capacity) Additionally I want to have full disk encryption.
So I followed the Beginner's Guide with modifications described here and here
When it came to install the bootloader I chose Grub for EFI.
I then removed the USB-Stick with the live-Arch, which I used for installation and rebooted and it worked!
However: As soon as I completely shut down and boot again, the USB-Stick with my installation is no longer recognized. If i boot the live-Arch again, reinstall Grub and then reboot, it again works.
Here is something, I found strange. This is the output of efibootmgr:
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 2001,0003,0002,2002,2003
Boot0000* USB HDD: KingstonDataTraveler 2.0
Boot0001* Intel HDD0
Boot0002* Windows Boot Manager
Boot0003* arch_grub
Boot2001* EFI USB Device
Boot2002* EFI DVD/CDROM
Boot2003* EFI Network
BootCurrent is 0000, but that number does not appear in the Boot-Order list. Could that be something?
Well, I hope someone has an idea. I will happily share any information about my setup with you, just ask.
Thanks,
Max
Last edited by MaxT (2014-04-07 08:35:20)

Sorry for digging that threat up again. I just wanted to share with you the solution to the problem I was having. Perhaps it will save someone else some frustration.
The Acer Aspire S7 has a dongle that goes in the display port and provides an ethernet and an VGA port. It was that dongle that prevented the USB stick with the Arch installation from being recognized. Done attached -> USB stick was ignored, dongle detached -> it worked.
I have no idea, why that is the case, but maybe this info is helpful for someone.
Cheers,
Max

Hp mini will not boot from usb and USB not listed as a choice

I have an HP mini 110-1116NR and it crashed. During a system restore it stopped working so now there is no operating system on it.
In BIOS there is no choice to boot from USB (when my disks come in mail from HP)
Also when it kinda starts im at the DOS screen....system32.exe???????
I dont know what this means

Hi cathy69:
Thank you for your inquiry. I am pleased to assist you!
I hope you had a great weekend!
I see you are looking to change the boot order on your computer. Here is a link to 'Configuring the Boot Order in the System Bios" click here. Please let me know if you require further assistance.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

[solved]installed chromium-no icon, not listed in menu

I installed chromium and it works great. But it isn't listed in "applications>internet", in KDE. I can get to it through the search bar, and if I had an icon for it I'd set it on my desktop. Any way to make that happen?
Last edited by pottzie (2010-06-15 19:27:41)

Yes indeed there is, and it's now on my desk top. Thank you very much.

After updating to iTunes 12 the Apple Mobile Device USB Driver is not listed, I use Windows 8.1, how can i solve this?

After I updates ITunes to the latest version (12), ITunes wont find my iphone and Ipad anymore, after searching I found that the Apple Mobile Device USB Driver is not listed anymore, on the support website of Apple it doesnt explain how to solve this,.
I use Windows 8.1 and so now also ITunes 12, both my Iphone 4S and Ipad Air have the latest IOS version.
I hope anybody can tell me how to solve this that the Apple Mobile Device USB Driver is back, thank you

Found a possible solution for me.
While the phone was plugged into my computer and iTunes is CLOSED.
1. I went to Services in Windows.
2. I selected Apple Mobile Device and right clicked and selected "Stop".
3. Then I right-clicked again and selected "Start".
4. Then I went to Device Manager and right clicked my iPhone with the yellow alert icon and selected "Uninstall". You will get a warning about uninstalling the device. Click OK.
5. At the top of Device Manager I clicked the Action menu and selected "Scan for Hardware Changes".
This re-installed the iPhone and everything started working again.

Sierra Wireless USB card will not connect

I have purchased a Sierra Wireless USB card (AT&T USB Connect 881) to use with a iBook G4. The green power lites are solid green. However, I can not get a signal from AT&T. No one has been able to help solve this problem. I am ready to return it to AT&T for a refund.

Thx for ur reply. I just checked the model of the USB adapter is Belkin Basic N150.
The xp is able to see and identify the iphone wireless network and shows it in available networks with full signal strength. Once I click on connect then an alert message says that it is detecting network type pls wait. Then another message appears stating that "selected network may be no longer in range. Pls refresh the list and connect again"
As suggested by you I will try it on windows 7.

Photosmart 7515 connect via USB but not wireless, Device not found on Network

Purchased a 7515 all-in-one, was able to setup wirelessly to MacPro but has lost ability to connect wirelessly. This happened with OS X Lion and nor MountainLion. Have a TimeMachine Airport. Printer connects to network but during setup from MacPro, repeatedly get "Device Not Found on Network" after stepping through wireless installation setup screens. I have reset router, printer, firmware updates, software updates.... at wits end. I have followed the instructions on the below resource page link with no luck. Use WPA-PSK encryption (Automatic AES or TKIP) on network and diagnostics on printer pass.
Please help anyone!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02946597&tmp_task=solveCategory&cc=us&dlc=en&la...

It sounds like the Macs and the printer just aren't communicating.
If you press the network icon on the printer, does it indicate it is connected to the network?
I recommend two additional steps that are not listed in the linked document. The printing system of the Mac may need to be reset as it will clear any software that could be interfering (such as corrupted installations).
Follow the steps as outlined for 10.7 or 10.8 in this document from HP.
The next step is to install the driver package from Apple. This can be found here.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Our HP 1150us g7 has stopped recognizing our dual USB 2.0 Port. It is not listed to uninstall and

Our HP 1150us g7 has stopped recognizing our dual USB 2.0 Port. It is not listed to uninstall or update its' drivers. Only the one USB port works on the right side facing the notebook.
It is only 21 days out of warranty and I am told they can be replaced however it takes a huge amount of labor, then someone else told us it can not be exchanged only the entire Motherboard. I have found the exact part on sale so I believe it is replaceable.
Here is a link to order the part we believe can be replaced.
http://www.machinaelectronics.com/store/buypart.cfm?pn=NL028516
Does anyone know if it is replaceable or not?
We are sick about this we only had the notebook one year and for the warranty to run out only 21 days before this died we are disappointed with HP for not providing some assistance.
This question was solved.
View Solution.

The link you provided is not the same model as yours. While it may work, I haven't verified it.
Have you performed any hardware troubleshooting on the unit yet?

Why Lion does not recodnise novatel wireless usb ovation mc990d

I did install novatel wireless usb adapter as per instructions, The system says "Your software installed succesfully", But when i open "network" i preferences, the novatel wireless modem is not there, as discribed in instructions. What to do?! Please HELP
Wesley

SthrnDixieCowgirl wrote:
I don't know how to remove and add printers unless I had to format my hard drive for a completely different reason and reinstalled the printer that way.
To remove the printer, open System Preferences > Print & Scan. You will see the HP in the Printers list. Click on it once to select it and then press the minus button under the Printers list to remove it.
With this done, click the plus button under the Printers list to add the printer. With the Add Printer window open and the Default view selected, the HP should appear in this view. Select it and the Print Using menu should change to the supporting printer driver. When this happens, click the Add button to complete the creation of the printer queue.
SthrnDixieCowgirl wrote:
I have heard other people have issues with 10.7.3 for other reasons and I should have waited until 10.7.4 came out before updating and I didn't and now there is nothing I can do to go back to 10.7.2
You cannot believe everything you read. For every person that had a problem after installing the .3 update, a hundred more had no problem.
But if you wanted to go back to 10.7.2, then you can use Time Machine to do this. If you are not using Time Machine then you need to start doing so. At least the update only stopped you from network printing. What if it had stopped you from using the Mac?

My phone is not listed on the itunes device sidebar when I plug in with the usb cord ... cant figure out why.... did just update macbook pro to snow leopard though?

My iphone is not listed as a device in the itunes side bar after i plug in to usb port? It used to show up fine - only change I think is that I upgraded macbook pro to snow leopard? Any ideas of what I might need to do?

http://support.apple.com/kb/HT1747
follow this link. see if it helps.

HP D110 AIO printer. Prints jam when printing with wireless, but not when hooked to USB cable! HELP!

I have a HP D110. It jams the paper when I print with wireless, but not when I use USB cable. Any ideas?

From what you describe you are having issues printing from MS Office. Have you had trouble printing from other resources on your computer (e.g. from the internet or another program)? The first thing I am going to suggest is that we start by uninstalling and reinstalling the printer from the resources available online.
First if you use a USB cord, make sure to remove it (this is important). Do not plug it back in until the software directs you to. Then go through the Devices and Printers, Programs and Features and Device Manager folders and insure that all copies, files, and programs related to the printer are removed. Then as directed, restart the computer.
In the START menu type "%temp%" and press ENTER. Here I want you to press Ctrl+A and hit DELETE. Some of the files will not allow you to delete them, skip those files and delete the majority that allows it.
http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=3562006&lang=en&cc=us...
Install that and let me know the result!
Have a great day!

[Solved] Realtek RTL8188SU wireless USB - not listed in ifconfig

Similar Messages

Maybe you are looking for