[SOLVED] Rebooted and now no Internet

I rebooted and the LAN cable is in and lit up but no network connectivity on my arch box.
Worked fine until i rebooted.
What do I check?
Last edited by CaptainKirk (2009-12-10 10:45:34)

This Windows box says:
Microsoft Windows [Version 6.0.6001]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:\Users\kirk>ipconfig
Windows IP Configuration
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . : home
Link-local IPv6 Address . . . . . : fe80::f1f4:3a2a:4a84:f5f1%10
IPv4 Address. . . . . . . . . . . : 10.0.0.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 10.0.0.138
Tunnel adapter Local Area Connection* 6:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . : home
Tunnel adapter Local Area Connection* 7:
Connection-specific DNS Suffix . :
IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e50:416:2715:f5ff:fffe
Link-local IPv6 Address . . . . . : fe80::416:2715:f5ff:fffe%12
Default Gateway . . . . . . . . . : ::
and arch box says:
[kirk@localhost ~]$ /sbin/ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:1E:8C:DE:ED:85
inet6 addr: fe80::21e:8cff:fede:ed85/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:134 errors:0 dropped:0 overruns:0 frame:0
TX packets:39 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:13549 (13.2 Kb) TX bytes:5670 (5.5 Kb)
Interrupt:27 Base address:0xe000
[kirk@localhost ~]$ /sbin/route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default * 255.255.255.0 U 202 0 0 eth0
[kirk@localhost ~]$ cat /etc/resolv.conf
# Generated by dhcpcd from eth0
# /etc/resolv.conf.head can replace this line
domain home
nameserver 10.0.0.138
# /etc/resolv.conf.tail can replace this line

Similar Messages

  • I have downloaded updates for microsoft office and now the internet wont work - any ideas?

    I have downloaded updates for microsoft office and now the internet wont work - any ideas?

    If you want to simply do a 'fresh' install (versus wiping out all of your data and doing a 'clean' install) simply boot to your Recovery partition (hold down the Command and R keys whilst booting) and when the Recovery screen appears, elect to freshly install OS X.
    Don't know that will solve your problem, though... did you do the 'automatic' update or download the update as a disk image (.dmg)? I wouldn't think that would be causing your problems...
    Clinton

  • HT4623 My iPhone4s updated to 7.1.1 and now my internet and email is not working. I need help?

    Sorry, I'm new to this, I installed IOS 7.1.1 on my iPhone 4s and now my internet and email is not working. 
    I have googled this on my computer and can't find any reference to this sort of problem.
    I need help. 
    Thanks in advance. 

    Try this:
    Go to Settings > General > Reset > Reset Network Settings
    See if you are able to connect now.

  • HT1725 My phone reboot and now my ringtone are gone how I get them back

    My phone reboot and now my ringtone are gone how I get them back

    You can get your information back if you have previously done a backup in iTunes or iCloud. 
    http://support.apple.com/kb/HT1766
    Go to this site and click on how to restore from backup. 
    This will help you with putting the information back onto your device.

  • I upgraded my iPad to version 5.0, I had a message on my Setting to upgrade the software to version 5.0.1, I select install and during installation my iPad2 star rebooting and now doing it non stop. I have no time to restore or do anything

    Hi,  I upgraded my iPad to version 5.0, I had a message on my Setting to upgrade the software to version 5.0.1, I select install and during installation my iPad2 star rebooting and now doing it non stop. I have no time to restore or do anything. My ipad rebooting every 2 or three minutes

    See Here
    iPad Unable to Update or Restore
    http://support.apple.com/kb/ht4097

  • I had my mac rebooted and now I can't find appleworks any idea where to download this?

    I had my mac rebooted and now I can't find appleworks any idea where to download this?

    "Rebooting" means restarting &, as fruhulda said, that won't cause things to disappear. If you mean you had the hard drive erased & the system reinstalled, you will have to find the original disk with the AppleWorks installer.

  • I have a MackBook Pro I updated to Maverick and now my internet won't work and all my programs freeze and I have to restart my computer.

    I have a MackBook Pro I updated to Maverick and now my internet won't open and all my programs freeze and I have to restart my computer. The only program that doesn't freeze is Microsoft Word.

    Back up your documents and everything else important to you, not that there is any reason to believe your hard disk may be failing, but the symptoms you describe may presage an impending disk failure, and you should have backups anyway.
    To help determine the possible causes of this behaviour read the following. None of what follows is intended to fix anything, but it will provide the additional information required to advance troubleshooting:
    Boot OS X Recovery by holding ⌘ and r (two fingers) while you start your Mac. At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red.
    When it finishes restart your Mac and test again for operation. If it's still not behaving as you expect it should, please post the results of EtreCheck in accordance with the following instructions:
    Apple Support Communities contributor etresoft wrote a very useful app to quickly gather certain system information that may help point to a cause of this problem. Go to his website, download and run EtreCheck:
    http://www.etresoft.com/etrecheck
    Etrecheck will be in your Downloads folder. Open it from there. You may see the following dialog box:
    Click Open - etresoft contributes to this forum frequently and can be considered a trustworthy developer.
    It will take a moment to run as it collects its data.
    Copy and paste its output in a reply.
    Do not be concerned about anything that says "Problem" or “failed” or anything else that may appear in red.
    EtreCheck was designed to remove any personal information (such as your computer's name and serial numbers) but if you see anything that looks like an email address or any other personal information that should not be divulged to others, please delete or obscure that information when you post the reply.
    When you are finished with EtreCheck, quit the program. It occupies very little space, and you can keep it or drag it to the Trash as you wish.
    After completing the above please determine if the problems also occur in "Safe Mode":
    Safe Mode or "Safe Boot" is a troubleshooting mode that bypasses all third party system extensions and loads only required system components. Read about it: Starting up in Safe Mode
    You must disable FileVault before you can start your Mac in Safe Mode.
    Starting your Mac in Safe Mode will take longer than usual, graphics will not render smoothly, audio is disabled on some Macs, and some programs (iTunes for example) may not work at all.
    Merely starting your Mac in Safe Mode is not intended to resolve the problem, it's to observe its performance without certain additional components.
    To end Safe Mode restart your Mac normally. Shutdown will take longer as well.

  • Hey, I just installed ML on my OCZ Octane SSD, everything went ok, However, it got stuck while rebooting and now I can only see flashing question mark icon and ML won't boot at all. Only in safe mode...

    Hey, I just installed ML on my OCZ Octane SSD, everything went ok, However, it got stuck while rebooting and now I can only see flashing question mark icon and ML won't boot at all. Only in safe mode...

    It looks like ocz is aware of the issue and trying to address it via firmware:
    http://www.ocztechnologyforum.com/forum/showthread.php?103700-Mountain-Lion-and- OCZ-Octane-Petrol-and-Octane-S2-SSD-s
    It's a shame because apple is clearly the party that changed something.

  • Ipod 4 rebooted and now cant activate

    ipod 4 rebooted and now cant activate

    Not really knowing what you mean by activate:
    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • Hello, I received a message to set my icloud and the screen went blank, the computer will reboot and now asks me for a PIN code unknown to me, what should I do?

    Hello, I received a message to set my icloud and the screen went blank, the computer will reboot and now asks me for a PIN code unknown to me, what should I do?

    It has been remotely locked by the owner, or by someone who knows the owner's Apple ID and password.

  • Just got an update for my iMac and now my internet locks up

    Just got a software update and now my internet locks up

    Reset the Router and Modem and if your router needs it please update it's firmware.

  • I updated from Snow Leorard to Moutain Lion and now my internet will not recognise  my password. All other comps use the network but my Mac upgraded Mac Mini keeps coming up with either 'timeout' or 'user or password not recognised' ...help!

    Hello all
    I upgraded from Snow Leopard to the latest Mountain Lion OS and now my Wifi will not work. When I try and insert the password to my Wifi network states either 'connection timed out' or 'password and/or user name not recognised' please help...!

    Take each of the following steps that you haven't already tried, until the problem is resolved.
    Step 1
    Restart the router. Many problems are solved that way.
    Step 2
    Change the name of the wireless network, if applicable, to eliminate any characters other than letters and digits. You do that on your router via its web page, if it's not an Apple device, or via AirPort Utility, if it is an Apple device.
    Step 3
    From the menu bar, select
     ▹ System Preferences... ▹ Network
    Click the Assist me button and select Assistant. Follow the prompts.
    Step 4
    Back up all data.
    Launch the Keychain Access application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Keychain Access in the icon grid.
    Enter the name of your wireless network in the search box. You should have one or more "AirPort network password" items with that name. Make a note of the name and password, then delete all the items. Quit Keychain Access. Turn Wi-Fi off and then back on. Reconnect to the network.
    Step 5
    You may need to change other settings on the router. See the guidelines linked below:
    Recommended settings for Wi-Fi routers and access points
    Potential sources of interference
    Step 6
    Make a note of all your settings for Wi-Fi in the Network preference pane, then delete the connection from the connection list and recreate it with the same settings. You do this by clicking the plus-sign icon below the connection list, and selecting Wi-Fi as the interface in the sheet that opens. Select Join other network from the Network Name menu, then select your network. Enter the password when prompted and save it in the keychain.

  • Installed Mac OS Lion and now have internet problems??

    So, I've installed the new Mac OS Lion on my MacBook Pro and now can only connect to the internet using Firefox - no Safari, no app store or anything else for that matter.  Has anyone else experienced the same problems?
    I've never had this problem on Snow Leopard and when I go through the Network Diagnostics it says that the internet connection (Wi-Fi) is perfect?!
    What's going on?? 
    I'm now having serious doubts of why I upgraded...

    Check out this troubleshooting guide:
    http://osxdaily.com/2011/07/22/wifi-dropping-in-os-x-lion-fixes/?utm_source=feed burner&utm_medium=feed&utm_campaign=Feed%3A+osxdaily+%28OS+X+Daily%29
    Best of luck

  • Iphone keeps shutting off and rebooting and now won't turn back on

    My iphone has shut itself off and rebooted 7 times today, and now it won't turn on anymore. What could be the problem? No home bottom to try and reset, so if I need that to fix my problem then I am out of luck.

    HI Good Morning,
    NO Worries For Your Iphone, the Battery Of your iphone 5c needs a Replacement.
    Visit Apple Store.

  • Updated Airport Exteme to 7.2.1 and now no internet!

    Ran update, and now I cannot get to thge internet. Checked with ISP and confirmed base station is registered and recieving proper IP Address, Local Computers appear to get good addresses from base station DHCP. Network diagnostics shows green lights down through ISP and Yellow for Internet & Server.
    Any help out there? I have bypassed base station for now & cabled iBook through Modem so I know that works!

    I had similar problems after upgrading. Would occasionally loose internet connection and NAT-PMP wasn't working in Azureus. I also reverted back to v7.1.1 and things are working fine again.

Maybe you are looking for

  • Report exection problem for one user - not able to see the data.

    Hello Friends , Need some help . I have got the one ticket from bussniess side about the report execution . Unfortunately , I am also not having authorisation of that report due to sensible data. Problem - User is executing the report but some how he

  • Elderly Mother Being Charged For Work That Wasn't ...

    I wonder if someone can point me in the right direction please to get this resolved, I'm at the end of my rope here. A couple of months back my 82 year old mother moved in to a retirement flat.  The flat had a variety of old unnecessary BT kit (trail

  • How do you match the audio and text with the typer writer effect in Final Cut Pro?

    I am making a video and I want to sync up the text with the audio using the typer writer effect.  For example I want when the music makes a bing noise I want a letter to pop up.  How do you set the exact time for each letter that comes up instead of

  • CRM Portal Integration

    I have a stand alone CRM system. I created a user and assinged him CRM Sales Manager role in the back end as well as in the Portal. Also I gave the user necessary RFC Authorization and BSP APPL authorization. I can see all the related tabs and iViews

  • OCIDateTimeFromText problem

    Hi All, I'm writing some c/c++ code and need to integrate with Oracle DB. I have problem when I'm trying to convert datetime string to OCIDateTime. connect to Oracle sword ociret; ociret =  OCIDescriptorAlloc ( envhp,  (dvoid**)&mesg->my_date,  OCI_D