[solved] Sound very quiet

Sorry, already solved.
"amixer set Front unmute 100%" fixed the problem. Strangely enough, i muted and unmuted each and every playback device via alsamixer many times.
If you have similar problems try these three commands:
amixer set Master unmute 80%
amixer set Front unmute 100%
amixer set Headphone unmute 100%
Hello,
my sound is very very quiet. To hear something I have to turn my amplifier up to at least 1/2 volume. At that volume level it would usually be enough to be wake the neighbourhood.
I checked with alsamixer if the sound output was muted but it isn't. What's strange is that the sound output worked just fine today but a restart suddenly the sound was very quiet like this.
Any ideas what's causing this?
Mainboard is MSI H55M-ED55 with sound chip ALC889.
06:53:26 ~ > cat /proc/asound/cards
0 [Intel ]: HDA-Intel - HDA Intel
HDA Intel at 0xfbdf4000 irq 22
Last edited by demian (2010-02-08 06:01:55)

Hi Charrison21989,
Welcome to the Apple Support Communities! I understand that you have been having some issues with the audio quality coming from the receiver on your iPhone 5. I suggest going through the steps in the following article to try and isolate and resolve the issue.
iPhone: Receiver and call audio quality issues
http://support.apple.com/kb/ts5196
I hope this helps,   
-Joe

Similar Messages

  • Very quiet sound in my Lumia 620

    Hello,
    I have a problem with a speaker to talk in my Lumia 620. I have installed Windows Phone 8.1. When I bought this phone sound from this speaker was loud but now after few mounths it is very quiet. My volume is set for max. What to do with it?
    Please help.

    With WP8.1 there are separate volume controls for different functions .. Hope you are setting them correctly ..
    See THIS

  • Sound is very quiet !

    Hi
    I recently bought a zen mp3 from 32 GB
    but now I've put some songs on it and the sound is very quiet, even when I put it on 25 !
    my brother has a zen mp3 of 8 GB and his sound is very loud at 25.
    Does anyone knows how i can get the songs to play louder?
    thanks
    sjesches

    Hi,
    I had a similar problem with my ZEN, the sound was just too low for my requirements as I listen to it a lot along busy roads where there is a lot of noise. I assume that you have the European firmware on your ZEN, check it, the European firmware ends in an "e". If so, you might try downloading and installing the US firmware which you can download from the US site. Download the US firmware first before throwing out the European firmware, then install the US firmware. This is much louder than the Euopean firmware, I believe this is because in Europe the authorities want to protect their young people from ruining their hearing and therefore restrict the volume of players.
    Now that I have the US firmware on my ZEN I have no problem with the sound anymore.
    Have fun with your player!
    macqueline.

  • A new Mac Mini seems to have a very quiet constant squeaking sound, is this normal?

    Hi everyone,
    I just purchased a brand new Mac Mini (i5) yesterday, and today in my very quiet room noticed that there is a very quiet squeeking sound coming from the unit (I believe it is near the front of the machine, opposite where the ports are). It is constant and changes pitch very slightly - but when there is a chirping noise from the hard-drive doing work, I think it stops then comes back straight after.
    Any idea's if this is a problem and if I should be worried? It's just a bit annoying.
    I have the latest 2013 i5 model.
    Thanks everyone,
    John.

    If you purchased the full AppleCare service support extended plan with automatic enrollment with the Mini computer, and you get a new one (or refurbished) ask that the Plan coverage be moved to the replacement Mac. Or refunded if you choose to wait & want to re-think your next product. They may be able to re-credit your method of payment, if a credit card.
    I usually read through the product support discussion forums to see what the patterns of issues are, since that may be an indicator of a sort within a narrow specific build series model & sub-year version; and am watchful of graphic card problems in models where the parts may be difficult or costly to replace, if at all, later on.
    At least with a Mini, you can choose several display adapters and hope to get a good match with whatever kind of display or digital TV you may wish to try & use as a screen. Some don't do all that well, & others do better.
    Good luck & happy computing!

  • Heartbeat sound suddenly quieter!!

    I put the heartbeat sound from imovie effects into my film and it was fine: I could adjust the volume within frames etc. and it played back perfectly. But I just watched it for the sixth time and suddenly the heartbeat sound is very quiet. I have all the volumes I can find turned all the way up. Not only that, but it is also very quiet when it is played FROM THE MENU. That is, when I double-click heartbeat in the menu, the volume is very low. Everything else is nice and loud. ***?!? This is messing up my film, and I cannot find a way to adjust the volume of this one sound effect. Please help!!
    ibook   Mac OS X (10.4.5)  
    ibook   Mac OS X (10.4.5)  

    Here's what worked for me. It's not a workaround, this acutally solved the problem and I haven't had speaker issues since.
    Go to "Activity Monitor" (you can hold "Command" "Shift" and press "U" if you're on the desktop).
    Locate "coreaudiod" under "All Processes"
    Right click it and click on "Quit"
    After several seconds, "coreaudiod" will restart on it's own and your speakers will return to normal.
    I tested this by restarting to see if it was a fluke workaround. Then I turned it off and waited a day (I had things to do so the waiting a day was easy lol). Turned it on, it was fine. I put it on sleep mode, waited 10 mins. and took it off of sleep mode. It was fine. Everything went back to normal for me.
    Let me know if this worked for you.

  • Incoming ichat convo very quiet

    Hey Guys,
    Just trying to get a podcast going in GB3. Myself and a buddy are audio chatting on ichat, except he comes in quiet on my end. I have to turn up my system volume to a good 3/4 of the way to hear him properly.
    When trying to import into GB3 i hit the record button, the import ichat convo window comes up and we each get a track... but i am on both tracks... and so is he... but he is very very quiet. Now if we could get eachother on seperate tracks (like i thought would happen) i could probally boost the track volume of his track to make his volume slightly louder, but chances are it will be still on the quiet side.
    He is using a usb mic and i am using a line mic through a small mixer. We are both on powermac G5s.
    Basically how can i boost his volume on my end and how can we be on 2 seperate tracks in sound as well as the screen?
    Thanks in advance
    Ryan

    all the volumes are cranked on his end... and its still coming in quiet in garageband on my end... and its still doubling the voice tracks on each indivisual tracks.
    he trid on his garageband on his end (GB2) and its coming in loud and as it should....
    anyone have any ideas?

  • Very Quiet Audio During Playback

    Hi,
    Just trying out my iPod 5G and an Apple AV cable.
    Video is fine but audio is very very quiet. Have to have the iPod set to virtually full volume and TV up to about 50 (normal volume on TV is 12-15) to get anything like listenable audio.
    The videos are fine through headphones with sound when volume is set to approx 25%.
    I am using Handbrake on the Mac to encode into MPEG-4 format.
    Any ideas ???
    Regards
    NIALL 8-)
    iPod 5g 60gb Firmware 1.1.1

    This is the way it works for everybody, your unit is not malfunctioning.

  • My guitar is very quiet when trying to record? How can I make it louder?

    I just got a new iMac and am using GarageBand to record some guitar and it is very quiet even with everything maxed out (gain and volume on focusrite saffire pro 14, track and master volume, and amp sim volume). Is there anyway to make it louder? Chain is Fender Deluxe Lone Star Strat > Saffire Pro 14 > FireWire cord> iMac. Thank you.

    Hi The App,
    When you're plugged in, does the light that says "Inst" light up on the PRO 14?  This indicates an instrument level input, and can be activated through Saffire Mix Control.  Near the bottom of the window, make sure the channel your guitar is coming in through has "Inst" selected, rather than "line" (also make sure you turn down the gain before you do this).  Let me know if this solves your issue.
    Best Regards,
    David Tichauer // Focusrite Technical Support

  • Realtek ALC888 (OSS Mixer) Very Quiet

    xfce4-mixer says I am using "Realtek ALC888 (OSS Mixer)" and the speakers and mic work, but the speakers are VERY quiet. I can't hear well enough to make a phone call with Skype. So I tried this:
    http://wiki.archlinux.org/index.php/Xfc … ew_Xfce4.6
    and it's not any better (I rebooted after I did that just to be sure). I have the volume on the physical speakers on 100% and xfce4-mixer also set to 100%.
    I know that these speakers are actually pretty loud because other distros were LOUD.
    Any suggestions how to debug this?
    Thanks.

    To clarify, I don't actually care if I use oss or alsa or a
    kerosene-powered dust buster. I just want to be able to hear youtube and
    Skype normally. And the problem isn't just Skype--also youtube is very
    quiet.
    I removed oss and alsa was still there. Or it claimed to be. I rebooted
    but amixer and alsaconf were 'command not found'
    I installed oss again and soundon gave a crazy output about conflicting
    drivers. So I rebooted. When I now click on my Xfce mixer panel addon it says
    GStreamer was unable to detect any sound devices. Some sound system
    specific GStreamer packages may be missing. It may also be a permissions
    problem.
    So I added myself (once again) to the audio group and installed oss again. Now I see this:
    [kirk@localhost ~]$ /etc/rc.d/oss restart
    :: Stopping Open Sound System [BUSY] /etc/rc.d/oss: line 18: /usr/sbin/soundoff: Permission denied
    [FAIL]
    :: Starting Open Sound System [BUSY] /etc/rc.d/oss: line 8: /usr/sbin/soundon: Permission denied
    [FAIL]
    [kirk@localhost ~]$ sudo /etc/rc.d/oss restart
    :: Stopping Open Sound System [BUSY] OSS not loaded.
    [DONE]
    :: Starting Open Sound System [DONE]
    [kirk@localhost ~]$ ossinfo
    Version info: OSS 4.1 (b 1052b/200905252233) (0x00040100) GPL
    Platform: Linux/i686 2.6.29-ARCH #1 SMP PREEMPT Wed May 20 07:06:02 UTC 2009 (localhost)
    Number of audio devices: 7
    Number of audio engines: 11
    Number of mixer devices: 1
    Device objects
    0: osscore0 OSS core services
    1: oss_hdaudio0 Intel HD Audio interrupts=502 (507)
    HD Audio controller Intel HD Audio
    Vendor ID 0x808627d8
    Subvendor ID 0x103c2a59
    Codec 2: ALC888 (0x10ec0888/0x103c2a59)
    2: oss_usb0 USB audio core services
    Mixer devices
    0: High Definition Audio ALC888 (Mixer 0 of device object 1)
    Audio devices
    HD Audio play front /dev/oss/oss_hdaudio0/pcm0 (device index 0)
    HD Audio play rear /dev/oss/oss_hdaudio0/pcm1 (device index 1)
    HD Audio play center/LFE /dev/oss/oss_hdaudio0/pcm2 (device index 2)
    HD Audio play side /dev/oss/oss_hdaudio0/pcm3 (device index 3)
    HD Audio play pcm4 /dev/oss/oss_hdaudio0/pcm4 (device index 4)
    HD Audio rec mix /dev/oss/oss_hdaudio0/pcmin0 (device index 5)
    HD Audio rec mix /dev/oss/oss_hdaudio0/pcmin1 (device index 6)
    /dev/dsp -> /dev/oss/oss_hdaudio0/pcm0
    /dev/dsp_in -> /dev/oss/oss_hdaudio0/pcm0
    /dev/dsp_out -> /dev/oss/oss_hdaudio0/pcm0
    /dev/dsp_mmap -> /dev/oss/oss_hdaudio0/pcm0
    /dev/dsp_multich -> /dev/oss/oss_hdaudio0/pcm0
    I am a bit lost now.
    EDIT But now when I click on the mixer it says "Sound card: High Definition Audio ALC888 (OSS v4 Audio Mixer)" and when I select controls there are approximately sixty options. Really, sixty.
    Last edited by CaptainKirk (2009-06-10 07:32:33)

  • Front Right Speaker Very Very Quiet!!

    Hello,
    I have a Creative Inspire P5800 (5.1) Speaker System & my sound card is Creative Sound Blaster Live 24-Bit. All purchased about Septemeber this year, all has been working fine until today when the front right speaker has gone very very quiet!? All other speakers work fine, Can anyone help?
    Cheers,
    Oidest

    I am having the exact same problem and there is no reply to any post on this issue what so ever on the internet.
    I have all the other speakers working perfectly. I have tested the speakers on another 5.1 source and they all work fine.
    This is such a pathetic problem, which is definitely routed somewhere in the drivers.
    I have absolutely no idea where to go.
    I used to be able to turn off the Hardware Acceleration to zero and then all 5 speakers would magically work. However now when I do that it is only coming out of speaker (Centre front).
    Can't you fix your drivers Creative? I am sending this back to you for creating sub-standard drivers for your hardware.

  • My keyboard clicks suddenly go very quiet or disappear completely

    When I start typing I can usually hear them but a few words in usually, they just disappear or go very quiet, they come back after a while but it gets very irritating. Right now, typing this, they've disappeared and came back thrice.
    All sounds are on, side switch on, keyboard clicks on.

    See if this helps.
    Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

  • Audio playback is very quiet after Windows 8.1 upgrade on Pavilion g7

    I recently updated to Windows 8.1 trial version and the audio playback is very quiet through the laptop speakers. Through headphones or played through the TV it works great.
    I have a Pavilion g7.
    When I check the drivers they tell me that I have the most recent divers.
    Any help would be greatly appreciated.

    Hello, @Nautic-Al 
    Welcome to the HP Forums.
    I see that you're having an audio issue with the notebook. I would like to try to help you with this.
    As you're using a Trial version of Windows please read this document: HP PCs - About Beta or Preview Software.
    To go along with that I will provide you this document for troubleshooting: No Sound from Speakers (Windows 8).
    If that does not help you, then you'll have to revert back to the installed OS or completely upgrade to a non trial version.
    Thank you for posting on the HP Forums.
    I worked on behalf of HP.

  • Very Quiet G3 iBook!

    The sound that my wife's much-loved old G3 white iBook gives out is very, very quiet. It makes listening to music quite a chore.
    She has turned up the output volume to maximum in System Preferences, iTunes and various Applications but all to no avail.
    Any ideas?

    Have you tried _resetting the PRAM_? The speaker volume setting is stored in PRAM, so resetting it may help.

  • Ipad keyboard clicks very quiet...

    Hi. I have noticed that my iPad keyboard clicks seem very quiet particularly when compared to my iPhone 4. The keyboard sounds are on maximum and when I plug in the headset they are fine. All other sounds on the iPad seem fine. I am not sure but I am pretty sure the sounds on the keyboard used to be louder. Has anyone else noticed this? Don't have access to another iPad to test it so any comments would be extremely helpful.
    Many thanks,
    Rob

    Well, I have to tell you that I was experiencing the same with my iPod and my iPhone, the iphone's keyboard clicks sounded very louder than the touch's, and wasn't a matter of speaker power or volume. I tried to restore, and It seemed to resolve this issue
    Hope this helped

  • Microphone is very quiet

    So I am currently using a Logitech G430 headset, and my skype seemed to make my microphone very quiet. I had not always had this issue, it just seemed to pop up one time. My mic is still picking up sound, just only when I hold it directly to my mouth. I have tested my mic multiple times and it works great, just doesn't seem to work on skype. It works on occasion and sometimes would fix itself if I plugged it in and unplugged it but so far it does not seem to work.

    Hi
    Did you check the microphone recording level?
    The microphone level settings can be found in Microphone Level Utility.
    Press and hold on the speaker icon on the task bar and select recording devices form the sub menu. Select Microphone and tab Properties.
    On the level tab move the Microphone slider to increase or to decrease the microphone level.
    If you feel the microphone volume level is inadequate, move the Microphone Boost slider to a higher level.
    PS: this and other details about your device can be found in user manual ;) so read it if you want to know how your device functions and how to use it

Maybe you are looking for

  • Captivate 7 Click box and bottons not able to open an URL on a new window

    I inserted a button and a click box in CP7 to open an URL on a new window. The URL opens but in a New Tab. There is an issue that the URL cannot be opened on a NEW WINDOW, I am using IE and Chrome. Do you have any ideas about this issue and how to tr

  • Excessively large "Sound Mute" Notice on Toshiba 32RL900A

    Having owned the 32RL900A for a couple of years, I have become disenchanted with the large size and placement of the "Sound Mute" caption on screen. Whilst it is possible to turn the volume down so that it is inaudible and no notice is visible, this

  • Timeline code to document class code - best practices

    I'm starting to put all of my code in the document class instead of on the main timeline, and I have a few questions. When I was using the timeline, everything was linear. It was easy to know when things would start and end because of how the playhea

  • Add New Virtual Network Interface to RRAS

    In the past (W2k3), adding an interface to the OS would also cause that interface to be added to RRAS.  I have a server running RRAS and it has multiple VMs running in Hyper-V.  I want to add an isolated VM that has a single port available from the I

  • 5.0.2 update failed to install

    I originally tried to update this with the Adobe update manager and that failed.  Then I tried to download the update and install manually (DVD version) and that failed. Any ideas? Using windows Vista Ultimate x64 SP2 Nvidia Quadro 3800 I have the CS