SOLVED: SPA2102, WRP400, SPA8000, SRP521 and SRP521-U FAX NSE fails with empty Payload c0000000
Hi Experts.
In my SIP network there is a Cisco PGW 9.6(1) used as PSTN gateway. PGW call agent controls many Cisco AS5400 via MGCP. We use Linksys SPA2102 to connect fax and modem devices.
Both PGW and AS5400 are configured to support FAX passthrough upspeeding via NSE event. Also SPA2102 devices are configured to support FAX passthrough NSE.
After many tests and debugs I see that SPA2102 doesn't recognize NSE event sent from AS5400.
From debug and wireshark traces you can see that AS5400 sends NSE 192 event correctly (see attachments).
So I've try to compare this scenario with a working one. The only difference is in the Payload content of NSE messages.
With AS5400 the Payload is c0000000. I think tath this is an empty payload while with different gateway or ATA the payload is c096c4e. In this last case SPA detects correctly NSE message.
Is this a BUG of SPA2102?
Thanks.
Hi experts, I updated this post after several months because we need information about the status of this issue.
Now we are using the firmware 2.00.21 for WRP400 (a beta) and the firmware 5.2.10 for SPA2102 devices.
No news about next release of WRP400 and the last software for SPA 5.2.12 doesn't fix this issue.
Now we must take a decision for buying thousand CPE for current year. If this issue will not fixed during this month we will be forced to change products and vendor !!!
I hope in a your positive response.
Regards.
Similar Messages
-
Hi Folks,
We have a report thats has been running well in production for more about 18 months. This month it did not complete execution.
We did implement BIA couple of 4 months back and the run times have drastically reduced after the BIA. Now this query execution results in a Dump with and without BIA. FYI the underlying cube has 195,876,020 records only.
Name of Runtime error: EXPORT_TOO_MUCH_DATA
Short text: Too much data for export.
What happened? Runtime error
The current ABAP program "CL_RSR_CACHE_DO_SPID==========CP" had to be
terminated because one of the statements could not be executed at runtime.
Error analysis: The dataset stored under an EXPORT/IMPORT ID is restricted
by
1. The maximum possible size of 2 GB
2. The length of a data record and the capacity of the sequence counter. This error occurs only if the capacity of the
sequence counter does not go beyond 255.
Source Code Extract:
1 METHOD if_rsr_cache_data_object~get_xstring.
2
3 FIELD-SYMBOLS:
4 <l_xstring> TYPE xstring,
5 <l_sp> TYPE ANY,
6 <l_spinfo> TYPE ANY.
7
8 CREATE DATA r_r_xstring.
9 ASSIGN r_r_xstring->* TO <l_xstring>.
10 ASSIGN n_s_spid-r_sp->* TO <l_sp>.
11 ASSIGN n_s_spid-r_spinfo->* TO <l_spinfo>.
12
13 *... Sp has to be the first component
>>>>> EXPORT sp = <l_sp> spinfo = <l_spinfo>
15 TO DATA BUFFER <l_xstring> COMPRESSION ON.
16
17 ENDMETHOD.
Referred to the below note 0001232573
which says to have 'RSRCACHE_ITAB_COMPR' parameter using report SAP_RSADMIN_MAINTAIN
Note say the below (It might be a little tricky, to find an appropriate value for 'RSRCACHE_ITAB_COMPR' as it heavily depends on the query-specific data structures that are stored in the cache. The general recommendation would be to start with a value of about 5000. Test this with a query, that dumped previously. In case the dump persists reoccurs, reduce the value of the parameter significantly. Otherwise, if no dump occurs but you face noticeably longer runtimes, increase the parameter.)
We are trying not able to get to the right parameter value. (changed it from 5000, 4000, 3000, & 1000) without much help. Did any of you had to change this parameter. How low or High can this parameter be changed?
We would like to understand if changing any other parameters would help in RSADMIN table would help?
Any thoughts from the experts would be appreciated
Thanks,
FHFHi,
Are you running the report for all the selections(all the data )?
execute the report with data selection and check?
Is the data in the Ic - compressed?
Regards
KP -
SSIS package runs from BIDS and by Executing package, but failing with Job
I have SQL Serve 2012 SSIS. I have problems to run from SQL Server Agent Job.
Steps runs SSIS package without configuration file. Package Run64BitRuntime is False in BIDS.
Package is runned by SQL Server Agent Service Account.
Server does not have Office 2010/2013 installed. Should it be installed?
ERROR1:
Description: The requested OLE DB provider Microsoft.ACE.OLEDB.12.0 is not registered.
If the 64-bit driver is not installed<c/> run the package in 32-bit mode.
ERROR2: (here SSIS package is trying to import XML source, but cannot file file)
Description: An error occurred with the following error message: "Could not find file 'D:\Integration\Metadata\'.".
Kenny_IHi Kenny,
It seems like you are using Excel as source file right? If yes, then please follow below steps:
Edit the job step and Check the option: Use 32 bit run time. Below is the screenshot for the same.
Please let me know for any questions.
Thanks, Madhu -
Calendar server and address book server login fails with outlook connector
Hi all,
I have installed Java Communication Suite 5 according to the doc http://blogs.sun.com/factotum/resource/comms5-install-linux.html.
When i deploy the connector i get the pop ups saying "Server:servername:3080
Error:service not available" also
"Server:servername:80/uwc"
Error:service not available"
asking to login to calendar server and address book server.Clicking "OK" allows install.
In outlook i can send and receive mails but not the meeting requests.It gives the error "login to calendar server" when i create a meeting request.
Please let me know what i have to do to get rid of the error.The username and passwd entered is correct.
Regards,
lmeenakshyHi,
When i deploy the connector i get the pop ups saying
"Server:servername:3080
Error:service not available" also Do you get exactly what you say above, or have you substituted in the real server name for "Server:servername:" above?
I would check through the outlook connector deployment configuration to verify that you have inserted valid information into all of the host & port fields - perhaps check the .ini file that is created to see if it has "Server" and "servername" listed.
"Server:servername:80/uwc"
Error:service not available"You are able to log into UWC via the web-interface and access your calendar/pab and edit/modify/delete calendar & addressbook entries right? The services are all up?
asking to login to calendar server and address book
server.Clicking "OK" allows install.The outlook connector deployment software gives you the option to increase the logging level, try that and see what the logs say - what was it trying to connect to/check which failed.
In outlook i can send and receive mails but not the
meeting requests.It gives the error "login to
calendar server" when i create a meeting request.
Please let me know what i have to do to get rid of
the error.The username and passwd entered is
correct.I suspect this is more of an underlying configuration issue that needs to be sorted out, once that happens you shouldn't have to keep logging in.
Regards,
Shane. -
My iPhone 3GS suddendly couldn't connect to the mobile provider's network. As I was in a rural place, I though this was because of bad coverage. It was then still possible to use Wi-Fi. After a while the phone asked to connect to itunes and gave the following warning: unknown IMEI and unknown ICCID.
I tried recovering it but procedures failes after hours with error 1002.
Is there a fix for this problem or do I need to go to a service center?Thanks Carolyn, I've tried all the options, but still it does not finish the recovering process. It stops with still a half millimeter on the statusbar .
Will probably just have to go to a service center. I already read that more people have the same problem and no one found a solution. As I am abroad and my iPhone largely exceeded the warranty time, I wonder what they will charge. -
Demote Server and Remove AD DS Role fails with "the target principal name is incorrect"
Hi all,
I am attempting to demote a domain controller so i can remove the AD DS role and have the server just its own workstation.
This domain controller has never replicated the domain and DS services were/are not working. We didnt discover this until the other domain controller died and has since been rebuilt with a brand new domain. The old domain no longer exists whatsoever.
So as said, I'm trying to demote this server, there is no domain to tidy up afterwards. However even with force removal option I'm getting the DFS Replication error: "the target principal name is incorrect". I do not exactly require
it do this myself, there is nothing to replicate anymore, i just need the DC demoted or role completely removed. There are no other DC's to transfer FSMO's or anything like that as its to be completely stand-alone.
Does anyone have any ideas how this role can be forcibly removed other than using the " force removal option " in ADDS config wizard?
Any help will be gratefully appreciated.
Thanks in advance
PhillHi Phill,
You can try to use Ntdsutil.exe to perform metadata cleanup.
If this doesn’t work, then I agree with Ed that you would need to reinstall the machine.
More information for you:
Clean Up Server Metadata
http://technet.microsoft.com/en-us/library/cc816907(v=WS.10).aspx#bkmk_commandline
Best Regards,
Amy -
Site to site VPN RV215W and SRP521: malformed ISAKMP Hash Payload
Hi
I have been struggeling with this problem for one week and tried all configuration (except the right one)
I have Two Cisco (one RV215W and one SRP521)
the SRP521 was used as client - server configuration and works fine
I wanted to move into a site to site config behind an internet box (using NAT to make things more complex)
On Site G
(LAN)192.168.25.0/24 === 192.168.25.1(CISCO RV215X)192.168.10.161 192.168.10.1(xDSL) 88.B.C.D (where 88.B.C.D is my public adress on site G
On Site R
(LAN)192.168.15.0/24 === 192.168.15.1(CISCO SRP521)192.168.1.2 192.168.1.1(xDSL) 41.F.G.H (where 41.F.G.H is my public adress on site R
So I have NAT (So I have activated NAT traveral on both side)
On the RV215W (Site G)
IKE Policy Table
Mode:main
Local identifier : 192.168.10.161
Remote identifier 192.168.1.2
AES128/SHA1
DH Group2
xauth disabled
VPN policy table
Type:autopolicy
remote endpoint 41.F.G.H
Local 192.168.25.1/255.255.255.0
remote 192.168.15.1/255.255.255.0
AES128/SHA1
PFS Keygroup: disable
On site R (SRP521W)
IKE
Policy Name gnt
Exchange Mode Main
Encryption Algorithm AES128
Authentication Algorithm SHA-1
Diffie-Hellman (DH) Group Group 2 (1024 bit)
Auto Pre-Shared Key XXXXXXXXXX
Enable Dead Peer Detection Enable
DPD Interval 3600
DPD Timeout 3600
XAUTH client Disable
IP Sec
Status Enable
Policy Name rabat
Local Group Type IP Address & Subnet
Local Group IP Address 192.168.15.1
Local Group IP Subnet 255.255.255.0
Remote Endpoint IP Address
Remote security gateway address 192.168.10.161
Remote security domain name
Remote group type IP Address & Subnet
Remote group IP 192.168.25.1
Remote group Subnet Mask 255.255.255.0
Encrypted algorithm 3DES
Integrity algorithm SHA-1
Police type Auto
Manual encryption key
Manual auth key
Inbound SPI
Outbound SPI
PFS Disable
Key life time 7800
Now using IKE police gnt
This are the logs
6 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: sending notification PAYLOAD_MALFORMED to 41.F.G.H:4500
7 2014-04-02 0:08:05 AM debug pluto[22201]: | 46 5f b1 08 95 86 af 15 b4 06 f9 a4 5a f6 d8 ad
8 2014-04-02 0:08:05 AM debug pluto[22201]: | payload malformed after IV
9 2014-04-02 0:08:05 AM info pluto[22201]: "rabat" #2: malformed payload in packet
10 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: malformed payload in packet
11 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: byte 2 of ISAKMP Hash Payload must be zero, but is not
12 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: Dead Peer Detection (RFC 3706): enabled
13 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_128 prf=oakley_sha group=modp1024}
14 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: new NAT mapping for #2, was 41.F.G.H:500, now 41.F.G.H:4500
15 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3
16 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: Main mode peer ID is ID_IPV4_ADDR: '192.168.1.2'
17 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: STATE_MAIN_R2: sent MR2, expecting MI3
18 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2
19 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): both are NATed
20 2014-04-02 0:08:04 AM debug pluto[22201]: "rabat" #2: STATE_MAIN_R1: sent MR1, expecting MI2
21 2014-04-02 0:08:04 AM debug pluto[22201]: "rabat" #2: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1
22 2014-04-02 0:08:04 AM debug pluto[22201]: "rabat" #2: responding to Main Mode
23 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]
24 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 109
25 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 109
26 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 109
27 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [RFC 3947] method set to=109
28 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [Dead Peer Detection]
29 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: ignoring unknown Vendor ID payload [4f4543714271574c644b7a41]
I guess that the error is byte 2 of ISAKMP Hash Payload must be zero, but is not
I could not find any real hint on the internet/forums about this errorHi
I have been struggeling with this problem for one week and tried all configuration (except the right one)
I have Two Cisco (one RV215W and one SRP521)
the SRP521 was used as client - server configuration and works fine
I wanted to move into a site to site config behind an internet box (using NAT to make things more complex)
On Site G
(LAN)192.168.25.0/24 === 192.168.25.1(CISCO RV215X)192.168.10.161 192.168.10.1(xDSL) 88.B.C.D (where 88.B.C.D is my public adress on site G
On Site R
(LAN)192.168.15.0/24 === 192.168.15.1(CISCO SRP521)192.168.1.2 192.168.1.1(xDSL) 41.F.G.H (where 41.F.G.H is my public adress on site R
So I have NAT (So I have activated NAT traveral on both side)
On the RV215W (Site G)
IKE Policy Table
Mode:main
Local identifier : 192.168.10.161
Remote identifier 192.168.1.2
AES128/SHA1
DH Group2
xauth disabled
VPN policy table
Type:autopolicy
remote endpoint 41.F.G.H
Local 192.168.25.1/255.255.255.0
remote 192.168.15.1/255.255.255.0
AES128/SHA1
PFS Keygroup: disable
On site R (SRP521W)
IKE
Policy Name gnt
Exchange Mode Main
Encryption Algorithm AES128
Authentication Algorithm SHA-1
Diffie-Hellman (DH) Group Group 2 (1024 bit)
Auto Pre-Shared Key XXXXXXXXXX
Enable Dead Peer Detection Enable
DPD Interval 3600
DPD Timeout 3600
XAUTH client Disable
IP Sec
Status Enable
Policy Name rabat
Local Group Type IP Address & Subnet
Local Group IP Address 192.168.15.1
Local Group IP Subnet 255.255.255.0
Remote Endpoint IP Address
Remote security gateway address 192.168.10.161
Remote security domain name
Remote group type IP Address & Subnet
Remote group IP 192.168.25.1
Remote group Subnet Mask 255.255.255.0
Encrypted algorithm 3DES
Integrity algorithm SHA-1
Police type Auto
Manual encryption key
Manual auth key
Inbound SPI
Outbound SPI
PFS Disable
Key life time 7800
Now using IKE police gnt
This are the logs
6 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: sending notification PAYLOAD_MALFORMED to 41.F.G.H:4500
7 2014-04-02 0:08:05 AM debug pluto[22201]: | 46 5f b1 08 95 86 af 15 b4 06 f9 a4 5a f6 d8 ad
8 2014-04-02 0:08:05 AM debug pluto[22201]: | payload malformed after IV
9 2014-04-02 0:08:05 AM info pluto[22201]: "rabat" #2: malformed payload in packet
10 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: malformed payload in packet
11 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: byte 2 of ISAKMP Hash Payload must be zero, but is not
12 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: Dead Peer Detection (RFC 3706): enabled
13 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_128 prf=oakley_sha group=modp1024}
14 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: new NAT mapping for #2, was 41.F.G.H:500, now 41.F.G.H:4500
15 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3
16 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: Main mode peer ID is ID_IPV4_ADDR: '192.168.1.2'
17 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: STATE_MAIN_R2: sent MR2, expecting MI3
18 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2
19 2014-04-02 0:08:05 AM debug pluto[22201]: "rabat" #2: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): both are NATed
20 2014-04-02 0:08:04 AM debug pluto[22201]: "rabat" #2: STATE_MAIN_R1: sent MR1, expecting MI2
21 2014-04-02 0:08:04 AM debug pluto[22201]: "rabat" #2: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1
22 2014-04-02 0:08:04 AM debug pluto[22201]: "rabat" #2: responding to Main Mode
23 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]
24 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 109
25 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 109
26 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 109
27 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [RFC 3947] method set to=109
28 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: received Vendor ID payload [Dead Peer Detection]
29 2014-04-02 0:08:04 AM debug pluto[22201]: packet from 41.F.G.H:500: ignoring unknown Vendor ID payload [4f4543714271574c644b7a41]
I guess that the error is byte 2 of ISAKMP Hash Payload must be zero, but is not
I could not find any real hint on the internet/forums about this error -
[SOLVED] Blinking screen - new Xorg and Intel issue
Screen is blinking after opening laptop lid no matter what i did (nothing, lock screen, hibernate, standby). It blinks every 10-20 seconds for about 1-2 seconds, and cpu% used by X's raises from 0.3-1.0 to even 10% and system slows down a little in that moment. My Xorg logs:
$ cat /var/log/Xorg.0.log
(II) Video Bus: Found keys
(II) Video Bus: Configuring as keyboard
(II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event2"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
# closing & opening laptop lid
# right after opening (properly i suppose)
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "CMO", prod id 4609
(II) intel(0): Using EDID range info for horizontal sync
(II) intel(0): Using EDID range info for vertical refresh
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): EDID vendor "CMO", prod id 4609
# after 10-20 seconds
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "CMO", prod id 4609
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): EDID vendor "CMO", prod id 4609
# over and over...
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "CMO", prod id 4609
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): EDID vendor "CMO", prod id 4609
Blinking stops when i restart computer.
I have newest xorg and intel drivers (xorg-server 1.7.1.901-2 & xf86-video-intel 2.9.1-1). I tried also downgrade this (and related) packages to older versions (even xorg-server 1.5.* & xf86-video-intel 2.4.*) and the same happens... with only one difference. On that oldest packages I've tried screen doesn't blinks, but the wallpaper of the desktop is changing: my -> default -> my -> default... with the same frequency . I was googling a lot, believe me. I study IT on a University and I asked my friends from there, and they just run out of ideas. In addition i can write that it isn't my laptop fault because windows xp works fine and ubuntu 9.04 (i had before archlinux) also worked good. It has started on ubuntu 9.10, so I thought I move to archlinux, and its still here? I suppose its a problem with intel drivers or xorg, but somehow linked with power management of the monitor(?). But why then older packages don't work? Please, I will be grateful for any help.
My /etc/X11/xorg.conf file generated by 'Xorg -configure' command:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "glx"
Load "dri2"
Load "record"
Load "dbe"
Load "dri"
Load "extmod"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
#Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -HSync -Vsync
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "ShadowFB" # [<bool>]
#Option "DefaultRefresh" # [<bool>]
#Option "ModeSetClearScreen" # [<bool>]
Identifier "Card0"
Driver "intel"
VendorName "Intel Corporation"
BoardName "Mobile 915GM/GMS/910GML Express Graphics Controller"
BusID "PCI:0:2:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Last edited by joda (2009-12-01 09:49:38)SOLVED!!! Must enable KMS => switch off vga option in grub, and replace it with "i915.moduleset=1"
-
Hi! I just bought Lion and I am having a problem with the installation. It keeps telling me that the computer's hard drive has a S.M.A.R.T. problem. How can I solve it?
Thanks!
AngelaYou may have a hard drive problem. When I installed Lion, the installer told me that it couldn't complete because the hard drive was failing (or broken, the exact words escape me). Since the HD had been functioning just fine, I took it to the Genius Bar, and found out that yes, the hard drive was slowly dying (bad sectors). I couldn't reboot into Snow Leopard, the installer wouldn't let me and then the drive just wouldn't work at all.
I had to replace my drive and restore from Time Machine. Thankfully, I had Time Machine, and had just done a backup 5 minutes before the crash.
Best of luck. -
when I use Mail and want to paste an emailadress with a right mouse click in the adres field this doesn't work, ofcourse cmd V works. How can I solve this
YAY! That did it.
Thank you so much.
And a Very Happy and Prosperous New Year to you!
bonnie -
Hi this is alamzeb , i have purchased OS X mountain lion from apple store and installed it on my macbook with the expect ion of making my macbook faster but it become more slow by installing os x , how can i solve this problem
alamzeb wrote:
Hi this is alamzeb , i have purchased OS X mountain lion from apple store and installed it on my macbook with the expect ion of making my macbook faster but it become more slow by installing os x , how can i solve this problem
Have a read under the threads on the Right hand side of this page under 'More Like This'
Pete -
I'm having problems with 7.1 update my flash "flashes" now when I receive txt's and notifications! And I'm also having problems with freezing and wifi problems! How do I solve this?
Doh! Rectified flash!
But when face timing 2 seconds after it connects wifi disconnects? Any thoughts -
[SOLVED] transmission-daemon segfaulting, trapped, and others
Hey guys,
Originally I was having the same problem with Rtorrent when I hit about 4000 torrents. Now I'm slightly above 6000 torrents with Transmission, and it has recently started crashing with messages like these in the syslog:
[1556037.507253] traps: transmission-da[2855] general protection ip:457c12 sp:7fc301ad7b00 error:0 in transmission-daemon[400000+75000]
[1784992.236136] transmission-da[2884]: segfault at 4377000043e4 ip 0000000000457c12 sp 00007f07c5134b00 error 4 in transmission-daemon[400000+75000]
[2030052.408358] traps: transmission-da[13344] general protection ip:457c12 sp:7fab58b66b00 error:0 in transmission-daemon[400000+75000]
and these are the 3 just from this boot. I have a theory it only starts to happen after the system has been running for a few days, but I've just rebooted it to see if crashes in the same fashion.
Regardless, since this also happened with rtorrent at fewer torrents, I'm thinking I could be experiencing memory corruption. Is there a reliable way to check for this, without putting down the system for too long? I have a webserver serving 2 sites, which I'd prefer didn't stay offline for too long - but if there are no alternatives, then so be it.
Thanks,
gonX
Last edited by gonX (2013-05-18 14:17:40)Solved, it was a RAM issue. Replaced all the sticks and now it has been running for weeks without a crash.
-
I can not create a new ID in my iphon 4s, well I've created several to solve the problem of FaceTime, and the last restoration would not let me create a new ID.
I can do?
Thanks for helping.Thanks Ckuan
I can do, to create new ID?
No way to delete all information from Iphon to create another ID?
I will appreciate your answer -
I have a new iphone 5. After update and download some programs I can not just turn it on and shown in the LCD "iTunes" with a picture of a USB cable. - Can anyone help me solve the problem. thanks
Its trying to tell you to connect it by usb to a computer to reflash a failed firmware flash
You should comply
Maybe you are looking for
-
Site License query ...
How much will it cost the school I work at to license Adobe CC for a site license?
-
I am having trouble with aliasing artifacts when using my AVCHD camera. Has anyone been able to overcome this with imovie?
-
My Ipod nano 5th gen lost all of my podcasts and will not download anything from ITunes
All my content on my Ipod nano 5th ed disappeared, and it will not download anything from ITunes. I restoered original content. My operating system is up to date. My capacity is 8 gigs. What more should I do?
-
Hi, With a PIX, I believe that each access list match is on a 'per tcp flow' basis not on a 'per matching packet' basis. Is this the same for routers or do routers match on a per packet basis?? Thanks
-
Can't install conkyclementine-bzr
More than ten days trying to install conkyclementine-bzr, but without success.See what message displays yaourt: [rado@archbox ~]$ yaourt -S conkyclementine-bzr ==> Downloading conkyclementine-bzr PKGBUILD from AUR... x PKGBUILD x conkyclementine-bzr.