[solved] Suddenly no permissions on specific USB flash drive

Hi,
since yesterday I can't delete or create new files on my primary USB flash drive.
I then tried my other USB drive and it works without a problem.
Both are from the same manufacturer and formated with the FAT16 file system. When I check the permissions of the files/folder I see myself as owner with read/write permissions on both drives.
the error message on the console is:
rm: cannot remove 'foo': Read-only file system
I'd really like to give you more information but honestly I don't know where to look since one works and the other suddenly stopped working.
\edit: Checked dmesg:
[ 769.912866] FAT-fs (sdb1): error, fat_get_cluster: invalid cluster chain (i_pos 123716903)
[ 769.912871] FAT-fs (sdb1): Filesystem has been set read-only
Seems to be the problem. Any ideas?
Thanks in advance!
Last edited by Barghest (2012-06-20 07:06:48)

I wasn't aware that FAT filesystems had a concept of file permissions or ownership...
First of all, reboot if you recently updated your system. Because the linux package (the kernel) was also updated. Then install and use gparted to format the drive.

Similar Messages

(SOLVED) Full install on a 2gb USB flash drive?

So here's the deal, I am not sure if this is the best place to post this. I am a newbie so I am just thinking out of my %^& here.
I love Arch more than any other distro, and I want to bring it with me. As of now I use Arch on my laptop and desktop. However it's missing on my work computer. It would be best if I didn't mess with the work computers, so I am curious about installing Arch on a USB.
If I went with a minimal install, keeping things around 1.5gb with most applications and whatnot installed, would I be able to boot it and work with it and not have any problems?
How could this be done, would it be possible to:
- Partition the USB, one partition for the boot (ext 2, primary boot) and another partition for / and home etc.
If this does in fact work, would it be slow as death running completely off a USB? If that's the case how difficult would it be to copy the system to RAM but keep /usr running off the USB so configs and files could be saved?
I know there are other distros that work well off a USB like Puppy Linux (which supports saving configs and files etc.). I have been using lubuntu live because it is similar to my Arch setup, but doesn't support saving onto the USB. I would prefer to stick with Arch the whole way.
Last edited by Google (2010-06-24 14:34:06)

running from USB for me has been WAY worth the learning of grub2 and all the other things. I run a 16 gig stick and an 8 gig stick. standard installs and have grub 2 doing double duty to boot other ISOs when desired. The 8 gig stick has 2 partitions and arch boots sweetly off partition 2. I have gotten good enough at manually modifying the grub2 cfg file. I don't use any of the errr, clever stuff that's spread out in /etc for grub2. heck with that I thought!
Also: I just mount some other drive to save bigger files. Have a vbox file on the internal drive that can esily be moved around as well. Totally totally ARCH works fantastic as a stock install on USB. I figured why complicate/dilute my learning (as I'm only approaching advanced ability) by even thinking about other distro. If there's wasn't ARCH I'd go BSD, which would be very challenging due to drivers, flash, vbox etc. Just My brief though here.
UPDATE: forgot the point somewhat. Thinking to add here: I get (regular install of) ARCH to run on a 1 gig flash stick which coincidentally I'm creating right now. In fact it has a vfat partition 1 and an 800 meg ext2 partition 2. Lots of ways to trim stuff out after install. There's a couple of threads about deleting locals and stuff here. Can save, I think it was 2 or 3 hundred meg quickly.
One thing is running a windows manager and not a desktop environment of course/obviously.
best wishes to all!
Last edited by yvonney (2010-06-27 18:32:20)

USB Flash Drive not detected after OS X Mountain Lion installed.

My MacBook Air 11 inch (Mid 2011) suddenly stopped detecting all my USB flash drives a week after upgraded to Mountain Lion.
I have a tiny 16GB USB flash drive (Sandisk Cruzer Fit), for daily work, that has never been unplugged from my MBA.
Everything was fine on Lion, and a week of Mountain Lion, until just when my MBA prompted me that my flash drive "was not ejected properly" after I re-opened the display/lid, or from sleep mode.
I thought I might have accidentally removed the flash drive unknowingly. So I tried re-plugging the flash drive, closed and re-opened the MBA lid, and the same error message "The disk was not ejected properly" occured. I repeated the steps for a few times (thinking my flash drive might be faulty) and at my last attempt, the flash drive was stopped detected. I tried several USB flash drives and external hard drives (of various brands) to both the USB ports of my MBA, only the external hard drives were detected (on both USB ports) and functioning. None of the flash drives was detected on either USB port.
The tested flash drives were plugged to another 13" MacBook (Unibody, Late 2008, OS X Lion) and they all worked fine.
I wonder if anyone faces the same problem, and solution(s) please?
Additional: OS X Mountain Lion re-installed and same problem occurs / No problem with OS X Lion.

I had the same issue after installing Mountain Lion from the App store. The issue is you are missing the IOUSBFamily.kext extension amongst others. The solution is to backup your macbook, then perform a clean install of Mountain Lion.
I had this done at the Apple Store and now everything is restored as well as performance speed being improved.
Note: When restoring your files (a clean install will delete all your files and applications), use the Migration Assistant.
I would recommend going to the Apple Store to do this because they can perform the clean install from a USB which is so much faster than the download form the App store.
Hope this helps.

Advice on allowing specific file types to be written to USB flash drive

We currently have all of the Removable Storage Access policies enabled (Computer Config > Policies > Admin Templates > System/Removable Storage Access) and would like to know if it is possible to allow specific file types to be exempted from this
policy. Specifically we need to allow certain users to write to USB flash drive but need to limit to MS Office files only. Is this possible?
Thanks in advance for any assistance.
-Mike

> Specifically we need to allow
> certain users to write to USB flash drive but need to limit to MS Office
> files only. Is this possible?
Third party products can do that. GPO cannot.
Martin
Mal ein
GUTES Buch über GPOs lesen?
NO THEY ARE NOT EVIL, if you know what you are doing:
Good or bad GPOs?
And if IT bothers me - coke bottle design refreshment :))

[Solved]USB Flash Drive inaccessible.

Hi there.
I have installed Arch Linux on my Sony laptop and I have configured it so that most stuff works. The only problem I'm facing now, is that my USB Flash Drive won't show up when I plug it in. I have tried restarting ehci service, but it does not solve anything. I had this problem many years ago with another computer running Linux, but I can't remember how it got solved. Connecting a USB-mouse works perfectly but not a flash drive. The drive is a FAT32 formatted Kingston.
This is my dmesg log:
[ 109.300651] usb 2-1.3: new high-speed USB device number 4 using ehci_hcd
[ 109.613294] Initializing USB Mass Storage driver...
[ 109.613459] scsi7 : usb-storage 2-1.3:1.0
[ 109.613577] usbcore: registered new interface driver usb-storage
[ 109.613579] USB Mass Storage support registered.
[ 110.614456] scsi 7:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 2
[ 110.616674] sd 7:0:0:0: [sdc] 8237056 512-byte logical blocks: (4.21 GB/3.92 GiB)
[ 110.617821] sd 7:0:0:0: [sdc] Write Protect is off
[ 110.617835] sd 7:0:0:0: [sdc] Mode Sense: 03 00 00 00
[ 110.618550] sd 7:0:0:0: [sdc] No Caching mode page present
[ 110.618561] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 110.621899] sd 7:0:0:0: [sdc] No Caching mode page present
[ 110.621908] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 110.787723] sdc: sdc1
[ 110.880634] sd 7:0:0:0: [sdc] No Caching mode page present
[ 110.880647] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 110.880655] sd 7:0:0:0: [sdc] Attached SCSI removable disk
Running openbox with PCManFM. Any clues how to solve this?
Last edited by light (2013-03-17 21:26:26)

s1ln7m4s7r wrote:
For what i can see from the log there is no problem.
Have you tried to manually mount it? To see if it is a PCManFM issue. Also, have you checked this:
https://wiki.archlinux.org/index.php/PC … ge_devices
Hi.
I tried installing gvfs, apparently I uninstalled it for some reason before. But it did not help mounting the flash drive. So I tried mounting it manually and it worked (Yaay!). But it complained that my flash drive was not mentioned in fstab. So I looked in fstab and the only ones listed is my root partion "/" and "/home". So how do I add USB mounting to fstab? I'm a little bit confused.
And one off-topic question: Shouldn't my "/var" partion also be mentioned in fstab?
Thanks for helping me
Edit: This is how fstab looks right now
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
# /dev/sda2 LABEL=/
UUID=ed07bdb6-61c6-4cc7-b98d-122a869046f1 / ext4 rw,relatime,data=ordered 0 1
# /dev/sda4 LABEL=/home
UUID=7448100b-682b-430f-9e59-327ce6f9f22c /home ext4 rw,relatime,data=ordered 0 2
Last edited by light (2013-03-17 20:54:38)

Usb flash drive read only problem [solved]

Hi, im using spacefm, i have udevil and udisks2 installed, i can read my USB flash drive but i cannot delete files, i tried gparted that use spacefm as well and i can delete files from the usb flash drive with no problems, any ideas?
i solved i installed ntfs-3g and i can delete files again
thanks
Last edited by adcdam (2013-04-08 01:01:22)

I installed it and got this error : now my Macbook wont even see the flash drive...

[SOLVED]USB flash drive no longer showing up in /dev

My USB flash drives are no longer showing up in /dev. I also don't see them in /dev/disks/... either. Dmesg outputs:
[731969.826862] usb 1-1: new high-speed USB device number 5 using ehci_hcd
Any ideas on where to start?
Last edited by nadman10 (2012-09-26 22:12:22)

ls -l outputs:
Bus 001 Device 005: ID 0781:5530 SanDisk Corp. Cruzer
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5530 Cruzer
bcdDevice 1.00
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Bus 002 Device 002: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x045e Microsoft Corp.
idProduct 0x0040 Wheel Mouse Optical
bcdDevice 3.00
iManufacturer 1
iProduct 3
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 72
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 3.05
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.05
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255

[SOLVED] Clone Archlinux to USB flash drive

Hello,
I want to clone an existing Archlinux installation (x86-64) from a hard drive to a 32 GB USB flash drive. I want to be able to boot from the USB stick on my Win7 labtop.
I already took some measures to prepare my hard drive (with gparted). After moving all movies, pics etc to external stores and shrinking the home drive (sda4), it now looks like this:
- sda1 Boot (small)
- sda2 Swap (small)
- sda3 Root ( ca.8GB)
- sda4 Home (ca. 22GB)
I tried to take an image of the entire hard-disk (ca. 250GB) with clonezilla and restore it to the USB flash drive, but got an error message - original disk to big (250GB vs 32GB), besides only ca 30GB of the 250GB being assigned to partitions.
Now I'm looking for a way to bring only the necessary partitions from the harddisk to the USB stick, hoping to have exactly the same Archlinux configuration as a bootable installation on the USB stick afterwards (bootable on a Win7 labtop ... and maybe from my main Archlinux machine too). There is a wiki article about the topic, but its rather about installing a fresh system than cloning an existing system. The related questions on the forum (searching in 'installation' for 'clone usb') did not answer my question.
Maybe somebody did successfully what I'm planning to do and can give me some tips?
Last edited by 4on6 (2012-04-16 12:57:01)

4on6 wrote:Create two new partitions - with gparted p.ej.? And do I have to worry about the filesystems - must they be the same like for the original partitions on my hard-disk?
I prefer Gparted, it's easy as cake
The filesystems don't have to be the same as the original partitions. I prefer ext4 (universally supported) or jfs (uses very little CPU), but I recommend you ext4.
In fact, you can use a hard drive instead of a flash drive and this is how you clone a Linux installation manually!
4on6 wrote:So I mount both - source and destination partitions (/mnt/dest/ suggests it ...)?
Yes. I mount the source partition in /mnt/source and the destination partition in /mnt/dest, and then I issue
rsync -av /mnt/source/ /mnt/dest
and wait for it to finish. Then I unmount the partitions and mount the other ones and repeat the same thing.
4on6 wrote:I create that /boot folder on the flash drives root partition, right? Won't that cause problems later on with rsync, when I update the installation and there is an additional folder on the target partition?
Since the root directory you'll aready copy on the flash disk won't have the /boot directory, simple do a
mkdir /mnt/dest/boot
while your destination partition is still mounted. Unmount the source root partition, mount the boot one and then type:
rsync -av /mnt/source/ /mnt/dest/boot
and GRUB and the kernel will be copied to the /boot folder on the destinaton partition on the flash disk.
Make sure that in /mnt/dest/etc/fstab you comment out the line for mounting the /boot partition, if any.
4on6 wrote:I've seen those UUIDs as output of a linux command (mount? fdisk?), but I don't recall which one - how do I get these UUIDs?
Use Gparted, right click any partition and click Information. In the window that appears, in the middle you can double-click the UUID and press Ctrl-C to copy it. Then you can paste it in the text editor and use it for /etc/fstab or /boot/grub/menu.lst. That's why I love Gparted for such stuff.
4on6 wrote:Do I send this command from the live Arch-CD, and is it the only command necessary (I have not much experience with grub)?
Yes, since Arch uses GRUB 1 on the installation CD you can uste the command I gave you to reinstall GRUB on the flash disk with the settings you already entered for the /boot/grub/menu.lst file.
Make sure you boot the CD in 64 bit mode if the Arch you installed is 64 bit. Just to be safe.
4on6 wrote:I will ...
Be very careful, I didn't and lost ALL my files by mistake in typing. Triple-check the directory you are currently working in! ALWAYS make a backup!
4on6 wrote:Great that this is possible, hope I manage to get it done. Thanks again.
You're welcome. Please inform me if this little tutorial suited you so I can make a wiki entry for it, if the admins allow.

Usb flash drive not mounting when inserted (SOLVED)

Hi,
I am (now) using fvwm-crystal with rox as my file manager and when i insert a usb flash drive in to a usb port nothing happens. I check /media and nothing is there. Yes i do have hal started at boot.
I reinstalled arch with xfce4.
Last edited by theringmaster (2007-10-09 20:28:42)

Well, there are the on-line manual pages:
man ivman
man IvmConfigActions.xml
man IvmConfigBase.xml
man IvmConfigConditions.xml
man IvmConfigProperties.xml
And there are examples in the default files (/etc/ivman/) provided with Ivman.
But that you probably already know. I'm not familiar with any other docs, except maybe tutorials on the net if you count them as docs

How do I browse & play .mp3 files from a USB flash drive using Labview 8.0?

I'm a tester & want to test USB flash drives connected to PC.
I want to browse the file system & playback the audio files, .jpeg files etc in the USB drive. I've Labview 8.0. When I searched for some examples or VIs which can detect the USB flash drive, couldn't find any. So if you could point me in the right direction, I can find a solution to my problem.
Thanks.
Solved!
Go to Solution.

You probably won't find specific examples for this. A USB flash drive is mounted by the OS and appears as a new memory storage device to all software on the PC, including LabVIEW. You can certainly write a LabVIEW program to open files on the stick and play/run them but I would create a VI that wrote files to the stick and then read them back and checked them for bit-level errors. Keep in mind that your OS might be doing parity checking under the hood which would make your test rather meaningless.
BTW, testing memory by looking at pics or listening to MP3s would be useless of course. A human can't see or hear bit-level errors in a high bandwidth data stream.
Using LabVIEW: 7.1.1, 8.5.1 & 2013

USB Flash Drive not working

I have purchased a USB FLASH DRIVE v112b 16GB on 26.12.13 from HP
dealer in Agartala. after using 2 months I'm facing problems with it.
Suddenly an error is showing " you need to format the disk before you
use it but format is not possible as another error showing format not
possible. what should i do now with it?
Please solve my issues asap.
Neal

Hi Neal2014,
Welcome to the HP Forums!
I would like to take a moment and thank you for using the forum, it is a great place to find answers. For you to have the best experience in the HP forum, I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that you recently purchased a HP USB drive. You are now getting a message to format it, but are unable to. Have you tried to format it on a different computer?
If you are unable to format the drive, I suggest you call HP support, as I believe it will still be in warranty.
Please call HP technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. HP Technical Support Sitemap
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

4GB Toshiba TransMemory U2M USB Flash Drive problem

I would like to ask you to get help about one of your products that i bought few months ago.
I bought a 4GB Toshiba TransMemory U2M USB Flash Drive (enhanced for Windows ReadyBoost)
Supports the ReadyBoost function of Windows Vista
Write Speed: up to 3.9 MBytes/s
Read Speed: up to 21 MBytes/s
Large storage capacity
award-winning premium quality
5 years warranty
Which of specifications are written as above.
After I bought this product I used it to save some documents which includes some very important documents for my studies.
Now I have trouble with the product and can not get my documents.
The product cant not response when I plug in to computer.
I tried Toshiba USB Flash Drive some other computers also but it cant response in any case.
Is there any way to solve the problem and get my documents back. It did not damage or break.
thank you..

Hi
Usually if the HDD would start to malfunction then the data on this HDD are not more accessible and in most cases you cannot backup this data to any other place.
Of course there are many specialists and companies who could retrieve and could save the data from damage HDDs but this is very expensive procedure and dont think its worth to spend a lot money for private data..
However, you can get in contact with an local ASP (Toshiba authorized service partner) if your Toshiba product start to malfunction and is covered by warranty..

How to install USB flash drive in windows 7

Could anyone please help to install USB flash drive to Windows 7. This will enable me to hook up keyboard and mouse to my laptop. Thank you so very much for any assistance.

Hi,
Could you please help us to know what is your computer, Please use the following instructions for find out the model/product of your machine:
http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&cc=us&docname=c00033108
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Follow up question on recovery data on USB flash drive

HP instructions say the 32 GB flash drive should NOT be branded as Windows 8 compatible. I bought a Sandisk 32 GB yesterday for $20 on sale, but it says on the back it is compatible.
Other more/or less expensive flash drives did not address whether compatible with Windows 8.
I have Windows 8.1
Thanks in advance for your help...
This question was solved.
View Solution.

Hi,
If the flash drive is listed as 'Windows 8 compatible' it cannot be used - the reason is because the HP Recovery Media creation software looks for an external device and flash drives marked Win 8 compatible show as internal drives.
In the example below, the 32 Gb usb flash drive 'Dave G' shows as an internal drive which cannot be used, while the usb flash drive 'Removable Disk H' would work.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Looking for All on one with USB Flash Drive Print/Scan support

I am looking for an All in One Print/scan/copy. It should support print from USB Flash drive and scan to the same.
Thanks

Hi,
You may check the HP Officejet 6600/6700 models which support USB Flash drivers.
You may find the flash driver specifications listed within the Memory Device specifications below:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03058896&cc=us&dlc=en&lang=en&lc=en&product=505...
As well you may check the HP Officejet 8600 Series which supports both USB Flash Driver and Memory cards, its specifications can be located below:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02858465&cc=us&dlc=en&lang=en&lc=en&product=432...
Both of the products above provide Print, Scan, Copy and Fax functionality.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

[solved] Suddenly no permissions on specific USB flash drive

Similar Messages

Maybe you are looking for