(Solved) Trouble with installing on Crucial C300 Real SSD 64GB
Hello everyone. I've been trying to figure this out for the last three nights. I cannot get arch installed if I am using my ssd. The ssd is Crucial c300 64 GB firmware is 0006. It does not matter what I do if my ssd is connected I get to booting os in bios followed by a reboot with no error messages. I have tried many different things like allowing arch to manually partition the ssd, using ssd as home instead of root to no avail. Only thing I have not tried is adding a 1 mb partition to the beginning of ssd marked as ef02 as per the Arch SSD wiki. If anyone with this same ssd and firmware can chime to let me know if they had the same issue I would appreciate it. I do not have this problem with other distros. Ubuntu, Linux Mint, and LMDE have all installed fine on the ssd. Sorry if this is the wrong section for this.
Edit. Looks like I found out the problem. It was having quit boot enabled in the bios. I suppose I need to look into initreadahead if I want arch and my computer to play nice with that setting.
Last edited by nemesis2all (2011-02-21 13:40:28)
Check whether grub-install belongs to grub package or grub2 package. Try to install these updated grub2 packages from here
http://dl.dropbox.com/u/9710721/skodabe … pkg.tar.xz - for x86_64
http://dl.dropbox.com/u/9710721/skodabe … pkg.tar.xz - for i686
http://dl.dropbox.com/u/9710721/skodabe … pkg.tar.xz - any arch
and then follow the post_install instructions from grub2-bios package.
You might have to 'bind' mount /dev into your <chroot>/dev though or install the above packages and install grub2 from outside the chroot.
Last edited by skodabenz (2010-12-13 13:32:51)
Similar Messages
-
[SOLVED] Trouble with Install that I've never seen before (Gnucash)
Hello all! I am rather new to Arch. I came over from Windows (disgruntled up to Win 7). When I first came over to Linux I did so via Ubuntu (12.04 and 13.10) and Mint (16). Seeing that Ubuntu would love to eventually sell us all out I decided to give Arch a try and LOVED IT! The install went smoothly and almost every program that I have needed has installed flawlessly..That is with the exception of Gnucash. I do a lot of freelance bookkeeping work and Gnucash is most definitely the best program I have found out there (even when I was using Windows). I have tried to install from BOTH the official repository and the AUR with no luck. I am using a 64 bit install of Arch on a Dell Inspiron 1440. All of my packages and repositories have been updated through pacman -Syu and -Syy. Below is the results message that I receive when trying to install from EITHER repository (AUR version is what I have posted). It shows that there appear to be two corrupt packages. If any of you can guide me in the right direction as to how to possibly rectify my trouble I would be most appreciative. (Also: if I am posting this in the wrong area please let me know where the better place would be.)
[rick@rick_inspiron1440 builds]$ tar -xf gnucash-latest.tar.gz
[rick@rick_inspiron1440 builds]$ cd gnucash-latest
[rick@rick_inspiron1440 gnucash-latest]$ makepkg -sci
==> Making package: gnucash-latest 2.6.1-1 (Sun Feb 16 14:27:20 EST 2014)
==> Checking runtime dependencies...
==> Installing missing dependencies...
[sudo] password for rick:
resolving dependencies...
looking for inter-conflicts...
Packages (25): gconf-3.2.6-3 gnome-mime-data-2.18.0-6 gnome-vfs-2.24.4-8
guile1.8-1.8.8-3 gwenhywfar-4.3.3-4 ktoblzcheck-1.43-1
libart-lgpl-2.3.21-3 libbonobo-2.32.1-4 libbonoboui-2.24.5-2
libdbi-0.9.0-2 libglade-2.6.4-5 libgnome-2.32.1-4
libgnome-data-2.32.1-4 libgnomecanvas-2.30.3-2
libidl2-0.8.14-3 libofx-0.9.9-1 libxml++-2.36.0-1
opensp-1.5.2-4 orbit2-2.14.19-2 aqbanking-5.0.25-2
goffice0.8-0.8.17-2 gtkhtml-3.32.2-3 libdbi-drivers-0.9.0-2
libgnomeui-2.24.5-1 slib-3b3-3
Total Download Size: 1.28 MiB
Total Installed Size: 88.49 MiB
:: Proceed with installation? [Y/n] y
:: Retrieving packages ...
gtkhtml-3.32.2-3-x86_64 628.7 KiB 724K/s 00:01 [######################] 100%
libdbi-0.9.0-2-x86_64 642.2 KiB 415K/s 00:02 [######################] 100%
libdbi-drivers-0.9.... 35.4 KiB 668K/s 00:00 [######################] 100%
(25/25) checking keys in keyring [######################] 100%
(25/25) checking package integrity [######################] 100%
error: libdbi: signature from "Thorsten Töpper <[email protected]>" is unknown trust
:: File /var/cache/pacman/pkg/libdbi-0.9.0-2-x86_64.pkg.tar.xz is corrupted (invalid or corrupted package (PGP signature)).
Do you want to delete it? [Y/n]
error: libdbi-drivers: signature from "Thorsten Töpper <[email protected]>" is unknown trust
:: File /var/cache/pacman/pkg/libdbi-drivers-0.9.0-2-x86_64.pkg.tar.xz is corrupted (invalid or corrupted package (PGP signature)).
Do you want to delete it? [Y/n]
error: failed to commit transaction (invalid or corrupted package)
Errors occurred, no packages were upgraded.
==> ERROR: 'pacman' failed to install missing dependencies.
Last edited by rightwingrb (2014-02-19 00:28:41)rightwingrb wrote:Also...I have no idea what "code" tags are but hopefully the above is acceptable ;-)
When posting configs, code or command output, please use [ code ] tags https://bbs.archlinux.org/help.php#bbcode
like this
It makes the code more readable and - in case of longer listings - more convenient to scroll through.
Please remember to mark the thread as solved https://bbs.archlinux.org/viewtopic.php?id=130309
Last edited by karol (2014-02-18 22:23:24) -
i'm having trouble with installing a 8g kit in my late 2009 mac mini. when the parts are installed all i get is a beeping sound, is there any way to get around this?
What is the source & link to this 8 GB kit please?
Can you count the beeps or flashes?
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
Note: In this case, a flash is considered to be 1/4 second or 250 ms or greater in length.
http://support.apple.com/kb/HT1547 -
Trouble with installing on mac ppc 10.4.11
I can't install digital editions on my mac ppc running 10.4.11 it says when i try to install "error communicating with adobe id server. please try again later and it says E_AUTH_BAD_DEVICE_KEY. I keep trying, same result. Chatted with adobe, they couldn't help. any ideas. it worked before my puter crashed last time. Any answers????
>hi, using 7.2.1
>
>Re: Trouble with installing on mac ppc 10.4.11
>created by <http://forums.adobe.com/people/Derek+Leng>Derek Leng in
>Adobe Digital Editions -
><http://forums.adobe.com/message/4842875#4842875>View the full
>discussion
>Which ADE version do you use? I think ADE 2.0 supports Mac OS X
>10.6, 10.7, and 10.8 Intel only...
>
>Please note that the Adobe Forums do not accept email attachments.
>If you want to embed a screen image in your message please visit the
>thread in the forum to embed the image at
>http://forums.adobe.com/message/4842875#4842875
>
>Replies to this message go to everyone subscribed to this thread,
>not directly to the person who posted the message. To post a reply,
>either reply to this email or visit the message page:
>[http://forums.adobe.com/message/4842875#4842875]
>
>To unsubscribe from this thread, please visit the message page at
>[http://forums.adobe.com/message/4842875#4842875]. In the Actions
>box on the right, click the Stop Email Notifications link.
>
>Start a new discussion in Adobe Digital Editions by
><mailto:[email protected]m>email
>or at
><http://forums.adobe.com/choose-container!input.jspa?contentType=1&containerType=14&contain er=3355>Adobe
>Community
>For more information about maintaining your forum email
>notifications please go to
><http://forums.adobe.com/message/2936746#2936746>http://forums.adobe.com/message/2936746#2936746. -
Trouble with installing Mini SAP 7.0 on a USB Harddisk
Hi Community,
i have a problem with installing the Mini SAP 7.0 on my USB Harddisk.
The Installing Wizard is abort the Install by 17 %. I have the install wizard, about the night runnig, but nothing. 17 % is end.
Can me Help please.
Regards
Markus
Message was edited by:
Markus BechlerNo, its no Error Log on Display. The wizard end by 17 %.
On Wizard write, "Preparing packages for Installation"
Base 7.6.00.32 32 Bit
17%
there abort, and not reaktion. I musst restart, than is the Wizard going off.
My English is not the best,
Markus -
Help: Slow Crucial C300 256GB SSD in 17" MacBook Pro (2011) via SATA III 6Gb/s
Computer: 2011 17" MacBook Pro
Drive: Crucial C300 256GB
Drive Firmware: Revision 7
Bay: Main Drive Bay (6Gb/s)
OS: Lion 10.7.1
I did a fresh install of 10.7.1 and I'm getting these speeds on the above configuration:
Here is the same test run on my previous computer, a 2008 Mac Pro, with SATA II (same exact drive):
What is going on here? The Mac Pro with SATA II was running the C300 faster than the brand new 17" MacBook Pro 2011 running SATA III. This drive should be getting up up to 355MB/s read on SATA III.
Can someone please help me figure out why this drive is not running faster in my computer?
Thank you in advance.
FYI - I did install the new EFI 2.2 Update that was released in September. The above tests were after I installed the update! So you can rule out that I didn't install this update that supposedly fixed SATA speed issues on these Mac's.I solved it. Xbench didn't give the best results. I tried other benchmarking tools and concluded that I am getting the SATA III speeds on this drive on this MacBook Pro.
-
Trouble with install disks - is it OK to make a copy of them?
Finally, I am trying to make a copy of the install disks that came with my MBP. This was recommended in several threads for preserving the original and having backups just in case.
I used Disk Utility to make a disk image - choosing DVD/CD master, no encryption - as I was instructed on another thread. I made the disk images fine of the 2 disks - they are now saved as disk images in the .cdr format. While I was at it, I made a disk image of the TechTool Deluxe CD that came with my AppleCare.
When I inserted a CD (and then I tried a DVD) into the slot to Burn the disk image of the first (and then the second) install disk, I got the message that there is not enough room on the disk I am trying to use (for either disk). I had no trouble burning a disk of the TechTool Deluxe - I did that on a CD.
When I go to Get Info for the disk image for the 2 install disks, it looks like each is no larger than 5 plus GB, which seems strange.
What am I doing wrong?
Mrs HWhen you make images of the discs, it is compressed. So when you get info of the image, that is smaller than the actual disc size. You said disc two was 3.97gb but really uncompressed it is likely over 6GB. For both install discs one and two, you need dual-layer DVDs to burn.
Thanks for your help, mdpeterman.
I wondered about the compressed issue - but since I chose CD/DVD master, (from Disk Utility Help: "If you want to use the disk image with a third-party application, choose CD/DVD master. The disk image contains a copy of all sectors of the disk, whether they're used or not, and copies them to other CDs or DVDs bit for bit") with no encryption I assumed that the size of the disk image was identical to the original.
What you say tells me I'm wrong - that even with DVD master bit for bit, the image is compressed. Right?
I'll get back to you when I have solved this...
Mrs H
Mrs H -
Trouble With installing Snow Leopard on my 4 year old Macbook
I'm trying to install Snow Leopard to my 4 year old Macbook stuck on 10.5.8, but it keeps saying "The application 'Install Mac OS X' cannot be used from this volume." I've tried almost everything to solve this, but I can't find anything at really helps my situation. I've looked on some of these discussions, and they haven't really helped much. My Macbook has a: 2.4 GHz Intel Core 2 Duo, 2 GB 667 MHz DDR2 SDRAM, and is stuck on OS X 10.5.8. Please give me your input and help
Are you using a Retail version of Snow Leopard that looks like this?
Or gray discs that look like this?
The gray discs are machine specific and will only work with the MacBooks that they were shipped with. -
[SOLVED] Trouble with PipeLight
So I read through everything I could find on this and have no answers. I read the wiki and project FAQ before installing and realized I needed to make sure XATTR was enabled prior to compiling:
[xaero@archtop ~]$ xattr_test="$HOME/.wine-pipelight"; setfattr -n 'user.testAttr' -v 'attribute value' $xattr_test &> /dev/null; getfattr $xattr_test 2>&1 | grep -q user.testAttr && echo 'It works!' || echo 'No workie!'
It works!
I then compiled, and installed the package, as well as chromium (fresh install) and fired it up... instantly, chromium installed the pipelight plugin, and then continued business as usual. I then installed the UA Switcher plugin linked on the project page, and went to Netflix and tried to watch something. No dice; Netflix Error Code N8156-6205. What gives? Maybe that chromium bug applies to me as well; so I went ahead and forced the UA string from the command line:
[xaero@archtop ~]$ chromium --user-agent="Mozilla/5.0 (Windows NT 6.1; WOW64; rv:15.0) Gecko/20120427 Firefox/15.0a1"
[4759:10:1231/185916:ERROR:base_feature_provider.cc(122)] manifestTypes: Allowing web_page contexts requires supplying a value for matches.
[4694:4720:1231/185916:ERROR:base_feature_provider.cc(122)] manifestTypes: Allowing web_page contexts requires supplying a value for matches.
[4810:15:1231/185920:ERROR:base_feature_provider.cc(122)] manifestTypes: Allowing web_page contexts requires supplying a value for matches.
[PIPELIGHT:LIN:unknown] attached to process.
[PIPELIGHT:LIN:unknown] checking environment variable PIPELIGHT_SILVERLIGHT5_1_CONFIG.
[PIPELIGHT:LIN:unknown] searching for config file pipelight-silverlight5.1.
[PIPELIGHT:LIN:unknown] trying to load config file from '/home/xaero/.config/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:unknown] trying to load config file from '/etc/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:unknown] trying to load config file from '/usr/share/pipelight/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:silverlight5.1] sandbox not found / not installed!
[PIPELIGHT:LIN:silverlight5.1] GPU driver check - Your driver is supported, hardware acceleration enabled.
[PIPELIGHT:LIN:silverlight5.1] using wine prefix directory /home/xaero/.wine-pipelight/.
[PIPELIGHT:LIN:silverlight5.1] checking plugin installation - this might take some time.
[install-dependency] wine-silverlight5.1-installer is already installed in '/home/xaero/.wine-pipelight/'.
[install-dependency] wine-mpg2splt-installer is already installed in '/home/xaero/.wine-pipelight/'.
[install-dependency] wine-wininet-installer is already installed in '/home/xaero/.wine-pipelight/'.
wine: cannot find L"C:\\windows\\system32\\winemenubuilder.exe"
err:wineboot:ProcessRunKeys Error running cmd L"C:\\windows\\system32\\winemenubuilder.exe -a -r" (2)
[PIPELIGHT:WIN:silverlight5.1] windowless mode is off.
[PIPELIGHT:WIN:silverlight5.1] embedded mode is on.
[PIPELIGHT:WIN:silverlight5.1] unity hacks is off.
[PIPELIGHT:WIN:silverlight5.1] window class hook is on.
[PIPELIGHT:WIN:silverlight5.1] render toplevelwindow is off.
[PIPELIGHT:WIN:silverlight5.1] replaced API function CreateWindowExA.
[PIPELIGHT:WIN:silverlight5.1] replaced API function CreateWindowExW.
[PIPELIGHT:WIN:silverlight5.1] replaced API function TrackPopupMenuEx.
[PIPELIGHT:WIN:silverlight5.1] replaced API function TrackPopupMenu.
fixme:advapi:RegisterTraceGuidsW (0x2b1f87, 0x350118, {aa087e0e-0b35-4e28-8f3a-440c3f51eef1}, 1, 0x65f678, (null), (null), 0x350118): stub
[PIPELIGHT:WIN:silverlight5.1] init successful!
fixme:advapi:UnregisterTraceGuids 0: stub
[PIPELIGHT:LIN:unknown] attached to process.
[PIPELIGHT:LIN:unknown] checking environment variable PIPELIGHT_SILVERLIGHT5_1_CONFIG.
[PIPELIGHT:LIN:unknown] searching for config file pipelight-silverlight5.1.
[PIPELIGHT:LIN:unknown] trying to load config file from '/home/xaero/.config/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:unknown] trying to load config file from '/etc/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:unknown] trying to load config file from '/usr/share/pipelight/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:silverlight5.1] sandbox not found / not installed!
[PIPELIGHT:LIN:silverlight5.1] GPU driver check - Your driver is supported, hardware acceleration enabled.
[PIPELIGHT:LIN:silverlight5.1] using wine prefix directory /home/xaero/.wine-pipelight/.
[PIPELIGHT:LIN:silverlight5.1] checking plugin installation - this might take some time.
[install-dependency] wine-silverlight5.1-installer is already installed in '/home/xaero/.wine-pipelight/'.
[install-dependency] wine-mpg2splt-installer is already installed in '/home/xaero/.wine-pipelight/'.
[install-dependency] wine-wininet-installer is already installed in '/home/xaero/.wine-pipelight/'.
[PIPELIGHT:WIN:silverlight5.1] windowless mode is off.
[PIPELIGHT:WIN:silverlight5.1] embedded mode is on.
[PIPELIGHT:WIN:silverlight5.1] unity hacks is off.
[PIPELIGHT:WIN:silverlight5.1] window class hook is on.
[PIPELIGHT:WIN:silverlight5.1] render toplevelwindow is off.
[PIPELIGHT:WIN:silverlight5.1] replaced API function CreateWindowExA.
[PIPELIGHT:WIN:silverlight5.1] replaced API function CreateWindowExW.
[PIPELIGHT:WIN:silverlight5.1] replaced API function TrackPopupMenuEx.
[PIPELIGHT:WIN:silverlight5.1] replaced API function TrackPopupMenu.
fixme:advapi:RegisterTraceGuidsW (0x2b1f87, 0x350118, {aa087e0e-0b35-4e28-8f3a-440c3f51eef1}, 1, 0x65f678, (null), (null), 0x350118): stub
[PIPELIGHT:WIN:silverlight5.1] init successful!
fixme:advapi:UnregisterTraceGuids 0: stub
[PIPELIGHT:LIN:unknown] attached to process.
[PIPELIGHT:LIN:unknown] checking environment variable PIPELIGHT_SILVERLIGHT5_1_CONFIG.
[PIPELIGHT:LIN:unknown] searching for config file pipelight-silverlight5.1.
[PIPELIGHT:LIN:unknown] trying to load config file from '/home/xaero/.config/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:unknown] trying to load config file from '/etc/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:unknown] trying to load config file from '/usr/share/pipelight/pipelight-silverlight5.1'.
[PIPELIGHT:LIN:silverlight5.1] sandbox not found / not installed!
[PIPELIGHT:LIN:silverlight5.1] GPU driver check - Your driver is supported, hardware acceleration enabled.
[PIPELIGHT:LIN:silverlight5.1] using wine prefix directory /home/xaero/.wine-pipelight/.
[PIPELIGHT:LIN:silverlight5.1] checking plugin installation - this might take some time.
[install-dependency] wine-silverlight5.1-installer is already installed in '/home/xaero/.wine-pipelight/'.
[install-dependency] wine-mpg2splt-installer is already installed in '/home/xaero/.wine-pipelight/'.
[install-dependency] wine-wininet-installer is already installed in '/home/xaero/.wine-pipelight/'.
[PIPELIGHT:WIN:silverlight5.1] windowless mode is off.
[PIPELIGHT:WIN:silverlight5.1] embedded mode is on.
[PIPELIGHT:WIN:silverlight5.1] unity hacks is off.
[PIPELIGHT:WIN:silverlight5.1] window class hook is on.
[PIPELIGHT:WIN:silverlight5.1] render toplevelwindow is off.
[PIPELIGHT:WIN:silverlight5.1] replaced API function CreateWindowExA.
[PIPELIGHT:WIN:silverlight5.1] replaced API function CreateWindowExW.
[PIPELIGHT:WIN:silverlight5.1] replaced API function TrackPopupMenuEx.
[PIPELIGHT:WIN:silverlight5.1] replaced API function TrackPopupMenu.
fixme:advapi:RegisterTraceGuidsW (0x2b1f87, 0x350118, {aa087e0e-0b35-4e28-8f3a-440c3f51eef1}, 1, 0x65f678, (null), (null), 0x350118): stub
[PIPELIGHT:WIN:silverlight5.1] init successful!
[PIPELIGHT:LIN:silverlight5.1] using timer based event handling.
fixme:win:EnumDisplayDevicesW ((null),0,0x65f1c8,0x00000000), stub!
fixme:advapi:CreateProcessAsUserW 0x148 L"C:\\Program Files\\Silverlight\\5.1.20913.0\\agcp.exe" L"agcp.exe 37 320" (nil) (nil) 1 0x00004000 (nil) (null) 0x65f228 0x65f218 - semi- stub
fixme:heap:HeapSetInformation (nil) 1 (nil) 0
fixme:file:K32GetMappedFileNameW (0xffffffff, 0x4015f4, 0x50e1d4, 520): stub
fixme:d3d:resource_check_usage Unhandled usage flags 0x8.
fixme:urlmon:Uri_GetPropertyBSTR (0x10467a0)->(6 0x65e004 4)
fixme:process:GetNumaHighestNodeNumber (0x65eaa0): stub
fixme:thread:SetThreadStackGuarantee (0x65ea90): stub
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e6b0, (nil) 0x65e6a8
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e6b0, (nil) 0x65e6a8
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e880, (nil) 0x65e878
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e880, (nil) 0x65e878
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e540, (nil) 0x65e538
fixme:thread:GetThreadPreferredUILanguages 48, 0x65d488, (nil) 0x65d480
fixme:thread:GetThreadPreferredUILanguages 48, 0x65d488, (nil) 0x65d480
fixme:process:FlushProcessWriteBuffers : stub
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e470, (nil) 0x65e468
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e470, (nil) 0x65e468
fixme:thread:GetThreadPreferredUILanguages 48, 0x65ea00, (nil) 0x65e9f8
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e9c0, (nil) 0x65e9b8
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e8ac, (nil) 0x65e8a4
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e840, (nil) 0x65e838
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e818, (nil) 0x65e810
fixme:thread:GetThreadPreferredUILanguages 48, 0x65ecf0, (nil) 0x65ece8
fixme:thread:GetThreadPreferredUILanguages 48, 0x65ecb0, (nil) 0x65eca8
0
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e65c, (nil) 0x65e654
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e65c, (nil) 0x65e654
fixme:advapi:RegisterTraceGuidsW (0x10015fbb, 0x1008c460, {00000000-7ac4-430a-94e4-b0dfd254650f}, 1, 0xa9ae028, (null), (null), 0x1008c468): stub
fixme:ntdll:NtLockFile I/O completion on lock not implemented yet
fixme:advapi:RegisterTraceGuidsW (0xac83c2f, 0xae63a20, {00000000-7ac4-430a-94e4-b0dfd254650f}, 1, 0xa9ae338, (null), (null), 0xae63a28): stub
fixme:mountmgr:harddisk_ioctl returning zero-filled buffer for IOCTL_VOLUME_GET_VOLUME_DISK_EXTENTS
fixme:advapi:GetCurrentHwProfileW (0xa9ae290)
fixme:thread:GetThreadPreferredUILanguages 48, 0x65e81c, (nil) 0x65e814
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:NtQueryInformationThread info class 16 not supported yet
fixme:thread:GetThreadPreferredUILanguages 48, 0x65ecb0, (nil) 0x65eca8
fixme:thread:GetThreadPreferredUILanguages 48, 0x65ec44, (nil) 0x65ec3c
fixme:thread:GetThreadPreferredUILanguages 48, 0x65ec1c, (nil) 0x65ec14
fixme:thread:NtQueryInformationThread info class 16 not supported yet
Still no dice. Any ideas on what to try next?
Last edited by Xaero252 (2014-01-01 21:43:21)Hi Xaero252,
error N8156-6205 is DRM related, and could mean that either your DRM files are somehow corrupted
just delete them with (as a regular user):
rm -rf ~/.wine-pipelight
or that your Wine version is still compiled without XATTR support or missing some patches. Which package and/or patches did you use for Wine? When you're compiling it manually make sure that the patches apply cleanly, and that you run "autoreconf" before the compilation. You can find some more detailed instructions here, how to manually compile it.
Please note that the compilation of Wine is often a bit auto-magic, and its possible that XATTR support is not included, even if you did everything right (the problem occured mainly on ArchLinux so far). In this case a recompilation should help to fix the problem. We had a user with a similar problem in our channel #pipelight a few days ago, where the problem was also just solved by recompiling the package.
You can also take a look at this bug report some time ago, which was also caused by the fact that XATTR wasn't included somehow.
https://bugs.launchpad.net/pipelight/+bug/1216332
Sebastian -
[Solved] Trouble with WPA/WPA2 and wireless connections (ath9k)
Hi, I'm having some issues with my Arch install. Right now I'm posting this from Windows so I don't have precise logs, but I mostly remember the issue so bare with me.
I'm using ath9k with my Bigfoot Killer 1202 card (not sure what the exact model is), and I can't connect to my university's WPA/WPA2 access point. Using wpa_supplicant I get the error "4-way handshake failed - pre-shared key may be incorrect".
So after some digging I found that I can get it to authenticate with nohwcrypt=1, but when I rmmod ath9k && modprobe ath9k nohwcrypt=1 it enumerates itself as wlan0 (instead of wlp3s0, which is what I get from booting up).
Then I made the file /etc/modprobe.d/ath9k with the contents "options ath9k nohwcrypt=1" but it seems to still not want to connect until I rmmod && modprobe manually.
Can someone point me in the right direction on how to fix this issue? I haven't used Arch in a few years and a lot of things have changed, and so far it seems nothing works as I expect it to. Also, how do I get my wifi card to enumerate as the same device no matter when I load ath9k? I don't care if it's called wlan0 or wlp3s0, I just want it to stay the same.
Edit: Additional Info
lspci
03:00.0 Network controller: Qualcomm Atheros AR9462 Wireless Network Adapter (rev 01)
cat /sys/module/ath9k/parameters/nohwcrypt
[root@huxley pobegam]# cat /sys/module/ath9k/parameters/nohwcrypt
0
(so I guess it isn't loading from ath9k.conf on boot after all?)
wpa_supplicant output
<3>CTRL-EVENT-SCAN-RESULTS
<3>WPS-AP-AVAILABLE
<3>CTRL-EVENT-SCAN-RESULTS
<3>WPS-AP-AVAILABLE
<3>CTRL-EVENT-SSID-REENABLED id=0 ssid="Student"
<3>Trying to associate with 00:19:30:6b:1b:a2 (SSID='Student' freq=2412 MHz)
<3>Association request to the driver failed
<3>Associated with 00:19:30:6b:1b:a2
<4>WPA: Failed to set PTK to the driver (alg=2 keylen=32 bssid=00:19:30:6b:1b:a2)
<3>CTRL-EVENT-DISCONNECTED bssid=00:19:30:6b:1b:a2 reason=1 locally_generated=1
<3>WPA: 4-Way Handshake failed - pre-shared key may be incorrect
<3>CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="Student" auth_failures=2 duration=20
<3>CTRL-EVENT-SCAN-RESULTS
<3>WPS-AP-AVAILABLE
wpa_supplicant configuration file
[root@huxley wpa_supplicant]# cat sunyit.conf
ctrl_interface=/var/run/wpa_supplicant
update_config=1
network={
scan_ssid=1
ssid="Student"
proto=WPA
key_mgmt=WPA-PSK
pairwise=TKIP
group=TKIP
priority=1
psk="Wireless@SUNYIT"
Last edited by Pobega (2013-10-02 03:55:51)Update: It seems to work ONLY when I rmmod && modprobe; if I force nohwcrypt=1 at boot it doesn't seem to work. Seems kind of odd... Wonder if this is a kernel issue?
Edit: Also updated with dmesg (because I'm an idiot and forgot to include it)
[ 2.802118] hub 3-1:1.0: USB hub found
[ 2.802210] hub 3-1:1.0: 6 ports detected
[ 2.876377] e1000e 0000:00:19.0 eth0: registered PHC clock
[ 2.876380] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:90:f5:ea:54:ff
[ 2.876382] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 2.876418] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF
[ 2.876688] ACPI Warning: 0x000000000000f040-0x000000000000f05f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20130517/utaddress-251)
[ 2.876697] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.908262] usb 4-1: new high-speed USB device number 2 using ehci-pci
[ 2.913682] [drm] Memory usable by graphics device = 2048M
[ 2.913687] checking generic (e0000000 7f0000) vs hw (e0000000 10000000)
[ 2.913688] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 2.913702] Console: switching to colour dummy device 80x25
[ 2.913836] i915 0000:00:02.0: setting latency timer to 64
[ 2.948473] i915 0000:00:02.0: irq 47 for MSI/MSI-X
[ 2.948482] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 2.948483] [drm] Driver supports precise vblank timestamp query.
[ 2.948547] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 3.032964] hub 4-1:1.0: USB hub found
[ 3.033016] hub 4-1:1.0: 8 ports detected
[ 3.038244] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3.169633] e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
[ 3.221450] [drm] GMBUS [i915 gmbus vga] timed out, falling back to bit banging on pin 2
[ 3.237256] fbcon: inteldrmfb (fb0) is primary device
[ 3.271526] e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
[ 3.271623] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.491212] Switched to clocksource tsc
[ 4.027317] psmouse serio2: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x126c00, board id: 2439, fw id: 1215751
[ 4.066270] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input7
[ 4.477837] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 4.967580] Console: switching to colour frame buffer device 240x67
[ 4.977758] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 4.977761] i915 0000:00:02.0: registered panic notifier
[ 4.978457] acpi device:45: registered as cooling_device8
[ 4.978479] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.978579] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input8
[ 4.978690] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.978877] snd_hda_intel 0000:00:1b.0: irq 48 for MSI/MSI-X
[ 4.979210] snd_hda_intel 0000:00:03.0: irq 49 for MSI/MSI-X
[ 4.989927] hda_codec: invalid CONNECT_LIST verb 5[1]:0
[ 4.989974] hda_codec: invalid CONNECT_LIST verb 6[1]:0
[ 4.990029] hda_codec: invalid CONNECT_LIST verb 7[1]:0
[ 4.991935] input: HDA Intel MID HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
[ 4.992031] input: HDA Intel MID HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input10
[ 4.992087] input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input11
[ 4.994100] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input12
[ 4.994171] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input13
[ 6.977361] wlan0: authenticate with 00:1d:45:cd:c1:c2
[ 6.987213] wlan0: send auth to 00:1d:45:cd:c1:c2 (try 1/3)
[ 6.988904] wlan0: authenticated
[ 6.989040] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 6.989044] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 6.989046] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 6.990123] wlan0: associate with 00:1d:45:cd:c1:c2 (try 1/3)
[ 6.993437] wlan0: RX AssocResp from 00:1d:45:cd:c1:c2 (capab=0x431 status=0 aid=9)
[ 6.993577] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 6.993624] wlan0: associated
[ 6.998736] wlan0: deauthenticating from 00:1d:45:cd:c1:c2 by local choice (reason=1)
[ 7.002835] cfg80211: Calling CRDA for country: US
[ 24.197672] wlan0: authenticate with 00:1d:45:cd:c1:c2
[ 24.207666] wlan0: send auth to 00:1d:45:cd:c1:c2 (try 1/3)
[ 24.209338] wlan0: authenticated
[ 24.209468] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 24.209472] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 24.209474] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 24.210593] wlan0: associate with 00:1d:45:cd:c1:c2 (try 1/3)
[ 24.213338] wlan0: RX AssocResp from 00:1d:45:cd:c1:c2 (capab=0x31 status=0 aid=9)
[ 24.213481] wlan0: associated
[ 24.221396] wlan0: deauthenticating from 00:1d:45:cd:c1:c2 by local choice (reason=1)
[ 24.225880] cfg80211: Calling CRDA to update world regulatory domain
[ 50.045002] wlan0: authenticate with 00:19:30:6b:1b:a2
[ 50.054957] wlan0: send auth to 00:19:30:6b:1b:a2 (try 1/3)
[ 50.056639] wlan0: authenticated
[ 50.056775] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 50.056779] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 50.056781] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 50.057899] wlan0: associate with 00:19:30:6b:1b:a2 (try 1/3)
[ 50.061270] wlan0: RX AssocResp from 00:19:30:6b:1b:a2 (capab=0x431 status=0 aid=89)
[ 50.061426] wlan0: associated
[ 50.073874] wlan0: deauthenticating from 00:19:30:6b:1b:a2 by local choice (reason=1)
[ 50.078661] cfg80211: Calling CRDA to update world regulatory domain
[ 75.892318] wlan0: authenticate with 00:1d:45:cd:c1:c2
[ 75.902267] wlan0: send auth to 00:1d:45:cd:c1:c2 (try 1/3)
[ 75.904108] wlan0: authenticated
[ 75.904254] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 75.904256] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 75.904257] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 75.905145] wlan0: associate with 00:1d:45:cd:c1:c2 (try 1/3)
[ 75.908344] wlan0: RX AssocResp from 00:1d:45:cd:c1:c2 (capab=0x401 status=17 aid=0)
[ 75.908348] wlan0: 00:1d:45:cd:c1:c2 denied association (code=17)
[ 75.918844] wlan0: deauthenticating from 00:1d:45:cd:c1:c2 by local choice (reason=3)
[ 86.045293] wlan0: authenticate with 00:19:30:6b:1b:52
[ 86.059226] wlan0: send auth to 00:19:30:6b:1b:52 (try 1/3)
[ 86.061328] wlan0: authenticated
[ 86.061475] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 86.061477] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 86.061478] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 86.064853] wlan0: associate with 00:19:30:6b:1b:52 (try 1/3)
[ 86.169949] wlan0: associate with 00:19:30:6b:1b:52 (try 2/3)
[ 86.179194] wlan0: RX AssocResp from 00:19:30:6b:1b:52 (capab=0x431 status=0 aid=22)
[ 86.179323] wlan0: associated
[ 89.123073] wlan0: deauthenticated from 00:19:30:6b:1b:52 (Reason: 4)
[ 89.147287] cfg80211: Calling CRDA for country: US
[ 105.770381] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 105.770386] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO
[ 105.770418] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 114.898216] wlan0: authenticate with 00:19:30:6b:1b:a2
[ 114.912130] wlan0: send auth to 00:19:30:6b:1b:a2 (try 1/3)
[ 114.914102] wlan0: authenticated
[ 114.914235] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 114.914239] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 114.914241] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 114.914348] wlan0: associate with 00:19:30:6b:1b:a2 (try 1/3)
[ 114.916916] wlan0: RX AssocResp from 00:19:30:6b:1b:a2 (capab=0x401 status=17 aid=0)
[ 114.916920] wlan0: 00:19:30:6b:1b:a2 denied association (code=17)
[ 114.937999] wlan0: deauthenticating from 00:19:30:6b:1b:a2 by local choice (reason=3)
[ 125.064495] wlan0: authenticate with 00:19:30:6b:1b:52
[ 125.078431] wlan0: send auth to 00:19:30:6b:1b:52 (try 1/3)
[ 125.081945] wlan0: authenticated
[ 125.082083] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 125.082094] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 125.082095] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 125.084061] wlan0: associate with 00:19:30:6b:1b:52 (try 1/3)
[ 125.098558] wlan0: RX AssocResp from 00:19:30:6b:1b:52 (capab=0x431 status=0 aid=22)
[ 125.098683] wlan0: associated
[ 127.937457] wlan0: deauthenticated from 00:19:30:6b:1b:52 (Reason: 4)
[ 127.959914] cfg80211: Calling CRDA to update world regulatory domain
Edit: I ended up solving my problem -- the issue I was running into was that ath9k was baked into my initrd without nohwcrypt=1. I opted to `mkinitcpio` again without MODULES='ath9k' -- alternatively, you could add a modprobe.d file to FILES= to get it to work, but I just figured this is simpler.
Last edited by Pobega (2013-10-02 03:57:27) -
Troubles with installing quicktime : macbook being h e ll !
Hello everybody,
first, i would like to apologize for my bad english, i'm french and i don't speak very well english.
Il will try to explain my trouble :
I'm the owner of a macbook ( MAC OS 10.6 ) for more than four years.
I try to upgrade Quicktime Player, because when i tried to watch movies with it, i got a error message : " You have to upgrade Quick Time, etc " and i folow the link :http://www.apple.com/quicktime/download/ and i downloaded it and installed on my computer. It asked me to reboot. I did it. And H e ll was coming on my poor Macbook :
- about five minutes to boot,
- Icons on the desk don't appear
- impossible to launch any process like i-tunes, firefox, teamspeack...
- options of the high menu are disables ( finder, time, wi-fi, bluetooth)
- i can't shut off the macbook normally. I have to force it.
I take a (bad) picture :
I tried to press APPLE-S at the start and used the fsck -fy function, i get :
FILE SYSTEM WAS MODIFIED
After three others trys, i get :
" The volume Macintosh HD appears to be OK. "
I type : " reboot " but it's the same like usual = doesn't work.
I tried to press APPLE shift at the start, nothing changes.
My DVD-reader is broken, i can't ' format ' or reaload Mac OS 10.6, so i'm asking for a solution.
I thank you for any help you could bring to me, and i apologize for my bad english,
cordialy,
Baacha.Hi,
i can go to the Disk Utility with hard freeze ( and some icons don't appear ) but when i double click on Disk Utility, nothing happens. -
Help, I'm having trouble with installing my new Creative Zen MicroPhoto..can someone help
Okay, I bought my MicroPhoto about a week ago and now I've been making atempts to install it so I can listen to some music. YAY. Well, When I placed the installation CD in that I was told to put in first, my computer wouldn't read it. So, I tried downloading the stuff (aka: the programs that's needed to run with a Windows XP with Service Pack 2) but I got this instead: "Your Player is not Connected, please connect your player." (this is for the firm) Okay, My player, the MicroPhoto, is already connected to my computer and the computer knows its there. When I tried to install the other programs that could be download with Windows XP, I got messages referring that the Windows 2 Service pack was involed with it. My question is...how can I get my MircoPhoto to work on this computer?
I would advise to still double check all your WEB router settings and to make sure it's putting out maximum output and device/signal separation.
Also, try go into all your browser apps on your iPhone (safari/chrome etc.) and clear all cache/cookie/passwords/history
I have iPhone 4S 6.0.1 and never had wifi issues, but I also had just switched ISP's, and went through all of the above. So not sure if I solved the issue before it even came up. I seem to be getting pretty good speeds and very steady connection. -
Trouble with installing/uninstalling illustrator and cloud manager
I first was having trouble installing adobe illustrator CC trial. It kept having errors. I did what they suggested and now I cannot even install the creative manager. Now it will not even allow me to uninstall adobe illustrator (even though it never fully downloaded to begin with, it still shows up on control panel) I ran the adobe cloud cleaner multiple times, trying different settings and some of the times it says it had an error. Adobe illustrator doesn't even appear to exist on my computer other than being listed in control panel, yet I still can't get rid of it. I've restarted my computer. I've even tried downloading the trial from a different site and it would not work. Can anyone please help me?
Thank you so much!There's a dedicated forum for installing. They might be able to help you better there:
http://forums.adobe.com/community/download_install_setup -
Having trouble with installing updates
Hello,
I am having trouble installing updates. I checked the windowsupdate.log file and I see:
2015-03-13
11:52:43:075 956
680 Agent
* Criteria = "(DeploymentAction=* AND Type='Software') OR (DeploymentAction=* AND Type='Driver')"
In reading others' posts, I noticed in their logs contain "DeploymentAction=Install" .. could this potentially be the issue why it will not install the update? If so, where does this get set at so I can modify it? I looked around
but was not able to find this setting.
Thanks for the help!Hello,
Here is what I see in the logs. Can you please take a look and see if anything stands out? There are a lot of errors/failures/warnings in the
WindowsUpdate.log. Please look at the last 4 lines of this log listed below -- looks like it is looking for approval or "WARNING: There are no approved updates to install". Where is this coming from? Is this
why the updates do not get installed? Thanks for any help in reviewing these logs. Thanks.
<looks good>Scanagent.log = No errors/fail/warnings
<![LOG[ScanJob({70E7DB5B-44CF-4BC0-B73F-B89A9AB557BF}): CScanJob::OnScanComplete - Scan completed successfully, ScanType=1]LOG]!><time="23:48:18.177+300" date="03-02-2015" component="ScanAgent"
context="" type="1" thread="2876" file="utils.cpp:477">
WUAHandler.log =
<![LOG[Unable to read existing resultant WUA policy. Error = 0x80070002.]LOG]!><time="05:57:24.588+300" date="02-26-2015" component="WUAHandler" context="" type="2"
thread="4148" file="sourcemanager.cpp:920">
<![LOG[Search Criteria is (DeploymentAction=* AND Type='Software') OR (DeploymentAction=* AND Type='Driver')]LOG]!><time="02:26:17.774+240" date="03-11-2015" component="WUAHandler"
context="" type="1" thread="4240" file="cwuahandler.cpp:2916">
<![LOG[Async searching of updates using WUAgent started.]LOG]!><time="02:26:17.774+240" date="03-11-2015" component="WUAHandler" context="" type="1" thread="4240"
file="cwuahandler.cpp:579">
<![LOG[Async searching completed.]LOG]!><time="02:26:24.339+240" date="03-11-2015" component="WUAHandler" context="" type="1" thread="4048" file="cwuahandler.cpp:2068">
<![LOG[Successfully completed scan.]LOG]!><time="02:26:25.651+240" date="03-11-2015" component="WUAHandler" context="" type="1" thread="4240" file="cwuahandler.cpp:3557">
-------------------------------------------------------------------------------------------------------------------------WindowsUpdate.log
= A lot of errors here --
2015-03-11
05:55:59:437 956
1194 AU
WARNING: Failed to get Wu Exemption info from NLM, assuming not exempt, error = 0x80240037
2015-03-11
05:55:59:437 956
1194 AU
WARNING: Failed to get Network Cost info from NLM, assuming network is NOT metered, error = 0x80240037
2015-03-11
05:57:22:655 956
144c EP
FATAL: EP: Failed to obtain element node, error = 0x80245002
2015-03-11
05:57:22:780 956
144c EP
FATAL: Failed to obtain plugin interfaces using CLSID 7D5F3CBA-03DB-4BE5-B4B3-6DBED19A6833, error = 0x8024000E
2015-03-11
05:57:22:821 956
144c Agent
WARNING: WU client failed Searching for update with error 0x8024000e
2015-03-11
05:55:59:296 956
1194 Agent
WARNING: SleepStudyTracker: Machine is non-AOAC. Sleep study tracker disabled.
2015-03-11
05:55:59:358 956
1194 Misc
WARNING: Network Cost is assumed to be not supported as something failed with trying to get handles to wcmapi.dll
2015-03-11
05:57:22:749 956
144c Agent
WARNING: Failed to obtain the authorization cab URL for service 855e8a7c-ecb4-4ca3-b045-1dfa50104289, hr=0
2015-03-11
05:57:22:811 956
144c PT
WARNING: PTError: 0x8024000e
2015-03-11
05:57:22:811 956
144c PT
WARNING: Initialization failed for Protocol Talker Context: 0x8024000e
2015-03-11
05:57:22:811 956
144c Agent
* WARNING: Exit code = 0x8024000E
2015-03-11
06:21:56:594 968
e8c Report
WARNING: CSerializationHelper:: InitSerialize failed : 0x80070002
2015-03-16
04:14:17:850 968
1660 EP
FATAL: Failed to obtain 9482F4B4-E343-43B6-B170-9A65BC822C77 redir SecondaryServiceAuth URL, error = 0x80245002
2015-03-16
04:14:17:850 968
1660 Agent
WARNING: Failed to obtain the authorization cab URL for service 855e8a7c-ecb4-4ca3-b045-1dfa50104289, hr=0
2015-03-11
05:57:23:321 956
17f8 Report
REPORT EVENT: {D462FFC9-CF2C-4EB8-91DC-4EB946A903A1}
2015-03-11 05:57:22:811-0400 1
148 [AGENT_DETECTION_FAILED]
101 {00000000-0000-0000-0000-000000000000}
0
8024000e
AutomaticUpdates
Failure Software Synchronization
Windows Update Client failed to detect with error 0x8024000e.
<as seen earlier in the logs>2015-03-11
02:26:24:027 956
1274 Report
REPORT EVENT: {F5A3CD05-8B66-4806-BAF7-48AD2E8012E8}
2015-03-11 02:26:24:027-0400 1
147 [AGENT_DETECTION_FINISHED]
101 {00000000-0000-0000-0000-000000000000}
0
0
CcmExec
Success
Software Synchronization
Windows Update Client successfully detected 40 updates.
2015-03-18
06:40:25:397 968
5fc AU
## START ## AU: Install updates
2015-03-18
06:40:25:397 968
5fc AU
2015-03-18
06:40:25:397 968
5fc AU
# Initiating scheduled install
2015-03-18
06:40:25:428 968
5fc AU
WARNING: There are no approved updates to install -
[SOLVED] Trouble With Age of Empires 2 / Conquerors in Wine
As the title indicates I'm trying to install and run Age of Empires 2 and the expansion Conquerors, with Wine. Looks like it should work: http://appdb.winehq.org/objectManager.p … n&iId=4184
So first I installed wine and the video driver like this...
pacman -Sy wine wine_gecko lib32-intel-dri
Then, for each iso I mounted it to a new folder and ran the install file on the image with wine. Here's how I mounted each iso...
mount -o loop aoe.iso /mnt/mydisk
Installation of both AOE2 and the Conquerors seemed to work fine. But then when I attempted to play the game from the installation menu, popping up a "Program Error" that "the program age2_x1.exe has encountered a serious problem and needs to close." If I run AOCSETUP.EXE from the mounted iso right now, the main menu (with options "Play", "Add/Remove", "Web Connection", and "Register online") shows up but clicking "play" results in the same error. I've tried removing the dpwsockx.dll file that WineHQ mentions but it makes no difference.
I also tried loading wine with the option for Intel graphics, but had the same error as well as the following error in the console...
[karam@nikolai mydisk]$ env LIBGL_DRIVERS_PATH=/usr/lib32/xorg/modules/dri wine AOCSETUP.EXE
err:module:load_builtin_dll failed to load .so lib for builtin L"winemp3.acm": libmpg123.so.0: cannot open shared object file: No such file or directory
err:module:load_builtin_dll failed to load .so lib for builtin L"winemp3.acm": libmpg123.so.0: cannot open shared object file: No such file or directory
[karam@nikolai mydisk]$ fixme:alsa:AudioClient_GetMixFormat Don't know what to do with 10000 channels, pretending there's only 2 channels
fixme:alsa:AudioClient_GetMixFormat Don't know what to do with 10000 channels, pretending there's only 2 channels
fixme:alsa:AudioClient_GetMixFormat Don't know what to do with 10000 channels, pretending there's only 2 channels
fixme:alsa:AudioClient_GetMixFormat Don't know what to do with 10000 channels, pretending there's only 2 channels
fixme:alsa:AudioClient_GetMixFormat Don't know what to do with 10000 channels, pretending there's only 2 channels
fixme:alsa:AudioClient_GetMixFormat Don't know what to do with 10000 channels, pretending there's only 2 channels
wine: Unhandled page fault on write access to 0xcf8672fe at address 0x40d774 (thread 003b), starting debugger...
[karam@nikolai mydisk]$
Does anyone have any ideas?...
Last edited by tony5429 (2011-11-09 04:43:40)Are you on x86_64? Might wanna run WINEARCH=win32 winecfg (wiki entry for winearch). WINE works with the video drivers that you use for xorg not sure if you really need to specify that intel-dri driver.
Another thing that works quite well for me is make sure the current working directory is the game directory, then use wine to run the .exe. I recently installed Anachronox and if I try to launch it from outside the game directory i get missing dll errors also, even though the dlls are present in the game directory.
Also did you follow the following How-To steps on the WINE game page?
The game must be set to Windows 2000 compatibility. (seems to play equally well with XP mode too, though.)
This game requires a NoCD patch to run. (you can play using aocsetup.exe from the cd, if you can’t afford to NoCD)
If the game wont start (and wine hasn’t hang up(pkill wine && pkill exe)), either remove dpwsockx.dll from your system32 folder or follow the steps for multi-player below. ¹
Last edited by KingX (2011-11-01 08:25:10)
Maybe you are looking for
-
Mac book air connected to a dell screen shows only the background
Why can I only see the background on my Dell monitor which is connected via the thunderbolt connection using a display cable please?
-
Connect two U2515H displays to Vostro 460.
I recently aquired two of Dell's 25" U2515H displays. I would like to know how I would go about connecting those up to on of Dell's Vostro 460 mini towers (from 2011, i5 3.1 GHz, 4GB RAM, onboard HDMI). What, if any, (2x DP) GPU expansion card will
-
how can i use instant messaging with other iphone just like blackberry messaging
-
Upgraded (6.0.6) iPhoto will not recognise music purchased from ITune
I downloaded the iPhoto 6.0.6 update and the iTunes 7.1.1 update, and now when I try to add any of the songs from my iTunes library which I have purchased from the iTunes store to one of my Iphoto slideshows, it says that my computer is not authorise
-
ICS via PC Companion is Now Working!
Finally ... No errors or weird messages: Keeping my fingers crossed right now as my phone is powering back up. Bob H ST18a Ray