[Solved] Trouble with WPA/WPA2 and wireless connections (ath9k)
Hi, I'm having some issues with my Arch install. Right now I'm posting this from Windows so I don't have precise logs, but I mostly remember the issue so bare with me.
I'm using ath9k with my Bigfoot Killer 1202 card (not sure what the exact model is), and I can't connect to my university's WPA/WPA2 access point. Using wpa_supplicant I get the error "4-way handshake failed - pre-shared key may be incorrect".
So after some digging I found that I can get it to authenticate with nohwcrypt=1, but when I rmmod ath9k && modprobe ath9k nohwcrypt=1 it enumerates itself as wlan0 (instead of wlp3s0, which is what I get from booting up).
Then I made the file /etc/modprobe.d/ath9k with the contents "options ath9k nohwcrypt=1" but it seems to still not want to connect until I rmmod && modprobe manually.
Can someone point me in the right direction on how to fix this issue? I haven't used Arch in a few years and a lot of things have changed, and so far it seems nothing works as I expect it to. Also, how do I get my wifi card to enumerate as the same device no matter when I load ath9k? I don't care if it's called wlan0 or wlp3s0, I just want it to stay the same.
Edit: Additional Info
lspci
03:00.0 Network controller: Qualcomm Atheros AR9462 Wireless Network Adapter (rev 01)
cat /sys/module/ath9k/parameters/nohwcrypt
[root@huxley pobegam]# cat /sys/module/ath9k/parameters/nohwcrypt
0
(so I guess it isn't loading from ath9k.conf on boot after all?)
wpa_supplicant output
<3>CTRL-EVENT-SCAN-RESULTS
<3>WPS-AP-AVAILABLE
<3>CTRL-EVENT-SCAN-RESULTS
<3>WPS-AP-AVAILABLE
<3>CTRL-EVENT-SSID-REENABLED id=0 ssid="Student"
<3>Trying to associate with 00:19:30:6b:1b:a2 (SSID='Student' freq=2412 MHz)
<3>Association request to the driver failed
<3>Associated with 00:19:30:6b:1b:a2
<4>WPA: Failed to set PTK to the driver (alg=2 keylen=32 bssid=00:19:30:6b:1b:a2)
<3>CTRL-EVENT-DISCONNECTED bssid=00:19:30:6b:1b:a2 reason=1 locally_generated=1
<3>WPA: 4-Way Handshake failed - pre-shared key may be incorrect
<3>CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="Student" auth_failures=2 duration=20
<3>CTRL-EVENT-SCAN-RESULTS
<3>WPS-AP-AVAILABLE
wpa_supplicant configuration file
[root@huxley wpa_supplicant]# cat sunyit.conf
ctrl_interface=/var/run/wpa_supplicant
update_config=1
network={
scan_ssid=1
ssid="Student"
proto=WPA
key_mgmt=WPA-PSK
pairwise=TKIP
group=TKIP
priority=1
psk="Wireless@SUNYIT"
Last edited by Pobega (2013-10-02 03:55:51)
Update: It seems to work ONLY when I rmmod && modprobe; if I force nohwcrypt=1 at boot it doesn't seem to work. Seems kind of odd... Wonder if this is a kernel issue?
Edit: Also updated with dmesg (because I'm an idiot and forgot to include it)
[ 2.802118] hub 3-1:1.0: USB hub found
[ 2.802210] hub 3-1:1.0: 6 ports detected
[ 2.876377] e1000e 0000:00:19.0 eth0: registered PHC clock
[ 2.876380] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:90:f5:ea:54:ff
[ 2.876382] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 2.876418] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF
[ 2.876688] ACPI Warning: 0x000000000000f040-0x000000000000f05f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20130517/utaddress-251)
[ 2.876697] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.908262] usb 4-1: new high-speed USB device number 2 using ehci-pci
[ 2.913682] [drm] Memory usable by graphics device = 2048M
[ 2.913687] checking generic (e0000000 7f0000) vs hw (e0000000 10000000)
[ 2.913688] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 2.913702] Console: switching to colour dummy device 80x25
[ 2.913836] i915 0000:00:02.0: setting latency timer to 64
[ 2.948473] i915 0000:00:02.0: irq 47 for MSI/MSI-X
[ 2.948482] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 2.948483] [drm] Driver supports precise vblank timestamp query.
[ 2.948547] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 3.032964] hub 4-1:1.0: USB hub found
[ 3.033016] hub 4-1:1.0: 8 ports detected
[ 3.038244] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3.169633] e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
[ 3.221450] [drm] GMBUS [i915 gmbus vga] timed out, falling back to bit banging on pin 2
[ 3.237256] fbcon: inteldrmfb (fb0) is primary device
[ 3.271526] e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
[ 3.271623] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.491212] Switched to clocksource tsc
[ 4.027317] psmouse serio2: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x126c00, board id: 2439, fw id: 1215751
[ 4.066270] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input7
[ 4.477837] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 4.967580] Console: switching to colour frame buffer device 240x67
[ 4.977758] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 4.977761] i915 0000:00:02.0: registered panic notifier
[ 4.978457] acpi device:45: registered as cooling_device8
[ 4.978479] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.978579] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input8
[ 4.978690] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.978877] snd_hda_intel 0000:00:1b.0: irq 48 for MSI/MSI-X
[ 4.979210] snd_hda_intel 0000:00:03.0: irq 49 for MSI/MSI-X
[ 4.989927] hda_codec: invalid CONNECT_LIST verb 5[1]:0
[ 4.989974] hda_codec: invalid CONNECT_LIST verb 6[1]:0
[ 4.990029] hda_codec: invalid CONNECT_LIST verb 7[1]:0
[ 4.991935] input: HDA Intel MID HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
[ 4.992031] input: HDA Intel MID HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input10
[ 4.992087] input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input11
[ 4.994100] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input12
[ 4.994171] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input13
[ 6.977361] wlan0: authenticate with 00:1d:45:cd:c1:c2
[ 6.987213] wlan0: send auth to 00:1d:45:cd:c1:c2 (try 1/3)
[ 6.988904] wlan0: authenticated
[ 6.989040] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 6.989044] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 6.989046] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 6.990123] wlan0: associate with 00:1d:45:cd:c1:c2 (try 1/3)
[ 6.993437] wlan0: RX AssocResp from 00:1d:45:cd:c1:c2 (capab=0x431 status=0 aid=9)
[ 6.993577] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 6.993624] wlan0: associated
[ 6.998736] wlan0: deauthenticating from 00:1d:45:cd:c1:c2 by local choice (reason=1)
[ 7.002835] cfg80211: Calling CRDA for country: US
[ 24.197672] wlan0: authenticate with 00:1d:45:cd:c1:c2
[ 24.207666] wlan0: send auth to 00:1d:45:cd:c1:c2 (try 1/3)
[ 24.209338] wlan0: authenticated
[ 24.209468] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 24.209472] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 24.209474] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 24.210593] wlan0: associate with 00:1d:45:cd:c1:c2 (try 1/3)
[ 24.213338] wlan0: RX AssocResp from 00:1d:45:cd:c1:c2 (capab=0x31 status=0 aid=9)
[ 24.213481] wlan0: associated
[ 24.221396] wlan0: deauthenticating from 00:1d:45:cd:c1:c2 by local choice (reason=1)
[ 24.225880] cfg80211: Calling CRDA to update world regulatory domain
[ 50.045002] wlan0: authenticate with 00:19:30:6b:1b:a2
[ 50.054957] wlan0: send auth to 00:19:30:6b:1b:a2 (try 1/3)
[ 50.056639] wlan0: authenticated
[ 50.056775] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 50.056779] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 50.056781] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 50.057899] wlan0: associate with 00:19:30:6b:1b:a2 (try 1/3)
[ 50.061270] wlan0: RX AssocResp from 00:19:30:6b:1b:a2 (capab=0x431 status=0 aid=89)
[ 50.061426] wlan0: associated
[ 50.073874] wlan0: deauthenticating from 00:19:30:6b:1b:a2 by local choice (reason=1)
[ 50.078661] cfg80211: Calling CRDA to update world regulatory domain
[ 75.892318] wlan0: authenticate with 00:1d:45:cd:c1:c2
[ 75.902267] wlan0: send auth to 00:1d:45:cd:c1:c2 (try 1/3)
[ 75.904108] wlan0: authenticated
[ 75.904254] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 75.904256] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 75.904257] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 75.905145] wlan0: associate with 00:1d:45:cd:c1:c2 (try 1/3)
[ 75.908344] wlan0: RX AssocResp from 00:1d:45:cd:c1:c2 (capab=0x401 status=17 aid=0)
[ 75.908348] wlan0: 00:1d:45:cd:c1:c2 denied association (code=17)
[ 75.918844] wlan0: deauthenticating from 00:1d:45:cd:c1:c2 by local choice (reason=3)
[ 86.045293] wlan0: authenticate with 00:19:30:6b:1b:52
[ 86.059226] wlan0: send auth to 00:19:30:6b:1b:52 (try 1/3)
[ 86.061328] wlan0: authenticated
[ 86.061475] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 86.061477] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 86.061478] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 86.064853] wlan0: associate with 00:19:30:6b:1b:52 (try 1/3)
[ 86.169949] wlan0: associate with 00:19:30:6b:1b:52 (try 2/3)
[ 86.179194] wlan0: RX AssocResp from 00:19:30:6b:1b:52 (capab=0x431 status=0 aid=22)
[ 86.179323] wlan0: associated
[ 89.123073] wlan0: deauthenticated from 00:19:30:6b:1b:52 (Reason: 4)
[ 89.147287] cfg80211: Calling CRDA for country: US
[ 105.770381] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 105.770386] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO
[ 105.770418] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 114.898216] wlan0: authenticate with 00:19:30:6b:1b:a2
[ 114.912130] wlan0: send auth to 00:19:30:6b:1b:a2 (try 1/3)
[ 114.914102] wlan0: authenticated
[ 114.914235] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 114.914239] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 114.914241] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 114.914348] wlan0: associate with 00:19:30:6b:1b:a2 (try 1/3)
[ 114.916916] wlan0: RX AssocResp from 00:19:30:6b:1b:a2 (capab=0x401 status=17 aid=0)
[ 114.916920] wlan0: 00:19:30:6b:1b:a2 denied association (code=17)
[ 114.937999] wlan0: deauthenticating from 00:19:30:6b:1b:a2 by local choice (reason=3)
[ 125.064495] wlan0: authenticate with 00:19:30:6b:1b:52
[ 125.078431] wlan0: send auth to 00:19:30:6b:1b:52 (try 1/3)
[ 125.081945] wlan0: authenticated
[ 125.082083] ath9k 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 125.082094] ath9k 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 125.082095] ath9k 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 125.084061] wlan0: associate with 00:19:30:6b:1b:52 (try 1/3)
[ 125.098558] wlan0: RX AssocResp from 00:19:30:6b:1b:52 (capab=0x431 status=0 aid=22)
[ 125.098683] wlan0: associated
[ 127.937457] wlan0: deauthenticated from 00:19:30:6b:1b:52 (Reason: 4)
[ 127.959914] cfg80211: Calling CRDA to update world regulatory domain
Edit: I ended up solving my problem -- the issue I was running into was that ath9k was baked into my initrd without nohwcrypt=1. I opted to `mkinitcpio` again without MODULES='ath9k' -- alternatively, you could add a modprobe.d file to FILES= to get it to work, but I just figured this is simpler.
Last edited by Pobega (2013-10-02 03:57:27)
Similar Messages
-
WPA/WPA2 secured wireless connection fails for two minurtes for every hour of use.
Hello.
I have a brand new ThinkPad T500 2055-A16 with Windows Vista Business. I have a WiFi connection problem. It is not a signal strength problem, as it doesn't work even if I place the computer right next to the access point with no other wireless equipment near by.
None of my other computers experience this problem. I even bought another ThinkPad T500 2055-A16 at the same time as this one, and that does not have the problem either. The problem is when I connect to a network using WPA2-PSK or WPA-PSK. The connection works fine for half an hour, an hour or two hours, but then without warning, the connection is lost and it is not possible to reconnect for half a minute, a minute or two minutes. The exact times vary. When I switch the network to use WEP or no encryption, everything works fine. But I don't like to use no encryption and I cannot use WEP because I have other computers in my home which does not support WEP.
I had this problem right from the beginning the first time I used the computer. I have tried many things like disabling power management or IPv6 and other things suggested by my ISP, but it did not change anything, so I switched them back to their default value. I have also tried to update the driver for the Intel(R) WiFi Link 5100 AGN card, but that didn't help the problem. The problem became slightly less annoying when I uninstalled Access Connections, because Vista would then reconnect as soon as it could, whereas I in Access Connections would have to continuously press the connect button until it succeeded. But the problem is still a real pain.
Some pieces from the Windows Event Viewer, which I think looks interesting (these occur regularly at exactly the same timestamps as when the connection is lost):
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Fail
0x00048005 and 0x0003800b
Result of diagnosis: Problem found
Issue referred to: L2Sec Helper Class
I also see the following message on my access point's log, which also occur at exactly the times when the connection is lost:
1x:00216b4d7ee6:logout
(The number match the MAC address of my computer)
The only other message which is logged on my Access Point when all log options are enabled is "Time initialized by NTP server".
How can I solve this problem so that I can have undisrupted wireless Internet access?Edit: Actually my other ThinkPad T500 2055-A16 also fails in the same way, but my ThinkPad SL500 2746-9BG and my Medion laptops works fine, also running Vista.
-
Trouble with Qwest DSL and wireless router
Just got Qwest DSL yesterday. Connected the Actiontec M1000 modem directly to our IMac and things worked fine. Unfortunately, our office doesn't have a phone line and the permanent home of the modem is going to be elsewhere in the house. I tried to connect our D-Link wireless router WBR-2310 Rangebooster G to the Actiontec, phone jack--ethernet cable---actiontec---ethernet cable---d-link wan jack. Airport can "see" the wireless network we had setup before we switched to qwest dsl, but cannot connect to the internet.
I'm assuming there is communication problem between the dsl modem and wireless router.
How should my network settings be changed? Do I need to reconfigure the modem, or the wireless router, or both?{quote}
Now, I must say that the 3mbps download speed I'm apparently paying for has never been achieved. The fastest I got was 1.4mbps when hardwired. Now with the wireless I'm only around 750 kbps. I'm only twenty feet away and one wall from the router. Any suggestions on increasing this performance?
Very few sites can actually send you 3mb/s. You can test your connection here:
http://www.speakeasy.net/speedtest/
or here:
http://speedtest.net/
If your speeds don't seem to be inline then you will have to deal with your broadband provider.
At 54mb/s your wireless is not the bottleneck, the internet is.
I'm getting 6mb DSL and it tests perfect, but I wanted the extra speed because I'm running 6 or 8 machines online at all times, and you usually get a faster upload speed with the deal. This can be very important for sharing files and sending emails with attachments, etc. -
Problem with connetction to wrt54g2 via wireless connection with WPA/WPA2 & wireless MAC filter
Hello,
I'm Alexey from Novosibirsk, Russia.
I have a problem with connection to wrt54g2 from my DELL D630 notebook via wireless connection. When I setup WPA/WPA2 in wireless security and wireless MAC filter I can't connect from notebook to WRT - in Windows I see that dynamic IP address from WRT is not assigned. When I switch off security mode to disable always OK, but I need a wireless security between DELL and WRT.
Connection via cable Ethernet port is OK.
Can You help me?Have you tried the different laptop...?
Download 1.71 MB the firmware for WRT54G2 v1 and reflash the router's firmware.After reflashing/upgrading the router's firmware,reset the router for 30 seconds and reconfigure the router from scratch. -
I have a Mac, IPad, I phones, and 2 Windows Vista Pcs and I'm having trouble with the Windows Laptop staying connected. I have to re-boot after an extended period of time please help. Thanks!
I have a Mac, IPad, I phones, and 2 Windows Vista Pcs and I'm having trouble with the Windows Laptop staying connected. I have to re-boot after an extended period of time please help. Thanks!
-
I am having trouble with iMessages. I cannot connect iMessage from my iPhone to my macbook air. This happened after I changed my apple id and keychain password last night.
Hi geraldinefromjersey city,
I'm sorry to hear you are having issues with Messages. If you are having issues linking your Messages accounts between your iPhone and MacBook Air, you may find the information and troubleshooting steps outlined in the following articles helpful:
iOS and OS X: Link your phone number and Apple ID for use with FaceTime and iMessage - Apple Support
Connect your iPhone, iPad, iPod touch, and Mac using Continuity - Apple Support
Regards,
- Brenden -
I have an existing new belkin modem router which works fine with quiet a few wired and wireless products in my house. My question is if i buy a time capsule can i put it in another room and wirelessly connect it to the belkin modem router, I would then just like my macbook pro and (imac future purchase) to wirelessly back up to it???????????
Your will need to perform a Factory Default Reset on the TIme Capsule to clear out the current network settings and then reconfigure it to "join" your wireless network using the AirPort Utility setup application.
To perform the Factory Default Reset on the Time Capsule....
Pull the power cord from the back of the device
Wait a few moments
Hold in the reset button on the back of the Time Capsule and keep holding it an additional 8-10 seconds while you simultaneously plug the power cord back in to the Time Capsule
Release the reset button after the hold period and allow 25-30 seconds for the Time Capsule to restart to a slow, blinking amber light
On your Mac.....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click Continue
Follow the guided setup and choose the "join" option when it appears duriing the setup
You will need to know the exact type of wireless security that the Belkin router is using to enter this information during the setup of the Belkin. Otherwise, the Time Capsule cannot join the network, and you will receive an error message after the configuration process. -
E70 doesn't work with WPA/WPA2!
Hello, ppl!
Does anybody know if there is any chance that E70 will work with WPA/WPA2 encryption? Found it is not working with my home router configured to WPA but works with WEP. However WEP isn't strong protection and I'd prefer WPA. I just took phone to see it's capabilities before buying but lack of WPA would stop me from purchase - WM devices never had such trouble
'd like to hear from someone who do really know if this device will ever work with WPA and maybe it could do now.
PS. have installed latest firmwares to the router and mobile phone.ST.x wrote:
Maos wrote:
iphitus wrote:Sorry, I upped a new netcfg but forgot to run the update scripts on archlinux.org.... done now, the package is up.
I am very impressed of what all of you are doing but out of curiosity I ask in the most humble way when the x86_64 package will be up?
ABS
Doh! Don't know why I didn't think of that... -
How to set up WRT54GS so the wired and wireless connections both work?
I have a DSL line in to a Motorola modem.
The modem is connected to the WRT54GS with an ethernet cable.
When I connect my computers directly into the WRT54GS with an ethernet cable (there are four connection spots at the back of the box), I cannot go to the internet. I have 3 computers plugged in, but none of them connect via Ethernet..
Is there a setting on the router so that I can use the router for both wired and wireless connectivity?
Added info: I tried to connect directly from the computer to the modem, but again, got no connectivity. When I "chatted" with ATT, they told me the modem is set to "bridge", and that I could connect only one device. I don't want to change this setting because I want to use the router for the wireless capability. Besides which, I have more than one computer to connect to the internet.
How come I cannot just plug in and go?
My firmware version is v2.07.1.
I don't know how to find out what hardware version I have.
Other info is "DirectEthernet Connection, Speed: 100.0 Mbps, Signal Strength: Excellent, Status: Connected"
Also "1394 Connection 3, Speed: 400.0 Mbps, Status: Connected"
I don't know what that's for, but thought it might prove useful to those of you who are knowledgeable about such things.
Wireless is ok, but if I'm sitting right next to the router, I'd like to connect with Ethernet and take advantage of the better speed, etc.
Thanks in advance.Just click this link.
-
I have a new Macbook Air 2012, Apple TV 2 and I have tried wired and wireless connections both still result in stuttering during video airplay to the ATV2.
I have even bought a new Airport Extreme Router just to confirm it is not the router and it still didn't help.
I have brought all items in the same room with wired connections and still same issue.
I was thinking maybe ATV 3 might help since it has 2 wifi antennas and faster processor.
Have tried everything I could think of.
This was one of the main reasons I bought a Macbook Air for this airplay feature. Very frustrated.
Any thoughts; any other suggestions would be greatly appreciated.
ThanksThanks for the suggestion.
I also disabled Norton Firewall and restarted the Air and Now I'm able to use Air Play.
I know that the Apple remedy said that to do that in the support article, but I totally forgot I had that enabled..
It actually works. I can even stream to the Apple TV now through my MacBook Air.
BTW, Go into setting under the ATV, and click on update...you'll see that there was another update avaialble for the last gen of ATV...
It does have to restart twice..I guess once to download and and nother to apply. -
Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
I am having trouble making outgoing call or answering incoming call.
When I try to call out from my IP 7961 phone, it fails with the message "unknown number".
For incoming call, it rings but when I pick up the call nothing happens,
Put the receiver back on hook, the phone carries on ringing. I am in UK
and just trying to set up test system with one analogue line. Any help will
be most appreciated. My config of the 2811 router is posted below. All calls ineternally works fine.
Thank you for your help.
hostname Test-CME
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1 10.10.10.10
ip dhcp excluded-address 10.139.139.1 10.139.139.10
ip dhcp pool host
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
option 150 ip 10.10.10.1
ip dhcp pool data
network 10.139.139.0 255.255.255.0
default-router 10.139.139.1
dns-server 10.139.139.5
voice-card 0
no dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
sip
header-passing
registrar server expires max 3600 min 3600
interface FastEthernet0/1
no ip address
no ip mroute-cache
duplex auto
speed auto
no shut
interface FastEthernet0/1.2
description ** Data VLAN **
encapsulation dot1Q 2
ip address 10.139.139.1 255.255.255.0
interface FastEthernet0/1.3
description ** Voice VLAN **
encapsulation dot1Q 3
ip address 10.10.10.1 255.255.255.0
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
tftp-server flash:S00104000100.sbn
tftp-server flash:TERM41.7-0-3-0S.loads
tftp-server flash:term61.default.loads
tftp-server flash:term41.default.loads
tftp-server flash:CVM41.2-0-2-26.sbn
tftp-server flash:cnu41.2-7-6-26.sbn
tftp-server flash:Jar41.2-9-2-26.sbn
tftp-server flash:term70.default.loads
tftp-server flash:term71.default.loads
tftp-server flash:cnu70.2-7-6-26.sbn
tftp-server flash:Jar70.2-9-2-26.sbn
tftp-server flash:TERM70.7-0-3-0S.loads
tftp-server flash:CVM70.2-0-2-26.sbn
control-plane
voice-port 0/3/0
connection plar opx 202
caller-id enable
dial-peer voice 1 pots
incoming called-number .
destination-pattern 9T
port 0/3/0
telephony-service
load 7914 S00104000100
load 7941 TERM41.7-0-3-0S
load 7961 TERM41.7-0-3-0S
load 7970 TERM70.7-0-3-0S
max-ephones 20
max-dn 40
ip source-address 10.10.10.1 port 2000
calling-number initiator
service phone videoCapability 1
system message MKC CME
url services http://10.10.10.1/voiceview/common/login.do
url authentication
http://10.10.10.1/voiceview/authentication/authenticate.do
time-zone 21
date-format dd-mm-yy
voicemail 600
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
moh music-on-hold.au
web admin system name admin secret 0 test
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
secondary-dialtone 9
create cnf-files
ephone-dn 1 dual-line
number 201
label 201
description Sarah
name Sarah
ephone-dn 2 dual-line
number 202
label 202
description Vitthal
name User2 Vitthal
ephone-dn 3 dual-line
number 203 secondary
label 203
description Neil
name User3 Neil
ephone 1
video
username "user1" password 201
mac-address 0018.18EE.947F
type 7961 addon 1 7914
button 1:1
ephone 2
video
username "user2" password 202
mac-address 0018.18BB.B973
type 7941
button 1:2
ephone 3
video
username "user3" password 203
mac-address 0018.1885.6BA2
type 7970
button 1:3Hi
Please find enclosed debug attachment for voice ccapi and ephone. First, I called from outside. Extension 202 rings but when I answered on extension 202 nothing happens. Replace the rceiever and the pone starts ringing again.Second step. I tried to call out by dialing 9 and then number but after a while phone displays unknown number.
Thank you for your help.
Vitthal -
II am having trouble with safari dropping most Internet connections most every time I'm on. This is a first generation iPad. Can this be cried?
This issue was resolved! I didnt think about restoring my computer to factory settings but I did and now my computer works like brand new. basically, just back up your files and do the following:
http://www.youtube.com/watch?v=yPmT5Xbb8p0 -
Trouble with LaCie disk and time machine
HI everyone,
I've been having trouble with using time machine to back-up to my 1 TB LaCie drive (purchased 5/12, unfornuately I was dumb and didn't register the drive and no longer have the box with the serial number and there is no serial number on my drive. The only problem I had up until the end of August was that every so often the LaCie drive (using my FW 800 port) would unmount after waking up from sleep.
The end of August the drive unmounted for no reason while I was on the computer doing a task. Could not get the LaCie drive remounted (rebooting, etc. etc.) To make a long story short, ended up calling apple care who took me through resetting my SMC and PRAM to no avail. Was booted to higher level of support who walked me through trying to repair my drive using the disk utiltiy. When that didn't work, she walked me through erasing and reformatting the LaCie drive and starting a new time machine back-up. Every thing ok until about ten days ago.
Last week, when I woke my iMac up from sleep, I got an error saying that the disk was not ejected properly and I could not mount the drive. Restarting did nothing, the disk did not mount. Shutting down and rebooting seemed to solve the problem and the disk was mounted. Every so often I've had the problem with the disk unmounting after waking up from sleep before. So, I changed my energy sleep preferences. At the end of the day when I am done, I'd unmount the LaCie drive before putting the Mac to sleep using the apple menu.
Today I came in to start my day, plugged the drive in and it would not mount. Tried rebooting nothing. Went into the disk utility, at first the LaCie drive passed the disk verify (6:26:25 and 6:26:38). Then I went into repair disk on the indented drive at 6:27:13, I wasn't sure what it is was doing, thinking that it had hung, I stopped the repair at 6:27:24. Exited disk utility, and the LaCie drive mounted. But I was getting a read only error when I tried to back-up using time machine. So, I went back into disk utility at 6:27:35, when I verified the disk (indented disk), I got an error saying the disk need to be repaired. After several minutes the disk could not be repaired. So, I erased and reformatted the drive. Ran a time machine back-up and it seemed to back-up everything on my hard drive. Just ran another verify disk and it passed.
Is the drive failing? Have some other back-ups of my documents, my address book, iCal and am going to make a backup of some of my pref files and important e-mail files and am going to do some more back-ups after I am done.
Have reached out to the women at apple care whom I talked to last August, but don't expect to hear back from her for at least 24 hours.
Here is my disk utility log
2013-11-07 06:26:25 -0500: Verifying partition map for “LaCie”
2013-11-07 06:26:25 -0500: Starting verification tool:
2013-11-07 06:26:25 -0500: Checking prerequisites
2013-11-07 06:26:25 -0500: Checking the partition list
2013-11-07 06:26:25 -0500: Checking for an EFI system partition
2013-11-07 06:26:25 -0500: Checking the EFI system partition’s size
2013-11-07 06:26:25 -0500: Checking the EFI system partition’s file system
2013-11-07 06:26:25 -0500: Checking all HFS data partition loader spaces
2013-11-07 06:26:25 -0500: Checking Core Storage Physical Volume partitions
2013-11-07 06:26:25 -0500: The partition map appears to be OK
2013-11-07 06:26:25 -0500:
2013-11-07 06:26:25 -0500:
2013-11-07 06:26:38 -0500: Verifying partition map for “LaCie”
2013-11-07 06:26:38 -0500: Starting verification tool:
2013-11-07 06:26:38 -0500: Checking prerequisites
2013-11-07 06:26:38 -0500: Checking the partition list
2013-11-07 06:26:38 -0500: Checking for an EFI system partition
2013-11-07 06:26:38 -0500: Checking the EFI system partition’s size
2013-11-07 06:26:38 -0500: Checking the EFI system partition’s file system
2013-11-07 06:26:38 -0500: Checking all HFS data partition loader spaces
2013-11-07 06:26:38 -0500: Checking Core Storage Physical Volume partitions
2013-11-07 06:26:38 -0500: The partition map appears to be OK
2013-11-07 06:26:38 -0500:
2013-11-07 06:26:38 -0500:
2013-11-07 06:27:13 -0500: Disk Utility started.
2013-11-07 06:27:21 -0500: Verifying and repairing partition map for “LaCie”
2013-11-07 06:27:21 -0500: Starting repair tool:
2013-11-07 06:27:21 -0500: Checking prerequisites
2013-11-07 06:27:21 -0500: Checking the partition list
2013-11-07 06:27:21 -0500: Checking for an EFI system partition
2013-11-07 06:27:21 -0500: Checking the EFI system partition’s size
2013-11-07 06:27:21 -0500: Checking the EFI system partition’s file system
2013-11-07 06:27:23 -0500: Checking all HFS data partition loader spaces
2013-11-07 06:27:24 -0500: Reviewing boot support loaders
2013-11-07 06:27:24 -0500: Checking Core Storage Physical Volume partitions
2013-11-07 06:27:24 -0500: Updating Windows boot.ini files as required
2013-11-07 06:27:24 -0500: The partition map appears to be OK
2013-11-07 06:27:24 -0500:
2013-11-07 06:27:24 -0500:
2013-11-07 06:27:35 -0500: Verifying volume “LaCie”
2013-11-07 06:27:35 -0500: Starting verification tool:
2013-11-07 06:27:35 -0500: Checking file system2013-11-07 06:27:35 -0500: Error: This disk needs to be repaired. Click Repair Disk.2013-11-07 06:27:35 -0500:
2013-11-07 06:27:35 -0500: Disk Utility stopped verifying “LaCie”: This disk needs to be repaired. Click Repair Disk.
2013-11-07 06:28:05 -0500:
2013-11-07 06:28:13 -0500: Verify and Repair volume “LaCie”
2013-11-07 06:28:13 -0500: Starting repair tool:
2013-11-07 06:28:13 -0500: Checking file system2013-11-07 06:28:13 -0500: Volume repair complete.2013-11-07 06:28:13 -0500: Updating boot support partitions for the volume as required.2013-11-07 06:35:05 -0500: Stopped by user
2013-11-07 06:44:56 -0500: Disk Utility started.
2013-11-07 06:45:20 -0500: Verifying volume “LaCie”
2013-11-07 06:45:20 -0500: Starting verification tool:
2013-11-07 06:45:20 -0500: Checking file system2013-11-07 06:45:20 -0500: Checking Journaled HFS Plus volume.
2013-11-07 06:45:20 -0500: Checking extents overflow file.
2013-11-07 06:45:20 -0500: Checking catalog file.
2013-11-07 06:45:59 -0500: Missing thread record (id = 5057741)
2013-11-07 06:46:06 -0500: Checking multi-linked files.
2013-11-07 06:46:19 -0500: Checking catalog hierarchy.
2013-11-07 06:46:38 -0500: Invalid directory item count
2013-11-07 06:46:38 -0500: (It should be 0 instead of 4)
2013-11-07 06:46:38 -0500: Invalid volume directory count
2013-11-07 06:46:38 -0500: (It should be 166840 instead of 166841)
2013-11-07 06:46:38 -0500: Checking extended attributes file.
2013-11-07 06:47:05 -0500: Checking multi-linked directories.
2013-11-07 06:48:10 -0500: Checking volume bitmap.
2013-11-07 06:48:12 -0500: Checking volume information.
2013-11-07 06:48:12 -0500: The volume LaCie was found corrupt and needs to be repaired.
2013-11-07 06:48:12 -0500: Error: This disk needs to be repaired. Click Repair Disk.2013-11-07 06:48:12 -0500:
2013-11-07 06:48:12 -0500: Disk Utility stopped verifying “LaCie”: This disk needs to be repaired. Click Repair Disk.
2013-11-07 06:48:12 -0500:
2013-11-07 06:50:02 -0500: Verify and Repair volume “LaCie”
2013-11-07 06:50:02 -0500: Starting repair tool:
2013-11-07 06:50:02 -0500: Checking file system2013-11-07 06:50:02 -0500: Checking Journaled HFS Plus volume.
2013-11-07 06:50:02 -0500: Checking extents overflow file.
2013-11-07 06:50:02 -0500: Checking catalog file.
2013-11-07 06:50:41 -0500: Missing thread record (id = 5057741)
2013-11-07 06:50:48 -0500: Checking multi-linked files.
2013-11-07 06:51:02 -0500: Checking catalog hierarchy.
2013-11-07 06:51:20 -0500: Invalid directory item count
2013-11-07 06:51:20 -0500: (It should be 0 instead of 4)
2013-11-07 06:51:20 -0500: Invalid volume directory count
2013-11-07 06:51:20 -0500: (It should be 166840 instead of 166841)
2013-11-07 06:51:20 -0500: Checking extended attributes file.
2013-11-07 06:51:47 -0500: Checking multi-linked directories.
2013-11-07 06:52:55 -0500: Checking volume bitmap.
2013-11-07 06:52:56 -0500: Checking volume information.
2013-11-07 06:52:56 -0500: Repairing volume.
2013-11-07 06:52:56 -0500: Missing directory record (id = 5057741)
2013-11-07 06:52:56 -0500: Look for missing items in lost+found directory.
2013-11-07 06:53:10 -0500: Rechecking volume.
2013-11-07 06:53:10 -0500: Checking Journaled HFS Plus volume.
2013-11-07 06:53:10 -0500: Checking extents overflow file.
2013-11-07 06:53:10 -0500: Checking catalog file.
2013-11-07 06:53:16 -0500: Incorrect number of thread records
2013-11-07 06:53:22 -0500: Checking multi-linked files.
2013-11-07 06:53:35 -0500: Checking catalog hierarchy.
2013-11-07 06:53:53 -0500: Invalid directory item count
2013-11-07 06:53:54 -0500: (It should be 5 instead of 6)
2013-11-07 06:53:54 -0500: Invalid volume directory count
2013-11-07 06:53:54 -0500: (It should be 166844 instead of 166842)
2013-11-07 06:53:54 -0500: Invalid volume file count
2013-11-07 06:53:54 -0500: (It should be 1056326 instead of 1056321)
2013-11-07 06:53:54 -0500: Checking extended attributes file.
2013-11-07 06:54:20 -0500: Checking multi-linked directories.
2013-11-07 06:55:25 -0500: Checking volume bitmap.
2013-11-07 06:55:26 -0500: Checking volume information.
2013-11-07 06:55:26 -0500: Repairing volume.
2013-11-07 06:58:06 -0500: Rechecking volume.
2013-11-07 06:58:06 -0500: Checking Journaled HFS Plus volume.
2013-11-07 06:58:06 -0500: Checking extents overflow file.
2013-11-07 06:58:07 -0500: Checking catalog file.
2013-11-07 06:58:12 -0500: Incorrect number of thread records
2013-11-07 06:58:18 -0500: Checking multi-linked files.
2013-11-07 06:58:31 -0500: Checking catalog hierarchy.
2013-11-07 06:58:50 -0500: Invalid volume directory count
2013-11-07 06:58:50 -0500: (It should be 166844 instead of 166842)
2013-11-07 06:58:50 -0500: Invalid volume file count
2013-11-07 06:58:50 -0500: (It should be 1056326 instead of 1056321)
2013-11-07 06:58:50 -0500: Checking extended attributes file.
2013-11-07 06:59:17 -0500: Checking multi-linked directories.
2013-11-07 07:00:22 -0500: Checking volume bitmap.
2013-11-07 07:00:24 -0500: Checking volume information.
2013-11-07 07:00:24 -0500: Repairing volume.
2013-11-07 07:03:03 -0500: Rechecking volume.
2013-11-07 07:03:03 -0500: Checking Journaled HFS Plus volume.
2013-11-07 07:03:03 -0500: Checking extents overflow file.
2013-11-07 07:03:04 -0500: Checking catalog file.
2013-11-07 07:03:09 -0500: Incorrect number of thread records
2013-11-07 07:03:15 -0500: Checking multi-linked files.
2013-11-07 07:03:29 -0500: Checking catalog hierarchy.
2013-11-07 07:03:47 -0500: Invalid volume directory count
2013-11-07 07:03:47 -0500: (It should be 166844 instead of 166842)
2013-11-07 07:03:47 -0500: Invalid volume file count
2013-11-07 07:03:47 -0500: (It should be 1056326 instead of 1056321)
2013-11-07 07:03:47 -0500: Checking extended attributes file.
2013-11-07 07:04:14 -0500: Checking multi-linked directories.
2013-11-07 07:05:19 -0500: Checking volume bitmap.
2013-11-07 07:05:20 -0500: Checking volume information.
2013-11-07 07:05:20 -0500: The volume LaCie could not be repaired after 3 attempts.
2013-11-07 07:05:21 -0500: Volume repair complete.2013-11-07 07:05:21 -0500: Updating boot support partitions for the volume as required.2013-11-07 07:05:21 -0500: Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.2013-11-07 07:05:21 -0500:
2013-11-07 07:05:21 -0500: Disk Utility stopped repairing “LaCie”: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
2013-11-07 07:05:21 -0500:
2013-11-07 07:09:45 -0500: Disk Utility started.
2013-11-07 07:11:45 -0500: Preparing to erase : “LaCie”
2013-11-07 07:11:45 -0500: Partition Scheme: GUID Partition Table
2013-11-07 07:11:45 -0500: 1 volume will be erased
2013-11-07 07:11:45 -0500: Name : “LaCie”
2013-11-07 07:11:45 -0500: Size : 999.86 GB
2013-11-07 07:11:45 -0500: File system : Mac OS Extended (Journaled)
2013-11-07 07:11:45 -0500: Unmounting disk
2013-11-07 07:11:45 -0500: Erasing
2013-11-07 07:11:54 -0500: Initialized /dev/rdisk1s2 as a 931 GB HFS Plus volume with a 81920k journal
2013-11-07 07:11:54 -0500: Mounting disk
2013-11-07 07:11:54 -0500: Erase complete.
2013-11-07 07:11:54 -0500:
2013-11-07 10:38:00 -0500: Disk Utility started.
2013-11-07 10:38:12 -0500: Verifying volume “LaCie”
2013-11-07 10:38:12 -0500: Starting verification tool:
2013-11-07 10:38:14 -0500: Checking file system2013-11-07 10:38:14 -0500: Checking Journaled HFS Plus volume.
2013-11-07 10:38:14 -0500: Checking extents overflow file.
2013-11-07 10:38:14 -0500: Checking catalog file.
2013-11-07 10:38:29 -0500: Checking multi-linked files.
2013-11-07 10:38:29 -0500: Checking catalog hierarchy.
2013-11-07 10:38:41 -0500: Checking extended attributes file.
2013-11-07 10:39:04 -0500: Checking multi-linked directories.
2013-11-07 10:39:31 -0500: Checking volume bitmap.
2013-11-07 10:39:32 -0500: Checking volume information.
2013-11-07 10:39:32 -0500: The volume LaCie appears to be OK.
2013-11-07 10:39:32 -0500: Repair tool completed:
2013-11-07 10:39:32 -0500:
2013-11-07 10:39:32 -0500:I just got a call back from the upper level support person at apple care who had been advising me on my trouble with time machine and my LaCie 1 TB FWD. I had sent her much of the same verbiage as I posted here. As some of you have probably figured out, the verdict is that the drive is probably failing. She says this because I have had to do two erase and reformats. She thought that the intermitant problem that I have had with the drive unmounting when my iMac wakes from sleep could be related to the drive failing.
In the meantime I have a secondary back-up (not using time machine) and the LaCie 1 TB FWD is working for the moment.
Thanks to all who read all my verbiage.
And in the meantime, I've learned something. I marked this question as solved. But I'm open to other things to try.
Message was edited by: njtreehugger minor edits and update -
Can I share my internet from my Imac with my Ipad and simultaneously connect to a airport express that I use to remotely to connect speakers?
The big problem that I'm having is that when internet sharing via the airport I can not simultaneously connect with my airport express. It would be great to be able to share internet from my Imac so I can be using my Ipad and at the sametime have my wife use the airport express to stream music in a different room. It would be awesome to be able to have the ability to do both. Does anybody know how?Unless your iMac was made before 2006 (this forum is for old iMacs), you might get better assistance by posting in one of the following forum areas:
AirPort
Using iPad
iMac (Intel) -
Trouble With Opening InDesign and now Photoshop and Illustrator
First off I apologize if this isn't in the correct section. I couldn't find a section specific to my problem since it involves multiple aspects of Adobe products. I was having trouble with InDesign, it kept crashing. So I followed all of the advice I could find on the forums about deleting the preferences and cache information in the Library folder, and that didn't seem to make a difference. So then I thought maybe it needed an update, so I logged into Adobe Application Manager and sure enough, it did. So I clicked on "download" and it stalled there too. Then the manager became unresponsive. I couldn't cancel the update or log out or anything. So then I saw in the forum someone suggested the Adobe Creative Cloud Cleaner Tool if your manager becomes unresponsive. I ran that and then shut my computer off. When I turned it back on, InDesign started working BUT my Photoshop is completely gone from my system (I never messed with it in the first place since I wasn't having any trouble with it.) And the when I tried to click on Illustrator it said "Do you want to begin your trial?" Huh?
I have had a subscription since 2012, why on earth would it suddenly think that I no longer should have access to these programs? If I log on to my Adobe account it shows my subscription and that it's up to date (last payment was April 5, 2015). The versions I was using were the CS versions that I had downloaded directly from Adobe and when I used to have any trouble or when I got a different computer I could just log into my account and then redownload them. They are no longer showing under my products, so I can't figure out what on earth is going on. The website has changed since the last time I downloaded them, so that partly could be me, but I thought they would at least be showing up under products. I contacted Adobe support and the first person I talked to on chat said "this is clearly a technical issue I am transferring you to someone better suited for this," but that's all he said. And I haven't heard from anyone since so I thought I'd make a topic and see if anyone else out there has had a similar problem.The versions I am using are the CS6 versions.*
Maybe you are looking for
-
Deploying EJB 3.0 MDB on Weblogic 10.3
My MDB is as follows: package test; import javax.ejb.ActivationConfigProperty; import javax.ejb.MessageDriven; import javax.jms.Message; import javax.jms.MessageListener; @MessageDriven(mappedName = "mdb01/queue01", activationConfig = { @Ac
-
I recently purchased an ipod touch.
The pc i was using has internet access, so i was able to d/l itunes. For the next 3 months (with my new pc) i cannot access the net. How can i get itunes onto my pc without internet access? The Apple call centre i contacted told me to burn a copy of
-
Where is "Group compilations while scanning" in the advanced menu ?
Hello I can't find "Group compilations while scanning" in the advanced menu. I really did check that the music went a compilation yet. Thank you for answer
-
Can't run any JRE or JDK utilities-Win XP SP1
Hi I'm trying for quite a few days now but can't solve this problem. I installed the J2SDK 1.4.01 and sun 1 forte co-bundle which installed JRE 1.4.1 and Web Start. The installation goes fine but when I try to run any of the utilities I get a catastr
-
Have Apple 5... Suddenly photos are coming out too dark and poor color....any ideas as to problem
Camera taking poor pictures....too dark, flash goes off but picture quality poor. Just started this recently