[SOLVED] Updated but now getting no eth0
Hi all,
Updated my virtual machine to the latest release but now I no longer have eth0.
Starting Network [BUSY]
Error: unknown interface in /etc/rc.conf: 'eth0'
Not sure where to look now. I can't remember the command that's replaced ifconfig either. Good job this is the newbie corner I guess!
Cheers beforehand.
Last edited by Swarfega (2012-07-18 13:04:59)
ebal wrote:
whats the output of
ip a
ip r
I just see a 'lo' and nothing else.
'ip r' doesn't seem to do anything.
The hypervisor is VMware ESXi 5 if that helps. I did notice the latest updated had an updated open-vm-tools component. Related maybe?
IsSuE wrote:dmesg, ip link and lspci -vv output needed
Also chech your udev rules
I can't copy and paste from the console window sorry
*Edit*
Fixed this, although not properly. For some reason the interface just disappeared. I removed the Flexible NIC and replaced it with an E1000.
This also happened to my other virtual Arch box too so it wasn't just a one off.
Last edited by Swarfega (2012-07-18 13:04:46)
Similar Messages
-
I downloaded the recent Pages update but now I can not open some documents done in the past year. I get an error saying that I need to download a newer version of Pages. I am running version 4.3. Do I have to purchase an update of Pages?
You are not on Mountain Lion anymore, right? You are on Mavericks and have downloaded Pages 5 and then created docuemnts in it which can't be opened in Pages 09.
No, you don't have to buy a newer Pages but you have to be particular about which version you use. -
before my iphone need to update 41 softweare so yesterday i update but now i cannot open its icone only emergency call only but i can recive call so wht should i do for it.
Are you getting a message about an unsupported SIM? It sounds like you had a phone that had been hacked to work on a network other than the one it was locked to and updating it has re-locked the phone to the original network.
Where exactly did you get the phone? What network are you on? If you did not purchase your phone directly from DU or from Etisalat (assuming you are using a carrier in the UAE) or from a carrier in the country where you purchased the phone or directly from Apple, then you got a gray market phone and it was most likely hacked to unlock it in the first place. Most of these gray market, hacked phones come from the US and were originally locked to AT&T.
Only the carrier the phone is locked to can authorize an unlock. If it is locked to AT&T, they will NOT authorize an unlock.
If any of my assumptions are incorrect, I apologize. We need more information, though to make a recommendation. -
i just upgraded my iphone 3gs to ios 6 not sure if it updated but now when i turn on my phone it says automatically that i need to connect it to itunes using the USB port but when i connect it it comes up as new hardware and cannot find a program/software for my device even though i have the latest itunes on my computer. i have tried reinstalling itunes but it still cannot find my phone and now i cannot use my phone as it is stuck on the sync to itunes screen
Have you downloaded and installed the latest version of iTunes from here:
http://www.apple.com/itunes/download/ -
Hello I have a problem to update Imovie. I want to update but I get "There is a billing problem with a previous purchase" What do I do?
Restore from iTune Backup
1. Settings>General>Reset>Erase all content and settings
2. You will be asked twice if you want to erase iPad
3. Slide to set up
4. Select Language
5. Select Country
6. Enable Location Service
7. Choose Wi-Fi Network
8. Enter Wi-Fi password
9. (a) Setup as new (b) Restore from iCloud Backup (c) Restore from iTune Backup
10. Select "Restore from iTune Backup"
11. You will be instructed to connect to iTune (computer)
On computer
12. Two options offered
13. (a) Set up as new iPad (b) Restore from backup (a list of backup will be shown)
14. Select Restore from backup and select the backup
15. Continue
16. Restoring iPad from backup
17. The settings for iPad restored -
I am developing a book via email with a collaborator. iBooks Files are sent to me via a link to preview on iPad. This worked fine for a while but now getting download errors and the unhappy mac face saying download failed. Any help appreciated. Very frustrating!
I can see that this issue has been quite extensive, and frustrating, and I am so sorry for all that has happened societygirl! I would like to help you work this issue out. Please follow & send me a Direct Message, so I can get your account specifics and help finally bring this to a resolution.
Thank you,
MichelleH_VZW
Follow us on Twitter @VZWSupport -
HT4623 I completed the ios update but now my contact information is missing?
I completed the ios update but now my contact information is missing?
Your contacts will be in whatever program you have chosen to sync.
-
i am trying to restore my iphone after an ios update but keep getting a message saying it is unable to restore. PLease assist
The phone was jailbroken, wasn't it?
-
I have updated both my iphone 4G and my husbands 4G with the nAew 5 update but now have his contacts on my phone and everytime he downloads an app it goes on my phone. How can I change this? Do I have to have two separate Apple ID's
Try this
http://support.apple.com/kb/ht1495
Hope it helps. -
Hello Sir I have an iPhone 4 and when i updated that it got updated but now for restore the data it is showing me the message The "iPhone" could not be activated because an unknown error occurred (0xE8000004). Please try again later. please help me.
Hello Amarchand Sharma,
Are you working with a Windows computer? If so, the resource below may help you troubleshoot the issue you are having restoring your iPhone.
iOS: Unknown error containing '0xE' when connecting to a Windows PC - Apple Support
http://support.apple.com/en-us/TS3221
Regards,
Judy -
HT4623 I put my IPhone 4 to update but now is lock and showing error 3194, what my be the problem?
I put my IPhone 4 to update but now is lock and showing error 3194, anyone now what to do? please.
Same issue, I hope someone on here can figure this out and share the information. I was on the phone with apple for over 2 hours trying to fix. I guess I have to make another call on Monday!
-
I just got the ios 8 update but now my ipod 5 wont turn on
I just got the IOS 8 update but now my ipod 5 wont turn on.
If it has NEVER been jailbroke, here are some standard repair procedures:
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, read this. -
TV Screen says "No signal" when I try to use apple TV. Was working. ie Little Apple symbol would appear on TV screen, but now get "No signal" Internet connection working (light on apple TV)...tried new HDMI cable but still "No signal" HELP please
Same exact problem with my Apple TV. Worked like a charm the first two times we used it. Haven't used it in about a month, now no Apple logo when I turn it on, or the logo appears momentarily and distorted, and then an error message from my Samsung HD TV: Mode Not Supported.
What changed?
Bill O'Rourke
***@***********.com
<Email Edited by Host> -
still running adobe cs2 on leopard. but now get unexpected quit msg. and wont launch. any chance that when i installed then uninstalled GENIEO yesterday something went wrong? how to fix? can i reinstall cs2 from original discs? bystephenftlaud
Hi,
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
Open Console in Applications>Utilities & see if there are any clues or repeating messages when trying to open CS2. -
still running adobe cs2 on leopard. but now get unexpected quit msg. and wont launch. any chance that when i installed then uninstalled GENIEO yesterday something went wrong? how to fix? can i reinstall cs2 from original discs?
Hi,
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
Open Console in Applications>Utilities & see if there are any clues or repeating messages when trying to open CS2.
Maybe you are looking for
-
How do I add a movie theater to the Siri database?
How do I add a movie theater to the Siri database?
-
Need to read data from a jsp and insert in other jsp
Hi, I have a jsp where i need to read from another jsp(which has data " header ---insert -----footer") and find a string "insert" in it and replace that string with a some value in the current jsp. Thanx in Advance. Sridhar.
-
Hi gurus, I have exposed my application module as a webservice. Now I want to store them in MDS and also want to refer them from MDS. I have following questions around this 1. What advantage I would get if I store them in MDS? I believe all consumer
-
Is Premiere Pro CC or CS6 better for late-2011 MacBook Pro?
Hi, I'm trying to decide on whether to get Creative Cloud or CS6 version of Premiere Pro - my main consideration is that the program run smoothly (cost is not a big issue since it's for an institution) - I'm not doing anything heavy duty, just simple
-
Your computer has been restarted because of problem
Hello. My iMac opens this message every day. Almost every time I turn off my computer it does not go off, this message is opened, the computer is restarted. Here's a log of the last time. Please help me solving this problem. Interval Since Last Panic