Some advice needed Please Quicksilver 800MHZ

I have a Quicksilver PowerMac 800MHz.
Due to ram problems I need to replace the ram in this machine. I am running Tiger 10.4.11 and it is working fine at the moment.
I have read that if I cam running Tiger I can put 2 Gig of ram in this machine but before I spend money I need to know for sure how much ram I am able to put in. I am not sure if my Quicksilver is an older one or newer one Machine (CK132HANKSD). Can someone please help on this as at the moment I have only two 128 in place PC133 333 to keep me going.

You only have 3 RAM slots. The max RAM per slot is 512MB.
 Cheers, Tom

Similar Messages

Some advice needed please

Hi,
I am currently staying with my folks, and have downloaded itunes on their pc. I have signed in and have authorised the computer. It is recognising my ipod touch and i have run diagnostic tests and everything comes back as working successully...
However! I have imported cd's to the library but they are not syncing onto my ipod. I have also purchased a tv programme from the store, and again, this is not syncing onto my ipod.
Does anyone have any idea as to how i can resolve this?
Thanks in advance.
L

You need to update manually...
Transfer music manually
Backup your music though, as if anything happens to your iPod, you may loose your music.
btabz

Some advice needed please for X-fi elite

Hello i just recently purchased a sound blaster X-fi elite pro i am going to build a computer around it, is there anyone out there who could advise me on what type of motherboard would be suitable ? thank you

You only have 3 RAM slots. The max RAM per slot is 512MB.
 Cheers, Tom

I am using InDesign CS5. I have a body of text which is ranged left with tabbed indents. My client now wants the copy to be justifed, keeping the tabbed indents. Help and advice needed please!

I am using InDesign CS5. I have a body of text which is ranged left with tabbed indents. My client now wants the copy to be justifed, keeping the tabbed indents. Help and advice needed please!

Hi
That screen grab helps a lot. There’s a much easier way of doing what you’re doing.
Remove all your tabs and set the text in justified paragraphs.
I’ve typed in dummy text in the example I made below, but after “19.1” put in a space and put your blinking cursor after the space and before the ’N’ of ‘Notices'.
Then hold down the Command key and hit Backspace (on Mac at least - it’s the key between the Inverted commas/ apostrophe key and the return key).
The text will jump into place the way you want it to.
Hope that helps
Paul
PS You can set a tab, instead of using a space, in the description I gave above. So, after 19.1 or 19.2 or 19.185 etc etc insert a tab, then hit the Command Backspace after every paragraph number and they'll all line up exactly together. You'll find that editing text within the paragraphs
after you've set it will be LOADS easier this way.
You can put the tab anywhere you want it to be using 'Command-ShiftT' and putting a 'left align' tab just after the number. Just type the Command Backspace after the paragraph number and it'll work

Tech advice needed please!

I just downloaded iTunes, once it was done I clicked to open it and it took me to the t&cs which I agreed to, then did nothing. Every time I click to open it takes me back to the same t&cs. Tried uninstalling & re-installing, same problem. Tried a repair on it too. Any ideas?

There are many users have the latest do not have this issue. There may be some files need to be removed during uninstall were not removed. You may need to uninstall and reinstall from scratch.
1. Go to Microsoft website to fix install and Unistall problems. Click "Run now" from Fix it to remove all iTunes & related installer files:
http://support.microsoft.com/mats/Program_Install_and_Uninstall
Be aware that Windows Installer CleanUp Utility will not remove the actual program from your computer. However, it will remove the installation files so that you can start the installation, upgrade, or uninstall over.
2. You should remove all instances of iTunes and the rest of the components listed below:
it may be necessary to remove all traces of iTunes, QuickTime, and related software components from your computer before reinstalling iTunes.
Use the Control Panel to uninstall iTunes and related software components in the following order:
iTunes
QuickTime
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support (iTunes 9 or later)
(Referenceinstructions from Apple article listed here: http://support.apple.com/kb/HT1923 to remove all components)
3. Reboot your computer. Next, download iTunes from here:http://www.apple.com/itunes/download/ and install from scratch

Some general advice needed please

Until today my network was DSL, AE802.11g with ethernet external drive and usb printer, a cube and printer on a remote AE802.11g and an express for the stereo. I had 3 laptops connecting except from one room that I want to move a printer to and use as an office. So I bought some more kit to extend the network.
A new AE802.11n and another express arrived today. Because the house is big with thick walls I think I need at least one airport set up as a relay rather than remote. After reading the discussions I managed to get the new AE set up and connected to the DSL. but, I seldom get more than 1 or 2 AE or expresses show up in airport utility making it hard to set them to join the network which seems to keep disappearing. The most remote AE is near one of the expresses but does not see the network.
Any suggestions for the optimal settings for each device? And what order should I set them up in?

Thank you. Having the airports all in proximity was the key and, of course, I eventually found the same advice in an apple help file. I set the new AExtreme up as WDS main with an ethernet disk for backups and music. An old AExtreme as WDS remote serves the Cube by ethernet and a usb printer. An AExpress as WDS remote serves one stereo. The other AExpress is WDS relay serving another stereo and helping the network reach the office where the last old AExtreme is WDS remote with another USB printer. The 3 mac laptops are happy. I have yet to try any PCs.

Some good advice needed please!

Hi
We are planning to develop an application that offers a web service on the Internet and since we are more familiar with J2SE than J2EE we were thinking about using
javax.jws.WebService and javax.jws.WebMethod in a good old Desktop application. To handle possible high traffic we are planning to use java.util.concurrent.ThreadPoolExecutor.
Our question is ... Assuming adequate hardware and bandwith, will this approach do the job well or are there any pitfalls that we should be aware of?
Many thanks in anticipation.

I posted to your other thread some suggestions for Network connections.
Specific to your question here, the more relevant information entered in the Network panel, the more specific the Network connection. Otherwise, default values set the system to "automatic" which means time can be potentially wasted searching for a Network connection, and hence, the lag-time. The DHCP client ID box adds more specific information for Safari to access, thereby increasing speed. I'm guessing here, but since you still have an E-mail account with Cox, you may have access to their Network.
As I mentioned in my other posts, you may want to speak with Adelphia directly about your browsing experience. They may have other codes you can try to enhance browsing performance.
iMac G5 Rev C 20" 2.5gb RAM 250 gb HD/iBook G4 1.33 ghz 1.5gb RAM 40 gb HD Mac OS X (10.4.8) LaCie 160gb d2 HD Canon i960 printer

Hard drive advice needed please

Hi Guys
I'll shortly be taking the plunge on a shiny new MacBook Pro, after reading various threads I'm still unsure about HD size and RPM.
Ideally I'd like the 200GB drive, but in use just how much slower would it be? I need to access tiff, video and music files, and up to now use an external drive which occasionally chokes on video and music on my trusty 800MHz PowerBook
I use photoshop and various other graphics applications, as well as video editing........So will I find the HD rpm an issue? is it better to settle for the 160GB?
Your advice would be appreciated
ED
G4 Quicksilver + G4 PowerBook + AirPort Extreme Mac OS X (10.4.4) 60GB iPod video and several pet LaCie hard drives

The 200GB 4,200RPM drive is faster than most if not all 4,200RPM drives as it has a greater number of platters than most 4,200RPM drives.
Click the link below to see how it faired in some tests. It was near the bottom in terms of perfomance compared to faster RPM drives but against other 4,200RPM drives it did well.
http://tomshardware.co.uk/2006/10/12/fujitsusmhv2200btuk/page3.html

Connection Advice Needed Please

Hi All
I moved house over a week ago and asked to transfer my BT Services over (but thats a whole other shambolic issue). At my previous house, my HH5 was connected to the Master Phone Socket and I had Infinity 2 Unlimited. However, the new house already has FTTP installed - with an ONT box and back up battery box on the wall.
I've not been able to get any advice from BT, but can someone tell me if I just plug my devices straight into the wall mounted box or do I plug my old HH5 into the ONT box and use my old wireless SSID as usual? Or do I still just plug my HH5 into the main phone socket?
I did not ask for the FTTP super fast service, so they should be activating my old 76MBps Infinity 2 service.
Many thanks
Liz

Hi EWINMK17
If you have FTTP and already have the ONT (Openreach optical network box) and backup battery installed, then all you need to do is connect your Home Hub 5 via the WAN port (may be coloured red) on the back of the Home Hub 5 to the LAN1/Port1 port on the ONT with an ethernet cable.
Are there any lights light up on the ONT?
Here's some information about the lights on the ONT box: http://bt.custhelp.com/app/answers/detail/a_id/36945/~/fibre-home-phone-service%3A-lights-on-the-ope...
Have a look at page 11 on the user manual on how to connect your HH5 to the ONT here http://btsupport.custhelp.com/ci/fattach/get/3309418/1381227399/redirect/1
jac_95 | BT.com Help Site | BT Service Status
Someone Solved Your Question?
Please let other members know by clicking on ’Mark as Accepted Solution’
Try a Search
See if someone in the community had the same problem and how they got it resolved.

Installing a second hard drive in a G4 - advice needed please

Hi......
I have a G4 Quicksilver (2002) model and I also have a G4 Digital Audio model as well which is currently surplus to requirements.....
I would like to take out the 20Gb hard drive from the older G4 and put it into the Quicksilver as a second internal hard drive (for extra storage capacity....)
I have seen the instructions regarding installing a second hard drive and it doesn't seem to complicated....
I just want to check because the 20Gb hard drive has the operating system on it for the older G4.....
Do I have to fire up the machine and erase the hard drive and then take it out and put it into the Quicksilver...?
Or am I able to simply take it out, put it in the Quicksilver and erase it when I restart the machine....?
I don't have the original installation discs for the OSX...
I talked to a Mac technician at work and he said I can just take out the 20Gb hard drive and put it in as a 'slave' drive and I have to 'bend some pins' (I think he said) when I install it.........and I can then erase the second hard drive and use it as storage.....
any advice would be greatly appreciated.....
Thanks

Hi, craigkelleigh -
Ony many drives the label showing jumper pins configurations will be on the end of the drive, just above the block of pins; on other drives it may be on the top, rarely on the bottom.
The block of jumper pins is at the same end of the drive where the data cable (wide, flat ribbon cable) and the power connector plug in.
It is best to move the jumpers before installing the hard drive - they're quite small and hard to manipulate in a confined space. Important - do not move jumper pins if the drive is powered up (running).
As far as removing and installing the drive, you can view/download a how-to PDF or movieclip from these pages -
G4 (Digital Audio) - http://docs.info.apple.com/article.html?artnum=75313
G4 Quicksilver - http://docs.info.apple.com/article.html?artnum=75314
In addition, with regard to specific jumper positions, that depends on the make (and sometimes the model) of the drive. There are some resources available on-line, such as jumper diagrams for specific drives. If you would give us the specific make (manufacturer) and model number of your hard drive (that info should be shown on labels affixed to the drive), we may be able to direct you to a specific website page with that info.

Russian and Chinese Flash movies - general advice needed please

Hi all -
This is a plea for some general 'jumping off' advice. I am an experienced Flash developer but now have a request to convert an existing xml-fed movie into both Russian and Chinese. I speak neither of these languages so we have had the content of the movie translated by a professional translation service.
The movie contains both png/jpgs with embedded text - created in Fireworks and also (for the bulk of the content) external xml files. I still need to be able to develop in an English environment - so purchasing a full version of Flash/Fireworks in Russian/Chinese would be folly. How should I go about this? If it is a matter of fonts - where should I get them from? And are there any considerations to be met with regards the xml files? Basically, I would really appreciate some general advice on this subject as it is completely new ground for me.
Much obliged,
Hugh

Thank you. Having the airports all in proximity was the key and, of course, I eventually found the same advice in an apple help file. I set the new AExtreme up as WDS main with an ethernet disk for backups and music. An old AExtreme as WDS remote serves the Cube by ethernet and a usb printer. An AExpress as WDS remote serves one stereo. The other AExpress is WDS relay serving another stereo and helping the network reach the office where the last old AExtreme is WDS remote with another USB printer. The 3 mac laptops are happy. I have yet to try any PCs.

Oracle "guru"'s advice needed please :-)

I think I need an Oracle "guru" for this situation. 2 issues:
1) Installed Oracle on a Standalone desktop with Win 2K Professional. Database Config. Assistant created Database - 9i Version of Oracle Standard Version. I get 2 errors: Ora 12541 and ora 12154 - all relating to TNS No Listener or failed to resolve service name. Now, I'm quite the newbie but I can't understand why I would need to configure this stuff on a standalone machine. It also asks me for ID and password and when I put the correct one in, that's when I get the No Listener error, however, I did indeed configure one. My Tsnnames.ora and listener.ora do have the database in them and everything in those files seems correct. The DB name is SteveTe and the PC (or host I guess is "Tower"). How can I configure or fix this?
2) I used Migration Workbench to "import" an Access DB into Oracle which was successful BUT I also expected to see the database in Enterprise Manager and want to use SQL + to do queries with it. How can I do this? Currently I cannot do it and the DB doesn't show in Enterprise manager. Furthermore, if I attach it manually, it still asks me for a ID and Password and it doesn't have one so how do I get around this?
If someone can help, please send me some detailed instructions to get me out of the Oracle "quicksand" that I'm in. Thanks,
Steve

I would suggest using XSL to define your presentation layer. This will be much faster than accessing tables. It also allows you to change your presentation on-the-fly with different XSL files.
Storing the XML in the database is a good idea. Especially in 9i which will have native XML support with the use of a new datatype called XMLType. It uses CLOB's under the covers, but will give you native access to your XML data.

Advice needed please regarding a new phone line

Hi all,
I would appriciate any advice please. I will start from the beginning i placed my order with BT on 26 july calls and broadband they said they had to send an enginner out and the earliest date was 16th August which has been i waited in betwwen 12 and 5 and no enginner arrived i then rang bt i was so angry. After lots of phonecalls from them yestarday they are coming tommorrow.
I need advice on the socket i have one in my flat but what i dont have is a wire that goes accross the wall i am not sure if that lead is in the socket i have not touched the socket since i moved in 2 years ago i do not want to touch it as me and leads do not get on lol!! would the enginner put the cable in if there isnt one???
Thanks in advance

'I need advice on the socket i have one in my flat but what i dont have is a wire that goes accross the wall i am not sure if that lead is in the socket i have not touched the socket since i moved in 2 years ago i do not want to touch it as me and leads do not get on lol!! would the enginner put the cable in if there isnt one???'
Have you ever had a working land line in the flat, is the flat a new(ish) build? It is possible the lead in, that is the wire that connects the socket to the outside Block Terminal or Distripution Point is behind the wall.
Most new builds will have Openreach or the developer put the wiring in before they put the wall in to hide it so there isn't un-sightly wires everywhere. My house is a new build, a mid town house and the master socket is at the back of the house in the living room but the connection point outside is on the front of the house, there is no visible wire so I assume it goes up the wall, across the hall ceiling into the living room then down the wall again to where it is. I know it won't go under the floor because I visted the house a few times during the build process and the floor was put in before the phone socket was.
I suppose its nice you can't see the wire but I am unsure what they will do if it ever needs replacing as I don't know if its feeds through duct type pipeing where they can pull it through?
Anyway to answer your question if it needs a cable then yes the engineer will put one on.

Advice needed :please help

Hi,
We have an application that has 2 database tables that hold presentation information as:
Table :- screens_info
Contents of a record :- what is the background color , title , link colors etc. for a screen in the application
Table :- tables_info
Contents of a record :- what is the format of a column of a table that needs to be displayed such as heading , data-type , textbox/listbox etc. , needs to be presented in presentable version , width
I was thinking for a java solution and use XML instead of database presentation tables. There will be multiple XSL and XML for this presentation info.
I need to justify this approach to my colleagues.
Here are some points:
FOR -->
1. Database is not a good way for storing presentation info. whereas XML is
2. Later on we can change it easily if required as well as talk more effectively with other applications ( which is our need in near future )
3. For each screen load and reload , we need not access database presentation tables. Improves performance
Against -->
1. It's fine for saying not to store the data in database , but ultimately we have to access the XML and the files etc.
2. I am planning to use XSQL servlet from Oracle that basically will handle the query execution part and return a proper output as I am going to specify with a stylesheet
This poses a danger in case tomorrow we plan to deal with some other database than Oracle. So instead of that I can go for java beans and XMl parsers.
I am not able to exactly specify the advantages of storing presentation info. in XML.
Please guide me and correct if I am wrong. I badly need help on this decision.
Thanks
-kg

Hi Steve,
That's a good point.
Related question is as I am going to use XSQL servlet, if we shift tomorrow some other database than oracle , XSQL servlet is of no use I guess and I should go for parsing and all by myself. Isn't it?
But can you tell me the major advantages of using XML in my case?
Thanks-
Kirti

K9A2 plat hardware, CPU monitoring-advice needed please

Hi,
It seems that the MSI's "dualcore center" does not accurately displays CPU temp, normally it shows CPU temp. at lower than room temp.
Also sometimes dual-core-center freeze/hangup other programs as well.
With that being said, I am looking for advice/recommendation as to what program to use to monitor CPU temps; something that would show in the task bar, show current temp., and does not hog up lot of resources.
thanks

Oh yes... got to pay more attention to the spell checker.
Ironic.... I come here for technical advice and I get a lesson in spelling. thanks Frankenputer. Furthermore ironic the fact is that I claim that I am not obsessed, yet I keep coming back here too read /learn more. May be it is not an obsession but an addiction. I am just a newbie here, some of you have post count above 1K. Hee-heeee..
Fredric, you mention bios is the most accurate, but you can't access it during a game play or application use.
The only time I see bios info is when I boot. (yes boot no need to correct.... boot= as in pressing the power "ON" button to begin PC operation) it would not be a good monitoring tool.
Hans
There is room , I am just not satisfied the way it is mounted. A huge, heavy heatsink hanging out to the side which is supported by the MOBO, now you hang another object(fan) on the heatsink; just like hanging weight on the end of a lever. Then you spin up the fan and let it vibrate, these cheap fans not balanced as they should be. An air tunnel or duct system would be a much better way to bring airflow to a heat sink, better than hanging a fan on it.
Normal way of mounting works of course. I am just testing to see if there is a better way. I am using a fan, just mounting it elsewhere.
Products engineered certain way because size, cost, or compatibility issues. Not necessarily to be most efficient.
My corsair TX750 PSU a good example. A fan is mounted inside; size and compability issue.
So the engineers put a 140 mm fan on the bottom(inside), blocked half of its airflow with a plastic shield so air is moved to the back, though and out.
I removed the fan and the airflow blocking plastic piece, mounted fan on outside of PSU. Airflow has nearly doubled. I am sure it runs cooler too. A slight mod to the case was necessary. Now I sleep better at night (kiddding)
This PSU (unmodified) in an Antec P182 case barely moved any air through it. I ended up selling the the antec 182.

Some advice needed Please Quicksilver 800MHZ

Similar Messages

Maybe you are looking for