Some audio questions (connection to stereo and streaming audio)

1) Whats the best way to connect my stereo? Rught now I am using 1/8" from the headphone jack to the RCA jacks on my stereo. Is there a better way ( I see on the apple store site some type of monster cable that looks like it may perform a similar function). My stereo is older, so there is no optical line in or out.
2) Whats the best way to capture streaming audio ? Ive downloaded trial versions of sound studio, audio hijack, and irecord, but havent had any luck. Is there some special type of hardware configuration I need to do? The sources I am streaming from are dead.net and archive.org
Thanks

The optical sould out is far far better than the headphone out. My sound system is old but I use the MD player as an analogue /digital converter. If you dont have an MD player with this option you need to find an analogue /digital converter. There are loads on the market. You will hear the difference.
For recording streamed sounds I use Audio Highjack. The most important thing you need to do is create a source for each program you want to record from. I record the BBC so I created a source in Highjack (left window in the record prefs) for Safari. If I want to record from
the other progs I have to do the same for them.

Similar Messages

Question about networking iMac and streaming video to TV

I have the 24" iMac 2.66GHz with 4 G ram. Currently using Motorola SBG900 (Docsis 2) cable modem & router to stream Comcast through house (another PC, iPhones, LG Blu Ray player/digital video streamer).
Recently acquired a Netgear Rangemax 3700 which is supposed to be the fastest current wireless router. Here are my questions:
1) Can I just use the Motorola SBG900 as modem ONLY and run the ethernet out of it to the Netgear router (thus bypassing the router built into the SBG900). Will this accelerate the streaming of video to other receivers?
2) Would I be better off with a Motorola 6120 Docsis 3 Cable modem feeding the Netgear router (even though my Comcast cable feed is Docsis 2, not 3)?
3) Since my Comcast account is rated 10 Mbps max (though it sometimes goes up to 15 or so late at night) and I believe the existing Motorola SBG90 is rated at 54 Mbps, is the limiting factor the speed of my Comcast connection and all else doesn't matter? That is, is it impossible to speed up my streaming or download speed without a faster connection to the Internet?
4) What kinds of connections are there that are faster than Comcast cable connections?
Basically, I don't want to waste money or time if I'm already at the maximum throughput available given my connection. If I can get marginal speed increases by adding new modem and router, that's fine. I'll do that.
Thanks for your help.
PS: I owned and returned the Airport Extreme Base Station. It did not increase the speed of my connection or streaming, but then it tested very poorly at www.smallnetbuilder.com -- about half the speed of the Netgear Rangemax.

Can't help with Q 1 + 2, but here are some things to consider re:
+3) Since my Comcast account is rated 10 Mbps max (though it sometimes goes up to 15 or so late at night) and I believe the existing Motorola SBG90 is rated at 54 Mbps, is the limiting factor the speed of my Comcast connection and all else doesn't matter? That is, is it impossible to speed up my streaming or download speed without a faster connection to the Internet?+
My Comcast account is rated 15 Mbps and I never get that. I've done everything I can here including Cat 6 cables (instead of Cat 5), but the major problem/hangup in my case is: Comcast is using 20-year old buried cables from their hub (approx. 10 mi across town) to the neighborhoods here - those cables are "leftovers" from the company Comcast purchased the rights from. So, we not only have old cables, but the little boxes all over the neighborhood feed at least 6 - 10 homes each, so you are sharing the available bandwidth with the neighbors. And, whenever everyone seems to be online at the same time, my downloads slow down to a c r a w l (as slow or slower than dialup occasionally!).
So, unless you have a better/newer cable setup where you are, you need to keep that in mind; in that case, no matter what you do, you are at the mercy of Comcast's equipment and your neighbors' usage.
4) The only one I know of is FioS (fiber optic).

Some basic question of Airport Extreme and Airport Express

As I know, my G4PB is installed Airport Extreme and it seems like working wireless Internet connection during travel. But which case do I need additional things like Airport Express (if I undestand this wireless technology correctly)?

blue sky,If all really depends on what you are trying to achieve.
If you wish to surf the Internet when you're out and about then you can just walk in to Starbucks, for example, and log-in - you already have all that is required.
If you want to use the Internet wirelessly at home then the Apple Extreme Base Station, an Airport Express or much cheaper 3rd party gear can help (although some additional hardware may be required dependimg on how you connect to the Internet).
If you want to surf wirelessly, stream music from iTunes to your home Hi-Fi and use a USB printer wirelessly then the Airport Express is the puppy.
If you need to share an Internet connection as well as a network with many wired and wireless users then the Airport Extreme Base Station could help.
Try reading the Airport Page to consolidate your ideas of what you want to achieve, or use this home networking wizard.
Either way you should be aware that you don't have a Powerbook Titanium (On a Ti the ports are tidy on the back under a neat cover and it has a slim 1" thin design) but rather you have a PB Aluminium (ports scattered on either side and it's approx 1.25" thick!)
mrtotes

We have an airport extreme wifi in house, but also want to set up a hardwired ethernet connection for gaming and streaming of netflix. The computer only sees one or the other not both at same time.

We have a new iMac 2.9ghz and are running an airport extreme set up in house with several express entenders. The problem is that our son is streaming netflix and doing on line gaming and hogging all the band width. Time Warner tech suggested a hard wired ethernet connection to computer base sattion next to computer so that it can have direct conenction to internet. After much fishing of wire the connection worked great, but the wifi connection for the house is gone. I unplugged the ethernet connection and everything is fine. I read the articles about adjusting network preferences, but the issue seems to be in the extreme not in the computer. the connection goes from cable modem to extreme, from extreme to house and to hard wired conenction to other computer. Do we need a splitter before the extreme?

No. Something else is going on.
Your son may be hogging all the bandwidth but your wireless network should never simply disappear. Moreover, if your son isn't doing anything the available bandwidth for other devices should remain unaffected.
I suspect that something is miswired, and from what you describe I suspect that link is between the Extreme and the "other computer".
The way to accomplish what you propose is
Modem > Ethernet cable to Extreme's WAN port
Extreme's LAN ports > wired Ethernet devices.
There should be nothing but an Ethernet cable linking an Extreme LAN port and any other wired device. If you run out of available LAN ports on the Extreme, you need to by an "Ethernet switch" - they are not expensive, but don't call it a "splitter" or you will only confuse yourself. The switch would be connected to one of the Extreme's LAN ports, and you would connect additional devices to it. You can also use one of your Expresses for that purpose, assuming it is the current generation model with two Ethernet ports.

Some basic questions about foriegn key , and relationships.

Hi
Thank you for reading my post
I read some documents about foreugn key and tables relation ships.
but i still can not understnad some stuff.
1-when we have a foreign key , we have two tables that we want to relate them together
in a way that one of ? table columns forced to be a value from ?? table column.
what is name of those two tables , i saw , child-parent , ..... which confuse me.
can some one please tell me correct name of those two tables ?
2-some times we need some kind of master details relation like :
one-to-many : i this case MANY table will have a column to point a record in ONE table , can this relation be a foreign key relation ?
3-we can achieve many-to-many relation only by using a helper table to host both tables primary keys in a record to relate them together.
can you point me to some resources that help me to find answers to this questions ?
or explain them to me ?
thank you for your time.

These are critical database basics that you need to understand. I would seriously recommend getting some study in, because proper relational database design relies on the basic principle of data and relationships and a process called normalization.
In reality, you only really need one gigantic table to host data. It would include everything you would want to know about something - let's take a sales order for example. You would have to record the customer's name, address, etc. along with every item they ordered, etc. You would have a HUGE table full of data that appeared over and over and over again. This is bad design for two basic reasons: it is difficult to query, and it is very easy to have minor mistakes like capitalization or alternate spellings that prevent things from matching up properly. For example, let's say Bob orders 40 widgets and 40 digits. In our hypothetical table, we could put it in as Bob - 40 widgets and Robert - 40 digits. See how confusing this can get even in a simple example? And let's say you wanted to correct all of Robert's orders to say Bob and you found out there were 40 orders from "Robert" How would you know which ones to change?
The process of normalization helps to reduce the chance for these types of errors in addition to creating a good basis for indexes. You normalize the data by creating sets of parent/child tables with a "key" value to match them. In our hypothetical situation, you could create a table for orders and a table for customers. In the customers table you give all the detail for the customer in one place, and you assign each customer a unique number or ID. In the orders table we add the customer ID (NOT the name) and we ensure that we are getting the customer we want, in addition to saving a lot of space and eliminating redundancy. In our example, the customers table is the "parent" table and the orders table is the "child" table. The child table references the unique entries in the parent table via that id. That reference is referred to as a foreign key. The foreign key in the child table points back to the original and complete record in the parent table and eliminates the redundancy of keeping all that extra data for every order. Foreign keys in child tables always refer to a primary/unique key in the parent field.
That help?

Q: Re: Q: Acquiring data using two E series devices connected by RTSI and streaming data to disk

<< (My first posting)
I use two E series PCI Cards, connected by RTSI. I'd like to stream the data
from both cards to a binary file and to add a header to it.
I also need to somehow read (plot) the stored data, this with another VI.
The whole should be then integrated into an existing program, that used just
one acquisition card.
Till now I have tried to combine "Two E-series Shared ScanClk.vi" and "High
Speed Data Logger.vi" into another VI, and I have tried to read the stored
data with the "High Speed Data Reader.vi". The problem is that I fight with
one error after another, what prevents me from going further.
I use LabView 6.1, under Windows 2K.
Has somebody by chance already done something similar and would agree to
share with me their experience? TIA for any suggestion.
Regards,
Victor Manta
>>
"Ben" wrote in message
news:[email protected]...
> Hi Victor,
>
> I have done a lot of similar work.
>
> Exactly what did you try and what specific errors did you encounter?
>
> What you are trying is do-able provided the hardware you have suuports
> it.
>
> Please post (both here and to the DAQ group)
> the details of the hardware you are using,
> versions of software being used,
> Examples that you are using,
> error codes that occured,
> posibly post example code showing the problem.
>
> Ben
Hi Ben,
I use two PCI-MIO-16E-1 cards, connected by RTSI. I'd like to stream the
data from both cards in real time to a binary file, after having added a
header to it.
For tests, on the channel 0 of each card is applied the same square wave,
100 Hz.
Yes, the hardware support RTSI. I use LabView 6.1.
Till now I have:
1. Combined the "Two E-series Shared ScanClk.vi" and the "High
Speed Data Logger.vi" into a DAQ VI. To do this, I have "doubled" and
adapted the "High Speed Data Logger.vi". For testing purposes the data are
stored in two files, always the same ones (the old ones being overwritten
after each acquisition).
2. "Doubled" and adapted "High Speed Data Reader.vi" into another VI, for
reading from both files, mentioned earlier.
What already works:
- The headers for both files are correctly stored (VI point 1.)
- The acquired data from the first card (device 1) are correctly stored (VI
point 1.)
- The VI (point 2.) that reads both files and displays the results works
What doesn't work:
- The acquired data from the second card aren't stored at all (VI point 1.)
- An error message says: "Error -10608 occurred at AI Buffer Read. Possible
reason: NI-DAQ LV: No transfer is in progress for the specified resource."
I think that I understand this message, but I don't know how to continue.
The DAQ VI can be downloaded from (please click the link, then the link on
that page; about 100K, zipped):
http://www.swissheartnet.unibe.ch/labview.htm
Thanks a lot in advance.
Regards,
Victor Manta
PS. I don't know which DAQ group you mean.

"Filipe A." wrote in message
news:[email protected]...
> Victor;
>
> You can definitely accomplish that task with the DAQ boards you have
> and Labview.
>
> It would be good if you could be more specific as far as what type of
> errors you are seeing and how you are integrating both VIs.
>
> Regards
> Filipe A.
> Applications Engineer
> National Instruments
Maybe Mr. Filipe A. could help me? Please see below, and TIA.
Regards,
Victor Manta
"Victor Manta" wrote in message
news:[email protected]...
> << (My first posting)
> I use two E series PCI Cards, connected by RTSI. I'd like to stream the
data
> from both cards to a binary file and to add a header to it.
>
> I also need to somehow read (plot) the stored data, this with another VI.
>
> The whole should be then integrated into an existing program, that used
just
> one acquisition card.
>
> Till now I have tried to combine "Two E-series Shared ScanClk.vi" and
"High
> Speed Data Logger.vi" into another VI, and I have tried to read the stored
> data with the "High Speed Data Reader.vi". The problem is that I fight
with
> one error after another, what prevents me from going further.
>
> I use LabView 6.1, under Windows 2K.
>
> Has somebody by chance already done something similar and would agree to
> share with me their experience? TIA for any suggestion.
>
> Regards,
> Victor Manta
> >>
>
> "Ben" wrote in message
> news:[email protected]...
> > Hi Victor,
> >
> > I have done a lot of similar work.
> >
> > Exactly what did you try and what specific errors did you encounter?
> >
> > What you are trying is do-able provided the hardware you have suuports
> > it.
> >
> > Please post (both here and to the DAQ group)
> > the details of the hardware you are using,
> > versions of software being used,
> > Examples that you are using,
> > error codes that occured,
> > posibly post example code showing the problem.
> >
> > Ben
>
> Hi Ben,
>
> I use two PCI-MIO-16E-1 cards, connected by RTSI. I'd like to stream the
> data from both cards in real time to a binary file, after having added a
> header to it.
>
> For tests, on the channel 0 of each card is applied the same square wave,
> 100 Hz.
>
> Yes, the hardware support RTSI. I use LabView 6.1.
>
> Till now I have:
>
> 1. Combined the "Two E-series Shared ScanClk.vi" and the "High
> Speed Data Logger.vi" into a DAQ VI. To do this, I have "doubled" and
> adapted the "High Speed Data Logger.vi". For testing purposes the data are
> stored in two files, always the same ones (the old ones being overwritten
> after each acquisition).
>
> 2. "Doubled" and adapted "High Speed Data Reader.vi" into another VI, for
> reading from both files, mentioned earlier.
>
> What already works:
>
> - The headers for both files are correctly stored (VI point 1.)
> - The acquired data from the first card (device 1) are correctly stored
(VI
> point 1.)
> - The VI (point 2.) that reads both files and displays the results works
>
> What doesn't work:
>
> - The acquired data from the second card aren't stored at all (VI point
1.)
> - An error message says: "Error -10608 occurred at AI Buffer Read.
Possible
> reason: NI-DAQ LV: No transfer is in progress for the specified resource."
>
> I think that I understand this message, but I don't know how to continue.
>
> The DAQ VI can be downloaded from (please click the link, then the link on
> that page; about 100K, zipped):
>
> http://www.swissheartnet.unibe.ch/labview.htm
>
> Thanks a lot in advance.
>
> Regards,
>
> Victor Manta
>
> PS. I don't know which DAQ group you mean.

Q: Acquiring data using two E series devices connected by RTSI and streaming data to disk

I use two E series PCI Cards, connected by RTSI. I'd like to stream the data
from both cards to a binary file and to add a header to it.
I also need to somehow read (plot) the stored data, this with another VI.
The whole should be then integrated into an existing program, that used just
one acquisition card.
Till now I have tried to combine "Two E-series Shared ScanClk.vi" and "High
Speed Data Logger.vi" into another VI, and I have tried to read the stored
data with the "High Speed Data Reader.vi". The problem is that I fight with
one error after another, what prevents me from going further.
I use LabView 6.1, under Windows 2K.
Has somebody by chance already done something simi
lar and would agree to
share with me their experience? TIA for any suggestion.
Regards,
Victor Manta

<< (My first posting)
I use two E series PCI Cards, connected by RTSI. I'd like to stream the data
from both cards to a binary file and to add a header to it.
I also need to somehow read (plot) the stored data, this with another VI.
The whole should be then integrated into an existing program, that used just
one acquisition card.
Till now I have tried to combine "Two E-series Shared ScanClk.vi" and "High
Speed Data Logger.vi" into another VI, and I have tried to read the stored
data with the "High Speed Data Reader.vi". The problem is that I fight with
one error after another, what prevents me from going further.
I use LabView 6.1, under Windows 2K.
Has somebody by chance already done something similar and would agree to
share with me their experience? TIA for any suggestion.
Regards,
Victor Manta
>>
"Ben" wrote in message
news:[email protected]...
> Hi Victor,
>
> I have done a lot of similar work.
>
> Exactly what did you try and what specific errors did you encounter?
>
> What you are trying is do-able provided the hardware you have suuports
> it.
>
> Please post (both here and to the DAQ group)
> the details of the hardware you are using,
> versions of software being used,
> Examples that you are using,
> error codes that occured,
> posibly post example code showing the problem.
>
> Ben
Hi Ben,
I use two PCI-MIO-16E-1 cards, connected by RTSI. I'd like to stream the
data from both cards in real time to a binary file, after having added a
header to it.
For tests, on the channel 0 of each card is applied the same square wave,
100 Hz.
Yes, the hardware support RTSI. I use LabView 6.1.
Till now I have:
1. Combined the "Two E-series Shared ScanClk.vi" and the "High
Speed Data Logger.vi" into a DAQ VI. To do this, I have "doubled" and
adapted the "High Speed Data Logger.vi". For testing purposes the data are
stored in two files, always the same ones (the old ones being overwritten
after each acquisition).
2. "Doubled" and adapted "High Speed Data Reader.vi" into another VI, for
reading from both files, mentioned earlier.
What already works:
- The headers for both files are correctly stored (VI point 1.)
- The acquired data from the first card (device 1) are correctly stored (VI
point 1.)
- The VI (point 2.) that reads both files and displays the results works
What doesn't work:
- The acquired data from the second card aren't stored at all (VI point 1.)
- An error message says: "Error -10608 occurred at AI Buffer Read. Possible
reason: NI-DAQ LV: No transfer is in progress for the specified resource."
I think that I understand this message, but I don't know how to continue.
The DAQ VI can be downloaded from (please click the link, then the link on
that page; about 100K, zipped):
http://www.swissheartnet.unibe.ch/labview.htm
Thanks a lot in advance.
Regards,
Victor Manta
PS. I don't know which DAQ group you mean.

2 Questions ~ connecting the telephone and microfi...

Q1. Can I assume my telephone & answer machine can somehow be connected to the new Infinity wiring? Currently I have an extension cable between the BT Master socket in the hall and my study: the cable terminates at the micro filter and then one cable goes to the BT Hub and the other connects to the answer machine which in turn connected to the telephone.
Q2. Once BT Infinity is installed will I still need to keep the microfilters I have connected to the other BT sockets around the house?
Solved!
Go to Solution.

Basically the guy will install a new master socket, that has a new infinity modem plugged into at (at the master socket). That modem NEEDS a power supply ( so youll need one next to the master socket)
The engineer then lays a special cable from that modem directly to where you want the hub situated.
Any phone or phones you got plug into the main phone socket as per usual

Still have some configuration questions for SSD/HDDs and Pr Pro (laptop)

Hi guys,
So I recently asked a question regarding configurations for a new Toshiba Qosmio (being delivered in 2 days) I've done a lot of reading and have become somewhat more educated and somewhat more confused. I'm having the X70-ABT3G22 custom built with an i7-4700MQ, a 256GB mSATA SSD, 2 matching 500GB (7200rpm Serial-ATA) HDDs, a 3GB GeForce GTX 770M, and 32GB DDR3L 1600MHZ SDRAM.
It was suggested that I RAID 0 the 2 HDDs, which sounds like a great idea. My question then, is the configuration of Premiere Pro with the - now 2 drives left. I was reading about disk set-up on http://ppbm7.com/index.php/tweakers-page/84-disk-setup/95-disk-setup which was very informative. But the information there suggests that if I have 2 drives, I should consider adding a 3rd.
At this point, there's no room for a third internal drive because the 2 have been striped to make 1, The SSD is obviosly for the OS and programs. And if Premier Pro functions more efficiently by spreading the workload over at least 3 disks, would I be better off by not striping the 2 matching HDDs and spreading the workload out? Or should I stripe the 2 internal drives and use a USB 3.0 flash drive for the previews, media cache, or exports? Or stripe the 2 HDDs and just work with the 2 internal drives without anything external? I'm looking for suggestions from you guys for the best way to configure this particular set-up. Any help would be greatly appreciated. Serioulsy.
Thanks again
Todd

I do not know if a USB3 RAID box would be any better than my simple experiment that I tried. See my thread for item 2 in the first post. I bought a 2 1/2" external enclosure which I researched extensively for what sounded like it had an optimized SATA III to USB3 interface. I put one of the fastest SSD drives I am aware of (Samsung 840 Pro 256 GB) in it to see what the performance would be. When I put this SSD in my laptop directly on an internal SATA III with my PPBM6/7 benchmark it gives me a Premiere write transfer rate of almost 500 MB/second. When I put the same drive in the external USB3 enclosure the Premiere write transfer is limited to slightly less than 200 MB/second which probably better than a most hard disk drives, but now where near taking advantage of the speed capability.
The answer to your question is yes, you can use an external hard drive RAID enclosure effectively but do not expect much more speed from that device. You will have more reliability if you set it up for the right RAID mode. Using hard drives you will have much greater capacity than SSD's offer. The only disadvantages with a large multidisk USB3 enclosure is you will always have to have another AC cord to plugin and dragging a large disk enclosure around is a pain. The small 2 1/2" enclosure above is self powered and highly portable.
Do not believe many of the advertised read/write rates of these USB3 devices, specifically the write rates are not what you can achive in real life applications.
I just checked and your Toshiba laptop does not have eSATA so I think you are limited to only USB3 peripherals.

I have some Iphone questions, reguarding the original and plans.

So say I buy an original Iphone, could I simply put my sim card in the phone, but an unlimited data plan and feel free to use 3g as I want to?
Or do I have to unlock the phone to do this?

Sorry, meant Edge.
So I'm basically asking, I don't need a seperate plan to get Edge access, correct?
I can just add a data plan to my family plan?

Some basic questions on Java development and NetWeaver CE

Hi there,
Can someone please explain for me:
1. What are the development tools that will help me do Java development in SAP?
2. Can I use non-SAP Java development tools (e.g. WebSphere or Eclipse) to develop custom extensions? Are these equivalent to the functionality provided by CE?
3. Given the options for doing Java development in SAP, are there any situations where I would need to do custom development in ABAP? (Is the Java functionality equivalent to the ABAP functionality?)
4. Is NetWeaver CE only meant for Java development, or can it also be used for ABAP development?
regards,
Eric

Hi
for Java development you can user Eclipse or NWDS , which are both and the same .
And about the ABAP development in CE 7.1 in the developer studio is it not possible .
you are allowed for the java development . And about using Non-SAP java development tools
you can use the tools for java development , may the UI building ..... has to be build when compared to
CE 7.1 developer studio
Developer Studio for ABAP
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/7ef5ad90-0201-0010-b2b5-b112ca87e421
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/100dac80-f93c-2a10-15a1-a9ac1fd3166c
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/40af00ad-8080-2a10-88b5-cc4cec99d8ac
Thanks

Sample questions for KMC-1 and KMC-2

Hi All,
I am preparing for SAP EP 7.0 Certification. Can someone provide mw with some sample questions of KMC-1 and KMC-2.
Points assured.
Regards
Nikhil

Hi Nikhil ,
Hi,
Look at this thread and you may also refer to these links
<b>https://forums.sdn.sap.com/thread.jspa?threadID=404007
https://www.sdn.sap.com/irj/sdn/thread?messageID=3418833#3418833</b>
Getting Started
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/webcontent/uuid/cacd8860-0a01-0010-a393-a7bdd1449487
eLearning sessions
https://www.sdn.sap.com/irj/sdn/km-elearning
KMC blogs
https://www.sdn.sap.com/irj/sdn/weblogs?blog=/weblogs/topic/17
KMC developer area.
https://www.sdn.sap.com/irj/sdn/km
http://help.sap.com/saphelp_nw04/helpdata/en/4c/9d953fc405330ee10000000a114084/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/1d/3d59fdaa5ebb45967ea107d3fa117a/frameset.htm
Thanx
Pankaj

Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear-) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay

Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear…) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay to my Ipad. My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library? I`d appreciate any help. Alex.

My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library?
On the iPad you can stream videos, photos, or music from the Video, Photos, Music, and YouTube apps to an Apple TV OR just stream music to an AirPort Express Base Station.

I need to upgrade my 10.5.1 os on my G4/1.25 (I'm having some audio-midi setup problems), but it's a machine that is not connected to the internet. Do I have any options? Thanks!

Friends,
I'm having some audio-midi setup problems on my G4/1.25/10.5.1 machine. I'm thinking that a routine OS upgrade might help. However, this machine is not connected to the internet. Are there any alternate methods for upgrading system software? Thanks in advance!

OK, what you should do is download the updates on another machine and burn them to a disc. Start at this link http://support.apple.com/downloads/#leopard for downloads and find, among other things, the 10.5.8 combo updater that works on PPC machines, plus security, QuickTime and other updates. Going from 10.5.1 to 10.5.8, there will probably be a bunch of things that you should install. Being off the internet with the machine, you can't have Software Update sort it out, so something might get missed, unfortunately.
My suggestion is this: if it looks like you might need a download, get it onto that disc.

Question marks with some audio files

Hello all,
I've been trying to understand the problem I'm having with some audio files of my website, but to no avail. Some audio file are not loaded up with Quicktime, and only show a question mark with a blue "Q" around it.
In other words, would any of you be able to help me find out why the audio files in the following pages do not work:
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2007/4/7_Liszt_Sonata_in_B_minor%2C_S.2.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2006/6/23_Mozart_Piano_Concerto_in_C_minor%2C_K._491_i._All egro2.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2006/6/23_Mozart_Piano_Concerto_in_C_minor%2C_K._491_iii._A llegretto2.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2006/5/8_Bachs_Sarabande_from_Partita_no.2.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2004/8/6_Beethovens_Piano_Concerto_no._2_in_B-flat_major%2C _op._19_-_i._Allegro_conbrio.html
Although it does in these other pages:
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2007/10/29_Chopin_Etude_in_C_major%2C_op._10_no.1.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2007/9/18_Schubert_Piano_Sonata_in_E%2C_D_157_i._Allegro_ma _nontroppo.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2007/9/16_Schubert_Piano_Sonata_in_E%2C_D_157_ii.Andante.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2007/4/29_Beethoven_Piano_Sonata_in_C-sharp_minor_op._27_no ._2_-_i._Adagio_sostenuto2.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2004/6/8_Bach-Busoni_Chaconne_from_Partita_no._2%2C_BWV1004.html
http://sharon.barnea.free.fr/SharonBARNEA/Music/Entries/2004/6/8_Bach-Feinberg_Largo_from_Trio_Sonata_in_C_major%2C _BWV529.html
I really appreciate your help.

You are giving viewers the full title on your web page.
You could cut your files names like < Beethovens_Piano_Concerto_no._2_in_B-flat_major%2C_op._19_-_i._Allegro_conbrio.html >
to something like BthvnPC2BfM.
Publish to a folder and look in the "Media" folder to see that all your files are there.
A better way to provide a download is to ZIP the music file and link to it via "Link to: A file" in the Link Inspector.
Type "Download" over the file name that appears and select your rollover colors and U or not in the format page.

Some audio questions (connection to stereo and streaming audio)

Similar Messages

Maybe you are looking for