Something similar to "isdn network-failure-cause" command on Cisco 3600

Hi
I have two Cisco 3600 with NM-HDV-2E1 on each chassis. The version of ios is Version 12.3(19)
Sometimes the Cisco sends the 27 (Destination out of order) or the 38 (Network out of order) cause code, which is generally not correct, because most of all the problem of the traffic not passing is that there's no No circuit/channel available.
So I'd like that Cisco would send the 34 (No circuit/channel available) cause code instead of 27 and 38 cause codes.
Can anyone tell me how to do that?
Thanks in Advance.

Hi,
when the router makes confusion about the ISDN channels, you should first upgrade to latest maintenance and then if it happens again produce debugs to show what exactly the condition is, all failing the is matter for TAC because the router is supposed to send the correct cause code when no channels available.

Similar Messages

Can network setting cause sql*plus logon failure?

During install of verizon service the techs had to alter some network setting to allow the cable connection to work. Afterwards I was unable to connect to oracle database using pl*sql, getting instead an ORA 12514 error.
Is it possible the altered network settings caused this problem? I am running oracle 10g on XP windows.

1. you're not using pl*sql to connect. you're using SQLPLUS to connect.
2. ORA-12514: TNS:listener could not resolve SERVICE_NAME given in connect descriptor
so, verizon changed something, perhaps the "windows\system32\drivers\etc\hosts" file, so that now your TNSNAMES.ORA has the wrong info. check tnsnames.ora, and see if it's using machine name, IP, or "localhost", then give the new, correct info.

Cisco WAP 321 causes network failure ?

Hi everybody.
I recently bought a Cisco WAP 321 for my company, but when i connect it to the network, the switch on which I connect crashes, and I lose all connectivity to the network, (internet also). i have to unplug the WAP321 and wait for a few minutes to be able to use the network again.
I'm currently using a small 8 port switch, There are usually 3 or 4 users connected on it. When I try connecting the WAP321 on another switch, only connected to 1 computer, it seems to be working : I can access the configuration page, and make some modifications.
Has anyone had this problem already ?
Any idea ?
Thanks everybody for your time !

Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
Could you give a little more detail about your network? What is the switch that you are connecting to? The 8 port and the other one. A network topology would be helpful as well.
Thanks
Eric Moyers .:|:.:|:.
Cisco Small Business US STAC Advanced Support Engineer
CCNA, CCNA-Wireless
866-606-1866 ext 601027
Mon - Fri 09:00 - 18:00 (UTC - 05:00)
*Please rate the Post so other will know when an answer has been found.

Portal failed to access remote resource due to network failures

Hi,
We have a portlet that allows users to upload files to a SQL Server database and make it available for other users to access. The portlet code is on our remote servers. Everything works fine in dev environment, but certain files fail in pre-prod and prod within the portal, but work fine when the code is executed outside the portal.
I keep getting this error:
Error - Portal failed to access remote resource due to network failures. Try again later or contact your portal administrator.
What could the problem be?
Thank you for your help.
Rad

If the Studio service looks good on the remote server where Studio is installed (check that
the service is started and look in the Studio logs for any warnings or errors), you should
also verify the configuration settings in the Studio remote server object. Is it properly
configured and pointing to the correct remote server?
If so, check the portal servers access to the Studio server via the port specified in the remote
server (default is 11935). You can test this by doing a telnet test on the portal server. In a cmd
prompt (Windows) or on the CLI (Unix), type 'telnet [studioserver] 11935', where "<servername> is
the name of your Studio remote server. The screen should just go blank, meaning that there is
something accepting connections on that port on the given server. (We would hope it's the Studio
app and not another service occupying that port.) If you get "Could not open connection to the host"
or some such similar result, check that the network between the portal and the Studio remote server
is open (ie, make sure there isn't any port blocking or a firewall in place that would hinder the
communication between the two servers).

Oracle 10g CRS autorecovery from network failures - Solaris with IPMP

Hi all,
Just wondering if anyone has experience with a setup similar to mine. Let me first apologise for the lengthy introduction that follows >.<
A quick run-down of my implementation: Sun SPARC Solaris 10, Oracle CRS, ASM and RAC database patched to version 10.2.0.4 respectively, no third-party cluster software used for a 2-node cluster. Additionally, the SAN storage is attached directly with fiber cable to both servers, and the CRS files (OCR, voting disks) are always visible to the servers, there is no switch/hub between the server and the storage. There is IPMP configured for both the public and interconnect network devices. When performing the usual failover tests for IPMP, both the OS logs and the CRS logs show a failure detected, and a failover to the surviving network interface (on both the public and the private network devices).
For the private interconnect, when both of the network devices are disabled (by manually disconnecting the network cables), this results in the 2nd node rebooting, and the CRS process starting, but unable to synchronize with the 1st node (which is running fine the whole time). Further, when I look at the CRS logs, it is able to correctly identify all the OCR files and voting disks. When the network connectivity is restored, both the OS and CRS logs reflect this connection has been repaired. However, the CRS logs at this point still state that node 1 (which is running fine) is down, and the 2nd node attempts to join the cluster as the master node. When I manually run the 'crsctl stop crs' and 'crsctl start crs' commands, this results in a message stating that the node is going to be rebooted to ensure cluster integrity, and the 2nd node reboots, starts the CRS daemons again at startup, and joins the cluster normally.
For the public network, when the 2nd node is manually disconnected, the VIP is seen to not failover, and any attempts to connect to this node via the VIP result in a timeout. When connectivity is restored, as expected the OS and CRS logs acknowledge the recovery, and the VIP for node 2 automatically fails over, but the listener goes down as well. Using the 'srvctl start listener' command brings it up again, and everything is fine. During this whole process, the database instance runs fine on both nodes.
From the case studies above, I can see that the network failures are detected by the Oracle Clusterware, and a simple command run once this failure is repaired restores full functionality to the RAC database. However, is there anyway to automate this recovery, for the 2 cases stated above, so that there is no need for manual intervention by the DBAs? I was able to test case 2 (public network) with the Oracle document 805969.1 (VIP does not relocate back to the original node after public network problem is resolved), is there a similar workaround for the interconnect?
Any and all pointers would be appreciated, and again, sorry for the lengthy post.
Edited by: NS Selvam on 16-Dec-2009 20:36
changed some minor typos

hi
i ve given the shell script.i just need to run that i usually get the op like
[root@rac-1 Desktop]# sh iscsi-corntab.sh
Logging in to [iface: default, target: iqn.2010-02-23.de.sayantan-chakraborty:storage.disk1.amiens.sys1.xyz, portal: 192.168.181.10,3260]
Login to [iface: default, target: iqn.2010-02-23.de.sayantan-chakraborty:storage.disk1.amiens.sys1.xyz, portal: 192.168.181.10,3260]: successfulthe script contains :
iscsiadm -m node -T iqn.2010-02-23.de.sayantan-chakraborty:storage.disk1.amiens.sys1.xyz -p 192.168.181.10 -l
iscsiadm -m node -T iqn.2010-02-23.de.sayantan-chakraborty:storage.disk1.amiens.sys1.xyz -p 192.168.181.10 --op update -n node.startup -v automatic
(cd /dev/disk/by-path; ls -l *sayantan-chakraborty* | awk '{FS=" "; print $9 " " $10 " " $11}')
[root@rac-1 Desktop]# (cd /dev/disk/by-path; ls -l *sayantan-chakraborty* | awk '{FS=" "; print $9 " " $10 " " $11}')
ip-192.168.181.10:3260-iscsi-iqn.2010-02-23.de.sayantan-chakraborty:storage.disk1.amiens.sys1.xyz-lun-1 -> ../../sdc
[root@rac-1 Desktop]# can you post the oput of ls /dev/iscsi ??you may get like this:
[root@rac-1 Desktop]# ls /dev/iscsi
xyz
[root@rac-1 Desktop]#

APP-V 5 SP1 - "Application Failed to Launch. This may be due to a network failure 0x0FD01B25-0000007B"

Hello all,I am having some issues with APP-V 5.
I am having particular issues with starting a packaged SIMS.net. I keep recieving:
"Application Failed to Launch. This may be due to a network failure 0x0FD01B25-0000007B"
...within a second or two of clicking on the app-v created shortcut for this software.
To clarify, I had this software working perfectly previously. I recreated this package due to a software update, but it fails to launch now. I started a new package from scratch as this is a complex piece of software with multiple installers to run etc.
To be honest, I keep seeing this error on other applications. At one point, nearly every published app returned the same error. I spent a day trying to diagnose but the following day, everything mysteriously started working again.
I have had a look on kirks blog & Tim Magan, but to no avail.
Any help would be greatly appreciated, as this is a 'business critical application' (as they say).
Quick overview of my setup:
- Single Server configuration (Management, Publishing & SQL) on Server 2012 VM in 2012 Hyper-V
- Win 2000 Domain with 2003 DC
- Windows 7 Enterprise SP1
- SIMS.net Summer 2013 sequenced on 32bit following best practice guide
- Deploying to 32 bit machine
- Client settings pushed by GPO. Powershell execution policy set to allsigned.

RESOLVED: This error is caused by the "Program Files" missing from the "C:\ProgramData\Microsoft\Windows\Start Menu\" folder.
Firstly, a big thank you Nicke. You may not have solved the problem, but you sent me down the road to resolve this issue.
After trying the step you mentioned, I placed the computer in an OU with inheritance disabled. From this point onwards, I deduced that it was actually a group policy issue.
In my environment, I redirect start menus to generated start menu. This is created using a powershell script to combine locally installed items and network items. This scripts deletes the content of the 'programdata' start menu (i.e all users start menu)
to prevent these items disrupting the start menu.
Now... The app-v packages were breaking because, the 'Start Menu > Programs' folder did not exist. If an empty 'Start Menu > Programs' exists, the packages work correctly.
I can only assume that the two packages that were working correctly - that I installed these for 'current user only', rather than 'all users'.
It seems a little silly to me that app-v should fall over for something so simple. However, you could argue that it serves me right for playing about with system files :)
Thanks again for the help.
Mark

Cluster node reboots after network failure

hi all,
The suncluster 3.1 8/05 with 2 nodes (E2900) was working fine without any errors in the sccheck.
yesterday one node rebooted saying a network failure,errors in the massage file are
Jan 17 08:00:36 PRD in.mpathd[221]: [ID 594170 daemon.error] NIC failure detected on ce0 of group sc_ipmp0
Jan 17 08:00:36 PRD Cluster.PNM: [ID 890413 daemon.notice] sc_ipmp0: state transition from OK to DOWN.
Jan 17 08:00:47 PRD Cluster.RGM.rgmd: [ID 784560 daemon.notice] resource PROD status on node PRD change to R_FM_DEGRADED
Jan 17 08:00:47 PRD Cluster.RGM.rgmd: [ID 922363 daemon.notice] resource PROD status msg on node PRD change to <IPMP Failure.>
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 529407 daemon.notice] resource group CFS state on node PRD change to RG_PENDING_OFFLINE
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource PROD state on node PRD change to R_MON_STOPPING
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 707948 daemon.notice] launching method <hafoip_monitor_stop> for resource <PROD>, resource group <CFS>, timeout <300> seconds
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 736390 daemon.notice] method <hafoip_monitor_stop> completed successfully for resource <PROD>, resource group <CFS>, time used: 0% of timeout <300 seconds>
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource PROD state on node PRD change to R_ONLINE_UNMON
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 443746 daemon.notice] resource PROD state on node PRD change to R_STOPPING
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 707948 daemon.notice] launching method <hafoip_stop> for resource <PROD>, resource group <CFS>, timeout <300> seconds
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 784560 daemon.notice] resource PROD status on node PRD change to R_FM_UNKNOWN
Jan 17 08:00:50 PRD Cluster.RGM.rgmd: [ID 922363 daemon.notice] resource PROD status msg on node PRD change to <Stopping>
Jan 17 08:00:51 PRD ip: [ID 678092 kern.notice] TCP_IOC_ABORT_CONN: local = 172.016.005.025:0, remote = 000.000.000.000:0, start = -2, end = 6
Jan 17 08:00:51 PRD ip: [ID 302654 kern.notice] TCP_IOC_ABORT_CONN: aborted 53 connections
what can be the reason for reabooting?
is there any way to avoid this, with only a failover?
rgds
Message was edited by:
suj

What is in that resource group? The cause is probably something with Failover_mode=HARD set. Check the manual reference section for this. The option would be to set the Failover_mode=SOFT.
Tim
---

Ntrights.exe Windows 2008 R2 Resource Kit Tool? Does it exist or is there something similar I can use?

I am running Windows Server 2008 R2 Standard as a DC
I am trying to add users/groups to the following local policies through a GPO, however I need to script it out using something similar to ntrights.exe. I do not want to do it through the GUI because this is going to be a re-occurring process.
Below are the policies I am trying to configure via some kind of command prompt. I do not think I can do this with PowerShell 2.0 even with the import-module grouppolicy cmdlets.
Computer Configuration\Policies\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Allow log on locally
Computer Configuration\Policies\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Debug programs
Computer Configuration\Policies\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Force shutdown from a remote system
Computer Configuration\Policies\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Shut down the system
Computer Configuration\Policies\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Change the system time
Computer Configuration\Policies\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Allow logon through Remote Desktop Services
Would it be safe to copy the Windows Server 2003 ntrights.exe resource kit tool and try it on Windows Server 2008 R2? I am working on a virtual test lab environment so I can actually take a snapshot before hand but wanted your expert thoughts on it first.
Thank you in advance.

I found the solution.....You can actually use "quoted" host names in the templates instead of the SIDs. Make sure that for Domain User Accounts you specify the Domain prefix. For Local User accounts you can just specify the local user name.
The filename of the template that I made is LOCAL_SEC_TEMPLATE.inf
Here's what's inside that LOCAL_SEC_TEMPLATE.inf template:
[Unicode]
Unicode=yes
[Registry Values]
[Privilege Rights]
SeInteractiveLogonRight = "Administrators","XXDIGIHD\DigiOps","XXDIGIHD\Domain Admins"
SeDebugPrivilege = "Administrators","XXDIGIHD\DigiOps","XXDIGIHD\Domain Admins"
SeRemoteShutdownPrivilege = "Administrators","XXDIGIHD\DigiOps","XXDIGIHD\Domain Admins"
SeSystemtimePrivilege = "Administrators","XXDIGIHD\DigiOps","XXDIGIHD\Domain Admins","LOCAL SERVICE"
SeShutdownPrivilege = "Administrators","XXDIGIHD\DigiOps","XXDIGIHD\Domain Admins"
SeRemoteInteractiveLogonRight = "Administrators","XXDIGIHD\DigiOps","XXDIGIHD\Domain Admins","Remote Desktop Users"
[Version]
signature="$CHICAGO$"
Revision=1
[Profile Description]
Description=Local Security Template
Here's how I applied the template to the Local Security Policy: (You can use PowerShell or the regular command prompt)
SECEDIT /configure /db secedit.sdb /cfg "c:\LOCAL_SEC_TEMPLATE.inf"
Here's the link on using SECEDIT >> http://www.appdeploy.com/tips/detail.asp?id=23
Thanks for your help Gunter, this issue is solved.

Upload has failed. Network failure

Hello.
Since i work with indesign cc, i have a trouble wit folio builder panel: Everytime the upload fails at first attempt, it appears this message:"Upload has failed. Network failure." Ever works when i retried, but not at first attempts. This is unworkable with large publications, with a lot of articles. I´ve wrote that this is a trouble with the acrobat.com service outage, i need a solution.
Thanks. Best regards.

Was successfully re-linking indesign files to my dps producer dashboard. Files had been converted to CC (from CS6)-- and was switching from v26 to v 28. Everything was working just FINE, until about 6pm yesterday-- I had re-linked almost 3/4ths of my files, then I began getting the NETWORK FAILURE notice.
This morning, I tried creating a new folio-- managed to upload ONE new file into the new folio, then got the same 'network failure' message on the next one I tried to upload.
These files are from a successful app-- already in the app store, but it sure doesn't work right now! IOS 7 ... #!#*?
It is not about where your files are-- or how much memory -- Something else is going on.
I know you guys will figure it out...and will be standing by, anxious to fix my app!
THANKS.
nancy p

How to have a runtime error or failure cause all executions to stop and cleanup

I am using batch parallel mode. It's easy enough to terminate or abort all executions from SequenceFilePostStepRuntimeError using IEngine.TerminateAll() and .AbortAll(), but I would like to be able to set an error on all my running executions and cause them to run cleanup when I encounter an error on ANY of the test socket executions.
Anyone have an example of how I might do this?
Thanks,
Jake

I did something like this for a failure handler once... and looking through my code I think the biggest headache is to realize that one execution socket has no easy way of seeing the execution references for other sockets. These things are kept by the process model's top level execution... which you also don't have a super easy time accessing without tweaking some logic in your Model file.
(1)Somehow or another you want to get access to the "TestUUTs"/"SinglePass" Fileglobals.TestSocketExecutions[] array and make use of it in your classic RuntimeError callback. The easiest solution (but not the most elegant) would be to edit your model to copy/clone the file global into someplace more convenient... ie "TestUUTs - TestSocketEntrypoint".
(2) in your error callback, handle your error as usual i.e. tell top level sequence to go to cleanup etc. but also loop through the other execution references and do some variation on GetSequenceContext() and setting Runstate.sequenceErrorCode and the rest. The example api calls below are probably overkill...
Locals.currentExeContext=Locals.currentexecution.AsExecution.GetThread(0).GetSequenceContext(0, Nothing)
Locals.currentExeContext.AsSequenceContext.SequenceErrorCode=Locals.RecievedError.Code,
Locals.currentExeContext.AsSequenceContext.SequenceErroroccurred=Locals.RecievedError.Occurred,
Locals.currentExeContext.AsSequenceContext.SequenceErrorMessage=Locals.RecievedError.Msg,
Locals.currentExeContext.AsSequenceContext.ErrorReported =True, Locals.currentExeContext.AsSequenceContext.GotoCleanup =True
I'm using "Locals.RecievedError" as my error buffer in this case because it made sense to me to modifiy the error text to include which socket actually had the error (since now it's propigated to all sockets).
Locals.RecievedError.Msg=Parameters.Step.Result.error.msg+" Occurred on Socket#"+Str(RunState.TestSockets.MyIndex)
or something like that...
Was this what you were looking for? If you're really stumped and can tell me what version of TS you're using, I'll try and extract an example from my old code that you can use, but hopefully this helps.
Cheers,
Elaine R.
www.bloomy.com

How do I use 'Terminal' or something similar to Tether my Galaxy Phone

How do I use 'Terminal' or something similar to Tether my Galaxy [Note 1] Phone to my Macbook Pro in such a way that the Android phone gets my mac on the internet.
If it's possible for FREE then I can probably do that.
I try using the "Play" Store icon on the phone & it says 'No connection'.
Having a Macbook and not get internet is VERY frustrating.
TIA.

If the phone has a Wi-Fi tethering mode, it should appear in the Wi-Fi menu on your Mac as a wireless network.

Should i update my iphone 4 (not iphone 4s) to ios7.12 or something similar? thanks

hey all
should i update my iphone 4 (not iphone 4s) to ios7.12 or something similar? thanks

This is where everybody who has a problem comes. You cannot judge anything by looking at the place populated only by owners with problems.
Update it or don't. It's not mandatory. I do not believe it's "one of the worst updates" as I have applied every OS update Apple has offered me since 1984, and have yet to have a problem that was not caused by me.

Server side does not detect network failure

Hi folks,
I coded a simple chat program. When a client connects to the multi-thread server, server shows newly connected client's IP address. Now, if the connection between client and server is down, client detects and terminates itself but server does not. The server still shows that client as connected. when I traced the server side, I found out that server was waiting at the readObject (client object input stream) line but it didn't throw any IOException. I tried to send some message to all connected client at every 20 seconds, so I expected to catch IOException when the server did not reach the client. Unfortunately, it didn't work. That is my question how can server side detect network failure?
Thanks for help.
Regards
Bulent

That is how TCP works (noting that it has nothing to do with java.)
Your solution is one of the following or some combination...
- If the server does not receive something every X time period then it disconnects.
- If the server has not received something after X time period it sends a keep alive message to the client. If the client does not respond (or the message fails) then the server disconnects.

After Effects Transform Effect is there something similar in Motion?

Is there a way to something similar to the AE transform effect to offset the motion caused by the displace filter.
Example here:
http://www.videocopilot.net/tutorial/disintegration/
Starting at time 8:06
Thanks
Andrew

Interesting tutorial, thanks!
Here's a quickie Motion version covering the basic concepts they use. I didn't have a texture handy and I wanted this to be self contained, so I used the Cloud generator. I animated the gradient in a gradient generator to get the wipe, substituted Gradient Colorize for "Colorama", Underwater filter for "Turbulent Displace", used behaviors instead of keyframes, etc...
I hope this gets you started:
Disintegrator Movie.
and the Project.
come back with any questions...
Patrick

EBS 11i - Concurrent Manager goes down due to network failure.

Hi,
We have a Single Node Oracle EBS 11i (11.5.10) [upgraded from 11.0.3] Production Instance on a Windows 2003 (32-Bit) server.
We have UPS support for the Server but the Netwok Switch is not on UPS. Due to this whenever there is a power trip the network goes down and due to this the Concurrent Manager (only)goes down. All other Apps Tier and DB Tier services are up inlcluding the 806 Listener (APPS_SID).
Is this how it is designed to work? Is there anyway to ensure that the Conc. Manager does not go down due to network failure.
Rgds,
Thiru

Here it is
Process monitor session ended : 02-OCT-2009 07:30:04
The Internal Concurrent Manager has encountered an error.
Review concurrent manager log file for more detailed information. : 02-OCT-2009 07:43:16 -
Shutting down Internal Concurrent Manager : 02-OCT-2009 07:45:56
Reviver is not enabled, not spawning a reviver process.
List of errors encountered:
_ 1 _
Routine AFPCMT encountered an ORACLE error. ORA-01041: internal error.
hostdef extension doesn't exist
Review your error messages for the cause of the error. (=<POINTER>)
_ 2 _
Routine AFPSMG encountered an ORACLE error. ORA-03114: not connected
to ORACLE
Review your error messages for the cause of the error. (=<POINTER>)
_ 3 _
Routine FDPCRQ encountered an ORACLE error. ORA-03113: end-of-file on
communication channel
Review your error messages for the cause of the error. (=<POINTER>)
APP-FND-01564: ORACLE error 1041 in fdudat
Cause: fdudat failed due to ORA-01041: internal error. hostdef extension doesn't exist.
The SQL statement being executed at the time of the error was: &SQLSTMT and was executed from the file &ERRFILE.
List of errors encountered:
_ 1 _
Routine AFPCAL received failure code while parsing or running your
concurrent program CPMGR
Review your concurrent request log file for more detailed information.
Make sure you are passing arguments in the correct format.
The PROPTRN_1002@PROPTRN internal concurrent manager has terminated with status 1 - giving up.

Something similar to "isdn network-failure-cause" command on Cisco 3600

Similar Messages

Maybe you are looking for